White House Products Ltd

Transcription

1 White House Products Ltd Issue 5 - Section 3 To view a gear pump, please click on the name below or use the bookmarks in your PDF software. To return to this page, please click on the red text in the top corner of each page. Introduction and ontact Details SNP 2 Series Pumps eta S12 Pump Selection eta S12 ontinental/earing Supported Drives 36 eta S12 Relief Valves 37 eta S12 Pumps with Priority Flow ontrol and Relief Valve Assemblies 37 eta S17 Pump Selection eta S17 ontinental/earing Supported Drives 42 eta S17 Relief Valves 43 eta S17 Pumps with Priority Flow ontrol and Relief Valve Assemblies 43 SP Series Gear Pumps PGP502 Pump Selection PGP502 Relief Valves 49 PGP505 Pump Selection PGP505 Relief Valves 54 PGP511 Pump Selection PGP511 ontinental/earing Supported Drives PGP511 Relief Valves 61 PGP511 Pumps with Priority Flow ontrol and Relief Valve Assemblies 61 PGP517 Pump Selection PGP517 ontinental/earing Supported Drives 65 PGP517 Relief Valves 66 PGP517 Pumps with Priority Flow ontrol and Relief Valve Assemblies 66 PGP620 Pump Selection PGP620 ontinental/earing Supported Drives 70 uilding PGP620/640 Double Pumps 70 PGP640 Pump Selection David rown / Hydreco Q Series Pumps David rown QR4 Series Gear Pumps 75 and 77 David rown QS4 Series Gear Pumps 76 and 77 David rown QR5 Series Gear Pumps 78 and 80 David rown QS5 Series Gear Pumps 79 and 80 David rown QR6 Series Gear Pumps 81 and 83 David rown QS6 Series Gear Pumps 82 and 83 David rown QS7 Series Gear Pumps QR4, QS4, QR5, QS5, QR6, QS6, QS7 - Ports 86 David rown / Hydreco Q Series Multiple Pumps 87 International UK sales@whp.co.uk Fax White House Products Ltd, Kelburn usiness Park, Port Glasgow, Renfrewshire, PA14 6TD, Great ritain

2 click here to return to front page Welcome to the White House Products Ltd atalogue Our promise to you... That over 90% of orders are delivered from stock! That all UK back orders are delivered FO. That all stocked UK single pump and motor orders not requiring modification ordered before 4pm will be dispatched the SAME DAY. That any part supplied by us in error and unused by you will be collected by our courier from you and credited in full - inclusive of any carriage and packing costs - on its return. That any part ordered in error by you and returned to us as new will be credited in full against the correct replacement supplied by us. That we shall try our very best at all times to provide you with what you want. That if we don t have a particular pump or motor in stock we will offer to manufacture a replacement where this is possible. Ex-Stock Availability All items shown in this catalogue are stock items and therefore normally available for immediate despatch. Enquiries, Pricing & Ordering Telephone UK International Fax sales@whp.co.uk Postal Address White House Products Ltd Kelburn usiness Park, Port Glasgow, Renfrewshire, PA14 6TD, Great ritain Prices and secure online ordering at To obtain prices from our website you need to have a username and password..if you don't have these, by going to and clicking on Register. You will get a username and password by return. Internet ordering can be done using a credit account, if this has already been set up, or by credit card. To provide total security to our credit card customers, payments are transacted using Sage Pay's secure server. y whatever means you use, we look forward to hearing from you!

3 click here to return to front page SNP2 Pump Selection - Ordering ode, Seal Kits and Specifications SNP2 - Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PASN2 08 M1 80 V (8cc/rev capacity, M1 shaft, 80 flange, single pump, side ports, viton seal) PASN2 08 M1 80 F V (8cc/rev capacity, M1 shaft, 80 flange, front section, sealed inlet, viton seal) PASN2 08 M1 80 A V (8cc/rev capacity, M1 shaft, 80 flange, front section, common inlet, viton seal) PASN2 08 M1 80 P V (8cc/rev capacity, M1 shaft, 80 flange, rear ported, viton seal) PASN2 19 A (19cc/rev capacity, centre section, side ports only) PASN2 14 E (14cc/rev capacity, back section, side ports only) Front/Single Pump PASN2 * $$???!!! entre/ack Section PASN2 $$ && * Rotation A Anti-lockwise lockwise $$ apacity 04 4 cc/rev 06 6 cc/rev 08 8 cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev??? Shaft see codes in purple boxes under shaft diagrams on page 30!!! Mounting Flange see codes in purple boxes under flange diagrams on page Shaft Seal N V Nitrile Seal Viton Seal % Model/Features F A P single pump front section front section single or rear section side ports only sealed between sections common inlet rear ported $$ apacity 04 4 cc/rev 06 6 cc/rev 08 8 cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev % Model/Features A centre section side ports only E back section side ports only SNP2 - Specifications Pump Model Displacement cc/rev in3/rev Peak Pressure bar psi Rated Pressure bar psi Minimum speed at bar rpm Minimum speed at bar rpm Minimum speed at 180 bar to rated pressure rpm Maximum Speed rpm ody Length mm SNP2 - Ports (all flange ports available with alternative tappings) Ports of your choice - see page 31 for options. Please specify your port choice when ordering. SNP2 - Lengths Standard End over (E): 19.65mm Portable End over (P): 31.80mm Unsealed entre Plate: 17.8mm Sealed entre Plate Pair: 19.2mm SNP2 - Seal Kit Ordering ode Nitrile: SNP2A03 Viton: SNP2A02 29

4 click here to return to front page SNP2 Pump Selection - Shafts and Mounting Flanges SNP2 - Shaft Type M12 x K1 1:5 Taper (not for H flange) Torque Rating Nm L1 5/8 Parallel (not for H flange) Torque Rating - 90 Nm M1 Long DIN Tooth Spline Torque Rating - 75 Nm P1 15mm Parallel (single pump drives only, cc/rev only). Torque Rating Nm M12 x S1 SAE A 9 Tooth (not for H flange) Torque Rating - 75 Nm T1 1:8 Taper (not for H flange) Torque Rating Nm U1 Tang/Spade Drive (H flange only) Torque Rating - 70 Nm Z1 Short DIN Tooth Spline (not for H flange) Torque Rating - 90 Nm Maximum torque transmission capability of SNP2-SNP2 connecting shafts: 70 Nm SNP2 - Mounting Flange Type ø ø ø H L ø ø ø R S X36 30

5 click here to return to front page SNP2 Pump Selection - Ports SNP2 - Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 29) x 48.2 mm SP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x ø Holes 1/4" - 20 UN x 12.7 min thread øh 4 Holes 5/16 x 18 UN x 14 min full thread (M8) SP OPL Dowty 1PL Dowty - 5/16-18 UN Tappings (M8) ø Size (Ax) 12 x x x 40 ø Size (Ax) 8 x x x x x x x 55 Size A M M M6 Tapping M6 x 1 tapped European Diamond (metric) European Square (metric) HPI ø Size (Ax) 5/8 x 36 7/8 x 48 JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 1 x 14 1 x /4 x 11 Metric Size 14 x x x x x x 2 33 x 2 Japanese Diamond JSP Metric NPT Size 1/8 x 28 1/4 x 18 3/8 x 18 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 SAE Size 7/16 x 20 1/2 x 20 9/16 x 18 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x 12 Size A 1/2" /4" NPT SAE 'O' Ring SAE Split Flange - 1/2 available in vertical position 31

6 click here to return to front page eta S12 Pump Selection - Ordering ode, Seal Kits and Specifications eta S12 - Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAS J1 L1 AV (4cc/rev, J1 shaft, L1 flange, front pump, side ports and viton shaft seal) PAS J1 SA2 V (4cc/rev, J1 shaft, SA2 flange, single pump, blank back cover, side ports and viton shaft seal) PAS K1 80 PV (4cc/rev, K1 shaft, 80 flange, single pump, portable back cover, side or rear ports and viton shaft seal) PAS A (11.2cc/rev capacity, centre section, side ports only, section with drive for another pump) PAS E (11.2cc/rev capacity, back section, side ports only, blank back cover) PAS P (11.2cc/rev capacity, back section, side or rear ports, portable back cover) Front/Single Pump entre/ack Section PAS12 *** $$???? && PAS12 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$ Shaft see codes in purple boxes under shaft diagrams on page 33???? Mounting Flange see codes in purple boxes under flange diagrams on page 34 && Model/Features AV V PV front pump single pump single pump side ports only front section viton shaft seal side ports only blank back cover (not portable) viton shaft seal side or rear ports portable back cover viton shaft seal *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model/Features A E P centre section side ports only section with drive for another pump back side ports only section blank back cover (not portable) back side or rear ports section portable back cover eta S12 - Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar Max Intermittent Pressure bar Start Pressure bar Maximum Speed rpm Minimum Speed rpm ody Length mm eta S12 - Ports (all flange ports available with alternative tappings) Ports of your choice - see page 35 for options. Please specify your port choice when ordering. eta S12 - Lengths Standard End over (E): 19mm Portable End over (P): 32mm Unsealed entre Plate: 6.9mm Sealed entre Plate Pair: 31mm eta S12 - Seal Kit Ordering ode For a front or single pump: PAS12SK For a centre or back section: PAS12/RSK 32

7 click here to return to front page eta S12 Pump Selection - Shafts eta S12 - Shaft Type stand out with X36 DP 11/16 Dowty Parallel Torque Rating Nm +0 ø stand out with 80 J1 18mm Parallel Torque Rating Nm ø ø stand out with 80 K1 1:5 Taper with M12 x 1.5 Thread & 3mm Wide Key Torque Rating Nm stand out with SA2 L1 5/8 SAE A Parallel Torque Rating - 72 Nm +0 ø stand out with SA2 L2 5/8 SAE A Long Parallel Torque Rating - 72 Nm +0 ø M1 DIN Tooth Spline Torque Rating Nm stand out with ø stand out with SA2 Q1 3/4"11 x 23mm SAE Spline Torque Rating Nm +0 ø stand out with SA2 Q2 3/4"11 x 29.2mm SAE Spline Torque Rating Nm +0 ø Q3 3/4"11 x 46.5mm SAE Spline Torque Rating Nm R1 11/16 SAE, 10 Tooth Spline Torque Rating Nm stand out with SA2 S1 5/8 SAE A, 9 Tooth Spline - Limit max pressure to 140 bar at 31cc & to 100 bar at 33cc Torque Rating Nm stand out with SA stand out with X36 T1 1.8 Taper with M12 x 1.5 Thread & 3.2mm Wide Key Torque Rating Nm +0 ø ø ø14.7 S13 7/8" SAE, 13 Tooth Spline - Limit max pressure to 140 bar at 31cc and to 100 bar at 33cc Torque Rating Nm stand out with SA2 R2 Mitsubishi 10 Tooth Spline Torque Rating Nm stand out with SA stand out with UR U1 8 mm Tang/Spade Torque Rating - 75 Nm +0 ø ø ø R3 11/16 SAE Long, 10 Tooth Spline Torque Rating Nm /4"SAE Parallel 75.3 ø20 ø S15 15 Tooth JIS Spline Torque Rating Nm 30.8 ø stand out with SA2 Y1 Torque Rating Nm ø stand out with SA2 Y2 3/4"SAE Long Parallel Torque Rating Nm +0 ø M8x ø stand out with SA2 Y3 3/4"SAE Parallel with 1/2"- 20 UNF Thread Torque Rating Nm Maximum torque transmission capability of S12-S12 connecting shafts: 110 Nm 33

8 click here to return to front page eta S12 Pump Selection - Mounting Flanges eta S12 - Mounting Flange Type ø ø ø11 ø ø80 96 ø36.5 SA2 SAE A 2 olt 80 DIN (osch) 4 olt X36 Italian/European 4 olt ø ø50 ø52 ø52 L1 DEUTZ Engine 2 olt with 50mm Pilot ø11 L2 DEUTZ Style 2 olt with 52mm Pilot ø11 UR 52mm Pilot 2 or 4 through olt ø50 ø14.3 ø ø11.2 ø x ø9 4 x ø8 ø11 R1 International Harvester (IH) 2 olt with 50 mm pilot 88 ø20 71 ø X75 Valtra 75 mm Pilot /8-16 UN ø through 4 x ø S2W SAE 2 olt ø P52O Perkins 4236 Flange x ø R 6 olt Round, 82.6mm PD 71 ø HIT Hitachi 36 mm Pilot try the quick order function on our website for easy re-ordering ø10.8 ø ø Allis / Renault ø

9 click here to return to front page eta S12 Pump Selection - Ports eta S12 - Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 32) x 48.2 mm SP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x ø Holes 1/4" - 20 UN x 12.7 min thread øh 4 Holes 5/16 x 18 UN x 14 min full thread (M8) SP OPL Dowty 1PL Dowty - 5/16-18 UN Tappings (M8) ø Size (Ax) Tapping 12 x 26 M5 13 x 30 M6 19 x 40 M6 19 x 40 M8 Exceptions only only ø Size (Ax) Tapping Exceptions 8 x 26 M5 10 x 26 M5 13 x 30 M6 15 x 35 M6 20 x 40 M8 18 x 55 M8 110 and 26 x 55 M8 above only M6 x 1 tapped Size A M M6 26* 22.4* 47.6* M6 * Exceptions and above only Tapping European Diamond (metric) European Square (metric) HPI ø Size (Ax) 5/8 x 36 7/8 x 48 JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 1 x 14 1 x /4 x 11 Metric Size 14 x x x x x x 2 33 x 2 Japanese Diamond JSP Metric NPT NPT Size 1/8 x 28 1/4 x 18 3/8 x 18 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 SAE 'O' Ring SAE Size 7/16 x 20 1/2 x 20 9/16 x 18 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x 12 SAE Flange A Tapping Metric Tapping UN 1/2" M8 x /16" - 18 UN 3/4" M10 x 1.5 3/8" - 16 UN 1" M10 x 1.5 3/8" - 16 UN 1 1/4" M10 x 1.5 3/8" - 16 UN SAE Split Flange 1/2", 3/4" and 1" available in vertical position 35

10 click here to return to front page eta S12 ontinental/earing Supported Drives These subassemblies are used when an inbuilt bearing supported shaft is required, such as for pulley driven pumps or when a one piece shaft is not available. eta S12 ontinental/earing Supported Drives - Ordering odes Use this chart to compile your ordering code. For example: PAS12 K1 SA2 (K1 shaft, SA2 flange) PS12DS K1 (K1 shaft only) PS12MSE SA2 (SA2 flange only) PAS12 $$???? $$ Shaft see codes in purple boxes under shaft diagrams below Subassembly $$ Mounting Flange see codes in purple boxes under flange diagrams below Shaft PS12DS $$ $$ Shaft see codes in purple boxes under shaft diagrams below Flange If being used as part of a single pump, use with S12 pump assembly PAS12***E or PAS12***P, unless the pump is also to have a Relief Valve or Priority Flow ontrol cover in which case use in conjunction with PAS12***A If being used as the drive for a multiple pump, use in conjunction with PAS12***A which becomes the front pump section. PS12MSE???? $$ Mounting Flange see codes in purple boxes under flange diagrams below eta S12 ontinental/earing Supported Drives - Shafts ø M12 x 1.5 ø20 ø28 ø17 13 ø13.6 K1 DIN 1:5 Taper Torque Rating - 130Nm ø ø key: 4x4 ø ø13.97 ø28 20 ø Tooth Spline M6 x 1 L1 5/8 SAE A Parallel Torque Rating - 72Nm ø21.79 ø20 21 Tooth Spline ø28 13 Tooth Spline S13 7/8 SAE, 13 Tooth Spline Torque Rating - 130Nm ø ø20 ø28 20 ø Tooth Spline 1/4" - 20 UN - 2 Y2 3/4 SAE Long Parallel Torque Rating - 130Nm ø20 key: 4x ø13.97 ø28 M6 x Tooth Spline L2 5/8 SAE A Long Parallel Torque Rating - 72Nm key: 4.76 x eta S12 ontinental/earing Supported Drives - Mounting Flanges ø ø52 8 ø80 ø ø52 8 ø82.6 ø ø52 ø DIN (osch) 4 olt ontinental SA2 SAE A, 2 olt ontinental 36 S2 SAE, 2 olt ontinental

11 click here to return to front page eta S12 Relief Valves eta S12 Relief Valves - Ordering ode PAS12IRV internal drain into the inlet side of pump PAS12ERV external drain to tank When built into single pumps use in conjunction with PAS12***$$????AV. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAS12***A. eta S12 Relief Valves - Specifications Fitting Fitted into the end cover of the pump. Pressure fully adjustable between 7 and 210 bar ( psi) Length 30mm External Drain Ports SP up to 1/2 SAE O Ring up to 3/4 Metric up to 20mm eta S12 Pumps with Priority Flow ontrol and Relief Valve Assemblies eta S12 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Ordering ode Use this chart to compile your ordering code - e.g. PAS12PPF 03 (pump with a flow control setting of 3 l/min or 0.66 gpm). PAS12PPF $$ $$ Flow ontrol Setting Relief Valve Adjustment Range 03 3 l/min (0.66 gpm) bar ( psi) 06 6 l/min (1.32 gpm) bar ( psi) 09 9 l/min (2 gpm) bar ( psi) l/min (2.64 gpm) bar ( psi) When built into single pumps use in conjunction with PAS12***$$????AV. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAS12***A. eta S12 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Specifications Relief Valve Requirements Priority flow is pressure compensated, bypass port pressure can exceed priority pressure. The inbuilt relief valve acts on the priority line and drains into the inlet of the pump. The bypass port line, if not draining to tank, requires an external relief valve to protect it. Length 66.4 mm Port (side or rear) Priority - 3/4" SAE O Ring Secondary - 7/8" SAE O Ring 37

12 click here to return to front page eta S17 Pump Selection - Ordering ode, Seal Kits and Specifications eta S17 - Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAS K2 SA2 AV (13.7cc/rev capacity, K2 shaft, SA2 flange, front pump/section, side ports only, viton seal) PAS K2 SA2 PV (13.7cc/rev capacity, K2 shaft, SA2 flange, single pump, side or rear ports, portable back cover, viton seal) PAS A (13.7cc/rev capacity, centre section, side ports only, section with drive for another pump) PAS P (13.7cc/rev capacity, back section, side or rear ports, portable back cover) Front/Single Pump entre/ack Section PAS17 *** $$???? && PAS17 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$ Shaft see codes in purple boxes under shaft diagrams on page 39???? Mounting Flange see codes in purple boxes under flange diagrams on page 40 && Model/Features AV PV front pump single pump side ports only front section viton shaft seal side or rear ports portable back cover viton shaft seal *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model/Features A P centre section side ports only section with drive for another pump back side or rear ports section portable back cover eta S17 - Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar Max Intermittent Pressure bar Start Pressure bar Maximum Speed rpm Minimum Speed rpm ody Length mm eta S17 - Ports (all flange ports available with alternative tappings) Ports of your choice - see page 41 for options. Please specify your port choice when ordering. eta S17 - Lengths Length of Standard End over: 32.7 mm Length of Portable End over: 32.7 mm Length of Unsealed entre Plate: 5.8 mm Length of Sealed entre Plate: 42 mm eta S17 - Seal Kit Ordering ode For a front or single pump: PAS17SK For a centre or back section: PAS17/RSK 38

13 click here to return to front page eta S17 Pump Selection - Shafts eta S17 - Shaft Type Ø20 +0 ø stand out with 100 K2 1:5 Taper with M16 x 1.5mm Thread & 5mm Wide Key Torque Rating Nm P1 7/8 SAE Parallel Torque Rating Nm 41.3 stand out with S stand out with S2 +0 ø stand out with S P2 7/8 SAE Long Parallel Torque Rating Nm S2 7/8 SAE, 13 Tooth Spline Torque Rating Nm stand out with S2 S3 7/8 SAE, 13 Tooth Spline Torque Rating Nm stand out with S2 S4 7/8 SAE Long, 13 Tooth Spline Torque Rating Nm Ø ø stand out with X50 T2 1:8 Taper with M14 x 1.5mm Thread & 4mm Wide Key Torque Rating Nm 48.1 stand out with S2 Q3 3/4 SAE, 11 Tooth Spline Torque Rating Nm Maximum torque transmission capability of S17-S17 connecting shafts: 258 Nm 39

14 click here to return to front page eta S17 Pump Selection - Mounting Flanges eta S17 - Mounting Flange Type 88.4 ø ø ø ø DIN 4 olt 100mm Pilot 105 DIN 4 olt (osch)105mm Pilot ø ø14.3 ø101.6 ø52 SA2 SAE A 2 olt 21.0 S2 SAE 2 olt ø ø ø X50 Italian/European 4 olt ø50.8 high quality products at competitive prices with fast delivery ø11.2 ø82.6 ø82.6 ø F 6 olt Flange ø42.78 H8 5 ø29.1 ø6 8 6FORD 6 olt Ford PTO ø40 57 ø ø66.68 ø63.7 ø51 40

15 click here to return to front page eta S17 Pump Selection - Ports eta S17 - Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 38) x 68.5 mm SP SP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 ø48.1 ø25.4 ø48.1 ø19 inlet outlet 2PL Dowty - 5/16-18 UN Tappings (M8) ø Size (Ax) 12 x 26 M5 13 x 30 M6 19 x 40 M8 European Diamond (metric) Tapping 27 x 51 M10 19x56 M10 27x56 M10 32x62 M10 38x72 M10 ø Size (Ax) Tapping 8 x 26 M5 10 x 26 M5 13 x 30 M6 15 x 35 M6 20 x 40 M6 18 x 55 M8 26 x 55 M8 Size A ø Size (Ax) 5/8 x 36 7/8 x 48 M8 x 1.25 tapped European Square (metric) HPI Japanese Diamond JSP JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 Metric Metric Size 14 x x x x x x 2 30 x x 2 42 x 2 NPT NPT Size 1/8 x 28 1/4 x 18 3/8 x 18 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 SAE Size 7/16 x 20 1/2 x 20 9/16 x 18 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x /8 x /2 x 12 SAE 'O' Ring SAE Flange A Tapping Metric Tapping UN 1/2" M8 x /16" - 18 UN 3/4" M10 x 1.5 3/8" - 16 UN 1" M10 x 1.5 3/8" - 16 UN 1 1/4" M10 x 1.5 3/8" - 16 UN 1 1/2" M12 x /2" - 13 UN 2" M12 x /2" - 13 UN SAE Split Flange - 1/2, 3/4" and 1" available in vertical position 41

16 click here to return to front page eta S17 ontinental/earing Supported Drives These subassemblies are used when an inbuilt bearing supported shaft is required, such as for pulley driven pumps or when a one piece shaft is not available. eta S17 ontinental/earing Supported Drives - Ordering odes Use this chart to compile your ordering code. For example: PAS17 P3 SA2 (P3 shaft, SA2 flange) PS17DS P3 (P3 shaft only) PS17SE SA2 (SA2 flange only) Subassembly Shaft Flange PAS17 $$???? PS17DS $$ PS17SE???? $$ Shaft see codes in purple boxes under shaft diagrams below $$ Mounting Flange see codes in purple boxes under flange diagrams below $$ Shaft see codes in purple boxes under shaft diagrams below $$ Mounting Flange see codes in purple boxes under flange diagrams below If being used as part of a single pump, use with S17 pump assembly PAS17***P, unless the pump is also to have a Relief Valve or Priority Flow ontrol cover in which case use in conjunction with PAS17***A If being used as the drive for a multiple pump, use in conjunction with PAS17***A which becomes the front pump section. eta S17 ontinental/earing Supported Drives - Shafts ø Tooth Spline ø107.1 ø66.4 ø15.2 ø ø15.5 ø25.4 ø30.0 ø23.8 Key: 1" x 1/4" x 3/8" ø24.9 ø P3 7/8" SAE Parallel Short Torque Rating - 251Nm ø18.3 ø ø15.5 ø25.4 ø23.9 ø Tooth Spline 13 Tooth Spline S3 7/8" SAE, 13 Tooth Spline Torque Rating - 258Nm ø15.5 ø25.4 ø30.0 ø P4 7/8" SAE Parallel Long Torque Rating - 251Nm Key: 1" x 1/4" x 3/8" ø18.3 ø Tooth Spline ø ø18.3 ø24.9 ø15.5 ø25.4 ø30 ø Tooth Spline 15 Tooth Spline S 1" SAE, 15 Tooth Spline Torque Rating - 258Nm 15.2 ø18.3 ø31.3 ø25.4 ø30 ø Tooth Spline 14 Tooth Spline S4 1 1/4" SAE, 14 Tooth Spline Torque Rating - 258Nm ø Tooth Spline 66.4 ø15.5 Y3 3/4" Parallel Torque Rating - 258Nm ø ø25.4 ø P 1" SAE Parallel Torque Rating - 258Nm Key: 3/16" x 3/16" x 1 3/4" ø18.3 ø ø Tooth Spline ø15.5 ø25.4 ø30.0 Key: 1 1/4" x 1/4" x 3/8" 28.1 ø ø ø15.5 ø25.4 ø Tooth Spline 13 Tooth Spline S5 7/8" SAE, 13 Tooth Spline Torque Rating - 258Nm eta S17 ontinental/earing Supported Drives - Mounting Flanges ø ø52 38 SA2 SAE A, 2 olt ontinental ø S2 SAE, 2 olt ontinental ø52 ø

17 click here to return to front page eta S17 Relief Valves eta S17 Relief Valves - Ordering ode PAS17IRV internal drain into the inlet side of pump PAS17ERV external drain to tank When built into single pumps use in conjunction with PAS17***$$????AV. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAS17***A. eta S17 Relief Valves - Specifications Fitting Fitted into the end cover of the pump. Pressure fully adjustable between 7 and 210 bar ( psi) Length 33mm External Drain Port SP up to 1/2 SAE O Ring up to 3/4 Metric up to 20mm eta S17 Pumps with Priority Flow ontrol and Relief Valve Assemblies eta S17 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Ordering ode Use this chart to compile your ordering code - e.g. PAS17PPF 03 (pump with a flow control setting of 3 l/min or 0.66 gpm). PAS17PPF $$ $$ Flow ontrol Setting Relief Valve Adjustment Range 03 3 l/min (0.66 gpm) bar ( psi) 07 7 l/min (1.54 gpm) bar ( psi) l/min (2.42 gpm) bar ( psi) l/min (3.30 gpm) bar ( psi) l/min (4.18 gpm) bar ( psi) l/min (5.07 gpm) bar ( psi) l/min (5.95 gpm) bar ( psi) l/min (6.83 gpm) bar ( psi) l/min (7.71 gpm) bar ( psi) l/min (8.59 gpm) bar ( psi) l/min (9.47 gpm) bar ( psi) When built into single pumps use in conjunction with PAS17***$$????AV. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAS17***A. eta S17 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Specifications Relief Valve Requirements Priority flow is pressure compensated, bypass port pressure can exceed priority pressure. The inbuilt relief valve acts on the priority line and drains into the inlet of the pump. The bypass port line, if not draining to tank, requires an external relief valve to protect it. Length 76 mm Port Inlet Rear - 1 5/8" SAE 'O' Ring Priority - 3/4" SAE O Ring (side or rear) Secondary - 1 1/16" SAE O Ring (side or rear) 43

18 click here to return to front page SP Gear Pump Selection - Ordering ode, Seal Kits and Specifications SP Ordering ode (single pump with side/rear ports of your choice) Use this chart to compile your ordering code - e.g. PASP25 A 200 K4 S2 (anti-clockwise, 20.0cc/rev capacity, K4 shaft, S2 flange, single section). PASP25 * $$$??!!! * Rotation A Anti-lockwise lockwise $$$ apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev?? Shaft K4 1:5 Taper with M14 x 5mm wide key Q5 SAE 11 Tooth Spline S2 SAE 13 Tooth Spline T2 1:8 Taper!!! Flange S2 SA2 10 X50 T1 N82 SAE 2 olt SAE A 2 olt DIN 4 olt, 100mm Pilot Italian/European 4 olt, 50.8mm Pilot Perkins 1000 Series Nihon Spindle % over Single Section SP Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw ody Length mm Approximate Overall Length mm SP Ports (all flange ports available with alternative tappings) Side/Rear Ports of your choice - see page 46 for options. Please specify your port choice when ordering. SP Length of Standard End over Length of Standard End over: 25.7mm SP Seal Kit Ordering ode 5SALG SP Shaft Seals All pumps fitted with high temperature nitrile shaft seals (110 c intermittent). 44

19 click here to return to front page SP Pump Selection - Shafts and Mounting Flanges SP Shaft Type ø Full Spline exact at this point 10.4 max. M14 x K4 1:5 Taper with M14 x 5mm thread and 4mm wide key Torque Rating - 1 Nm Q5 SAE 11 Tooth Spline Torque Rating Nm S2 SAE 13 Tooth Spline Torque Rating Nm T2 1:8 Taper Torque Rating - 1 Nm SP Mounting Flange Type ø typ N82 Nihon Spindle S2 SAE 2 olt max. SA2 SAE A 2 olt X50 Italian/European 4 olt 50.8 Pilot ø ø95 T1 Perkins 1000 Series DIN - 4 olt 100mm Pilot 45

20 click here to return to front page SP Pump Selection - Ports SP Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 44) x 66.4 mm SP SP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 ø48.1 ø25.4 ø48.1 ø19 inlet outlet 2PL Dowty - 5/16-18 UN Tappings (M8) ø Size (Ax) Tapping European Diamond (metric) Exceptions 12 x 26 M5 13 x 30 M6 19 x 40 M8 27 x 51 M10 19x56 M10 27x56 M and above only ø Size (Ax) Tapping 8 x 26 M5 10 x 26 M5 13 x 30 M6 15 x 35 M6 20 x 40 M6 18 x 55 M8 26 x 55 M8 European Square (metric) M8 x 1.25 tapped HPI Size Exceptions A and above ø Size (Ax) 5/8 x 36 7/8 x 48 Japanese Diamond JSP JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 Metric Metric Size 14 x x x x x x 2 30 x x 2 42 x 2 NPT NPT Size 1/8 x 28 1/4 x 18 3/8 x 18 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 SAE Size 7/16 x 20 1/2 x 20 9/16 x 18 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x /8 x /2 x 12 SAE 'O' Ring SAE Flange A Tapping Metric Tapping UN 1/2" M8 x /16" - 18 UN 3/4" M10 x 1.5 3/8" - 16 UN 1" M10 x 1.5 3/8" - 16 UN 1 1/4" M10 x 1.5 3/8" - 16 UN 1 1/2" M12 x /2" - 13 UN 2" M12 x /2" - 13 UN SAE Split Flange - 1/2, 3/4" and 1" available in vertical position 46

21 click here to return to front page PGP502 Pump Selection - Ordering ode, Seal Kits and Specifications PGP502 - Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAP2 016 P2 D1 A V W (1.69 cc/rev, P2 Shaft, D1 Flange, front pump, side ports, viton seal, anti-clockwise) PAP2 016 P2 D1 N W (1.69 cc/rev, P2 Shaft, D1 Flange, single pump, side ports, blank back cover, viton seal, anti-clockwise) PAP2 016 P2 D1 P V W (1.69 cc/rev, P2 Shaft, D1 Flange, single pump, side or rear ports, portable back cover, viton seal, clockwise rotation) PAP2 033 A (3.3cc/rev capacity, centre section, side ports only, section with drive for another pump) PAP2 033 E (3.3cc/rev capacity, back section, side ports only, blank back cover) PAP2 033 P (3.3cc/rev capacity, back section, side and/or rear ports, portable back cover) Front/Single Pump entre/ack Section PAP2 *** $$?? &&! ### PAP2 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 48?? Mounting Flange see codes in purple boxes under flange diagrams on page 49 && Model/Features A P front pump single pump single pump! Shaft Seal N V Nitrile Viton side ports only front section side ports only blank back cover (not portable) side or rear ports portable back cover # Rotation W Anti-lockwise W lockwise *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model/Features A E P side ports only centre section with section drive for another pump back side ports only section land back cover (not portable) back side or rear ports section portable back cover PGP502 - Specifications Pump Model Displacement cc/rev in3/rev ontinuous Pressure bar psi Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Max speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Weight kg Length End over mm Length of ody mm Length of Sealed Section mm PGP502 - Ports (all flange ports available with alternative tappings) Ports of your choice - see page 49 for options. Please specify your port choice when ordering. PGP502 - Seal Kit Ordering ode For a front or single pump: PAP2SK For a centre or back section: PAP2/RSK 47

22 click here to return to front page PGP502 Pump Selection - Flange and Shaft ombinations and Shafts PGP502 - Shaft Type Key 2.5 x Key 2.4 x 5 ø Key 2x 2, 6-D7 ø0.4 ø10 ø : nut M6 washer P3 (1) 1:8 Taper 2x2.6 Woodruff key Torque Rating - 30 Nm ø : nut M6 washer P2 (2) 1:8 Taper 2.4x5 Woodruff key Torque Rating - 30 Nm 1:5 nut M6 washer 6 P1 (3) 1:5 Taper 2x2.6 Woodruff key Torque Rating - 30 Nm 5 e9 ø5.3 V2 (K1) Short Tang/Spade Torque Rating - 22 Nm 12 5 e9 ø V1(K2) Long Tang/Spade Torque Rating - 22 Nm 30.3 key 3h9x3x22 SN H1(V1) 10mm Parallel 3x3x22 key Torque Rating - 30 Nm Maximum torque transmission capability of PGP2-PGP2 connecting shafts: 20 Nm PGP502 - Possible ombination of Flanges and Shafts Flange Design Drive Shafts D1 (R1) H1 (S1) P4 (A1) P1 (A2) A3 A4 P7 (A7) P3 (1) P2 (2) P1 (3) V2 (K1) V1 (K2) H1 (V1) 3 3 PGP502 - Mounting Flange Type x 2 'O' Ring x 2 'O' Ring x ø8.7 P4 (A1) 40mm x 40mm powerpack mount sealed shaft with outlet (clockwise rotation shown) ø32 f ø32 f x ø P1 (A2) 40mm x 40mm powerpack mount sealed shaft with outlet (clockwise rotation shown) 2 2x ø x 2 'O' Ring 14 A3 40mm x 40mm unsealed shaft 7 ø32 f x ø A4 40mm x 40mm sealed shaft for long Tang/Spade 7 ø32 f x 2 'O' Ring x ø P7 (A7) 40mm x 40mm powerpack mount unsealed shaft with Inlet ø32 f ø25.4 f8 4x ø 7.2 D1 (R1) Italian / European Group 1, 4 olt H1 (S1) SAE AA, 2 olt ø50.8 f8 48

23 click here to return to front page PGP502 Pump Selection - Mounting Flanges and Ports PGP502 - Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 47) x 30.7 mm SP Size 1/8 x 28 1/4 x 19 3/8 x 19 ø Size (Ax) Tapping 8 x 26 M5 10 x 26 M5 13 x 30 M6 Size A M6 x 1 tapped SP European Square (metric) HPI (4.8cc and above only) 38.1 JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 Metric Size 14 x x x x 1.5 SAE Size 9/16 x 18 3/4 x ø1/2 M8 x 1.25 tapped JSP Metric SAE 'O' Ring SAE Split Flange (4.8cc and above only) PGP502 Relief Valves PGP502 Relief Valves - Ordering ode Ordering ode Valve Setting Pressure Range Internal Drain External Drain PAP5IRVLP bar ( psi) 3 PAP5ERVLP bar ( psi) 3 PAP5IRVHP bar ( psi) 3 PAP5ERVHP bar ( psi) 3 PAP11IRVMP bar ( psi) 3 PAP11ERVMP bar ( psi) 3 When built into single pumps use in conjunction with PAP2***$$????AV. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAP2***A. PGP502 Relief Valves - Specifications Range Six options, all fully adjustable across their pressure ranges. Internal Drain Relief outlet drains into the inlet side of the pump. External Drain Relief outlet drains to tank. Length 28mm External Drain Port 9/16 SAE 'O' Ring 49

24 click here to return to front page PGP505 Pump Selection - Ordering ode, Seal Kits and Specifications PGP505 - Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAP5 A 020 J1L SAA2 AV (75mm wide, 2.0cc/rev capacity, J1L shaft, SAA2 flange, front pump/section, side ports only, viton seal) PAP5 A 020 J1L SAA2 V (75mm wide, 2.0cc/rev capacity, J1L shaft, SAA2 flange, single pump, side ports only, blank back cover, viton seal) PAP5 A 020 J1L SAA2 PV (75mm wide, 2.0cc/rev capacity, J1L shaft, SAA2 flange, single pump, side or rear ports, portable back cover, viton seal) PAP5 A 020 A (75mm wide, 2.0cc/rev capacity, centre section, side ports only, section with drive for another pump) PAP5 A 020 E (75mm wide, 2.0cc/rev capacity, back section, side ports only, blank back cover) PAP5 A 020 P (75mm wide, 2.0cc/rev capacity, back section, side or rear ports, portable back cover) Front/Single Pump PAP5! *** $$$???? && entre/ack Section PAP5! *** &&! ody Width A 75mm 66mm *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$ Shaft see codes in purple boxes under shaft diagrams on page 51???? Mounting Flange see codes in purple boxes under flange diagrams on page 52 && Model/Features AV V PV front pump single pump single pump side ports only front section viton seal side ports only blank back cover (not portable) viton seal side or rear ports portable back cover viton seal! ody Width A 75mm 66mm *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model/Features A E P centre section side ports only section with drive for another pump back side ports only section blank back cover (not portable) back side or rear ports section portable back cover PGP505 - Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw ody Length mm PGP505 - Ports (all flange ports available with alternative tappings) Ports of your choice - see page 53 for options. Please specify your port choice when ordering. PGP505 - Lengths Length of Standard End over (E): 17mm Length of Portable End over (P): 27mm Length of entre Plate: 5mm PGP505 - Seal Kit Ordering ode For a front or single pump: PAP5SK For a centre or back section: PAP5/RSK 50

25 click here to return to front page PGP505 Pump Selection - Shafts PGP505 - Shaft Type 32 with SA2 27 with SAA with SAA with A with X36 ø12.7 ø12.7 ø13.45 A1 5/8" SAE A, 9 Tooth Spline Torque Rating Nm 26.9 with SAA2 A2 1/2" SAE AA, 9 Tooth Spline Torque Rating Nm 38.1 with SA2 J1 1/2" SAE AA, Parallel Torque Rating - 43 Nm 38.1 with A1 J1L 1/2" SAE AA, Parallel (long for A1 & A2A1 flanges) Torque Rating - 43 Nm 31.8 with SA2 J mm Parallel Torque Rating - 52 Nm 34.7 with X ø12.7 ø14.3 ø14.3 ø M8 x 1.25 J3 1/2" Parallel Torque Rating - 43 Nm J4 9/16" Parallel Torque Rating Nm J4L 9/16" Parallel (long for A1 & A2A1 flanges) Torque Rating Nm K1 SAE A Parallel Torque Rating - 85 Nm Q1 1:8 Taper Torque Rating - 43 Nm 35 with D2 10 Q2 1:8 Taper Torque Rating - 68 Nm M10 x 1 with A V7 6.35mm Tang/Spade Drive Torque Rating - 31 Nm ø with A1 7.9 V9 4.3mm Tang/Spade Drive Torque Rating - 16 Nm ø Maximum torque transmission capability of PGP505 - PGP505 connecting shafts: 36Nm 51

26 click here to return to front page PGP505 Pump Selection - Mounting Flanges PGP505 - Mounting Flange Type ø ø30 ø8.7 ø45.25 ø8.7 ø45.25 A1 2 x 2 4 olt Shallow Shaft Seal A2A1 2 x 2 4 olt Deep Shaft Seal D2 Italian/European 4 olt 30mm Pilot ø ø ø34.8 ø82.55 ø9 JSP Jacobsen 2 olt MP Rear Section Modular Front SA2 SAE 2 olt ø SA2H SAE 2 olt helsea ø SA2SL SAE 2 olt Slotted SA2W SAE 2 olt Wet Mount ø ø10.3 ø50.8 ø50.8 ø ø36.5 SAA2 SAE AA 2 olt (not suitable for A ody) SAA2W SAE AA 2 olt Wet Mount X36 Italian/European 4 olt 52

27 click here to return to front page PGP505 Pump Selection - Ports PGP505 - Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 50) x 33.7 mm SP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x ø15 ø Size (Ax) Tapping 12 x 26 M5 13 x 30 M6 SP OPL Dowty - 1/4" - 20 UN Tapping (M6) European Diamond (metric) ø Size (Ax) Tapping 8 x 26 M5 10 x 26 M5 13 x 30 M6 15 x 35 M6 20 x 40 M8 Exceptions 050 and above only Size A M M6 Tapping JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 European Square (metric) HPI (7cc and above only) JSP Metric Size 14 x x x x 1.5 NPT Size 3/8 x 18 SAE Size 9/16 x 18 3/4 x 16 7/8 x /16 x 12 Metric NPT SAE 'O' Ring SAE Flange A Tapping Tapping Metric UN Exceptions 1/2" M8 x /16" and 18 UN above only SAE Split Flange (7cc and above only) 53

28 click here to return to front page PGP505 Relief Valves PGP505 Relief Valves - Ordering ode Use this chart to compile your ordering code - e.g. PAP5 I RVLP (Relief Valve with pressure range of bar / psi and internal drain). PAP5 $????? $$ Drain I Internal Drain E External Drain???? Valve Setting Pressure Range RVLP bar ( psi) RVHP bar ( psi) RVSUN bar ( psi) If used in conjunction with a pump that is the back section of a multiple unit, use pump order code PAP5!***A. PGP505 Relief Valves - Specifications Range Six options, all fully adjustable across their pressure ranges. Internal Drain Relief outlet drains into the inlet side of the pump. External Drain Relief outlet drains to tank. Length 28mm External Drain Port 9/16" SAE O Ring We can arrange airfreight or sea freight despatch to any country in the world. Request a quote now. 54

29 click here to return to front page PGP511 Pump Selection - Ordering ode, Seal Kits and Specifications PGP511 - Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAP A1 SA2 A V (8.0cc/rev capacity, 0A1 shaft, SA2 flange, front pump/section, side ports only, viton seal) PAP S1 L1 N (12.0cc/rev capacity, J1L shaft, SAA2 flange, single pump, side ports only, blank back cover, nitrile seal) PAP S4 X36 P E (10.0cc/rev capacity, J1L shaft, X36 flange, single pump, side or rear ports, portable back cover, 2 x nitrile seals) PAP A (8.0cc/rev capacity, centre section, side ports only, section with drive for another pump) PAP E (8.0cc/rev capacity, back section, side ports only, blank back cover) PAP P (8.0cc/rev capacity, back section, side or rear ports, portable back cover) Front/Single Pump entre/ack Section PAP11 *** $$???? &! PAP11 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 56???? Mounting Flange see codes in purple boxes under flange diagrams on pages 57 and 58 && Model/Features A P front pump single pump single pump! Shaft Seal N Nitrile Seal V Viton Seal E 2 x Nitrile Seals W 2 x Viton Seals side ports only front section side ports only blank back cover (not portable) side or rear ports portable back cover *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model/Features A E P centre section back section back section side ports only section with drive for another pump side ports only blank back cover (not portable) side or rear ports portable back cover PGP511 - Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw ody Length mm PGP511 - Ports (all flange ports available with alternative tappings) Ports of your choice - see page 59 for options. Please specify your port choice when ordering. PGP511 - Lengths Standard End over (E): 21mm Portable End over (P): 30mm Unsealed entre Plate: 5.8mm Sealed entre Plate Pair: 31mm PGP511 - Seal Kit Ordering ode For a front or single pump with side and/or rear ports: Nitrile Seal Kit - UP1PXA02N, Viton Seal Kit - UP1PXA02V For Pumps with 1, 2, L5 & L8 Shafts: UP1PXA02N(3/4) For a centre or back section with side and/or rear ports: UP1PXA04 55

30 click here to return to front page PGP511 Pump Selection - Shafts PGP511 - Shaft Type 32 with SA2 32 with SA with SA with SA2 23 with 80 A1 5/8" SAE A, 9 Tooth Spline Torque Rating - 86 Nm 1 11/16" SAE, 10 Tooth Spline Torque Rating Nm 1 3/4" SAE, 11 Tooth Spline Torque Rating Nm 2 3/4" SAE, 11 Tooth Spline Torque Rating Nm F1 9 Tooth DIN 5482 Spline (not available for 25cc/rev pump model) Torque Rating Nm 24 with with SA with SA with X36 ø ø /16-20 UNF F2 13 Tooth DIN 5480 Spline Torque Rating Nm K4 5/8" Long SAE A Parallel Torque Rating - 75 Nm K7 5/8" SAE A Parallel Torque Rating - 75 Nm L1 Dowty Parallel Torque Rating Nm with SA2 ø with SA2 ø with SA2 ø19.05 ø with 80 M12 x 1.5 L2 5/8" SAE A Parallel Torque Rating Nm L5 3/4" SAE Parallel Torque Rating Nm L8 3/4" SAE Long Parallel Torque Rating Nm S1 DIN 1:5 Taper Torque Rating Nm 39.7 with X36 ø18 ø17.5 ø19 M12 x 1.5 with L with L with L1 8 S4 European 1:8 Taper Torque Rating Nm V5 Tang/Spade Torque Rating - Nm V6 Tang/Spade Torque Rating - 75 Nm Maximum torque transmission capability of PGP511 - PGP511 connecting shafts: 110Nm V8 Tang/Spade Torque Rating - 75 Nm 56

31 click here to return to front page PGP511 Pump Selection - Mounting Flanges PGP511 - Mounting Flange Type 50.8 ø ø ø ø ø80 A1 2 x 2 4 olt Shallow Shaft Seal A2 Perkins 100 Series Supplied with External Gear on 'S4' Shaft 80 DIN (osch) 4 olt ø ø ø ø ø75 95 ø ontinental DIN (osch) 4 olt E3 Valtra 4 olt F Dowty GP2 ø ø ø ø52 ø ø52 H5 SAE A 2 olt Slotted to take Large Shaft Seal H8 104mm x 52mm 2 olt H 52mm Pilot 4 Through olt 72 ø ø ø ø36.4 ø50 ø52 K1 Rear Section Front Flange L1 Deutz Engine 2 olt with 50mm Pilot LU 52mm Pilot 2 Through olt (Left) 57

32 click here to return to front page PGP511 Pump Selection - Mounting Flanges continued PGP511 - Mounting Flange Type ø ø52 ø50 ø52 ø10.7 ø10.7 MP Modular Rear Section Front Flange R1 International Harvester (IH) 2 olt RU 52mm Pilot 2 Through olt (Right) ø11.2 ø11.2 M10 ø82.55 ø82.55 ø82.55 SA2 SAE A 2 olt SA2LS SAE A 2 olt to take Large Seal SA2M SAE A 2 olt M10 Tappings ø ø ø ø101.6 ø ø95 SA2S SAE A 2 olt Slotted S2 SAE 2 olt T1 Perkins 1000 Series Supplied with 28 Tooth External Gear on 'S4' Shaft ø9 30 ø ø ø ø98.4 ø10.7 ø82.55 T2 Perkins 4 olt T3 Perkins 1000 Series with Tell Tale Drain Supplied with 28 Tooth External Gear on 'S4' Shaft X36 Italian/European 4 olt HT - HT helsea 82.55mm through bolt 58

33 click here to return to front page PGP511 Pump Selection - Ports PGP511 - Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 55) x 49 mm SP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x ø Size (Ax) Tapping 12 x 26 M5 13 x 30 M6 19 x 40 M8 27 x 51 M10 19 x 56 M10 27 x 56 M10 32 x 62 M10 Exceptions 0 and above only SP 1PL Dowty - 5/16-18 UN Tappings (M8) European Diamond (metric) Size (Ax) Tapping ø 8 x 26 M5 10 x 26 M5 13 x 30 M6 15 x 35 M6 20 x 40 M6 18 x 55 M8 26 x 55 M8 M6 x 1 tapped Size A M M M6 Tapping ø Size (Ax) 5/8 x 36 7/8 x 48 European Square (metric) HPI Japanese Diamond JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 1 x 14 1 x /4 x 11 Metric Size 14 x x x x x x 2 33 x 2 NPT Size 1/8 x 27 1/4 x 18 3/8 x 18 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 JSP Metric NPT SAE Size 7/16 x 20 1/2 x 20 9/16 x 18 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x 12 SAE Flange A Tapping Metric Tapping UN 1/2" M8 x /16" - 18 UN 3/4" M10 x 1.5 3/8" - 16 UN 1" M10 x 1.5 3/8" - 16 UN SAE 'O' Ring SAE Split Flange - 1/2 available in vertical position 59

34 click here to return to front page PGP511 ontinental/earing Supported Drives These subassemblies are used when an inbuilt bearing supported shaft is required, such as for pulley driven pumps or when a one piece shaft is not available. PGP511 ontinental/earing Supported Drives - Ordering ode Use this chart to compile your ordering code. For example: PAP11 D1 SA2-SA2 (D1 shaft, SA2-SA2 flange) PP11DS D1 (D1 shaft) PP11MSE SA2-SA2 (SA2-SA2 flange) Subassembly Shaft Flange PAP11 $$?????-?????? PP11DS $$ PP11PSE???? $$ Shaft see codes in purple boxes under shaft diagrams below $$ Mounting Flange see codes in purple boxes under flange diagrams below $$ Shaft see codes in purple boxes under shaft diagrams below $$ Mounting Flange see codes in purple boxes under flange diagrams below If being used as part of a single pump, use with PGP511 pump assembly PAP11***E or PAP11***P. If being used as the drive for a multiple pump, use in conjunction with PAP11***A which becomes the front pump section. PGP511 ontinental/earing Supported Drives - Shafts /2" UNF M12 x 1.5 M12 x 1.5 with S2 D1 7/8 SAE, 13 Tooth Spline, Torque Rating Nm R7 3/4 SAE 1.8 Taper, Torque Rating Nm ø S4 European 1:8 Taper, Torque Rating Nm M12 x Stand out with SA2 ø S8L4 DIN 1.5 Taper, Torque Rating Nm Z3 1 1/4 SAE, 14 Tooth Spline, Torque Rating Nm M12 x 1.5 M1 7/8 SAE, Parallel, Torque Rating Nm S8 1.5 Taper, Torque Rating Nm 1 3/4 11 Tooth Spline Torque Rating Nm S1 DIN 1:5 Taper, Torque Rating Nm PGP511 ontinental/earing Supported Drives - Mounting Flanges ø11.2 ø11.2 ø ø ø36.5 SA2 - SA2 SAE A 2 olt ø82.55 ø82.55 SA2L4 - SA2L4 SAE A 2 olt outboard bearing, only with S8L4 shaft 2 - S2 SAE 2 olt ø101.6 X36 - X36 Italian/European 4 olt

35 click here to return to front page PGP511 Relief Valves PGP511 Relief Valves - Ordering ode Use this chart to compile your ordering code - e.g. PAP11 I RVLP (Relief Valve with pressure range of 7-70 bar / psi and internal drain). PAP11 $????? $$ Drain I Internal Drain E External Drain???? Valve Setting Pressure Range RVLP 7-70 bar ( psi) RVHP bar ( psi) RVSUN bar ( psi) RVMP bar ( psi) When built into single pumps use in conjunction with PAP11***$$????A!. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAP11***A. PGP511 Relief Valves - Specifications Range Six options, all fully adjustable across their pressure ranges. Internal Drain Relief outlet drains into the inlet side of the pump. External Drain Relief outlet drains to tank. Length 30mm External Drain Ports SP up to 1/2 SAE O Ring up to 3/4 Metric up to 20mm PGP511 Pumps with Priority Flow ontrol and Relief Valve Assemblies PGP511 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Ordering ode Use this chart to compile your ordering code - e.g. PAP11PPF 03 (pump with a flow control setting of 3 l/min / 0.66 gpm). PAP11PPF $$ $$ Flow ontrol Setting Relief Valve Adjustment Range 03 3 l/min (0.66 gpm) bar ( psi) 06 6 l/min (1.32 gpm) bar ( psi) 09 9 l/min (2 gpm) bar ( psi) l/min (2.64 gpm) bar ( psi) When built into single pumps use in conjunction with PAP11***$$????A!. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAP11***A. PGP511 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Specifications Relief Valve Requirements Priority flow is pressure compensated, bypass port pressure can exceed priority pressure. The inbuilt relief valve acts on the priority line and drains into the inlet of the pump. The bypass port line, if not draining to tank, requires an external relief valve to protect it. Length 66.4 mm Port (side or rear) Priority - 3/4" SAE O Ring Secondary - 7/8" SAE O Ring 61

36 click here to return to front page PGP517 Pump Selection - Ordering ode, Seal Kits and Specifications PGP517 - Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAP T1 X50 A V (33.0cc/rev capacity, T1 shaft, X50 flange, front pump/section, side ports only, viton seal) PAP17 1 T1 X50 W (16.0cc/rev capacity, T1 shaft, X50 flange, single pump, side ports only, blank back cover, wet mount seal) PAP M2 S2 P V (14.0cc/rev capacity, M2 shaft, S2 flange, single pump, side or rear ports, portable back cover, viton seal) PAP A (19.0cc/rev capacity, centre section, side ports only, section with drive for another pump) PAP E (19.0cc/rev capacity, back section, side ports only, blank back cover) PAP P (19.0cc/rev capacity, back section, side or rear ports, portable back cover) Front/Single Pump entre/ack Section PAP17 *** $$???? &! PAP17 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 63???? Mounting Flange see codes in purple boxes under flange diagrams on page 63 && Model/Features A P front pump single pump single pump! Shaft Seal V Viton Seal W Wet Mount Seal side ports only front section side ports only blank back cover (not portable) side or rear ports portable back cover *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model/Features A E P centre section back section back section side ports only section with drive for another pump side ports only blank back cover (not portable) side or rear ports portable back cover PGP517 - Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw ody Length mm PGP517 - Ports (all flange ports available with alternative tappings) Ports of your choice - see page 64 for options. Please specify your port choice when ordering. PGP517 - Lengths Standard End over (E): 26mm Portable End over (P): 33mm Unsealed entre Plate: 5.8mm Sealed entre Plate Pair: 42mm PGP517 - Seal Kit Ordering ode For a front or single pump: PAP17SK For a centre or back section: PAP17/RSK 62

37 click here to return to front page PGP517 Pump Selection - Mounting Flanges and Shafts PGP517 - Shaft Type with SA2 with SA2 with S2 with S2 with S2 1 11/16 SAE, 10 Tooth Spline Torque Rating Nm 1 3/4 11 Tooth Spline Torque Rating Nm D1 7/8 SAE, 13 Tooth Spline Torque Rating Nm E1 1 SAE, 15 Tooth Spline Torque Rating Nm M2 1 SAE, Parallel Torque Rating Nm with X50 with 105 with S2 with S2 with S2 M14 x M16 x D1L 7/8 SAE, 13 Tooth Spline Torque Rating Nm M5 7/8 SAE, Parallel Torque Rating Nm M7 7/8 SAE Parallel Long Torque Rating Nm T1 European 1:8 Taper Torque Rating Nm T2 DIN 1:5 Taper Torque Rating Nm Maximum torque transmission capability of PGP517 - PGP517 connecting shafts: 228Nm PGP517 - Mounting Flange Type ø11 28 ø ø11 28 ø ø11 38 ø DIN 4 olt 100mm Pilot 105 DIN 4 olt (osch) 105mm Pilot SA2 SAE A 2 olt (for M7 & D1L shafts only) 78 ø ø ø51.9 ø14.3 ø ø50.77 MP Rear Section Modular Front S2 SAE 2 olt X50 Italian/European 4 olt 63

38 click here to return to front page PGP517 Pump Selection - Ports PGP517 - Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 62) x 68.5 mm SP SP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 ø48.1 ø25.4 ø48.1 ø19 inlet outlet 2PL Dowty (5/16-18 UN Tappings (M8)) ø Size (Ax) Tapping 12 x 26 M5 13 x 30 M6 19 x 40 M8 27 x 51 M10 19 x 56 M10 27 x 56 M10 32 x 62 M10 38 x 72 M10 European Diamond (metric) ø Size (Ax) Tapping 8 x 26 M5 10 x 26 M5 13 x 30 M6 15 x 35 M6 20 x 40 M6 18 x 55 M8 26 x 55 M8 M8 x 1.25 tapped Size A European Square (metric) HPI Japanese Diamond ø Size (Ax) 5/8 x 36 7/8 x 48 JSP JSP Size 1/8 x 28 1/4 x 19 3/8 x 19 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 Metric Metric Size 14 x x x x x x 2 30 x x 2 42 x 2 NPT NPT Size 1/8 x 27 1/4 x 18 3/8 x 18 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 SAE Size 7/16 x 20 1/2 x 20 9/16 x 18 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x /8 x /2 x 12 SAE Flange A Tapping Metric Tapping UN 1/2" M8 x /16" - 18 UN 3/4" M10 x 1.5 3/8" - 16 UN 1" M10 x 1.5 3/8" - 16 UN 1 1/ M10 x 1.5 3/8" - 16 UN 1 1/ M12 x /2" - 13 UN M12 x /2" - 13 UN SAE 'O' Ring SAE Split Flange - 1/2, 3/4" and 1" available in vertical position 64

39 click here to return to front page PGP517 ontinental/earing Supported Drives These subassemblies are used when an inbuilt bearing supported shaft is required, such as for pulley driven pumps or when a one piece shaft is not available. PGP517 ontinental/earing Supported Drives - Ordering ode Use this chart to compile your ordering code. For example: PAP17 D1 SA2 (D1 shaft, SA2 flange) PP17DS D1 (D1 shaft) PP17PSE S2 (S2 flange) Subassembly Shaft Flange PAP17 $$???? PP17DS $$ PP17PSE???? $$ Shaft see codes in purple boxes under shaft diagrams below $$ Mounting Flange see codes in purple boxes under flange diagrams below $$ Shaft see codes in purple boxes under shaft diagrams below $$ Mounting Flange see codes in purple boxes under flange diagrams below If being used as part of a single pump, use with PGP517 pump assembly PAP17***E or PAP17***P. If being used as the drive for a multiple pump, use in conjunction with PAP17***A which becomes the front pump section. PGP517 ontinental/earing Supported Drives - Shafts Stand out with S2 33 Stand out with S2 Stand out with S2 D1 7/8 SAE, 13 Tooth Spline Torque Rating Nm Stand out with S2 M1 7/8 SAE, Parallel Torque Rating Nm Stand out with S2 M2 1 SAE, Parallel Torque Rating Nm PGP517 ontinental/earing Supported Drives - Mounting Flanges Stand out with S2 M7 7/8 SAE Long Parallel Torque Rating Nm 5/8" UNF R3 7/8 SAE, 1:8 Taper Torque Rating Nm Z3 1 1/4 14 Tooth Spline Torque Rating Nm ø11 ø14.3 ø82.55 ø101.6 SA2 SAE A 2 olt S2 SAE 2 olt 65

40 click here to return to front page PGP517 Relief Valves PGP517 Relief Valves - Ordering ode Use this chart to compile your ordering code - e.g. PAP17 I RVLP (Relief Valve with pressure range of bar / psi and internal drain). PAP17 $????? $$ Drain I Internal Drain E External Drain???? Valve Setting Pressure Range RVLP bar ( psi) RVHP bar ( psi) When built into single pumps use in conjunction with PAP17***$$????A!. If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAP17***A. PGP517 Relief Valves - Specifications Range Four options, all fully adjustable across their pressure ranges. Internal Drain Relief outlet drains into the inlet side of the pump. External Drain Relief outlet drains to tank. Length 30mm External Drain Ports SP up to 1/2 SAE O Ring up to 3/4 Metric up to 20mm PGP517 Pumps with Priority Flow ontrol and Relief Valve Assemblies PGP517 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Ordering ode Use this chart to compile your ordering code - e.g. PAP17PPF 03 (pump with a flow control setting of 3 l/min / 0.66 gpm). PAP17PPF $$ When built into single pumps use in conjunction with PAP17***$$????A! If used in conjunction with a pump that either has a continental/bearing supported drive on the front or is the back section of a multiple unit, use pump order code PAP17***A. $$ Flow ontrol Setting Relief Valve Adjustment Range 03 3 l/min (0.66 gpm) bar ( psi) 07 7 l/min (1.54 gpm) bar ( psi) l/min (2.42 gpm) bar ( psi) l/min (3.30 gpm) bar ( psi) l/min (4.18 gpm) bar ( psi) l/min (5.07 gpm) bar ( psi) l/min (5.95 gpm) bar ( psi) l/min (6.83 gpm) bar ( psi) l/min (7.71 gpm) bar ( psi) l/min (8.59 gpm) bar ( psi) l/min (9.47 gpm) bar ( psi) PGP517 Pumps with Priority Flow ontrol and Relief Valve Assemblies - Specifications Relief Valve Requirements Priority flow is pressure compensated, bypass port pressure can exceed priority pressure. The inbuilt relief valve acts on the priority line and drains into the inlet of the pump. The bypass port line, if not draining to tank, requires an external relief valve to protect it. Length 76 mm Port Inlet Rear - 1 5/8" SAE 'O' Ring Priority - 3/4" SAE O Ring (side or rear) Secondary - 1 1/16" SAE O Ring (side or rear) 66

41 click here to return to front page PGP620 Pump Selection - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAP62 A 330 T1 A3 A V (anti-clockwise rot., 33.0cc/rev cap., T1 shaft, A3 flange, front pump/section, side ports only, viton seal) PAP62 A 410 T1 A3 V ( anti-clockwise rotation, 41.0cc/rev capacity, T1 shaft, A3 flange, single pump, side and/or rear ports, portable back cover, viton seal) PAP A (19.0cc/rev capacity, centre section, side ports only, section with drive for another pump) PAP E (19.0cc/rev capacity, back section, side and/or rear ports, portable back cover) Front/Single Pump entre/ack Section PAP62 # *** $$?? &! PAP620 *** && # Rotation A Anti-lockwise lockwise *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 68?? Mounting Flange see codes in purple boxes under flange diagrams on page 68! Shaft Seal N Single Nitrile V Single Viton M Double Nitrile W Double Viton & Model and Features A front pump side ports only front section single pump side and/or rear ports portable back cover Y front pump Piggy back front section side ports (see page 70) *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model and Features A E centre section back section side ports only section with drive for another pump side and/or rear ports portable back cover Specifications Pump Model Displacement Max ontinuous Pressure Max Intermittent Pressure cc/rev in3/rev bar psi bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw ody Length (single unit) mm ody Length (multiple unit) mm Weight kg Ports (all flange ports available with alternative tappings) Ports of your choice - see page 69 for options. Please specify your port choice when ordering. Seal Kit Ordering ode For a single/front pump with Nitrile 'N' and 'M' Seals: UP2PRA01N For a single/front pump with Viton V and W Seals: UP2PRA01V For a centre/back section pump with Nitrile 'N' and 'M' Seals: UP2PRA02N For a centre/back section pump with Viton V and W Seals: UP2PRA02V 67

42 click here to return to front page PGP620 Pump Selection - Shafts and Mounting Flanges PGP620 Shaft Type square key: 6.3 x 6.3 x /4 SAE, 11 Tooth Spline Torque Rating Nm D1 7/8 SAE, 13 Tooth Spline Torque Rating Nm E1 1 SAE, 15 Tooth Spline Torque Rating - 4 Nm M3 1 SAE Keyed Parallel Torque Rating Nm for size 2 only rect. key: 8 x 7 x 55 square key: 4.8 x 4.8 x M14 x M16 x 1.5 M4 25mm Keyed Parallel, Torque Rating Nm (for size 2 only) M1 7/8 unthreaded Keyed Parallel Torque Rating Nm T1 European 1:8 Taper Torque Rating Nm Maximum Torque Transmission capability of PGP620 - PGP620 onnecting Shafts = 228NM T2 European 1:5 Taper Torque Rating Nm PGP620 Mounting Flange Type 9.4 ø ø14.3 A3 SAE 4 olt ø A4 SAE 4 olt ø ø D7 Italian/European Pilot, 4 olt ø H2 SAE A 2 olt 132 max ø ø H3 SAE 2 olt max ø M8 x deep holes at ø ø T7 Perkins 1000 Series

43 click here to return to front page PGP620 Pump Selection - Ports Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 67) x 73.6 mm SP Size 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 ø48.1 ø25.4 ø48.1 ø19 inlet outlet ø Size (Ax) Tapping 12 x 26 M5 13 x 30 M6 19 x 40 M8 27 x 51 M10 19 x 56 M10 27 x 56 M10 32 x 62 M10 38 x 72 M10 SP Dowty (5/16-18 UN Tappings (M8)) European Diamond (metric) ø Size (Ax) Tapping 13 x 30 M6 15 x 35 M6 20 x 40 M6 18 x 55 M8 26 x 55 M8 Size A ø Size (Ax) 5/8 x 36 7/8 x 48 M8 x 1.25 tapped European Square (metric) HPI Japanese Diamond JSP Size 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 Metric Size 18 x x x x 2 30 x x 2 42 x 2 NPT Size 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 JSP Metric NPT SAE Size 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x /8 x /2 x 12 SAE Flange A Tapping Metric Tapping UN 1/2" M8 x /16" - 18 UN 3/4" M10 x 1.5 3/8" - 16 UN 1" M10 x 1.5 3/8" - 16 UN 1 1/ M10 x 1.5 3/8" - 16 UN 1 1/ M12 x /2" - 13 UN M12 x /2" - 13 UN SAE 'O' Ring SAE Split Flange - 1/2, 3/4" and 1" available in vertical position 69

44 click here to return to front page PGP620 ontinental/earing Supported Drives These sub-assemblies are used when an inbuilt bearing supported shaft is required, such as for pulley driven pumps or when a one piece shaft is not available. Ordering ode Use this chart to compile your ordering code. For example: PAP620 A E1 M L3 (anti-clockwise, E1 shaft, multiple pump, L3 flange) PP620DS E1 (E1 shaft) Mounting Flange Type - L3 all measurements are in mm unless otherwise stated PAP620 # $$ M L3 # Rotation A Anti-lockwise lockwise Subassembly $$ Shaft see codes in purple boxes under shaft diagrams to right Shaft M Pump PP620DS $$ uilding PGP620/640 Double Pumps M Multiple Pump omit for single pump $$ Shaft see codes in purple boxes under shaft diagrams to right Tandem Front Section Ordering ode When sections have the same frame size, use a front section ending: A then N / V / M / W. Front Section PAP62 # *** $$?? A! + PAP620 *** E (page 67) PAP64 # *** $$?? A! + PAP640 *** E (page 71) 89.8 Shafts - PP620DS$$ L3 SAE 2 /4 olt with L3 9.4 E1 1" SAE 15 Tooth Spline Torque Rating Nm ø holes all measurements are in mm unless otherwise stated square key: 6.3 x 6.3 x M3 1" SAE Keyed Parallel Torque Rating Nm Piggyback Front Section Ordering ode When the Following Section is a smaller frame size than the Front Section, it is referred to as a Piggyback Pump. Use the Piggyback Front Section ending: Y then N / V / M / W. Please specify if common or separate inlets when ordering Front Section PAP62 # *** $$?? Y! + PAP11 *** E or P (pages ) PAP64 # *** $$?? Y! + PAP620 *** E (pages ) PAP64 # *** $$?? Y! + PAP11 *** E or P (pages ) 6.3 Tandem PAP (page 67) PAP (page 71) Piggyback PAP620 + PAP11 (pages ) PAP640 + PAP11 (pages ) PAP640 + PAP620 (pages ) 70

45 click here to return to front page PGP640 Pump Selection - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAP64 A 350 D1 A3 A V (anti-clockwise rotation, 35.0cc/rev capacity, D1 shaft, A3 flange, front pump/section, side ports only, viton seal) PAP64 A 450 E4 A3 V ( anti-clockwise rotation, 45.0cc/rev capacity, E4 shaft, A3 flange, single pump, side or rear ports, portable back cover, viton seal) PAP A (50.0cc/rev capacity, centre section, side ports only, section with drive for another pump) PAP E (50.0cc/rev capacity, back section, side or rear ports, portable back cover) Front/Single Pump entre/ack Section PAP64 # *** $$?? &! PAP640 *** && # Rotation A Anti-lockwise lockwise *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev 0.0 cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 72?? Mounting Flange see codes in purple boxes under flange diagrams on page 72 && Model/Features A front pump single pump! Shaft Seal N Single Nitrile V Single Viton M Double Nitrile W Double Viton side ports only front section side or rear ports portable back cover *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev 0.0 cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model/Features A E centre section back section side ports only section with drive for another pump side or rear ports portable back cover Specifications Pump Model Displacement Max ontinuous Pressure Max Intermittent Pressure cc/rev in3/rev bar psi bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw ody Length (single unit) mm ody Length (multiple unit) mm Weight (Single Unit) kg Ports (all flange ports available with alternative tappings) Ports of your choice - see page 73 for options. Please specify your port choice when ordering. Seal Kit Ordering ode For a single/front pump with Nitrile 'N' and 'M' Seals: PAP640SKN For a single/front pump with Viton V and W Seals: PAP640SKV For a centre/back section pump with Nitrile 'N' and 'M' Seals: PAP640SK1N For a centre/back section pump with Viton V and W Seals: PAP640SK1V 71

46 click here to return to front page PGP640 Pump Selection - Shafts and Mounting Flanges PGP640 Shaft Type D1 7/8 SAE, 13 Tooth Spline Torque Rating Nm 55.6 E1 1 SAE, 15 Tooth Spline Torque Rating Nm 55.6 square key: 8 x 8 x 38.1 ø (only with A4 and K3 flange) E4 SAE, 14 Tooth Spline Torque Rating - 9 Nm N1 1 1/4 SAE, Keyed Parallel Torque Rating Nm Maximum Torque Transmission capability of PGP640 - PGP640 onnecting Shafts = 407 Nm PGP640 Mounting Flange Type ø ø-14.3 A3 SAE 4 olt ø ø14.3 A4 SAE 4 olt max.5 ø ø H3 SAE 2 olt K3 SAE 2 olt 85 72

47 click here to return to front page PGP640 Pump Selection - Ports PGP640 Ports (all flange ports available with alternative tappings) Port Pad Size = ody Length (see Specification table on page 71) x 87.8 mm SP Size 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 ø48.1 ø25.4 ø48.1 ø19 inlet outlet ø Size (Ax) Tapping 12 x 26 M5 13 x 30 M6 19 x 40 M8 27 x 51 M10 19 x 56 M10 27 x 56 M10 32 x 62 M10 38 x 72 M10 SP Dowty (Dowty - 5/16-18 UN Tappings (M8)) European Diamond (metric) ø Size (Ax) Tapping 13 x 30 M6 15 x 35 M6 20 x 40 M6 18 x 55 M8 26 x 55 M8 Size A ø Size (Ax) 5/8 x 36 7/8 x 48 M8 x 1.25 tapped European Square (metric) HPI Japanese Diamond JSP Size 3/4 x 14 7/8 x 14 1 x /4 x /2 x 11 2 x 11 Metric Size 18 x x x x 2 30 x x 2 42 x 2 NPT Size 3/4 x 14 1 x 11 1/2 1 1/4 x 11 1/2 1 1/2 x 11 1/2 JSP Metric NPT SAE Size 3/4 x 16 7/8 x /16 x /16 x /16 x /8 x /8 x /2 x 12 SAE Flange A Tapping Metric Tapping UN 1/2" M8 x /16" - 18 UN 3/4" M10 x 1.5 3/8" - 16 UN 1" M10 x 1.5 3/8" - 16 UN 1 1/ M10 x 1.5 3/8" - 16 UN 1 1/ M12 x /2" - 13 UN M12 x /2" - 13 UN SAE 'O' Ring SAE Split Flange - 1/2, 3/4" and 1" available in vertical position 73

48 click here to return to front page David rown / Hydreco Q Series Pumps We can offer a very quick turnaround on David rown Q-Series pump (usually within 2-3 days). We can build to your exact specification, ideal for prototype projects or one-off requirements. Give us your specification from the following information, specify ports of your choice and we will build your high efficiency, low noise pump. QR Series Pump efficiencies compare with the very best spur gear pumps while noise generation is reduced to new low levels. QS Series helical gear pumps are for really noise critical applications. They retain the high efficiency levels of the QR series but generate even lower noise due to the pressure ripple reductions of up to 75%. Specifications David rown Series QR Series QS Series High pressure ratings bar (40 psi) 3 3 Wide speed range rev/min 3 3 Wide range of sizes cm3/rev (1 to 14.6 cu.in/rev 3 3 Very high efficiencies - up to 98% volumetric at 250 bar (3625 psi) 3 3 Long-life plain bearings 3 3 Up to 100 (212 F) operation 3 3 ompact size 3 3 Wide range of drives, mountings and ports 3 3 ast iron construction 3 3 Suitable for rigorous mobile applications 3 3 Multiple pumps on one shaft 3 3 Shared inlet ports on multiple pumps 3 3 Advanced spur gears for low noise levels 3 Patented helical gears for virtually silent operation 3 74

49 click here to return to front page David rown / Hydreco QR4 - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAR4 016 A SA2 V (16.0cc/rev capacity, A shaft, SA2 flange, single pump, blank back cover, A Design (single viton seal and wiper)) PAR4 032 S2W W (32.0cc/rev cap., shaft, S2W wet mount flange, single pump, blank back cover, Design (2 viton shaft seals, wiper and tell-tale)) PAR4 038 H S4 A V (38.0cc/rev capacity, H shaft, S4 flange, front section, A Design (single viton seal and wiper)) PAR4 045 Q S2W A W (32.0cc/rev capacity, Q shaft, S2W wet mount flange, front section, Design (2 viton shaft seals, wiper and tell-tale)) PAR4 053 A (53.0cc/rev capacity, centre section) PAR4 0 E (.0cc/rev capacity, rear section, blank end cover) Front Section/Single Pump entre/rear Section PAR4 *** $$$???? &! PAR4 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev 0.0 cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 77???? Mounting Flange See codes in purple boxes under flange diagrams on page 77. Flange codes ending with 'W' are for wet mount applications - pumps with two viton shaft seals (Shaft Seal code W). & Model/Features A front section single pump - blank back cover (not portable) Y Piggy back front section, side ports (see page 70)! Shaft Seal V W A Design: Single Viton Seal and wiper for external drives Design: Two viton shaft seals, inner and outer seal with tell-tale hole. The tell-tale hole indicates leakage before mixing of fluids can occur. *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev 0.0 cc/rev && Model A centre section E rear section - blank end cover (not portable) Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Single ody Length mm Intermediate ody Length mm Dimension A (see page 77 for drawing) mm Dimension (see page 77 for drawing) mm Dimension (see page 77 for drawing) mm Ports entre/onnection Kit Rotation Length of Shaft End over Ports of your choice - see pages 77 and 86 for options. Please specify your port choice when ordering. For multiple R4 assemblies please specify the centre/connection kit: PAR4-R4 required between each section. entre Kit Lengths: R4 to R4-34mm R5 to R4-34mm R6 to R4-52.4mm Specify lockwise/righthand or Anti-clockwise/Left-hand rotation, these pumps are not available as i-rotational units. Length of Shaft End over and Mounting Flange: 63.5mm Seal Kit Ordering ode For a single pump/front section (A Design) with single shaft seal without tell-tale: PAR4ASK For a single pump/front section ( Design) with two shaft seals and tell-tale for wet mount requirements: PAR4SK For a centre section/rear section: PAR4/RSK 75

50 click here to return to front page David rown / Hydreco QS4 - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAS4 016 A SA2 V (16.0cc/rev capacity, A shaft, SA2 flange, single pump, blank back cover, A Design (single viton seal and wiper)) PAS4 032 S2W W (30.9cc/rev cap., shaft, S2W wet mount flange, single pump, blank back cover, Design (2 viton shaft seals, wiper and tell-tale)) PAS4 037 H S4 A V (35.8cc/rev capacity, H shaft, S4 flange, front section, A Design (single viton seal and wiper)) PAS4 042 Q S2W A W (40.6cc/rev capacity, Q shaft, S2W wet mount flange, front section, Design (2 viton shaft seals, wiper and tell-tale)) PAS4 027 A (26.1cc/rev capacity, centre section) PAS4 032 E (30.9cc/rev capacity, rear section, blank end cover) Front Section/Single Pump PAS4 *** $$$???? &! Very Low Noise - Virtually Silent entre/rear Section PAS4 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 77???? Mounting Flange See codes in purple boxes under flange diagrams on page 77. Flange codes ending with 'W' are for wet mount applications - pumps with two viton shaft seals (Shaft Seal code W). & Model/Features A front section single pump - blank back cover (not portable)! Shaft Seal V W A Design: Single Viton Seal and wiper for external drives Design: Two viton shaft seals, inner and outer seal with tell-tale hole. The tell-tale hole indicates leakage before mixing of fluids can occur. *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model A centre section E rear section - blank end cover (not portable) Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Single ody Length mm Intermediate ody Length mm Dimension A (see page 77 for drawing) mm Dimension (see page 77 for drawing) mm Dimension (see page 77 for drawing) mm Ports entre/onnection Kit Rotation Length of Shaft End over Ports of your choice - see pages 77 and 86 for options. Please specify your port choice when ordering. For multiple S4 assemblies please specify the centre/connection kit: PAS4-S4 required between each section. entre Kit Lengths: S4 to S4-34mm S5 to S4-34mm S6 to S4-52.4mm Specify lockwise/righthand or Anti-clockwise/Left-hand rotation, these pumps are not available as i-rotational units. Length of Shaft End over and Mounting Flange: 63.5mm Seal Kit Ordering ode For a single pump/front section (A Design) with single shaft seal without tell-tale: PAS4ASK For a single pump/front section ( Design) with two shaft seals and tell-tale for wet mount requirements: PAS4SK For a centre section/rear section: PAS4/RSK 76

51 click here to return to front page David rown / Hydreco QR4 and QS4 - Single Pumps (standard ports), Mounting Flanges and Shafts QR4/QS4 Single Pumps - standard ports QR4/QS4 Shaft Type A Outlet Port Inlet Port Drawings show clockwise rotation pumps. For anti-clockwise rotation pumps reverse the inlet and outlet port positions. (Rotation convention - view from pump shaft end). Dimensions A, and - please see the specification table for the relevant pump: QR4 - page 75 QS4 - page deep thread 3.97 ø A 5/8 SAE A, 9 Tooth Spline Torque Rating Nm 7/8 SAE, 13 Tooth Spline Torque Rating Nm E 5/8 SAE A, Parallel Torque Rating Nm ø deep thread 6.3 F 7/8 SAE, Parallel Torque Rating Nm QR4/QS4 Mounting Flange Type ø10.97 ø deep thread ø ø H 1 SAE, Parallel Torque Rating Nm ø Q 1 SAE, 15 Tooth Spline Torque Rating Nm ø14.17 ø SA2/SA2W 2 olt SAE A S2/S2W 2 olt SAE S4/S4W 4 olt SAE ø ø17.37 S2/S2W 2 olt SAE 91.0 ø14.17 S4/S4W 4 olt SAE 77

52 click here to return to front page David rown / Hydreco QR5 - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAR5 045 S2 V (45 cc/rev capacity, shaft, S2 flange, single pump, blank back cover, A Design (single viton seal and wiper)) PAR5 073 S2W W (73 cc/rev cap., shaft, S2W wet mount flange, single pump, blank back cover, Design (2 viton shaft seals, wiper and tell-tale)) PAR5 100 H S4 A V (100 cc/rev capacity, H shaft, S4 flange, front section,, A Design (single viton seal and wiper)) PAR5 063 Q S2W A W (63 cc/rev capacity, Q shaft, S2W wet mount flange, front section, Design (2 viton shaft seals, wiper and tell-tale)) PAR5 085 A (85 cc/rev capacity, centre section) PAR5 120 E (120 cc/rev capacity, rear section, blank end cover) Front Section/Single Pump entre/rear Section PAR5 *** $$$???? &! PAR5 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 80???? Mounting Flange See codes in purple boxes under flange diagrams on page 80 Flange codes ending with 'W' are for wet mount applications - pumps with two viton shaft seals (Shaft Seal code W). & Model/Features A front section single pump - blank back cover (not portable)! Shaft Seal V W A Design: Single Viton Seal and wiper for external drives Design: Two viton shaft seals, inner and outer seal with tell-tale hole. The tell-tale hole indicates leakage before mixing of fluids can occur. *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev cc/rev && Model A centre section E rear section - blank end cover (not portable) Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Single ody Length mm Intermediate ody Length mm Dimension A (see page 80 for drawing) mm Dimension (see page 80 for drawing) mm Dimension (see page 80 for drawing) mm Ports entre/onnection Kit Rotation Length of Shaft End over Ports of your choice - see pages 80 and 86 for options. Please specify your port choice when ordering. For multiple R5 assemblies please specify the centre/connection kit: PAR5-R5 required between each section. entre Kit Lengths: R5 to R5-41.5mm R6 to R5-43mm R5 to R4-34mm Specify lockwise/righthand or Anti-clockwise/Left-hand rotation, these pumps are not available as i-rotational units. Length of Shaft End over and Mounting Flange: 74.5mm Seal Kit Ordering ode For a single pump/front section (A Design) with single shaft seal without tell-tale: PAR5ASK For a single pump/front section ( Design) with two shaft seals and tell-tale for wet mount requirements: PAR5SK For a centre section/rear section: PAR5/RSK 78

53 click here to return to front page David rown / Hydreco QS5 - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAS5 045 S2 V (45 cc/rev capacity, A shaft, S2 flange, single pump, blank back cover, A Design (single viton seal and wiper)) PAS5 085 S2W W (85 cc/rev cap., shaft, S2W wet mount flange, single pump, blank back cover, Design (2 viton shaft seals, wiper and tell-tale)) PAS5 085 H S4 A V (85 cc/rev capacity, H shaft, S4 flange, front section, A Design (single viton seal and wiper)) PAS5 085 Q S2W A W (85 cc/rev capacity, Q shaft, S2W wet mount flange, front section, Design (2 viton shaft seals, wiper and tell-tale)) PAS5 085 A (85 cc/rev capacity, centre section) PAS5 085 E (85 cc/rev capacity, rear section, blank end cover) Front Section/Single Pump Very Low Noise - Virtually Silent entre/rear Section PAS5 *** $$$???? &! PAS5 *** && *** apacity cc/rev cc/rev 0 58 cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 80???? Mounting Flange See codes in purple boxes under flange diagrams on page 80. Flange codes ending with 'W' are for wet mount applications - pumps with two viton shaft seals (Shaft Seal code W). & Model/Features A front section single pump - blank back cover (not portable)! Shaft Seal V W A Design: Single Viton Seal and wiper for external drives Design: Two viton shaft seals, inner and outer seal with tell-tale hole. The tell-tale hole indicates leakage before mixing of fluids can occur. *** apacity cc/rev cc/rev 0 58 cc/rev cc/rev cc/rev && Model A centre section E rear section - blank end cover (not portable) Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Single ody Length mm Intermediate ody Length mm Dimension A (see page 80 for drawing) mm Dimension (see page 80 for drawing) mm Dimension (see page 80 for drawing) mm Ports entre/onnection Kit Rotation Length of Shaft End over Ports of your choice - see pages 80 and 86 for options. Please specify your port choice when ordering. For multiple S5 assemblies please specify the centre/connection kit: PAS5-S5 required between each section. entre Kit Lengths: S5 to S5-41.5mm S6 to S5-43mm S5 to S4-34mm Specify lockwise/righthand or Anti-clockwise/Left-hand rotation, these pumps are not available as i-rotational units. Length of Shaft End over and Mounting Flange: 74.5mm Seal Kit Ordering ode For a single pump/front section (A Design) with single shaft seal without tell-tale: PAS5ASK For a single pump/front section ( Design) with two shaft seals and tell-tale for wet mount requirements: PAS5SK For a centre section/rear section: PAS5/RSK 79

54 click here to return to front page David rown / Hydreco QR5/QS5 - Single Pumps (standard ports), Mounting Flanges and Shafts QR5/QS5 Single Pumps - standard ports Outlet Port A Inlet Port Drawings show clockwise rotation pumps. For anti-clockwise rotation pumps reverse the inlet and outlet port positions. (Rotation convention - view from pump shaft end). Dimensions A, and - please see the specification table for the relevant pump: QR5 - page 78 QS5 - page 79 QR5/QS5 Shaft Type /8 SAE, 13 Tooth Spline Torque Rating Nm 1 1/4 SAE, 14 Tooth Spline Torque Rating Nm deep thread G 1 1/4 SAE, Parallel Torque Rating Nm QR5/QS5 Mounting Flange Type ø14.17 S2/S2W 2 olt SAE 8.9 ø deep thread ø14.17 S4/S4W 4 olt SAE 8.9 ø ø H 1 SAE, Parallel Torque Rating Nm Q 1 SAE, 15 Tooth Spline Torque Rating Nm S2/S2W 2 olt SAE ø17.37 ø ø14.17 S4/S4W 4 olt SAE

55 click here to return to front page David rown / Hydreco QR6 - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAR6 137 S2 V (137 cc/rev capacity, shaft, S2 flange, single pump, blank back cover, A Design (single viton seal and wiper)) PAR6 220 S2W W (220 cc/rev cap., shaft, S2W wet mount flange, single pump, blank back cover, Design (2 viton shaft seals, wiper and tell-tale)) PAR6 100 N S4 A V (100 cc/rev capacity, N shaft, S4 flange, front section, A Design (single viton seal and wiper)) PAR6 137 T S2W A W (137 cc/rev capacity, T shaft, S2W wet mount flange, front section, Design (2 viton shaft seals, wiper and tell-tale)) PAR6 117 A (117 cc/rev capacity, centre section) PAR6 220 E (220 cc/rev capacity, rear section, blank end cover) Front Section/Single Pump entre/rear Section PAR6 *** $$$???? &! PAR6 *** && *** apacity cc/rev cc/rev cc/rev 1 1 cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 83???? Mounting Flange See codes in purple boxes under flange diagrams on page 83. Flange codes ending with 'W' are for wet mount applications - pumps with two viton shaft seals (Shaft Seal code W). & Model/Features A front section single pump - blank back cover (not portable)! Shaft Seal V W A Design: Single Viton Seal and wiper for external drives Design: Two viton shaft seals, inner and outer seal with tell-tale hole. The tell-tale hole indicates leakage before mixing of fluids can occur. *** apacity cc/rev cc/rev cc/rev 1 1 cc/rev cc/rev cc/rev && Model A centre section E rear section - blank end cover (not portable) Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Single ody Length mm Intermediate ody Length mm Dimension A (see page 83 for drawing) mm Dimension (see page 83 for drawing) mm Dimension (see page 83 for drawing) mm Ports entre/onnection Kit Rotation Length of Shaft End over Ports of your choice - see pages 83 and 86 for options. Please specify your port choice when ordering. For multiple R6 assemblies please specify the centre/connection kit: PAR6-R6 required between each section. entre Kit Lengths: R6 to R6-54mm R6 to R5-43mm R6 to R4-52.4mm Specify lockwise/righthand or Anti-clockwise/Left-hand rotation, these pumps are not available as i-rotational units. Length of Shaft End over and Mounting Flange: 91mm Seal Kit Ordering ode For a single pump/front section (A Design) with single shaft seal without tell-tale: PAR6ASK For a single pump/front section ( Design) with two shaft seals and tell-tale for wet mount requirements: PAR6SK For a centre section/rear section: PAR6/RSK 81

56 click here to return to front page David rown / Hydreco QS6 - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAS6 132 S2 V (127.6 cc/rev capacity, shaft, S2 flange, single pump, blank back cover, A Design (single viton seal and wiper)) PAS6 155 S2W W (149.9 cc/rev cap., shaft, S2W wet mount flange, single pump, blank back cover, Design (2 viton shaft seals, wiper and tell-tale)) PAS6 113 N S4 A V (109.3 cc/rev capacity, N shaft, S4 flange, front section, A Design (single viton seal and wiper)) PAS6 083 T S2W A W (80.3 cc/rev capacity, T shaft, S2W wet mount flange, front section, Design (2 viton shaft seals, wiper and tell-tale)) PAS6 097 A (98.3 cc/rev capacity, centre section) PAS6 132 E (127.6 cc/rev capacity, rear section, blank end cover) Front Section/Single Pump PAS6 *** $$$???? &! Very Low Noise - Virtually Silent entre/rear Section PAS6 *** && *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 83???? Mounting Flange See codes in purple boxes under flange diagrams on page 83. Flange codes ending with 'W' are for wet mount applications - pumps with two viton shaft seals (Shaft Seal code W). & Model/Features A front section single pump - blank back cover (not portable)! Shaft Seal V W A Design: Single Viton Seal and wiper for external drives Design: Two viton shaft seals, inner and outer seal with tell-tale hole. The tell-tale hole indicates leakage before mixing of fluids can occur. *** apacity cc/rev cc/rev cc/rev cc/rev cc/rev && Model A centre section E rear section - blank end cover (not portable) Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Single ody Length mm Intermediate ody Length mm Dimension A (see page 83 for drawing) mm Dimension (see page 83 for drawing) mm Dimension (see page 83 for drawing) mm Ports entre/onnection Kit Rotation Length of Shaft End over Ports of your choice - see pages 83 and 86 for options. Please specify your port choice when ordering. For multiple S6 assemblies please specify the centre/connection kit: PAS6-S6 required between each section. entre Kit Lengths: S6 to S6-54mm S6 to S5-43mm S6 to S4-52.4mm Specify lockwise/righthand or Anti-clockwise/Left-hand rotation, these pumps are not available as i-rotational units. Length of Shaft End over and Mounting Flange: 91mm Seal Kit Ordering ode For a single pump/front section (A Design) with single shaft seal without tell-tale: PAS6ASK For a single pump/front section ( Design) with two shaft seals and tell-tale for wet mount requirements: PAS6SK For a centre section/rear section: PAS6/RSK 82

57 click here to return to front page David rown / Hydreco QR6/QS6 - Single Pumps (standard ports), Mounting Flanges and Shafts QR6/QS6 Single Pumps - standard ports Outlet Port A Inlet Port Drawings show clockwise rotation pumps. For anti-clockwise rotation pumps reverse the inlet and outlet port positions. (Rotation convention - view from pump shaft end). Dimensions A, and - please see the specification table for the relevant pump: QR6 - page 81 QS6 - page 82 QR6/QS6 Shaft Type /4 SAE 14 Tooth Spline Torque Rating Nm 19 deep thread 7.94 G 1 1/4 SAE Parallel Torque Rating Nm T 1 1/2 SAE 17 Tooth Spline Torque Rating Nm deep thread N 1 1/2 SAE Parallel Torque Rating Nm QR6/QS6 Mounting Flange Type ø17.37 ø ø S2/S2W 2 olt SAE S4/S4W 4 olt SAE 83

58 click here to return to front page David rown / Hydreco QS7 - Ordering ode, Seal Kits and Specifications Ordering ode (Single or Multiple Sections with ports of your choice) Use this chart to compile your ordering code. For example: PAS7 155 S4 N (149.9 cc/rev capacity, shaft, S4 flange, single pump, blank back cover, A Design (single viton seal and wiper)) PAS7 248 S4W E (239.8 cc/rev cap., shaft, S4W wet mount flange, single pump, blank back cover, Design (2 viton shaft seals, wiper and tell-tale)) PAS7 180 N S4 A N (174.1 cc/rev capacity, N shaft, S4 flange, front section, A Design (single viton seal and wiper)) PAS7 208 T SD4W A E (201.1 cc/rev capacity, T shaft, SD4W wet mount flange, front section, Design (2 viton shaft seals, wiper and tell-tale)) PAS7 208 A (201.1 cc/rev capacity, centre section) PAS7 248 E (239.8 cc/rev capacity, rear section, blank end cover) Front Section/Single Pump Very Low Noise - Virtually Silent entre/rear Section PAS7 *** $$$???? &! PAS7 *** && *** apacity cc/rev cc/rev cc/rev cc/rev $$$ Shaft see codes in purple boxes under shaft diagrams on page 85???? Mounting Flange See codes in purple boxes under flange diagrams on page 85. Flange codes ending with 'W' are for wet mount applications - pumps with two viton shaft seals (Shaft Seal code W). & Model/Features A front section single pump - blank back cover (not portable)! Shaft Seal V W A Design: Single Viton Seal and wiper for external drives Design: Two viton shaft seals, inner and outer seal with tell-tale hole. The tell-tale hole indicates leakage before mixing of fluids can occur. && Model/Features A centre section E *** apacity cc/rev cc/rev cc/rev cc/rev rear section - blank end cover (not portable) Specifications Pump Model Displacement cc/rev in3/rev Max ontinuous Pressure bar psi Max Intermittent Pressure bar psi Minimum speed at max outlet pressure rpm Maximum speed at 0 inlet and max outlet pressure rpm Pump input power at max pressure and 1500 rpm kw Single ody Length mm Intermediate ody Length mm Dimension A (see page 85 for drawing) mm Dimension (see page 85 for drawing) mm Dimension (see page 85 for drawing) mm Ports entre/onnection Kit Rotation Length of Shaft End over Ports of your choice - see pages 85 and 86 for options. Please specify your port choice when ordering. For multiple S7 assemblies please specify the centre/connection kit: PAS7-S7 required between each section. entre Kit Lengths: S7 to S7-93mm S7 to S6-84.2mm Specify lockwise/righthand or Anti-clockwise/Left-hand rotation, these pumps are not available as i-rotational units. Length of Shaft End over and Mounting Flange: 56mm Seal Kit Ordering ode For a single pump/front section (A Design) with single shaft seal without tell-tale: PAS7ASK For a single pump/front section ( Design) with two shaft seals and tell-tale for wet mount requirements: PAS7SK For a centre section/rear section: PAS7/RSK 84