STOL CH 701. STOL CH701 cabin. Top view: Tunnel 7F11-4 between the Seats. STOL CH701 Seats
|
|
- Valentine Ramsey
- 5 years ago
- Views:
Transcription
1 CH701 cabin Top view: Tunnel 7F11-4 between the Seats. CH701 Seats CHECK: If the Gusset 7F11-7 is supplied bent; hen it is best to install the Gusset before the Seat 7F16-1. Otherwise, install the Seat than the Gusset. SECTION 12 - Page 1 of 13
2 L Angle, detail of bottom aft corner Ref: 7-F-16 L Angle riveted to the side of the Tunnel. The bend of the L Angle is approximately 20mm up from the Floor Bend the 90degree flange of the L Angle 65 degrees closed. ORIENTATION: Bend is along the top A4 PITCH 40 Drill the L Angle to the side of the Tunnel 7F11-4 SECTION 12 - Page 2 of 13
3 LAYOUT Mark a reference line 20mm up from the bottom edge of the Seat Back 7F6-4 TIP: The L Angle along the bottom of the Seat Back will be back drilled after the Seats 7F16-1 have been positioned. Cutout to the make room for the vertical stiffeners on the Cabin Side. SUGGESTION: Make a half template of the seat (from construction paper or scrap material) Photo of the outboard template: Reference: the front is flush with the Seat Front. SECTION 12 - Page 3 of 13
4 Detail of front outboard corner 70mm measured long the top of the Cabin Side from the Seat Front to the edge of the Seat. Detail of rear outboard cutout: 75x32mm The bend the Seat is even with the bottom edge of the Seat Back. SECTION 12 - Page 4 of 13
5 Trial fit template to determine the inboard cutout on the Seat 7F16-1 Half template: a smaller seat template is like a cross section. Keep trimming back until the top makes contact with the side of the Tunnel 7F11-4 Detail of aft corner Leave a 3 to 5mm gap between the inboard edge of the Seat and the Tunnel SECTION 12 - Page 5 of 13
6 Tape the I/B and O/B template together. Use the template to trim the Seat 7F16-1 7F16-1 Seat ORIENTATION: The bent flange is towards the back Seat panel 7F16-1 SECTION 12 - Page 6 of 13
7 A4 PITCH 30 7F16-1 to 7F11-1 Drill & Cleco the front of the Seat to the top flange of the Seat Front Drill & Cleco the aft flange of the Seat to the Seat Back. Edge distance: the rivet line is 10mm up from the bottom edge of the Seat Back. A4 PITCH 30 7F16-1 to 7F6-4 SECTION 12 - Page 7 of 13
8 A4 PITCH 40 7F16-1 & L Angle Drill & Cleco the inboard edge of the Seat to the L Angle. Trace along the Seat to make the position on the Cabin Side. A4 PITCH 40 L Angle & Cabin Side Drill and cleco a short L Angle to side Cabin Side, the bend is along the top even with the traced line. SECTION 12 - Page 8 of 13
9 3 RIVETS A4 7F16-1 & Short L Let the Seat sit. Drill & Cleco the outboard side of the Seat to the short angle on the Cabin Side. Layout a piece of flat material over the opening, trace along the Seat and the Seat Front. Photo of right side. The Gusset 7F11-7 closes the opening between the Cabin Side, the Seat Front and the Seat. SECTION 12 - Page 9 of 13
10 Top view of left side Gusset, left side Gusset 7F11-7 Front flange The front flange overlaps behind the Seat Front 7F11-1 The side flange fits underneath the Cabin Side. SECTION 12 - Page 10 of 13
11 Gusset 7F11-7 Rear flange The aft flange rivets to the Seat Detail of right side: Gusset and short L Angle SECTION 12 - Page 11 of 13
12 TUNNEL GUSSET 7F16-1A 6 RIVETS A4 Tunnel Gusset to connect the top of the Tunnel to the Seat Back Overlap of the front left and right seats Rivet line through the top flange of the Seat Front. SECTION 12 - Page 12 of 13
13 Back drill the L Angle through the hole in the Seat Back (holes for the seat) L Angle: length = 1025mm Clamp the L Angle on the backside of the Seat back. Viewed from inside the fuselage looking forwards. L Angle along the bottom of the Seat Back. ORIENTATION: the bend is towards the bottom. The ends of the L Angle overlap on top of the Upright 7F11-5 SECTION 12 - Page 13 of 13
ZODIAC 601 XL. Trim the outboard corner of the front flange of the center spar 6W4-1. Corner should not touch the side of the cabin floor skin 6B10-1.
Trim the outboard corner of the front flange of the center spar 6W4-1. Corner should not touch the side of the cabin floor skin 6B10-1. Tape the side skins to the cabin floor skin (area in front of the
More informationFUSELAGE CABIN ASSEMBLY
SECTION 3 Cabin Frame Ref Dwg 8FC-3 The Top of the Cabin Frame is level The distance between the front and rear wing attachment to fit the wings SECTION 3 - Page 1 of 10 CABIN FRAME 8F18-1 The TOP TUBES
More informationSection 75-FA-4. Forward Fuselage
Section 75-FA-4 This manual has been prepared for assembly of the forward fuselage skins supplied with match drilled parts. This photo assembly manual is intended as a supplement to the drawings. If there
More informationSection 75-ZA-3 Fin & Rudder Cable Fairing Installation
Section 75-ZA-3 Fin & Rudder Cable Fairing Installation This manual has been prepared for installation of the Fin and Fairings. This photo assembly manual is intended as a supplement to the drawings. If
More informationSTOL CH F8-2 Front Floor Stiffener. Cut and position the Front Floor Stiffener to the Floor 7F8-7. Back drill through the Floor 7F8-7.
Wait to drill the ends of the Seat Front 7F11-1 to the L angle on the cabin side at location A-A Ref 7-F-9 until after the Cabin Frame is installed. Ref Fuselage Cabin Frame, Section 10, page 11. NOTE:
More information12/03 EXPLODED VIEW 1) L angles on first rear rib: moved from inboard to outboard side of rib (12/03)
ZODIAC CH 601 XL Drawing list December 04, 2003 3 rd revision of 2 nd edition 12/03 Summary of revisions from 07/03 to 11/03 AIRFRAME 6-X-0 DRAWING LIST Dec 4, 2003 6-X-1 6-T-0 6-T-1 6-T-2 6-T-3 6-T-4
More informationUPDATES to Revision 3, 9/99 Date this document was printed: 12/20/02
UPDATES to Revision 3, 9/99 Date this document was printed: 12/20/02 CAD drawings 80-DBT (01/01) update to (06/99) location of the hole for the fuel line through Flaperon Arm 8V4-7: the bottom edge of
More informationAIRCRAFT FINISHING Assembling the Front Seat Frames
AIRCRAFT FINISHING Assembling the Front Seat Frames Front Seat (shown with custom leather upholstery) The front seat frame assembly is supplied without upholstery. The seat back is hinged at the bottom
More informationPage: MEMO: In Figure 3, "2X 1 3/32 [27.78 mm]" was "2X 1 3/32 [2.75 mm]"
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationSECTION 22: FWD LOWER FUSELAGE VAN'S AIRCRAFT, INC F-1257 RUDDER PEDAL SUPPORT CHANNEL, 4 PLACES WD-1204 ENGINE MOUNT BRACKET, 2 PLACES
SECTION 22: F-1257 RUDDER PEDAL SUPPORT CHANNEL, WD-1204 ENGINE MOUNT BRACKET, VAN'S AIRCRAFT, INC. FWD LOWER F-1201B FIREWALL SHELF FIREWALL BOTTOM FUSELAGE TUNNEL RIB F-1271-R FWD FUSE CORNER SKIN F-1288
More informationROLL BAR FRAME 2 PLACES F-1231A-FL ROLL BAR FRAME F-1231C INBOARD F-1231B OUTBOARD ROLL BAR STRAP BAGGAGE BULKHEAD
SECTION 24iS/U: ROLLOVER F-1231A-FR ROLL BAR FRAME VAN'S AIRCRAFT, INC. F-1231A-AR ROLL BAR FRAME STRUCTURE F-1231E ROLL BAR SPLICE PLATE 2 PLACES F-1232A ROLL BAR BRACE F-01254-R-1 SUPPORT FRAME & F-01207
More information11 - Fairings. Fairings. February XLF Page 11-1
11 - Fairings Fairings February 2003 11-XLF Page 11-1 11 - Fairings This Page Intentionally Left Blank Page 11-2 11-XLF February 2003 11 - Fairings Contents 11.0 - Chapter Preface... 11-4 11.0.1 - Parts
More information2000 SERIES SPEEDBRAKE INSTALLATION MANUAL MOONEY M20 SERIES & M22 STC NO. SA4342NM NOTE: READ THESE DIRECTIONS BEFORE STARTING!
INSTALLATION REPORT NO. 08059 Serial Number PRECISE FLIGHT, INC. 800-547-2558 2000 SERIES SPEEDBRAKE INSTALLATION MANUAL MOONEY M20 SERIES & M22 NOTE: READ THESE DIRECTIONS BEFORE STARTING! THIS DOCUMENT
More informationPage REV 1: Added "Step 4: Bend the tabs on the wiring channel to match the slant of the F L & -R Tunnel Sides."
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More information2000 SERIES SPEEDBRAKE INSTALLATION MANUAL PA28/PA32 STC # SA00762SE
INSTALLATION REPORT NO. 08067 Serial Number PRECISE FLIGHT, INC. 800-547-2558 2000 SERIES SPEEDBRAKE INSTALLATION MANUAL PA28/PA32 STC # SA00762SE NOTE: READ THESE DIRECTIONS BEFORE STARTING! CHECK FOR
More informationPage: REV 1: In Step 4 "a minimum of 1/16 [1.6 mm] gap" was "an approximately 1/16 [1.6 mm] gap."
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationREVISION DESCRIPTION:
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationPage REV 1: In Step 1, added reference to fluid fitting clocking. Added Figure 2 and Figure 3.
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm DOCUMENTATION
More informationREVISION DESCRIPTION:
REVISION DESCRIPTION: 1) Page: 12-03 REV 1: Step 1: and Figure 1: Final-Drill s.b. Match-Drill. Step 4: Updated flox mixture description to match later description (removed "peanut butter-like" description).
More informationF-1202D-L PANEL ATTACH STRIP F L UPPER FWD FUSELAGE SKIN RIB F CABIN EGRESS HANDLE F-1240B COVER PLATE
SECTION 29iS/U: F-1202D-L PANEL ATTACH STRIP F-01240-1 UPPER FORWARD FUSELAGE SKIN (SHOWN TRANSPARENT) VAN'S AIRCRAFT, INC. FWD UPPER FUSELAGE F-00078 CABIN EGRESS HANDLE F-00077-L UPPER FWD FUSELAGE SKIN
More information1) Page: REV 5: Changed depiction to show added hardware and T-01220
REVISION DESCRIPTION: 1) Page: 37-01 REV 5: Changed depiction to show added hardware and T-01220 Page: 37-02 REV 4: Added Figure 3 depicting Separating the T-01220 Doublers. Figure 4 was Figure 3. Added
More informationREVISION LIST CHAPTER 14: CENTER CONSOLE
REVISION LIST CHAPTER 14: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationThe engine cowling installation and firewall should be inspected and modified as specified in this Service Bulletin.
Single Engine Service Bulletin August 25, 2008 TITLE ENGINE COWLING ALIGNMENT INSPECTION AND MODIFICATION EFFECTIVITY Model Serial Numbers 172R 17280001 thru 17280724 172S 172S8001 thru 172S8201 REASON
More informationperformance S T O L Installation Instructions Manual No. PSTOL-013 Double Slotted Flaps for Piper PA-18 Series Aircraft
performance S T O L Installation Instructions Manual No. PSTOL-013 Double Slotted Flaps for Piper PA-18 Series Aircraft 1 This Page Intentionally Left Blank 2 Record of Revisions Rev Level Date Page By
More information2000 SERIES SPEEDBRAKE INSTALLATION MANUAL STC NO. SA2602NM
INSTALLATION REPORT NO. 08062 Serial Number PRECISE FLIGHT, INC. 800-547-2558 2000 SERIES SPEEDBRAKE INSTALLATION MANUAL CESSNA 210G, T210G, 210H, 210J, 210K, T210J, 210L, T210L, 210M, T210M, 210N, P210N,
More informationDetroit Speed, Inc. Rear QUADRAlink Conversion Kit Camaro/Firebird P/N:
Detroit Speed, Inc. Rear QUADRAlink Conversion Kit 1982-92 Camaro/Firebird P/N: 041721 The Detroit Speed Inc. QUADRAlink Conversion Kit, eliminates the factory torque arm configuration. It features no-compromise
More information36-01 REV 1: Updated figure to depict current F Bellcrank configuration.
REVISION DESCRIPTION: 36-01 REV 1: Updated figure to depict current F-00067 Bellcrank configuration. 36-06 REV 1: Updated Figure 1 and Figure 2 to depict current F-00067 Bellcrank configuration. 36-07
More informationFAA approval has been obtained on technical data in this publication that affects airplane type design.
Single Engine Service Bulletin January 28, 2008 TITLE ENGINE COWLING ALIGNMENT INSPECTION AND MODIFICATION EFFECTIVITY Model Serial Numbers 172R 17280725 thru 17281262 172S 172S8202 thru 172S10006 REASON
More information2000 SERIES PA-30 / PA-39 STC NO. SA00233SE PA-24 STC NO. SA4150NM
INSTALLATION REPORT NO. 08073 Serial Number PRECISE FLIGHT, INC. 800-547-2558 2000 SERIES SPEEDBRAKE INSTALLATION MANUAL PA-30 / PA-39 STC NO. SA00233SE PA-24 STC NO. SA4150NM NOTE: READ THESE DIRECTIONS
More information12.0 CONTROLS 3/3/2006. Page 1
Page 1 Page 2 SR3500 Rudder Pedal Parts List ITEM DESCRIPTION PART NUMBER QTY 1 MASTER BRAKE PEDAL RP0015 2 2 SLAVE BRAKE PEDAL RP0016 2 3 PUSH ROD RP0017 4 4 SLAVE BRAKE TORQUE TUBE RP0018 2 5 MASTER
More information71685 Landing Light Kit Installation Instructions
71685 Landing Light Kit Installation Instructions Overview The 71685 Whelen landing light kit is designed to install into the wingtip lens area of an RV. Its important to note that the tip installation
More informationPage: MEMO: In NOTE before Step 5, "Whenever possible, ream using a drill press..." was "Always ream using a drill press...".
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationInstallation Instructions
Installation Instructions Manual No. PSTOL-013 Performance STOL Double Slotted Flaps for Piper PA-18 Series Aircraft 1 This Page Intentionally Left Blank 2 Record of Revisions Rev Level Date Page By Explanation
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1J update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...
More information4-Bulkheads. Bulkheads. December XLR Page 4-1
Bulkheads December 2007 04-XLR Page 4-1 This Page Intentionally Left Blank Page 4-2 04-XLR December 2007 Contents 4.0 - Chapter Preface...4-4 4.0.1 - Parts List... 4-4 4.0.2 - Tools List... 4-4 4.0.3 -
More informationFUSELAGE ASSEMBLY SECOND SECTION (of three)
FUSELAGE ASSEMBLY SECOND SECTION (of three) 1 FRONT FLOOR ASSEMBLY The front floor assembly is fabricated from three pieces of the two ply pre-pregnated panel material supplied. The basic floor panel and
More informationSection C75-CA-2. Elevator Controls
Section C75-CA-2 This manual has been prepared for assembly of the. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy between this manual and the drawings,
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationREVISION DESCRIPTION: REV 2: Steps re-written for clarity REV 2: Steps re-written for clarity.
REVISION DESCRIPTION: 14-04 REV 2: Steps re-written for clarity. 14-05 REV 2: Steps re-written for clarity. SECTION 14: W-1012-L OUTBOARD W-1012-R TRIMMED OUTBOARD S W-1012-L OUTBOARD W-1025B-R FLAP HINGE
More informationPage: REV 3: Add drill and tap information to Figure 4 DRILL #3, TAP 1/4-28 BOTH ENDS.
REVISION DESCRIPTION: 1) Page: 32-03 MEMO: Step 4 should not be bold. Fix WD-1213 callout in Figure 3. Page: 32-04 REV 3: Add drill and tap information to Figure 4 DRILL #3, TAP 1/4-28 BOTH ENDS. Add make
More informationSERVICE KIT thru , 631, 634, 675 R thru R F thru F FR thru FR
TITLE SEAT BELT AND SHOULDER HARNESS KIT INSTALLATION EFFECTIVITY MODEL SERIES SERIAL NUMBERS 182 33000 thru 18268368 182 613, 631, 634, 675 R182 R18200001 thru R18201973 F182 F18200001 thru F18200169
More informationFLAP, AILERON, FLAP/FUSELAGE AND STABILATOR GAP SEAL INSTALLATION AND MAINTENANCE MANUAL
FLAP, AILERON, FLAP/FUSELAGE AND STABILATOR GAP SEAL INSTALLATION AND MAINTENANCE MANUAL Aircraft Eligibility: Piper PA-28-151, PA-28-161, PA-28-181, PA-28-201T, PA-28-236, PA- 28R-201, PA-28R-201T, PA-28RT-201,
More informationTrident Universal. Installation Manual
Trident Universal Installation Manual Revision 1.1; Updated: July 6, 2017 Table of Contents Tool List 03 Installation Tool List Pre-Install Preparation 04 Lateral Panel Modifications 07 Top Panel Modifications
More informationSECTION 26iS/U: FUEL TANK VAN'S AIRCRAFT, INC. T R OUTBOARD RIB IE-00001X MECHANICAL FUEL GAUGE T R INBOARD RIB T R
VAN'S AIRCRAFT, INC. SECTION 26iS/U: IE-00001X MECHANICAL FUEL GAUGE T-01222-R OUTBOARD RIB FUEL TANK T-01223-R INBOARD RIB T-01228 RETURN LINE BRACKET T-01224-R INBOARD RIB T-01229 INLET ASSEMBLY T-01223-L
More informationNEW PRODUCT RELEASE. PRODUCT/KIT NAME: 12 Stabilator Tip Fairing Kit
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm NEW PRODUCT
More informationSERVICE BULLETIN
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm SERVICE
More informationFIREWALL FORWARD GENERAL
GENERAL The configuration of the aircraft forward of the firewall will vary from aircraft to aircraft depending on engine selection and other variables. The effort here must be well thought-out and neatly
More informationPlace these instructions in vehicle s glove box after installation is complete. Clean Tonneau Cover with a mild detergent and water solution.
Place these instructions in vehicle s glove box after installation is complete Installation Time: Approx. 60 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do
More informationAFT MOUNTED OXYGEN SYSTEM INSTALLATION BEECHCRAFT 33, 35, 36, 55, AND 58
ENGINE TECHNOLOGIES INC. REPORT 35-4960004, REV. A, JULY 12, 2013 INSTALLATION INSTRUCTIONS FOR OXYGEN SYSTEM ON HAWKER BEECHCRAFT S35, V35, V35A, V35B, 35-C33A, E33A, 36, A36, F33A, G33, 95-55, 95-A55,
More information10. Lower Fuselage Assembly Undercarriage
10. Lower Fuselage Assembly Undercarriage Undercarriage 10.27 2 230399 0 Jabiru Undercarriage Configurations There are four combinations of tyres available, utilising two sets of hubs (standard and heavy
More informationSECTION 47: COWL BAFFLE VAN'S AIRCRAFT, INC. CB RIGHT AFT BAFFLE CB CYLINDER 3 BAFFLE VA-187 4" FLANGED DUCT
SECTION 47: CB-00014 CYLINDER 3 BAFFLE CB-00015 RIGHT AFT BAFFLE VA-187 4" FLANGED DUCT COWL BAFFLE CB-00031-R MAGNETO COOLING TUBE CB-00016 AFT CENTER BRACKET CB-00017 LEFT AFT BAFFLE CB-00013 RIGHT AIR
More informationD'Shannon Aviation PANEL INSTALLATION INSTRUCTIONS
D'Shannon Aviation PANEL INSTALLATION INSTRUCTIONS Disconnect the battery posts 1. Windshield Removal NOTE: If the aircraft is equipped with a D'Shannon speed sloped windshield, you will not have to do
More informationDetroit Speed, Inc. Mustang Mini-Tub Kit Mustang P/N:
Detroit Speed, Inc. Mustang Mini-Tub Kit 1964.5-70 Mustang P/N: 040405 The Detroit Speed Mini-Tubs are inner wheel housings designed to accommodate wider wheel and tire package for the 1964½ - 1970 Mustang.
More informationDetroit Speed, Inc. Second Generation Camaro/Firebird Mini-Tub Kit Camaro/Firebird P/N: ,
Detroit Speed, Inc. Second Generation Camaro/Firebird Mini-Tub Kit 1970-1981 Camaro/Firebird P/N: 041222, 041223 The Detroit Speed Second Generation Camaro/Firebird Rear Mini-Tub Kit is designed to accommodate
More informationChevrolet 3100 IFS Kit
1947-54 Chevrolet 3100 IFS Kit Congratulations on your purchase on what we believe is the finest IFS kit available for 1947-54 Chevrolet pickups with stock frames. We have invested many hours into designing
More informationINSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools:
INSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools: Drill Bits: 9/16 (.5625 ) Power Drill Socket Wrench Set Square #2 Driver Rubber Mallet Utility Knife
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More informationSuper Dragon Glow Conversion
Super Dragon Glow Conversion Kit Contents: Kit # AG-501 Wood Bag: Qty......Name.......................................Description 1.......LC-G501-01.................................3mm X 6 X 24 Laser Cut
More information57-50 FLIGHT SURFACES
FLIGHT SURFACES 1. DESCRIPTION The flaps are mounted to the trailing edge of each wing between the inboard end of the ailerons and the fuselage. The ailerons are located near the wing tips and hinge to
More informationConvertible MM Roll Bar (MMRB-10.1 to -10.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1983-93 Convertible MM Roll Bar (MMRB-10.1 to -10.7) The Maximum Motorsports RB-10.1
More informationCHAPTER 15 FURNISHINGS. Section Title Page
CHAPTER 15 FURNISHINGS Section Title Page 15.000 Description..................................... 15.1 15.100 Seat Harnesses................................... 15.3 15.110 Four-Point Harness Assembly.................
More informationSection 75-CA-2. Elevator Controls
Section 75-CA-2 This manual has been prepared for assembly of the. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy between this manual and the drawings,
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationVAN'S AIRCRAFT, INC. SECTION 40: LIGHTING
SECTION 40: LIGHTING RIGHT WING ASSEMBLY W-00014 LENS LN-200-1 WING TIP NAV/POSITION/ STROBE LIGHT LL-200 LANDING LIGHT W-1223E LENS BACKING STRIP, W-1222-R EXTENSION W-1223B-L LANDING LIGHT RIB NOTE:
More informationC-10 Rear 4Link
Part # 11367199-1973-1987 C10 Rear 4Link Recommended Tools 1973-1987 C-10 Rear 4Link Installation Table of contents Page 2... Included Components Page 3... Hardware List & Getting Started Page 4... Disassembly
More informationDetroit Speed, Inc. Subframe Connector Kit Mustang P/N #
Detroit Speed, Inc. Subframe Connector Kit 1964.5-1968 Mustang P/N # 010105 Item Component Quantity 1 Subframe Connector 2 2 Front Frame Rail Doubler LH 1 3 Front Frame Rail Doubler RH 1 4 Front Frame
More informationPPM-5224-A JK 4 DOOR REAR CAGE KIT Version 1.1
PPM-5224-A JK 4 DOOR REAR CAGE KIT Version 1.1 GENERAL NOTES: These instructions are also available on our website; www.polyperformance.com. Check the website before you begin for any updated instructions
More informationDetroit Speed, Inc. Rear QUADRAlink Suspension Kit with 3 Axle Tube Camaro/Firebird P/N:
Detroit Speed, Inc. Rear QUADRAlink Suspension Kit with 3 Axle Tube 1982-92 Camaro/Firebird P/N: 041722 The Detroit Speed Inc. QUADRAlink Kit, eliminates the factory torque arm configuration. It features
More informationNIS NAV AM (MY15 >) - Aluminium Tonneau Cover ATC0051 (silver) ATC0052 (Black) Installation Time: Approx. 60 Minutes WARNING!
Installation Time: Approx. 60 Minutes WARNING! When in the closed position, Aluminium Tonneau Cover must be latched and tailgate must be closed. Failure to do so could result in unexpected opening of the
More informationFeb/March-2018 FEB/MARCH. Texas Flying Legends P-47 Update. by Chuck Cravens. The CAD rendering becomes reality in these two images.
FEB/MARCH Texas Flying Legends P-47 Update by Chuck Cravens The CAD rendering becomes reality in these two images. Update Remarkable progress has been made on the forward fuselage structure this month.
More informationREVISION LIST CHAPTER 21: FLAP SYSTEM COMPLETION
REVISION LIST CHAPTER 21: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationSection 13. Tail Rotor Drive. RotorWay International A600 TALON Construction Manual. Section 13. Page A
RotorWay International Page A Tail Rotor Drive Procedures covered in this section: Install driveshafts and gearboxes; install drive belt and tensioner; fabricate and install tail rotor pitch actuator arms;
More informationGlaStar and Sportsman Service Bulletin 67
GlaStar and Subject: Applicability: Issue: Compliance Time: Elevator counterweights All GlaStar and Aircraft Counterweight attachment to elevator end rib At or before next condition inspection Discussion
More information53-40 ATTACH FITTINGS
ATTACH FITTINGS. DESCRIPTION Attach fittings are provided for attachment of the seats (Refer to -0), baggage straps (Refer to -0), rear seat harnesses (Refer to -0), cargo net straps (Refer to -0), cabin
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
FLIGHT SURFACES. DESCRIPTION The flaps are mounted to the trailing edge of each wing between the inboard end of the ailerons and the fuselage. The ailerons are located near the wing tips and hinge to the
More informationPage REV 1: Added 'Step 2: See the "REMOVE THIS TAB, BOTH SIDES" callout near Detail A. Modify four SB375-4 Snap Bushings as shown.
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationSTEP 1 - APPLYING HINGE BEVELS TO FRONT WING, REAR WING, VERTICAL STABILIZER, AND RUDDER FRONT WING (UNDERSIDE) 45 DOUBLE HINGE BEVEL
SkyRaiderv.b WING SPAN: FRONT - 22 in. REAR - 28.5 in. LENGTH: 35.25" WING AREA: 381 sqin. WEIGHT: 19-20oz. (RECOMMENDED) POWER: HACKER A20-20L, 10x3.8 APC PROP, 3S1P 1320mah Lipo 15C, 20A ESC RADIO: 4
More information10.0 GRP Dash panel and fascia Fuse box and Relay block
10.0 GRP Dash panel and fascia 10.1 Fuse box and Relay block Decide the fixing point for the fuse boxes and relay blocks, check that the under dash section of the wiring loom can reach all the instruments,
More informationDetroit Speed, Inc. Subframe Connector Kit Mustang P/N #
Detroit Speed, Inc. Subframe Connector Kit 1969-1970 Mustang P/N # 010108 Item Component Quantity 1 Subframe Connector 2 2 Front Frame Rail Doubler LH 1 3 Front Frame Rail Doubler RH 1 4 Front Frame Rail
More informationFORD SuperRail Mounting Kit #3361
FORD SuperRail Mounting Kit #3361 #4100 SuperGlide (16K) #4400 SuperGlide (20K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationDetroit Speed, Inc Mustang Mini-Tubs P/N:
Detroit Speed, Inc. 1964.5-1970 Mustang Mini-Tubs P/N: 040405 Item Component Quantity 1 DSE Mini-Tubs - Mustang 2 2 Frame Rail Sections 2 3 Doubler Plate 4" x 3.25" 4 4 Doubler Plate 4" x 2" 4 5 Installation
More informationL/6.7L DODGE CUMMINS
6/15/2016 #1050310D 2005-09 5.9/6.7 Dodge Cummins FlowMAX Lift Pump Kit (I-00170) - 1-2005-09 5.9L/6.7L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT Installation Instructions P/N # 1050310D PLEASE READ ALL INSTRUCTIONS
More informationMustang Classic LightBar Instructions
1994-2004 Mustang Classic LightBar Instructions Note: Read installation instructions before starting. Component List: 1 LightBar 4 Poly Plugs 4 LightBar Bolts 4 LightBar Washers 2 LightBar Rivets 2 Light
More informationAPPLICABLE MODELS PA , PA , PA , PA , PA PA-28R-180, PA-28R-200, PA-28S-160, PA-28S-180
APPLICABLE MODELS PA-28-14, PA-28-15, PA-28-16, PA-28-18, PA-28-235 PA-28R-18, PA-28R-2, PA-28S-16, PA-28S-18 F L A P, A I L E R O N, F L A P / F U S E L A G E A N D S T A B I L A T O R G A P S E A L S.
More informationKI (14V) & KI (28V) R44
KI-228-1 (14V) & KI-228-2 (28V) R44 Radar Altimeter Installation Kit Instructions For B050 upper console only; includes parts for In-Console and Above-Console installations. NOTE Visit www.robinsonheli.com
More informationREVISION DESCRIPTION:
REVISION DESCRIPTION: 14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm
More informationRoll Bar (MMRB-1.1 to 1.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1979-93 Roll Bar (MMRB-1.1 to 1.7) The Maximum Motorsports RB-1.1 to -1.7 Roll
More informationChar-Griller Smokin Pro Modifications
Char-Griller Smokin Pro Modifications By Phil Lee aka HawgHeaven Right out of the box, the Char-Griller Smokin Pro has a few design deficiencies that need to be addressed, and are fairly easy to remedy.
More informationAirworthiness Directive Schedule
Airworthiness Directive Schedule Aeroplanes Cessna 120 26 November 2015 Notes 1. This AD schedule is applicable to Cessna 120 aircraft manufactured under Federal Aviation Administration (FAA) Type Certificate
More informationPlease reference the attached document for information regarding the installation of Utility Side Skirts (USS-160) on Dry Freight Trailers.
SERVICE BULLETIN NO. SB-19-004 Issue date: March 9, 2011 SUBJECT: Installing Dry Freight Side Skirts Please reference the attached document for information regarding the installation of Utility Side Skirts
More informationPart Numbers: TTU-BGP14 & TTU-BGB14
Date: 10.14.2015 TOYOTA TUNDRA 2014-17 Billet Grille Part Numbers: TTU-BGP14 & TTU-BGB14 Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 2 Flange Brackets
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter
More informationREVISION LIST CHAPTER 22: CABIN VENTILATION
REVISION LIST CHAPTER 22: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationInstallation Items: Cruise Module
Installation Items: Rostra 250-1223, Electronic Cruise Control System (ECCS) includes the cruise module, harness, cruise cable, cruise module mounting bracket, cruise cable mounting bracket and hardware
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationR44-series Ground Handling Wheel (Pop-Out Floats) Installation Kit Instructions ( upgrade to lever-style ground handling wheel assembly) NOTE
R44-series Ground Handling Wheel (Pop-Out Floats) Installation Kit Instructions ( upgrade to lever-style ground handling wheel assembly) NOTE Visit www.robinsonheli.com to verify kit instructions are current
More informationNC Kit # CE-182PQR-00 Air-conditioning installation manual and ICA for Cessna 182 P, Cessna 182 Q and Cessna 182 R
NC-04-041 Kit # CE-182PQR-00 Air-conditioning installation manual and ICA for Cessna 182 P, Cessna 182 Q and Cessna 182 R REVISION: E Date: November 10, 2004 Name Signature Date Author Len Elder 10/25/2004
More informationTORNADO II, S, & SS FUSELAGE TRACKING
TORNADO II, S, & SS FUSELAGE TRACKING 92-INS-0176-C Nose Fork Assembly Instructions Approved 92-INS-0178-D Spindle and Brake Assembly Approved 92-INS-0181-F Anti Servo Control Assembly Approved 92-INS-0182-C
More informationInstallation Instructions
UNIVERSAL 20K Industry Standard Rail Universal Mounting Kit #2720 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationTusk Pannier Racks. Instructions and information KLR
1 Tusk Pannier Racks Instructions and information KLR650 2008 + Congratulations on your purchase of the Tusk Pannier Racks. These racks are made to handle extreme adventure riding, but work great for the
More information