RIGGING GUIDE. Worldwide Edition

Transcription

1 2014 RIGGING GUIDE Worldwide Edition

2

3 PREFACE The information in this guide is based on 2014 model specification information available at the time when the guide has been issued. Throughout this guide, Worldwide model names are given first followed by US and Canada model names in parentheses for descriptive purpose. For Australia and New Zealand, US and Canada model names are used for 4-stroke 150HP and larger models. In this guide, particularly important information is distinguished in the following ways. WARNING A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. NOTICE A NOTICE indicates special precautions that must be taken to avoid damage to the products or other property. Specifications and descriptions are subject to change without notice. The PDF file is available from the service portal site maintained by Yamaha Motor Co., Ltd. The following contracted terms are expediently used in this guide. ASSY: assembly DEC: Digital Electronic Remote Control ECM: Electronic Control Module EXT: extension GND: ground, ( ) IG: ignition LED: light emitting diode MGT: management NA: not applicable, not available OP: optional P/N: part number PTT: power trim & tilt PWR: power RC: remote control STD: standard STR: steering SW: switch TD: to be determined Yamaha Motor Co., Ltd. All rights reserved. Mar Produced by Technical Publication Division After Sales Section CS Center

4

5 CONTENTS INSTALLATION TOP COVER PICTOGRAPH DESCRIPTION ENGINE OIL REMINDER TAG (4-STROKE ENGINES) UNCRATING PROCEDURE (FOR TYPICAL STEEL FRAME) MOUNTING THE OUTOARD MOTOR MOUNTING THE REMOTE OIL TANK OUTOARD MOTOR DIMENSIONS PROPELLERS PROPELLER SPECIFICATIONS PROPELLER SELECTION PROPELLER APPLICATIONS WOT OPERATION RANGE TALE REMOTE CONTROLS REMOTE CONTROL TYPES AND APPLICATIONS REMOTE SWITCH TYPES AND APPLICATIONS REMOTE CONTROL CALES REMOTE CONTROL ATTACHMENT KIT STEERING HOOK STEERING GUIDE ATTACHMENT KIT TIE-AR KIT CONVENTIONAL WIRE HARNESS DIGITAL ELECTRONIC REMOTE CONTROL WIRE HARNESS TILLER HANDLES X4 MULTI-FUNCTION TILLER HANDLE STEERING FRICTION CONTENTS To be continued.

6 CONTENTS CONVENTIONAL GAUGE (6Y5 & 6Y7) MOUNTING THE METERS ANALOG TACHOMETER DIGITAL TACHOMETER SPEEDOMETER FUEL MANAGEMENT GAUGE ANALOG TRIM METER COOLANT PRESSURE METER COOLANT TEMP. METER HOUR METER VOLTAGE METER FUEL METER CHARGE WARNING UNIT WIRE HARNESSES WIRING DIAGRAMS RIGGING GROMMET DESCRIPTION DIGITAL NETWORK GAUGE (6Y8) DIGITAL NETWORK GAUGE COMPATILE MODELS DIGITAL NETWORK GAUGE APPLICATION DIGITAL NETWORK GAUGE DIMENSIONS OPTIONAL EQUIPMENT WIRE HARNESS NETWORK HU OPTIONAL EQUIPMENT IMMOILIZER UNIT NETWORK WIRING DIAGRAMS INITIAL GAUGE SETUP TROULESHOOTING ASIC REQUIREMENTS NMEA0183 COMPATILE EQUIPMENT CONNECTION DIGITAL NETWORK GAUGE (6Y8) FUNCTION TALE DIGITAL NETWORK PREMIUM GAUGE (6Y9) DIGITAL NETWORK PREMIUM GAUGE COMPATILE MODELS DIGITAL NETWORK PREMIUM GAUGE APPLICATION DIGITAL NETWORK PREMIUM GAUGE DIMENSIONS OPTIONAL EQUIPMENT NETWORK HU WIRE HARNESS NETWORK WIRING DIAGRAMS To be continued.

7 CONTENTS ATTERY RECOMMENDED ATTERY ATTERY CALE LENGTH ATTERY WIRING APPENDIX MODEL NAME DESIGNATION FUEL SYSTEM VACUUM PRESSURE STANDARD PORTALE FUEL TANKS (TYPICAL) FUEL PIPES (TYPICAL) PRIMARY PUMP (TYPICAL) PRE-DELIVERY INSPECTION (PDI) CONVENTIONAL RIGGING KIT CONTENTS DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS IMMOILIZER RIGGING KIT CONTENTS DIGITAL NETWORK PREMIUM GAUGE RIGGING KIT CONTENTS OTHER RIGGING KIT CONTENTS YEAR MODELS MANUFACTURE STARTING SERIAL NUMERS

8

9 INSTALLATION TOP COVER PICTOGRAPH DESCRIPTION ENGINE OIL REMINDER TAG (4-STROKE ENGINES) UNCRATING PROCEDURE (FOR TYPICAL STEEL FRAME) MOUNTING THE OUTOARD MOTOR WATER LEVEL GUIDELINE (4-STROKE ENGINES) ADJUSTING TWIN ENGINES MAX. OAT SPEED ESTIMATION MOUNTING THE REMOTE OIL TANK REMOTE OIL TANK DIMENSIONS NOTICE FOR MOUNTING THE REMOTE OIL TANK OUTOARD MOTOR DIMENSIONS OVERALL DIMENSION ITEMS OVERALL DIMENSIONS (4-STROKE) OVERALL DIMENSIONS (2-STROKE) CLAMP RACKET DIMENSION ITEMS CLAMP RACKET DIMENSIONS

10 TOP COVER PICTOGRAPH DESCRIPTION The following pictographs are important sign to handle the crate. Read the NOTICE and understand what pictographs mean to avoid a damage to the product when handling, transporting and/or keeping the crate. * Photo shows F350. Lifting fork insert position Stack limit: Max. 4 units for storage Upward indication Care handling indication Water avoidance indication Product barycentric position ENGINE OIL REMINDER TAG (4-STROKE ENGINES) This tag is hung around the bottom cowling or the bracket to indicate that there is no engine oil in the oil pan when the outboard motor is uncrated. 1-2

11 UNCRATING PROCEDURE (FOR TYPICAL STEEL FRAME) 4. Remove the bottom bolts (3). WARNING Wear gloves to avoid injury by sharp steel edges while uncrating. This is an example of the steel crate for V6 models. For other steel crate models, refer to this procedure for uncrating the steel frame. 1. Inspect the crate for shipping damage. If any damage has been found, consult your Yamaha dealer. 2. Cut the strap (1). (1) 5. Lift the top frame (4) straight up. (3) (4) 3. Lift the top cover (2) straight up to remove. (2) 6. Remove the wrapping (5), and inspect the outboard motor for concealed damage. If any damage is found, consult your Yamaha dealer. (5) To be continued. 1-3

12 UNCRATING PROCEDURE (FOR TYPICAL STEEL FRAME) 7. Remove the top cowling (6). For 4-stroke V8, V6 (4.2L) and L4 (2.8L, 1.8L) engines, install the lifting attachment (A) to the flywheel using the exclusive 3 bolts (), insert the eye bolt (C) to the attachment, attach a lifting harness (D) to the eye bolt, and tension the harness. M10 bolt () torque: 36 Nm, 3.6 kgf m, 27 ft lb (A) (6) 8. If the lifting points are covered by the flywheel cover, remove it. 9. Attach a lifting harness (7) securely to the lifting points (8), and tighten the harness. (D) () (C) (7) (8) * Special service tool for 4-stroke V8, V6 (4.2L) and L4 (2.8L) engines: Lifting eye kit (P/N: ) Lifting eye kit contents: Eye bolt (C) Attachment (A) M10 bolt () (3 pcs) To be continued. 1-4

13 UNCRATING PROCEDURE (FOR TYPICAL STEEL FRAME) 10. Carefully lift up the motor with the bottom crate so that the lifting-harness does not contact the engine components. Have a helper hold the frame to avoid injury while lifting. 11. Remove the skeg holder (9) if it is attached. (9) MOUNTING THE OUTOARD MOTOR WARNING Overpowering a boat may cause severe instability. Never install an outboard motor that exceeds the maximum boat horsepower rating capacity. If a boat does not have the capacity plate, ask to the boat manufacturer. Proper mount of outboard motor will obtain better engine performance, product reliability, fuel economy, customer satisfaction, etc. This chapter describes the brief summary of outboard motor mount. For the first requirement, make sure the outboard motor has clearance for full movement, from port to starboard, as well as during tilt operation. For the motor dimensions, see the later pages. 1. Set an outboard motor on the vertical center line of boat transom. Measurement points are shown in the illustration. 12. Remove the bracket bolts (10). No strakes hull Make a same radius (R) at both sides of hull, and have another measurement points. C/L R (a) (b) R (c) (d) Strakes hull Make measurements between port and starboard strakes. C/L (10) (a) (c) (b) (d) *C/L: Centerline of the transom. To be continued. 1-5

14 MOUNTING THE OUTOARD MOTOR Recheck the measurements, and verify the boat transom vertical centerline is straight. Measurements (a) and (b) should be the same, and measurement (c) and (d) should be the same. For triple engine application, set the engines as shown below. If a boat has V-hull, the center motor should use longer transom motor than outside engines. C/L For twin engine application, set the engines so that the distance between the boat transom center line and the motor center line should be equal for the both engines. C/L (e) (f) (T1) (T1) (T1) Measurements (e) and (f) should be the same. Maintain a minimum distance (T1) that is the measurement between both vertical centerlines of outboard motor. Minimum distance (T1) is recommended on each model, and its data is put on the dimension item. For quad engine application, set the engines as shown below. If a boat has V-hull, inner twin engine should use longer transom motor than outside engines. C/L (T1) (T1) (T1) To be continued. 1-6

15 MOUNTING THE OUTOARD MOTOR 2. Adjust the height of outboard motor so that the anti-cavitation plate is positioned to the boat transom bottom, or lowered within 25 mm (1 in.). For planing boats, the anti-cavitation plate should be positioned to the boat transom bottom or slightly higher. Single engine application * Due to combination of a boat type and an engine type, the mount height of outboard motor varies. Therefore, the complete information is impossible to describe here. For further information, see the instructions issued by boat manufacturer, or ask to the manufacturer. 3. When the outboard motor mount position has been determined, mark the 4 symmetrical mount hole positions onto the boat transom. Make the mount holes of 13 mm (0.5 in.) vertically on the marking points. 0~25 mm (1 in.) (a) 13 mm (0.5 in.) 90 Twin engine application/quad engine application C/L * To make the mounting holes easier, use the drilling plate (P/N: or Y for US). Ex: Drilling plate ( ) 0~25 mm (1 in.) (a) 0~25 mm (1 in.) 0~25 mm (1 in.) 13 mm (0.5 in.) Twin engine application Quad engine application Triple engine application C/L (H) (H) C/L Height position of anti-cavitation plate (H): Motor transom height 0~25 mm (1 in.) (a) (a): Anti-cavitation plate 0~25 mm 0~25 mm (1 in.) (1 in.) To be continued. 1-7

16 MOUNTING THE OUTOARD MOTOR 4. Apply sealant to the mount holes, and secure the motor with supplied mount hardware. For tightening procedure, first tighten the inside nut, then the double nuts each other. NOTICE Make sure there is no clearance between boat transom and motor clamp bracket. Otherwise, the clamp bracket could break. * The upper mount bolt is usually installed to the 2nd hole from top. For above 115 (V4) and F75, select the transom mount bolt depending on the boat transom thickness. oat transom thickness (T) Mount bolt size olt P/N mm ( in.) M mm M mm ( in.) M mm M05 M mm M mm ( in.) M mm [High tension bolt] mm M mm ( in.) [High tension bolt] * High tension bolt is recommended for F350. For reference: M8: 18 Nm, 1.8 kgf m, 13 lb ft M10: 36 Nm, 3.6 kgf m, 27 lb ft M12: 52 Nm, 5.2 kgf m, 38 lb ft (a) (b) (c) (d) (b) T (a) (b) (c) (a) Mounting bolt (b) Small washer (c) Large washer (d) Nut : Sealant (b) (d) * Tighten the mounting bolts/nuts to suitable torque depending on the boat transom structure, material, design, etc. 1-8

17 MOUNTING THE OUTOARD MOTOR WATER LEVEL GUIDELINE (4-STROKE ENGINES) If you replaced 2-stroke engine to 4-stroke engine which has the same horse power, a boat tends to become stern heavy because of heavier engine weight. As a result, water line will rise and get close to the power head. This causes poor engine performance, and water could easily enter into the cylinder(s) and damage the engine. Therefore, you should consider the water level guideline when installing a 4-stroke outboard motor. When mooring a boat with a maximum boat load, maintain the minimum height (H) shown in the illustration between the water surface and the clamp bracket seating point. (H) Water surface Minimum height between water surface and bracket seating point Model Min. height (H) Carbureted F2 F mm 5.9 in Fuel injected F40 (4-cyl) F mm 3.9 in F75 and above 100 mm 3.9 in 1-9

18 MOUNTING THE OUTOARD MOTOR ADJUSTING TWIN ENGINES Set the engines in the toe-out position, and measure the distances between the two engines at the center point of the rear (a) and front (b) of the lower casing. The difference between measurement (a) and measurement (b) should not exceed 25 mm (1 in.). MAX. OAT SPEED ESTIMATION Depending on the engine power, boat length and boat weight, the maximum boat speed can be generally estimated with the calculation formula as below. V = L (PS/ ) V = Estimated maximum boat speed (km/h) L = oat length (m) *water line PS = Prop shaft output power = Displacement volume (ton) For example: oat length = 8 m (27 ft) *water line Engine power = 250 ps Displacement volume = 3 ton (3000 kg) Max. boat speed [V] = (250/3) = 62.2 km/h (38.6 mph) (b) (a) * This should be only used as a reference. The maximum boat speed varies depending on the hull design, rigging state, passengers weight, engine weight, engine position, etc. Confirm the actual boat speed by test run. * Adjustment: (b) (a) = Within 25 mm (1 in) For best result, your toe-out distance should be set so that the twin engines wake meets approximately m (25 50 ft) past the stern of the boat m (25 50 ft) 1-10

19 MOUNTING THE REMOTE OIL TANK The remote oil tank is required for 2-stroke V4 and V6 oil injection engines. Oil tank holder 250 (9.8) mm (in.) REMOTE OIL TANK DIMENSIONS 10.5 liter (2.8 US gallons) tank P/N: 6E (12.6) 180 (7.1) mm (in.) 210 (8.3) 30 (1.2) 173 (6.8) 160 (6.3) 130 (5.1) 30 (1.2) 112 (4.4) 200 (7.9) 6.5 (0.26) 170 (6.7) 40 (1.6) 25 (1.0) 200 (7.9) 230 (9.1) 18 liter (4.8 US gallons) tank P/N: 6E (20) 180 (7.1) mm (in.) NOTICE FOR MOUNTING THE REMOTE OIL TANK Follow the notifications below, for the remote oil tank installation. Mount the oil tank in as dry as possible location to avoid water entering into the oil tank. Mount in a location that will allow service to the filter located on the remote oil tank. Mount the remote oil tank lower than the engine oil tank. If the remote oil tank is mounted higher than the top of the engine because of the boat type, an optional check valve (P/N: 6R ) shown below is required. 235 (9.3) Install the check valve on the oil hose between the engine and remote oil tank to prevent siphoning of oil to the engine and spillage. Route the oil hose between the engine and the remote oil tank without pinching and kinking. 1-11

20 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSION ITEMS Symbol L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 W1 W2 W3 W4 W5 W6 A1 A2 A3 T1 Definition and Description Horizontal distance from datum point to rearmost point of power unit Horizontal distance from datum point to forefront (depends on the model) of power unit Distance from datum point to farthest point on tiller handle, when the handle is in horizontal position (in use) Horizontal distance from datum point to rearmost point of the lower case Minimum distance from transom board or its extension to forefront of the lower case, with motor fully trimmed down and steered to the full Horizontal distance from datum point to rearmost point of protrusion when motor is tilted up (overtilt position) Horizontal distance from datum point to protruded forefront when motor is tilted up (over-tilt position) Horizontal distance from datum point to lowest point of protrusion when motor is tilted up (over-tilt position) Horizontal forward protrusion of lower case from the datum line when PTT is fully trimmed down Horizontal distance from datum point to bracket shaft (bolt) center Vertical distance from datum point to lowest point of motor Vertical distance from datum point to highest point of power head Vertical distance from anti-cavitation plate undersurface to the center of propeller shaft Vertical distance from datum point to anti-cavitation plate undersurface Vertical distance from datum point to tiller handle tip when the handle is in vertical position Vertical distance from skeg tip at H1 to the lowest point of lower unit when motor is tilted up (overtilt position) Vertical distance from datum line to protruded forefront when motor is tilted up (over-tilt position) Vertical distance from datum line to lowest point of protrusion when motor is tilted up (over-tilt position) Vertical distance to the highest point of the motor when it is tilted up (over-tilt position) Vertical distance from datum point to bracket shaft (bolt) center Difference in the height of lower unit lowest point comparing to the height in the standard position and with PTT in the fully trimmed down position. Leftward protrusion from center line of motor body when looking at the front face Distance from tiller handle tip to centerline of motor body when looking at the front face Distance from centerline to left or right edge of motor body, except for levers and handles Distance from centerline to left or right end of motor body protrusion, except for levers and handles Distance from centerline to the farthest point on the body when steered to the maximum angle Distance from centerline to the farthest point on the tiller handle when steered to the maximum angle Maximum steering angle each way (symmetrical), from centerline of motor body Tilt up angle (whole rotating range to over-tilt angle including negative trim angle) Maximum negative trim angle from the vertical line through the datum point Centerline-to-centerline minimum distance of the engines in case of twin installation 1-12

21 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSION ITEMS L2 L1 A1 L3 L7 L6 A3 L4 H6 W6 W2 W3 W4 W5 W1 H11 H1 H9 H3 H4 H5 H2 H10 H7 H8 T1 L8 L10 L5 12 L9 A2 1-13

22 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA model) F2AMH F2.5AMH (F2.5MHA) w/ EPA cap F4MH (F4MHA) F5AMH F6CMH (F6MHA) F8CMH (F8MHA) Long handle F8CMH F8CWH Short handle FT8DMH Long handle FT8DE FT8DEP L1 mm (in) 315 (12.4) 315 (12.4) 409 (16.1) 430 (16.9) 430 (16.9) 430 (16.9) 430 (16.9) 430 (16.9) L2 mm (in) 93 (3.7) 93 (3.7) 130 (5.1) 122 (4.8) 122 (4.8) 122 (4.8) 122 (4.8) 122 (4.8) L3 mm (in) 309 (12.2) 309 (12.2) 341 (13.4) 608 (23.9) 498 (19.6) 608 (23.9) L4 mm (in) 215 (8.5) 215 (8.5) 259 (10.2) 355 (14.0) 355 (14.0) 367 (14.4) 367 (14.4) 367 (14.4) S 57 (2.2) 57 (2.2) 71 (2.8) 72 (2.8) 72 (2.8) L5 L 57 (2.2) 57 (2.2) 93 (3.7) 99 (3.9) 99 (3.9) 99 (3.9) 99 (3.9) 99 (3.9) mm (in) X 99 (3.9) 99 (3.9) 99 (3.9) U S 636 (25.0) 636 (25.0) 635 (25.0) 706 (27.8) 706 (27.8) L6 L 761 (30.0) 761 (30.0) 753 (29.6) 822 (32.4) 822 (32.4) 879 (34.6) 879 (34.6) 879 (34.6) mm (in) X 941 (37.0) 941 (37.0) 941 (37.0) U L7 mm (in) 366 (14.4) 388 (15.3) 383 (15.1) 271 (10.7) 271 (10.7) 271 (10.7) 271 (10.7) 271 (10.7) L8 mm (in) 167 (6.6) 167 (6.6) 134 (5.3) 139 (5.5) 139 (5.5) 139 (5.5) 139 (5.5) 225 (8.9) S L9 L mm (in) X U L10 mm (in) 75 (3.0) 57 (2.2) 63 (2.5) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) S 645 (25.4) 645 (25.4) 644 (25.4) 682 (26.9) 682 (26.9) H1 L 772 (30.4) 772 (30.4) 771 (30.4) 809 (31.9) 809 (31.9) 869 (34.2) 869 (34.2) 869 (34.2) mm (in) X 937 (36.9) 937 (36.9) 937 (36.9) U H2 mm (in) 376 (14.8) 397 (15.6) 395 (15.6) 318 (12.5) 318 (12.5) 318 (12.5) 318 (12.5) 318 (12.5) H3 mm (in) 103 (4.1) 103 (4.1) 104 (4.1) 123 (4.8) 123 (4.8) 157 (6.2) 157 (6.2) 157 (6.2) S 432 (17.0) 432 (17.0) 435 (17.1) 436 (17.2) 436 (17.2) H4 L 559 (22.0) 559 (22.0) 562 (22.1) 563 (22.2) 563 (22.2) 557 (21.9) 557 (21.9) 557 (21.9) mm (in) X 625 (24.6) 625 (24.6) 625 (24.6) U H5 mm (in) 470 (18.5) 470 (18.5) 430 (16.9) 673 (26.5) 563 (22.2) 673 (26.5) S 642 (25.3) 642 (25.3) 555 (21.9) 594 (23.4) 594 (23.4) H6 L 746 (29.4) 746 (29.4) 637 (25.1) 669 (26.3) 669 (26.3) 717 (28.2) 717 (28.2) 717 (28.2) mm (in) X 757 (29.8) 757 (29.8) 757 (29.8) U H7 mm (in) 264 (10.4) 255 (10.0) 191 (7.5) 203 (8.0) 203 (8.0) 203 (8.0) 203 (8.0) 203 (8.0) H8 mm (in) 15 (0.6) 15 (0.6) 0.6 (0.02) 5 (0.2) 5 (0.2) 5 (0.2) 5 (0.2) 5 (0.2) H9 mm (in) 406 (16.0) 406 (16.0) 503 (19.8) 529 (20.8) 529 (20.8) 529 (20.8) 529 (20.8) 529 (20.8) H10 mm (in) 32 (1.3) 32 (1.3) 39 (1.5) 32 (1.3) 32 (1.3) 32 (1.3) 32 (1.3) 32 (1.3) S H11 L mm (in) X U W1 mm (in) 140 (5.5) 140 (5.5) 181 (7.1) 159 (6.3) 169 (6.7) 172 (6.8) 177 (7.0) 177 (7.0) W2 mm (in) 205 (8.1) 205 (8.1) 222 (8.7) 199 (7.8) 206 (8.1) 199 (7.8) 135 (5.3) W3 mm (in) 139 (5.5) 139 (5.5) 159 (6.3) 159 (6.3) 159 (6.3) 159 (6.3) 159 (6.3) W4 mm (in) 135 (5.3) 135 (5.3) 153 (6.0) 159 (6.3) 159 (6.3) 159 (6.3) 159 (6.3) 159 (6.3) W5 mm (in) 325 (12.8) 286 (11.3) 286 (11.3) 286 (11.3) 286 (11.3) 271 (10.7) W6 mm (in) 425 (16.7) 619 (24.4) 536 (21.1) 619 (24.4) 271 (10.7) A1 degree A2 degree A3 degree T1 mm (in) 1-14

23 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA model) F9.9JMH (F9.9MH) F9.9JEH (F9.9EH) F9.9JWH F9.9JE (F9.9E) FT9.9LMH (T9.9MH) FT9.9LWH (T9.9EH) FT9.9LEHP (T9.9PH) FT9.9LE (T9.9E) FT9.9LEP (T9.9P) F9.9HMH F15CMH (F15MHA) F15CEH (F15EHA) F15CWH F20MH (F20MHA) F20EH (F20EHA) F20WH F20CMH F15CEHP (F15PHA) F20EHP (F20PHA) L1 mm (in) 436 (17.2) 436 (17.2) 436 (17.2) 435 (17.1) 436 (17.2) 435 (17.1) 489 (19.3) 488 (19.2) L2 mm (in) 124 (4.9) 121 (4.8) 121 (4.8) 122 (4.8) 121 (4.8) 122 (4.8) 219 (8.6) 220 (8.7) L3 mm (in) 547 (21.5) 607 (23.9) 608 (23.9) 559 (22.0) 559 (22.0) L4 mm (in) 356 (14.0) 356 (14.0) 367 (14.4) 367 (14.4) 367 (14.4) 367 (14.4) 387 (15.2) 386 (15.2) S 49 (1.9) 49 (1.9) 64 (2.5) L5 L 67 (2.6) 67 (2.6) 67 (2.6) 35 (1.4) 67 (2.6) 35 (1.4) 82 (3.2) 82 (3.2) mm (in) X 67 (2.6) 35 (1.4) 67 (2.6) 35 (1.4) U S 707 (27.8) 707 (27.8) 730 (28.7) L6 L 823 (32.4) 823 (32.4) 880 (34.6) 879 (34.6) 880 (34.6) 879 (34.6) 847 (33.3) 840 (33.1) mm (in) X 943 (37.1) 941 (37.0) 943 (37.1) 941 (37.0) U L7 mm (in) 276 (10.9) 276 (10.9) 276 (10.9) 273 (10.7) 276 (10.9) 273 (10.7) 381 (15.0) 356 (14.0) L8 mm (in) 141 (5.6) 138 (5.4) 138 (5.4) 139 (5.5) 138 (5.4) 139 (5.5) 237 (9.3) 176 (6.9) S 18 (0.7) 18 (0.7) 9 (0.4) L9 L 27 (1.1) 27 (1.1) 27 (1.1) 62 (2.4) 27 (1.1) 62 (2.4) 18 (0.7) 18 (0.7) mm (in) X 27 (1.1) 62 (2.4) 27 (1.1) U L10 mm (in) 66 (2.6) 66 (2.6) 66 (2.6) 67 (2.6) 66 (2.6) 67 (2.6) 66 (2.6) 67 (2.6) S 677 (26.7) 677 (26.7) 701 (27.6) H1 L 804 (31.7) 804 (31.7) 864 (34.0) 869 (34.2) 864 (34.0) 869 (34.2) 828 (32.6) 833 (32.8) mm (in) X 932 (36.7) 937 (36.9) 932 (36.7) 937 (36.9) U H2 mm (in) 331 (13.0) 331 (13.0) 331 (13.0) 326 (12.8) 331 (13.0) 326 (12.8) 377 (14.8) 372 (14.6) H3 mm (in) 123 (4.8) 123 (4.8) 157 (6.2) 157 (6.2) 157 (6.2) 157 (6.2) 133 (5.2) 133 (5.2) S 431 (17.0) 431 (17.0) 438 (17.2) H4 L 558 (22.0) 558 (22.0) 552 (21.7) 557 (21.9) 552 (21.7) 557 (21.9) 565 (22.2) 570 (22.4) mm (in) X 620 (24.4) 625 (24.6) 620 (24.4) 625 (24.6) U H5 mm (in) 614 (24.2) 678 (26.7) 673 (26.5) 570 (22.4) 566 (22.3) S 604 (23.8) 604 (23.8) 616 (24.3) H6 L 682 (26.9) 682 (26.9) 730 (28.7) 717 (28.2) 730 (28.7) 717 (28.2) 694 (27.3) 643 (25.3) mm (in) X 771 (30.4) 757 (29.8) 771 (30.4) 757 (29.8) U H7 mm (in) 216 (8.5) 216 (8.5) 216 (8.5) 213 (8.4) 216 (8.5) 273 (10.7) 399 (15.7) 414 (16.3) H8 mm (in) 7 (0.3) 8 (0.3) 8 (0.3) 5 (0.2) 8 (0.3) 5 (0.2) 44 (1.7) 37 (1.5) H9 mm (in) 527 (20.8) 527 (20.7) 609 (24.0) 604 (23.8) 527 (20.7) 522 (20.6) 580 (22.8) 575 (22.6) H10 mm (in) 37 (1.5) 37 (1.5) 37 (1.5) 32 (1.3) 37 (1.5) 32 (1.3) 37 (1.5) 32 (1.3) S 19 (0.7) 19 (0.7) 19 (0.7) H11 L 19 (0.7) 19 (0.7) 19 (0.7) 33 (1.3) 19 (0.7) 33 (1.3) 19 (0.7) 19 (0.7) mm (in) X 19 (0.7) 33 (1.3) 19 (0.7) 33 (1.3) U W1 mm (in) 156 (6.1) 177 (7.0) 172 (6.8) 172 (6.8) 177 (7.0) 177 (7.0) 210 (8.3) 210 (8.3) W2 mm (in) 188 (7.4) 189 (7.4) 189 (7.4) 210 (8.3) 210 (8.3) W3 mm (in) 156 (6.1) 156 (6.1) 156 (6.1) 156 (6.1) 156 (6.1) 156 (6.1) 176 (6.9) 176 (6.9) W4 mm (in) 156 (6.1) 156 (6.1) 156 (6.1) 156 (6.1) 156 (6.1) 156 (6.1) W5 mm (in) 284 (11.2) 284 (11.2) 284 (11.2) 265 (10.4) 284 (11.2) 265 (10.4) 341 (13.4) 320 (12.6) W6 mm (in) 562 (22.1) 603 (23.7) 567 (22.3) 598 (23.5) 568 (22.4) A1 degree A2 degree A3 degree T1 mm (in) 1-15

24 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA model) F9.9HE F15CE F20E (F20EA) F20CE F15CEP F20EP (F20PA) F25DMH (F25MHA) F25DEH (F25EHA) F25DWH F25DMHD (F25MH) F25DEHD (F25EH) F25DWHD F25DEHT F25DEH w/6x4 tiller handle F25DE (F25EA) F25DET (F25A) F20DET L1 mm (in) 489 (19.3) 488 (19.2) 601 (23.7) 601 (23.7) 601 (23.7) 601 (23.7) 601 (23.7) 601 (23.7) L2 mm (in) 176 (6.9) 176 (6.9) 255 (10.0) 123 (4.8) 123 (4.8) L3 mm (in) 580 (22.8) 580 (22.8) 580 (22.8) 769 (30.3) L4 mm (in) 387 (15.2) 386 (15.2) 433 (17.0) 433 (17.0) 433 (17.0) 433 (17.0) 433 (17.0) 433 (17.0) S 64 (2.5) 89 (3.5) 85 (3.3) 103 (4.1) L5 L 82 (3.2) 82 (3.2) 103 (4.1) 111 (4.4) 111 (4.4) 103 (4.1) 103 (4.1) 111 (4.4) mm (in) X 115 (4.5) 124 (4.9) 124 (4.9) U S 730 (28.7) 727 (28.6) 761 (30.0) 880 (34.6) L6 L 847 (33.3) 840 (33.1) 880 (34.6) 875 (34.4) 875 (34.4) 880 (34.6) 880 (34.6) 875 (34.4) mm (in) X 960 (37.8) 951 (37.4) 951 (37.4) U L7 mm (in) 321 (12.6) 309 (12.2) 378 (14.9) 353 (13.9) 353 (13.9) 378 (14.9) 378 (14.9) 353 (13.9) L8 mm (in) 184 (7.2) 188 (7.4) 189 (7.4) 197 (7.8) 197 (7.8) 159 (6.3) 147 (5.8) 150 (5.9) S 9 (0.4) 18 (0.7) 15 (0.6) 6 (0.2) L9 L 18 (0.7) 18 (0.7) 6 (0.2) 14 (0.6) 14 (0.6) 6 (0.2) 14 (0.6) mm (in) X 1 (0.05) 10 (0.4) 10 (0.4) U L10 mm (in) 66 (2.6) 67 (2.6) 65 (2.6) 65 (2.6) 65 (2.6) 65 (2.6) 65 (2.6) 65 (2.6) S 701 (27.6) 706 (27.8) 707 (27.8) 834 (32.8) H1 L 828 (32.6) 833 (32.8) 834 (32.8) 834 (32.8) 834 (32.8) 834 (32.8) 834 (32.8) 834 (32.8) mm (in) X 920 (36.2) 920 (36.2) 920 (36.2) U H2 mm (in) 377 (14.8) 372 (14.6) 450 (17.7) 450 (17.7) 450 (17.7) 450 (17.7) 450 (17.7) 450 (17.7) H3 mm (in) 133 (5.2) 133 (5.2) 144 (5.7) 144 (5.7) 144 (5.7) 144 (5.7) 144 (5.7) 144 (5.7) S 438 (17.2) 443 (17.4) 423 (16.7) 550 (21.7) H4 L 565 (22.2) 570 (22.4) 550 (21.7) 550 (21.7) 550 (21.7) 550 (21.7) 550 (21.7) 550 (21.7) mm (in) X 635 (25.0) 636 (25.0) 636 (25.0) U H5 mm (in) 766 (30.2) S 616 (24.3) 574 (22.6) 667 (26.3) 748 (29.4) H6 L 694 (27.3) 643 (25.3) 748 (29.4) 665 (26.2) 665 (26.2) 748 (29.4) 748 (29.4) 665 (26.2) mm (in) X 803 (31.6) 711 (28.0) 711 (28.0) U H7 mm (in) 218 (8.6) 230 (9.1) 258 (10.2) 282 (11.1) 282 (11.1) 258 (10.2) 258 (10.2) 282 (11.1) H8 mm (in) 32 (1.3) 28 (1.1) 41 (1.6) 26 (1.0) 26 (1.0) 47 (1.9) 12 (0.5) 22 (0.9) H9 mm (in) 580 (22.8) 575 (22.6) 705 (27.8) 706 (27.8) 706 (27.8) 705 (27.8) 705 (27.8) 706 (27.8) H10 mm (in) 37 (1.5) 32 (1.3) 43 (1.7) 43 (1.7) 43 (1.7) 43 (1.7) 43 (1.7) 43 (1.7) S 19 (0.7) 19 (0.7) 23 (0.9) 22 (0.9) H11 L 19 (0.7) 19 (0.7) 22 (0.9) 18 (0.7) 18 (0.7) 22 (0.9) 22 (0.9) 18 (0.7) mm (in) X 22 (0.9) 17 (0.7) 17 (0.7) U W1 mm (in) 210 (8.3) 210 (8.3) 199 (7.8) 199 (7.8) 199 (7.8) 199 (7.8) 199 (7.8) 199 (7.8) W2 mm (in) 213 (8.4) 213 (8.4) 213 (8.4) 128 (5.0) 213 (8.4) W3 mm (in) 180 (7.1) 180 (7.1) W4 mm (in) W5 mm (in) 341 (13.4) 320 (12.6) 387 (15.2) 387 (15.2) 387 (15.2) 387 (15.2) 387 (15.2) 387 (15.2) W6 mm (in) 604 (23.8) 604 (23.8) 604 (23.8) 665 (26.2) 604 (23.8) A1 degree A2 degree 71 S:63 / L: A3 degree 4 S:0 / L: T1 mm (in) 1-16

25 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA model) FT25FET (T25A) F30EHT F40FEHT F30EHD (F30EHA) F40FEHD (F40EHA) F30ET (F30A) F40FET (F40A) F40FED (F40EA) F40GET F40HET F50HET (F50) F60FET (F60) F50HED L1 mm (in) 601 (23.7) 583 (23.0) 583 (23.0) 583 (23.0) 583 (23.0) 591 (23.3) 584 (23.0) 584 (23.0) L2 mm (in) 134 (5.3) 235 (9.3) 235 (9.3) 134 (5.3) 134 (5.3) 122 (4.8) 122 (4.8) 122 (4.8) L3 mm (in) 779 (30.7) 779 (30.7) L4 mm (in) 522 (20.6) 522 (20.6) 522 (20.6) 522 (20.6) 522 (20.6) 582 (22.9) 533 (21.0) 533 (21.0) S 77 (3.0) 77 (3.0) 77 (3.0) L5 L 66 (2.6) 66 (2.6) 66 (2.6) 66 (2.6) 66 (2.6) 67 (2.6) 97 (3.8) 97 (3.8) mm (in) X 66 (2.6) 66 (2.6) 66 (2.6) 121 (4.8) U S 816 (32.1) 817 (32.2) 816 (32.1) L6 L 924 (36.4) 925 (36.4) 923 (36.3) 924 (36.4) 923 (36.3) 1000 (39.4) 932 (36.7) 930 (36.6) mm (in) X 1025 (40.4) 1024 (40.3) 1025 (40.4) 1036 (40.8) U L7 mm (in) 338 (13.3) 345 (13.6) 342 (13.5) 345 (13.6) 342 (13.5) 421 (16.6) 417 (16.4) 406 (16.0) L8 mm (in) 158 (6.2) 177 (7.0) 178 (7.0) 158 (6.2) 158 (6.2) 152 (6.0) 147 (5.8) 148 (5.8) S 29 (1.1) 29 (1.1) 29 (1.1) L9 L 29 (1.1) 29 (1.1) 29 (1.1) 29 (1.1) 29 (1.1) 26 (1.0) 0 (0.0) 0 (0.0) mm (in) X 29 (1.1) 29 (1.1) 29 (1.1) 0 (0.0) U L10 mm (in) 65 (2.6) 65 (2.6) 65 (2.6) 65 (2.6) 65 (2.6) 62 (2.4) 62 (2.4) 62 (2.4) S 757 (29.8) 757 (29.8) 757 (29.8) H1 L 879 (34.6) 879 (34.6) 879 (34.6) 879 (34.6) 879 (34.6) 915 (36.0) 870 (34.3) 870 (34.3) mm (in) X 993 (39.1) 993 (39.1) 993 (39.1) 984 (38.7) U H2 mm (in) 433 (17.0) 471 (18.5) 471 (18.5) 471 (18.5) 471 (18.5) 561 (22.1) 545 (21.5) 545 (21.5) H3 mm (in) 175 (6.9) 175 (6.9) 175 (6.9) 175 (6.9) 175 (6.9) 191 (7.5) 175 (6.9) 175 (6.9) S 414 (16.3) 414 (16.3) 414 (16.3) H4 L 536 (21.1) 536 (21.1) 536 (21.1) 536 (21.1) 536 (21.1) 534 (21.0) 527 (20.7) 527 (20.7) mm (in) X 650 (25.6) 650 (25.6) 650 (25.6) 641 (25.2) U H5 mm (in) 770 (30.3) 770 (30.3) S 594 (23.4) 606 (23.9) 594 (23.4) H6 L 667 (26.3) 667 (26.3) 660 (26.0) 667 (26.3) 660 (26.0) 749 (29.5) 708 (27.9) 682 (26.9) mm (in) X 728 (28.7) 720 (28.3) 728 (28.7) 774 (30.5) U H7 mm (in) 274 (10.8) 306 (12.0) 304 (12.0) 306 (12.0) 304 (12.0) 371 (14.6) 354 (13.9) 354 (13.9) H8 mm (in) 14 (0.6) 44 (1.7) 43 (1.7) 14 (0.6) 15 (0.6) 26 (1.0) 22 (0.9) 25 (1.0) H9 mm (in) 698 (27.5) 695 (27.4) 695 (27.4) 695 (27.4) 695 (27.4) 741 (29.2) 759 (29.9) 762 (30.0) H10 mm (in) 43 (1.7) 43 (1.7) 43 (1.7) 43 (1.7) 43 (1.7) 49 (1.9) 49 (1.9) 49 (1.9) S 19 (0.7) 19 (0.7) 19 (0.7) H11 L 19 (0.7) 19 (0.7) 19 (0.7) 19 (0.7) 19 (0.7) 29 (1.1) 24 (0.9) 24 (0.9) mm (in) X 19 (0.7) 19 (0.7) 19 (0.7) 24 (0.9) U W1 mm (in) 199 (7.8) 192 (7.6) 192 (7.6) 192 (7.6) 192 (7.6) 193 (7.6) 192 (7.6) 192 (7.6) W2 mm (in) 128 (5.0) 128 (5.0) W3 mm (in) W4 mm (in) W5 mm (in) 376 (14.8) 364 (14.3) 364 (14.3) 364 (14.3) 364 (14.3) 363 (14.3) 360 (14.2) 360 (14.2) W6 mm (in) 654 (25.7) 654 (25.7) A1 degree A2 degree A3 degree T1 mm (in) 560 (22.0) 560 (22.0) 1-17

26 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA model) F50DET F50HEHD F50HEHT (F50H) F60FEHT (F60H) FT50JET (T50) FT60GET (T60) FT50CET FT60GEHT FT50CEHD FT60GEHD L1 mm (in) 576 (22.7) 584 (23.0) 584 (23.0) 584 (23.0) 576 (22.7) 584 (23.0) 576 (22.7) 584 (23.0) L2 mm (in) 142 (5.6) 225 (8.9) 225 (8.9) 122 (4.8) 142 (5.6) 225 (8.9) 272 (10.7) 225 (8.9) L3 mm (in) 788 (31.0) 788 (31.0) 788 (31.0) 797 (31.2) 778 (30.6) L4 mm (in) 532 (20.9) 533 (21.0) 533 (21.0) 561 (22.1) 560 (22.1) 561 (22.1) 560 (22.1) 561 (22.1) S L5 L 97 (3.8) 97 (3.8) 97 (3.8) 98 (3.9) 98 (3.9) 98 (3.9) 98 (3.9) 67 (2.6) mm (in) X 114 (4.5) 85 (3.4) 85.0 (3.35) 98 (3.9) U S L6 L 933 (36.7) 930 (36.6) 932 (36.7) 996 (39.2) 991 (39.0) 996 (39.2) 989 (38.9) 995 (39.2) mm (in) X 1099 (43.3) 1095 (43.1) 1092 (43.0) 1097 (43.2) U L7 mm (in) 407 (16.0) 406 (16.0) 417 (16.4) 417 (16.4) 407 (16.0) 417 (16.4) 397 (15.6) 407 (16.0) L8 mm (in) 148 (5.8) 168 (6.6) 165 (6.5) 147 (5.8) 148 (5.8) 165 (6.5) 189 (7.2) 168 (6.6) S L9 L 0.6 (0.02) 0 (0.0) 0 (0.0) 0 (0.0) 1.0 (0.04) 0 (0.0) 0.8 (0.03) 0 (0.0) mm (in) X 0 (0.0) 0 (0.0) 16.0 (0.63) 0 (0.0) 16 (0.63) 0 (0.0) U L10 mm (in) 63 (2.5) 62 (2.4) 62 (2.4) 62 (2.4) 63 (2.5) 62 (2.4) 63 (2.5) 62 (2.4) S H1 L 876 (34.5) 870 (34.3) 870 (34.3) 910 (35.8) 917 (36.1) 910 (35.8) 917 (36.1) 910 (35.8) mm (in) X 1024 (40.3) 1026 (40.4) 1026 (40.4) 1025 (40.4) U H2 mm (in) 519 (20.4) 545 (21.5) 545 (21.5) 545 (21.5) 519 (20.4) 545 (21.5) 519 (20.4) 545 (21.5) H3 mm (in) 175 (6.9) 175 (6.9) 175 (6.9) 191 (7.5) 194 (7.6) 191 (7.5) 194 (7.6) 191 (7.5) S H4 L 533 (21.0) 527 (20.7) 527 (20.7) 530 (20.9) 536 (21.1) 530 (20.9) 533 (21.0) 530 (20.9) mm (in) X 644 (25.4) 645 (25.4) 645 (25.4) 644 (25.4) U H5 mm (in) 790 (31.1) 790 (31.1) 790 (31.1) 680 (26.8) 790 (31.1) S H6 L 711 (28.0) 682 (26.9) 708 (27.9) 746 (29.4) 750 (29.5) 746 (29.4) 723 (28.5) 720 (28.3) mm (in) X 812 (32.0) 813 (32.0) 783 (30.8) 782 (30.8) U H7 mm (in) 327 (12.9) 354 (13.9) 354 (13.9) 354 (13.9) 327 (12.9) 354 (13.9) 330 (13.0) 354 (13.9) H8 mm (in) 3.5 (0.14) 33 (1.3) 37 (1.5) 22 (0.9) 3.5 (0.14) 37 (1.5) 110 (4.3) 34 (1.3) H9 mm (in) 733 (28.9) 713 (28.1) 759 (29.9) 759 (29.9) 733 (28.9) 759 (29.9) 738 (29.1) 763 (30.0) H10 mm (in) 44 (1.7) 49 (1.9) 49 (1.9) 49 (1.9) 44 (1.7) 49 (1.9) 44 (1.7) 49 (1.9) S H11 L 24 (0.9) 24 (0.9) 24 (0.9) 24 (0.9) 28 (1.1) 24 (0.9) 28 (1.1) 29 (1.1) mm (in) X 24 (0.9) 27 (1.0) 27 (1.0) 24 (0.9) U W1 mm (in) 181 (7.1) 192 (7.6) 192 (7.6) 192 (7.6) 181 (7.1) 192 (7.6) 181 (7.1) 192 (7.6) W2 mm (in) 137 (5.4) 137 (5.4) 137 (5.4) 213 (8.4) 137 (5.4) W3 mm (in) 181 (7.1) 181 (7.1) 181 (7.13) W4 mm (in) W5 mm (in) 345 (13.6) 360 (14.2) 360 (14.2) 360 (14.2) 345 (13.6) 360 (14.2) 345 (13.6) 360 (14.2) W6 mm (in) 672 (26.5) 672 (26.5) 672 (26.5) 738 (29.1) 672 (26.5) A1 degree A2 degree A3 degree T1 mm (in) 560 (22.0) 560 (22.0) 560 (22.0) 560 (22.0) 560 (22.0) 1-18

27 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA model) F70AET (F70A) F40GET F70AET (F70A) w/6x4 tiller handle F75ET (F75A) F80ET F90ET (F90A) F100DET F75ET (F75A) F80ET F90ET (F90A) F100DET w/6x4 tiller handle F75CED F75CEHD F100EHT F100EHD F95AET F100ET F/FL115AET (F/LF115A) L1 mm (in) 591 (23.3) 591 (23.3) 651 (25.6) 651 (25.6) 664 (26.1) 664 (26.1) 664 (26.1) 665 (26.2) L2 mm (in) 122 (4.8) 225 (8.9) 171 (6.7) 247 (9.7) 161 (6.3) 324 (12.8) 161 (6.3) 161 (6.3) L3 mm (in) 788 (31.0) 822 (32.4) 844 (33.2) L4 mm (in) 582 (22.9) 582 (22.9) 574 (22.6) 574 (22.6) 631 (24.8) 631 (24.8) 631 (24.8) 631 (24.8) S L5 L 67 (2.6) 67 (2.6) 63 (2.5) 63 (2.5) 79 (3.1) 79 (3.1) 69 (2.7) 69 (2.7) mm (in) X 67 (2.6) 67 (2.6) 63 (2.5) 63 (2.5) 87 (3.4) 87 (3.4) 76 (3.0) 89 (3.5) U S L6 L 1000 (39.4) 1000 (39.4) 998 (39.3) 998 (39.3) 1005 (39.6) 1005 (39.6) 1005 (39.6) 1005 (39.6) mm (in) X 1103 (43.4) 1103 (43.4) 1115 (43.9) 1115 (43.9) 1118 (44.0) 1118 (44.0) 1122 (44.2) 1122 (44.2) U L7 mm (in) 421 (16.6) 421 (16.6) 527 (20.7) 527 (20.7) 504 (19.8) 504 (19.8) 536 (21.9) 555 (21.9) L8 mm (in) 152 (6.0) 165 (6.5) 164 (6.5) 108 (4.3) 168 (6.6) 208 (8.2) 158 (6.2) 158 (6.2) S L9 L 26 (1.0) 26 (1.0) 28 (1.1) 28 (1.1) 19 (0.7) 19 (0.7) 25 (1.0) 25 (1.0) mm (in) X 26 (1.0) 26 (1.0) 28 (1.1) 28 (1.1) 15 (0.6) 15 (0.6) 25 (1.0) 33 (1.3) U L10 mm (in) 62 (2.4) 62 (2.4) 62 (2.4) 62 (2.4) 75 (3.0) 75 (3.0) 75 (3.0) 75 (3.0) S H1 L 915 (36.0) 915 (36.0) 917 (36.1) 917 (36.1) 929 (36.6) 929 (36.6) 929 (36.6) 929 (36.6) mm (in) X 1029 (40.5) 1029 (40.5) 1044 (41.1) 1044 (41.1) 1056 (41.6) 1056 (41.6) 1056 (41.6) 1056 (41.6) U H2 mm (in) 561 (22.1) 561 (22.1) 666 (26.2) 666 (26.2) 667 (26.3) 667 (26.3) 666 (26.2) 681 (26.8) H3 mm (in) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) S H4 L 534 (21.0) 534 (21.0) 536 (21.1) 536 (21.1) 516 (20.3) 516 (20.3) 516 (20.3) 516 (20.3) mm (in) X 648 (25.5) 648 (25.5) 663 (26.1) 663 (26.1) 643 (25.3) 643 (25.3) 643 (25.3) 643 (25.3) U H5 mm (in) 790 (31.1) 784 (30.9) 764 (30.1) S H6 L 749 (29.5) 749 (29.5) 766 (30.2) 766 (30.2) 709 (27.9) 709 (27.9) 776 (30.6) 773 (30.4) mm (in) X 815 (32.1) 815 (32.1) 842 (33.1) 842 (33.1) 776 (30.6) 776 (30.6) 854 (33.6) 850 (33.5) U H7 mm (in) 371 (14.6) 371 (14.6) 366 (14.4) 366 (14.4) 401 (15.8) 401 (15.8) 388 (15.3) 406 (16.0) H8 mm (in) 26 (1.0) 37 (1.5) 27 (1.1) 49 (1.9) 4 (0.2) 93 (3.7) 14 (0.6) 14 (0.6) H9 mm (in) 741 (29.2) 741 (29.2) 857 (33.7) 857 (33.7) 892 (35.1) 892 (35.1) 877 (34.5) 879 (34.6) H10 mm (in) 49 (1.9) 49 (1.9) 49 (1.9) 49 (1.9) 44 (1.7) 44 (1.7) 44 (1.7) 44 (1.7) S H11 L 29 (1.1) 29 (1.1) 25 (1.0) 25 (1.0) 17 (0.7) 17 (0.7) 25 (1.0) 25 (1.0) mm (in) X 29 (1.1) 29 (1.1) 24 (0.9) 24 (0.9) 17 (0.7) 17 (0.7) 25 (1.0) 25 (1.0) U W1 mm (in) 193 (7.6) 193 (7.6) 240 (9.4) 240 (9.4) 243 (9.6) 243 (9.6) 243 (9.6) 249 (9.8) W2 mm (in) 137 (5.4) 137 (5.4) 96 (3.8) W3 mm (in) W4 mm (in) W5 mm (in) 363 (14.3) 363 (14.3) 405 (15.9) 405 (15.9) 384 (15.1) 384 (15.1) 384 (15.1) 392 (15.4) W6 mm (in) 676 (26.6) 633 (24.9) 578 (22.8) A1 degree A2 degree A3 degree T1 mm (in) 560 (22.0) 660 (26.0) 660 (26.0) 660 (26.0) 660 (26.0) 660 (26.0) 1-19

28 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Global model (US, CA model) F115AEHT Symbol L1 mm (in) 662 (26.1) L2 mm (in) L3 mm (in) L4 mm (in) 631 (24.8) S L5 L mm (in) X 104 (4.1) U S L6 L mm (in) X 1122 (44.2) U L7 mm (in) 555 (21.9) L8 mm (in) S L9 L mm (in) X 16 (0.6) U L10 mm (in) 75 (3.0) S H1 L mm (in) X 1056 (41.6) U H2 mm (in) 681 (26.8) H3 mm (in) 191 (7.5) S H4 L mm (in) X 643 (25.3) U H5 mm (in) S H6 L mm (in) X 850 (33.5) U H7 mm (in) 404 (15.9) H8 mm (in) H9 mm (in) 879 (34.6) H10 mm (in) 45 (1.8) S H11 L mm (in) X 14 (0.6) U W1 mm (in) 246 (9.7) W2 mm (in) W3 mm (in) W4 mm (in) W5 mm (in) 388 (15.3) W6 mm (in) A1 degree 30 A2 degree 68 A3 degree 2 T1 mm (in) 1-20

29 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA, ANZ model) F/FL115ET (F/LF115) F115EHT F/FL150AET (F/LF150A) F/FL150ET F150CET (VF150A) F165AET L-transom F175AET (F175A) F/FL200FET (F/LF200) F/FL200GET (F/LF200CA) F/FL200CET (F/LF200A) F/FL225ET (F/LF225A) F/FL250AET (F/LF250A) F/FL200ET F/FL250GET F225CET L-transom F200DET (VF200LA) F225DET (VF225LA) F250CET (VF250LA) F225GET F250FET F275AET L-transom L1 mm (in) 690 (27.2) 690 (27.2) 698 (27.5) 722 (28.4) 722 (28.4) 651 (25.6) 664 (26.1) 741 (29.2) L2 mm (in) 127 (5.0) 300 (11.8) 164 (6.5) 198 (7.8) 198 (7.8) 219 (8.6) 206 (8.1) 218 (8.6) L3 mm (in) L4 mm (in) 631 (24.8) 631 (24.8) 646 (25.4) 646 (25.4) 646 (25.4) 673 (26.5) 685 (27.0) 688 (27.1) S L5 L 63 (2.5) 63 (2.5) 60 (2.5) 53 (2.1) 53 (2.1) 62 (2.4) 54 (2.1) mm (in) X 81 (3.2) 81 (3.2) 80 (3.2) 63 (2.5) 59 (2.3) U 59 (2.3) S L6 L 1006 (39.6) 1006 (39.6) 1032 (40.6) 1033 (40.7) 1033 (40.7) 1043 (41.1) 1033 (40.7) mm (in) X 1122 (44.2) 1122 (44.2) 1148 (45.2) 1149 (45.2) 1115 (45.5) U 1272 (50.1) L7 mm (in) 561 (22.1) 561 (22.1) 629 (24.8) 639 (25.2) 639 (25.2) 619 (24.4) 615 (24.2) 651 (25.6) L8 mm (in) 135 (5.3) 121 (4.8) 162 (6.4) 163 (6.4) 163 (6.4) 230 (9.1) 226 (8.9) 237 (9.3) S L9 L 32 (1.3) 32 (1.3) 35 (1.4) 42 (1.7) 42 (1.7) 18 (0.7) 81 (3.2) mm (in) X 41 (1.6) 41 (1.6) 43 (1.8) 51 (2.0) 52 (2.0) U 59 (2.3) L10 mm (in) 75 (3.0) 75 (3.0) 75 (3.0) 75 (3.0) 75 (3.0) 75 (3.0) 75 (3.0) 75 (3.0) S H1 L 929 (36.6) 929 (36.6) 946 (37.2) 946 (37.2) 946 (37.2) 951 (37.4) 932 (36.7) mm (in) X 1056 (41.6) 1056 (41.6) 1073 (42.2) 1073 (42.2) 1078 (42.4) U 1205 (47.4) H2 mm (in) 700 (27.6) 700 (27.6) 769 (31.3) 796 (31.3) 796 (31.3) 752 (29.6) 754 (29.7) 817 (32.2) H3 mm (in) 191 (7.5) 191 (7.5) 210 (8.3) 210 (8.3) 210 (8.3) 216 (8.5) 216 (8.5) 216 (8.5) S H4 L 516 (20.3) 516 (20.3) 516 (20.3) 516 (20.3) 516 (20.3) 516 (20.3) 493 (19.4) mm (in) X 643 (25.3) 643 (25.3) 643 (25.3) 643 (25.3) 643 (25.3) U 770 (30.3) H5 mm (in) 782 (30.8) S H6 L 764 (30.1) 764 (30.1) 787 (31.0) 774 (30.5) 774 (30.5) 779 (30.7) 715 (28.1) mm (in) X 840 (33.1) 840 (33.1) 864 (34.0) 849 (33.4) 847 (33.3) U 924 (36.4) H7 mm (in) 429 (16.9) 429 (16.9) 455 (18.0) 501 (19.7) 501 (19.7) 387 (15.2) 399 (15.7) 507 (20.0) H8 mm (in) 15 (0.6) 53 (2.1) 16 (0.6) 14 (0.6) 14 (0.6) 39 (1.5) 26 (1.0) 33 (1.3) H9 mm (in) 877 (34.5) 877 (34.5) 915 (36.2) 928 (36.5) 928 (36.5) 902 (35.5) 915 (36.0) 1008 (39.7) H10 mm (in) 45 (1.8) 45 (1.8) 45 (1.8) 45 (1.8) 45 (1.8) 45 (1.8) 45 (1.8) 45 (1.8) S H11 L 31 (1.2) 31 (1.2) 27 (1.1) 33 (1.3) 33 (1.3) 26 (1.0) 35 (1.4) mm (in) X 31 (1.2) 31 (1.2) 27 (1.1) 32(1.3) 25 (1.0) U 25 (1.0) W1 mm (in) 262 (10.3) 262 (10.3) 256 (10.1) 274 (10.8) 274 (10.8) 317 (12.5) 318 (12.5) 332 (13.1) W2 mm (in) 137 (5.4) W3 mm (in) W4 mm (in) W5 mm (in) 422 (16.6) 422 (16.6) 433 (17.1) 425 (16.7) 425 (16.7) 453 (17.8) 464 (18.3) 496 (19.5) W6 mm (in) 665 (26.2) A1 degree A2 degree A3 degree T1 mm (in) 660 (26.0) 660 (26.0) 660 (26.0) 660 (26.0) 724 (28.5) 1-21

30 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (4-STROKE) Symbol Global model (US, CA, ANZ model) F/FL225FET (F/LF225CA) F/FL250DET (F/LF250CA) F/FL300ET (F/LF300CA) F/FL350AET (F/LF350C) L1 mm (in) 728 (28.7) 776 (30.6) L2 mm (in) 230 (9.1) 255 (10.0) L3 mm (in) L4 mm (in) 673 (26.5) 732 (28.8) S L5 L mm (in) X 59 (2.3) 48.4 (1.9) U 59 (2.3) 48.4 (1.9) S L6 L mm (in) X 1155 (45.5) 1193 (47.0) U 1272 (50.1) 1310 (51.6) L7 mm (in) 639 (25.2) 712 (28.0) L8 mm (in) 240 (9.4) 258 (10.2) S L9 L mm (in) X 53 (2.1) 56 (2.2) U 59 (2.3) 62 (2.4) L10 mm (in) 75 (3.0) 73 (2.9) S H1 L mm (in) X 1078 (42.4) 1098 (43.2) U 1205 (47.4) 1225 (48.2) H2 mm (in) 812 (32.0) 909 (35.8) H3 mm (in) 216 (8.5) 229 (9.0) S H4 L mm (in) X 643 (25.3) 637 (25.1) U 770 (30.3) 764 (30.1) H5 mm (in) S H6 L mm (in) X 847 (33.3) 864 (34.0) U 924 (36.4) 941 (37.0) H7 mm (in) 510 (20.1) 588 (23.1) H8 mm (in) 48 (1.9) 65 (2.6) H9 mm (in) 951 (37.4) 1041 (41.0) H10 mm (in) 45 (1.8) 49 (1.9) S H11 L mm (in) X 25 (1.0) 26 (1.0) U 25 (1.0) 26 (1.0) W1 mm (in) 317 (12.5) 317 (12.5) W2 mm (in) W3 mm (in) W4 mm (in) W5 mm (in) 454 (17.9) (18.7) W6 mm (in) A1 degree A2 degree A3 degree 3 3 T1 mm (in) 724 (28.5) (28.5) 1-22

31 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (2-STROKE) Symbol Global model (US, CA model) 2CMH 3AMH 4ACMH 5CMH 5CSMH 6CMH 8CMH E8DMH EK8DMH 15FMH E9.9DMH E15DMH EK9.9DMH EK15DMH EK9.9JMH EK15PMH 20DMH 25NWC 25NMH 25NMHO L1 mm (in) 275 (10.8) 311 (12.2) 344 (13.5) 363 (14.3) 346 (13.6) 393 (15.5) 405 (15.9) 428 (16.9) L2 mm (in) 122 (4.8) 107 (4.2) 145 (5.7) 114 (4.5) 180 (7.1) 180 (7.1) 165 (6.5) 185 (7.3) L3 mm (in) 328 (12.9) 317 (12.5) 333 (13.1) 439 (17.3) 372 (14.6) 479 (18.9) 473 (18.6) 508 (20.0) L4 mm (in) 164 (6.5) 223 (8.8) 252 (9.9) 359 (14.1) 268 (10.6) 355 (14.0) 357 (14.0) 402 (15.8) S 34 (1.3) 16 (0.6) 16 (0.6) 121 (4.8) 23 (0.9) 78 (3.1) 79 (3.1) 79 (3.1) L 24 (0.9) 126 (5.0) 23 (0.9) 104 (4.1) 78 (3.1) 106 (4.2) L5 Y mm (in) X 126 (5.0) 23 (0.9) 78 (3.1) U 134 (5.3) S 589 (23.2) 636 (25.0) 635 (25.0) 705 (27.8) 657 (25.9) 718 (28.3) 708 (27.9) 739 (29.1) L 758 (29.8) 826 (32.5) 782 (30.8) 831 (32.7) 821 (32.3) 852 (33.5) L6 Y mm (in) X 947 (37.3) U L7 mm (in) 276 (10.9) 311 (12.2) 331 (13.0) 287 (11.3) 354 (13.9) 314 (12.4) 334 (13.1) 337 (13.3) L8 mm (in) 142 (5.6) 156 (6.1) 148 (5.8) 154 (6.1) 207 (8.1) 263 (10.4) 165 (6.5) 242 (9.5) S 0 (0.0) L 4 (0.2) L9 Y mm (in) X 14 (0.5) U L10 mm (in) 50 (2.0) 68 (2.7) 68 (2.7) 65 (2.5) 45 (1.8) 75 (3.0) 73 (2.9) 78 (3.1) S 614 (24.2) 654 (25.7) 653 (25.7) 682 (26.9) 685 (27.0) 705 (27.8) 706 (27.8) 703 (27.7) L 780 (30.7) 809 (31.9) 825 (32.5) 832 (32.8) 833 (32.8) 830 (32.7) H1 Y mm (in) X 975 (38.4) U H2 mm (in) 302 (11.9) 343 (13.5) 358 (14.1) 295 (11.6) 359 (14.1) 335 (13.2) 356 (14.0) 365 (14.4) H3 mm (in) 100 (3.9) 103 (4.1) 105 (4.1) 123 (4.8) 122 (4.8) 135 (5.3) 34 (1.4) 144 (5.7) S 417 (16.4) 441 (17.4) 444 (17.5) 436 (17.2) 442 (17.4) 440 (17.3) 441 (17.4) 419 (16.5) L 571 (22.5) 563 (22.2) 582 (22.9) 567 (22.3) 568 (22.4) 546 (21.5) H4 Y mm (in) X 710 (27.9) U H5 mm (in) 462 (18.2) 484 (19.1) 396 (15.6) 462 (18.2) 415 (16.3) 467 (18.4) 474 (18.7) 491 (19.3) S 503 (19.8) 621 (24.4) 623 (24.5) 668 (26.3) 497 (19.6) 572 (22.5) 569 (22.4) 586 (23.1) L 719 (28.3) 758 (29.8) 574 (22.6) 641 (25.2) 638 (25.2) 655 (25.8) H6 Y mm (in) X 714 (28.1) U H7 mm (in) 38 (1.5) 342 (13.5) 104 (4.1) 110 (4.3) 86 (3.4) 138 (5.4) 186 (7.3) H8 mm (in) 12 (0.5) 9 (0.35) 30 (1.2) 2.0 (0.08) 51 (2.0) 19 (0.7) 24 (0.9) 24 (0.9) H9 mm (in) 397 (15.6) 419 (16.5) 459 (18.1) 470 (18.5) 465 (18.3) 526 (20.7) 555 (21.9) 584 (23.0) H10 mm (in) 27 (1.0) 30 (1.2) 30 (1.2) 32 (1.3) 26 (1.0) 34 (1.3) 34 (1.4) 41 (1.6) S L H11 Y mm (in) X U W1 mm (in) 151 (5.9) 108 (4.3) 144 (5.7) 150 (5.9) 136 (5.4) 143 (5.6) 173 (6.8) W2 mm (in) 125 (4.9) 181 (7.1) 178 (7.0) 193 (7.6) 192 (7.6) 189 (7.4) 206 (8.1) W3 mm (in) 89 (3.5) 105 (4.1) 134 (5.3) 137 (5.4) 129 (5.1) 143 (5.6) 152 (6.0) W4 mm (in) 158 (6.2) 185 (7.3) 177 (7.0) W5 mm (in) 283 (11.1) 280 (11.0) 280 (11.0) 296 (11.7) W6 mm (in) 551 (21.7) 497 (19.6) 493 (19.4) 528 (20.8) A1 degree (P)/40(S) A2 degree A3 degree 4 T1 mm (in) 1-23

32 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (2-STROKE) Symbol Global model (US, CA model) E/25MH 25WC 25XMH E/30HMH 30HWH 30HWC EK25MH EK25CMH 25W 30HW 30DMH 30DMHO 30DEO 30DETO E40GWH E40GMH EK40GMH E40JMH E40JWH EK40JMH E40JW L1 mm (in) 429 (16.9) 429 (16.9) 465 (18.3) 465 (18.3) 489 (19.2) 504 (19.8) 504 (19.8) 504 (19.8) L2 mm (in) 180 (7.1) 180 (7.09) 198 (7.8) 114 (4.5) 89 (3.5) 188 (7.4) 188 (7.4) 188 (7.4) L3 mm (in) 420 (16.5) 497 (19.6) 493 (19.4) 493 (19.4) L4 mm (in) 385 (15.2) 385 (15.2) 496 (19.5) 496 (19.5) 520 (20.5) 421 (16.6) 421 (16.6) 478 (18.8) S 61 (2.4) 85 (3.3) 85 (3.3) 94 (3.7) 94 (3.7) L 83 (3.3) 83 (3.3) 90 (3.5) 90 (3.5) 103 (4.1) 94 (3.7) 94 (3.7) 94 (3.7) L5 Y mm (in) 99 (3.9) 94 (3.7) X 83 (3.3) U S 736 (29.0) 752 (29.6) 752 (29.6) 784 (30.9) 784 (30.9) L 854 (33.6) 854 (33.6) 859 (33.8) 859 (33.8) 870 (34.2) 897 (35.3) 897 (35.3) 910 (35.8) L6 Y mm (in) 895 (35.2) 943 (37.1) X 933 (36.7) U L7 mm (in) 405 (16.0) 405 (15.9) 387 (15.2) 375 (14.8) 356 (14.0) 427 (16.8) 427 (16.8) 427 (16.8) L8 mm (in) 195 (7.7) 195 (7.7) 228 (9.0) 173 (6.8) 158 (6.2) 193 (7.6) 193 (7.6) 193 (7.6) S L L9 Y mm (in) X U L10 mm (in) 74.2 (2.9) 74.2 (2.9) 73 (2.9) 73 (2.9) 65 (2.6) 72 (2.8) 72 (2.8) 72 (2.8) S 707 (27.8) 712 (28.0) 712 (28.0) 771 (30.4) 771 (30.4) L 834 (32.8) 834 (32.8) 833 (32.8) 833 (32.8) 835 (32.9) 898 (35.4) 898 (35.4) 891 (35.1) H1 Y mm (in) 874 (34.4) 948 (37.3) X 920 (36.2) U H2 mm (in) 439 (17.3) 439 (17.3) 446 (17.6) 428 (16.9) 426 (16.8) 444 (17.5) 444 (17.5) 444 (17.5) H3 mm (in) 144 (5.7) 144 (5.7) 148 (5.8) 148 (5.8) 148 (5.8) 162 (6.4) 162 (6.4) 175 (6.9) S 423 (16.6) 424 (16.7) 424 (16.7) 444 (17.5) 444 (17.5) L 550 (21.6) 550 (21.6) 545 (21.5) 545 (21.5) 547 (21.5) 570 (22.4) 570 (22.4) 548 (21.6) H4 Y mm (in) 586 (23.1) 622 (24.5) X 636 (25.0) U H5 mm (in) 466 (18.3) 445 (17.5) 533 (21.0) 533 (21.0) 533 (21.0) S 621 (24.4) 584 (23.0) 584 (23.0) 622 (24.5) 622 (24.5) L 701 (27.6) 701 (27.6) 648 (25.5) 648 (25.5) 651 (25.6) 691 (27.2) 691 (27.2) 683 (26.9) H6 Y mm (in) 670 (26.4) 719 (28.3) X 754 (29.7) U H7 mm (in) 118 (4.6) 118 (4.65) 278 (10.9) 224 (8.8) 244 (9.6) 127 (5.0) 127 (5.0) 127 (5.0) H8 mm (in) 30 (1.2) 30 (1.2) 29 (1.1) 9 (0.3) 8.7 (0.3) 30 (1.2) 30 (1.2) 30 (1.2) H9 mm (in) 596 (23.5) 596 (23.5) 657 (25.9) 647 (25.5) 661 (26.0) 695 (27.4) 695 (27.4) 695 (27.4) H10 mm (in) 40 (1.6) 40.3 (1.6) 44 (1.7) 44 (1.7) 42 (16.5) 45 (1.8) 45 (1.8) 45 (1.8) S L 22 (0.9) H11 Y mm (in) X U W1 mm (in) 166 (6.5) 166 (6.54) 154 (6.1) 154 (6.1) 190 (7.5) 190 (7.5) 190 (7.5) W2 mm (in) 233 (9.2) 208 (8.2) 152 (6.0) 294 (11.6) 294 (11.6) W3 mm (in) 148 (5.8) 148 (5.83) 152 (6.0) 173 (6.8) 173 (6.8) 173 (6.8) W4 mm (in) 192 (7.6) 192 (7.56) 179 (7.0) 205 (8.1) 205 (8.1) 205 (8.1) W5 mm (in) 302 (11.9) 302 (11.89) 310 (12.2) 310 (12.2) 310 (12.2) 360 (14.2) 360 (14.2) 360 (14.2) W6 mm (in) 472 (18.6) 217 (8.54) 522 (20.6) 602 (23.7) 602 (23.7) 602 (23.7) A1 degree A2 degree A3 degree 4 T1 mm (in) 1-24

33 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (2-STROKE) Symbol Global model (US, CA model) E/40XMH E40XWH E/40XW E/40XWT 40VMHO 50HMHO 40VEO 40VETO 50HET 50HETO 40VMHD 40VWHDO 40VWHTO 50HMHD 50HWHD 50HWHTO E48CMH E55CMH L1 mm (in) 533 (21.8) 553 (21.8) 533 (21.8) 490 (19.3) 490 (19.3) 528 (20.8) 528 (20.8) 487 (19.2) L2 mm (in) 118 (4.6) 118 (4.6) 118 (4.6) 257 (10.1) 178 (7.0) 142 (5.6) 221 (8.7) 298 (11.7) L3 mm (in) 523 (20.6) 789 (31.1) 753 (29.6) 680 (26.8) L4 mm (in) 522 (20.6) 522 (20.6) 522 (20.6) 493 (19.4) 493 (19.4) 529 (20.8) 529 (20.8) 487 (19.2) S 65 (2.6) 65 (2.6) 54 (2.1) L 91 (3.6) 91 (3.6) 91 (3.6) 77 (3.0) 77 (3.0) 71 (2.8) L5 Y mm (in) X 91 (3.6) U S 826 (32.5) 826 (32.5) 798 (31.4) 798 (31.4) 827 (32.6) L 940 (37.0) 940 (37.0) 935 (36.8) 910 (35.8) 910 (35.8) 937 (36.9) 937 (36.9) 932 (36.7) L6 Y mm (in) X 1043 (41.1) 935 (36.8) U L7 mm (in) 397 (15.6) 397 (15.6) 391 (15.4) 433 (17.0) 401 (15.8) 387 (15.2) 418 (16.5) 437 (17.2) L8 mm (in) 294 (11.6) 273 (10.7) 179 (7.0) 153 (6.0) 246 (9.7) 280 (11.0) S 3 (0.1) 3 (0.1) L 8 (0.3) 8 (0.3) 8 (0.3) 10 (0.4) 10 (0.4) L9 Y mm (in) X 16 (0.6) 8 (0.3) U L10 mm (in) 65 (2.6) 65 (2.6) 65 (2.6) 72 (2.8) 72 (2.8) 63 (2.5) 63 (2.5) 77 (3.0) S 767 (30.2) 767 (30.2) 751 (29.6) 751 (29.6) 809 (31.9) L 893 (35.2) 893 (35.2) 893 (35.2) 878 (34.6) 878 (34.6) 880 (34.6) 880 (34.6) 931 (36.7) H1 Y mm (in) X 1007 (39.6) 893 (35.2) U H2 mm (in) 471 (18.5) 471 (18.5) 471 (18.5) 472 (18.6) 441 (17.4) 439 (17.3) 470 (18.5) 449 (17.7) H3 mm (in) 175 (6.9) 175 (6.9) 175 (6.9) 175 (6.9) 175 (6.9) 175 (6.9) 175 (6.9) 191 (7.5) S 424 (16.7) 424 (16.7) 408 (16.1) 408 (16.1) 451 (17.8) L 550 (21.7) 550 (21.7) 550 (21.7) 535 (21.1) 535 (21.1) 537 (21.1) 537 (21.1) 572 (22.5) H4 Y mm (in) X 664 (26.1) 550 (21.7) U H5 mm (in) 532 (20.9) 731 (28.8) 728 (28.7) 568 (22.4) S 626 (24.6) 626 (24.6) 579 (22.8) 579 (22.8) 591 (23.3) L 697 (27.4) 697 (27.4) 637 (25.1) 646 (25.4) 646 (25.4) 709 (27.9) 709 (27.9) 652 (25.7) H6 Y mm (in) X 761 (30.0) 637 (25.1) U H7 mm (in) 159 (6.3) 159 (6.3) 176 (6.9) 201 (7.9) 217 (8.5) 222 (8.7) 204 (8.0) 171 (6.7) H8 mm (in) 38 (1.5) 55 (2.2) 17 (0.7) 0 (0.0) 43 (1.7) 93 (3.7) H9 mm (in) 702 (27.6) 702 (27.6) 706 (27.8) 683 (26.9) 671 (26.4) 688 (27.1) 696 (27.4) 684 (26.9) H10 mm (in) 43 (1.7) 43 (1.7) 43 (1.7) 44 (1.7) 44 (1.7) 44 (1.7) 44 (1.7) 42 (1.7) S 25 (1.0) 25 (1.0) 20 (0.8) 22 (0.9) L 24 (0.9) 24 (0.9) 24 (0.9) 19 (0.7) 19 (0.7) 21 (0.8) H11 Y mm (in) X 24 (0.9) 24 (0.9) U W1 mm (in) 182 (7.2) 182 (7.2) 182 (7.2) 180 (7.1) 180 (7.1) 180 (7.1) W2 mm (in) (8.7) 124 (4.9) 124 (4.9) 159 (6.3) W3 mm (in) 182 (7.2) 182 (7.2) 182 (7.2) 175 (6.9) 175 (6.9) 175 (6.9) 175 (6.9) 165 (6.5) W4 mm (in) 180 (7.1) 180 (7.1) 180 (7.1) W5 mm (in) 369 (14.5) 369 (14.5) 369 (14.5) 340 (13.4) 340 (13.4) 340 (13.4) 340 (13.4) 268 (10.6) W6 mm (in) 592 (23.3) 641 (25.2) 641 (25.2) 507 (20.0) A1 degree A2 degree A3 degree T1 mm (in) 1-25

34 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (2-STROKE) Global model (US, CA model) 55ED S-transom 55ED L-transom 55ET 55DEHD E60HMHD E60HWHD E60HWD 60FEDO S-transom 60FEDO L-transom Symbol L1 mm (in) 531 (20.9) 516 (20.3) 516 (20.3) 545 (21.5) 532 (20.9) 532 (20.9) 547 (21.5) 532 (20.9) L2 mm (in) 159 (6.3) 174 (6.9) 174 (6.9) 180 (7.1) 269 (10.6) 269 (10.6) 151 (5.9) 166 (6.5) L3 mm (in) 790 (31.1) 651 (25.6) 651 (25.6) L4 mm (in) 531 (20.9) 516 (20.3) 516 (20.3) 547 (21.5) 546 (21.5) 546 (21.5) 562 (22.1) 547 (21.5) S 87 (3.4) 97 (3.8) 113 (4.4) L 90 (3.5) 90 (3.5) 88 (3.5) 99 (3.9) 99 (3.9) 91 (3.6) L5 Y mm (in) X U S 818 (32.2) 913 (35.9) 868 (34.2) L 919 (36.2) 919 (36.2) 968 (38.1) 1020 (40.2) 1020 (40.2) 968 (38.1) L6 Y mm (in) X U L7 mm (in) 392 (15.4) 400 (15.7) 400 (15.7) 457 (18.0) 457 (18.0) 403 (15.9) 411 (16.2) L8 mm (in) 154 (6.1) 164 (6.5) 164 (6.5) 164 (6.5) 256 (10.1) 256 (10.1) 206 (8.1) 214 (8.4) S -6 (-0.2) L 14 (0.6) 4 (0.16) L9 Y mm (in) X U L10 mm (in) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) S 758 (29.8) 831 (32.7) 780 (30.7) L 879 (34.6) 879 (34.6) 901 (35.5) 954 (37.6) 954 (37.6) 901 (35.5) H1 Y mm (in) X U H2 mm (in) 424 (16.7) 424 (16.7) 424 (16.7) 520 (20.5) 528 (20.8) 528 (20.8) 472 (18.6) 472 (18.6) H3 mm (in) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) S 399 (15.7) 450 (17.7) 400 (15.7) L 520 (20.5) 520 (20.5) 520 (20.5) 538 (21.2) 538 (21.2) 520 (20.5) H4 Y mm (in) X U H5 mm (in) 753 (29.6) 753 (29.6) S 636 (25.0) 670 (26.4) 645 (25.4) L 689 (27.1) 689 (27.1) 698 (27.5) 722 (28.4) 722 (28.4) 696 (27.4) H6 Y mm (in) X U H7 mm (in) 158 (6.2) 147 (5.8) 147 (5.8) 216 (8.5) 216 (8.5) 262 (10.3) 249 (9.8) H8 mm (in) 12 (0.5) 25 (1.0) 25 (1.0) 23 (0.9) 81 (3.2) 81 (3.2) - 24 (-0.9) -11 (-0.4) H9 mm (in) 695 (27.4) 682 (26.9) 682 (26.9) 743 (29.3) 722 (28.4) 722 (28.4) 719 (28.3) 706 (27.8) H10 mm (in) 47 (1.9) 47 (1.9) 47 (1.9) 47 (1.9) 46 (1.8) 46 (1.8) 47 (1.9) 47 (1.9) S 24 (0.9) 24 (0.9) 24 (0.9) 27 (1.1) L 27 (1.1) 27 (1.1) H11 Y mm (in) X U W1 mm (in) 166 (6.5) 166 (6.5) 166 (6.5) 211 (8.3) 182 (7.2) 182 (7.2) W2 mm (in) 159 (6.3) W3 mm (in) 166 (6.5) 187 (7.4) 182 (7.2) 182 (7.2) W4 mm (in) W5 mm (in) 271 (10.7) 271 (10.7) 271 (10.7) 331 (13.0) 322 (12.7) 322 (12.7) 321 (12.6) 321 (12.6) W6 mm (in) 553 (21.8) A1 degree A2 degree A3 degree T1 mm (in) 1-26

35 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (2-STROKE) Symbol Global model (US, CA model) 60FETO 70ETO S-transom 60FET 60FETO 70ETO L-transom 55DEHD 75AEHD 85AEHD 75AED 85AED 75AET 85AET E75MHD 75CETO 90AETO E115AMH E115AWH L1 mm (in) 547 (21.5) 532 (20.9) 545 (21.5) 545 (21.5) 545 (21.5) 545 (21.5) 545 (21.5) 539 (21.2) L2 mm (in) 151 (5.9) 166 (6.5) 180 (7.1) 180 (7.1) 180 (7.1) 270 (10.6) 180 (7.1) 325 (12.8) L3 mm (in) 790 (31.1) 652 (25.7) 845 (33.3) L4 mm (in) 562 (22.1) 547 (21.5) 547 (21.5) 547 (21.5) 547 (21.5) 547 (21.5) 547 (21.5) 616 (24.3) S 113 (4.4) L 91 (3.6) 88 (3.5) 88 (3.5) 88 (3.5) 81 (3.2) 88 (3.5) 80 (3.1) L5 Y mm (in) 85 (3.3) 80 (3.1) 75 (3.0) X 85 (3.3) 80 (3.1) 80 (3.1) 70 (2.8) 80 (3.1) 85 (3.3) U S 868 (34.2) L 968 (38.1) 968 (38.1) 968 (38.1) 968 (38.1) 966 (38.0) 968 (38.1) 1005 (39.6) L6 Y mm (in) 1015 (40.0) 1011 (39.8) 1055 (41.5) X 1080 (42.5) 1080 (42.5) 1080 (42.5) 1078 (42.4) 1080 (42.5) 1120 (44.1) U L7 mm (in) 403 (15.9) 411 (16.2) 459 (18.1) 459 (18.1) 459 (18.1) 542 (21.3) 457 (18.0) 570 (22.4) L8 mm (in) 206 (8.1) 214 (8.4) 164 (6.5) 164 (6.5) 164 (6.5) 256 (10.1) 164 (6.5) 270 (10.6) S 0.0 (0.0) L 14 (0.6) 14 (0.6) 14 (0.6) L9 Y mm (in) X 23 (0.9) 31 (1.2) U L10 mm (in) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) 67 (2.6) 68 (2.7) 67 (2.6) 64 (2.5) S 780 (30.7) L 901 (35.5) 901 (35.5) 901 (35.5) 901 (35.5) 902 (35.5) 901 (35.5) 929 (36.6) H1 Y mm (in) 952 (37.5) 953 (37.5) 982 (38.7) X 1028 (40.5) 1028 (40.5) 1028 (40.5) 1028 (40.5) 1028 (40.5) 1056 (41.6) U H2 mm (in) 472 (18.6) 472 (18.6) 520 (20.5) 520 (20.5) 520 (20.5) 590 (23.2) 512 (20.2) 631 (24.8) H3 mm (in) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 191 (7.5) 190 (7.5) S 400 (15.7) L 520 (20.5) 520 (20.5) 520 (20.5) 520 (20.5) 521 (20.5) 520 (20.5) 515 (20.3) H4 Y mm (in) 571 (22.5) 572 (22.5) 568 (22.4) X 647 (25.5) 647 (25.5) 647 (25.5) 648 (25.5) 647 (25.5) 642 (25.3) U H5 mm (in) 555 (21.9) 695 (27.4) S 645 (25.4) L 696 (27.4) 698 (27.5) 698 (27.5) 698 (27.5) 698(27.5) 698 (27.5) 735 (28.9) H6 Y mm (in) 729 (28.7) 725 (28.5) 765 (30.1) X 764 (30.1) 764 (30.1) 764 (30.1) 766 (30.2) 764 (30.1) 810 (31.9) U H7 mm (in) 262 (10.3) 249 (9.8) 199 (7.8) 199 (7.8) 199 (7.8) 253 (10.0) 226 (8.9) 150 (5.9) H8 mm (in) -24 (-0.9) -11 (-0.4) 23 (0.9) 23 (0.9) 23 (0.9) 84 (3.3) 23 (0.9) 155 (6.1) H9 mm (in) 719 (28.3) 706 (27.8) 743 (29.3) 743 (29.3) 743 (29.3) 778 (30.6) 730 (28.7) 780 (30.7) H10 mm (in) 47 (1.9) 47 (1.9) 47 (1.9) 47 (1.9) 47 (1.9) 46 (1.8) 47 (1.9) 45 (1.8) S 0 (0.0) L 28 (1.1) 27 (1.1) 27 (1.1) H11 Y mm (in) X 27 (1.1) 27 (1.1) U W1 mm (in) 182 (7.2) 182 (7.2) 211 (8.3) 187 (7.4) 187 (7.4) 187 (7.4) 300 (11.8) W2 mm (in) 159 (6.3) 210 (8.3) W3 mm (in) 187 (7.4) 187 (7.4) 187 (7.4) 187 (7.4) 187 (7.4) 300 (11.8) W4 mm (in) 300 (11.8) W5 mm (in) 321 (12.6) 321 (12.6) 331 (13.0) 331 (13.0) 331 (13.0) 331 (13.0) 331 (13.0) 424 (16.7) W6 mm (in) 506 (19.9) 705 (27.8) A1 degree A2 degree A3 degree T1 mm (in) 600 (23.6) 600 (23.6) 600 (23.6) 600 (23.6) 600 (23.6) 660 (26.0) 1-27

36 OUTOARD MOTOR DIMENSIONS OVERALL DIMENSIONS (2-STROKE) Global model (US, CA model) E115AE 115E E115AET 115ET 140ET 115CETO 130ETO L/150AET L/200AET Z150QETO (VZ150TR) L/250GETO Symbol L1 mm (in) 539 (21.2) 539 (21.2) 542 (21.3) 554 (21.8) 543 (21.4) 613 (24.1) 566 (22.3) L2 mm (in) 213 (8.4) 213 (8.4) 188 (7.4) 176 (6.9) 188 (7.4) 180 (7.1) 181 (7.1) L3 mm (in) L4 mm (in) 616 (24.3) 616 (24.3) 616 (24.3) 632 (24.9) 634 (25.0) 646 (25.4) 673 (26.5) S L 80 (3.1) 80 (3.1) 70 (2.8) 70 (2.8) 49 (1.9) 53 (2.1) L5 Y mm (in) X 85 (3.3) 85 (3.3) 61 (2.4) 61 (2.4) 62 (2.4) 69 (2.7) U 89 (3.5) S L 1005 (39.6) 1005 (39.6) 1007 (39.6) 1007 (39.6) 1030 (40.6) 1034 (40.7) L6 Y mm (in) X 1120 (44.1) 1120 (44.1) 1124 (44.3) 1124 (44.3) 1144 (45.0) 1155 (45.5) U 1271 (50.0) L7 mm (in) 482 (19.0) 482 (19.0) 468 (18.4) 463 (18.2) 569 (22.4) 574 (22.6) 631 (24.8) L8 mm (in) 214 (8.4) 215 (8.5) 173 (6.8) 159 (6.3) 173 (6.8) 168 (6.6) 185 (7.3) S L 12 (0.5) 44 (1.7) 31 (1.2) 54 (2.1) 42 (1.7) L9 Y mm (in) X 12 (0.5) 53 (2.1) 40 (1.6) 62 (2.4) 52 (2.0) U 58 (2.3) L10 mm (in) 64 (2.5) 64 (2.5) 74 (2.9) 74 (2.9) 74 (2.9) 74 (2.9) 73.8 (2.9) S L 929 (36.6) 929 (36.6) 928 (36.5) 928 (36.5) 946 (37.2) 947 (37.3) H1 Y mm (in) X 1056 (41.6) 1056 (41.6) 1054 (41.5) 1054 (41.5) 1072 (42.2) 1077 (42.4) U 1203 (47.4) H2 mm (in) 508 (20.0) 508 (20.0) 544 (21.4) 544 (21.4) 631 (24.8) 746 (27.9) 710 (28.0) H3 mm (in) 190 (7.5) 190 (7.5) 191 (7.5) 191 (7.5) 210 (8.3) 211 (8.3) 216 (8.5) S L 515 (20.3) 515 (20.3) 515 (20.3) 515 (20.3) 516 (20.3) 516 (20.3) H4 Y mm (in) X 642 (25.3) 642 (25.3) 642 (25.3) 642 (25.3) 642 (25.3) 642 (25.3) U 768 (30.2) H5 mm (in) S L 735 (28.9) 735 (28.9) 764 (30.1) 764 (30.1) 762 (30.0) 774 (30.5) H6 Y mm (in) X 810 (31.9) 810 (31.9) 839 (33.0) 839 (33.0) 837 (33.0) 846 (33.3) U 923 (36.3) H7 mm (in) 150 (5.9) 150 (5.9) 180 (7.1) 191 (7.5) 205 (8.1) 308 (12.1) 242 (9.5) H8 mm (in) 53 (2.1) 55 (2.2) 26 (1.0) 15 (0.6) 26 (1.0) 14 (0.6) 21 (0.8) H9 mm (in) 730 (28.7) 730 (28.7) 730 (28.7) 741 (29.2) 788 (31.0) 945 (37.2) 818 (32.2) H10 mm (in) 45 (1.8) 45 (1.8) 45 (1.8) 46 (1.8) 45.4 (1.8) 44 (1.7) 45.4 (1.8) S L 30 (1.2) 30 (1.2) 31 (1.2) 32 (1.3) H11 Y mm (in) X 30 (1.2) 30 (1.2) 31 (1.2) 25 (1.0) U 25 (1.0) W1 mm (in) 297 (11.7) 300 (11.8) 291 (11.5) 291 (11.5) 301 (11.9) 277 (10.9) 281 (11.1) W2 mm (in) W3 mm (in) 297 (11.7) 300 (11.8) 291 (11.5) 291 (11.5) W4 mm (in) W5 mm (in) 422 (16.6) 424 (16.7) 409 (16.1) 409 (16.1) 426 (16.8) 396 (15.6) 420 (16.5) W6 mm (in) A1 degree A2 degree A3 degree T1 mm (in) 660 (26.0) 660 (26.0) 660 (26.0) 660 (26.0) 660 (26.0) 660 (26.0) 1-28

37 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSION ITEMS Symbol C1 C2 C3 D1 D2 D3 D4 AN1 AN2 Definition and Description Horizontal dimension from centerline of motor body to lower bracket mounting hole (slot) Vertical dimension from transom top to lower bracket mounting hole (slot) Horizontal dimension from centerline of motor body to the center of upper bracket mounting hole Vertical dimension from transom top to the center of upper bracket mounting hole Horizontal dimension from centerline of motor body to the point of largest width on the bracket Vertical dimension from transom top to lowest point on the bracket Horizontal dimension from centerline of motor body to the center of lower extra bracket mounting hole Vertical dimension from transom top to the center of extra hole at the lower part of bracket Dimensions between the upper bracket mounting bolts (when holes are at even intervals) Dimensions between the upper bracket mounting bolts (when holes are not at even intervals) Horizontal dimensions from centerline of motor body to the clamping bolt center Vertical dimensions from transom top to the clamping bolt center Mount flange thickness of clamp bracket Allowable transom board thickness when clamping screw is driven-in to the least extent Allowable transom board thickness when clamping screw is driven-in to the full extent Maximum allowable transom plate thickness for mounting the motor Diameter of bracket (main) lower mounting hole, or screw Diameter of bracket (main) mounting hole, or screw (lower mounting hole diameter, or, for slot, center-to-center distance of both end circles) Diameter of bracket mounting (sub) hole Diameter of central bracket mounting extra hole or the screw size Vertical dimension from bottom of clamp bracket to the bottom end of anode Horizontal dimension from centerline of motor (anode) to the point of largest width of anode 1-29

38 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F2A F2.5A US/CA model F2.5A Manual tilt 5 11 C/L C1 C2 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 8 C1 22 (0.9) D1 2 9 C2 58 (2.3) D C3 D (2.2) D (2.7) (1.6) (5.7)

39 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 4AC 5C 5CS F4 F5A F6C US/CA model F4A F6A Manual tilt 5 11 C/L C1 C2 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 8 C1 22 (0.9) D1 2 9 C2 58 (2.3) D C3 D (2.2) D (3.3) (1.9) (5.4)

40 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 6C 8C US/CA model Manual tilt 11 C/L C1 C2 5 5 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 8 C1 22 (0.9) D1 2 9 C2 55 (2.2) D C3 D (2.2) D (3.0) (2.0) (6.5)

41 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F8C FT8D US/CA model F8A Manual tilt 5 C/L C1 D1 C2 D2 3 3 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (2.8) 8 C1 32 (1.3) D1 8.3 (0.3) (7.1) 9 18 (0.7) C2 65 (2.6) D2 8.3 (0.3) (3.8) 10 C3 D (3.7) 11 D (4.2) (1.9) (7.4)

42 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 9.9F 15F US/CA model Manual tilt C/L D1 D2 C1 C2 1 1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (3.6) 8 C1 30 (1.2) D1 8.3 (0.3) (4.1) (2.1) C2 56 (2.2) D2 8.3 (0.3) (3.6) 10 C3 D (1.9) (2.8) D (4.0) (2.7) (6.9)

43 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model E9.9D E15D EK9.9D EK15D EK9.9J EK15P US/CA model Manual tilt 5 C/L C1 D1 9 6 C2 C3 1 1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (3.6) 8 C1 30 (1.2) D1 8.3 (0.32) 2 79 (3.1) (4.2) C2 60 (2.4) D C3 D (2.6) D (4.2) (2.0) (6.2)

44 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F9.9H F15C F20 F20C F9.9J FT9.9L US/CA model F15A F20A F9.9 T9.9 Manual tilt 11 C/L D1 C2 C Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 8 C1 32 (1.3) D1 8.3 (0.33) (0.71) C2 67 (2.6) D (3.8) 10 C3 D (3.0) (2.8) D (4.3) (1.9) (7.4)

45 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model FT8D F15C F20 FT9.9L US/CA model F15A F20A T9.9 Power tilt 5 C/L C1 D1 C2 D D1 1 1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (3.8) 8 C1 38 (1.5) D1 8.3 (0.3) (10.8) 9 18 (0.7) C2 67 (2.6) D2 10 (0.4) (3.8) 10 C3 D (3.7) (2.9) D (4.4) (2.7) (12.8)

46 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model E/25 25X E/30H EK25 EK25C US/CA model Manual tilt 11 C/L C1 C2 D2 6 D1 D Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 89 (3.5) 8 C1 35 (1.4) D1 8.5 (0.33) (5.5) 9 C2 65 (2.6) D2 15 (0.59) (4.4) 10 C3 D (3.8) (3.3) D (4.8) (2.0) (6.9)

47 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 20D 25N US/CA model Manual tilt 5 C/L D1 6 C1 C2 3 3 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 8 C1 25 (1.0) D1 8.3 (0.32) (3.8) 9 C2 65 (2.6) D (4.5) 10 C3 D (3.4) D (4.8) (3.3) (6.9)

48 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model E/40X F25D US/CA model F25A Manual tilt 5 C/L D1 C2 C1 3 3 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 8 C1 37 (1.5) D (0.41) (2.0) C2 68 (2.7) D (5.5) 10 C3 D (1.3) (3.8) D (5.9) (2.2) (8.6)

49 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model E40G E40J EK40G EK40J US/CA model Manual tilt 5 C/L D2 D D1 C2 C1 3 3 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 8 C1 33 (1.3) D (0.41) (8.3) 9 50 (2.0) C2 60 (2.3) D2 27 (1.1) (4.9) 10 C3 D (1.3) (3.7) D (5.3) (2.2) (9.8)

50 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 30D E/40X F25D FT25F F30 F40F F20D US/CA model F25A/ T25A F30A F40A PTT & Hydro-tilt 5 C/L 5 4 C3 D1 3 D D1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (5.0) 8 C1 D1 13 (0.5) (10.0) (0.7) C2 D (2.2) (6.4) 10 C3 69 (2.7) D (2.0) 11 D (7.1) (13.3)

51 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F40H F50H FT50J F60F FT60G F70A F40G US/CA model F50 T50 F60 T60 F70A PTT & Hydro-tilt 5 C/L 5 4 C3 D1 3 D D1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (5.0) 8 C1 D1 13 (0.5) (10.0) (0.7) C2 D (2.2) (6.4) 10 C3 69 (2.7) D (2.0) 11 D (7.1) (13.8)

52 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 40V 50H E60H F50D FT50C US/CA model PTT & Hydro-tilt C/L D D1 C3 D3 D Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (5.0) (8.0) C1 D1 13 (0.51) (10.0) (0.73) C2 D (2.4) (6.4) 10 C3 69 (2.7) D3 13 (0.51) (2.0) 11 D (7.1) (14.0) (5.4) 1-44

53 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 30D 40V 50H US/CA model Manual tilt 5 3 C/L D D1 C1 C2 D1 1 1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (2.5) 8 C1 30 (1.2) D (0.41) (8.2) 9 25 (0.98) C2 66 (2.6) D2 26 (1.0) (4.8) 10 C3 D (1.3) (3.6) D (5.2) (2.2) (9.6)

54 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model E48C E55C US/CA model Manual tilt 11 C/L C3 D3 D1 D2 AN AN2 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) 1 96 (3.8) 8 95 (3.7) C1 AN1 14 (0.55) (9.1) 9 C2 AN2 12 (0.47) (4.7) 10 C3 73 (2.9) (3.8) D1 12 (0.47) (5.1) (2.2) D2 8 (0.31) (10.0) D (0.41) 7 D4 1-46

55 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 55 60F E60H US/CA model PTT & Hydro-tilt for S-transom 5 3 C/L D1 C3 7 7 D3 AN2 AN2 D2 AN1 D1 1 1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) (8.0) C1 D1 13 (0.51) (10.0) (0.73) C2 D (2.2) (6.4) 10 C (2.7) Studbolt hole: M deep (2.0) 11 D (7.1) 12 D (13.0) AN1 19 (0.75) (5.4) AN (4.0) 1-47

56 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model 55 55D 60F 70 75A 75C 85A 90A US/CA model Global model E60H E75 US/CA model PTT & Hydro-tilt for L/X-transom 5 3 C/L 5 3 D C3 D1 D3 AN2 AN2 AN D1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) (8.0) C1 D1 13 (0.51) (10.0) (0.73) C2 D (2.2) (6.4) 10 C (2.7) Studbolt hole: M deep (2.0) 11 D (7.1) 12 D (13.9) AN1 19 (0.75) (5.4) AN (4.0) 1-48

57 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F75 F80 F90 F100D US/CA model F75A F90A PTT 5 3 C/L 5 3 C D D1 AN2 AN2 AN1 1 1 D1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) 8 C1 AN1 19 (0.75) (10.0) (0.73) C2 AN (4.0) (6.4) 10 C3 80 (3.1) (2.0) 11 D1 13 (0.51) (7.1) 12 D (2.2) (14.5) (0.79) D3 7 D4 1-49

58 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model E115A C L/150A 150G Z150Q US/CA model VZ150 Global model L/200A F75C F95A F100 F/FL115A US/CA model F/LF115A Global model F/FL150A F/FL150 F225C US/CA/ANZ model F/LF150A PTT & Hydro tilt 5 C/L D1 C3 13 D2 6 4 AN2 AN2 D1 AN1 1 1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) 8 C1 AN1 52 (2.0) (10.0) (0.73) C2 AN2 102 (4.0) (6.4) 10 C3 82 (3.2) (2.0) 11 D1 13 (0.51) (7.1) 12 D (2.2) (14.4) (0.94) D3 7 D4 1-50

59 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F/FL115 US/CA/ANZ model F/LF115 PTT 5 C/L C3 6 D1 AN1 D2 D1 D1 AN2 1 AN Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) 8 C1 AN1 17 (0.7) (10.0) (0.73) C2 AN (4.0) (6.4) 10 C3 82 (3.2) (2.0) 11 D1 13 (0.51) (7.1) 12 D (2.2) (14.1) (0.79) D3 7 D4 1-51

60 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F175A F/FL200F F/FL200G US/CA/ANZ model F175A F/LF200 F/LF200CA PTT 5 3 C/L C3 6 D1 D2 2 AN1 AN2 AN2 D Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) 8 C1 AN1 25 (1.0) (10.0) (0.73) C2 AN2 102 (4.0) (6.4) 10 C3 82 (3.2) (2.0) 11 D1 13 (0.51) (7.1) 12 D (2.2) (14.4) (0.94) D3 7 D4 1-52

61 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F150C F165A F200D F225D F250C F225G F250F F275A US/CA/ANZ model VF150A VF200A VF225A VF250A PTT 5 3 C/L C3 6 D1 D2 2 AN1 AN2 AN2 D Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) 8 C1 AN (0.5) (10.0) (0.7) C2 AN (6.4) 10 C3 82 (3.2) (2.0) 11 D1 13 (0.5) (7.1) 12 D (2.2) (14.5) (0.79) D3 7 D4 1-53

62 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model L/250G F/FL200 F/FL200C F/FL225 F/FL250A F/FL250G F/FL225F F/FL250D US/CA/ANZ model F/LF200A F/LF225A F/LF250A F/LF225CA F/LF250CA Global model F/FL300 US/CA/ANZ model F/LF300CA PTT 5 3 C/L D1 2 C3 13 AN2 AN2 AN1 D D1 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) 8 C1 AN1 52 (2.0) (10.0) (0.7) C2 AN2 102 (4.0) (6.4) 10 C3 79 (3.1) (2.0) 11 D1 13 (0.5) (7.1) 12 D (2.2) (16.2) (0.79) D3 7 D4 1-54

63 OUTOARD MOTOR DIMENSIONS CLAMP RACKET DIMENSIONS Global model F/FL350A US/CA/ANZ model F/LF350C PTT 5 3 C/L D1 6 D D1 AN2 1 AN2 1 AN1 13 Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) Symbol mm (in.) (4.9) 8 C1 AN1 19 (0.75) (10.0) (0.73) C2 AN2 102 (4.0) (6.4) 10 C (2.0) 11 D1 13 (0.51) (7.1) 12 D (3.6) (16.0) (0.83) D3 7 D4 1-55

64 MEMO

65 PROPELLERS PROPELLER SPECIFICATIONS PROPELLER TYPES PROPELLER IDENTIFICATION PROPELLER SELECTION PROPELLER APPLICATIONS STANDARD PROPELLER STANDARD PROPELLERS (Shift Dampener System [SDS]) DUAL THRUST PROPELLERS WEEDLESS PROPELLERS RELIANCE SERIES PROPELLERS (STD) RELIANCE SERIES PROPELLERS (Shift Dampener System [SDS]) SALTWATER SERIES PROPELLERS SALTWATER SERIES II PROPELLERS (STD) SALTWATER SERIES II PROPELLERS (Shift Dampener System [SDS]) SALTWATER SERIES HS4 PROPELLERS (STD) SALTWATER SERIES HS4 PROPELLERS (Shift Dampener System [SDS]) SALTWATER SERIES XL PROPELLERS (Shift Dampener System [SDS]) SALTWATER SERIES XL4 PROPELLERS (Shift Dampener System [SDS]) VMAX SERIES PROPELLERS PERFORMANCE SERIES PROPELLERS HIGH PERFORMANCE SERIES PROPELLERS WOT OPERATION RANGE TALE

66 PROPELLER SPECIFICATIONS PROPELLER TYPES Yamaha propellers are specifically designed to match the characteristics of Yamaha outboard motors. There are some types of propellers for the best matching depending on the operating condition. Major types of propellers include: RELIANCE SERIES New polished stainless steel propellers are designed to provide for 150PS and bigger standard type engines. These propellers are generally more aggressive than black standard stainless steel propellers, and will fit the engines under almost all operating conditions. L/H rotation propellers are available for twinengine applications. STANDARD This propeller series is designed for general use to match a wide range of operating conditions. A stainless steel or an aluminum propeller can be selected to suit the preference of the user. A stainless steel, counter rotation propeller is available for twin engine applications. The aluminum, regular rotation propeller with SDS (Shift Dampener System) is now designed to match the K-series fitting boss. SALTWATER SERIES II This new breed of stainless steel props is designed exclusively for offshore fishing boats and features highly polished, larger diameter design. The aggressive rake angle and extra cupping on the blades provide superior midrange fuel efficiency, along with excellent anticavitation performance. Shift Dampener System (SDS) has been adopted to reduce the shock and noise when shifting, and become possible to replace the propeller damper. L/H rotation propellers are available for twinengine applications. 2-2

67 PROPELLER SPECIFICATIONS SALTWATER SERIES XL New polished stainless steel propellers have been designed for big offshore boats to obtain big impulsion power. It features large diameter blade design, especially for F350 engine. Shift Dampener System (SDS) has been adopted to reduce the shock and noise when shifting, and become possible to replace the propeller damper. L/H rotation propellers are available for multiengine applications. SALTWATER SERIES HS4 Polished stainless steel propellers with 4-blade for V6-3.1L, 3.3L and 4.2L engines, except for VMAX series. Compared with the conventional three blades propeller, four blades make larger propeller blade surface area, which can catch much more water and obtain higher thrust performance. As a result, this propeller will obtain better acceleration, and stable operation under rough water. However, generally boat top speed performance is slightly lower than three blades propeller. Shift Dampener System (SDS) has been adopted to reduce the shock and noise when shifting, and it is possible to replace the propeller damper. L/H rotation propellers are available for twin application. 2-3

68 PROPELLER SPECIFICATIONS SALTWATER SERIES XL4 Designed for the V8 F L four stroke only, this stainless steel four blade prop is intended for large offshore boats such as express cruisers or walk arounds that require massive thrust-to-plane and additional propeller grip for maximum operational efficiency. Made of highly polished stainless steel and available with our patent-pending Shift Dampener System (SDS). PERFORMANCE These stainless steel propellers with vents for exhaust gas induction offer the best acceleration and top end performance causing the engine rpm rapidly increasing with a high rake, progressive pitch and more cup. It allows higher transom mounting such as bass boats, yet does not increase steering torque. * Shift Dampener System (SDS): Using a special new design and high-strength components, much of the resulting force of an outboard shifting into forward or reverse gear is absorbed, resulting in far quieter and smoother operation. PROPELLER SPECIFICATIONS HIGH PERFORMANCE With the progressive pitch design and highly cupped blades, these special small hub propellers are designed for high-performance runabout boats. The through-hub exhaust system allows the exhaust gas to outlet the leading edge of each blade for enhanced acceleration. VMAX SERIES These polished stainless steel propellers are designed for a high-speed and light weight special boat with high-power engine for better performance. These specialized propellers are generally more aggressive than the ventilated type propellers. WEEDLESS This is designed for use in shallow water. It eliminates weed buildup around the propeller hub. 2-4

69 PROPELLER SPECIFICATIONS DUAL THRUST This is designed for sailboat or other large displacement boats. This redirects the exhaust gases so that the blades cut through clean water, for higher efficiency. PROPELLER IDENTIFICATION The propeller identification of the size is indicated as follows. Propeller identification = Diameter (inch) X Pitch (inch) Mark Diameter: Diameter of propeller rotating circle. Pitch: Logical advancing distance when propeller rotated one time. Pitch Diameter The location of the propeller identification varies. Refer to the illustration as shown. 3 4 REAR VIEW FRONT VIEW Example: (1) 7-1/4 X 6 - S (2) 21 - ML (Pitch - Mark) (3) 13 X 17 - K2 (4) 19K (Pitch and Mark) (5) 9-1/4 X 9 - J * Calculation formula of the logical boat speed is as below. ^ oat speed (km/h) = propeller pitch (inch) X engine speed (r/min) X X propeller efficiency / gear ratio. ^ Propeller efficiency = Actual advancing distance when propeller rotated one time / Logical advancing distance when propeller rotated one time. 2-5

70 PROPELLER SELECTION Depending on the model, Yamaha outboard motors are fitted with the propellers which are chosen to perform well over a range of applications, but there may be the uses where a propeller with a different pitch would be more appropriate. For a greater operating load, a smaller pitch propeller is more suitable as enables the correct engine speed at WOT (Wide-Open-Throttle) to be maintained. Conversely, a larger pitch propeller is more suitable for a smaller operating load. For details, see the WOT operation range table in this chapter. esides, select the best matched propeller series that meet the purpose of use depending on the classification and/or type of boat PROPELLER APPLICATIONS STANDARD PROPELLER 2 ps Global model 2C US/CA model lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 7 1/4 4 A Plastic 6A Fitted with shear pin 3 7 1/4 4 1/2 A Aluminum Fitted with shear pin 3 7 1/4 5 A Aluminum 6F Fitted with shear pin 3 7 1/4 5 1/2 A Aluminum Fitted with shear pin 2 3 ps Global model F2A F2.5A 3A US/CA model F2.5A lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 7 1/4 5 S Aluminum 6L /4 5 1/2 S Aluminum 6L /4 6 S Aluminum 6L /4 7 1/4 S Aluminum 6L /4 8 1/4 S Aluminum 6L * Use the thrust washer (68D-G ) for 4-stroke mode, and (6L ) for 2-stroke model. 4 6 ps Global model 4AC 5C 5CS F4 F5A 5CM F6C US/CA model F4A F6A lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 7 1/4 6 1/2 A Aluminum 6E /2 7 A Aluminum 6E /2 8 A Aluminum 6E /4 8 1/4 A Aluminum 6E /2 9 A Aluminum 6E

71 2014 PROPELLER APPLICATIONS STANDARD PROPELLER 8 ps Global model E8D EK8D US/CA model lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 7 1/4 5 C Aluminum Fitted with shear pin /4 C Aluminum Fitted with shear pin /2 C Aluminum Fitted with shear pin C Aluminum Fitted with shear pin /2 C Aluminum Fitted with shear pin C Aluminum Fitted with shear pin 3 9 1/4 9 1/4 C Aluminum Fitted with shear pin ps Global model 6C 8C F8C F9.9J US/CA model F8A F9.9 lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 8 1/2 6 1/2 N Aluminum 6G /2 7 1/2 N Aluminum 6G /2 8 N Aluminum 6G /2 8 1/2 N Aluminum 6G /2 9 1/4 N Aluminum 6G ps Global model 9.9F 15F E9.9D E15D EK9.9J EK15P EK9.9D EK15D US/CA model Global model F9.9H F15C US/CA model F15A lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 9 1/2 6 1/2 J Aluminum /4 8 J Aluminum 63V /4 9 3/4 J Aluminum /4 10 J Aluminum 63V /4 10 1/2 J Aluminum /4 11 J Aluminum 63V /4 12 J Aluminum * Use the thrust washer ( ) for kerosene model, avoiding propeller damper damage ps Global model F9.9H F15C F20 F20C US/CA model F15A F20A lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 9 1/4 9 J1 Aluminum 63V /4 10 J1 Aluminum 63V /4 11 J1 Aluminum 63V /4 12 J1 Aluminum 63V

72 2014 PROPELLER APPLICATIONS STANDARD PROPELLER ps Global model 20D 25N E/25 25X E/30H EK25/C 30D F25D US/CA model F25A/ Global model F20D US/CA model lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 9 7/8 8 F Aluminum /8 9 F Aluminum /8 10 F Aluminum 62C /8 10 1/2 F Aluminum /8 11 1/4 F Aluminum /8 12 F Aluminum /8 13 F Aluminum /8 14 F Aluminum /8 12 F S-Steel /8 13 F S-Steel FT/T25 & ps Global model 40V 50H E40J EK40J E/40X E48C E55C 55 US/CA model Global model FT25F F30 F40F F50D F40H F50H F60H 40X US/CA model T25A F30A F40A F50 F60 lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 8 G Aluminum 63D /4 9 G Aluminum /4 10 G Aluminum /8 11 G Aluminum 69W /8 12 G Aluminum 6H /8 12 G Aluminum /8 12 G Aluminum 69W /8 13 G Aluminum 6H /8 13 G Aluminum 69W /4 14 G Aluminum 6H /4 14 G Aluminum 69W /4 14 G Aluminum G Aluminum 6H G Aluminum 69W /4 16 G Aluminum /4 17 G Aluminum G S-Steel /4 12 G S-Steel /2 13 G S-Steel /4 14 G S-Steel /4 14 G S-Steel /4 15 G S-Steel /4 16 G S-Steel

73 2014 PROPELLER APPLICATIONS STANDARD PROPELLER 40 ps Global model E40G EK40G US/CA model lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 7 1/2 H Aluminum Fitted with drive pin /4 8 3/4 H Aluminum Fitted with drive pin /4 10 H Aluminum Fitted with drive pin /2 11 H Aluminum Fitted with drive pin /2 12 H Aluminum Fitted with drive pin /2 13 H Aluminum Fitted with drive pin /2 13 1/2 H Aluminum Fitted with drive pin ps Global model 60F 70 E60H 55D 75A E75 US/CA model Global model 85A 75C 90A 115C 130 E115A US/CA model Global model F40G FT50C FT50J FT60G F70A F75 F75C F80 US/CA model T50 T60 F70A F75A Global model F90 F95A F100 F100D F115A US/CA model F90A F115A Global model F115 US/CA/ANZ model F115 lade Dia. (in) Pitch (in) Mark Material Part number Remarks K Aluminum 6E /8 13 K Aluminum 6E /8 14 K Aluminum 6E /2 15 K Aluminum 6E /4 17 K Aluminum 6E K Aluminum 6E /8 21 K Aluminum 6E K Aluminum 6E K Aluminum 6E /2 14 K S-Steel /2 16 K S-Steel K S-Steel K S-Steel K S-Steel K S-Steel K S-Steel L115 ps Global model FL115A US/CA model LF115A Global model FL115 US/CA/ANZ model LF115 lade Dia. (in) Pitch (in) Mark Material Part number Remarks KL S-Steel 6L KL S-Steel 6L KL S-Steel 6L

74 2014 PROPELLER APPLICATIONS STANDARD PROPELLER ps Global model 150A 200A US/CA model Global model F150A F150 F200 F200C F200F F200G US/CA/ANZ model F150A F200A F200 F200CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 M Aluminum 6G /8 16 M Aluminum 6G /2 17 M Aluminum 6G M Aluminum 6G /4 21 M Aluminum 6G /2 23 M Aluminum 6G L150 L200 ps Global model L150A L200A US/CA model Global model FL150A FL150 FL200 FL200C FL200F FL200G US/CA/ANZ model LF150A LF200A LF200 LF200CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks /2 17 ML Aluminum 6K ML Aluminum 6K ps Global model 150A 200A 250G US/CA model Global model F150A F150 F200 F200C F200F F200G F225 F225C US/CA/ANZ model F150A F200A F200 F200CA F225A Global model F250A F250G US/CA/ANZ model F250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 13 M S-Steel 6G /4 15 M S-Steel 6G /4 17 M2 S-Steel 6G /4 19 M2 S-Steel 6G /4 21 M S-Steel 6G /8 23 M S-Steel 6G /8 25 M S-Steel 6G

75 2014 PROPELLER APPLICATIONS STANDARD PROPELLER L150 L250 ps Global model L150A L200A L250G US/CA model Global model FL150A FL150 FL200 FL200C FL200F FL200G FL225 FL250A US/CA/ANZ model LF150A LF200A LF200F LF200CA LF225A LF250A Global model FL250G US/CA/ANZ model lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 ML S-Steel 6K /4 17 ML1 S-Steel 6K /4 19 ML1 S-Steel 6K /4 21 ML S-Steel 6K /8 23 ML S-Steel 6K ps Global model 250G US/CA model Global model F200 F200C F225 F225C F250A F250G US/CA/ANZ model F200A F225A F250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks T S-Steel 61A /2 19 T S-Steel 61A /2 21 T S-Steel 61A L200 L250 ps Global model L250G US/CA model Global model FL200 FL200C FL225 FL250A FL250G US/CA/ANZ model LF200A LF225A LF250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks TL S-Steel /2 19 TL S-Steel /2 21 TL S-Steel

76 2014 PROPELLER APPLICATIONS STANDARD PROPELLERS (Shift Dampener System [SDS]) ps Global model 55D 60F E60H 70 75A E75 75C 85A US/CA model Global model 90A E115A C F40G FT50C US/CA model Global model FT50J FT60G F70A F75 F75C F80 F90 F95A US/CA model T50 T60 T70A F75A F90A Global model F100 F100D F115A US/CA model F115A Global model F115 US/CA/ANZ model F115 lade Dia. (in) Pitch (in) Mark Material Part number Remarks /2 9 K Aluminum 6EK /2 10 1/2 K Aluminum 6EK /2 12 K Aluminum 6EK /2 14 K Aluminum 6EK /4 16 K Aluminum 6EK

77 2014 PROPELLER APPLICATIONS DUAL THRUST PROPELLERS ps Global model 6C 8C F8C F9.9J US/CA model F8A F9.9 lade Dia. (in) Pitch (in) Mark Material Part number Remarks N Aluminum 6G1-W N Aluminum 6G1-W ps Global model FT8D FT9.9L US/CA model T9.9 lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 5 3/4 R Aluminum 69G /4 7 R Aluminum 69G /4 9 1/4 R Aluminum 6G ps Global model 9.9F 15F E9.9D E15D EK9.9J EK15P EK9.9D EK15D US/CA model Global model F9.9H F15C US/CA model F15A lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 9 3/4 6 1/2 J Aluminum 683-W /4 8 J Aluminum 683-W * Use the thrust washer ( ) for kerosene model, avoiding propeller damper damage ps Global model 30D F25D E25 30H E30H US/CA model F25A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /8 8 1/4 F Aluminum 6J8-W For PT/PTT/Hydro model. 25 ps Global model FT25F US/CA model T25A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 9 G Aluminum 68U ps Global model FT50C FT50J FT60G F70A US/CA model T50 T60 F70A lade Dia. (in) Pitch (in) Mark Material Part number Remarks K Aluminum 68S

78 2014 PROPELLER APPLICATIONS WEEDLESS PROPELLERS 4 6 ps Global model 4AC 5C/S F4 F5A F6C US/CA model F4A F6A lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 7 1/4 8 1/4 A Aluminum 6E ps Global model 20D 25N E/25 25X E/30H EK25/C 30D F25D US/CA model F25A Global model F20D US/CA model lade Dia. (in) Pitch (in) Mark Material Part number Remarks 3 9 1/8 12 F S-Steel /8 13 F S-Steel RELIANCE SERIES PROPELLERS (STD) PS Global model 150A 200A 250G US/CA model Global model F150A/ F200 F200C F225 F225C F250A F250G US/CA/ANZ model F150A F200A F225A F250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 17 M S-steel 68F /4 18 M S-steel 68F /4 19 M S-steel 68F /4 21 M S-steel 68F L150 L250 ps Global model L150A L200A L250G US/CA model Global model FL150A/ FL200 FL200C FL225 FL250A FL250G US/CA/ANZ model LF150A LF200A LF225A LF250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 17 ML S-steel 68G /4 18 ML S-steel 68G /4 19 ML S-steel 68G /4 21 ML S-steel 68G

79 2014 PROPELLER APPLICATIONS RELIANCE SERIES PROPELLERS (Shift Dampener System [SDS]) PS Global model 150A 200A 250G US/CA model Global model F150A/ F200 F200C F200F F200G F225 F225C F225F US/CA/ANZ model F150A F200A F200 F200CA F225A F225CA Global model F250A F250D F250G F300 US/CA/ANZ model F250A F250CA F300CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks /2 15 M S-steel 68F /4 17 M S-steel 68F /4 18 M S-steel 68F /4 19 M S-steel 68F /4 21 M S-steel 68F * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6CE ). L150 L300 ps Global model L150A L200A L250G US/CA model Global model FL150A/ FL200 FL200C FL200F FL200G FL225 FL225F FL250A US/CA/ANZ model LF150A LF200A LF200 LF200CA LF225A LF225CA LF250A Global model FL250G FL250D FL300 US/CA/ANZ model LF250CA FL300CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks /2 15 ML S-steel 68G /4 17 ML S-steel 68G /4 18 ML S-steel 68G /4 19 ML S-steel 68G /4 21 ML S-steel 68G * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6CE ). 2-15

80 2014 PROPELLER APPLICATIONS SALTWATER SERIES PROPELLERS ps Global model 150A 200A US/CA model Global model F150A/ 250G F200 F200C F225 F225C F250A F250G US/CA/ANZ model F150A F200A F225A F250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 M S-Steel 6R A /4 17 M S-Steel 6R A /4 19 M S-Steel 6R A /8 21 M S-Steel 6R A /2 23 M S-Steel 6R A0 L150 L250 ps Global model L150A L200A L250G US/CA model Global model FL150A/ FL200 FL200C FL225 FL250A FL250G US/CA/ANZ model LF150A LF200A LF225A LF250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 ML S-Steel 6R A /4 17 ML S-Steel 6R A /4 19 ML S-Steel 6R A /8 21 ML S-Steel 6R A /2 23 ML S-Steel 6R A0 2-16

81 2014 PROPELLER APPLICATIONS SALTWATER SERIES II PROPELLERS (STD) ps Global model 200A 250G US/CA model Global model F150A/ F200 F200C F225 F225C F250A F250 F250G US/CA/ANZ model F150A F200A F225A F250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 T S-Steel 6D For V6 3.1/3.3L model. (*1) /2 17 T S-Steel 6D /4 19 T S-Steel 6D T S-Steel 6D /4 23 T S-Steel 6D (*1) The blade contacts 6J9 lower-case. L150 L300 ps Global model L150A L200A L250G US/CA model Global model FL150A/ FL200 FL200C FL200F FL225 FL250A FL250G US/CA/ANZ model LF150A LF200A LF200 LF225A LF250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 TL S-Steel 6D For V6 3.1/3.3L model. (*1) /2 17 TL S-Steel 6D /4 19 TL S-Steel 6D TL S-Steel 6D /4 23 TL S-Steel 6D (*1) The blade contacts 6J9 lower-case. 2-17

82 2014 PROPELLER APPLICATIONS SALTWATER SERIES II PROPELLERS (Shift Dampener System [SDS]) ps Global model 150A 200A 250G US/CA model Global model F150A/ F175A F200 F200C F200F F200G F225 F225C US/CA/ANZ model F150A F175A F200A F200 F200CA F225A Global model F225F F250A F250G F250D F300 US/CA/ANZ model F225CA F250A F250CA F300CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 13 T S-Steel 6CE For V6 3.1/3.3/4.2L, L4 2.8L model. (*1) /4 15 T S-Steel 6CE For V6 3.1/3.3/4.2L, L4 2.8L model. (*1) /2 16 T S-Steel 6CE /2 17 T S-Steel 6CE /4 18 T S-Steel 6CE /4 19 T S-Steel 6CE T S-Steel 6CE T S-Steel 6CE /4 22 T S-Steel 6CE /4 23 T S-Steel 6CE * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6CE ). (*1) The blade contacts 6J9 lower-case. L150 L300 ps Global model L150A L200A L250G US/CA model Global model FL150A/ FL200 FL200C FL200F FL200G FL225 FL225F FL250A US/CA/ANZ model LF150A LF200A LF200 LF200CA LF225A F225CA LF250A Global model FL250G FL250D FL300 US/CA/ANZ model LF250CA LF300CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 13 TL S-Steel 6CF For V6 3.1/3.3/4.2L model. (*1) /4 15 TL S-Steel 6CF For V6 3.1/3.3/4.2L model. (*1) /2 17 TL S-Steel 6CF /4 18 TL S-Steel 6CF /4 19 TL S-Steel 6CF TL S-Steel 6CF TL S-Steel 6CF /4 22 TL S-Steel 6CF /4 23 TL S-Steel 6CF * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6CE ). (*1) The blade contacts 6J9 lower-case. 2-18

83 2014 PROPELLER APPLICATIONS SALTWATER SERIES HS4 PROPELLERS (STD) ps Global model 150A 200A 250G US/CA model Global model F150A/ F200 F200C F225A F225 F225C F250A F250 US/CA/ANZ model F150A F200A F225A F250A Global model F250G US/CA/ANZ model lade Dia. (in) Pitch (in) Mark Material Part number Remarks T S-Steel 6R T S-Steel 6R T S-Steel 6R L150 L300 ps Global model L150A L200A L250G US/CA model Global model FL150A/ FL200 FL200C FL200F FL225 FL250A FL250G US/CA/ANZ model LF150A LF200A LF200 LF225A LF250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks TL S-Steel 6S TL S-Steel 6S TL S-Steel 6S SALTWATER SERIES HS4 PROPELLERS (Shift Dampener System [SDS]) ps Global model 150A 200A 250G US/CA model Global model F150A/ F200 F200C F200F F200G F225 F225C F225F US/CA/ANZ model F150A F200A F200 F200CA F225A F225CA Global model F250A F250G F250G F250D F300 US/CA/ANZ model F250A F250CA F300CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks T S-Steel 6CE T S-Steel 6CE T S-Steel 6CE * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6CE ). L150 L300 ps Global model L150A L200A L250G US/CA model Global model FL150A/ FL200 FL200C FL200F FL200G FL225 FL225F FL250A US/CA/ANZ model LF150A LF200A LF200 LF200CA LF225A LF225CA LF250A Global model FL250G FL250D FL300 US/CA/ANZ model LF250CA LF300CA lade Dia. (in) Pitch (in) Mark Material Part number Remarks TL S-Steel 6CF TL S-Steel 6CF TL S-Steel 6CF * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6CE ). 2-19

84 2014 PROPELLER APPLICATIONS SALTWATER SERIES XL PROPELLERS (Shift Dampener System [SDS]) 350 ps (V8 engine) Global model F350A US/CA/ANZ model F350C lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 X S-Steel 6AW /4 17 X S-Steel 6AW /2 19 X S-Steel 6AW /4 21 X S-Steel 6AW /4 23 X S-Steel 6AW * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6AW ). L350 ps (V8 engine) Global model FL350A US/CA/ANZ model LF350C lade Dia. (in) Pitch (in) Mark Material Part number Remarks /4 15 XL S-Steel 6AX /4 17 XL S-Steel 6AX /2 19 XL S-Steel 6AX /4 21 XL S-Steel 6AX /4 23 XL S-Steel 6AX * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6AW ). SALTWATER SERIES XL4 PROPELLERS (Shift Dampener System [SDS]) 350 ps (V8 engine) Global model FL350A US/CA/ANZ model LF350C lade Dia. (in) Pitch (in) Mark Material Part number Remarks /8 15 X S-Steel 6AW /8 17 X S-Steel 6AW /8 22 X S-Steel 6AW /8 24 X S-Steel 6AW * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6AW ). L350 ps (V8 engine) Global model FL350A US/CA/ANZ model LF350C lade Dia. (in) Pitch (in) Mark Material Part number Remarks /8 15 XL S-Steel 6AX /8 17 XL S-Steel 6AX /8 22 XL S-Steel 6AX /8 24 XL S-Steel 6AX * Shift Dampener System (SDS) propeller requires the exclusive spacer (P/N: 6AW ). 2-20

85 2014 PROPELLER APPLICATIONS VMAX SERIES PROPELLERS ps (SHO engine) Global model F150C F165A F200D F225D F250C F225G F250F F275A US/CA/ANZ model VF150A VF200A VF225A VF250A lade Dia. (in) Pitch (in) Mark Material Part number Remarks /8 22 T1 S-Steel 6C Ventless /8 23 T1 S-Steel 6C Ventless /8 24 T1 S-Steel 6C Ventless /8 25 T1 S-Steel 6C Ventless /8 26 T1 S-Steel 6C Ventless /8 27 T1 S-Steel 6C Ventless /4 29 T1 S-Steel 6C Ventless PERFORMANCE SERIES PROPELLERS ps Global model 55D 60F E60H 70 75/85A E75 90A 115/C US/CA model Global model E115A 130/140 F40G FT50C FT50J FT60G F70A F75/C US/CA model T50 T60 F70A F75A Global model F80 F90 F95A F100 F100D F115A US/CA model F90A F115A Global model F115 US/CA/ANZ model F115 lade Dia. (in) Pitch (in) Mark Material Part number Remarks /2 17 K S-Steel 62A /2 19 K S-Steel 62A /2 21 K S-Steel 62A /2 23 K S-Steel 62A ps Global model Z150Q US/CA model VZ150 lade Dia. (in) Pitch (in) Mark Material Part number Remarks /2 21 M S-Steel 66K /2 23 M S-Steel 66K /2 25 M S-Steel 66K /2 27 M S-Steel 66K

86 2014 PROPELLER APPLICATIONS HIGH PERFORMANCE SERIES PROPELLERS ps Global model 60F 70 75/85A 75C 90A 115/C 130/140 Z150Q US/CA model VZ150 Global model 150A 200A US/CA model lade Dia. (in) Pitch (in) Mark Material Part number Remarks P S-Steel 6E Special purpose P S-Steel 6E Special purpose P S-Steel 6E Special purpose P S-Steel 6E Special purpose P S-Steel 6E Special purpose * For L-transom engine matching sports boat. 2-22

87 WOT OPERATION RANGE TALE With WOT (Wide-Open-Throttle) operation and under a maximum boat load, the engine RPM should be within the upper half of the WOT speed range. Select a propeller which fulfills this requirement. 2-stroke engines Global Model US/CA Model WOT range (rpm) 2C 4,000 5,000 3A 4,500 5,500 4AC, 5C, 5CS 4,500 5,500 6C 4,000 5,000 8C 4,500 5,500 E8D, EK8D 4,500 5, F, 15F, E9.9D, E15D, EK9.9D, EK15D, EK9.9J, EK15P 4,500 5,500 20D, 25N 5,000 6,000 30D 4,500 5,500 E/25, E/30H, 25X, EK25, EK25C 4,500 5,500 EK40G, E40G, EK40J, E40J 4,500 5,500 E/40X 4,500 5,500 40V, 50H 4,500 5,500 E48C, E55C, 55 4,500 5,500 E60H, 60F 4,500 5, ,000 6,000 55D, 75A, E75, 75C, 85A, 90A 4,500 5,500 E115A, 115, 115C, 140 4,500 5, ,000 6,000 L/150A, L/200A 4,500 5,500 Z150Q, Z200P VZ150 4,500 5,500 L/250G 4,500 5,500 4-stroke engines Global Model US/CA Model WOT range (rpm) F2A, F2.5A F2.5A 5,250 5,750 F4 F4A 4,000 5,000 F5A, F6C F6A 4,500 5,500 F8C, FT8D, F9.9J, FT9.9L F8A, F9.9, T9.9 5,000 6,000 F9.9H, F15C, F20, F20C F15A, F20A 5,000 6,000 F20D, F25D, FT25F F25A/, T25A 5,000 6,000 F30, F40F F30A, F40A 5,000 6,000 FT50C, F50D 5,000 6,000 F40H, F50H, FT50J, F60F, FT60G F50, T50, F60, T60 5,000 6,000 F70A, F40G F70A 5,300 6,300 F95A, F100 5,000 6,000 F75, F75C, F80, F90, F100D F75A, F90A 5,000 6,000 F/FL115A F/LF115A 5,000 6,000 To be continued. 2-23

88 WOT OPERATION RANGE TALE 4-stroke engines Global Model US/CA/ANZ Model WOT range (rpm) F/FL115 F/LF115 5,300 6,300 F/FL150A F/LF150A 5,000 6,000 F/FL150 4,500 5,500 F150C, F165A VF150A 5,000 6,000 F175A, F/FL200, F/FL200C, F/FL200F, F/FL200G, F/FL225, F225C, F/FL250A, F/FL250G F175A, F/LF200A, F/LF200, F/LF200CA, F/LF225A, F/LF250A 5,000 6,000 F200D, F225D, F250C, F225G, F250F, F275A VF200LA, VF225LA, VF250LA 5,000 6,000 F/FL225F, F/FL250D, F/FL300 F/LF225CA, F/LF250CA, F/LF300CA 5,000 6,000 F/FL350A F/LF350C 5,000 6,000 If the engine RPM exceeds the recommended WOT range, replace with a larger pitch propeller. If the engine RPM does not reach the recommended WOT range, replace with a smaller pitch propeller. NOTICE Do not run the engine at a speed which exceeds WOT range, as the engine could be damaged from overload or over rev. * The engine rpm at WOT operation will be usually changed about 150 rpm if the pitch of propeller has been changed one inch. However, the change of rpm varies due to the propeller type, water type (salt or freshwater), boat type (weight or hull shape), etc. * The maximum engine RPM will increase when the outboard motor is trimmed out. 2-24

89 REMOTE CONTROLS REMOTE CONTROL TYPES AND APPLICATIONS SIDE MOUNT REMOTE CONTROL [Mechanical RC] INNACLE MOUNT REMOTE CONTROL [Mechanical RC] X3 CONCEALED REMOTE CONTROL [Mechanical RC] X5 INNACLE MOUNT REMOTE CONTROL [Mechanical RC] (FOR US) X6 INNACLE MOUNT REMOTE CONTROL [DEC] X7 CONCEALED REMOTE CONTROL [DEC] REMOTE SWITCH TYPES AND APPLICATIONS COMINATION SWITCH PANEL (IG SWITCH AND EMERGENCY STOP SWITCH) INDEPENDENT SWITCH PANEL ADAPTER FOR EMERGENCY STOP SWITCH LEAD ENGINE SHUT-OFF LANYARD (CORD) PTT SWITCH PANEL REMOTE CONTROL CALES SELECTING THE CALE LENGTH REMOTE CONTROL CALES ROUTING THE REMOTE CONTROL CALES REMOTE CONTROL THROTTLE CALE FREE-PLAY ADJUSTMENT REMOTE CONTROL ATTACHMENT KIT STEERING HOOK STEERING GUIDE ATTACHMENT KIT TIE-AR KIT CONVENTIONAL WIRE HARNESS SWITCH PANEL HARNESS TO 10-PIN ADAPTER MAIN HARNESS EXTENSION DIGITAL ELECTRONIC REMOTE CONTROL WIRE HARNESS MAIN WIRE HARNESS DUAL STATION WIRE-HARNESS (3-4-6P) DUAL STATION WIRE-HARNESS (2-12P) DUAL STATION WIRE-HARNESS (3-12P) CONVERSION HARNESS L CONVERSION HARNESS M CONVERSION HARNESS N CONVERSION HARNESS P

90 REMOTE CONTROL TYPES AND APPLICATIONS A Yamaha outboard motor has one of two throttle control systems, either Push To Open or Pull To Open. For example, Push To Open means the throttle valve opens when the remote control inner cable is extended and then the throttle arm is pushed. Most models have Push To Open system. However, some following models have Pull To Open system. Pull to Open models 25 20D 25N E25 30D 30H E30H E40J EK40J E40G 55 E60H The 10-pin connector is usually used for PTT and/or PT (Power Tilt) models. The 7-pin connector is for manual tilt models. ut, F9.9J (F9.9), FT9.9L (T9.9), F15C (F15A) and F20 (F20A) have the 10-pin connector. Install the remote control box so that there is sufficient clearance between steering wheel and remote control lever operation area. 3-2

91 REMOTE CONTROL TYPES AND APPLICATIONS 703 SIDE MOUNT REMOTE CONTROL [Mechanical RC] Designed to be compatible with most of the Yamaha Outboard motor models. This remote control can be fitted in almost every type of boat. The basic control functions are contained in the 703 remote control box. Part No. Throttle Coupler Mount Choke PTT Push Pull 7-pin 10-pin 2-pin R L Remarks A A For analog gauge only A For additional trim SW A For analog gauge only For additional trim SW Successor model of 701 RC Successor model of 701 RC Twin attachment kit For twin engine application * Throttle opening direction (PUSH-PULL) can be reversed. * Control lever position (R-L) can be changed to its opposite side. * 13 mm (0.5 in) thickness spacer is included in the remote control package. * A 4.5 m (15 ft) wire harness (10-pin) is attached to the remote control box. * For further information, see the instruction (P/N: or 33) in the package. 3-3

92 REMOTE CONTROL TYPES AND APPLICATIONS 703 SIDE MOUNT REMOTE CONTROL DIMENSIONS mm (in.) 70 (22.76) 30 (1.18) 226 (8.9) 85 (3.35) 86 (3.39) (4.59) 46 (1.81) 128 (5.04) 56 (2.2) 135 (5.31) 16 (0.63) 40 (1.57) 64.5 (2.54) 85.5 (3.37) 3-4

93 REMOTE CONTROL TYPES AND APPLICATIONS 704 INNACLE MOUNT REMOTE CONTROL [Mechanical RC] Designed for use with electric start models. est fitted to a boat with center console. Two types of levers, Single lever or Twin lever, are available to match the purpose of use and engine applications. Two types of control boxes, Premium or Standard type, are also available to match the boat design, cost, etc. 1 2 Ref. Throttle Lever Part No. PTT No. Push Pull R L Twin Remarks P1 1 1 Premium P Premium P Premium P Premium * Switch panel and extension wire-harness are required to connect to the engine 10-pin harness. * Throttle opening direction can be reversed. * Lever location can be changed to its opposite position. * For further information, see the instruction (P/N: P0) in the package. 3-5

94 REMOTE CONTROL TYPES AND APPLICATIONS 704 INNACLE MOUNT REMOTE CONTROL DIMENSIONS Single lever Twin lever (7.07) mm (in.) (4.07) 90 (3.54) mm (in.) 94.5 (3.72) 74 (2.91) 70 (2.76) 105 (4.13) 94.5 (3.72) 126 (4.96) (7.38) 70 (2.76) 33 (1.30) 33 (1.30) 212 (8.35) 106 (4.17) 213 (8.39) 213 (8.39) 39 (1.54) (5.32) 212 (8.35) 106 (4.17) 39 (1.54) (5.32) R3 6 (0.23) 6 (0.23) 10 (0.39) R10 57 (2.24) 138 (5.43) 153 (6.02) 10 (0.39) 55 (2.16) 108 (4.25) 138 (5.43) 153 (6.02) (4.29) Cut out the shaded area Cut out the shaded area 3-6

95 REMOTE CONTROL TYPES AND APPLICATIONS REMOTE CONTROL SPACER Designed to raise the control box 22 mm (0.9 in.) to make more clearance between the lever and the dash board when the lever is in the WOT position. (1) (2) Ref. No. Part No. Descriptions Single Twin 6X3 CONCEALED REMOTE CONTROL [Mechanical RC] Designed for the electric start models. est fitted to runabout type boats. The emergency shut-off switch is incorporated into the control box. The mounting position can be selected from horizontal or inclined 30-degree up or down position depending on the boat design. Throttle Mount Part No. PTT Push Pull R L 6X Remarks With emergency shut-off cord (2-pin coupler) * The ignition switch panel without engine shut-off cord and 10-pin main harness are required to connect to the engine. * Throttle opening direction can be reversed. * For further information, see the instruction in the package. 3-7

96 REMOTE CONTROL TYPES AND APPLICATIONS 6X3 CONCEALED REMOTE CONTROL DIMENSIONS 54.2 (2.13) 251 (9.88) mm (in.) 67.6 (2.66) 88 (3.46) 201 (7.91) (7.81) 29.6 (1.17) (0.8) 20.4 Max. 30 (1.18) 52.3 (2.06) 60.1 (2.37) 89 (3.5) 123 (4.84) 12 (0.47) (1.29) If a panel board thickness is below 20 mm (0.79 in.), make three 7 mm (9/32 in.) holes and use the supplied bolts and nuts. If the board is thicker than 20 mm (0.79 in.), make three 4 mm (5/32 in.) holes and use supplied screws (1.83) 99 (3.89) (3.03) (1.64) 42 (1.65) 28.6 (1.12) 13 (0.51) 60.1 (2.36) Cut out the shaded area. 3-8

97 REMOTE CONTROL TYPES AND APPLICATIONS 6X5 INNACLE MOUNT REMOTE CONTROL [Mechanical RC] (FOR US) This unique binnacle-mount remote control is designed for triple engine application for F225 and F250 with mechanical remote control. Can be used only in conjunction with the genuine triple-switch panel and Digital Network Gauge System (6Y8). Throttle Mount Part No. PTT Push Pull R L 6X Remarks * Yamaha remote control cable, Premier Series, or equivalent cable (Teleflex CC3300) is recommended for 6X5 remote control box. * Premier Series is handled by Yamaha Motor Corporation, USA. * For further information, see the instruction (P/N: 6X P0) included in the package. 3-9

98 REMOTE CONTROL TYPES AND APPLICATIONS 6X5 INNACLE MOUNT REMOTE CONTROL DIMENSIONS mm (in.) 32 R N F Max (9.88) 18 (0.71) 267 (10.51) Max (9.92) 179 (7.05) 200 (7.87) 223 (8.78) 176 (6.93) 172 (6.77) 205 (8.07) 172 (6.77) 86 (3.39) φ6 (0.24) R3 (0.12) * If the mounting board is thinner than 20 mm (0.8 in.), make four 6 mm (0.24 in.) diameter holes and secure the remote control box with the supplied bolts and nuts. If the supplied tapping screws are used, make four 3.5 mm (0.14 in.) diameter holes. 200 (7.87) 100 (3.94) Cut off shaded area 83 (3.27) 100 (3.94) 183 (7.20) OW Template 3-10

99 REMOTE CONTROL TYPES AND APPLICATIONS 6X6 INNACLE MOUNT REMOTE CONTROL [DEC] This exclusive binnacle remote control unit requires no mechanical remote control cables. The throttle and shift operations are electrically controlled by new Digital Network System, which will obtain smoother remote control operation without cable friction. Rigging has been simplified, because the mechanical cable installation and adjustment are not required. These remote control units cover single, twin, triple and quad engine applications Ref. No Part No. Variation code Engine Single Twin Triple Quad Single station Dual station Main station helm 2nd station helm Remarks 6X A 1 1 Single station only 6X C X G 1 1 6X Single station only 6X D X H 1 1 6X F X K 1 1 6X L w/ PTT SW panel 6X M 1 1 w/ PTT SW panel * For further information, see the instruction which is included in the remote control package. * Quad engine RC is applicable to F/LF225CA, F/LF250CA, F/LF300CA and F/LF350CA/ for US. 3-11

100 REMOTE CONTROL TYPES AND APPLICATIONS DEC ENGINE SELECTION This RC unit accepts all DEC engines. The initial setting is completed to match new DEC engines. If this RC unit is used for previous DEC engines such as F250 and F300 (V8) for 2011 model, follow the procedure below. 1. Remove the black cap. 2. Disconnect the white coupler, and connect it to the black coupler. 3. Attach the black cap to the white coupler for waterproofing. * If the re-setting is wrong, the engine will not start. * The RC unit with variation code [A] is not required for setting to select the engine. Example: twin engine application WIRE-HARNESS For previous DEC engine LK For previous DEC engine LK Cap Cap r P P S S r WHT For new DEC engine (initial setting) WHT For new DEC engine (initial setting) 3-12

101 REMOTE CONTROL TYPES AND APPLICATIONS 6X6 INNACLE MOUNT REMOTE CONTROL DIMENSIONS The side view is the same among all remote control unit variation. mm (in.) Throttle range 22.5 deg. F Shift range 5 deg. N Shift range 22.5 deg. R Throttle range Max. 90 deg. 225 (8.86) 35 (1.38) 170 (6.69) Max. 67 deg. 128 (5.04) 182 (7.17) Single engine application 145 (5.71) 5.5 (0.22) 132 (5.20) 106 (4.17) Cut out shaded area 59 (2.32) 62 (2.44) Template (single lever) To be continued. 3-13

102 REMOTE CONTROL TYPES AND APPLICATIONS Twin engine application 145 (5.71) mm (in.) 5.5 (0.22) 132 (5.20) 172 (6.77) Cut out shaded area 102 (4.02) 105 (4.13) Template (twin lever) Triple engine application 116 (4.57) 145 (5.71) 100 (3.93) 5.5 (0.22) 132 (5.20) 172 (6.77) Cut out shaded area 102 (4.02) 105 (4.13) 208 (8.19) 149 (5.87) Template (same as twin engine) 41 (1.61) Center RC ECM bracket * ECM wire harness length: Approx. 1.5 m (5 ft) To be continued. 3-14

103 REMOTE CONTROL TYPES AND APPLICATIONS Quad engine application mm (in.) 116 (4.57) 172 (6.77) 100 (3.93) 145 (5.71) 132 (5.20) 6 (0.24) 208 (8.19) 149 (5.87) 102 (4.02) 105 (4.13) 41 (1.61) ECM for C-PORT/ C-STD * ECM wire harness length: Approx. 1.5 m (5 ft) Template for RC unit 304 (12) 115 (4.53) 14 (0.55) 37 (1.48) 87 (3.43) W G P X X X Y L Or LR G 812 (32) 99 (3.90) 94 (3.70) R10 (0.39) 6 (0.24) 66 (2.60) 71 (2.80) Template for PTT SW 3-15

104 REMOTE CONTROL TYPES AND APPLICATIONS 6X7 CONCEALED REMOTE CONTROL [DEC] This exclusive concealed remote control unit requires no mechanical remote control cables. The throttle and shift operations are electrically controlled by new Digital Network System, which will obtain smoother remote control operation without cable friction. Rigging has been simplified, because the mechanical cable installation and adjustment are not required. Part No. Variation code Engine Mount Single Twin Triple R L 6X A 1 1 Remarks With engine shut-off SW * Ignition switch panel (P/N: 64D ) is required. * Dual-station system is not acceptable. * For further information, see the instruction which is included in the remote control unit package. 3-16

105 REMOTE CONTROL TYPES AND APPLICATIONS 6X7 CONCEALED REMOTE CONTROL DIMENSIONS 96.2 (3.79) 18 (0.71) 57 (2.24) 27 (1.06) mm (in.) 130 (5.12) 170 (6.69) Mount board 155 (6.10) 22.5 deg. Shift range N Shift range 22.5 deg. F R Throttle range * Stop SW wire harness length: Approx. 2 m (6.5 ft) Throttle range Max. 67 deg (2.14) Max. 90 deg. 38 (1.50) 56.5 (2.22) 6.4 (0.25) 35 (1.38) 116 (4.57) 59.5 (2.34) 16.5 (0.65) 95 (3.74) 17.5 (0.69) 39.5 (1.56) 213 (8.39) M6 tapping mount screw 40.5 (1.59) Template 43 (1.69) 12.7 (0.50) Make three 7 mm (9/32 in) holes for mounting with bolts and nuts. Drill 4 mm (5/32 in) holes for tapping screws, if the board is thicker than 20 mm (0.79 in). ECM bracket * ECM wire harness length: Approx. 1.5 m (5 ft) 3-17

106 REMOTE SWITCH TYPES AND APPLICATIONS COMINATION SWITCH PANEL (IG SWITCH AND EMERGENCY STOP SWITCH) SINGLE IG SWITCH W/ PANEL Ref. No. Part No. Description w/ choke SW 6R w/o choke SW, For Prime start model or Digital Network System (6Y8) 2 6X For Digital Network System (6Y8), Main station helm 3 6X For Digital Network System (6Y8), 2nd station helm 1 mm (in.) 51 (2.0) 93 (3.66) 44.5 (1.75) 24.3 (0.95) 5.6 (0.22) Cut out shaded area 25.5 (1.0) 54 (2.12) 110 (4.33) 68 (2.68) 101 (3.98) (W) W() 140 (5.51) 355 (13.98) Y P W r R G Y L R G 2 mm (in.) 97.4 (3.83) 53 (2.09) 5.6 (0.22) 114 (4.49) 12 (0.47) 49.4 (1.94) 66 (2.60) 54 (2.13) 100 (4.00) Cut out shaded area To be continued. 3-18

107 REMOTE SWITCH TYPES AND APPLICATIONS SINGLE IG SWITCH W/ PANEL 3 51 (2.0) mm (in.) 25.5 (1.0) 68 (2.68) 86 (3.39) 113 (4.49) 24 (0.94) 24 (0.94) 5.5 (0.22) 52.4 (2.06) Cut out shaded area 130 (5.12) 140 (5.51) r W Y P Or SINGLE IG SWITCH W/O PANEL Ref. No. Part No. Description C-01 With choke switch 1 mm (in.) Max. 4 (0.16) 101 (3.98) 20 (0.79) 16 (0.63) 3.5 Nm, 0.35 kgf m, 2.6 ft lb (W) W() 140 (5.51) Max. 4 (0.16) 355 (13.98) Y P W r R G Y L R G 3-19

108 REMOTE SWITCH TYPES AND APPLICATIONS TWIN IG SWITCH Ref. No. Part No. Description 1 6K w/ choke SW w/o choke SW 2 6Y For Digital Network System (6Y8), Main station helm 3 6X For Digital Network System (6Y9), Main station helm 4 6X For Digital Network System (6Y8), 2nd helm 5 6X For Digital Network System (6Y9), main station helm, w/o buzzer, Requires [No.3] 6X E0 For Digital Network System (6Y9), 2nd station helm, w/ buzzer (5.04) 25.9 (1.02) 145 (5.71) 97 (3.82) mm (in.) 93 (3.66) (0.95) 110 (4.33) 5.6 (0.22) 54 (2.13) Cut out shaded area Y P 110 (4.33) 140 (5.51) 340 (13.39) W L R r G Y G R (0.22) 113 (4.45) 66 (2.60) 25 (0.98) 154 (6.06) *110 (4.33) mm (in.) 3.3 (0.13) 50 (1.97) Cut out shaded area 138 (5.43) 54 (2.13) 66 (2.60) 338 (13.3) *For reference To be continued. 3-20

109 REMOTE SWITCH TYPES AND APPLICATIONS TWIN IG SWITCH 3 mm (in.) 97.4 (3.83) 53 (2.09) 5.6 (0.22) 114 (4.49) 12 (0.47) 109 (4.29) 25 (0.98) 25 (0.98) 126 (4.96) 113 (4.45) 24 (0.94) 24 (0.94) 49.4 (1.94) 66 (2.60) 54 (2.13) 100 (4.00) Cut out shaded area 4 mm (in.) 86 (3.39) Cut out shaded area 52.4 (2.06) 130 (5.12) 140 (5.51) 5.5 (0.22) r W Y P Or 5 mm (in.) 70.4 (2.77) 28.3 (1.11) 38.4 (1.51) 5.6 (0.22) 87 (3.42) 55 (2.17) 61.5 (2.42) 12 (0.47) (1.75) Cut out shaded area 3-21

110 REMOTE SWITCH TYPES AND APPLICATIONS TRIPLE IG SWITCH Ref. No. Part No. Description 1 6X For Digital Network System (6Y8), Main station helm 2 6X For Digital Network System (6Y9), Main station helm 3 6X For Digital Network System (6Y8), 2nd station helm 4 6X For Digital Network System (6Y9), main station helm, w/o buzzer, Requires [No.2] 6X F0 For Digital Network System (6Y9), 2nd station helm, w/ buzzer (5.04) mm (in.) 25.9 (1.02) 145 (5.71) 93 (3.66) (0.95) 5.5 (0.22) Cut out shaded area 54 (2.13) 110 (4.33) 510 (20.08) 370 (14.57) *130 (5.12) (3.83) * Minimum mounting depth (for reference) mm (in.) 53 (2.09) 5.6 (0.22) 114 (4.49) 12 (0.47) 49.4 (1.94) 66 (2.60) 54 (2.13) 100 (4.00) Cut out shaded area To be continued. 3-22

111 REMOTE SWITCH TYPES AND APPLICATIONS TRIPLE IG SWITCH (6.57) 25 (0.98) 25 (0.98) mm (in.) 113 (4.45) Cut out shaded area 184 (7.24) 130 (5.12) 24 (0.94) 24 (0.94) 52.4 (2.06) 5.5 (0.22) 86 (3.39) 140 (5.51) r W Y P Or 4 mm (in.) 97.4 (3.83) 114 (4.49) 55.2 (2.17) 55 (2.17) 61.5 (2.42) 12 (0.47) 38.4 (1.51) 5.6 (0.22) (1.75) Cut out shaded area 3-23

112 REMOTE SWITCH TYPES AND APPLICATIONS QUAD IG SWITCH Ref. No. Part No. Description 6X M2 For Digital Network System (6Y9), Main station helm, Assembly for P, CP, CS and S as below* 1 *6X R2 For P engine *6X S2 For CP engine *6X T2 For CS engine *6X U2 For S engine 2 6X J0 For Digital Network System (6Y9), 2nd station helm, P/CP engine 6X K0 For Digital Network System (6Y9), 2nd station helm, CS/S engine 1 P/ CS SW PANEL EX: P SW panel 47 (1.85) 63 (2.48) 9 (0.35) (4.59) mm (in.) 47 (1.85) 63 (2.48) 5.6 (0.22) 54 (2.13) (*1) (*1) CS SW panel has CS mark. 140 (5.51) 665 (26.2) P W Y r W L G R (*1) CP/ S SW PANEL EX: CP SW panel 47 (1.85) 63 (2.48) 9 (0.35) Y R RY (4.59) mm (in.) 47 (1.85) 63 (2.48) 5.6 (0.22) 54 (2.13) (*1) (*1) S SW panel has S mark. R G 140 (5.51) 595 (23.4) P W Y r W L G R (*1) YR 3-24

113 REMOTE SWITCH TYPES AND APPLICATIONS QUAD IG SWITCH 2 mm (in.) EX: P/CP SW panel 61.5 (2.42) P L/W r Y L/W P Y r 450 (17.7) 12 (0.47) 87 (3.43) The recognition letter such as P, CP, S, CS is stamped on the surface protection film. 55 (2.17) 70.4 (2.77) 28.3 (1.11) 5.6 (0.22) 38.4 (1.51) 44.5 (1.75) Cut out shaded area 3-25

114 REMOTE SWITCH TYPES AND APPLICATIONS INDEPENDENT SWITCH PANEL IG SWITCH W/ PANEL Ref. No. Part No. Description 1 64D w/ bullet connectors for emergency stop SW 2 64D w/ 2P coupler for emergency stop SW, For 6X3 & 6X7 RC 3 6X For Digital Network System (6Y9), 2nd station helm, Single engine application 4 6X C0 For Digital Network System (6Y9), Multi engine application (All engine start/stop) 1 47 (1.85) 63 (2.48) 9 (0.35) (4.59) 69.5 (2.74) mm (in.) 47 (1.85) 63 (2.48) 5.6 (0.22) 54 (2.12) 140 (5.51) 355 (13.98) Y P W To stop S/W W r R G Y L R G 2 mm (in.) 47 (1.85) 63 (2.48) 9 (0.35) (4.59) 69.5 (2.74) 47 (1.85) 63 (2.48) 5.6 (0.22) 54 (2.12) 140 (5.51) 355 (13.98) Y P W To stop S/W W r R G Y L R G To be continued. 3-26

115 REMOTE SWITCH TYPES AND APPLICATIONS IG SWITCH W/ PANEL 3 mm (in.) 33.4 (1.31) 5.6 (0.22) 38.4 (1.51) 50 (1.97) 55 (2.17) 61.5 (2.42) 12 (0.47) 38.1 (1.5) Y P r 4 mm (in.) 33.4 (1.31) 5.6 (0.22) 38.4 (1.51) 50 (1.97) 55 (2.17) 61.5 (2.42) 12 (0.47) 38.1 (1.5) r r r Y 3-27

116 REMOTE SWITCH TYPES AND APPLICATIONS IG SWITCH W/O PANEL Ref. No. Part No. Description w/bullet connectors for stop switch 2 6X w/2-pin coupler for stop switch, For 6X3 and 6X7 RC 1 mm (in.) Y W P r R Y G L R G W Y P To buzzer To stop SW 175 (6.89) Max. 4 (0.16) 380 (15) 2 mm (in.) Max. 4 (0.16) Y W To stop SW P r W L G R G Y R 140 (5.51) 355 (14) 3-28

117 REMOTE SWITCH TYPES AND APPLICATIONS EMERGENCY STOP SWITCH W/ PANEL Ref. No. Part No. Description 1 64D w/ bullet connectors for stop SW 2 64D w/ 2P coupler for stop SW 3 6X For Digital Network System (6Y9), 2nd station helm, Single/Twin/Triple engine application 4 6X V0 For Digital Network System (6Y9), Quad engine application only 1 47 (1.85) 63 (2.48) 9 (0.35) mm (in.) 47 (1.85) 5.6 (0.22) 54 (2.12) W 63 (2.48) 1000 (39.4) 2 47 (1.85) 63 (2.48) 9 (0.35) mm (in.) 47 (1.85) 5.6 (0.22) 54 (2.12) 63 (2.48) 1000 (39.4) W (1.31) 5.6 (0.22) 50 (1.97) mm (in.) (1.31) 5.6 (0.22) 50 (1.97) Clearance: mm, in 12 (0.47) 53 (2.07) mm (in.) 38.4 (1.51) 55 (2.17) 38.4 (1.51) 55 (2.17) 38.1 (1.5) (1000 (39.37)) WWW 38.1 (1.5) 1000 (39.4) WWW 3-29

118 REMOTE SWITCH TYPES AND APPLICATIONS EMERGENCY STOP SWITCH W/O PANEL Ref. No. Part No. Description w/bullet connectors for stop switch 2 64D w/2-pin coupler for stop switch (0.63) mm (in.) 16 (0.63) mm (in.) 3.5 Nm, 0.35 kgf m, 2.6 ft lb 250 (9.84) 3.5 Nm, 0.35 kgf m, 2.6 ft lb 1000 (39.4) Max. 4 (0.16) W Max. 4 (0.16) W 3-30

119 REMOTE SWITCH TYPES AND APPLICATIONS STATION SELECTOR SWITCH Ref. No. Part No. Description 1 6X A0 For Digital Network System (6Y8), Dual station 2 6X For Digital Network System (6Y9), Dual station, Single/Twin/Triple engine application 3 6X L0 For Digital Network System (6Y9), Dual station, Quad engine application only 1 68 (2.68) 51 (2.01) 37.2 (1.46) 110 (4.33) 22 (0.87) mm (in.) 66 (2.60) 49 (1.93) 5.5 (0.22) GGG 100 (3.94) (1.31) 5.6 (0.22) 38.4 (1.51) 50 (1.97) 55 (2.17) 61.5 (2.42) 12 (0.47) 38.1 (1.5) G G G (1.31) 5.6 (0.22) 50 (1.97) 61.5 (2.42) 12 (0.47) 38.4 (1.51) 55 (2.17) Y r 38.1 (1.5) 200 (7.87) 3-31

120 REMOTE SWITCH TYPES AND APPLICATIONS ADAPTER FOR EMERGENCY STOP SWITCH LEAD Ref. No. Part No. Description 1 6X pin coupler - bullet connector 2 6X ullet connector - 2-pin coupler (3.94) mm (in.) 100 (3.94) mm (in.) W W W W ENGINE SHUT-OFF LANYARD (CORD) Part No Description mm (in.) 1300 (51.2) PTT SWITCH PANEL Part No. Description For PTT models mm (in.) TRIM & TILT UP DOWN 62 (2.44) ON ON (32 ) G R L 960 (37.8) 19.2 (0.76) 10 (0.39) 3-32

121 REMOTE CONTROL CALES SELECTING THE CALE LENGTH Use the following examples as a guide for measurement. Obviously, different boats will require different routing, therefore different lengths are required. 1. Choose a mounting location for the remote control box which will provide comfortable operation and unobstructed movement of the hand lever and control mechanism. * Minimum clearance below the 704 binnacle mount remote control mounting surface for cables is 400 mm (16 in). Also, minimum clearance behind the 703 side mount remote control box for the control cables is 400 mm (16 in). 2. Measure from the control box position along an unobstructed path to shift and throttle connections in the motor. The cable lengths are overall length. When a measurement is in feet and inches, specify next whole foot. Add 3 feet for loop (see illustration below). Cable length = A feet A + C + 3 feet Obviously, different boats will require different routing, therefore different lengths are required. For example, a thru-transom boat is shown in the illustration below. REMOTE CONTROL CALES CALE TYPE Yamaha remote control cables are available in lengths from 6 feet to 27 feet. The cables utilize threaded ends. Part No. RC cable length Feet Meters * If Yamaha remote control cable is not available, a Teleflex Morse CC3300 (LK)/33C (RED) type cable is recommended. Cable length = A foot A + C + 1 foot * When the remote control cable is too long, neutral adjustment may be difficult due to increased free play. 3-33

122 REMOTE CONTROL CALES ROUTING THE REMOTE CONTROL CALES WARNING Do not bend the remote control cable to the radius of 300 mm (1 foot) or smaller. Additional friction will impair the control ability. 1. Route the cable along an unobstructed path of the hull from the remote control box to the engine. 2. Take 3 feet (approximately 1 m) of cable to make a loop in the motor well. This is to prevent the cables from hard bend when the outboard motor is fully tilted up and steered. See the illustration below for a typical cable routing. * Refer to the instruction manual packed in the remote control box for the installation and routing of the remote control cable. Loop REMOTE CONTROL THROTTLE CALE FREE-PLAY ADJUSTMENT The mechanical remote control cable free-play adjustment is required for proper remote throttle control operation. For the first, install the remote control cables to the remote control box, and put the remote control lever into the neutral/ idle position. * For detailed procedure to install the remote control cables to the remote control box, see the instruction which is supplied with the remote control unit, or applicable service literature. Adjust the inner cable free-play as follows: PUSH-TO-OPEN TYPE 1. Pull out the inner cable by the force of 15 N (1.5 kgf, 3 lb) to remove the cable free-play. 2. Set the throttle valve control arm to contact onto its stop plate. 3. Install the cable joint, and adjust it to align with the pin of throttle arm. 4. Connect the joint to the pin, and then secure it using the clips and nuts. 5. Check the throttle for proper operation. Engine side Pull [15 N, 1.5 kgf, 3 lb] PULL-TO-OPEN TYPE 1. Push in the inner cable by the force of 15 N (1.5 kgf, 3 lb) to remove the cable free-play. 2. Set the throttle valve control arm to the fully closed (idle) position. 3. Install the cable joint, and adjust it to align with the pin of throttle arm. 4. Connect the joint to the pin, and then secure it using the clips and nuts. 5. Check the throttle for proper operation. Engine side Push [15 N, 1.5 kgf, 3 lb] 3-34

123 REMOTE CONTROL ATTACHMENT KIT If the specified tightening torque for the bolts and nuts is not mentioned in the figure, use standard torque as follows. General torque table olt size Nm kgf m lb ft M M M Part No. 6G Global model 6C 8C US/CA model Part No. 6AH Global model F9.9H F15C F20 F20C US/CA model F15A F20A To be continued. 3-35

124 REMOTE CONTROL ATTACHMENT KIT Part No. 60R-G Global model F8C FT8D US/CA model F8A Part No Global model E8D EK8D US/CA model For ball post Part No. 63V Global model 9.9F 15F US/CA model Part No. 6DR Global model F9.9J FT9.9L US/CA model F9.9 T9.9 To be continued. 3-36

125 REMOTE CONTROL ATTACHMENT KIT Part No. 6L Part No D Global model US/CA model F25D F25A Global model E/25 25X E/30H US/CA model For ball post/ STR guide Part No. 6L Global model 20D 25N US/CA model Part No. Global model 30D 6J US/CA model To be continued. 3-37

126 REMOTE CONTROL ATTACHMENT KIT Part No. Global model US/CA model E/40X 66T

127 STEERING HOOK Part No. 63V Global model F8C FT8D 9.9F 15F US/CA model F8A For STR guide Part No. 6L Global model 20D 25N US/CA model For STR guide Part No. 6G Global model 9.9F 15F 30D US/CA model For ball post Part No. 65W Global model F20D F25D FT25F F30 F40F US/CA model F25A T25A F30A F40A Global model F40H F50H FT50J F60F FT60G US/CA model F50 T50 F60 T60 Global model F70A F40G E/40X US/CA model F70A For STR guide Part No. 6AH Global model F9.9H F15C F20 F20C US/CA model F15A F20A For STR guide Part No Global model E40J E40G EK40J EK40G US/CA model For STR guide To be continued. 3-39

128 STEERING HOOK Part No. 63D Global model 40V 50H FT50C F50D US/CA model For STR guide Part No. 68V Global model F75C F95A F100 F115A US/CA model F115A For STR guide Part No. 67F Global model F75 F80 F90 F100D US/CA model F75A F90A For STR guide Part No Global model 6C 8C E8D EK8D US/CA model For ball post Part No Global model 75A 85A 75C 90A US/CA model For STR guide Part No. Global model 30D US/CA model For ball post/ STR guide 6J To be continued. 3-40

129 STEERING HOOK Part No Global model E/25 25X E/30H US/CA model For ball post/ STR guide Part No. 6G Global model 9.9F 15F US/CA model For rope Part No Global model 6C 8C E8D EK8D E/25 US/CA model Global model 25X E/30H US/CA model For rope Part No. 69G Global model FT8D FT9.9L US/CA model T9.9 For linkage to main engine Part No. Global model US/CA/ANZ model 115 F115 F115 6EK

130 STEERING GUIDE ATTACHMENT KIT The locknut (1) for the steering cable joint should be loosen 1/4 turns from its seated position. This is to prevent the joint from friction when the outboard motor is steered. Part No. 63V Global model 9.9F 15F E9.9D E15D US/CA model Part No Global model E/25 E/30H 30D EK40J E40G US/CA model (1) (1) Part No. 68T Global model F8C FT8D F9.9J FT9.9L US/CA model F8A F9.9 T9.9 Part No. 63D Global model 40V 50H FT50C F50D US/CA model (1) (1) Part No. 6AH Global model F15C F20 F20C US/CA model F15A F20A Part No. 65W Global model F40H F50H FT50J F60F FT60G US/CA model F50 T50 F60 T60 Global model F70A F40G US/CA model F70A (1) (1) To be continued. 3-42

131 STEERING GUIDE ATTACHMENT KIT Part No. 6G Global model F20D F25D FT25F F30 F40F US/CA model F25A T25A F30A F40A Part No Global model 60F 70 75C 90A 75A US/CA model Global model 85A E60H US/CA model (1) (1) Part No Global model 55 US/CA model Part No. 6E Global model F75C F95A F100 US/CA model Global model US/CA model F115 F300 (V6) (1) (1) Part No. 67F Part No. 6EK Global model F75 F80 F90 F100D US/CA model F75A F90A Global model US/CA/ANZ model F115 F115 (1) (1) 3-43

132 TIE-AR KIT This kit is used to link the 2 engines in twin engine application. Adjustable distance: 600 mm (23.6 in) 800 mm (31.5 in) Part No. 6E Global model US/CA/ANZ model F30 F300 (V6) 3-44

133 CONVENTIONAL WIRE HARNESS An optional wire-harness for the remote control is available. This will help set up the remote control equipment on any boats. Choose a suitable wire-harness if necessary. For the wire color code description, see the table on page TO 10-PIN ADAPTER Part No. Length (L) Remarks A m (2 ft) r L W G P R Y Sb SWITCH PANEL HARNESS 7-PIN MAIN HARNESS P G R r L W Part No. Length (L) Remarks m (16 ft) Without PTT r P G L R W r G P R W L ENG (L) MAIN HARNESS EXTENSION 7-PIN EXTENSION HARNESS RC (L) 10-PIN MAIN HARNESS Part No. Length (L) Remarks A-50 5 m (16 ft) A-60 6 m (19 ft) A-70 7 m (23 ft) 6K1-8258A-40 8 m (26 ft) A m (32 ft) To S/W panel Part No. Length (L) Remarks m (7 ft) m (10 ft) r P G L R W W R G L P r Y Sb W L R G Lg P r (L) r G P R R R Sb Lg r r Y W L To S/W panel To 704/6X3 RC box (L) 10-PIN EXTENSION HARNESS Part No. Length (L) Remarks A-10 2 m (7 ft) A-30 3 m (10 ft) P Lg r G R L Y Sb W Y Sb W L R G P Lg r (L) 3-45

134 DIGITAL ELECTRONIC REMOTE CONTROL WIRE HARNESS MAIN WIRE HARNESS Used to connect between engine and remote control unit Part No. Length (L) Remarks 6X6-8258A-00 6 m (20 ft) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) For DEC unit 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) L W R W L W R R R W r R Y r R Y R W W R R W W R L W L W (L) DUAL STATION WIRE-HARNESS (3-4-6P) Used to connect between main RC and 2nd RC Ref. No. Part No. Length (L) Remarks 6X6-8258A-A1 5 m (16 ft) 1 6X6-8258A-C1 8 m (26 ft) For previous DEC unit 6X6-8258A-E1 12 m (38 ft) 6X6-8258A-G1 5 m (16 ft) 2 6X6-8258A-H1 8 m (26 ft) For new DEC unit 6X6-8258A-J1 12 m (38 ft) 1 (L) Y r X Y r X L L W W L L W W W R R W R R 2 (L) Y r r Y r r L L W W L L W W W R R W R R 3-46

135 DIGITAL ELECTRONIC REMOTE CONTROL WIRE HARNESS DUAL STATION WIRE-HARNESS (2-12P) Used to connect between main RC and 2nd RC Part No. Length (L) Remarks 6X6-8258A-1 5 m (16 ft) 6X6-8258A-D1 8 m (26 ft) For DEC unit 6X6-8258A-F1 12m (38 ft) (L) R Y 2nd RC Or R Y R Or R R R Main RC DUAL STATION WIRE-HARNESS (3-12P) Used to connect between main RC and 2nd RC (Quad engine special) Part No. Length (L) Remarks 6X6-8258A-R0 5 m (16 ft) 6X6-8258A-S0 8 m (26 ft) For new DEC unit 6X6-8258A-T0 12 m (38 ft) (L) Or R/Y W/L P P W/L X R/Y X X X Or X R R R R Or R/Y W/ S S W/ X R/Y X X X Or X R R R R CONVERSION HARNESS L Used to connect between new DEC unit and previous main switch. Part No. Length (L) Remarks 6X6-8258A-L0 150 mm (6 in) For new DEC unit (L) To DEC Y X X W P r X X R X X Y r P W X R X To SW panel 3-47

136 DIGITAL ELECTRONIC REMOTE CONTROL WIRE HARNESS CONVERSION HARNESS M Used to connect between 2nd helm new DEC and 2nd helm previous start/stop SW. (Single engine application) Part No. Length (L) Remarks 6X6-8258A-M0 200 mm (8 in) For 2nd station helm, Single engine application (L) To 2nd helm DEC Y P r W X X Y Wr X P To 2nd helm SW panel X X CONVERSION HARNESS N Used to connect between 2nd station helm new DEC and 2nd helm previous start/stop SW. (Twin engine application) Part No. Length (L) Remarks 6X6-8258A-N0 240 mm (9 in) For 2nd station helm, Twin engine application (L) X X P r P r Y Y P Y W r X P To 2nd helm DEC W X W X S Y W r X P To 2nd helm SW panel 3-48

137 DIGITAL ELECTRONIC REMOTE CONTROL WIRE HARNESS CONVERSION HARNESS P Used to connect between 2nd helm new DEC and 2nd helm previous start/stop SW. (Triple engine application) Part No. Length (L) Remarks 6X6-8258A-P0 240 mm (9 in) For 2nd station helm, Triple engine application (L) X X X P r Y P r Y P r Y P Y W r X P To 2nd helm DEC W W W S Y W r X P To 2nd helm SW panel C Y W r X P 3-49

138 MEMO

139 TILLER HANDLES 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE KIT (FOR US) TILLER HANDLE KIT CONTENTS WIRING DIAGRAM (FOR US) EXPLODED DIAGRAM (FOR US) MULTI-FUNCTION TILLER HANDLE KIT (FOR JAPAN) WIRING DIAGRAM (FOR JAPAN) EXPLODED DIAGRAM (FOR JAPAN) MULTI-FUNCTION TILLER HANDLE CONTENTS (FOR OTHERS) TILLER HANDLE GROMMET DESCRIPTION MULTI-FUNCTION TILLER HANDLE KIT (FOR EU & ANZ) HANDLE IMMOILIZER KIT CONTENTS WIRING DIAGRAM (FOR EU & ANZ) STEERING FRICTION CONTENTS

140 6X4 MULTI-FUNCTION TILLER HANDLE Yamaha prepares the various multi-function tiller handle kits for F30 to F115 and 40 to 90 engines. For US, the tiller handle kit for F25 is specially prepared. This handle has the electrical functions which are similar to those of 703 side mount remote control box. Engine IG switch, Emergency stop switch, PTT switch (top or side location), Neutral switch, Throttle friction adjuster, Shift lever, Throttle control grip, Variable troll RPM switch, LED warning indicators, and Warning buzzer are built into the handle. The 10-pin main harness in the handle will allow to easily connect the electrical system to the engine. MULTI-FUNCTION TILLER HANDLE KIT (FOR US) Two kinds of the size for handle extension bracket, four kinds of the length for 10-pin wire harness and some kinds of the length for control cables are prepared to install the handle according to the various engine specifications. The tiller handle kit (only one specification) is prepared for F40 to F115 and 50 to 90 engines. The fitting kit is prepared for each engine. Combine the tiller handle kit with the handle fitting kit depending on the applicable model, except F25. For installation procedure, see the instruction supplied with the kit. Tiller handle ASSY Setup manual Tiller handle kit (Common use for & F40-F115) Handle extension bracket Throttle cable Shift cable 10-pin main harness Steering friction ASSY Installation hardware Troll RPM switch Short shift lever Fitting kit for each model (Differs by model) 4-2

141 6X4 MULTI-FUNCTION TILLER HANDLE TILLER HANDLE KIT CONTENTS 50-90, F40-F115 KIT P/N:6X Part name Part No. Q ty Remarks Tiller handle ASSY 6X With PTT switch (Top), Requires fitting kit. Setup manual 6X4-2819K-15 1 English F25A (6P) KIT P/N:6X Part name Part No. Q ty Remarks Tiller handle ASSY 6X With PTT switch (Top) locknut M10 Steering friction ASSY 65W Setup manual 6X4-2819K-15 1 English 4-3

142 6X4 MULTI-FUNCTION TILLER HANDLE HANDLE FITTING KIT CONTENTS Select the fitting kit that matches the model. F115A KIT P/N:6X Part name Part No. Q ty Remarks Fuel pipe clamp 2 63D Cable clamp 1 63D Throttle cable 67G mm (35 in.) Pipe 1 67G Pipe 1 67G Nut 67G Shift cable 67G mm (40 in.) Grommet 2 68V Corrugated tube 6G mm (3.3 in.) Corrugated tube 6K mm (2.6 in.) Stay 6X Ext. bracket (Long) 6X D 1 92 mm (3.6 in.) Protector 6X pin main harness 6X mm (49 in.) Stud bolt olt M74 2 locknut locknut M10 Washer M01 2 Corrugated tube mm (9.1 in.) Clamp M42 1 Clamp M24 5 Clamp M30 1 Clip olt olt Friction plate 3 63D Friction piece 63D Steering lock knob 67G Steering lock shaft 67G Cover Friction plate 2 6X locknut M14 1 Washer M

143 6X4 MULTI-FUNCTION TILLER HANDLE HANDLE FITTING KIT CONTENTS F115 KIT P/N: 6X C0 Part name Part No. Q ty Remarks STR friction assy 67G Stud bolt Locknut M10 racket 6EK Shift cable 6EK mm (33.5 in) Clip Cable clamp 63D Throttle cable 6EK mm (29.1 in) Clamp M pin main harness 6X mm (37.4 in) Clamp M24 1 Troll RPM switch assy 6X

144 6X4 MULTI-FUNCTION TILLER HANDLE TILLER HANDLE KIT CONTENTS F75A, F90A KIT P/N:6X Part name Part No. Q ty Remarks Fuel pipe clamp 2 63D Cable clamp 1 63D Throttle cable 67G mm (35 in.) Pipe 1 67G Pipe 1 67G Nut 67G Shift cable 67G mm (40 in.) Grommet 2 68V Corrugated tube 6G mm (3.3 in.) Corrugated tube 6K mm (2.6 in.) Stay 6X Ext. bracket (Short) 6X D 1 45 mm (1.8 in.) Protector 6X Troll RPM switch ASSY 6X pin main harness 6X mm (49 in.) Stud bolt M10-70 mm olt M74 2 locknut locknut M10 Washer M01 2 Corrugated tube mm (9.1 in.) Clamp M42 1 Clamp M24 5 Clamp M30 1 Clip olt olt Friction plate 3 63D Friction piece 63D Steering lock knob 67G Steering lock shaft 67G Cover Friction plate 2 6X locknut M14 1 Washer M

145 6X4 MULTI-FUNCTION TILLER HANDLE TILLER HANDLE KIT CONTENTS F50, T50, F60, T60, F70A KIT P/N:6X Part name Part No. Q ty Remarks Cable clamp 1 63D Shift cable 67C mm (28 in.) Throttle cable 69W mm (24 in.) Troll RPM switch ASSY 6X pin main harness 6X mm (49 in.) olt M88 2 locknut M10 Clamp M42 1 Clamp M36 1 Clip Washer Friction piece 65W Friction plate 1 67C Steering lock knob 67C Steering lock shaft 67C Tilt lever cover Friction plate 3 6C locknut M14 1 Washer M5 1 Plate washer M56 1 Washer M26 1 Collar Collar Nut olt

146 6X4 MULTI-FUNCTION TILLER HANDLE TILLER HANDLE KIT CONTENTS F40A KIT P/N:6X Part name Part No. Q ty Remarks Cable clamp 1 63D Shift cable 67C mm (27 in.) Throttle cable 69W mm (24 in.) Troll RPM switch ASSY 6X pin main harness 6X mm (37 in.) olt M88 2 locknut M10 Clamp M42 1 Clamp M36 1 Clip Washer Friction piece 65W Friction plate 1 67C Friction plate 3 67C Steering lock knob 67C Steering lock shaft 67C Tilt lever cover locknut M14 1 Washer M5 1 Plate washer M56 1 Washer M26 1 Collar Collar Nut olt

147 6X4 MULTI-FUNCTION TILLER HANDLE TILLER HANDLE KIT CONTENTS 90 KIT P/N:6X Part name Part No. Q ty Remarks Cable clamp 63D Throttle cable 6H mm (24 in.) Shift cable 6H mm (29 in.) Ext. bracket (Short) 6X D 1 45 mm (1.8 in.) Shift handle 6X D 1 Shift lever 6X Screw Short type (exclusive), To replace original lever ush MA pin main harness 6X mm (26 in.) Stud bolt M10-70 mm Clamp M42 1 Clamp M11 1 Clamp M36 2 Clip olt Friction shaft Friction piece Rod Wing nut locknut Washer olt KIT P/N:6X Part name Part No. Q ty Remarks Throttle cable 6H mm (21 in.) Shift cable 6H mm (24 in.) Cable clamp 63D Grommet 2 6H Ext. bracket (Short) 6X D 1 45 mm (1.8 in.) 10-pin main harness 6X mm (24 in.) Stud bolt M10-70 mm locknut M10 Clamp M42 1 Clamp M36 1 Clip Friction shaft Friction piece Rod Wing nut locknut Washer olt

148 6X4 MULTI-FUNCTION TILLER HANDLE TILLER HANDLE KIT CONTENTS 50 KIT P/N:6X Part name Part No. Q ty Remarks Stay 63D Fuel pipe clamp 2 63D Throttle cable 63D mm (21 in.) Pipe 1 63D Nut 63D Shift cable 63D mm (24 in.) Clamp 63D Clamp 63D Grommet 1 6H pin main harness 6X mm (26 in.) Screw M00 1 M6-25 mm locknut M10 Washer M01 2 Collar M26 1 Clamp M42 1 Clamp M36 1 Clip olt olt olt Friction plate 2 63D Friction plate 3 63D Friction piece 63D Steering lock knob 63D Steering lock shaft 63D Cover locknut M

149 X4 MULTI-FUNCTION TILLER HANDLE WIRING DIAGRAM (FOR US) Tachometer 6Y5-8350T-90 TACH x100 r/min h set mode P Gy 6Y : 5 m (16 ft) Gy P P Gy G/R G G G/R G/R G/W R R R 6Y M0 : 2.5 m (8 ft) G G Y Y Y L Y L Y L Y L Stop SW Ignition SW PTT SW Troll RPM SW (*1) To ENGINE R Y G (*2) R R Y Y G W r Neutral SW Y W R G Lg G R Y Lg Sb Y Sb R G Lg r P uzzer Sb X W/L P r r W P W P r Y R Sb Lg R Sb Lg O/W Tiller handle assembly (*1) Depends on the engine specification. (*2) 1.5 m (5 ft) extension wire-harness (6Y5-8356N-00) is available. 1.5 m (5 ft) 4-11

150 6X4 MULTI-FUNCTION TILLER HANDLE EXPLODED DIAGRAM (FOR US) EX: F50/F60/F70A 4-12

151 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE KIT (FOR JAPAN) The tiller handle kit is prepared for F50 to F90. For installation procedure, see the instruction supplied with the kit. Troll RPM switch (Fuel injected F30- F90) LED indicators * Overheat warning * Oil warning PTT switch (Side) TILLER HANDLE KIT CONTENTS F80, F90 KIT P/N:6X Part name Part No. Q ty Remarks Fuel pipe clamp 2 63D Pipe 1 67G Nut 67G Grommet 2 68V Corrugated tube 6G mm (3.3 in.) Corrugated tube 6K mm (2.6 in.) Stay 6X Tiller handle ASSY 6X With PTT switch (Side), LED indicators Ext. bracket (Short) 6X D 1 45 mm (1.8 in.) Protector 6X Stud bolt olt M74 2 locknut locknut M10 Washer M01 2 Corrugated tube mm (9.1 in.) Clamp M24 5 Clamp M30 1 olt olt Friction plate 3 63D Friction piece 63D Steering lock knob 67G Steering lock shaft 67G Cover Friction plate 2 6X locknut M14 1 Washer M76 1 Setup manual 6X4-2819K-04 1 Japanese 4-13

152 6X4 MULTI-FUNCTION TILLER HANDLE TILLER HANDLE KIT CONTENTS F50H, FT50J, F60F, FT60G, F70A KIT P/N:6X Part name Part No. Q ty Remarks Grommet 2 6C Tiller handle ASSY 6X V5 1 With PTT switch (Side), LED indicators olt M-88 2 M10 locknut Clamp M36 1 Washer Friction piece 65W Friction plate 1 67C Steering lock knob 67C Steering lock shaft 67C Tilt lever cover Friction plate 3 6C locknut M14 1 Washer M5 1 Plate washer M56 1 Washer M26 1 Collar Collar Nut olt Setup manual 6X4-2819K-04 1 Japanese FT50C,F50D KIT P/N:6X Part name Part No. Q ty Remarks Grommet 2 62Y Tiller handle ASSY 6X With PTT switch (Side), LED indicators locknut M10 Clamp M36 1 Setup manual 6X4-2819K-04 1 Japanese 4-14

153 6X4 MULTI-FUNCTION TILLER HANDLE WIRING DIAGRAM (FOR JAPAN) Warning indicators Stop SW Ignition SW PTT SW Troll RPM SW (*1) P Gy Gy P X X W G/R G G G/R P/W P/ r Neutral SW To ENGINE Y W Sb X W/L R G Lg P r G R Y Lg Sb W r P Y Sb W P R r X Lg Y Y r P Y R Sb Lg R Sb Lg uzzer O/W (*1) Depends on the engine specification. Tiller handle assembly 4-15

154 6X4 MULTI-FUNCTION TILLER HANDLE EXPLODED DIAGRAM (FOR JAPAN) EX: F50H/F60F/F70A 4-16

155 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE CONTENTS (FOR OTHERS) The tiller handle kit is not prepared for other market, except some region. Regarding the tiller handle component parts information, see the applicable years model parts catalog. Troll RPM switch (Depends on the engine specification.) LED indicators * Overheat warning * Oil warning PTT switch (Top) TILLER HANDLE GROMMET DESCRIPTION Warning indicator lead 10-pin main harness Troll RPM switch Throttle cable Shift cable Immobilizer harness 4-17

156 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE KIT (FOR EU & ANZ) oth tiller handle kit and fitting kit are required for installation. TILLER HANDLE KIT CONTENTS F30 F115 KIT P/N:6X Part name Part No. Q ty Remarks Tiller handle ASSY 6C w/o Troll RPM SW. Requires fitting kit. Setup manual 6X4-2819K-K7 1 English, French, Spanish HANDLE FITTING KIT CONTENTS F30 F40 KIT P/N: 6X Part name Part No. Q ty Remarks Cable clamp 1 63D Shift cable 67C Throttle cable 69W Cap 6X For PTT SW Troll rpm SW ASSY 6X Wire harness 6X Wire lead 6X L=700 mm (27.6 in.) olt M88 2 locknut M10 Clamp M42 1 Clamp M36 1 Clip Washer Friction piece 65W Friction plate 1 67C Friction plate 3 67C Steering lock knob 67C Steering lock shaft 67C Tilt lever cover locknut M14 1 Washer M5 1 Plate washer M56 1 Washer M26 1 Collar Collar Nut olt

157 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE KIT (FOR EU & ANZ) F50 F70 KIT P/N: 6X Part name Part No. Q ty Remarks Cable clamp 1 63D Shift cable 67C Throttle cable 69W Cap 6X For PTT SW Troll rpm SW ASSY 6X Wire harness 6X Wire lead 6X L=700 mm (27.6 in.) olt M88 2 locknut M10 Clamp M42 1 Clamp M36 1 Clip Washer Friction piece 65W Friction plate 1 67C Steering lock knob 67C Steering lock shaft 67C Tilt lever cover Friction plate 3 6C locknut M14 1 Washer M5 1 Plate washer M56 1 Washer M26 1 Collar Collar Nut olt

158 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE KIT (FOR EU & ANZ) HANDLE FITTING KIT CONTENTS F80 F100 KIT P/N: 6X A1 Part name Part No. Q ty Remarks Fuel pipe clamp 2 63D Cable clamp 1 63D Throttle cable 67G Pipe 1 67G Pipe 1 67G NUT 67G Shift cable 67G Grommet 2 68V Corrugated tube 6G mm (3.3 in.) Corrugated tube 6K mm (2.6 in.) Stay 6X racket 6X D 1 45 mm (short) Protector 6X Troll rpm SW ASSY 6X Wire harness 6X mm (49.2 in.) Wire lead 6X L=1250 mm (49.2 in.) Stud bolt olt M74 2 locknut locknut M10 Washer M01 2 Corrugated tube mm (9.1 in.) Clamp M42 1 Clamp M24 5 Clamp M30 1 Clip olt olt Friction plate 3 63D Friction piece 63D Steering lock knob 67G Steering lock shaft 67G Cover Friction plate 2 6X locknut M14 1 Washer M

159 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE KIT (FOR EU & ANZ) F115A KIT P/N: 6X Part name Part No. Q ty Remarks Fuel pipe clamp 2 63D Cable clamp 1 63D Throttle cable 67G Pipe 1 67G Pipe 1 67G Nut 67G Shift cable 67G Grommet 2 68V Corrugated tube 6G mm (3.3 in.) Corrugated tube 6K mm (2.6 in.) Stay 6X racket 6X D 1 92 mm (Long) Protector 6X Wire harness 6X mm (49.2 in.) Wire lead 6X L=1250 mm (49.2 in.) Stud bolt olt M74 2 locknut locknut M10 Washer M01 2 Corrugated tube mm (9.1 in.) Clamp M42 1 Clamp M24 5 Clamp M30 1 Clip olt olt Friction plate 3 63D Friction piece 63D Steering lock knob 67G Steering lock shaft 67G Cover Friction plate 2 6X locknut M14 1 Washer M

160 6X4 MULTI-FUNCTION TILLER HANDLE MULTI-FUNCTION TILLER HANDLE KIT (FOR EU & ANZ) F115 KIT P/N: 6X C0 Part name Part No. Q ty Remarks STR friction assy 67G Stud bolt Locknut M10 racket 6EK Shift cable 6EK mm (33.5 in) Clip Cable clamp 63D Throttle cable 6EK mm (29.1 in) Clamp M pin main harness 6X mm (37.4 in) Clamp M24 1 Troll RPM switch assy 6X HANDLE IMMOILIZER KIT CONTENTS F30 F115 KIT P/N: 6Y8-W0035-C0 Part name Part No. Q ty Remarks Wire-harness 6Y M m (8 ft) Single hub 6Y Wire-lead 6Y For system PWR Pigtail bus wire 6Y m (12 ft) Main bus wire 6Y m (1 ft) * Requires to replace the rigging grommet as follows. F50 up to F60: 6C F75 up to F115 (68V): 68V

161 6X4 MULTI-FUNCTION TILLER HANDLE WIRING DIAGRAM (FOR EU & ANZ) AFTER JAN R Pigtail bus wire Hub Main bus wire Hub Pigtail bus wire w/ power lead 6Y R X R X R X X Y Y Immobilizer unit L W L W X L W X L W L W L W W L R R Y Y Y Y Y L R L G R Warning indicators Stop SW Ignition SW PTT SW Troll RPM SW To ENGINE P G/R Gy G Gy G P G/R X P/W X P/ G G Y R Y Y R R W r Neutral SW Y W R G Lg G R Y Lg Sb Y Sb R G Lg r P uzzer Sb X W/L P r rp W P W P r Y Y Y R Sb Lg R Sb Lg O/W Tiller handle assembly UP TO DEC ECM Lg YDIS coupler R Sb Hub Ignition SW Hub Pigtail bus wire w/ power lead 6Y m(15 ft) Main bus wire 0.3 m (1 ft) Pigtail bus wire 0.3 m (1 ft) Immobilizer unit w/ EXT wire-harness 3.7 m (12 ft) 4-23

162 STEERING FRICTION CONTENTS For detailed installation information, see the instruction manual packed in the tiller handle kit and/or the steering friction kit. General torque table Nm kgf m lb ft M10 locknut M6 bolt M5 bolt Part No. 6AH (for manual tilt) 6AH (for power tilt) Global model F9.9H F15C F20 F20C US/CA model F15A F20A Part No. 67C Global model F30 F40F US/CA model F30A F40A Part No. 65W Global model F25D FT25F US/CA model F25A/ T25A Part No. 68T Global model F8C FT8D US/CA model F8A 3 Nm, 0.3 kgf m, 2.2 lb ft To be continued. 4-24

163 STEERING FRICTION CONTENTS Part No. 63D Global model 40V 50H FT50C F50D US/CA model Part No. 6C Global model F40H F50H FT50J F60F FT60G US/CA model F50 T50 F60 T60 18 Nm, 1.8 kgf m, 13 lb ft 20 Nm, 2.0 kgf m, 15 lb ft Part No. 67G Global model F75 F80 F90 F100D F75C US/CA model F75A F90A Global model F95A F100 F/FL115A US/CA model F/LF115A Global model F/FL115 US/CA/ANZ model F/LF115 Part No Global model 60F 70 75C 90A US/CA model Part No. 6E Global model E115A US/CA model 20 Nm, 2.0 kgf m, 15 lb ft 18 Nm, 1.8 kgf m, 13 lb ft Use this hole for F115A, F100, F95A, and F75C 18 Nm, 1.8 kgf m, 13 lb ft 1/4 turns out from seated position 4-25

164 MEMO

165 CONVENTIONAL GAUGE (6Y5 & 6Y7) MOUNTING THE METERS METER MOUNTING PROCEDURE ANALOG GAUGE ILLUMINATION (6Y7 TYPE) ANALOG TACHOMETER ANALOG TACHOMETER APPLICATIONS ANALOG TACHOMETER DIMENSIONS POLE NUMER SET UP DIGITAL TACHOMETER DIGITAL TACHOMETER APPLICATIONS DIGITAL TACHOMETER DIMENSIONS POLE NUMER SET UP SPEEDOMETER SPEEDOMETER TYPES AND APPLICATIONS SPEEDOMETER DIMENSIONS WATER PRESSURE DAMPER (OP) SPEEDOMETER TUE ROUTING DIGITAL SPEEDOMETER SET UP FUEL MANAGEMENT GAUGE FUEL MANAGEMENT GAUGE TYPES AND APPLICATIONS FUEL MANAGEMENT GAUGE DIMENSIONS FUEL SENSOR INSTALLATION WIRING DESCRIPTION FUEL MANAGEMENT GAUGE SET UP FUEL MGT GAUGE WITH SPEEDOMETER SET UP ANALOG TRIM METER ANALOG TRIM METER APPLICATIONS ANALOG TRIM METER DIMENSIONS TRIM SENSOR ADJUSTMENT COOLANT PRESSURE METER COOLANT PRESSURE METER APPLICATIONS COOLANT PRESSURE METER DIMENSIONS COOLANT PRESS. ATTACHMENT INSTALLATION To be continued. 5-1

166 CONVENTIONAL GAUGE (6Y5 & 6Y7) COOLANT TEMP. METER COOLANT TEMP. METER TYPES AND APPLICATIONS COOLANT TEMP. METER DIMENSIONS COOLANT PRESS. ATTACHMENT AND/OR COOLANT TEMP. SENSOR INSTALLATION (FOR 2-STROKE MODELS) ROUTING COOLANT TEMP. LEAD ROUTING THE COOLANT PRESS. TUE COOLANT TEMP. SENSOR AND/OR COOLANT PRESS. ATTACHMENT INSTALLATION (FOR 4-STROKE MODELS) ROUTING THE COOLANT TEMP. LEAD & COOLANT PRESS. TUE SENSOR/ATTACHMENT INSTALLATION AND ROUTING HOUR METER HOUR METER APPLICATIONS HOUR METER DIMENSIONS WIRING THE MECHANICAL HOUR METER WIRING THE DIGITAL HOUR METER VOLTAGE METER VOLTAGE METER TYPES AND APPLICATIONS VOLTAGE METER DIMENSIONS WIRING THE VOLTAGE METER FUEL METER FUEL METER TYPES AND APPLICATIONS FUEL METER DIMENSIONS WIRING THE FUEL METER CHARGE WARNING UNIT CHARGE WARNING UNIT TYPES AND APPLICATIONS WIRING THE CHARGE WARNING UNIT To be continued. 5-2

167 CONVENTIONAL GAUGE (6Y5 & 6Y7) WIRE HARNESSES REMOTE-OIL TANK HARNESS ADDITIONAL ACCESSORY LEAD METER HARNESS LAMP SWITCH TRIM METER LEAD TRIM AND OIL LEAD COMINATION TRIM AND OIL LEAD CONVERSION HARNESS FUEL MANAGEMENT GAUGE HARNESS LIGHTING COIL EXTENSION HARNESS RECTIFIER KIT WIRING DIAGRAMS WIRE COLOR CODE DIGITAL METER (6Y5) ANALOG METER (6Y7) INTERCHANGEAILITY ETWEEN TACHOMETER AND ENGINE (up to 2006 and after 2007) RIGGING GROMMET DESCRIPTION

168 MOUNTING THE METERS The meters can be installed to electrical start models because power source is required for the operation. METER MOUNTING PROCEDURE Follow the procedures below for mounting the gauges. 1. Select a mounting location so that the meter is easy to read from the operating position. e sure that there is sufficient clearance behind the panel for the meter. For analog meters, be sure that the angle for mounting the meter is 65 to 90 degrees. If the analog gauge is mounted onto horizontal surface, the pointer may not return to the zero position after the engine has stopped. 2. Make a hole at the desired position. 3. Remove the fitting plate from the meter, fit the meter into the panel, and install the fitting plate over the mounting studs. 4. Place the washers over the studs, and then evenly tighten the mounting nuts until the meter can no longer be rotated by hand. 5. Connect the wire-harnesses to the gauges, and secure them into a boat [Analog meter] Gasket Fitting plate Panel thickness Wave washer Nut Mounting stud Cutting area (for thicker panel) * If the gauge is mounted onto a 13 mm (0.5 in) or thicker board, cut out the fitting plate end so that the mount nut is enough tightened. ANALOG GAUGE ILLUMINATION (6Y7 TYPE) For black-face analog gauge, the faceplate is illuminated with permeation light for nighttime operation. The white-face analog gauge used an indirect clear lighting. 5-4

169 ANALOG TACHOMETER A tachometer is essential for proper outboard performance. The engine speed can be monitored to obtain most efficient operation. In twin engine applications, the tachometers can be used to set the throttle of each engine accurately ANALOG TACHOMETER APPLICATIONS Ref. No. Description Part No. Applicable model Without indicators LK panel Without indicators WHT panel With 3 oil indicators LK panel With 3 oil indicators WHT panel With overheat & oil indicators LK panel With overheat & oil indicators WHT panel 6Y Y Y Y Pre-mixed FT8 (T8), F9.9 F25 (FT/T25) 250G, L250G 6Y Above 40 (3-cyl) w/ oil injection (except 250G/ L250G) 6Y Above F30 [Mechanical RC] * Tachometer with triple oil indicators (Ref. No.2) requires the relay to light the indicators. See the wiring diagram to connect the relay (P/N: 6Y ). * If the current tachometer does not fit the older engine, use the wire harness adapter which is shown in page

170 ANALOG TACHOMETER ANALOG TACHOMETER DIMENSIONS 3-indicator for 250G & L250G 200 (7.87) 200 (7.87) mm (in.) 2-indicator for 4-stroke and oil injected 2-stroke engines (except 250G & L250G) mm (in.) 200 (7.87) 200 (7.87) 93 (3.66) 84.5 (3.33) 93 (3.66) 84.5 (3.33) 11.2 (0.44) 65 (2.56) 28.9 (1.14) Y R G 210 (8.27) 11.2 (0.44) 65 (2.56) 28.9 (1.14) Y P R r X 210 (8.27) P POLE NUMER SET UP Yamaha tachometer shows the engine RPM by receiving the pulse signal from lighting coil. The flywheel magneto used on Yamaha outboard motors varies in number of poles used: 4-pole, 6- pole and 12-pole. It is necessary to adjust the calibration switch on the back of gauge to correspond to the particular motor being used. The initial setting is 12-pole. Adjust if necessary. Description Applicable model 4-pole 6 15, 55, E/40G, E40J, E48C, E55C, EK40G, EK40J 6-pole 20D, 25N, 30D, 40V, 50H, 60F 70, E/25, EK25, E/30H, E/40X, E60H, F8C (F8A), FT8D, F9.9J (F9.9) 12-pole 55D, 75A, 75C, 85A, 90A, V4, V6, E75, F15 (6AG) F250 (*1) (*1) Mechanical RC POLE NUMER ADJUSTMENT 1. Remove the rubber grommet (1) from the back of meter. 2. Turn the rotating switch (2) with a slotted-head screwdriver to the required position. 3. Reinstall the grommet. 5-6

171 DIGITAL TACHOMETER A tachometer is essential for proper outboard performance. The engine speed can be monitored to obtain most efficient operation. In twin engine applications, the tachometers can be used to set the throttle of each engine accurately. The digital tachometer includes the elapsed hour meter, the trim meter and the oil warning indicator. Also, this meter can be used for both 2 and 4 stroke models by switching the settings. 1 2 TACH 5 TACH 5 x100 r/min h x100 r/min h set mode set mode DIGITAL TACHOMETER APPLICATIONS Ref. No. Description Part No. Applicable model 1 Multifunction 6Y5-8350T G,L250G 2 Multifunction w/o Check engine and Water in fuel indicators 6Y5-8350T-91 Above 40 (3-cyl) w/ oil injection & PTT (except 250G/L250G), Above F30 w/ PTT (*1) (*1) Mechanical RC * If the current tachometer does not fit the older engine, use the wire-harness adapter which is shown on page DIGITAL TACHOMETER DIMENSIONS 1. With twin 4-pin couplers (No.1) 2. With single 4-pin coupler (No.2) mm (in.) mm (in.) 97 (3.82) 84.5 (3.33) 210 (8.27) 97 (3.82) 84.5 (3.33) P Gy G R G W 65.5 (2.58) 8.5 (0.33) 25 (0.98) W L R W G G R W W Or Gy P 65.5 (2.58) 8.5 (0.33) 25 (0.98) 190 (7.48) 210 (8.27) 5-7

172 DIGITAL TACHOMETER POLE NUMER SET UP The tachometer indicates the engine speed by receiving the pulses from the lighting coil. The flywheel magnets used in Yamaha outboards vary in number of poles used: 6-pole and 12-pole. It is necessary to change the calibration switch on the back of the meter to correspond to the particular motor being used. Also, the selection of the engine type and the trim sensor type is required. Description 6-pole 12-pole Applicable model 40V, 50H, 60F, 70 75C, 90A, V4, V6, F30 F250 [Mechanical RC] POLE NUMER ADJUSTMENT 1. Remove the rubber grommet from the back of the meter. 2. Set the toggle dipswitches in the chart as shown. 3. Reinstall the grommet. ON OFF SW.1 SW.2 SW.3 No. SW.1 SW.2 SW.3 Dipswitch function Trim sensor type Generator type Engine type ON 2 lead 6-pole 4-stroke OFF 3 lead 12-pole 2-stroke * The switch position in the illustration shows the initial setting. 5-8

173 SPEEDOMETER The speedometer indicates an approximate speed of the boat through the water by measuring the impact force of the water with a pressure gauge. This impact force will vary with the density of the water and the speed of the impact. The density can vary by the purity of the water and the temperature of water. The speed of water impact can vary by the location of the speed sensor and its relation to the water flow off the area of the boat in front of the sensor. ecause of these variables, the true speed of a boat can vary from the indicated speed on the meter. Especially, the digital speedometer uses LCD readouts for speed, clock, trip distance, fuel tank level, and warning information for low fuel level and abnormal battery voltage. The speed can be calibrated for mph, km/h, and knots SPEED km/h knot mph km mile TRIP TIME ATT set mode SPEEDOMETER TYPES AND APPLICATIONS Ref. No. Description Part No. Applicable model Above 40 (3-cyl) 6Y S6 1 Digital multifunction Above F30 [Mechanical RC] 6Y For Yamaha manufactured boats (Japan) 2 Analog, LK panel 0 75 mph ( km/h) 6Y Analog, WHT panel 0 75 mph ( km/h) 6Y Analog, LK panel 6Y mph (20 80 km/h) Analog, WHT panel 6Y mph (20 80 km/h) Above 40 (3-cyl) 4 Analog, LK panel Above F30 [Mechanical RC] 6Y km/h (15 65 knot) Analog, WHT panel 6Y km/h (15 65 knot) 5 Analog, LK panel 0 80 km/h (10 43 knot) 6Y Analog, WHT panel 0 80 km/h (10 43 knot) 6Y

174 SPEEDOMETER SPEEDOMETER DIMENSIONS Digital 25 (0.98) Analog mm (in.) 97 (3.82) 84.5 (3.33) 93 (3.66) 84.5 (3.33) 8.5 (0.33) 65.5 (2.59) 210 (8.27) R Y L W 11.2 (0.44) 52 (2.05) 41.9 (1.65) * A 6 m (19 ft) water tube (P/N: ) is included in all speedometer units (except digital speedometer unit P/N: 6Y S6). WATER PRESSURE DAMPER (OP) Installing the water pressure damper between the gauge and water tube is recommended under following condition. To reduce a risk if water has leaked at connector end causing the gauge damage. The pointer of analog gauge is wiggled if water pressure pulsates. Clamp M10 Water Tube 6Y Water Pressure Damper 6Y

175 SPEEDOMETER SPEEDOMETER TUE ROUTING 1. Cut off about 3 mm (0.12 in.) from the end of the nipple of the speedometer tube to open it. DIGITAL SPEEDOMETER SET UP 1. Remove the rubber grommet from the back of the meter. 2. Set the toggle dipswitches in the chart as below. 3. Reinstall the grommet. Cut off 3 mm (0.12 in.) 2. Route the speedometer tube carefully to avoid crimping or damage. SW.1 ON OFF OFF SW.2 ON ON OFF Display km/h mph knot/h 3. Connect the tube to the nipple. * The optional speed sensor (P/N: ) is required if the speedometer tube is not equipped to the clamp bracket area. * In high-performance applications where the engine has been mounted in an elevated position, it may be necessary to use the optional speed sensor to obtain a correct reading. SW.3 ON OFF OFF SW.4 ON ON OFF Yamaha AYC Fuel Europe original (US) sensor Ω Ω Ω * The switch position in the illustration shows the initial setting, which is the mph display and AYC fuel sensor. (1) Optional speed sensor 5-11

176 FUEL MANAGEMENT GAUGE The fuel management gauge has the functions as a fuel flow gauge, fuel consumption gauge, fuel economy gauge, twin engine RPM synchronizer for dual installations, and an optional water separator warning indicator that detects water in the fuel filter. The gauge can display by receiving data from the fuel flow sensor and either an NMEA 0183 compatible GPS unit or the digital speedometer. * Fuel management gauge with speedometer does not have the function as twin engine RPM synchronizer, water detection warning, and each engine s fuel measurement. 1 2 FUEL MANAGEMENT P S TTL ECON SYNC l/h gph km/l mpg TRIP FLOW ECOM TTL SPEED CPS FUEL km/h knots mph mile V mpgph km/l/h AT set mode set mode FUEL MANAGEMENT GAUGE TYPES AND APPLICATIONS Ref. No. Description Part No. Applicable model Fuel mgt gauge kit 1 6Y5-W For single-engine 1 Fuel mgt gauge kit 2 6Y5-W For twin-engine 2 Fuel mgt gauge with speedometer 6Y Above 115 Above F115 [Mechanical RC] FUEL MGT GAUGE KIT CONTENTS Description Part No. Q ty Kit 1 Kit 2 Remarks Fuel mgt gauge 6Y5-8350F w/ 3-prong connector EXT wire-harness 6Y F m (26 ft) Fuel flow sensor 6Y EXT wire-lead 6Y cm (1 ft) (LK) Screw Wire-lead cm (2.3 ft) (LK) Installation manual 6Y5-2819K-F0 1 1 ADDITIONAL PARTS REQUIREMENTS (FOR FUEL MGT w/ speedometer) Description Part No. Q ty Remarks Fuel flow sensor 6Y EXT wire-harness 6Y F1 1 8 m (26 ft) Screw OPTIONAL WIRE-HARNESS Description Part No. Remarks GPS signal lead 6Y F0 To connect an NMEA0183 compatible GPS unit 5-12

177 FUEL MANAGEMENT GAUGE FUEL MANAGEMENT GAUGE DIMENSIONS Fuel management gauge (Ref. No. 1) mm (in.) 97 (3.82) 65.5 (2.58) 8.5 (0.33) 25 (0.98) Pu Or W/R 210 (8.27) Or R Y L G G/W Pu/W R X 84.5 (3.33) 310 (12.2) W Fuel mgt gauge with speedometer (Ref. No. 2) mm (in.) 97 (3.82) 16.9 (0.66) 65.5 (2.58) Pu Or 210 (8.27) Or R Y L W X X 84.5 (3.33) 310 (12.2) 8.5 (0.33) 25 (0.98) Pu/W W X 5-13

178 FUEL MANAGEMENT GAUGE FUEL SENSOR INSTALLATION Follow the notifications below. 1. Locate the sensor in a well ventilated area in boat between the engine and a water separator. 2. Place the sensor with the UP mark facing upward. 3. Use a fuel joint that is fitted to the fuel hose of the outboard motor. 4. Secure all fuel hose ends with a hose clamp with good anti-corrosion performance. * For twin engine application, refer to Wiring diagram in this chapter. See the installation manual in the package for further information. ( ) Or (+) Nipple1/4-18NPT (Market obtainable) To extension wire lead Pu (S) Water separator (Market obtainable) Clamp Fuel flow sensor Primer bulb Fuel valve IN OUT IN UP OUT Fuel tank Clamp Inboard area To extension wire lead if water detection switch is incorporated. 5-14

179 FUEL MANAGEMENT GAUGE WIRING DESCRIPTION Fuel management gauge e sure that both the fuel management gauge and speedometer yellow wires are connected to the same power source and activated at the same time. Pu Or W/R A Or R Y L G G/W Pu/W R W X R: 12 volt G: To the green wire from STD digital tachometer G/W: To the green wire from PORT digital tachometer for twin motor installations : To the ground L: To light switch Y: To digital speedometer to the same power source Coupler A : To the extension wire lead for the fuel flow sensor Coupler : To the digital speedometer or an NMEA 0183 compatible GPS unit Fuel management gauge with speedometer The speed data is automatically picked up, therefore wiring to the speedometer is not needed. Pu Or Or R Y L W X X R: 12 volt W:To fuel level sensor (Fuel tank) : To the ground L: To light switch Y: To power source Coupler A : To the extension wire lead for the fuel flow sensor Coupler C : To an NMEA 0183 compatible GPS unit A Pu/W W C X 5-15

180 set mode FUEL MANAGEMENT GAUGE CONNECTING TO THE DIGITAL SPEEDOMETER (FOR FUEL MANAGEMENT GAUGE) This calculates the fuel economy and fuel consumption, inputting the speed data to the fuel management gauge from the digital speedometer. 1. Remove the black grommet in the back of the digital speedometer. 2. Install the 3-prong connector (P/N: 6Y S0) to the digital speedometer. 3. Connect the 3-prong connector to the fuel management gauge. CONNECTING SPEEDOMETER TUE (FOR FUEL MGT GAUGE WITH SPEEDOMETER) See the speedometer section. CONNECTING TO A GPS This is to input the speed data to the fuel management gauge (with speedometer) from a GPS unit. 1. Connect the optional signal lead (P/N: 6Y F0) to an NMEA 0183 compatible GPS unit. 2. Connect the signal lead to the fuel management gauge. 3. Connect the ground lead for GPS and fuel management gauge (with speedometer) to the same ground. (2) R W Signal Lead for Speedometer (1) (1) Grommet (2) 3-prong connector 6Y S0 W (+) Signal Lead for GPS Optional: 6Y F0 SPEED YAMAHA km/h knot mph km mile TRIP TIME ATT YAMAHA set mode Speedometer FUEL MANAGEMENT P S TTL ECON SYNC set mode l/h gph km/l mpg Coupler GPS NMEA0183 Fuel management gauge If the speed signal is input from a GPS, the speed pressure tube is not required. Signal Lead for GPS W (+) Optional: 6Y F0 TRIP FLOW ECOM TTL SPEED FUEL CPS km/h knots mph mile V mpgph km/l/h AT Coupler C GPS NMEA0183 Fuel mgt gauge with speedometer 5-16

181 FUEL MANAGEMENT GAUGE FUEL MANAGEMENT GAUGE SET UP 1. Remove the grommet (1) on the back of the gauge. 2. Select the fuel measurement switch 4 for either gallons per hour (gph) or liters per hour (L/h). 3. Select the signal input switch 5 and 6 for either the digital speedometer or a GPS. 4. Set the compensator switch 1, 2 and 3 if there is a difference of fuel consumption between the actual amount and meter reading. For example: Actual amount of fuel used: 50 gallons Fuel management gauge indicates: 51 gallons Different = + 1 gallon 1 gallon / 50 gallons = 0.02 or 2% SW.1 ON OFF ON OFF ON OFF ON OFF SW.2 ON ON OFF OFF ON ON OFF OFF SW.3 ON ON ON ON OFF OFF OFF OFF Compensation 4% 3% 2% 1% 0 +1% +2% +3% SW.4 OFF ON Unit L/h gph SW.5 OFF ON SW.6 ON OFF Input source Speedometer GPS FUEL MGT GAUGE WITH SPEEDOMETER SET UP (1) For 6 line switches (1), see the above instruction. Switch 6 is not used. For 4 line switches (2), see DIGITAL SPEEDOMETER SET UP on page (2) 5-17

182 ANALOG TRIM METER The trim meter shows the trim angle of the outboard motor. 1 2 ANALOG TRIM METER APPLICATIONS Ref. No. Description Part No. Applicable model pin coupler LK panel ullet connector LK panel 4-pin coupler WHT panel ullet connector WHT panel 6Y Y Y Y Above premixed 40 (3-cyl) w/ PTT, 250G/ L250G Above 40 (3-cyl) w/ oil injection & PTT (except 250G/L250G), Above F30 w/ PTT (*1), T25 (*2) Using as a set with tachometer, 6Y Premixed 40 (3-cyl)-225 w/ PTT, 250G/L250G Above 40 (3-cyl) w/ oil injection & PTT (except 250G/L250G), Above F30 w/ PTT (*1), T25 (*2) Using as a set with tachometer, 6Y (*1) Mechanical RC (*2) T25 for US/CA ANALOG TRIM METER DIMENSIONS With 4-pin coupler mm (in.) 200 (7.87) 200 (7.87) With bullet connector 300 (11.8) 200 (7.87) 200 (7.87) mm (in.) 60 (2.36) 46.6 (1.83) 11 (0.43) 13.7 (0.54) 52 (2.05) Y L x x P 60 (2.36) 46.6 (1.83) 11 (0.43) 13.7 (0.54) 52 (2.05) Y L P TRIM SENSOR ADJUSTMENT For a down position adjustment, loosen the trim sensor screw and make an adjustment so that the needle aligns with the marking line indicating DOWN. 5-18

183 COOLANT PRESSURE METER The coolant pressure meter shows the water pressure of cooling water passage, and provides a warning for the operator when there is a problem with the cooling system. * For all in-line cylinder models, the position for installing the sensor shares the coolant temperature output. Therefore, either the coolant temperature meter or the coolant pressure meter can be used for one engine. * However, on V4, V6, and F150 models, both meters can be used for one engine. 1 2 COOLANT PRESSURE METER APPLICATIONS Ref. No. Description Part No. Applicable model 1 kpa, lack panel 6Y kpa, White panel 6Y Above 40 [3-cyl] 2 psi, lack panel 6Y Above F25 (FT/T25) [Mechanical RC] psi, White panel 6Y ADDITIONAL PARTS REQUIREMENTS Description Part No. Remarks Coolant pressure attachment With 10 m (32 ft) tube COOLANT PRESSURE METER DIMENSIONS mm (in.) 60 (2.36) 52 (2.05) 42 (1.65) 11 (0.43) 18.9 (0.74) COOLANT PRESS. ATTACHMENT INSTALLATION The method for installing the coolant pressure attachment is the same as the coolant temperature sensor. See the installation instruction to the sensor in the coolant temperature meter on page To meter M14 X

184 COOLANT TEMP. METER The coolant temperature meter uses a sensor on the engine unit to indicate the temperature of the cooling water inside the powerhead. The meter has a red zone to indicate overheating so problems can be corrected before severe damage occurs. * For all in-line cylinder models, the position for installing the sensor shares the coolant pressure output. Therefore, either the coolant temperature meter or the coolant pressure meter can be used for one engine. * However, on V4, V6, F150, and F200 (L4) models, both meters can be used for one engine. 1 2 COOLANT TEMP. METER TYPES AND APPLICATIONS Ref. No. Description Part No. Applicable model 1 lack panel 6Y Above 40 [3-cylinder] 2 White panel 6Y Above F25 (FT/T25) [Mechanical RC] ADDITIONAL PARTS REQUIREMENTS Description Part No. Remarks Coolant temp. sensor With 7 m (23 ft) leads M14 X 1.5 Sb COOLANT TEMP. METER DIMENSIONS mm (in.) 60 (2.36) 52 (2.05) 46.6 (1.83) 11 (0.43) (0.54) 5-20

185 COOLANT TEMP. METER COOLANT PRESS. ATTACHMENT AND/OR COOLANT TEMP. SENSOR INSTALLATION (FOR 2-STROKE MODELS) Remove the screw plug (1) from the cylinder 75C, 90A, 75A, 85A head and install the sensor/attachment (2) with a new gasket. After installing the sensor/attachment, check for water leakage. Tightening torque N m kgf m ft lb Sensor/attachment (M14) (1) (2) 40V, 50H V4, V6 (2) Coolant temp. sensor (2) (1) (1) (2) Coolant press. attachment (1) E48C, 55 (1) (2) NOTICE Install the coolant pressure attachment on the port side. If it is installed on the starboard side, the tube could cause damage by hard bending. 60F, 70 (1) (2) 5-21

186 COOLANT TEMP. METER ROUTING COOLANT TEMP. LEAD V4 V6 (2.6) Same height as oil tank Add a clamp to oil tank mount bolt to secure tube Through the stopper base Secure with 10-pin harness holder Secure with cable holder Along port-side bottom cowling Through the stopper base V6 (2.6) V6 (3.1) Same height as thermostat cover Through the fuel pump stopper base Through the fuel filter base Through the stopper base Secure with 10-pin harness holder Secure with clamp ROUTING THE COOLANT PRESS. TUE V4 Same height as oil tank Secure with cable holder Secure with fuel hose clamp Add a clamp to oil tank mount bolt to secure tube Secure with cable holder Along port-side bottom cowling 5-22

187 COOLANT TEMP. METER COOLANT TEMP. SENSOR AND/OR COOLANT PRESS. ATTACHMENT INSTALLATION (FOR 4-STROKE MODELS) F25D (F25A), FT25F (T25A), F30 (F30A), F40F (F40A) F95A, F100, F115A Coolant temp. sensor, or coolant pressure attachment F40H, F50H (F50), FT50J (T50), F60F (F60), FT60G (T60), F70A (F70A), F40G Only one of the coolant press. attachment or coolant temp. sensor can be installed, even if the engine has two points for installation. Coolant temp. sensor Coolant pressure attachment FT50C, F50D Coolant pressure attachment Coolant temp. sensor Coolant temp. sensor, or coolant pressure attachment 5-23

188 COOLANT TEMP. METER COOLANT TEMP. SENSOR AND/OR COOLANT PRESS. ATTACHMENT INSTALLATION (FOR 4-STROKE MODELS) F115 Only one of the coolant press, attachment or coolant temp. sensor can be installed. F75 (F75A), F80, F90 (F90A), F100D, F75C Remove the negative battery cable and oil dipstick, then put a rag on the oil filler hole to prevent dust etc. from falling into the oil sump. Coolant temp. sensor Coolant temp. sensor, or coolant pressure attachment Coolant press. attachment 5-24

189 COOLANT TEMP. METER COOLANT TEMP. SENSOR AND/OR COOLANT PRESS. ATTACHMENT INSTALLATION (FOR 4-STROKE MODELS) F150 (L4 2.7L) ROUTING THE COOLANT TEMP. LEAD & COOLANT PRESS. TUE F150 (L4 2.7L) Secure with clamp Coolant temp. lead Coolant press. tube (1) (1) (2) Coolant temp. sensor (2) Coolant press. attachment F150C (VF150A), F165A, F175A, F200 (L4 2.8L) (2) Coolant temp. sensor Coolant press. tube Secure coolant temp. lead first with clamp (2) Coolant press. sensor 5-25

190 COOLANT TEMP. METER ROUTING THE COOLANT TEMP. LEAD & COOLANT PRESS. TUE F150C (VF150A), F165A, F175A, F200 (L4 2.8L) Coolant temp. lead Coolant temp. sensor SENSOR/ATTACHMENT INSTALLATION AND ROUTING F200, F225, F250 (V6) [Mechanical RC] w/ Variable Camshaft Timing Secure with clamp Coolant press. attachment Coolant temp. lead Coolant press. tube Coolant temp. lead Coolant press. tube Coolant temp. sensor 5-26

191 HOUR METER The hour meter provides the operator with useful at-a-glance information. It monitors the number of hours a motor has been used since original installation. * The transaction of time count when the engine is stopped differs on each hour meter and YDIS, therefore the elapsed time is not always equal on their equipment. 1 2 HOUR METER APPLICATIONS Ref. No. Description Part No. Applicable model 1 Mechanical 6Y Digital, lack panel 6Y All electrical start models Digital, White panel 6Y HOUR METER DIMENSIONS Mechanical Digital mm (in.) mm (in.) 60 (2.36) 52 (2.05) 62 (2.44) 52 (2.05) 11 (0.43) 71.5 (2.81) 33 (1.3) 7.5 (0.3) 34.5 (1.36) 31.5 (1.24) 5-27

192 HOUR METER WIRING THE MECHANICAL HOUR METER The hour meter counts while the ignition switch is ON. IG switch Y att.+12v Y L L GND Hour meter Lamp switch attery WIRING THE DIGITAL HOUR METER Two counting methods can be selected by connecting wires. COUNTING TIME WHILE ENGINE IS RUNNING IG switch COUNTING TIME WHILE IG SWITCH IS ON IG switch Y att.+12v Y att.+12v GND GND Y G Y Positive Negative Tach signal G Hour meter Lighting Coil (alternator) attery Positive Negative Power signal Hour meter G attery 5-28

193 VOLTAGE METER The voltage meter provides information about the charging condition of the battery. 1 2 VOLTAGE METER TYPES AND APPLICATIONS Ref. No. Description Part No. Applicable model DC 12 volt power supply 1 6Y lack panel All electrical start models DC 12 volt power supply 2 6Y White panel VOLTAGE METER DIMENSIONS mm (in.) 60 (2.36) 52 (2.05) 46.6 (1.83) 11 (0.43) 13.7 (0.54) WIRING THE VOLTAGE METER IG switch Y att.+12v Y L L Lamp switch Voltage meter attery 5-29

194 FUEL METER The fuel meter indicates the amount of fuel remaining in the fuel tank. However, a difference between the indication and actual remaining fuel may occur due to the fuel tank shape, design, etc. 1 2 FUEL METER TYPES AND APPLICATIONS Ref. No. Description Part No. Applicable model For Yamaha sensor (5 105 Ω) 6Y lack panel 1 For AYC sensor ( Ω) 6Y lack panel All electrical start models For Yamaha sensor (5 105 Ω) 6Y White panel 2 For AYC sensor ( Ω) 6Y White panel FUEL METER DIMENSIONS mm (in.) 60 (2.36) 52 (2.05) 46.6 (1.83) 11 (0.43) 13.7 (0.54) WIRING THE FUEL METER Lamp switch L L Fuel meter W Y Y W IG switch attery Fuel sensor (Yamaha, AYC, others) Fuel tank 5-30

195 CHARGE WARNING UNIT The lamp of the charge warning unit indicates the status of charging the battery. When the main switch is turned to ON position, the red lamp lights. After the engine starts, the lamp will go off. If the charging system has malfunctioned, the lamp will light. 7.7 (0.30) mm (in.) 84 (3.31) R G G Y 40 (1.57) 300 (11.81) CHARGE WARNING UNIT TYPES AND APPLICATIONS Description Part No. Remarks Relay All electrical start models with a rectifier/regulator ADDITIONAL PARTS REQUIREMENTS Description Part No. Remarks Red lamp V 10 (0.39) 20 (0.79) mm (in.) 42 (1.65) 500 (19.69) R G WIRING THE CHARGE WARNING UNIT Lamp R G Y IG switch Relay Charge warning unit G Lighting coil attery 5-31

196 WIRE HARNESSES An optional wire harness for the instruments is available. This harness will help set up any boats instruments. Choose a suitable wire-harness if necessary. For the wire color description, see the table on page REMOTE-OIL TANK HARNESS Part No. Length (L) Remarks 6R m (10 ft) For V4, V6 oil injection model. 6R m (16 ft) 6R m (26 ft) (LU) (LU) * Depending on the model, an 8 m (26 ft) wire harness is accompanied in the engine crate. ADDITIONAL ACCESSORY LEAD Part No. Length (L) Remarks 6Y cm (1 ft) lue 6Y cm (1 ft) lack 6Y cm (1 ft) Yellow L Y ( L ) Part No. Length (L) Remarks m (28 in) L/H model GND for gauges ( L ) 5-32

197 WIRE HARNESSES METER HARNESS For analog meter Part No. Length (L) Remarks 6Y m (8 ft) For all models except V4/V6 G Y Y (10A) Part No. Length (L) Remarks 6Y5-8350U mm (8 in) G Y Part No. Length (L) Remarks 6Y m (16 ft) For pre-mixed model G G Y ( L ) ( L ) Y L G Y L G Y G Y For digital meter Part No. Length (L) Remarks 6Y N0 2.5 m (8 ft) For twin engine application R G Y (10A) R R Y Y Y L (10A) R G Y L Part No. Length (L) Remarks 6Y M0 2.5 m (8 ft) For single engine application R G Y ( L ) Part No. Length (L) Remarks 6Y m (8 ft) L/H model G Y (10A) R R Y Y Y L (10A) Y ( L ) (10A) Y ( L ) Y L R G Y L G Y L G/R G/R Part No. Length (L) Remarks 6Y5-8356N m (5 ft) Extension harness ( L ) ( L ) 5-33

198 WIRE HARNESSES LAMP SWITCH Part No. Length (L) Remarks cm (4 in) t = Max.15 mm t L Y TRIM AND OIL LEAD Part No. Length (L) Remarks 6Y m (16 ft) 6Y m (19 ft) Above F30 (*1), Above 40 (3-cyl) w/ 6Y m (23 ft) oil injection 6Y m (26 ft) (Unified 4-pin coupler) 6Y m (29 ft) 6Y m (34 ft) (*1) Mechanical RC ( L ) P Gy Gy P Part No. Length (L) Remarks cm (4 in) t = Max.3 mm G/R G G G/R t L Y ( L ) TRIM METER LEAD Part No. Length (L) Remarks 6R m (10 ft) 6R R R R m (16 ft) 7 m (23 ft) 8 m (26 ft) 9 m (29 ft) ( L ) Premixed models w/ PTT (Flat type harness) COMINATION TRIM AND OIL LEAD Part No. Length (L) Remarks 68F m (16 ft) 68F m (23 ft) 68F m (26 ft) 250G, L250G 68F m (29 ft) 68F A m (34 ft) Or Gy P (TRIM) P Or Gy Or Or P Gy Gy P ( L ) ( L ) W/R L/W (TACH) L/W W/R G/R G G G/R 5-34

199 WIRE HARNESSES CONVERSION HARNESS 1 Part No. Length (L) Remarks 6Y5-8350U mm (6 in) To freeze trimgauge for hydrotilt model X (*1) For tachometer 6Y5-8350T-90 (L) X X RECTIFIER KIT Part No. Length (L) Remarks m (7 ft) M-start model with lighting coil R G 20A To GND R To Lighting coil R To irect current equipment G G/R To tachometer G/R G G/R G To EXT wire-harness 300 mm 11.8 in ( L ) FUEL MANAGEMENT GAUGE HARNESS Part No. Length (L) Remarks 6Y F1 8 m (26 ft) Pu/W Or/ Pu/W Or/ Pu Or W/R Or Pu Fuel sensor S P Gauge W/R Water detection SW (OP) ( L ) LIGHTING COIL EXTENSION HARNESS Part No. Length (L) Remarks m (19 ft) M-start model with lighting coil G G G G ( L ) 5-35

200 WIRING DIAGRAMS Some representative wiring diagram samples for Yamaha genuine remote controls and instruments are shown here. These diagrams will cover most common configurations. WIRE COLOR CODE The wiring color code and the main usage for the electric wires are shown below. The wire color and its main usage are different between Yamaha standard and AYC standard. * For the wires which use tracer stripes, the main color is followed by a slash then the tracer color. For example: R/G = Red wire with a green tracer stripe Pu/W = Purple wire with a white tracer stripe Color Main usage Wire color Color sample code Yamaha standard AYC standard lack Ground, attery ( ) Ground /R lack/red Remote-oil tank /W lack/white Ignition coil primary r rown Neutral switch Generator Ch Chocolate Dg Dark green G Green Lighting coil 1 (tach signal 1) G/R Green/Red Oil warning G/W Green/White Lighting coil 2 (tach signal 2) Gy Gray Warning signal Tacho signal L lue Instrument light, Remote choke Instrument light Lg Light green Trim down Or Orange Accessory feed Or/ Orange/lack P Pink Overheat warning, Trim signal Fuel sensor Pu Purple ECM Ignition Pu/W Purple/White R Red attery (+) attery (+) Sb Sky blue Trim up Oil pressure V Violet W White Engine stop switch W/R White/Red Pulser coil X Not used Y Yellow Accessory feed Y/R Yellow/Red Diagnosis Starting motor 5-36

201 WIRING DIAGRAMS DIGITAL METER (6Y5) SINGLE ENGINE APPLICATION 250G GPS NMEA 0183 FUEL (*1) 6Y F0 6Y S0 6Y5-8350T-03 (* 1) Select either speedometer or GPS (NMEA0183) If GPS is connected, speed hose is not required. (* 2) Water separator (Market obtainable) 6R : 3 m (10 ft) -50 : 5 m (16 ft) -80 : 8 m (26 ft) (*2) OUT IN Fuel tank 6Y F1 : 8 m (26 ft) 6Y Y M0 : 2.5 m (8 ft) Engine Oil Tank Speed hose (* 1) 68F : 5 m (16 ft) -60 : 6 m (19 ft) -70 : 7 m (23 ft) -80 : 8 m (26 ft) -90 : 9 m (29 ft) -A0 : 10.5 m (34 ft) (+) SPEED TACH Remote Oil Tank 5-37

202 WIRING DIAGRAMS DIGITAL METER (6Y5) SINGLE ENGINE w/ SIDE-MOUNT RC Above 115 w/ oil injection (except 250G), Above F115 (Mechanical RC) OUT 2-stroke oil injection (*1) IN 6R : 3 m (10 ft) -50 : 5 m (16 ft) -80 : 8 m (26 ft) (*2) Fuel tank 6Y F1 : 8 m (26 ft) Speed hose (* 1) FUEL SPEED TACH 6Y5-8350T-90 GPS 6Y F0 6Y S0 (* 1) Select either speedometer or GPS (NMEA0183) If GPS is connected, speed is not required. (* 2) Water separator (Market obtainable) SPEED/FUEL Speed hose (* 1) 6Y M0 : 2.5 m (8 ft) Y F0 (+) GPS NMEA 0183 (+) NMEA Y Remote Oil Tank Engine Oil Tank 6Y : 5 m (16 ft) -10 : 6 m (19 ft) -20 : 7 m (23 ft) -30 : 8 m (26 ft) -40 : 9 m (29 ft) -50 : 10.5 m (34 ft) 5-38

203 WIRING DIAGRAMS DIGITAL METER (6Y5) SINGLE ENGINE W/ INNACLE RC Above 115 w/ oil injection (except 250G), Above F115 (Mechanical RC) (* 1) Select either speedometer or GPS (NMEA0183) If GPS is connected, speed hose is not required. (* 2) Water separator (Market obtainable) Speed hose (* 1) 2-stroke oil injection 6R : 3 m (10 ft) -50 : 5 m (16 ft) -80 : 8 m (26 ft) 6Y OUT IN (*2) Fuel tank SPEED (*1) 6Y N0 : 2.5 m (8 ft) Y : 5 m (16 ft) -10 : 6 m (19 ft) -20 : 7 m (23 ft) -30 : 8 m (26 ft) -40 : 9 m (29 ft) -50 : 10.5 m (34 ft) Engine Oil Tank Remote Oil Tank 6Y F1 : 8 m (26 ft) A-50 (5 m) -60 (6 m) -70 (7 m) 6K1-8258A-40 (8 m) A-00 (9.5 m) SPEED/FUEL Speed hose (* 1) 6Y F0 (+) GPS NMEA Y F0 TACH 6Y5-8350T-90 FUEL NMEA 0183 GPS (+) 6Y S0 5-39

204 WIRING DIAGRAMS DIGITAL METER (6Y5) TWIN ENGINE W/ INNACLE RC 250G/L250G NMEA R : 3 m (10 ft) -50 : 5 m (16 ft) -80 : 8 m (26 ft) GPS (*1) TACH 6Y5-8350T-03 68F : 5 m (16 ft) -60 : 6 m (19 ft) -70 : 7 m (23 ft) 6Y : 8 m (26 ft) OUT IN -90 : 9 m (29 ft) -A0 : 10.5 m (34 ft) FUEL Y F1 : 8 m (26 ft) (*2) OUT Fuel tank IN 6Y M0 : 2.5 m (8 ft) 6Y : 2.5 m (8 ft) Engine Oil Tank A-50 : 5 m (16 ft) -60 : 6 m (19 ft) -70 : 7 m (23 ft) 6K1-8258A-40 : 8 m (26 ft) A-00 : 9.5 m (32 ft) Remote Oil Tank Speed hose (* 1) (* 1) Select either speedometer or GPS (NMEA0183) If GPS is connected, speed hose is not required. (* 2) Water separator (Market obtainable) TACH Remote Oil Tank Engine Oil Tank 6Y F0 6Y S0 (+) SPEED 5-40

205 WIRING DIAGRAMS DIGITAL METER (6Y5) TWIN ENGINE W/ INNACLE RC Above 115 w/ oil injection (except L/250G), Above F115 (Mechanical RC) Y N0 : 2.5 m (8 ft) Speed hose (* 1) (*2) OUT IN Fuel tank (*1) NMEA 0183 (* 1) Select either speedometer or GPS (NMEA0183) If GPS is connected, speed hose is not required. (* 2) Water separator (Market obtainable) SPEED/FUEL 6R : 3 m (10 ft) -50 : 5 m (16 ft) -80 : 8 m (26 ft) 6Y : 5 m (16 ft) -10 : 6 m (19 ft) -20 : 7 m (23 ft) 6Y : 8 m (26 ft) OUT IN -40 : 9 m (29 ft) -50 : 10.5 m (34 ft) 6Y F1 : 8 m (26 ft) Speed hose (* 1) A-50 : 5 m (16 ft) -60 : 6 m (19 ft) -70 : 7 m (23 ft) 6K1-8258A-40 : 8 m (26 ft) A-00 : 9.5 m (32 ft) 6Y F0 GPS 6Y : 2.5 m (8 ft) Engine Oil Tank Remote Oil Tank FUEL TACH 6Y S0 SPEED 2-stroke oil injection 2-stroke oil injection Engine Oil Tank Remote Oil Tank 6Y F0 (+) GPS NMEA 0183 TACH 6Y5-8350T-90 (+) 5-41

206 WIRING DIAGRAMS ANALOG METER (6Y7) 2-STROKE ENGINES 250G/L250G & Premixed engines For pre-mixed models Trim meter Tachometer without oil indicator Relay ASSY 6Y Y Lamp switch Fuse Tachometer with oil indicator Speedometer Charge warning unit Water pressure meter Voltage meter Charge lamp Water temperature meter Fuel meter Mechanical hour meter Digital hour meter Engine is running Main switch is ON Thermo sensor Fuel sensor 64D : 5 m (16 ft) -70 : 7 m (23 ft) -80 : 8 m (26 ft) -90 : 9 m (29 ft) 6Y : 2.5 m (8 ft) YAMAHA 6Y Y Y

207 WIRING DIAGRAMS ANALOG METER (6Y7) 2- AND 4-STROKE ENGINES Above 40 [3-cyl.] w/ oil injection (except L/250G), Above F30 (Mechanical RC) 6Y Y Y Y : 5 m (16 ft) -10 : 6 m (19 ft) -20 : 7 m (23 ft) -30 : 8 m (26 ft) -40 : 9 m (29 ft) -50 : 10.5 m (34 ft) Lamp switch Fuse 6Y : 2.5 m (8 ft) Water temperature meter Fuel meter Trim meter 6Y (LK) -50 (WHT) Speedometer Mechanical hour meter YAMAHA Thermo sensor Fuel sensor Engine is running Tachometer 6Y (LK) -90 (WHT) Digital hour meter Main switch is ON Voltage meter Water pressure meter Charge warning unit Charge lamp 5-43

208 WIRING DIAGRAMS INTERCHANGEAILITY ETWEEN TACHOMETER AND ENGINE (up to 2006 and after 2007) The wire-harness adapter is available for connection between 2006 and former engines and 2007 and later gauges or between 2006 and former gauges and 2007 and later engines. The water detection warning and check engine warning are no longer activated if either 2007 and later engines or 2007 and later gauges are installed. Wire-harness adapter 1 P/N: 6Y P Gy X X P P G/R G/W G/W G/R ENGINE O /W /W O GAUGE Gy P P Gy 30 cm (1 ft) Wire-harness adapter 2 P/N: 6Y X X Gy P Gy Gy G/R G/W G/W G/R ENGINE GAUGE X Gy P 30 cm (1 ft) For US and Canada The interchangeability between engine and gauge for model year is shown in the table below. Engine Gauge Interchangeability OK OK Requires 6Y Requires 6Y OK OK 5-44

209 WIRING DIAGRAMS ANALOG TACHOMETER 4-stroke engine (Fuel injected engines, F30A (F30), F40 (F40), FT50C, F50D, F95A and F100) Engine Conventional EXT wire harness Wire harness adapter Gauge 6Y / Wire harness adapter 2 6Y : 30 cm (1 ft) 1 (*1) 1 6Y / Y / Signal description (1) Trim GND (2) Overheat signal (3) Oil level signal (RED) (4) Oil level signal (GRN) (5) Trim signal (6) Oil press. signal (7) Water detection signal (8) Check engine signal ( ) Not used Combination trim and oil lead 68F : 5 m (16 ft) 68F : 6 m (19 ft) 68F : 7 m (23 ft) 68F : 8 m (26 ft) 68F : 9 m (29 ft) 68F A0 : 10.5 m (34 ft) 5 Wire harness adapter 1 6Y : 30 cm (1 ft) (*1) Connect to the ground wire. 5 6Y /20 2-stroke engine (HPDI engines: 2007-, carbureted engines w/ oil injection: 2008-) Engine 8 7 Conventional EXT wire harness Wire harness adapter 7 8 (*2) Gauge Y / Wire harness adapter 2 6Y : (30 cm, 1 ft) 1 1 6Y / Y / (*3) Relay Signal description (1) Trim GND (2) Overheat signal (3) Oil level signal (RED) (4) Oil level signal (GRN) (5) Trim signal (6) Oil press. signal (7) Water detection signal (8) Check engine signal ( ) Not used Combination trim and oil lead 68F : 5 m (16 ft) 68F : 6 m (19 ft) 68F : 7 m (23 ft) 68F : 8 m (26 ft) 68F : 9 m (29 ft) 68F A0 : 10.5 m (34 ft) 5 Wire harness adapter 1 6Y : 30 cm (1 ft) (*2) Disconnect the gray wire and insulate the terminals. 5 6Y /20 (*3) Oil level signal (YLW) 5-45

210 WIRING DIAGRAMS DIGITAL TACHOMETER 4-stroke engine (Fuel injected engines, F30A (F30), F40 (F40), FT50C, F50D, F95A and F100) Conventional EXT Engine Wire harness adapter wire harness Gauge (*1) 1 Wire harness adapter 2 6Y : 30 cm (1 ft) Y5-8350T TACH x100 r/min h set mode Signal description (1) Trim GND (2) Overheat signal (3) Oil level signal (RED) (4) Oil level signal (GRN) (5) Trim signal (6) Oil press. signal (7) Water detection signal (8) Check engine signal ( ) Not used Combination trim and oil lead 68F : 5 m (16 ft) 68F : 6 m (19 ft) 68F : 7 m (23 ft) 68F : 8 m (26 ft) 68F : 9 m (29 ft) 68F A0 : 10.5 m (34 ft) 5 Wire harness adapter 1 6Y : 30 cm (1 ft) (*1) Connect to the ground wire. 5 6Y5-8350T-03 2-stroke engine (HPDI engines: 2007-, carbureted engines w/ oil injection: 2008-) Engine Conventional EXT Wire harness adapter wire harness Gauge (*2) Wire harness adapter 2 6Y : 30 cm (1 ft) Y5-8350T TACH x100 r/min h set mode 5 2 Wire harness adapter 1 6Y : 30 cm (1 ft) 2 5 6Y5-8350T-03 Signal description (1) Trim GND (2) Overheat signal (3) Oil level signal (RED) (4) Oil level signal (GRN) (5) Trim signal (6) Oil press. signal (7) Water detection signal (8) Check engine signal ( ) Not used Combination trim and oil lead 68F : 5 m (16 ft) 68F : 6 m (19 ft) 68F : 7 m (23 ft) 68F : 8 m (26 ft) 68F : 9 m (29 ft) 68F A0 : 10.5 m (34 ft) (*2) Disconnect the gray wire and insulate the terminals. 5-46

211 RIGGING GROMMET DESCRIPTION * If the optional equipment will be installed, cut out the surface skin of rigging grommet on the prescribed position. 2-STROKE V4 OIL INJECTION Throttle cable Fuel hose Remote oil hose Coolant temp. lead (OP) Coolant press. tube (OP) Shift cable Speed hose 10-pin main harness Gauge harness & Remote oil tank lead attery cable 2-STROKE V6 (2.6L) OIL INJECTION 10-pin main harness Throttle cable Speed hose Fuel hose Gauge harness Coolant press. tube and/or Coolant temp. lead (OP) Remote oil tank lead Shift cable Remote oil hose attery cable Isolator cable (OP) 2-STROKE V6 (3.1L & 3.3L) 10-pin main harness Throttle cable Gauge harness Remote oil tank lead Shift cable Coolant press. tube and/or Coolant temp. lead (OP) Fuel hose Speed hose Remote oil hose Isolator cable (OP) attery cable 5-47

212 RIGGING GROMMET DESCRIPTION F75, F80, F90, F100, F115A Coolant press. tube or Coolant temp. lead (OP) Speed hose 10-pin main harness Throttle cable Gauge harness attery cable Shift cable Fuel hose F115 Throttle cable 6Y8 multifunction meter harness (pigtail bus wire) Speed hose Trolling switch harness Position the hose clip end as shown Gauge harness Fuel hose Shift cable attery cable 10-pin main harness F150 (L4 2.7L) 10-pin main harness Coolant temp. lead (OP) Throttle cable Coolant press. tube (OP) Flushing hose (Market OP) Isolator cable (OP) attery cable Shift cable Speed hose Gauge harness Fuel hose 5-48

213 RIGGING GROMMET DESCRIPTION F200, F225, F250 (V6-3.3L) w/ Variable Camshaft Timing [Mechanical RC] Coolant temp. lead and/or Coolant press. tube (OP) 10-pin main harness Throttle cable Isolator cable (OP) Flushing hose (Market OP) Shift cable Speed hose attery cable Gauge harness Fuel hose F200, F225, F250, F275 VMAX (SHO) and F150, F165, F175, F200(L4-2.8L) Coolant temp. wire/ pressure tube (OP) (for conventional gauge) 10-pin main wire-harness Throttle cable Fuel hose M6 bolt: 8 Nm, 0.8 kgf m, 13 ft lb Flushing hose (market OP) Speed hose Shift cable Gauge wire-harness or Pigtail bus wire attery cable Position the hose clip end as shown F200 (L4-2.8L), F225, F250, F300 (V6-4.2L) [DEC] 16-pin main wire-harness Isolator cable (OP) Fuel hose M6 bolt: 8 Nm, 0.8 kgf m, 13 ft lb Flushing hose (market OP) Speed hose attery cable Position the hose clip end as shown 5-49

214 RIGGING GROMMET DESCRIPTION F350 [DEC] 16-pin main harness attery cable olt: 10 Nm, 1.0 kgf m, 7.4 ft lb Flushing hose (Market OP) Speed hose (OP) Fuel hose Isolator cable (OP) Position the hose clip end as shown 5-50

215 DIGITAL NETWORK GAUGE (6Y8) DIGITAL NETWORK GAUGE COMPATILE MODELS DIGITAL NETWORK GAUGE APPLICATION SQUARE STYLE GAUGE APPLICATION ROUND STYLE GAUGE APPLICATION DIGITAL NETWORK GAUGE DIMENSIONS SQUARE STYLE GAUGE DIMENSIONS ROUND STYLE GAUGE DIMENSIONS OPTIONAL EQUIPMENT MULTI-SENSOR APPLICATION FITTING PLATE SPEED SENSOR KIT COOLANT PRESSURE SENSOR KIT SPEED/COOLANT PRESSURE SENSORS KIT WIRE HARNESS MAIN US WIRE PIGTAIL US WIRE SYSTEM POWER SUPPLY WIRE IMMOILIZER POWER DISTRIUTION WIRE FUEL TANK / GPS WIRE NETWORK HU OPTIONAL EQUIPMENT NMEA2000 GATEWAY ANALOG GAUGE INTERFACE (IF) IMMOILIZER UNIT NETWORK WIRING DIAGRAMS FUEL INJECTED F30-F250 [Mechanical RC] & HPDI ENGINES FUEL INJECTED F30-F250 [Mechanical RC] & HPDI ENGINES INITIAL GAUGE SETUP SETTING FOR GAUGE WHEN 6Y9 MULTI-SENSOR IS CONNECTED TROULESHOOTING ASIC REQUIREMENTS NMEA0183 COMPATILE EQUIPMENT CONNECTION DIGITAL NETWORK GAUGE (6Y8) FUNCTION TALE

216 DIGITAL NETWORK GAUGE COMPATILE MODELS The following models can accept the digital network gauges. Electronic fuel injected 4-stroke engines HPDI engines * US & Canada: 2006 and later models * Others: 2007 and later models Also, those engines can accept the conventional gauges 6Y5 and 6Y7 (square meters are not compatible with DEC engines). Therefore, you must select one of two gauge systems. If you select the digital network gauge system, see the information below. For further information, see the applicable service guide, installation manual, etc. DIGITAL NETWORK GAUGE APPLICATION SQUARE STYLE GAUGE APPLICATION Large digital display and dot matrix expression design Ref. No. Part name Part No. Remarks 1 Tachometer 6Y8-8350T-01 2 Speedometer 6Y8-8350S-01 Requires optional speed sensor, or NMEA compatible GPS 3 Fuel management gauge 6Y8-8350F-01 4 Speedometer and Fuel meter unit 6Y Requires optional speed sensor, or NMEA compatible GPS 6-2

217 DIGITAL NETWORK GAUGE APPLICATION ROUND STYLE GAUGE APPLICATION Similar shape design as conventional 6Y5 digital gauges. Compatible with both 6Y8 and 6Y9 networks. 1 2 Ref. No. Part name Part No. Remarks 1 Tachometer 6Y8-8350T-20 2 Speedometer and Fuel meter unit 6Y Requires optional speed sensor, or NMEA compatible GPS DIGITAL NETWORK GAUGE DIMENSIONS SQUARE STYLE GAUGE DIMENSIONS SURFACE MOUNT mm (in.) FLUSH MOUNT mm (in.) 6-3

218 DIGITAL NETWORK GAUGE DIMENSIONS ROUND STYLE GAUGE DIMENSIONS mm (in.) 0.5 (0.02) Template * Gasket thickness 6-4

219 OPTIONAL EQUIPMENT MULTI-SENSOR APPLICATION oat speed, water depth and water surface temperature can be obtained. For installation, see the instruction which is accompanied with the sensor. 1 mm (in.) 2 mm (in.) 52 (2.05) 96 (3.78) 4900 (16 ft) 3050 (10 ft) R 60 (2.36) R W L 130 (5.12) W L 125 (4.92) 50.8 (2) Ref. No. Part name Part No. Remarks 1 Transom multi-sensor 6Y Thru-hull multi-sensor 1 6Y Plastic body Thru-hull multi-sensor 2 6Y ronze body FITTING PLATE If the fitting surface is rough, insert the plate between a board and the ring nut of gauge (0.45) mm (in.) 95 (3.74) 85.5 (3.37) t = 1.5 (0.06) 6Y Part No. Remarks 6-5

220 OPTIONAL EQUIPMENT SPEED SENSOR KIT Used to pick up the pitot tube pressure for water speed. For installation and connection, see the instruction in the kit. The speed sensor kit may be included in the rigging kit. 1 2 Ref. No. Kit Part No. Remarks 1 60V-8A4L1-13 Fuel injected F30-F300 (V6), HPDI 2 6AW-8A4L1-01 F350, additional transom pitot tube ( ) and pressure tube ( ) required. COOLANT PRESSURE SENSOR KIT Used to pick up the coolant pressure of engine. For installation and connection, see the instruction in the kit Ref. No. Kit Part No. Remarks 1 60V-8A4L0-14 Fuel injected F30-F115, HPDI 2 69J-8A4L0-20 F200-F225 (3.3L) 3 63P-8A4L0-01 F150, F200 (2.8L), F200-F250 (3.3L-VCT), F225-F300 (4.2L) * For F350, factory-installed as standard. 6-6

221 OPTIONAL EQUIPMENT SPEED/COOLANT PRESSURE SENSORS KIT Ref. No. Kit Part No. Remarks 1 60V-8A4L2-02 F115A, F

222 WIRE HARNESS MAIN US WIRE Used to connect between the hub and hub. Part No. Length Remarks 6Y m (30 ft) 6Y m (25 ft) 6Y m (20 ft) 6Y m (15 ft) 6Y m (10 ft) 6Y m (1 ft) R W L (GRY) Length R W L (GRY) PIGTAIL US WIRE Used to connect between the hub and gauge and/or between the engine and the hub. Part No. Length Remarks 6Y m (12 ft) 6Y m (9 ft) 6Y m (6 ft) 6Y m (3 ft) 6Y m (2 ft) 6Y m (1 ft) L R W (WHT) Length R L W (WHT) SYSTEM POWER SUPPLY WIRE Used to connect between the switch panel and the hub, and supply the electric power to the system. Part No. 6Y Remarks With 10 amp fuse (RED) Y 2400 (94) Y mm (in.) Y (10A) 70 (2.75) 170 (6.63) IMMOILIZER POWER DISTRIUTION WIRE 1 This wire lead is used to supply permanent electric power to the immobilizer unit in case of multiapplication. Part No. 6H Remarks For fuel injection F30 F/FL200 multi-application w/ immobilizer R 90 (3.54) mm (in.) R 240 (9.45) 6-8

223 WIRE HARNESS FUEL TANK / GPS WIRE Used to connect between a fuel tank level sensor and/or an MNEA0183 compatible GPS and the speedometer (with fuel mgt gauge). Part No. 6Y8-8356N-01 Remarks Twin fuel tanks acceptable P/ mm (in.) P GPS W (+) L (GND) Fuel tank P/ P L W (LK) 220 (8.66) 300 (11.8) NETWORK HU Used to distribute the digital signal and electric power to the gauges and the other hubs. Ref. No. Part name Part No. Remarks 1 Multi-hub 6Y With ending resistor cap (P/N: 6Y ) 2 Single hub (Inline hub) 6Y Included ending resistor 3 2-pin sealing cap, RED 6Y pin sealing cap, WHT 6Y Same as bus wire cap of engine wire harness 1 mm (in.) 2 mm (in.) (0.88) (0.77) 42 (1.65) (7.67) 178 (7.01) Resistor cap (GRY) 10 (0.39) 41.4 (1.63) 21.4 (0.84) 7 (0.28) (1.02) (RED) 26 (1.02) (WHT) 19.3 (0.76) (0.73) (0.94) * Face the connectors downward for installation (0.79) (WHT) 6-9

224 OPTIONAL EQUIPMENT NMEA2000 GATEWAY Used to connect between NMEA2000 compatible equipment and network hub. Part No. 6Y9-8A2D0-20 Remarks Compatible with 6Y8 and 6Y9 protocols mm (in.) 130 (5.12) 116 (4.57) 20.5 (0.81) 5.5 (0.22) To NMEA2000 equipment To network hub via wire-lead 6Y YELLOW 4.8 (0.19) (0.47) 56 (2.20) 1.8 (0.07) 7.8 (0.31) 500 (19.7) ANALOG GAUGE INTERFACE (IF) Used to connect between analog gauge and network hub. Part No. 6Y9-8A2D0-30 Remarks Compatible with 6Y8 and 6Y9 protocols, Required for each engine. mm (in.) To wire-harness 6Y To analog tachometer via trim/oil lead 6Y *0 To hub via wire-lead 6Y (15.8) 1.8 (0.07) 7.8 (0.31) 4.6 (0.18) 12 (0.47) (4.57) 20.5 (0.81) 16 (0.63) 5.5 (0.22) 56 (2.20) Engine selection for analog tachometer: 130 (5.12) Single engine Twin engine Triple engine Quad engine PORT engine PORT engine PORT engine PORT engine STD engine CENTER engine STD engine CENTER PORT engine CENTER STD engine STD engine L Or L Or L Or L Or 6-10

225 IMMOILIZER UNIT Immobilizer acceptable model: Fuel injection F30 and F40 Fuel injection F40(4-cyl) up to F100 (2010 and later model) F/FL115 (2011 and later model) F/FL150 (manufactured after January 2012) F150C (VF150), F165A (L4-2.8L), F/FL225 (F/LF225CA), F/FL250 (F/LF250CA), F/FL300 (F/LF300CA) offshore (V6-4.2L), F200D (VF200), F225D (VF225), F250C (VF250), F225G, F250F, F275A (V6-4.2L), F175A, F/FL200F (F/LF200), F/FL200G (F/LF200CA) F/FL350 (2011 and later model) Yamaha Security System limits the engine speed to the specified level. Part No. 6Y Y Y Y Remarks For EU, RC For EU, F30/F40 tiller handle For US/ANZ, RC For JPN, RC 36 (1.42) 8.5 (0.33) 112 (4.41) 104 (4.09) 9 (0.35) 6.9 (0.27) 200 (7.87) 2400 (94.5) (*1) (WHT) R 9 (0.35) 128 (5.04) 146 (5.75) (*1) 3700 mm (146 in) for F30/F40 tiller handle 6-11

226 NETWORK WIRING DIAGRAMS FUEL INJECTED F30-F250 [Mechanical RC] & HPDI ENGINES SINGLE ENGINE APPLICATION Coolant press. sensor (OP) Trim sensor FUEL TANK Single-hub with resistor SPEED/FUEL Fuel injected F30 F/FL200 NMEA 0183 (GND) (+) GPS Fuse (10A) Speed sensor TACH ECM Multi-hub Resistor 6-12

227 NETWORK WIRING DIAGRAMS FUEL INJECTED F30-F250 [Mechanical RC] & HPDI ENGINES TWIN ENGINE APPLICATION (Simple) Coolant press. sensor (OP) Speed sensor Coolant press. sensor (OP) ECM ECM Trim sensor Trim sensor FUEL TANK 1 Single-hub with resistor Single-hub with resistor FUEL TANK 2 Fuse (10A) Multi-hub TACH(S) TACH(P) FUEL/SPEED (GND) (+) GPS NMEA 0183 P S 6-13

228 NETWORK WIRING DIAGRAMS FUEL INJECTED F30-F250 [Mechanical RC] & HPDI ENGINES TWIN ENGINE APPLICATION (Deluxe) Coolant press. sensor (OP) Speed sensor ECM Trim sensor Coolant press. sensor (OP) ECM Trim sensor Multi-sensor (OP) FUEL TANK 1 Multi-hub Cap Resistor FUEL TANK 2 TACH(S) TACH(P) Permanent power relay wire Fuse (10A) Multi-hub Immobilizer PWR distribution wire 1 Multi-hub Cap Cap Resistor (*1) Fuel injected F30 F/FL200 FUEL SPEED (GND) (+) GPS NMEA 0183 (* 1) Only one immobilizer is required. P S 6-14

229 NETWORK WIRING DIAGRAMS FUEL INJECTED F30-F250 [Mechanical RC] & HPDI ENGINES TRIPLE ENGINE APPLICATION Coolant press. sensor (OP) ECM Trim sensor Coolant press. sensor (OP) Speed sensor ECM Trim sensor Coolant press. sensor (OP) ECM Trim sensor Multi-sensor (OP) FUEL TANK 1 Multi-hub Cap Cap Cap Resistor Multi-hub FUEL TANK 2 Cap Multi-hub Cap Cap FUEL TACH(S) TACH(C) TACH(P) SPEED Fuse (10A) Multi-hub Resistor (GND) (+) GPS NMEA 0183 P C S 6-15

230 INITIAL GAUGE SETUP If two or more engines with digital network gauges are installed, the initial setup is required for proper gauge operation. The ignition switches have to be turned to ON in order from Port to Starboard in 2 seconds or more interval, which can memorize the engine number into each ECM by a rule. The 1st turned on ignition switch is memorized as No.1 engine. The 2nd turned on is memorized as No.2 engine. This can obtain easier engine number recognition for gauge setup. When the initial recognition setup has been stumbled, reset the engine number and perform it again with the tachometer. For further information, see the installation manual in the rigging kit. For DEC engines, the Digital Electronic Control system recognizes the engine number automatically, therefore the key switch ON in number order is not required. SETTING FOR GAUGE WHEN 6Y9 MULTI-SENSOR IS CONNECTED If the 6Y9 multi-sensor (6Y ) is connected to the conventional 6Y8 multifunction speed (speed/fuel) meters (6Y8-8350*-01 or 11), set the gauge as shown below to enable the sensor. 1. Press and hold the [SET] button for 10 seconds on the normal display. The mode "01" screen will appear. 2. Press the [MODE] button to select the mode "02". 3. Press the [SET] button for 1 second to finalize the setting and return to the normal display. TIP: If no button operation is made for 30 seconds while setting, the setting will be automatically cancelled and return to the normal display. 6-16

231 TROULESHOOTING The following table shows the main presumed troubles if the system or gauge is incorrectly set up, incorrectly operated, or malfunctioned. For detailed information, see the applicable installation manual and/or the troubleshooting guide. Symptom Cause Measure Note Tachometer shows incorrect engine RPM. Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level. Fuel mgt gauge shows incorrect remaining fuel Fuel mgt gauge shows incorrect fuel consumption Gauge display does not wakeup. Illumination does not light. Gauge shows Gauge unstably operates. Gauge response is poor or down. Trim gauge always shows fully tilted up position. Trim gauge shows incorrect position. oat speed and/or Coolant pressure gauge does not show. Oil pressure is not shown. Engine recognition is wrong. (for multi-applications) Fuel sensor selection is wrong. Fuel capacity setting is wrong. (for SQR Fuel mgt Gauge) Engine recognition is wrong. (for multi-applications) Electric power is not supplied. Gauge is damaged. Electric power is not supplied. Gauge is damaged. Digital signal is not received. Resistor is not connected to the ending hubs. Market obtainable unit connected to the system is failed. Signal volume has exceeded 50% of the capacity. Trim sensor signal is not received. Initial position setting is wrong. Trim sensor is damaged. Optional sensor is not installed. Monitor display of tachometer remains in the default setting. Engine does not have the oil pressure sensor. Tachometer is not setup to show the oil pressure. Push SET for 10 seconds to default the engine number. Memorize each engine number again. Setup the fuel sensor to correct resistance. Fill the tank with fuel, and set fuel tank capacity. Default the engine number, and turn the key switch on in order from portside engine to rememorize each engine number. Replace fuse. Connect the couplers securely. Replace the damaged wire or hub. Replace the gauge. Replace fuse. Connect the couplers securely. Replace the damaged wire or hub. Replace the gauge. Connect the couplers securely. Replace the damaged bus wire or hub. Connect the gray 6-pin cap to the ending multi-hubs. Replace the unit. Remove the heavy signal output unit. Connect pink lead connectors with each other. Put the motor in the fully trimmed-in position, and reset the initial (zero) trim angle. Replace the trim sensor. Install the optional sensor. Select the coolant pressure display. See Custom Mode for procedure to set the engine number. AYC sensor: Ω (Default) Europe sensor: Ω YAMAHA sensor: Ω Default setting is 50 gallons. See Custom Mode of Tachometer for procedure to setup the engine number. e sure to use 10 amp fuse. e sure to use 10 amp fuse. Verify the system with the checker. Single hub has a built-in resistor. Verify the system with the checker. See the installation manual. See Custom Mode for procedure to set the fully trimmed-in angle. See the instruction supplied with the sensor kit. See Custom Mode for procedure to select the display. NA Select the oil press. display. See Custom Mode to setup display. 6-17

232 ASIC REQUIREMENTS The following basic conditions are required to install the digital network gauge system onto a boat. Item Conditions Symptom Note Total amount quantity of unit for connecting to the system Total amount length of the main bus wires. Acceptable volume of digital communication signals us wires distance from electrical noise equipments (Antenna cable, Generator, Radio, etc.) Temperature for performing bus wires and hubs 50 units or less (Including market obtainable units, exclusive gauges and engine ECMs). 50 meter (164 feet) or less 50% or less of overall signal capacity 30 cm (1 ft) and more 80 C (176 F) or less Gauge display is unstable. Gauge response is poor. Check the system with the optional checker. Verify the conditions of system. NMEA0183 COMPATILE EQUIPMENT CONNECTION The digital network gauge system accepts the signal of NMEA0183 version 2.0, 2.1, or 3.01 with following sentences. Data Speed and Time Water depth Water surface temp. Sentence RMC DT MTW * If the signal sentence is not shown on an electric unit or its instruction, contact the manufacturer. 6-18

233 DIGITAL NETWORK GAUGE (6Y8) FUNCTION TALE 6-19 Global model US/CA model Engine trouble indicator Water detection indicator Cooling-water pressure sensor (OP) Speed sensor (OP) *For R/H model Low oil pressure indicator *For 4-stroke Low oil level indicator *For 2-stroke Variable trolling RPM (r/min) F30 F30A YES YES YES YES YES (switch) NA F40D, F40H YES YES YES YES YES (switch) NA F40F F40A YES YES YES YES YES (switch) NA F40G YES YES YES YES YES (switch) NA F50F, F50H F50A, F50 YES YES YES YES YES (switch) NA FT50G, FT50J T50A, T50 YES YES YES YES YES (switch) NA F60C, F60F F60A, F60 YES YES YES YES YES (switch) NA FT60D, FT60G T60A, T60 YES YES YES YES YES (switch) NA F70A F70A YES YES YES YES YES (switch) NA F75 F75A YES YES YES YES YES (switch) NA F80 YES YES YES YES YES (switch) NA F90 F90A YES YES YES YES YES (switch) NA F100D YES YES YES YES YES (switch) NA F/FL115A F/LF115A YES YES YES YES YES (switch) NA NA F/FL115 F/LF115 YES YES YES YES YES (switch) NA F/FL150A F/LF150A YES YES YES YES YES (sensor) NA NA F/FL150 YES YES YES YES YES (sensor) NA NA F150C VF150A YES YES YES YES YES (sensor) NA F165A YES YES YES YES YES (sensor) NA F/FL200 YES YES YES YES YES (sensor) NA NA F/FL200C F/LF200A YES YES YES YES YES (sensor) NA NA F/FL200F F/LF200 YES YES YES YES YES (sensor) NA F/FL200G F/LF200CA YES YES YES YES YES (sensor) NA F200D VF200A YES YES YES YES YES (sensor) NA NA F/FL225 F/LF225A YES YES YES YES YES (sensor) NA NA F/FL225F F/LF225CA YES YES YES YES YES (sensor) NA F225C YES YES YES YES YES (sensor) NA NA F225D VF225A YES YES YES YES YES (sensor) NA NA F/FL250A F/LF250A YES YES YES YES YES (sensor) NA NA F/FL250D F/LF250CA YES YES YES YES YES (sensor) NA F/FL250G YES YES YES YES YES (sensor) NA NA F250C VF250A YES YES YES YES YES (sensor) NA NA F/FL300A YES YES YES YES (transom pitot tube) YES (sensor) NA F/FL300 F/LF300CA YES YES YES YES YES (sensor) NA F/FL350A F/LF350C YES YES YES (STD) YES (transom pitot tube) YES (sensor) NA Z150Q VZ150TR YES YES YES YES NA YES NA

234 DIGITAL NETWORK PREMIUM GAUGE (6Y9) DIGITAL NETWORK PREMIUM GAUGE COMPATILE MODELS DIGITAL NETWORK PREMIUM GAUGE APPLICATION DIGITAL NETWORK PREMIUM GAUGE DIMENSIONS PREMIUM COLOR GAUGE DIMENSIONS OPTIONAL EQUIPMENT TRANSOM MULTI-SENSOR (6Y9) IMMOILIZER UNIT NMEA2000 GATEWAY ANALOG GAUGE INTERFACE (IF) SPEED SENSOR KIT COOLANT PRESSURE SENSOR KIT NETWORK HU WIRE HARNESS MAIN US WIRE PIGTAIL US WIRE GPS WIRE TANK WIRE SYSTEM POWER SUPPLY WIRE SYSTEM POWER DISTRIUTION WIRE IMMOILIZER POWER DISTRIUTION WIRE CONVERSION HARNESS CONVERSION HARNESS CONVERSION HARNESS CONVERSION HARNESS CONVERSION HARNESS CONVERSION HARNESS L TWINNING HARNESS CONVERSION HARNESS M (FOR 2ND HELM) CONVERSION HARNESS N (FOR 2ND HELM) CONVERSION HARNESS P (FOR 2ND HELM) CONVERSION HARNESS K (FOR DUAL STATION) To be continued. 7-1

235 DIGITAL NETWORK PREMIUM GAUGE (6Y9) NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION (6X6 binnacle mount Digital Electronic Control) SINGLE STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION (6X6 binnacle mount Digital Electronic Control) SINGLE STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION (6X7 concealed Digital Electronic Control) SINGLE STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION (6X7 concealed Digital Electronic Control) SINGLE STATION W/ 6Y9 GAUGE TWIN ENGINE APPLICATION SINGLE STATION W/ 6Y8 GAUGE TWIN ENGINE APPLICATION SINGLE STATION W/ 6Y9 GAUGE TRIPLE ENGINE APPLICATION SINGLE STATION W/ 6Y8 GAUGE TRIPLE ENGINE APPLICATION SINGLE STATION W/ 6Y9 GAUGE QUAD ENGINE APPLICATION (FOR F/LF225CA, F/LF250CA, F/LF300CA, F/LF350CA/) DUAL STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION DUAL STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION DUAL STATION W/ 6Y9 GAUGE TWIN ENGINE APPLICATION DUAL STATION W/ 6Y8 GAUGE TWIN ENGINE APPLICATION DUAL STATION W/ 6Y9 GAUGE TRIPLE ENGINE APPLICATION DUAL STATION W/ 6Y9 GAUGE QUAD ENGINE APPLICATION (FOR F/LF225CA, F/LF250CA, F/LF300CA, F/LF350CA/)

236 DIGITAL NETWORK PREMIUM GAUGE COMPATILE MODELS The following models can accept Digital Network Premium Gauge (6Y9 new network system). Global model US/CA/ANZ model Remarks F/FL200G F/LF200CA F/FL225F F/LF225CA F/FL250D F/LF250CA F/FL300 F/LF300CA F/FL350A F/LF350CA/ For 2011 and later models These engines can accept the conventional Digital Network Gauges (6Y8) as well. For further information, see the applicable models service guide, installation manual, etc. DIGITAL NETWORK PREMIUM GAUGE APPLICATION With TFT-LCD color screen, arrow key, and US port for triple engine application. Ref. No. Part name Part No. Remarks 1 Premium color gauge ASSY 6Y w/ screen cover (6Y ) 1 SET CANCEL MENU 7-3

237 DIGITAL NETWORK PREMIUM GAUGE DIMENSIONS PREMIUM COLOR GAUGE DIMENSIONS mm (in.) 11.9 (0.47) Reference: previous gauge (6.99) 98 (3.86) 45.0 (1.77) 85.0 (3.35) 98 (3.86) 98 (3.86) 4.2 (0.17) 38.0 (1.50) (5.00) (6.48) Template (0.74) (0.74) 7-4

238 OPTIONAL EQUIPMENT TRANSOM MULTI-SENSOR (6Y9) Part No. 6Y Remarks Depth, speed, water surface temp mm (in.) 4900 (193) 227 (8.95) 70 (2.77) To network hub via wire-lead 6Y (6.20) 99 (3.90) IMMOILIZER UNIT Yamaha Security System limits the engine speed to the specified level. Part No. 6Y Y Y For EU (STD) For US, ANZ For JPN Remarks mm (in.) 36 (1.42) 8.5 (0.33) 112 (4.41) 104 (4.09) 9 (0.35) 6.9 (0.27) 200 (7.87) 2400 (94.5) (WHT) R 9 (0.35) 128 (5.04) 146 (5.75) 7-5

239 OPTIONAL EQUIPMENT NMEA2000 GATEWAY Used to connect between NMEA2000 compatible equipment and network hub. Part No. 6Y9-8A2D0-20 Remarks Compatible with 6Y8 and 6Y9 protocols mm (in.) 130 (5.12) 116 (4.57) 20.5 (0.81) 5.5 (0.22) To NMEA2000 equipment To network hub via wire-lead 6Y YELLOW 4.8 (0.19) (0.47) 56 (2.20) 1.8 (0.07) 7.8 (0.31) 500 (19.7) ANALOG GAUGE INTERFACE (IF) Used to connect between analog gauge and network hub. Part No. 6Y9-8A2D0-30 Remarks Compatible with 6Y8 and 6Y9 protocols, Required for each engine. mm (in.) To wire-harness 6Y To analog tachometer via trim/oil lead 6Y *0 To hub via wire-lead 6Y (15.8) 1.8 (0.07) 7.8 (0.31) 4.6 (0.18) 12 (0.47) (4.57) 20.5 (0.81) 16 (0.63) 5.5 (0.22) 56 (2.20) Engine selection for analog tachometer: 130 (5.12) Single engine Twin engine Triple engine Quad engine PORT engine PORT engine PORT engine PORT engine STD engine CENTER engine STD engine CENTER PORT engine CENTER STD engine STD engine L Or L Or L Or L Or 7-6

240 OPTIONAL EQUIPMENT SPEED SENSOR KIT Used to pick up the pitot tube pressure for water speed. Kit Part No. 60V-8A4L1-13 Remarks Shared with 6Y8 network system COOLANT PRESSURE SENSOR KIT Used to pick up the coolant pressure of engine. Kit Part No. 63P-8A4L0-01 Remarks Shared with 6Y8 network system 7-7

241 NETWORK HU Shared between 6Y8 and 6Y9 network systems. Ref. No. Part name Part No. Remarks 1 Multi-hub 6Y w/ ending resistor cap (P/N: 6Y ) 2 Single hub (Inline hub) 6Y Included ending resistor 3 2P sealing cap, RED 6Y P sealing cap, WHT 6Y mm (in.) 2 mm (in.) (0.88) (0.77) 42 (1.65) (7.67) 178 (7.01) Resistor cap (GRY) 10 (0.39) 41.4 (1.63) 21.4 (0.84) 7 (0.28) (1.02) (RED) 26 (1.02) (WHT) 19.3 (0.76) (0.73) (0.94) * Face the connectors downward for installation (0.79) (WHT) 7-8

242 WIRE HARNESS MAIN US WIRE Used to connect between the hub and hub, between the RC and hub, etc. (shared with 6Y8 network system) Part No. Length Remarks 6Y m (30 ft) 6Y m (25 ft) 6Y m (20 ft) 6Y m (15 ft) 6Y m (10 ft) 6Y m (1 ft) R W L (GRY) Length R W L (GRY) PIGTAIL US WIRE Used to connect between the hub and gauge, between the hub and equipment (IF, gateway), etc. (shared with 6Y8 network system) Part No. Length Remarks 6Y m (12 ft) 6Y m (9 ft) 6Y m (6 ft) 6Y m (3 ft) 6Y m (2 ft) 6Y m (1 ft) L R W (WHT) Length L R W (WHT) GPS WIRE Used to connect between premium gauge and NMEA0183 compatible GPS unit. Part No. 6Y9-8356N-01 Remarks NMEA 0183 compatible GPS To GPS W (+) 350 (14) Green tube mm (in.) L (GND) L (GND) (LK) W (+) TANK WIRE Used to connect between the premium gauge and a fuel tank, fresh water tank, sewage tank, etc. Part No. Remarks 6Y9-8356N-10 4-tank acceptable mm (in.) P /P G /G P /P G /G r /r Or /Or Fuel tank #1 Fuel tank #2 Fuel tank #3 Fuel tank #4 270 (10.63) (LK) Or /Or r /r 7-9

243 WIRE HARNESS SYSTEM POWER SUPPLY WIRE Used to connect between the SW panel and the hub, and supply electric power to the system. Part No. 6Y Remarks Shared with 6Y8 network system (RED) Y 2400 (94) Y mm (in.) Y (10A) 70 (2.75) 170 (6.63) SYSTEM POWER DISTRIUTION WIRE Used to supply electric power to each network hub, if 6Y9 and 6Y8 network systems are simultaneously used. NOTICE Do not connect with the main bus wire between 6Y9 network and 6Y8 network. Part No. 6Y Remarks To SW panel To 6Y9 network hub (RED) Y Y (RED) 600 (23.6) Y (RED) mm (in.) To 6Y8 network hub IMMOILIZER POWER DISTRIUTION WIRE 2 Supplies electric power to activate the immobilizer system in case of multi-engine application. Part No. 6Y Remarks For start/stop button SW panel 2400 (94.5) mm (in.) To PWR supply wire (for network system) To SW panel (Twin, Triple) Y Y Y R To immobilizer unit L (WHT) Y W X R Fuse 5A To network hub R Y Fuse 5A Y To SW panel (Twin, Triple) R Y (LU) W (WHT) L R To immobilizer unit 7-10

244 WIRE HARNESS CONVERSION HARNESS Used to connect between DEC and network hub. Part No. 6Y Remarks For 6Y9 network system 310 (12.2) mm (in.) To RC W X W X L W (WHT) X X X X L W (GRY) To hub CONVERSION HARNESS 1 Used to connect between DEC and network hub if dual station system is used and multi-sensor is connected. Part No. 6Y Remarks For 6Y9 network system 310 (12.2) (GRY) mm (in.) To RC W L X X L W (WHT) X R X L W X R X L W (GRY) To hub #1 To hub #2 CONVERSION HARNESS 4 Used to connect between premium gauge and network hub. Part No. 6Y Remarks For 6Y9 network system To R hub W L (WHT) 150 (5.91) lack taping mm (in.) X R To L W premium X gauge (GRN) CONVERSION HARNESS 5 Used to connect between analog gauge IF/ Gateway and network hub. Part No. 6Y Remarks For 6Y9 network system 160 (6.3) mm (in.) To hub R W L (WHT) Green taping R X To W L gateway/ IF X (GRN) CONVERSION HARNESS 6 Used to connect between multi-sensor and network hub. Part No. 6Y Remarks For 6Y9 network system To hub R W L (WHT) 240 (9.45) Orange taping mm (in.) R L W L To multisensor W (GRN) 7-11

245 WIRE HARNESS CONVERSION HARNESS L Used to connect between new DEC unit and previous main switch. Part No. 6X6-8258A-L0 Remarks To DEC Y X W Pr X X R X X X 150 (6) Y r P W X R X mm (in.) To SW panel TWINNING HARNESS Used to connect between two engine group IG switches and emergency stop SW. (For quad engine DEC special) Part No. 6X6-8258A-U0 Remarks 100 (4) mm (in.) W X W X To emergency stop SW PORT engine group (P/CP) STD engine group (CS/S) W W To main helm SW panel PORT engine group (P/CP) STD engine group (CS/S) CONVERSION HARNESS M (FOR 2ND HELM) Used to connect between 2nd helm new DEC and 2nd helm previous start/stop SW. (Single engine application) Part No. 6X6-8258A-M0 Remarks 200 (7.87) mm (in.) To DEC YP r W X X X X Y X W r P To start/ stop SW CONVERSION HARNESS N (FOR 2ND HELM) Used to connect between 2nd station helm new DEC and 2nd helm previous start/stop SW. (Twin engine application) Part No. 6X6-8258A-N0 Remarks 240 (9.45) mm (in.) To DEC X X P r Y P r Y W X X W S P Y W r X P Y X W r P To start/ stop SW 7-12

246 WIRE HARNESS CONVERSION HARNESS P (FOR 2ND HELM) Used to connect between 2nd helm new DEC and 2nd helm previous start/stop SW. (Triple engine application) Part No. 6X6-8258A-P0 Remarks 240 (9.45) mm (in.) X P r Y X P r Y XPr Y P Y Wr X P To DEC W WW S Y X W r P To start/ stop SW C Y X W r P CONVERSION HARNESS K (FOR DUAL STATION) Used to connect between main helm new DEC and 2nd helm previous DEC. Part No. 6X6-8258A-K0 Remarks 230 (9.06) X r mm (in.) To previous DEC r Y X Y r r To new DEC r r 7-13

247 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION (6X6 binnacle mount Digital Electronic Control) (*1) For previous network system (6Y8) (*2) Engine selection for tachometer (*3) Connect the sensor ground leads to the ground (negative circuit on the battery) ECM Sewage tank Freshwater tank Fuel tank 2 Fuel tank 1 (*1) (*3) To NMEA2000 Network (*2) US 23 (+) (GND) GPS

248 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION (6X6 binnacle mount Digital Electronic Control) Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 2 Conversion harness 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 14 System power supply wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 10-amp fuse, 2.4 m (8 ft) Ref. No. 16 Multi-hub 6Y w/ resistor cap, lack 17 Single (inline) hub 6Y w/ resistor, 4-6P, White 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 6X6 binnacle mount Digital Electronic Control 40 Main switch 6X Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) Depth, speed, water temp, w/ 4.9 m (16 ft) wire 6X Single station For 6X6 binnacle mount Digital Electronic Control, Main station helm 7-15

249 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION (6X6 binnacle mount Digital Electronic Control) (*1) For 6Y9 network system ECM 19 1 Fuel tank (*1) TACH 12 9 SPEED/FUEL (GND) (+) Not used GPS 7-16

250 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION (6X6 binnacle mount Digital Electronic Control) Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 9 Fuel tank/ GPS wire 6Y8-8356N m (1 ft) 12 Main bus wire 13 Pigtail bus wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) Ref. No. 14 System power supply wire 6Y w/ 10-amp fuse, 2.4 m, 8 ft 16 Multi-hub 6Y w/ resistor cap, lack 17 Single (inline) hub 6Y w/ resistor, 4-6P, White 19 Transom multi-sensor 6Y Immobilizer unit 29 Part name Part No. Remarks 6X6 binnacle mount Digital Electronic Control 6Y EU 6Y US, ANZ 6Y JP 40 Main switch 6X Depth, speed, water temp, w/ 4.9 m (15 ft) wire 6X Single station For 6X6 binnacle mount Digital Electronic Control, Main station helm 7-17

251 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION (6X7 concealed Digital Electronic Control) (*1) For previous network system (6Y8) (*2) Engine selection for tachometer (*3) Connect the sensor ground leads to the ground (negative circuit on the battery) ECM Sewage tank Freshwater tank Fuel tank 2 Fuel tank 1 (*3) (*1) To NMEA2000 Network (*2) 25 US 23 (+) (GND) GPS

252 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION (6X7 concealed Digital Electronic Control) Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 2 Conversion harness 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 14 System power supply wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 10-amp fuse, 2.4 m (8 ft) Ref. No. 16 Multi-hub 6Y w/ resistor cap, lack 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 6Y EU 22 Immobilizer unit 6Y US, OCE 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 6X7 concealed Digital Electronic Control 43 Main switch 64D Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) Depth, speed, water temp, w/ 4.9 m (15 ft) wire 6X Single station For 6X7 concealed Digital Electronic Control 7-19

253 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION (6X7 concealed Digital Electronic Control) (*1) For 6Y9 network system ECM 19 1 Fuel tank (*1) TACH 12 9 SPEED/FUEL (GND) (+) Not used GPS 7-20

254 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION (6X7 concealed Digital Electronic Control) Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 9 Fuel tank/ GPS wire 6Y8-8356N m (1 ft) 12 Main bus wire 13 Pigtail bus wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) Ref. No. 14 System power supply wire 6Y w/ 10-amp fuse, 2.4 m (8 ft) 16 Multi-hub 6Y w/ resistor cap, lack 19 Transom multi-sensor 6Y Immobilizer unit 39 Part name Part No. Remarks 6X7 concealed Digital Electronic Control 6Y EU 6Y US, ANZ 6Y JP 43 Main switch 64D Depth, speed, water temp, w/ 4.9 m (15 ft) wire 6X Single station For 6X7 concealed Digital Electronic Control 7-21

255 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE TWIN ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For previous network system (6Y8) (*3) Engine selection for tachometer PORT engine STD engine (*4) Requires 2 pcs including its related parts (*5) Connect the sensor ground leads to the ground (negative circuit on the battery) P ECM 1 S ECM 19 6 Sewage tank Freshwater tank Fuel tank 2 Fuel tank 1 (*2) (*5) (*1) US 2 (+) (GND) GPS (*4) To NMEA2000 Network (*3)

256 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE TWIN ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 2 Conversion harness 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 15 Immobilizer PWR distribution wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 5-amp fuses, 2.4 m (8 ft) Ref. No. 16 Multi-hub 6Y w/ resistor cap, lack 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 6X6 binnacle mount Digital Electronic Control 6Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) Depth, speed, water temp, w/ 4.9 m (15 ft) wire 6X Single station 44 Main switch 6X Main station helm 45 Start/stop button 6X Main station helm 53 All start/stop button 6X C0 For single/twin/triple engine application 7-23

257 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE TWIN ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For 6Y9 network system (*1) P ECM 1 S ECM Fuel tank 2 19 Fuel tank (*2) TACH SPEED/FUEL TACH (GND) (+) GPS 7-24

258 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE TWIN ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 9 Fuel tank/gps wire 6Y8-8356N m (1 ft) 12 Main bus wire 13 Pigtail bus wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) Ref. No. 15 Immobilizer PWR distribution wire 6Y w/ 5-amp fuses, 2.4 m (8 ft) 16 Multi-hub 6Y w/ resistor cap, lack 19 Transom multi-sensor 6Y Immobilizer unit 32 Part name Part No. Remarks 6X6 binnacle mount Digital Electronic Control 6Y EU 6Y US, ANZ 6Y JP Depth, speed, water temp, w/ 4.9 m (15 ft) wire 6X Single station 44 Main switch 6X Main station helm 45 Start/stop button 6X Main station helm 53 All start/stop button 6X C0 For single/twin/triple engine application 7-25

259 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE TRIPLE ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For previous network system (6Y8) (*3) Engine selection for tachometer PORT engine CENTER engine STD engine (*4) Requires 3 pcs includig its related parts (*5) Connect the sensor ground leads to the ground (negative circuit on the battery) P ECM 1 C ECM S ECM 19 6 Sewage tank Freshwater tank Fuel tank 2 Fuel tank 1 (*2) (*5) (*1) To NMEA2000 Network (*4) (*3) US 23 (+) (GND) GPS

260 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE TRIPLE ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 2 Conversion harness 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 15 Immobilizer PWR distribution wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 5-amp fuses, 2.4 m (8 ft) Ref. No. 16 Multi-hub 6Y w/ resistor cap, lack 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 6X6 binnacle mount Digital Electronic Control 6Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) 6X Depth, speed, water temp, w/ 4.9 m (15 ft) wire Single & dual station/ Main station helm 47 Main switch 6X Main station helm 48 Start/stop button 6X Main station helm 53 All start/stop button 6X C0 For single/twin/triple engine application 7-27

261 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE TRIPLE ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For 6Y9 network system (*1) 13 P ECM C ECM 1 S ECM Fuel tank 2 19 Fuel tank (*2) TACH TACH FUEL MGT TACH 9 SPEED (GND) (+) GPS 7-28

262 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y8 GAUGE TRIPLE ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 9 Fuel tank/gps wire 6Y8-8356N m (1 ft) 12 Main bus wire 13 Pigtail bus wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) Ref. No. 15 Immobilizer PWR distribution wire 6Y w/ 5-amp fuses, 2.4 m (8 ft) 16 Multi-hub 6Y w/ resistor cap, lack 19 Transom multi-sensor 6Y Immobilizer unit 35 Part name Part No. Remarks 6X6 binnacle mount Digital Electronic Control 6Y EU 6Y US, ANZ 6Y JP 6X Depth, speed, water temp, w/ 4.9 m (15 ft) wire Single & dual station/ Main station helm 47 Main switch 6X Main station helm 48 Start/stop button 6X Main station helm 53 All start/stop button 6X C0 For single/twin/triple engine application 7-29

263 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE QUAD ENGINE APPLICATION (FOR F/LF225CA, F/LF250CA, F/LF300CA, F/LF350CA/) 37 P/CP CS/S (*1) (*1) For 2nd station helm (*2) (*2) For 2nd station helm 10 US (50) (50) (50) (50) US (+) (GND) GPS PTT SW A C D E F

264 A C D E F (*4) (*4) (*3) To NMEA2000 Network To NMEA2000 Network (*3) Fuel tank 1 (*5) (*5) Sewage tank 1 1 Fuel tank 2 Freshwater tank ECM ECM ECM ECM (*1) For previous digital electronic controlled engine (*2) For previous network system (6Y8) (*3) Engine selection for tachometer PORT engine C-PORT engine C-STD engine STD engine P CP CS S (*4) Requires 2 pcs including its related parts (*5) Connect the sensor ground leads to the ground (negative circuit on the battery) 7-31

265 NETWORK WIRING DIAGRAMS SINGLE STATION W/ 6Y9 GAUGE QUAD ENGINE APPLICATION (FOR F/LF225CA, F/LF250CA, F/LF300CA, F/LF350CA/) Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 2 Conversion harness 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 7 Conversion harness L 6X6-8258A-L m (0.5 ft) 8 Twinning harness 6X6-8258A-U0 0.1 m (0.3 ft) 10 GPS wire 6Y9-8356N m (1 ft) 11 Tank wire 6Y9-8356N m (1 ft) 12 Main bus wire 13 Pigtail bus wire 14 System power supply wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 10-amp fuse, 2.4 m (8 ft) Ref. No. 16 Multi-hub 6Y w/ resistor cap, lack 17 Single (inline) hub 6Y w/ resistor, 4-6P, White 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 6X6 binnacle mount Digital Electronic Control 6Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) 6X Depth, speed, water temp, w/ 4.9 m (15 ft) wire Single & dual station/ Main station helm 50 Main switch 6X M2 Main station helm, P/CP/CS/S 56 Engine shut-off switch 6X V0 For quad engine application 7-32

266 MEMO

267 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For previous network system (6Y8) (*3) Engine selection for tachometer (*4) Connect the sensor ground leads to the ground (negative circuit on the battery) ECM (*1) Sewage tank Freshwater tank Fuel tank 2 Fuel tank 1 16 (*1) (*4) (*3) (*2) To NMEA2000 Network (*3) 2nd station helm Main station helm 10 4 US (+) (GND) GPS

268 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE SINGLE ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 3 Conversion harness 1 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 14 System power supply wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 10-amp fuse, 2.4 m (8 ft) 16 Multi-hub 6Y w/ resistor cap, lack 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 Depth, speed, water temp, w/ 4.9 m (15 ft) wire Ref. No. 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 2nd station helm harness (2-12P) 2nd station helm harness (3/4/6P) 6X6 binnacle mount Digital Electronic Control 6X6 binnacle mount Digital Electronic Control 6Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) 6X6-8258A-1 5 m (16 ft) 6X6-8258A-D1 8 m (26 ft) 6X6-8258A-F1 12 m (38 ft) 6X6-8258A-G1 5 m (16 ft) 6X6-8258A-H1 8 m (26 ft) 6X6-8258A-J1 12 m (38 ft) 6X Dual station/main station helm 6X Dual station/2nd station helm For 6X6 binnacle mount Digital 40 Main switch 6X Electronic Control, Main station helm 41 Start/stop button 6X nd station helm 42 Engine shut-off switch 6X nd station helm 54 Station selector switch 6X For dual station, single/twin/ triple engine application 7-35

269 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For 6Y9 network system ECM (*1) 28 Fuel tank (*1) TACH (*2) nd station helm SPEED Main station helm TACH SPEED/FUEL 22 (GND) (+) Not used GPS 7-36

270 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y8 GAUGE SINGLE ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 9 Fuel tank/gps wire 6Y8-8356N m (1 ft) 12 Main bus wire 13 Pigtail bus wire 14 System power supply wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 10-amp fuse, 2.4 m (8 ft) Ref. No. 16 Multi-hub 6Y w/ resistor cap, lack 19 Transom multi-sensor 6Y Immobilizer unit Part name Part No. Remarks 2nd helm harness (2-12P) 2nd helm harness (3/4/6P) 6X6 binnacle mount Digital Electronic Control 6X6 binnacle mount Digital Electronic Control 6Y EU 6Y US, ANZ 6Y JP 6X6-8258A-1 5 m (16 ft) 6X6-8258A-D1 8 m (26 ft) 6X6-8258A-F1 12 m (38 ft) 6X6-8258A-G1 5 m (16 ft) 6X6-8258A-H1 8 m (26 ft) 6X6-8258A-J1 12 m (38 ft) Depth, speed, water temp, w/ 4.9 m (15 ft) wire 6X Dual station/main station helm 6X Dual station/2nd station helm 6X6 binnacle mount Digital 40 Main switch 6X Electronic Control, Main station helm 41 Start/stop button 6X nd station helm 42 Engine shut-off switch 6X nd station helm 54 Station selector switch 6X For dual station, single/twin/ triple engine application 7-37

271 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE TWIN ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For previous network system (6Y8) (*3) Engine selection for tachometer PORT engine STD engine (*4) Requires 2 pcs including its related parts (*5) Connect the sensor ground leads to the ground (negative circuit on the battery) P ECM S ECM (*1) Sewage tank Freshwater tank Fuel tank 2 Fuel tank (*4) (*3) (*1) (*2) (*4) To NMEA2000 Network (*3) (*5) 2nd station helm Main station helm US (+) (GND) GPS

272 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE TWIN ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 3 Conversion harness 1 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 15 Immobilizer PWR distribution wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 5-amp fuses, 2.4 m (8 ft) 16 Multi-hub 6Y w/ resistor cap, lack 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 Depth, speed, water temp, w/ 4.9 m (15 ft) wire Ref. No. 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 2nd station helm harness (2-12P) 2nd station helm harness (3/4/6P) 6X6 binnacle mount Digital Electronic Control 6X6 binnacle mount Digital Electronic Control 6Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) 6X6-8258A-1 5 m (16 ft) 6X6-8258A-D1 8 m (26 ft) 6X6-8258A-F1 12 m (38 ft) 6X6-8258A-G1 5 m (16 ft) 6X6-8258A-H1 8 m (26 ft) 6X6-8258A-J1 12 m (38 ft) 6X Dual station/main station helm 6X Dual station/2nd station helm 42 Engine shut-off switch 6X nd station helm 44 Main switch 6X Main station helm 45 Start/stop button 6X Main station helm 46 Start/stop button 6X E0 2nd station helm 53 All start/stop button 6X C0 54 Station selector switch 6X For single/twin/triple engine application For dual station, single/twin/ triple engine application 7-39

273 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y8 GAUGE TWIN ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For 6Y9 network system P ECM S ECM (*1) Fuel tank 2 Fuel tank 1 16 (*1) (*2) TACH TACH nd station helm FUEL MGT SPEED 53 Main station helm TACH FUEL MGT TACH SPEED (GND) (+) GPS

274 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y8 GAUGE TWIN ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 9 Fuel tank/ GPS wire 6Y8-8356N m (1 ft) 12 Main bus wire 13 Pigtail bus wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 16 Multi-hub 6Y w/ resistor cap, lack 19 Transom multi-sensor 6Y Depth, speed, water temp, w/ 4.9 m (15 ft) wire Ref. No. 22 Immobilizer unit Part name Part No. Remarks 2nd helm harness (2-12P) 2nd helm harness (3/4/6P) 6X6 binnacle mount Digital Electronic Control 6X6 binnacle mount Digital Electronic Control 6Y EU 6Y US, ANZ 6Y JP 6X6-8258A-1 5 m (16 ft) 6X6-8258A-D1 8 m (26 ft) 6X6-8258A-F1 12 m (38 ft) 6X6-8258A-G1 5 m (16 ft) 6X6-8258A-H1 8 m (26 ft) 6X6-8258A-J1 12 m (38 ft) 6X Dual station/ Main station helm 6X Dual station/ 2nd station helm 42 Engine shut-off switch 6X nd station helm 44 Main switch 6X Main station helm 45 Start/stop button 6X Main station helm 46 Start/stop button 6X E0 2nd station helm 53 All start/stop button 6X C0 54 Station selector switch 6X For single/twin/triple engine application For dual station, single/twin/ triple engine application 7-41

275 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE TRIPLE ENGINE APPLICATION (*1) For previous digital electronic controlled engine (*2) For previous network system (6Y8) (*3) Engine selection for tachometer PORT engine CENTER engine STD engine (*4) Requires 3 pcs including its related parts (*5) Connect the sensor ground leads to the ground (negative circuit on the battery) P ECM C ECM S ECM (*1) 54 Sewage tank Freshwater tank Fuel tank 2 Fuel tank 1 16 (*1) (*5) (*4) (*3) (*2) (*4) To NMEA2000 Network (*3) 2nd station helm Main station helm US (+) (GND) GPS

276 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE TRIPLE ENGINE APPLICATION Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 3 Conversion harness 1 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 15 Immobilizer PWR distribution wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 5-amps fuses, 2.4 m (8 ft) 16 Multi-hub 6Y w/ resistor cap, lack 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 Depth, speed, water temp, w/ 4.9 m (15 ft) wire Ref. No. 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Part name Part No. Remarks Analog meter trim/oil lead 2nd helm station harness (2-12P) 2nd helm station harness (3/4/6P) 6X6 binnacle mount Digital Electronic Control 6X6 binnacle mount Digital Electronic Control 6Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) 6X6-8258A-1 5 m (16 ft) 6X6-8258A-D1 8 m (26 ft) 6X6-8258A-F1 12 m (38 ft) 6X6-8258A-G1 5 m (16 ft) 6X6-8258A-H1 8 m (26 ft) 6X6-8258A-J1 12 m (38 ft) 6X X Single & dual station/main station helm Single & dual station/2nd station helm 42 Engine shut-off switch 6X nd station helm 47 Main switch 6X Main station helm 48 Start/stop button 6X Main station helm 49 Start/stop button 6X F0 2nd station helm 53 All start/stop button 6X C0 54 Station selector switch 6X For single/twin/triple engine application For dual station, single/twin/ triple engine application 7-43

277 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE QUAD ENGINE APPLICATION (FOR F/LF225CA, F/LF250CA, F/LF300CA, F/LF350CA/) 2nd station helm Main station helm US (*3) P/CP CS/S (*1) (*1) 4 (*2) (*2) PTT SW 5 21 (*4) (*4) (*3) P/CP CS/S (*1) (*1) (*2) (*2) PTT SW A US

278 10 (+) (GND) US A (50) (50) (50) (50) US GPS (*4) (*4) (*3) (*3) (*5) To NMEA2000 To NMEA2000 (*5) Network Network 1 1 Fuel tank 1 Sewage tank 12 Fuel tank 2 Freshwater tank 6 17 (*1) For previous digital electronic controlled engine (*2) For previous network system (6Y8) (*3) Engine selection for tachometer 19 ECM ECM ECM ECM PORT engine C-PORT engine C-STD engine STD engine P CP CS S (*4) Requires 2 pcs including its related parts (*5) Connect the sensor ground leads to the ground (negative circuit on the battery) 7-45

279 NETWORK WIRING DIAGRAMS DUAL STATION W/ 6Y9 GAUGE QUAD ENGINE APPLICATION (FOR F/LF225CA, F/LF250CA, F/LF300CA, F/LF350CA/) Ref. No. Part name Part No. Remarks 1 Main-harness (16P) 6X6-8258A-10 7 m (23 ft) 6X6-8258A-20 8 m (26 ft) 6X6-8258A m (32 ft) 6X6-8258A m (38 ft) 2 Conversion harness 6Y m (1 ft) 3 Conversion harness 1 6Y m (1 ft) 4 Conversion harness 4 6Y m (0.5 ft) 5 Conversion harness 5 6Y m (0.5 ft) 6 Conversion harness 6 6Y m (0.8 ft) 7 Conversion harness L 6X6-8258A-L m (0.5 ft) 8 Twinning harness 6X6-8258A-U0 0.1 m (0.3 ft) 10 GPS wire 6Y9-8356N m (1.1 ft) 11 Tank wire 6Y9-8356N m (0.9 ft) 12 Main bus wire 13 Pigtail bus wire 14 System power supply wire 6Y m (1 ft) 6Y m (10 ft) 6Y m (15 ft) 6Y m (20 ft) 6Y m (25 ft) 6Y m (30 ft) 6Y m (1 ft) 6Y m (2 ft) 6Y m (3 ft) 6Y m (6 ft) 6Y m (9 ft) 6Y m (12 ft) 6Y w/ 10-amps fuse, 2.4 m (8 ft) 16 Multi-hub 6Y w/ resistor cap, lack 17 Single (inline) hub 6Y w/ resistor, 4-6P, White 18 Premium color gauge 6Y w/ screen cover 19 Transom multi-sensor 6Y NMEA 2000 gateway 6Y9-8A2D Analog gauge interface 6Y9-8A2D0-30 Depth, speed, water temp, w/ 4.9 m (15 ft) wire Ref. No. 6Y EU 22 Immobilizer unit 6Y US, ANZ 6Y JP 23 Analog tachometer 6Y lack panel 6Y White panel 24 Analog trim gauge 6Y lack panel 6Y White panel 25 Analog meter harness 6Y m (8 ft) Analog meter trim/oil lead 2nd station helm harness (2-12P) 2nd station helm harness (3/4/6P) 6X6 binnacle mount Digital Electronic Control 6X6 binnacle mount Digital Electronic Control 6Y m (16 ft) 6Y m (19 ft) 6Y m (23 ft) 6Y m (26 ft) 6Y m (29 ft) 6Y m (34 ft) 6X6-8258A-1 5 m (16 ft) 6X6-8258A-D1 8 m (26 ft) 6X6-8258A-F1 12 m (38 ft) 6X6-8258A-G1 5 m (16 ft) 6X6-8258A-H1 8 m (26 ft) 6X6-8258A-J1 12 m (38 ft) 6X X Single & dual station/main station helm Single & dual station/2nd station helm 50 Main switch 6X M2 Main station helm, P/CP/CS/S 51 Start/stop button 6X J0 2nd station helm, P/CP 52 Start/stop button 6X K0 2nd station helm, S/CS 55 Station selector switch 6X L0 For dual station, quad engine application 56 Engine shut-off switch 6X V0 For quad engine application 57 Part name Part No. Remarks 2nd station helm harness (3-12P) 6X6-8258A-R0 5 m (16 ft) 6X6-8258A-S0 8 m (26 ft) 6X6-8258A-T0 12 m (38 ft) 7-46

280 MEMO

281 ATTERY RECOMMENDED ATTERY ATTERY CALE LENGTH ATTERY WIRING ISOLATOR EQUIPPED MODEL (AOVE 150PS MODEL) EXAMPLE FOR ATTERY CALE WIRING (TWIN ENGINE APPLICATION) RECOMMENDED EXTENSION LENGTH OF ATTERY CALES RECOMMENDED ATTERY SWITCH CAPACITY ATTERY CHARGING CAPAILITY

282 RECOMMENDED ATTERY attery is an important element to ensure proper engine start-up and to maintain engine operation performance. Therefore, exact battery selection is required depending on the model. Read carefully the labels attached to the battery and follow the instruction supplied by battery manufacturer when you treat or maintain the battery. Use the battery charging voltage listed in the table below only as a reference when selecting a battery. The charging voltage may vary depending on the ambient temperature or the electrical load to the battery. NOTICE Do not use a battery which does not meet with the specified capacity. If different battery from the specification is used, the electrical system may perform poorly and/or be overloaded, causing electrical system damage. Do not use a battery which exceeds the maximum CCA rating. If the batteries are used in parallel circuit, use new batteries of the same type and make sure that the total battery rating never exceeds the maximum CCA rating. Select a suitable battery as shown in the table below. 4-STROKE ENGINES Global Model US/CA Model attery charging voltage F8 up to F/FT25 F8 up to F/T V F30 up to F/FL115A Global Model F30 up to F/LF115A US/CA/ANZ Model 15.0 V attery charging voltage F/FL115 F/LF V F/FL150 up to F/FL250 (V6-3.3L) F/LF150 up to F/LF250 (V6-3.3L) 14.5 V attery rating Unit Minimum Maximum CCA/SAE 245 amps 433 amps MCA/AYC 323 amps 520 amps RC/SAE 52 min CCA/EN 347 amps 411 amps 20HR/IEC 40 Ah JIS CCA/SAE 380 amps 1150 amps MCA/AYC 502 amps 1370 amps RC/SAE 124 min CCA/EN 430 amps 1080 amps 20HR/IEC 70 Ah JIS G51 Unit Minimum attery rating Maximum CCA/SAE 380 amps 1150 amps MCA/AYC 502 amps 1370 amps RC/SAE 124 min CCA/EN 430 amps 1080 amps 20HR/IEC 70 Ah JIS G51 CCA/SAE 512 amps 1150 amps MCA/AYC 675 amps 1370 amps RC/SAE 124 min CCA/EN 510 amps 1080 amps 20HR/IEC 80 Ah JIS 80D26 195G51 8-2

283 Global Model F150C, F165A, F175A, F/FL200 (L4-2.8L), F/FL200 up to F/FL300 (V6-4.2L) US/CA/ANZ Model VF150, F175A, F/LF200 (L4-2.8L), VF200/225/250 (VMAX), F/LF225/250/ 300 (V6-4.2L) attery charging voltage 14.5 V F/FL350 F/LF350C 14.7 V Unit Minimum attery rating Maximum CCA/SAE 680 amps 1150 amps MCA/AYC 770 amps 1370 amps RC/SAE 160 min CCA/EN 640 amps 1080 amps 20HR/IEC 80 Ah JIS 105D31 195G51 CCA/SAE 700 amps 1150 amps MCA/AYC 900 amps 1370 amps RC/SAE 170 min CCA/EN 670 amps 1080 amps 20HR/IEC 110 Ah JIS 120E41 195G51 2-STROKE ENGINES Global Model 6 up to 55 (Except E/40X, 55D) E/40X, 55D & Carbureted 60 up to 225 (V6-2.6L) HPDI (V6-2.6L, V6-3.3L) L/250G US/CA Model 6 up to 50 HPDI (V6-2.6L, V6-3.3L) attery charging voltage No maximum limit (*1) 15.0 V E/40X, E/ 60H: No maximum limit (*2) 14.5V Unit Minimum attery rating Maximum CCA/SAE 245 amps 433 amps MCA/AYC 323 amps 520 amps RC/SAE 52 min CCA/EN 347 amps 411 amps 20HR/IEC 40 Ah JIS CCA/SAE 380 amps 610 amps MCA/AYC 502 amps 730 amps RC/SAE 124 min CCA/EN 430 amps 579 amps 20HR/IEC 70 Ah JIS D26 CCA/SAE 512 amps 690 amps MCA/AYC 675 amps 840 amps RC/SAE 182 min CCA/EN 510 amps 610 amps 20HR/IEC 100 Ah JIS 80D26 120E41 *1. Using maintenance-free sealed and/or gel cell batteries are not recommended, because they may not be compatible with Yamaha s charging system for these models. *2. Using maintenance-free sealed and/or gel cell batteries are not recommended, because they may not be compatible with the charging system for E/40X and E60H. CCA: Cold Cranking Ampere SAE: Society of Automotive Engineers MCA: Marine Cranking Ampere AYC: American oat and Yacht Council RC: Reserve Capacity Minutes EN: European Norm (European Standard) IEC: International Electro-technical Commission JIS: Japanese Industrial Standard 8-3

284 ATTERY CALE LENGTH The following table shows the battery cable length to the ( ) terminal from the grommet of outboard motor. The (+) terminal is usually 100 mm (4 inches) longer than the ( ) terminal. Conductor crosssectional area Remarks Cable length (L) Global Model US/CA Model m ft AWG mm 2 E40J, EK40J V, 50H, FT50C, F50D F30, F40F F30A, F40A US, CA, ANZ & JP: 2.24 m (7.3 ft) E/40X, 9.9F, 15F F20D, F25D F25A/ JP: 2.08 m (6.7 ft) FT25F T25A E/25, E/30H, 30D C, 8C, 20D, 25N, F8C, FT8D F8A F15C, F20 F15A, F20A F, ANZ: 2.38 m (7.8 ft) 75C, 90A F70A, F40G F70A F40H, F50H, FT50J, F60F, FT60G F50, T50, F60, T US, CA: 2.29 m (8 ft) 115, Carbureted V6-2.6L w/ oil injection Carbureted V6-2.6L w/ oil injection HPDI V6-2.6L HPDI V6-2.6L FT8D (RC) F9.9J, FT9.9L F9.9, T JP: 1.85 m (6 ft) E115A F75, F80, F90, F95A, F100, F100D, F75C, F75A, F90A, F/LF115A F/FL115A 115C, L/150A, L/200A L/250G Global Model F/FL150A, F/FL150, F150C, F165A, F175A, F/FL200F, F/FL200G US/CA/ANZ Model F/LF150A, VF150A, F175A, F/LF200, F/FL200G Conductor crosssectional area Cable length (L) m ft AWG mm F/FL115 F/LF F/FL200, F/FL200C, F/ FL225, F225C, F/FL250A, F/ FL250G F200D, F225D, F250C, F225G, F250F, F275A F/FL225F, F/FL250D, F/ FL300 F/LF200A, F/LF225A, F/ LF250A VF200LA, VF225LA, VF250LA F/LF225CA, F/LF250CA, F/LF300CA F/FL350A F/LF350C /0 60 Remarks 8-4

285 100 mm (4 in.) (L) 8-5

286 ATTERY WIRING ISOLATOR EQUIPPED MODEL (AOVE 150PS MODEL) WARNING attery electrolyte is poisonous and dangerous, causing severe burns, etc. It contains sulfuric acid. Avoid contact with skin, eyes, or clothing. Read the safety and maintenance instructions which are accompaniment to your battery. Do not coil and/or loop the battery cable even if the cable has surplus for routing. When using a house battery, recommended the same capacity as the main battery is for cranking the engine. For twin-battery wiring, a battery cable for ( ) terminal connects between the house battery and the main battery. The battery cable size needs to be equivalent to the main battery cable. Appropriate fuse (conforms to AYC E-11) When one battery is used, connect the red cable with large diameter and the isolator cable with small diameter to the (+) terminal. The isolator cable needs to be connected to (+) battery terminal, because an accidental contact of the isolator cable to the ground will form a short circuit and may cause a fire. Depending on the model, an optional isolated charging cable is available for a house battery. Appropriate fuse (conforms to AYC E-11) Part No. 68F J Length 2.7 m 9 ft 3.8 m 13 ft 6CE m 13 ft Conductor cross-sectional area AWG mm Remarks For HPDI, F150 and above * Except F225 F300 offshore (V6-4.2L) For F225, F250, F300 offshore (V6-4.2L) special If plural batteries are used for multi-engine installation, all ( ) terminals should be connected to the same ground. Obey the local over-current protection compliance such as AYC part E-11 for wiring the battery cables and connecting to a conductor. * Follow the local rules and/or regulations if your battery is scrapped. 8-6

287 ATTERY WIRING EXAMPLE FOR ATTERY CALE WIRING (TWIN ENGINE APPLICATION) Isolator cable attery cable (+) attery cable ( ) Motor (S) Fuse Fuse Motor (P) Applicable models: * F150 (2009 and later model) * F175/200 (L4-2.8L) * F200/225 (V6-3.3L) * F200/225/250 (V6-3.3L w/ VCT) (2008 and later models) * F225/250/300 (V6-4.2L) * F350 Main battery (S) House battery Main battery (P) Motor (S) Motor (P) Applicable models: Isolator equipped models Fuse Fuse Main battery (S) House battery (S) House battery (P) Main battery (P) 8-7

288 ATTERY WIRING RECOMMENDED EXTENSION LENGTH OF ATTERY CALES If the battery cables are extended, follow the requirements in the table due to the battery capacity, cable size and atmosphere temperature. The length of extension battery cable means the total length of (+) and ( ) cables. e sure to select an extension battery cable and a terminal that meet AYC requirements or equivalents. Use a best-suited stud to the terminal size. Solder the connection of terminals and cables to prevent them from corroding. Coiling and/or looping battery cables should be inhibited because of a power loss. NOTICE Do not exceed the recommended extension length of battery cable. Otherwise, the electrical system can result in poor performance or damage. Applicable models Carbureted (V6-2.6L) 4-stroke stroke 150 HPDI (V6-2.6L) 4-stroke 150, 165, 175, 200 (L4-2.8L) Atmosphere temperature is 0 C (32 F) and above attery Maximum total extension length Unit Rating AWG4 AWG2 AWG1/0 AWG2/0 20 mm 2 30 mm 2 50 mm 2 60mm 2 CCA/SAE 380 amps MCA/AYC 502 amps RC/SAE 124 min 3.9 m 6.7 m 10.3 m CCA/EN 430 amps (13 ft) (22 ft) (34 ft) 20HR/IEC 70 Ah JIS 65D31 CCA/SAE 512 amps MCA/AYC 675 amps RC/SAE 182 min 6.0 m 10.0 m 16.0 m CCA/EN 711 amps (20 ft) (33 ft) (52 ft) 20HR/IEC 100 Ah JIS 95E41 CCA/SAE 512 amps MCA/AYC 675 amps RC/SAE 182 min 8.3 m 14.2 m 22.0 m CCA/EN 711 amps (27 ft) (47 ft) (72 ft) 20HR/IEC 100 Ah JIS 95E41 CCA/SAE 680 amps MCA/AYC 770 amps RC/SAE 160 min 2.9 m 4.4 m 7.3 m 8.8 m CCA/EN 640 amps (10 ft) (14 ft) (24 ft) (29 ft) 20HR/IEC 80 Ah JIS 105D31 CCA/SAE 800 amps MCA/AYC 960 amps RC/SAE 230 min 3.2 m 4.8 m 8.0 m 9.6 m CCA/EN 750 amps (11 ft) (16 ft) (26 ft) (32 ft) 20HR/IEC 120 Ah JIS 130E41 To be continued. 8-8

289 ATTERY WIRING RECOMMENDED EXTENSION LENGTH OF ATTERY CALES Applicable models Carbureted 250 (V6-3.1L) HPDI (V6-3.3L) 4-stroke 200, 225, 250 (V6-3.3L) 4-stroke VMAX200, 225, 250 (V6-4.2L) F225G, F250F, F275A 4-stroke 225, 250, 300 offshore model (V6-4.2L) 4-stroke 350 Atmosphere temperature is 0 C (32 F) and above attery Maximum total extension length Unit Rating AWG4 AWG2 AWG1/0 AWG2/0 20 mm 2 30 mm 2 50 mm 2 60mm 2 CCA/SAE 512 amps MCA/AYC 675 amps RC/SAE 182 min 5.4 m 9.2 m 14.2 m CCA/EN 711 amps (18 ft) (30 ft) (47 ft) 20HR/IEC 100 Ah JIS 95E41 CCA/SAE 700 amps MCA/AYC 900 amps RC/SAE 220 min 4.2 m 6.3 m 10.5 m 12.6 m CCA/EN 670 amps (12 ft) (21 ft) (35 ft) 42 ft 20HR/IEC 110 Ah JIS 120E41 CCA/SAE 700 amps MCA/AYC 900 amps RC/SAE 220 min 5 m 7.6 m 12.6 m 15.2 m CCA/EN 670 amps (17 ft) (25 ft) (42 ft) (51 ft) 20HR/IEC 110 Ah JIS 120E41 CCA/SAE 800 amps MCA/AYC 960 amps RC/SAE 230 min 5.5 m 8.3 m 13.8 m 16.6 m CCA/EN 750 amps (18 ft) (28 ft) (46 ft) (55 ft) 20HR/IEC 120 Ah JIS 130E41 CCA/SAE 700 amps MCA/AYC 900 amps RC/SAE 170 min 6.4 m 10.0 m 11.8 m CCA/EN 670 amps (21 ft) (33 ft) (39 ft) 20HR/IEC 110 Ah JIS 120E41 To be continued. 8-9

290 ATTERY WIRING RECOMMENDED EXTENSION LENGTH OF ATTERY CALES Applicable models Carbureted (V6-2.6L) Carbureted 250 (V6-3.1L) 4-stroke 115, 150 & VMAX (SHO) (V-4.2L) HPDI (V6-2.6L) HPDI (V6-3.3L) 4-stroke 150 (VMAX), 165, 175, 200 (L4-2.8L) 4-stroke 200, 225, 250 (V6-3.3L) Atmosphere temperature is below 0 C (32 F) attery Maximum total extension length AWG4 AWG2 AWG1/0 AWG2/0 Unit Rating 20 mm 2 30 mm 2 50 mm 2 60mm 2 CCA/SAE MCA/AYC RC/SAE CCA/EN 20HR/IEC JIS CCA/SAE MCA/AYC RC/SAE CCA/EN 20HR/IEC JIS CCA/SAE MCA/AYC RC/SAE CCA/EN 20HR/IEC JIS CCA/SAE MCA/AYC RC/SAE CCA/EN 20HR/IEC JIS 696 amps 856 amps 167 min 711 amps 83 Ah 95D amps 856 amps 167 min 711 amps 83 Ah 95D amps 960 amps 230 min 750 amps 120 Ah 130E amps 856 amps 167 min 711 amps 83 Ah 95D m (9 ft) 3.9 m (13 ft) 1.8 m (5.9 ft) 3.5 m (11 ft) Cannot be extended 4.8 m (16 ft) 6.7 m (22 ft) 2.7 m (8.9 ft) 6 m (20 ft) 7.4 m (24 ft) 10.4 m (34 ft) 4.5 m (14.8 ft) 9.2 m (30 ft) 5.4 n (17.7 ft) To be continued. 8-10

291 ATTERY WIRING RECOMMENDED EXTENSION LENGTH OF ATTERY CALES Applicable models 4-stroke 225, 250, 300 offshore model (V6-4.2L) 4-stroke 350 Atmosphere temperature is below 0 C (32 F) attery Maximum total extension length Unit Rating AWG4 AWG2 AWG1/0 AWG2/0 20 mm 2 30 mm 2 50 mm 2 60mm 2 CCA/SAE 700 amps MCA/AYC 900 amps RC/SAE 220 min 2.1 m 3.2 m 5.3 m 6.4 m CCA/EN 670 amps (7 ft) (11 ft) (18 ft) (21 ft) 20HR/IEC 110 Ah JIS 120E41 CCA/SAE 800 amps MCA/AYC 960 amps RC/SAE 230 min 2.3 m 3.5 m 5.8 m 7 m CCA/EN 750 amps (8 ft) (12 ft) (19 ft) (23 ft) 20HR/IEC 120 Ah JIS 130E41 CCA/SAE 700 amps MCA/AYC 900 amps RC/SAE 170 min 2.9 m 4.4 m 5.2 m CCA/EN 670 amps (9 ft) (15 ft) (16 ft) 20HR/IEC 110 Ah JIS 120E41 CCA/SAE 800 amps MCA/AYC 960 amps RC/SAE 230 min 3.1 m 4.7 m 5.7 m CCA/EN 750 amps (10 ft) (15 ft) (18 ft) 20HR/IEC 120 Ah JIS 130E41 AWG CCA SAE MCA AYC RC EN IEC JIS : American Wire Gauge, **mm 2 : Conductor cross-section : Cold Cranking Ampere : Society of Automotive Engineers : Marine Cranking Ampere : American oat and Yacht Council : Reserve Capacity Minutes : European Norm (European Standard) : International Electro-technical Commission : Japanese Industrial Standard attery attery Switch ON OFF Extension attery Cable Original attery Cable 8-11

292 ATTERY WIRING RECOMMENDED ATTERY SWITCH CAPACITY Select a battery switch which covers the starting ampere given in the table. If the battery cable connection points are increased, electric resistance will increase and performance for starting will decrease. If a lot of connections such as an automatic battery distribution system is used, the total electric resistance of connections has to be 0.5 MΩ or less. (reference) Applicable models Starting current (Amperes) Carbureted (2.6L) 195 F115A 260 F HPDI (2.6L) 216 F200 F250 (3.3L) 220 HPDI (3.3L) 254 F F150, F165, F175, F200 (2.8L) 200 F350 (V8) 410 F200 F300 (4.2L) 250 Starting current (Amperes) A Hr ATTERY CHARGING CAPAILITY The following chart shows the net capability to charge a battery. In case of an isolator equipped model, the capability is the total of main and isolator lines. * When the temperature of stator coil has risen, the battery charging capability tends to drop. Global model US/CA model Net capability Note F25D, FT25F, F20D F25A, T25A/ 13 amps F30, F40F F30A, F40A 13 amps F70A, F40G F70A 8.5 amps F40H, F50H, FT50J, F60F, FT60G F50, T50, F60, T60 9 amps F75, F75C, F80, F90, F100D F75A, F90A 19 amps F/FL115A F/LF115A 16 amps Global model US/CA/ANZ model Net capability Note F/FL115 F/LF amps F/FL150A, F/FL150 F/LF150A 21 amps F/FL200, F/FL200C, F/FL225, F225C, F/FL250A, F/FL250, F/FL250G F200D, F225D, F250C, F225G, F250F, F275A F150C, F165A, F175A, F/FL200F, F/FL200G F/FL225F, F/FL250D, F/FL300 F/LF115, F/LF200A, F/LF225A, F/LF250A 27 amps V6-3.3L (VCT) VF200LA, VF225LA, VF250LA 35 amps VMAX (SHO) VF150A, F175A, F/LF200, F/LF200CA F/LF225CA, F/LF250CA, F/LF300CA 42 amps L4-2.8L 55 amps V6-4.2L F/FL350A F/LF350C 33 amps V8-5.3L 8-12

293 MEMO

294 APPENDIX MODEL NAME DESIGNATION GLOAL MODELS IDENTIFICATION CODE US & CANADA MODELS IDENTIFICATION (CODE) US & CANADA NEW MODELS IDENTIFICATION CODE FUEL SYSTEM VACUUM PRESSURE STANDARD FUEL HOSE ROUTING RESISTANCE MEASURING METHOD LOWEST VACUUM PRESSURE STANDARD PORTALE FUEL TANKS (TYPICAL) FUEL PIPES (TYPICAL) PRIMARY PUMP (TYPICAL) PRE-DELIVERY INSPECTION (PDI) CONVENTIONAL RIGGING KIT CONTENTS DIGITAL TACHOMETER KIT DIGITAL TACHOMETER AND SPEEDOMETER KIT TWIN-MOTOR KIT REMOTE OIL TANK KIT (FOR 2-STROKE ENGINE) DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS SQUARE/ROUND STYLE GAUGE RIGGING KIT CONTENTS FOR US AND CANADA SQUARE STYLE GAUGE RIGGING KIT FOR EUROPE ROUND STYLE GAUGE RIGGING KIT FOR EUROPE SQUARE STYLE GAUGE RIGGING KIT FOR ANZ SQUARE STYLE GAUGE RIGGING KIT FOR ANZ SQUARE STYLE GAUGE RIGGING KIT FOR JAPAN ROUND STYLE GAUGE RIGGING KIT FOR JAPAN IMMOILIZER RIGGING KIT CONTENTS IMMOILIZER KIT 1 (FOR US, ANZ, CR) IMMOILIZER KIT 2 (FOR JPN) SINGLE ENGINE GAUGE KIT FOR IMMOILIZER (FOR EU, ANZ, JPN, GEN) TWIN ENGINE GAUGE KIT FOR IMMOILIZER To be continued. 9-1

295 APPENDIX DIGITAL NETWORK PREMIUM GAUGE RIGGING KIT CONTENTS SINGLE ENGINE PREMIUM GAUGE KIT ADDITIONAL PREMIUM GAUGE KIT (EU, ANZ, GEN) TWIN ENGINE PREMIUM GAUGE KIT TRIPLE ENGINE PREMIUM GAUGE KIT (FOR EU, ANZ, GEN) MAIN HELM SW PANEL TWIN ENGINE KIT (FOR US, CAN) MAIN HELM SW PANEL TRIPLE ENGINE KIT (FOR US, CAN) ND HELM SW PANEL SINGLE ENGINE KIT (FOR US, CAN) ND HELM SW PANEL TWIN ENGINE KIT (FOR US, CAN) ND HELM SW PANEL TRIPLE ENGINE KIT (FOR US, CAN) OTHER RIGGING KIT CONTENTS TILT LIMIT SWITCH KIT (FOR US, CA, EU, ANZ, RUS, JPN) TILT LIMIT SWITCH KIT 2 (FOR US, CA, EU, ANZ, JP, RUS, TUR) TILT LIMIT SWITCH KIT 3 (FOR US, CA, EU, ANZ, JP, RUS, TUR) TILT LIMIT SWITCH KIT 4 (FOR US, CA, EU, ANZ, JP, RUS, TUR) LIGHTING COIL KIT (FOR EU, CA, JPN) YEAR MODELS MANUFACTURE STARTING SERIAL NUMERS

296 MODEL NAME DESIGNATION The model primary ID that consists of the model name, prefix model code, transom length and serial number is stamped on the label attached to the clamp bracket. * The serial number is a 7-digit sequential numbering scheme irrespective of model variation and transom length. GLOAL MODELS IDENTIFICATION CODE Prefix model code Transom height 6AX Model name FL350AET U YAMAHA MOTOR CO., LTD. MADE IN JAPAN PAYS D'ORIGINE JAPON Serial number The model identification has been standardized as follows since 1998 model year. FL 350 A ET U Model category Non: 2-stroke STD engine D: Twin rotating prop E: Enduro series F: 4-stroke engine K: Kerosene engine L: L/H rotation series T: High thrust (4-stroke) Z: HPDI engine Output (PS) 2 to 350 Model generation A C D F G H J L N P Q R S T U V X Y (Repeat from A) Model variation Level 1: Start system M: Manual start E: Electric start W: Electric & Manual start Level 2: Control system lank: Remote control H: Tiller handle C: Remote control w/ tiller handle Level 3: Trim & Tilt system lank: Manual tilt D: Hydro tilt P: Power tilt T: Power trim & tilt Level 4: Lubrication system [2-stroke engine] lank: Premixed fuel engine O: Oil injection engine Transom height (Drive shaft length) S (15 ) L (20 ) Y (22.5 ) X (25 ) U (30 ) 9-3

297 MODEL NAME DESIGNATION US & CANADA MODELS IDENTIFICATION (CODE) Prefix model code Transom height 6G Model name F40LEHA L YAMAHA MOTOR CO., LTD. MADE IN JAPAN PAYS D'ORIGINE JAPON Serial number US & CANADA NEW MODELS IDENTIFICATION CODE The model codes for the current US and Canada models are described in a simplified form as shown below. For Australia and New Zealand, the same model codes as US and Canada models are used for 4- stroke 150HP and larger models. For the model codes for previous models, see 2013 Rigging Guide or earlier editions. F 40 L E H A Model category F: 4-stroke model L: L/H rotation model V: VMAX series T: High thrust model Power output Driveshaft length S: 15 L: 20 X: 25 U: 30 J: Jet drive N: Without lowercase Starting method PT/T Control method Model generation lank: PTT & E-start P: PT & E-start E: Electric start M: Manual start lank: Remote control H: Tiller handle C: Command Link Control (DEC) A: New model (1st change on motor) : 2nd change on motor C: 3rd change on motor etc. 9-4

298 FUEL SYSTEM VACUUM PRESSURE STANDARD In high-horsepower V6 models, the required fuel flow volume at normal operation may become insufficient and the engine s reliability may decrease, due to the routing resistance of the fuel hoses and the installation of a larger fuel filter. For the fuel hose routing standard, be sure to consult the service network as well as the boat manufactures. FUEL HOSE ROUTING RESISTANCE MEASURING METHOD (2) Short clear hose to fuel filter Hose to gauge (1) (3) (4) Hose to fuel pump (5) No. Description Part No. Q ty Remark (1) HOSE JOINT 6E (2) HOSE Commercially obtainable 1 50 mm (2.0 in.) clear hose (inside diameter is 8 mm (0.3 in)) used to check for air bubbles (3) HOSE 61A L = 300 mm (11.8 in.) (250 to 400 mm (9.8 to 15.7 in.) is acceptable) (4) CLAMP (5) VACUUM PRES- SURE GAUGE Commercially obtainable 1 Specified pressure range: 101 kpa ( 760 mmhg) to 0 1. Connect a 50 mm (2.0 in.) clear hose (market obtainable) (2) to the top nipple of the hose joint (1). 2. Connect the other end of the clear hose (2) to the engine fuel filter outlet. 3. Connect the fuel hose (3) to the center nipple of the hose joint, and the other end of the fuel hose to a vacuum gauge (commercially obtainable) (5). 4. Connect the fuel pump hose to the hose joint, and then fasten all hose connections with clamps (4). 5. Start the engine, let it warm up, and then measure the vacuum pressure at idle and wide-open throttle, after the breaking-in period has been completed. 6. Measure and check that the vacuum pressure is within specification, and then route the fuel hoses to their original positions. 9-5

299 FUEL SYSTEM VACUUM PRESSURE STANDARD LOWEST VACUUM PRESSURE STANDARD The lowest vacuum pressure must be fulfilled as below at an atmospheric temperature of 20 C (68 F) and higher. Idle: 0 kpa to 10.7 kpa ( 80 mmhg) WOT: 10.7 kpa ( 80 mmhg) to 20 kpa ( 150 mmhg) * e sure to measure and check that the vacuum pressure is within specification at idle and wide-open throttle, after the breaking-in period has been completed. Engine breaking-in operating conditions : 10 hours 2-stroke carbureted models : Use 25:1 pre-mixed fuel. 2-stroke electronic fuel injected models : Use 50:1 pre-mixed fuel, and supply with oil injection. HPDI models : Use straight gasoline (only supply with oil injection) 4-stroke models : Use straight gasoline. Larger fuel filters installed onto a boat may lower the fuel vacuum pressure to 20.0 kpa ( 15 mmhg) and under. Therefore, follow the instructions mentioned above to rig the boat properly so that the fuel vacuum pressure is within specification. If the vacuum pressure does not surpass 10.7 kpa ( 80 mmhg) at wide-open throttle, use a clear hose to check that air bubbles are not mixed in the fuel. 9-6

300 PORTALE FUEL TANKS (TYPICAL) 1 mm (in.) 2 mm (in.) 3 mm (in.) 363 (14.3) 265 (10.4) 230 (9.1) 363 (14.3) 265 (10.4) 232 (9.1) 455 (17.9) 252 (9.9) 314 (12.4) 4 mm (in.) 5 mm (in.) 233 (9.2) 536 (21.1) 545 (21.5) 362 (14.3) 362 (14.3) 233 (9.2) No. Part No. Capacity L (US gal) Material Description 1 6YL-W2420-J3 12 (3.2) Plastic w/ fuel gauge 2 6YL (3.2) Plastic US/CA meeting with EPA regulations, w/ fuel gauge 3 6YJ (6.3) Plastic For JPN, With JCI label, w/ fuel gauge 6YJ (6.3) Plastic With tag and exclusive filler structure banning use of leaded fuel (EU) 6YK (6.6) Plastic With fuel gauge 4 6YK (6.6) Plastic With label and exclusive filler structure banning use of leaded fuel 6YK (6.6) Plastic For kerosene 5 6YK (6.6) Plastic US/CA meeting with EPA regulations, w/ fuel gauge 9-7

301 FUEL PIPES (TYPICAL) 1 2 (L) (L) 3 (L) No. Part No. Hose inside diameter Length (L) Remarks 1 6Y mm (0.24 in) 3 m (10 ft) For small engines 2 6YK mm (0.31 in) 3 m (10 ft) US/CA meeting with EPA regulations 3 6YK mm (0.24 in) 3 m (10 ft) For kerosene models PRIMARY PUMP (TYPICAL) Part No. Hose inside diameter Remarks 6YK mm (0.31 in) Meeting with EPA regulations, Above F75 6YL mm (0.24 in) 9-8

302 PRE-DELIVERY INSPECTION (PDI) efore operation, go over the checklist below to enhance customer satisfaction. Fill in the information required. Perform the static and dynamic checks following the items on the sheet. SAMPLE 9-9

303 CONVENTIONAL RIGGING KIT CONTENTS The rigging kit is handled by Marine Sales Division of Yamaha Motor Corporation. Thereby, Yamaha parts distribution center in Japan is not in charge of distribution of the kit. Attention to importers, the rigging kit must be purchased from Sales Division as well as outboardmotors because it is impossible to purchase from the parts route. DIGITAL TACHOMETER KIT US/CA: Above 40, Above F30 Others: Above 40 (3-cyl) w/ oil injection (except 250G & L250G), Above F30 P/N: 6YR-W0035-E3 Part name Part No. Q ty Remarks EXT wire-lead 6Y m (23 ft) Tachometer ASSY 6Y5-8350T-91 1 Included instruction tag Wire-lead 6Y m (8 ft) w/10 amp fuse DIGITAL TACHOMETER AND SPEEDOMETER KIT US/CA: Above 40, Above F30 Others: Above 40 (3-cyl) w/ oil injection (except 250G & L250G), Above F30 P/N: 6YR-W0035-F3 Part name Part No. Q ty Remarks Wire-lead 6Y N m (8 ft) w/10 amp twin-fuse Tachometer ASSY 6Y5-8350T-91 1 Included instruction tag EXT wire-lead 6Y m (26 ft) Speedometer ASSY 6Y S6 1 Included instruction tag Tube 6Y m (26 ft) Clamp M10 2 Clamp M18 10 Instruction 61A A4 1 ANZ: Fuel injected F50-F100 P/N: 6YR-W0035-T1 Part name Part No. Q ty Remarks Wire-lead 6Y cm (1 ft), LK Tachometer ASSY 6Y5-8350T-91 1 Included instruction tag Wire-lead 6Y M m (8 ft) w/10 amp twin-fuse Tube 6Y m (26 ft) Speedometer ASSY 6Y S6 1 Included instruction tag EXT wire-lead 6Y m (26 ft) Clamp M

304 CONVENTIONAL RIGGING KIT CONTENTS TWIN-MOTOR KIT Above L150 (except L250G), Above FL/LF115 P/N: 6YR-W0035-G7 Part name Part No. Q ty Remarks Wire-lead 6Y m (8 ft) w/10 amp fuse Tachometer ASSY 6Y5-8350T-91 1 Includes instruction tag EXT wire-lead 6Y m (31 ft) Twin-binnacle RCL box P1 1 Premium Main wire-harness, 10-pin 6K1-8258A m (26 ft) Main wire-harness, 10-pin A m (32 ft) Clamp M18 10 Twin-switch panel 6K With multi-engine system Screw M mm (0.1 in) Nut Plane washer Spring washer Fuel mgt gauge 6Y5-8350F-01 1 With 3-prong connector Wire-lead 6Y F1 1 8 m (26 ft) Fuel flow sensor 6Y Screw mm (2.7 in) Instruction A

305 CONVENTIONAL RIGGING KIT CONTENTS REMOTE OIL TANK KIT (FOR 2-STROKE ENGINE) 10.5 L (2.8 US-GAL) TANK Global P/N: 6YR-W0035-D2 Part name Part No. Q ty Remarks Remote oil tank ASSY 61A Remote oil tank holder 6E Damper 6E racket 6E Fuel pipe complete 6YK Clamp M07 1 Clamp M10 1 Clamp M11 1 Washer Nut olt US/CA P/N: 6YR-W Part name Part No. Q ty Remarks Remote oil tank ASSY 61A Remote oil tank holder 6E Damper 6E racket 6E Fuel pipe complete 6Y Meeting with AYC requirements Clamp M07 1 Clamp M10 1 Clamp M11 1 Washer Nut olt

306 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS SQUARE/ROUND STYLE GAUGE RIGGING KIT CONTENTS FOR US AND CANADA The above kit is available from Yamaha Motor Corporation, USA. SQUARE STYLE GAUGE RIGGING KIT FOR EUROPE SINGLE KIT (TACH, SPEED/FUEL MGT) Kit P/N: 6YR-W0035-N8 Part No. Part name Q ty Remarks 60V-8A4L1-13 Speed sensor kit 1 Refer to kit contents 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.6 m (2 ft) 2 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Main bus wire, 6.1 m (20 ft) 1 6Y pin cap, WHT 1 For waterproof 6Y SQR comb. speedometer & fuel mgt gauge 1 6Y8-8350T-01 SQR tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y8-2819U-X2 Quick operation guide 1 6Y8-2819K-S1 Quick installation guide 1 6Y8-2819U-20 Operation manual 1 SINGLE KIT (TACH, SPEED/FUEL MGT) w/o Speed Sensor Kit Kit P/N: 6YR-W0035-F0 Part No. Part name Q ty Remarks 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.6 m (2 ft) 2 6Y Pigtail bus wire, 0.6 m (2 ft) 1 6Y Main bus wire, 6.1 m (20 ft) 1 6Y pin cap, WHT 1 For waterproof 6Y SQR comb. speedometer & fuel mgt gauge 1 6Y8-8350T-01 SQR tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y8-2819U-X2 Quick operation guide 1 6Y8-2819K-S1 Quick installation guide 1 6Y8-2819U-70 Operation manual 1 1 6Y8-2819U-80 Operation manual

307 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS SQUARE STYLE GAUGE RIGGING KIT FOR EUROPE TWIN KIT (TACH, TACH, SPEED, FUEL MGT) Kit P/N: 6YR-W0035-PA Part No. Part name Q ty Remarks 60V-8A4L1-13 Speed sensor kit 1 Refer to kit contents A-01 Main wire-harness 10-pin, 8 m (26 ft) 1 6K1-8258A-40 Main wire-harness 10-pin, 9.8 m (32 ft) 1 6Y Multi-hub 3 With resistor cap, GRY 6Y Pigtail bus wire, 0.6 m (2 ft) 4 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Pigtail bus wire, 2.7 m (9 ft) 1 6Y Main bus wire, 0.3 m (1 ft) 1 6Y Main bus wire, 7.6 m (25 ft) 1 6Y pin cap, RED 2 For waterproof 6Y pin cap, WHT 3 For waterproof 6Y8-8350F-01 SQR fuel mgt gauge 1 6Y8-8350S-01 SQR speedometer 1 6Y8-8350T-01 SQR tachometer 2 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire P1 Twin-binnacle RCL box, Premium 1 6Y Twin-switch panel M05 Screw, 25 mm (1 in) Nut PLN washer SRG washer 4 6Y8-2819U-X2 Quick operation guide 1 6Y8-2819K-S1 Quick installation guide 1 6Y8-2819U-20 Operation manual

308 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS SQUARE STYLE GAUGE RIGGING KIT FOR EUROPE TWIN KIT (TACH, TACH, SPEED/FUEL MGT) w/o Speed Sensor Kit Kit P/N: 6YR-W0035-G0 Part No. Part name Q ty Remarks A-01 Main wire-harness 10-pin, 8 m (26 ft) 1 6K1-8258A-40 Main wire-harness 10-pin, 9.8 m (32 ft) 1 6Y Multi-hub 3 With resistor cap, GRY 6Y Pigtail bus wire, 0.6 m (2 ft) 4 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Pigtail bus wire, 2.7 m (9 ft) 1 6Y Main bus wire, 0.3 m (1 ft) 1 6Y Main bus wire, 7.6 m (25 ft) 1 6Y pin cap, RED 2 For waterproof 6Y pin cap, WHT 3 For waterproof 6Y8-8350F-01 SQR fuel mgt gauge 1 6Y8-8350S-01 SQR speedometer 1 6Y8-8350T-01 SQR tachometer 2 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire P1 Twin-binnacle RCL box, Premium 1 6Y Twin-switch panel M05 Screw, 25 mm (1 in) Nut PLN washer SRG washer 4 6Y8-2819U-X2 Quick operation guide 1 6Y8-2819K-S1 Quick installation guide 1 6Y8-2819U-70 Operation manual 1 1 6Y8-2819U-80 Operation manual 2 1 TWIN KIT (TACH, TACH, SPEED, FUEL MGT) w/o Transom Wire Harness Kit P/N: 6Y8-W Part No. Part name Q ty Remarks 6Y Main bus wire, 0.3 m (1 ft) 1 6Y Pigtail bus wire, 0.6 m (2 ft) 4 6Y Multi-hub 2 With resistor cap, GRY 6Y pin cap, RED 1 For waterproof 6Y pin cap, WHT 2 For waterproof 6Y8-8350T-01 SQR tachometer 2 6Y8-8350S-01 SQR speedometer 1 6Y8-8350F-01 SQR fuel mgt gauge 1 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-2819U-70 Operation manual 1 1 6Y8-2819U-80 Operation manual 2 1 6Y8-2819K-S1 Quick installation guide 1 6Y8-2819U-X2 Quick operation guide

309 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS SQUARE STYLE GAUGE RIGGING KIT FOR EUROPE F350 SINGLE KIT (TACH, SPEED/ FUEL MGT) KIT P/N: 6X6-W Part No. Part name Q ty Remarks 6Y8-8350T-01 Tachometer 1 Square style 6Y8-8356N-01 GPS/ Fuel tank wire 1 6Y Comb. Speed/ fuel mgt gauge 1 Square style 6Y Multi hub 1 6Y Resistor cap 1 Gray, 6-pin 6Y Pigtail bus wire, 0.6 m (2 ft) 2 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6R Switch panel 1 Single 6X6-8258A-30 Main wire harness, 10 m (32 ft) 1 6X6-2819K-S1 Quick installation manual 1 6Y8-2819U-X2 Quick reference guide 1 F350 TWIN KIT (TACH, TACH, SPEED, FUEL MGT) KIT P/N: 6X6-W Part No. Part name Q ty Remarks 6Y8-8350T-01 Tachometer 2 Square style 6Y8-8350S-01 Speedometer 1 Square style 6Y8-8356N-01 GPS/ Fuel tank wire 1 6Y8-8350F-01 Fuel mgt gauge 1 Square style 6Y Multi hub 2 6Y Main bus wire, 0.3 m (1 ft) 1 6Y Pigtail bus wire, 0.6 m (2 ft) 4 6Y Pigtail bus wire, 1.8 m (6 ft) 2 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y P cap, RED 1 For waterproof 6Y Switch panel 1 Twin 6X6-8258A-40 Main wire harness, 12 m (38 ft) 2 6X6-2819K-S1 Quick installation manual 1 6Y8-2819U-X2 Quick reference guide

310 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS ROUND STYLE GAUGE RIGGING KIT FOR EUROPE SINGLE KIT 1 (TACH) Kit P/N: 6YR-W0035-Y3 Part No. Part name Q ty Remarks 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.6m (2 ft) 1 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Main bus wire, 6.1 m (20 ft) 1 6Y pin cap, WHT 2 For waterproof 6Y8-8350T-20 RND tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 6Y8-2819W-70 Owners Manual 1 6Y8-2819W-80 Owners Manual 1 SINGLE KIT 2 (TACH, SPEED/FUEL MGT) w/o Speed Sensor Kit Kit P/N: 6Y8-W0035-E2 Part No. Part name Q ty Remarks 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.6m (2 ft) 2 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Main bus wire, 6.1 m (20 ft) 1 6Y pin cap, WHT 1 For waterproof 6Y RND comb. speedometer & fuel MGT gauge 1 6Y8-8350T-20 RND tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y8-2819W-70 Owners Manual 1 6Y8-2819W-80 Owners Manual

311 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS SQUARE STYLE GAUGE RIGGING KIT FOR ANZ SINGLE KIT (TACH, SPEED, FUEL MGT) Kit P/N: 6YR-W0035-R8 Part No. Part name Q ty Remarks 60V-8A4L1-13 Speed sensor kit 1 Refer to kit contents 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.6 m (2 ft) 3 6Y Pigtail bus wire, 3.6 m (12 ft) 1 6Y Main bus wire, 7.6 m (25 ft) 1 6Y8-8350F-01 SQR fuel mgt gauge 1 6Y8-8350S-01 SQR speedometer 1 6Y8-8350T-01 SQR tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y8-2891U-20 Operation Manual 1 TWIN KIT (TACH) Kit P/N: 6YR-W0035-S3 Requires the single-kit. Part No. Part name Q ty Remarks A-01 Main wire-harness 10-pin, 9.8 m (32 ft) 1 6K1-8258A-40 Main wire-harness 10-pin, 8 m (26 ft) 1 6Y Multi-hub 2 With resistor cap, GRY 6Y Pigtail bus wire, 0.6 m (2 ft) 1 6Y Pigtail bus wire, 3.6 m (12 ft) 1 6Y Main bus wire, 0.3 m (1 ft) 1 6Y pin cap, RED 2 For waterproof 6Y pin cap, WHT 3 For waterproof 6Y8-8350T-01 SQR tachometer P1 Twin-binnacle RCL box, Premium 1 6Y Twin-switch panel M05 Screw, 25 mm (1 in) SRG washer PLN washer Nut 4 6Y8-2891U-20 Operation Manual

312 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS ROUND STYLE GAUGE RIGGING KIT FOR ANZ SINGLE KIT 2 (TACH, SPEED/FUEL MGT) Kit P/N: 6YR-W0035-MC Part No. Part name Q ty Remarks 60V-8A4L1-13 Speed sensor kit 1 Refer to contents 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.6m (2 ft) 2 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Main bus wire, 6.1 m (20 ft) 1 6Y pin cap, WHT 1 For waterproof 6Y RND comb. speedometer & fuel MGT gauge 1 6Y8-8350T-20 RND tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y5-2819K-97 Set up manual 1 6Y8-2819W-70 Owners Manual

313 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS SQUARE STYLE GAUGE RIGGING KIT FOR JAPAN SINGLE KIT 1 (TACH) Kit P/N: 6YR-W0035-U1 Part No. Part name Q ty Remarks 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.9 m (3 ft) 1 6Y Pigtail bus wire, 2.7 m (9 ft) 1 6Y Main bus wire, 6.1 m (20 ft) 1 6Y pin cap, WHT 2 For waterproof 6Y8-8350T-01 SQR tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-2819U-01 Operation manual 1 SINGLE KIT 2 (TACH, SPEED/FUEL MGT) Kit P/N: 6YR-W0035-V7 Part No. Part name Q ty Remarks 60V-8A4L1-13 Speed sensor kit 1 Refer to kit contents 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.9 m (3 ft) 2 6Y Pigtail bus wire, 3.6 m (12 ft) 1 6Y Main bus wire, 7.5 m (25 ft) 1 6Y pin cap, WHT 1 For waterproof 6Y SQR comb. speedometer & fuel mgt gauge 1 6Y8-8350T-01 SQR tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y8-2819U-01 Operation manual 1 F350 SINGLE KIT (TACH, SPEED/ FUEL MGT) Kit P/N: 6X6-W Part No. Part name Q ty Remarks 6Y8-8350T-01 SQR Tachometer 1 6Y8-8356N-01 GPS/ Fuel tank wire 1 6Y SQR Comb. Speed/ fuel mgt meter 1 6Y Multi-hub 1 6Y Resistor cap 1 Gray, 6-pin 6Y Pigtail bus wire, 0.9 m (3 ft) 2 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6R Switch panel 1 Single 6X6-8258A-30 Main wire-harness, 10 m (32 ft) 1 16-pin 6Y8-2819U-01 Operation manual 1 Japanese 9-20

314 DIGITAL NETWORK GAUGE RIGGING KIT CONTENTS ROUND STYLE GAUGE RIGGING KIT FOR JAPAN SINGLE KIT 1 (TACH) Kit P/N: 6YR-W0035-W2 Part No. Part name Q ty Remarks 6Y Multi-hub 1 With resistor cap, GRY 6Y Single-hub 1 With resistor 6Y Pigtail bus wire, 0.9 m (3 ft) 1 6Y Pigtail bus wire, 2.7 m (9 ft) 1 6Y Main bus wire, 6.1 m (20 ft) 1 6Y pin cap, WHT 2 For waterproof 6Y8-8350T-20 RND tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-2819W-00 Owners Manual 1 SINGLE KIT 2 (TACH, SPEED/FUEL MGT) Kit P/N: 6YR-W0035-X8 Part No. Part name Q ty Remarks 60V-8A4L1-13 Speed sensor kit 1 Refer to contents 6Y Multi-hub 1 6Y Single-hub 1 6Y Pigtail bus wire, 0.9 m (3 ft) 2 6Y Pigtail bus wire, 3.6 m (12 ft) 1 6Y Main bus wire, 7.6 m (25 ft) 1 6Y pin cap, WHT 1 For waterproof 6Y RND comb. speedometer & fuel MGT gauge 1 6Y8-8350T-20 RND tachometer 1 6Y PWR supply wire, 2.4 m (8 ft) 1 With 10 amp fuse 6Y8-8356N-01 Fuel tank & GPS wire 1 6Y5-2819K-97 MANUAL,SET UP 1 6Y8-2819W-00 MANUAL,OWNERS

315 IMMOILIZER RIGGING KIT CONTENTS IMMOILIZER KIT 1 (FOR US, ANZ, CR) Kit P/N: 6Y8-W Part No. Part name Q ty Remarks 6Y Immobilizer unit 1 Conformed to local frequency band M00 Screw Screw M30 Washer Nut 4 6Y Pigtail bus wire m (1 ft) 6Y Symbol graphic 4 6Y Instruction 1 IMMOILIZER KIT 2 (FOR JPN) Kit P/N: 6Y8-W Part No. Part name Q ty Remarks 6Y Immobilizer unit 1 Conformed to local frequency band M00 Screw Screw M30 Washer Nut 4 6Y Pigtail bus wire m (1 ft) 6Y Symbol graphic 3 6Y Instruction 1 SINGLE ENGINE GAUGE KIT FOR IMMOILIZER (FOR EU, ANZ, JPN, GEN) P/N: 6Y8-W0035-A2 (w/ IG SW panel) Part No. Part name Q ty Remarks 6Y8-8350T-01 SQR tachometer 1 6Y SQR speed/fuel gauge 1 6Y Multi-hub 2 w/ resistor 6Y Main bus wire, 0.3 m (1 ft) 1 6Y pin waterproof cap 3 White 6Y pin waterproof cap 1 Red 6Y Pigtail bus wire, 0.6 m (2 ft) 2 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y8-8356N-01 Fuel tank/ GPS wire 1 NMEA0183 6Y PWR supply wire 1 w/ 10 amp fuse 6X IG switch panel, single 1 OFF-ON-START 6X6-8258A-30 Main wire-harness, 10 m (33 ft) 1 16-pin 6Y9-2819K-E0 Set up manual 1 6Y8-2819U-20 Operation Manual

316 IMMOILIZER RIGGING KIT CONTENTS SINGLE ENGINE GAUGE KIT FOR IMMOILIZER (FOR EU, ANZ, JPN, GEN) P/N: 6Y8-W0035-D1 (w/o IG SW panel) Part No. Part name Q ty Remarks 6X6-8258A-30 Main wire-harness, 10 m (33 ft) 1 16-pin 6Y Multi-hub 2 6Y Pigtail bus wire, 0.6 m (2 ft) 2 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Main bus wire, 0.3 m (1 ft) 1 6Y pin waterproof cap 1 Red 6Y pin waterproof cap 3 White 6Y SQR speed/fuel gauge 1 NMEA0183 6Y8-8350T-01 SQR tachometer 1 6Y PWR supply wire 1 w/ 10 amp fuse 6Y8-8356N-01 Fuel tank/gps wire 1 6Y9-2819K-E0 Set-up manual 1 6Y8-2819U-70 Operation Manual 1 1 6Y8-2819U-80 Operation Manual 2 1 TWIN ENGINE GAUGE KIT FOR IMMOILIZER P/N: 6Y8-W Part No. Part name Q ty Remarks 6Y8-8350T-01 SQR tachometer 2 6Y8-8350F-01 SQR fuel MGT gauge 1 6Y8-8350S-01 SQR speedometer 1 6Y Multi-hub 3 w/ resistor 6Y Main bus wire, 0.3 m (1 ft) 2 6Y pin waterproof cap 3 White 6Y pin waterproof cap 2 Red 6Y Pigtail bus wire, 0.6 m (2 ft) 4 6Y Pigtail bus wire, 1.8 m (6 ft) 2 6Y8-8356N-01 Fuel tank/gps wire 1 NMEA0183 6Y PWR supply wire 1 w/ 10 amp fuse 6X IG switch, twin 1 OFF-ON 6X Start/stop SW, twin 1 6X6-8258A-40 Main wire-harness, 12.2 m (40 ft) 2 16-pin 6Y9-2819K-E0 Set up manual 1 6Y8-2819U-70 Operation Manual 1 1 6Y8-2819U-80 Operation Manual

317 DIGITAL NETWORK PREMIUM GAUGE RIGGING KIT CONTENTS SINGLE ENGINE PREMIUM GAUGE KIT P/N: 6Y9-W (w/ IG SW panel) Part No. Part name Q ty Remarks 6Y Premium gauge ASSY 1 5" color display, w/ screen cover 6Y Multi-hub 1 w/ resistor cap 6Y pin waterproof cap 2 White 6Y Main bus wire, 0.3 m (1 ft) 1 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Conversion harness 4, 0.15 m (0.5 ft) 1 Hub to premium gauge 6Y Conversion harness, 0.3 m (1 ft) 1 RC to hub 6Y PWR supply wire 1 w/ 10 amp fuse 6Y9-8356N-01 GPS wire 1 NMEA0183 6Y9-8356N-10 Fuel tank wire 1 4 fuel tanks 6X IG switch panel, single 1 OFF-ON-START 6X6-8258A-30 Main wire-harness, 10 m (33 ft) 1 16-pin 6Y9-2819K-E0 Set up manual 1 6Y9-2819U-72 Instruction 2 1 6Y9-2819U-82 Instruction 3 1 P/N: 6Y9-W (w/o IG SW panel) Part No. Part name Q ty Remarks 6X6-8258A-30 Main wire-harness, 10 m (33 ft) 1 16-pin 6Y Multi-hub 1 w/ resistor cap 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Main bus wire, 0.3 m (1 ft) 1 6Y pin waterproof cap 2 White 6Y PWR supply wire 1 w/ 10 amp fuse 6Y9-2819K-E0 Set up manual 1 6Y Conversion harness, 0.3 m (1 ft) 1 RC to Hub 6Y Conversion harness 4, 0.15 m (0.5 ft) 1 Hub to premium gauge 6Y9-8356N-01 GPS wire 1 NMEA0183 6Y9-8356N-10 Fuel tank wire 1 4 fuel tanks 6Y Premium gauge ASSY 1 5" color display, w/ screen cover 6Y9-2819U-72 Instruction 2 1 6Y9-2819U-82 Instruction 3 1 ADDITIONAL PREMIUM GAUGE KIT (EU, ANZ, GEN) P/N: 6Y9-W Part No. Part name Q ty Remarks 6Y Premium gauge ASSY 1 5" color display, w/ screen cover 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Conversion harness, 0.15 m (0.5 ft) 1 Hub to premium gauge 9-24

318 DIGITAL NETWORK PREMIUM GAUGE RIGGING KIT CONTENTS TWIN ENGINE PREMIUM GAUGE KIT P/N: 6Y9-W Part No. Part name Q ty Remarks 6Y Premium gauge ASSY 1 5" color display, w/ screen cover 6Y Multi-hub 1 w/ resistor cap 6Y pin waterproof cap 2 White 6Y Main bus wire, 0.3 m (1 ft) 1 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Conversion harness, 0.15 m (0.5 ft) 1 Hub to premium gauge 6Y Conversion harness, 0.3 m (1 ft) 1 RC to hub 6Y PWR supply wire 1 w/ 10 amp fuse 6Y9-8356N-01 GPS wire 1 NMEA0183 6Y9-8356N-10 Fuel tank wire 1 4 fuel tanks acceptable 6X IG switch, twin 1 OFF-ON 6X Start/stop SW, twin 1 6X6-8258A-40 Main wire-harness, 12.2 m (40 ft) 2 16-pin 6Y9-2819K-E0 Set up manual 1 6Y9-2819U-72 Instruction 2 1 6Y9-2819U-82 Instruction 3 1 TRIPLE ENGINE PREMIUM GAUGE KIT (FOR EU, ANZ, GEN) P/N: 6Y9-W Part No. Part name Q ty Remarks 6X6-2819K-E0 Setup manual 1 6X IG switch panel, Main helm 1 6X Start/stop SW panel, Main helm 1 6X6-8258A-40 Main wire-harness, 12.2 m (40 ft) 3 16-pin 6Y Multi-hub 1 6Y Pigtail bus wire, 1.8 m (6 ft) 1 6Y Main bus wire, 0.3 m (1 ft) 1 6Y pin waterproof cap 2 White 6Y PWR supply wire 1 w/ 10 amp fuse 6Y Conversion harness, 0.3 m (1 ft) 1 RC to hub 6Y Conversion harness, 0.15 m (0.5 ft) 1 Hub to premium gauge 6Y9-8356N-01 GPS wire 1 NMEA0183 6Y9-8356N-10 Fuel tank wire 1 4 fuel tanks acceptable 6Y Premium gauge ASSY 1 5" color display, w/ screen cover 6Y9-2819U-71 Instruction 2 1 6Y9-2819U-81 Instruction 3 1 MAIN HELM SW PANEL TWIN ENGINE KIT (FOR US, CAN) P/N: 6X6-W Part No. Part name Q ty Remarks 6X IG switch, twin 1 OFF-ON 6X Start/stop SW, twin

319 DIGITAL NETWORK PREMIUM GAUGE RIGGING KIT CONTENTS MAIN HELM SW PANEL TRIPLE ENGINE KIT (FOR US, CAN) P/N: 6X6-W Part No. Part name Q ty Remarks 6X IG switch, triple 1 OFF-ON 6X Start/stop SW, triple 1 2ND HELM SW PANEL SINGLE ENGINE KIT (FOR US, CAN) P/N: 6X6-W Part No. Part name Q ty Remarks 6X Start/stop SW, single 1 6X Station selector SW 2 6X Emergency stop SW 1 2ND HELM SW PANEL TWIN ENGINE KIT (FOR US, CAN) P/N: 6X6-W Part No. Part name Q ty Remarks 6X E0 Start/stop SW, twin 1 6X Station selector SW 2 6X Emergency stop SW 1 2ND HELM SW PANEL TRIPLE ENGINE KIT (FOR US, CAN) P/N: 6X6-W Part No. Part name Q ty Remarks 6X F0 Start/stop SW, triple 1 6X Station selector SW 2 6X Emergency stop SW

320 OTHER RIGGING KIT CONTENTS TILT LIMIT SWITCH KIT (FOR US, CA, EU, ANZ, RUS, JPN) P/N: 63P-825EY-01 Applicable models: Global model F/FL115A US/CA model F/LF115A Global model F/FL115 F/FL150A F150C F165A F175A F200D F/FL200F F225D US/CA/ANZ model F/LF115 F/LF150A VF150A VF200LA F/LF200 VF225LA Global model F250C F225G F250F F275A US/CA/ANZ model VF250LA Kit contents: Part No. Part name Q ty Remarks 63P-825E0-01 Tilt limit SW ASSY olt w/ washer Screw Collar M10 Clamp 5 * For installation, see the service manual and/or installation manual. TILT LIMIT SWITCH KIT 2 (FOR US, CA, EU, ANZ, JP, RUS, TUR) P/N: 6CE-825EY-00 Applicable models: Global model F/FL200G F/FL225F F/FL250D F/FL300 US/CA/ANZ model F/LF200CA F/LF225CA F/LF250CA F/LF300CA Kit contents: Part No. Part name Q ty Remarks 6CE-825E0-00 Tilt limit SW ASSY olt w/ washer Screw Collar M10 Clamp M18 Clamp 1 * For installation, see the service manual and/or installation manual. 9-27

321 OTHER RIGGING KIT CONTENTS TILT LIMIT SWITCH KIT 3 (FOR US, CA, EU, ANZ, JP, RUS, TUR) P/N: 6D8-825EY-00 Applicable models: Global model F75 F80 F90 F100D US/CA Model F75A F90A Kit contents: Part No. Part name Q ty Remarks 6D8-825E0-00 Tilt limit SW ASSY olt w/ washer Screw Collar M10 Clamp 4 * For installation, see the service manual and/or installation manual. TILT LIMIT SWITCH KIT 4 (FOR US, CA, EU, ANZ, JP, RUS, TUR) P/N: 6C5-825EY-00 Applicable models: Global model F40G F40H F50H FT50J F60F FT60G F70A US/CA model F50 T50 F60 T60 F70A Kit contents: Part No. Part name Q ty Remarks 6C5-825E0-00 Tilt limit SW ASSY M88 olt Washer Screw Collar M10 Clamp M18 Clamp 3 * For installation, see the service manual and/or installation manual. 9-28

322 OTHER RIGGING KIT CONTENTS LIGHTING COIL KIT (FOR EU, CA, JPN) P/N: 6X-W8130-A0 Applicable models: Global model F4 F5A F6C US/CA Model F4A F6A Kit contents: Part No. Part name Q ty Remarks 6X Wire lead 1 6X Rectifier/ regulator 1 6X Plate 1 6X Stay 1 6X A0 Stator ASSY 1 6X A0 Rotor ASSY M80 olt Clamp Clamp olt olt 3 * For installation, see the service manual and/or service guide. 9-29