PTSPAS Product Assessment Certificate in accordance with Equivalent Scheme MCHW SHW Volume 1 Clause and

Size: px

Start display at page:

Download "PTSPAS Product Assessment Certificate in accordance with Equivalent Scheme MCHW SHW Volume 1 Clause and"

June Jacobs
5 years ago
Views:

PTSPAS Product Assessment Certificate in accordance with Equivalent Scheme MCHW SHW Volume 1 Clause 104.15 and 104.

eu/en-gb/content/how-to-find-a-tab/55/ Roadmender Asphalt Division of Billian UK Limited Butterthwaite Business Park Butterthwaite Lane Ecclesfield Sheffield S35 9WA Telephone: 0114 245 0968 Email:

com PRODUCT FAMILY: ROADMENDER ASPHALT Product Name: RoadMender Hot Rolled Asphalt to BS EN 13108-4 in compliance with MCHW SHW Volume 1 Clause 911 This PTSPAS Product Assessment Equivalent Scheme

1 PTSPAS Product Assessment Certificate in accordance with Equivalent Scheme MCHW SHW Volume 1 Clause and Pavement Testing Services Ltd Britannia House Unit 1 Rough Hey Road Grimsargh Preston PR2 5AR Technical Assessment Body (TAB) Product Area 23 Road Construction Products Roadmender Asphalt Division of Billian UK Limited Butterthwaite Business Park Butterthwaite Lane Ecclesfield Sheffield S35 9WA Telephone: harry@pavingpellets.com PRODUCT FAMILY: ROADMENDER ASPHALT Product Name: RoadMender Hot Rolled Asphalt to BS EN in compliance with MCHW SHW Volume 1 Clause 911 This PTSPAS Product Assessment Equivalent Scheme Certificate is issued by Pavement Testing Services Ltd (PTS) in accordance with MCHW SHW Clause and Sub-clause (e) requires that The scheme must have a technical supervisory panel that provides technical oversight on the operation of the scheme and formally consents to the issue of assessment and certification requirements of the specialist groups developing the assessment and certification requirements. This panel must include a balanced representation of key end users, recognized industry experts and those responsible for the highways on which such products will be used or installed.the technical supervisory panel includes representation from Highways England (HE), Association of Directors of Environment, Economy Planning and Transport (ADEPT), Road Surface Treatments Association (RSTA), Mineral Products Association (MPA), Joint Authorities Group (JAG), Midlands Highways Alliance (MHA), HAUC(UK) SROH Working Group, HAUC(UK) SROH Innovations Working Group and Transport Scotland. PTSPAS Equivalent Product Assessment Certificates are normally each subject to a review every five years, with annual surveillance. Date Granted - 10 November 2017 Expiry Date 9 November 2022 Next Surveillance 10 November 2018 Next Certificate Review Due by 9 November 2022 Certificate Reference PA Revision status v PTSPAS Certificate Reference PA v Page 1 of 9

2 PRODUCT INTENDED APPLICATIONS Potholes repairs, ironworks, utility reinstatements, airfield repairs, patching, local repairs and any other similar use including narrow trenches MCHW SHW Volume 1 Clause 946 KEY FACTORS ASSESSED Reclaimed Asphalt classification to BS EN Paving Pellets manufacturing process Factory Production Control (FPC) and Quality Management System (QMS) Audits for Paving Pellets and BS EN end product Current BSI QMS accreditation to BS EN ISO 9001: 2008 BSI Certificate Number FM for Paving Pellets and recent audit BSI Certificate of Conformity of the Factory Production Control 0086-CPR in respect of BS EN Bituminous Mixtures. Material Specifications; BS EN Asphalt Concrete, BS EN Hot Rolled Asphalt, BS EN Stone Mastic Asphalt and recent audit Installation Method Statement (IMS) for manufacture and product installation Installation Trials Review of supporting documents Design and Development of Products and Services compliance with BS EN ISO 9001 BSI PD6691:2015+A1:2016 Published Document Guidance on the use of BS EN Bituminous mixtures Material Specifications, Section requires greater levels of control for mixtures with levels of Reclaimed Asphalt above the permissible limits, i.e. 10% for surface course. This Certificate comprises the assessment of surface course material incorporating up to 100% Reclaimed Asphalt. PTS has awarded this Product Assessment Equivalent Scheme Certificate to the Company named above for the products described herein. This product has been assessed by PTS Ltd as being fit for its intended use provided it is manufactured, installed, used and maintained as set out in this Certificate. The issue of this Certificate under Specialist Group PTSSG946, which sets out guidelines and criteria, has been authorised by the PTS Technical Supervisory Panel (PTSTSP). PTSTSP Documents Submission Date: 24 October 2017 PTSTSP Consent Date: by 3 November 2017 Certificate Reference PA Revision status v On behalf of PTS Ltd Signature A J Sewell (Managing Director) Date: Signature P D Wallace (Operations Director) Date: Page 2 of 9

3 1. INSTALLATION SPECIFICATION MCHW SHW Volume 1 Clause 903 and Clause 946.3, and INSTALLATION STANDARD BS Asphalt for roads and other paved areas. Specification for transport, laying, compaction and product type testing protocols 3. INSTALLATION CODE OF PRACTICE SOURCES Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition (England), April 2010 and Second Edition (Wales), came into force January 2007 Specification for the Reinstatement of Openings in Roads (SROR), Second Edition (Northern Ireland), July 2006 and Third Edition (Scotland), January 2015 RSTA ADEPT HE Code of Practice for Ironwork Systems Installation and Refurbishment, May INSTALLATION METHOD STATEMENT (IMS) Contractor s specific IMS taking into account requirements of MCHW SHW Volume 1 Clause and (2016) In accordance with National Highway Sector Schemes NHSS16 or NHSS23 as appropriate NRSWA Operatives Accreditation under the New Roads and Street works Act Where current IMS does not cover all installation activities, the specific IMS will be developed and incorporated in the QMS as appropriate 5. INSTALLATION CERTIFICATION BODY Listed on 6. SUBSTRATA CONDITION ASSESSMENT AND PREPARATORY WORKS MCHW SHW Volume 1 Series 900 Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition (England), April 2010 and Second Edition (Wales), came into force January 2007 Specification for the Reinstatement of Openings in Roads (SROR), Second Edition (Northern Ireland), July 2006 and Third Edition (Scotland), January JOINT PREPARATION Installation Method Statement (IMS) As agreed with the Overseeing Organisation Page 3 of 9

4 MCHW SHW Volume 1 Clause SERVICE PERFORMANCE SPECIFICATION 9. SERVICE PERFORMANCE CODE OF PRACTICE SOURCES Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition, April 2010 RSTA ADEPT HE Code of Practice for Ironwork Systems Installation and Refurbishment, May SERVICE PERFORMANCE TRIAL INSTALLATION PTS (UKAS 4076) Report PTS1719-B-01 Billian-Q-30-10F dated September 2017 Location: RoadMender yard, Sheffield Corehard Ltd Report REP/0417/BIL/INV-001 dated 20 April 2017 Location: Clancy Docwra Head Office, Coppermill Lane, Harefield, Middlesex PTS Report PTS/DER/002/2017 dated September 2017 Site Visual Condition Assessment at Clancy Docwra Head Office after over 2 years in service TRL Client Project Report CPR2213 dated 17 March 2017 Location: Alliance Cockridden Farm Estate Brentwood, Essex 11. SERVICE PERFORMANCE TRIAL INSTALLATION CLIENT BODY AUTHORISING WORK Sponsor: UK Power Networks. Funded by Transport for London Lane Rental Fund Sponsor: UK Power Networks & BT. Funded by Kent Lane Rental Scheme 12. SERVICE PERFORMANCE DETAIL Durability as defined in Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition, April 2010, Section S ) At the end of the guarantee period the condition of the reinstatement shall not be required to be superior, in any respect, to the condition of the adjacent surfaces. 2) Where the profile of the existing surfaces adjacent to the reinstatement is uniform and substantially superior to the surface of the reinstatement, the Undertaker shall carry out remedial work to restore the surface profile of the reinstatement to a condition consistent with the adjacent surfaces. Macrotexture Retention Page 4 of 9

5 13. REQUIREMENTS Product to be manufactured only by the Certificate Owner or Certificate Owner s authorised manufacturer certificated to the current BS EN ISO 9001, following training and receiving a certificate of approval from the Certificate Owner Product to be manufactured using only the raw materials authorized by the Certificate Owner: Reclaimed Asphalt classified to BS EN Aggregate to BS EN Paving Pellets covered by BSI Certificate Number FM , comprising controlled bituminous binder addition Product to be installed only by the Certificate Owner or Certificate Owner s authorised installer meeting the requirements of NHSS16 or NHSS BS EN ISO 9001 PLANNING PROCESS The objective was to plan and develop a Factory Production Controlled (FPC) process for manufacturing BS EN compliant Hot Rolled Asphalt using planings that are crushed, screened, analysed and then blended with aggregate, sand and Paving Pellets in strict adherence to the Quality Management System (QMS). Following successful Type Testing conforming to BS EN , numerous field trials and additional laboratory trials were carried out over a 3-year period. As investment in machinery and access to high PSV surface course planings was required to move to commercial scale production, as an interim step, the Company started out producing the materials in line with the same process however using virgin aggregate. This product was granted certification by the BSI on 05 November 2015 with Certificate Number 0086-CPR Certificate of Conformity of the Factory Production Control in respect of EN :2006 Hot Rolled Asphalt. Further funds were raised from the Kent Lane Rental Fund that enabled the Company to invest in multiple additional performance trials to further verify the performance. The Company also raised funds to invest in covered storage, crushing, screening, blending and bagging equipment required to manufacture the product. 15. BS EN ISO 9001 DESIGN INPUTS MCHW SHW Volume 1 Clause and Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition, April 2010 Declared grading in accordance with the requirements of BS EN :2016, Table 3 or Table 4 and BSI PD 6691:2015+A1:2016 Annex C Declared binder content in accordance with BS EN :2016, Section and BSI PD 6691:2015+A1:2016 Annex C, Section C2.5 Declared maximum mixing temperature Stiffness: 1 GPa after 28 days when tested in accordance with BS EN (ITSM method 20 C) Page 5 of 9

6 Resistance to permanent deformation as defined in BSI PD 6691:2015+A1:2016 Annex C, Table C.3 The initial surface texture shall be not less than 0.9mm when measured using the volumetric patch method described in BS EN Note: coated chippings conforming to BSI PD 6691:2015+A1:2016 Annex C, Section C2.8 shall be applied for HRA containing 35% or less nominal coarse aggregate content to achieve the required surface texture. The minimum wet Skid Resistance value shall not be less than 60 when determined using the portable skid resistance tester (pendulum) in accordance with BS EN Air Voids Content shall be as stated in Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition, April 2010, Table S10.1, Section S Thickness shall be as stated in Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition, April 2010, Table A2.1, Section A2.6.1 Durability shall be assessed as stated in Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition, April 2010, Section S BS EN ISO 9001 VERIFICATION PROCESS PTS Laboratory (UKAS 4076) Report PTS1519-B-02 dated July 2015 Resistance to permanent deformation Wheel Tracking BS EN small device, Procedure A at 60 o C BS WTR air RD air Maximum Rut Depth 0.69m/cycle 2.3mm 2.3mm TRL Client Project Report CPR2213 dated 8 April 2016 (i) Resistance to permanent deformation Wheel Tracking BS EN small device, Procedure A at 60 o C WTR air 0.148m/cycle RD air 4.37mm (ii) Indirect Tensile Stiffness Modulus at 20 o C to BS EN Annex C: 2885MPa (iii) Retained Stiffness Modulus after soaking for 24 hours at 60 o C, range: 70.0% 111.4% (iv) Composition Analysis to BS EN & 2: binder content in compliance with BSI PD 6691:2015+A1:2016, Annex C, Table C.2A (v) Recovered binder data: Binder recovery to BS EN Needle penetration at 25 0 C to BS EN 1426, range: 42d mm - 44d mm Softening point (Ring and Ball Method) to BS EN 1427: C (vi) Crack Propagation by Semi-Circular Bender (guidance only) to BS EN , range: 31.2 N/mm N/mm 1.5 (vii) Air Voids Contents to BS EN , range: 3.0% 3.8% Page 6 of 9

7 17. BS EN ISO 9001 VALIDATION PROCESS Corehard Ltd Report REP/0417/BIL/INV-001 dated 20 April 2017 Location: Clancy Docwra Head Office, Coppermill Lane, Harefield, Middlesex Various recycling options were adopted for repairs of already damaged areas in March Visual inspection of patches after 2 years in service under heavy trafficking reported good condition and no signs of any observable issues such as surface cracking, edge depression, crazing or surface depression PTS Report PTS/DER/002/2017 dated September 2017 Site Visual Condition Assessment The inspection of the patches repairs after over 2 years in service under high stress levels reported good condition. PTS (UKAS 4076) Report PTS1719-B-01 Billian-Q-30-10F dated September 2017 (as installed) Location: RoadMender yard, Sheffield (i) Resistance to permanent deformation Wheel Tracking BS EN small device, Procedure A at 60 o C WTR air 0.70m/cycle RD air 2.2mm (ii) Indirect Tensile Stiffness Modulus at 20 o C to BS EN Annex C, average: 3243MPa (iii) Composition Analysis to BS EN & 2: binder content in compliance with BSI PD 6691:2015+A1:2016, Annex C, Table C.2A (iv) Air Voids Contents to BS EN , average: 5.9% TRL Client Project Report CPR2213 dated 17 March 2017 Location: Alliance Cockridden Farm Estate Brentwood, Essex (i) Resistance to permanent deformation Wheel Tracking BS EN small device, Procedure A at 60 o C WTR air 3 months 6 months 12 months 3 months 6 months 12 months 2.12m/cycle 1.45m/cycle 1.41m/cycle 3.46mm 3.42mm 3.83mm RD air (ii) Skid Resistance (Pendulum Test Value) in accordance with BS EN mean corrected PTV range from 79.6 to 89.0 after 3 months in service mean corrected PTV 88 after 6 months in service mean corrected PTV 85 after 12 months in service Page 7 of 9

8 (iii) Thickness, range: 46.0mm 68.6mm Note: Thickness in excess of those specified in Table A2.1, Section A2.6.1 of the Department for Transport New Roads and Street Works Act 1991 Specification for the Reinstatement of Openings in Highways (SROH), Third Edition, April 2010, was targeted for the purpose of laboratory studies. The nominal compacted layer thickness shall be as specified above. Processes integrated in the Client QMS: 18. BS EN ISO 9001: 2015 SECTION 8.3 CHANGES PROCESS Identification of authorised competent person Identification and assessment of change generated adverse impact 19. TECHNICAL SPECIFICATION FOR MANUFACTURE RoadMender DBP 250 Volumetric Hot-Mix Asphalt Method Statement PR-B5-021 (2) RoadMender DBP 500 Volumetric Hot-Mix Asphalt Method Statement PR-B5-023 (2) 20. TECHNICAL SPECIFICATION FOR DELIVERY 20Kg bags labelled accordingly, as specified in QMS and Production Procedure ref PR-B5-040 (2) 21. TECHNICAL SPECIFICATION FOR SITE HANDLING Part of training provided by Roadmender covered under QMS: RoadMender DBP 250 Operating Checklist PR-B5-065 (1) RoadMender DBP 500 Operating Checklist PR-B5-066 (1) RoadMender Training Completion Confirmation FM-B5-021 (1) RoadMender DBP 250 Volumetric Hot-Mix Asphalt Method Statement PR-B5-021 (2) RoadMender DBP 500 Volumetric Hot-Mix Asphalt Method Statement PR-B5-023 (2) RoadMender Operations Risk Assessment FM-B5-022 (1) RoadMender DBP 250 User and Service Manual PR-B5-022 (3) RoadMender DBP 500 User and Service Manual PR-B5-024 (2) 22. TEST RESULTS Available on request of the Overseeing Organisation from the Certificate Owner, comprising the verification and on-going validation processes Page 8 of 9

9 CONDITIONS OF CERTIFICATION 1. This Certificate: relates only to the product/system that is named and described on the front page is issued only to the company, firm, organisation or person named on the front page no other company, firm, organisation or person may hold or claim that this Certificate has been issued to them has to be read, considered and used as a whole document it may be misleading and will be incomplete to be selective is copyright of PTS Ltd. PTS Product Assessment forms part of the Product Acceptance Scheme as described in MCHW SHW Volume 1 Clause and shall be submitted by the Contractor to the Overseeing Organisation for Approval. 2. Publications, documents, specifications, legislation, regulations, standards and the like referenced in this Certificate are those that were current and/or deemed relevant by PTS Ltd at the date of issue or reissue of this Certificate. 3. This Certificate will remain valid for an unlimited period provided that the product/system and its manufacture and/or fabrication, including all related and relevant parts and processes thereof: are maintained at or above the levels which have been assessed and found to be satisfactory by PTS Ltd continue to be checked as and when deemed appropriate by PTS Ltd under arrangements that it will determine are reviewed by PTS Ltd as and when it considers appropriate remain in accordance with the requirements of PTSPAS. 4. PTS Ltd has used due skill, care and diligence in preparing this Certificate, but no warranty is provided. 5. In issuing this Certificate, PTS Ltd is not responsible and is excluded from any liability to any company, firm, organisation or person, for any matters arising directly or indirectly from: the presence or absence of any patent, intellectual property or similar rights subsisting in the product/system or any other product/system the right of the Certificate holder to manufacture, supply, install, maintain or market the product/system individual installations of the product/system, including their nature, design, methods, performance, workmanship and maintenance any works and constructions in which the product/system is installed, including their nature, design, methods, performance, workmanship and maintenance any loss or damage, including personal injury, howsoever caused by the product/system, including its manufacture, supply, installation, use, maintenance and removal. 6. Any information relating to the manufacture, supply, installation, use, maintenance and removal of this product/ system which is contained or referred to in this Certificate is the minimum required to be met when the product/system is manufactured, supplied, installed, used, maintained and removed. It does not purport in any way to restate the requirements of the Health and Safety at Work etc. Act 1974, or of any other statutory, common law or other duty which may exist at the date of issue or reissue of this Certificate; nor is conformity with such information to be taken as satisfying the requirements of the 1974 Act or of any statutory, common law or other duty of care. Page 9 of 9

PTSPAS Product Assessment Certificate in accordance with Equivalent Scheme MCHW SHW Volume 1 Clause and

PTSPAS Product Assessment Certificate in accordance with Equivalent Scheme MCHW SHW Volume 1 Clause 104.15 and 104.16 Pavement Testing Services Ltd Britannia House Unit 1 Rough Hey Road Grimsargh Preston