Form No Revision A October Compact Excavator. Attachments. Parts Manual Gehl Company All Rights Reserved.
|
|
- Lynne Bond
- 5 years ago
- Views:
Transcription
1 Compact Excavator Form 9880 Revision A October 2007 Attachments Parts Manual 2007 Gehl Company All Rights Reserved. Printed in USA
2 When ordering service parts, specify the correct part number, full description, quantity required and the unit model number and serial number. For your safety and continued proper operation, use only genuine GEHL service parts. The model and serial number for the unit are on a tag located on a panel on the front of the cab. ''Right'' and ''left'' are determined from a position sitting on the operator s seat and facing forward. GEHL Company reserves the right to make changes or improvements in the design or construction of any part of the unit without incurring the obligation to install such changes on any previously delivered units. Refer to the abbreviations table located on this page for special parts descriptions. Standard attaching hardware torque values are also provided near the back of this manual. Metric torque values shown in the illustrations are in Newton-meters and are converted to foot-pounds by multiplying by Specific reference numbers, indicating a complete assembly, are circled in some illustrations. A small bag, pictured in some illustrations, indicates a seal kit (seals, o-rings, etc.). In the exploded view parts list, additional information may follow the Reference Number. INTRODUCTION Unless otherwise specified, all cap screws and bolts are Grade 8.8, cadmium or zinc plated. NOTE:The following abbreviations may be used herein: ASSD... Assembled ASY... Assembly ASSY... Assembly AR... As Required CB... Carriage Bolt CP... Cotter Pin CS... Cap Screw (Hexagon Head) CYL... Cylinder DIA... Diameter FHCS... Flat Head Cap Screw GR... Grade HB... Hex Bolt HLN... Hex Lock Nut HN... Hex Nut HP... High Pressure HYD... Hydraulic INS... Insert LH... Left Hand LN... Lock Nut LT... Left LW... Lock Washer M... Meter or Meters MM/mm... Millimeter NPT... National Pipe Threaded NSS... Not Sold Separately RH... Right Hand RT... Right SHCS... Socket Head Cap Screw SLTD... Slotted SN... Serial Number or Slotted Nut SQ... Square W/... With 9880/AP007 Printed in U.S.A
3 TABLE OF CONTENTS Introduction... Table of Contents...2 Dipper Arm Identification...4 Bucket Geometry...5 Auxiliary Hydraulic Coupler Identification...6 General-Purpose Buckets...7 Models 42, Models Models 272, 292, 342, Models 753Z, 802, Heavy-Duty Buckets... Models 53, 92, 93, Werk Brau Heavy-Duty Buckets...2 Models 303, 353, 373, 383Z...2 Models 502, 503, 602, Models 753Z, 802, Models Ditching Buckets...6 All Models...6 Swivel Buckets...8 Models 42, Models 53, 92, 93, 222, 223, Models 272, 292, 342, Models 303, 353, 373, 383Z...2 Models 502, 503Z, 602, 603, Models 753Z, 802, Swivel Bucket Cylinders...24 Models 42, 52, 53, 92, 93, 222, 223, Models 272, 292, 303, 342, 353, 373, 383Z...25 Models 502, 503Z, 602, 603, Numerical Index...28 Printed in U.S.A /AP007
4 TABLE OF NOTES CONTENTS 9880/AP007 3 Printed in U.S.A
5 DIPPER ARM IDENTIFICATION Distance X Excavator Dipper Arm Identification Measurement Swivel buckets require different length hydraulic hoses depending upon the length of the dipper arm. Use the diagram and table on this page to determine dipper arm length. EARLIER DIPPER ARMS Excavator Model Number LATER DIPPER ARMS Short Dipper Arm Distance X Long Dipper Arm Distance X /4 (755 mm) 29-3/4 (755 mm) /2 (825 mm) 32-/2 (825 mm) /8 (576 mm) 32-/2 (826 mm) (70 mm) 39-3/4 (00 mm) (70 mm) 39-3/4 (00 mm) 383Z 35 (890 mm) 44-7/8 (40 mm) 503Z 39 (990 mm) 48-7/8 (240 mm) /4 (75 mm) 58 (475 mm) 753Z 46-7/8 (90 mm) 58-5/8 (490 mm) /4 (340 mm) 64-/2 (640 mm) /4 (35 mm) 55-3/4 (45 mm) Excavator Model Number Short Dipper Arm Distance X Long Dipper Arm Distance X /4 (755 mm) 29-3/4 (755 mm) /2 (825 mm) 32-/2 (825 mm) (70 mm) 39-3/4 (00 mm) (70 mm) 39-3/4 (00 mm) 383Z 35 (890 mm) 44-7/8 (890 mm) 503Z 39 (990 mm) 48-7/8 (990 mm) /4 (75 mm) 58 (75 mm) 753Z 46-7/8 (300 mm) 58-5/8 (300 mm) /4 (300 mm) 64-/2 (300 mm) /4 (35 mm) 55-3/4 (45 mm) Printed in U.S.A /AP007
6 BUCKET GEOMETRY Bucket Dipper Arm Bucket Bucket Geometry Measurements Excavator Model Number E - Pin Diameter F - Dipper Arm Width L - Bolt Distance Bucket Carrier 42.8 (30 mm) (08 mm) (08 mm) 52.8 (30 mm) (08 mm) (08 mm) (32 mm) (8 mm) (29.5 mm) (32 mm) (8 mm) (29.5 mm) (32 mm) (8 mm) (29.5 mm) (32 mm) (8 mm) (29.5 mm) (32 mm) (8 mm) (29.5 mm) (32 mm) (8 mm) (29.5 mm) (40 mm) 5.52 (40 mm) 6.22 (55.5 mm) (40 mm) 5.52 (40 mm) 6.22 (55.5 mm) (40 mm) 5.52 (40 mm) (80 mm) (40 mm) 5.52 (40 mm) 6.22 (55.5 mm) (40 mm) 5.52 (40 mm) (80 mm) (40 mm) 5.52 (40 mm) (80 mm) 383Z.575 (40 mm) 5.52 (40 mm) (80 mm) (40 mm) 5.52 (40 mm) (80 mm) 503Z.968 (50 mm) (95 mm) 9.29 (236 mm) (50 mm) (95 mm) 9.29 (236 mm) (50 mm) (95 mm) 9.29 (236 mm) (50 mm) (95 mm) 9.29 (236 mm) (50 mm) (95 mm) 9.29 (236 mm) 753Z 2.65 (55 mm) (70 mm).8 (300 mm) (55 mm) (70 mm).8 (300 mm) (55 mm) (70 mm).8 (300 mm) (60 mm) 8.66 (220 mm) 3.89 (335 mm) 9880/AP007 5 Printed in U.S.A
7 AUXILIARY HYDRAULIC COUPLER IDENTIFICATION Newer (Flat-Face) Hydraulic Couplers The auxiliary hydraulic circuit on recent excavators is equipped with flat-face style quick-couplers of this type. New attachments which use the auxiliary hydraulic circuit (such as swivel buckets) are equipped with quick-coupler fittings which fit this style. Older (Euro-Style) Hydraulic Couplers The auxiliary hydraulic circuit on older excavators is equipped with euro-style quick-couplers of this type. New attachments attachments which use the auxiliary hydraulic circuit (such as swivel buckets) are equipped with flat-faced style quick couplers which do not fit the older euro-style couplers. When buying new attachments, the euro-style quickcouplers must be replaced with the flat-face style couplers shown above. Printed in U.S.A /AP007
8 MODELS 42, 52 General-Purpose Buckets WERK BRAU /2/3 4/ NEUSON 0//2 3/ Part Description Capacity. Part Description Capacity * GENERAL-PURPOSE BUCKET (WERK BRAU) 8 (200 MM) * GENERAL-PURPOSE BUCKET (WERK BRAU) 0 (250 MM) * GENERAL-PURPOSE BUCKET (WERK BRAU) 2 (300 MM) * GENERAL-PURPOSE BUCKET (WERK BRAU) 6 (400 MM) * GENERAL-PURPOSE BUCKET (WERK BRAU) 20 (500 MM) * GENERAL-PURPOSE BUCKET (WERK BRAU) 24 (600 MM) BUCKET TOOTH (WERK BRAU) PIN (WERK BRAU) SHANK (WERK BRAU) 0.6 FT 3 (0.06 M 3 ) 0.8 FT 3 (0.022 M 3 ).0 FT 3 (0.028 M 3 ).2 FT 3 (0.033 M 3 ).5 FT 3 (0.042 M 3 ).8 FT 3 (0.005 M 3 ) N GENERAL-PURPOSE 8 (200 MM) N GENERAL-PURPOSE 0 (250 MM) N GENERAL-PURPOSE 2 (300 MM) N GENERAL-PURPOSE 6 (400 MM) N GENERAL-PURPOSE 20 (500 MM) N GENERAL-PURPOSE 24 (600 MM) BUCKET TOOTH (NEUSON) BOLT ((NEUSON) NUT (NEUSON) 0.6 FT 3 (0.06 M 3 ) 0.8 FT 3 (0.022 M 3 ).0 FT 3 (0.028 M 3 ).2 FT 3 (0.033 M 3 ).5 FT 3 (0.042 M 3 ).8 FT 3 (0.005 M 3 ) *Not an orderable part number 9880/AP007 7 Printed in U.S.A
9 MODEL 253 General-Purpose Buckets /2 3/4 5/ Part Description Capacity GENERAL-PURPOSE 0 (250 MM) GENERAL-PURPOSE 2 (300 MM) GENERAL-PURPOSE 6 (400 MM) GENERAL-PURPOSE 20 (500 MM) * GENERAL-PURPOSE 24 (600 MM) * GENERAL-PURPOSE 28 (700 MM).3 FT 3 (0.037 M 3 ) 2.4 FT 3 (0.067 M 3 ) 3.3 FT 3 (0.093 M 3 ) 4.7 FT 3 (033 M 3 ) 6.4 FT 3 (0.8 M 3 ) 3.8 FT 3 (0.07 M 3 ) BUCKET TOOTH BOLT NUT *Not an orderable part number Printed in U.S.A /AP007
10 MODELS 272, 292, 342, 362 General-Purpose Buckets WERK BRAU /2 3/4 5/ NEUSON 0/ 2/3 4/ Part Description Capacity. Part Description Capacity. * ** GENERAL-PURPOSE BUCKET (WERK BRAU) 8 (200 MM) 2* GENERAL-PURPOSE BUCKET (WERK BRAU) 2 (300 MM) 3* 80764** GENERAL-PURPOSE BUCKET (WERK BRAU) MM) 4* 80765** GENERAL-PURPOSE BUCKET (WERK BRAU) 20 (500 MM) 5* 80766** GENERAL-PURPOSE BUCKET (WERK BRAU) 24 (600 MM) 6* 80767** GENERAL-PURPOSE BUCKET (WERK BRAU) 28 (700 MM) BUCKET TOOTH (WERK BRAU) PIN (WERK BRAU) SHANK (WERK BRAU).4 FT 3 (0.040 M 3 ) 2.4 FT 3 (0.067 M 3 ) 3.3 FT 3 (0.093 M 3 ) 4.7 FT 3 (0.33 M 3 ) 6.4 FT 3 (0.8 M 3 ) 8.8 FT 3 (0.250 M 3 ) * N** GENERAL-PURPOSE 8 (200 MM) * 80763N GENERAL-PURPOSE 2 (300 MM) 2* 80764N GENERAL-PURPOSE MM) 3* 80765N GENERAL-PURPOSE 20 (500 MM) 4* 80766N GENERAL-PURPOSE 24 (600 MM) 5* 80767N GENERAL-PURPOSE 28 (700 MM) BUCKET TOOTH (NEUSON) BOLT (NEUSON) NUT (NEUSON).4 FT 3 (0.040 M 3 ) 2.4 FT 3 (0.067 M 3 ) 3.3 FT 3 (0.093 M 3 ) 4.7 FT 3 (0.33 M 3 ) 6.4 FT 3 (0.8 M 3 ) 8.8 FT 3 (0.250 M 3 ) *Requires 2 Connecting links 6573 **Not an orderable part number 9880/AP007 9 Printed in U.S.A
11 MODELS 753Z, 802, 803 General-Purpose Buckets WERK BRAU 2 3/4/ NEUSON 9 0 /2/ Part Description Capacity. Part Description Capacity GENERAL-PURPOSE BUCKET (WERK BRAU) 2 (300 MM) ** GENERAL-PURPOSE BUCKET (WERK BRAU) 8 (450 MM) GENERAL-PURPOSE BUCKET (WERK BRAU) 24 (600 MM) GENERAL-PURPOSE BUCKET (WERK BRAU) 30 (750 MM) ** GENERAL-PURPOSE BUCKET (WERK BRAU) 36 (900 MM) BUCKET TOOTH (WERK BRAU) PIN (WERK BRAU) SHANK (WERK BRAU) 3.3 FT 3 (0.093 M 3 ) 5. FT 3 (0.44 M 3 ) 7. FT 3 (0.20 M 3 ) 9.2 FT 3 (0.260 M 3 ).3 FT 3 (0.39 M 3 ) N GENERAL-PURPOSE 2 (300 MM) N GENERAL-PURPOSE 8 (450 MM) N GENERAL-PURPOSE 24 (600 MM) N GENERAL-PURPOSE 30 (750 MM) N** GENERAL-PURPOSE 36 (900 MM) BUCKET TOOTH (NEUSON) BOLT (NEUSON) NUT (NEUSON) 3.3 FT 3 (0.093 M 3 ) 5. FT 3 (0.44 M 3 ) 7. FT 3 (0.20 M 3 ) 9.2 FT 3 (0.260 M 3 ).3 FT 3 (0.39 M 3 ) *Use Neuson eqivalent for service **Not an orderable part number Printed in U.S.A /AP007
12 MODELS 53, 92, 93, 222, 223 Heavy-Duty Buckets WERK BRAU /2 3/ NEUSON /2 3/ Part Description Capacity. Part Description Capacity HEAVY-DUTY BUCKET (WERK BRAU) 0 (250 MM) HEAVY-DUTY BUCKET (WERK BRAU) 2 (300 MM) HEAVY-DUTY BUCKET (WERK BRAU) 6 (400 MM) HEAVY-DUTY BUCKET (WERK BRAU) 20 (500 MM) HEAVY-DUTY BUCKET (WERK BRAU) 24 (600 MM) BUCKET TOOTH (WERK BRAU) ROLL PIN (WERK BRAU) SHANK (WERK BRAU). FT 3 (0.03 M 3 ).3 FT 3 (0.037 M 3 ).6 FT 3 (0.045 M 3 ) 2.3 FT 3 (0.065 M 3 ) 2.7 FT 3 (0.076 M 3 ) N HEAVY-DUTY BUCKET (NEUSON) 0 (250 MM) N HEAVY-DUTY BUCKET (NEUSON) 2 (300 MM) N HEAVY-DUTY BUCKET (NEUSON) 6 (400 MM) N HEAVY-DUTY BUCKET (NEUSON) 20 (500 MM) N* HEAVY-DUTY BUCKET (NEUSON) 24 (600 MM) BUCKET TOOTH (NEUSON) BOLT (NEUSON) 8 * NUT (NEUSON) *Not an orderable part number. FT 3 (0.03 M 3 ).3 FT 3 (0.037 M 3 ).6 FT 3 (0.045 M 3 ) 2.3 FT 3 (0.065 M 3 ) 2.7 FT 3 (0.076 M 3 ) 9880/AP007 Printed in U.S.A
13 MODELS 303, 353, 373, 383Z Werk Brau Heavy-Duty Buckets 2/3 4/ Part Description Capacity. Part Description Capacity HEAVY-DUTY BUCKET 2 (300 MM) HEAVY-DUTY BUCKET 6 (400 MM) HEAVY-DUTY BUCKET 20 (500 MM) HEAVY-DUTY BUCKET 24 (600 MM).8 FT 3 (0.050 M 3 ) 2.4 FT 3 (0.067 M 3 ) 3. FT 3 (0.087 M 3 ) 3.8 FT 3 (0.07 M 3 ) HEAVY-DUTY BUCKET 28 (700 MM) 4.8 FT 3 (0.36 M 3 ) BUCKET TOOTH PIN SHANK Printed in U.S.A /AP007
14 MODELS 502, 503Z, 602, 652 Werk Brau Heavy-Duty Buckets 2/3 4/5/ Part Description Capacity. Part Description Capacity HEAVY-DUTY BUCKET 0 (250 MM) HEAVY-DUTY BUCKET 6 (400 MM) HEAVY-DUTY BUCKET 20 (500 MM) HEAVY-DUTY BUCKET 24 (600 MM) 2.5 FT 3 (0.070 M 3 ) 3.3 FT 3 (0.093 M 3 ) 3.7 FT 3 (0.04 M 3 ) 6.4 FT 3 (0.8 M 3 ) HEAVY-DUTY BUCKET 30 (750 MM) HEAVY-DUTY BUCKET 36 (900 MM) 8.8 FT 3 (0.249 M 3 ) 9.8 FT 3 (0.278 M 3 ) BUCKET TOOTH PIN SHANK 9880/AP007 3 Printed in U.S.A
15 MODELS 753Z, 802, 803 Werk Brau Heavy-Duty Buckets 2/3 4/5/6/ Part Description Capacity. Part Description Capacity HEAVY-DUTY BUCKET 2 (300 MM) HEAVY-DUTY BUCKET 6 (400 MM) HEAVY-DUTY BUCKET 8 (450 MM) HEAVY-DUTY BUCKET 20 (500 MM) HEAVY-DUTY BUCKET 24 (600 MM) 3.9 FT 3 (0.0 M 3 ) 5.5 FT 3 (0.56 M 3 ) 6.2 FT 3 (0.76 M 3 ) 7.0 FT 3 (0.98 M 3 ) 8.0 FT 3 (0.227 M 3 ) HEAVY-DUTY BUCKET 30 (750 MM) HEAVY-DUTY BUCKET 36 (900 MM) 0.9 FT 3 (0.308 M 3 ) 3.4 FT 3 (0.379 M 3 ) BUCKET TOOTH PIN SHANK Printed in U.S.A /AP007
16 MODEL 202 Werk Brau Heavy-Duty Buckets /2/3/4/ Part Description Capacity. Part Description Capacity HEAVY-DUTY BUCKET 30 (750 MM) 2* * HEAVY-DUTY BUCKET 36 (900 MM) 3* HEAVY-DUTY BUCKET 40 (000 MM) 4* HEAVY-DUTY BUCKET 42 (050 MM) 4 FT 3 (0.396 M 3 ) 7 FT 3 (0.48 M 3 ) 8 FT 3 (0.509 M 3 ) 20 FT 3 (0.560 M 3 ) HEAVY-DUTY BUCKET 30 (750 MM) 4 FT M 3 ) BUCKET TOOTH PIN SHANK *Additional counterweight required. See excavator parts manual. 9880/AP007 5 Printed in U.S.A
17 ALL MODELS Ditching Buckets Bucket Part Description Capacity GENERAL-PURPOSE DITCHING BUCKET 3 (775 MM) FT 3 (0.040 M 3 ) Bucket Part Description Capacity 8076 GENERAL-PURPOSE DITCHING BUCKET 33 (800 MM) FT 3 (0.040 M 3 ) * * * Bucket Part Description Capacity * Z GENERAL-PURPOSE DITCHING BUCKET 39 (000 MM) *Not an orderable part number; Models 253, 303, & 373 need two connecting links 6573.See excavator parts manual 3.6 FT 3 (0.0 M 3 ) Bucket Part Description Capacity Bucket Part Description Capacity GENERAL-PURPOSE DITCHING BUCKET 33 (700 MM).9 FT 3 (0.062 M 3 ) HEAVY-DUTY DITCHING BUCKET 39 (000 MM) HEAVY-DUTY DITCHING BUCKET 55 (400 MM) 4. FT 3 (0.6 M 3 ) 5.9 FT 3 (0.67 M 3 ) Printed in U.S.A /AP007
18 ALL MODELS Ditching Buckets 503Z Bucket Part Description Capacity HEAVY-DUTY DITCHING BUCKET 48 (000 MM) 80948* HEAVY-DUTY DITCHING BUCKET 48 (000 MM) 80949* HEAVY-DUTY DITCHING BUCKET 55 (400 MM) 5.9 FT 3 (0.67 M 3 ) 7.0 FT 3 (0.98 M 3 ) 8.4 FT 3 (0.238 M 3 ) 202 *Not an orderable part number Bucket Part Description Capacity * HEAVY-DUTY DITCHING BUCKET 60 (525 MM) 22.7 FT 3 (0.643 M 3 ) *Contact CEA Attachments W Bucket Part Description Capacity HEAVY-DUTY DITCHING BUCKET 48 (000 MM) 5.9 FT 3 (0.67 M 3 ) 753Z Bucket Part Description Capacity HEAVY-DUTY DITCHING BUCKET 48 (000 MM) HEAVY-DUTY DITCHING BUCKET 60 (525 MM) 7.6 FT 3 (0.25 M 3 ) 9.7 FT 3 (0.275 M 3 ) 9880/AP007 7 Printed in U.S.A
19 MODELS 42, 52 Swivel Buckets Part Description Qty BUCKET/SWIVEL 3 (850 MM).6 FT 3 (0.045 M 3 ) GREASE ZERK HN SLTD M36-4 C8ZY CYLINDER See page 24 for individual components PIN COTTER PIN LW M8 R PIN HEX SCREW SWIVEL BRACKET PIN BUSHING 45/55 X SCREW JOINT PIN/SPRING M6.3 X 63 ZO Part Description Qty CAP ELBOW HP HOSE HP HOSE QUICK COUPLER (Flat-face coupler. See page 6) DUST PLUG QUICK COUPLER (Flat-Face coupler. See page 6) DUST CAP QUICK COUPLER (Euro-style coupler. See page 6) DUST PLUG QUICK COUPLER (Euro-style coupler. See page 6) DUST CAP Printed in U.S.A /AP007
20 MODELS 53, 92, 93, 222, 223, 253 Swivel Buckets Part Description Qty BUCKET/SWIVEL 33 (850 MM) 2.0 FT 3 (0.057 M 3 ) GREASE ZERK HN SLTD M36-4 C8ZY CYLINDER See page 24 for individual components PIN COTTER PIN LW M8 R PIN HEX SCREW SWIVEL BRACKET PIN BUSHING 45/55 X SCREW JOINT PIN/SPRING M6.3 X 63 ZO CAP ELBOW 2 Part Description Qty HP HOSE HP HOSE (REQUIRED FOR LONG DIPPER ARM ON MODELS 252/ME2503) HP HOSE HP HOSE (REQUIRED FOR LONG DIPPER ARM ON MODELS 252/ME250) QUICK COUPLER (Flat-face coupler. See page 6) DUST PLUG QUICK COUPLER (Flat-Face coupler. See page 6) DUST CAP QUICK COUPLER (Euro-style coupler. See page 6) DUST PLUG QUICK COUPLER (Euro-style coupler. See page 6) DUST CAP 9880/AP007 9 Printed in U.S.A
21 MODELS 272, 292, 342, 362 Swivel Buckets Part Description Qty BUCKET/SWIVEL 39 (000 MM) 3.0 FT 3 (0.0 M 3 ) 3 64 GREASE ZERK HN SLTD M36-4 C8ZY SWIVEL BUCKET CYLINDER See page 25 for individual components PIN COTTER PIN LN INS M8-.25 C8ZY PIN HB M8-.25 X SWIVEL BRACKET ( ) PIN BUSHING FLAT WASHER PIN/SPRING M6.3 X 63 ZO CAP Part Description Qty SCREW JOINT HP HOSE HP HOSE SCREW JOINT QUICK COUPLER (Flat-face coupler. See page 6) DUST PLUG QUICK COUPLER (Flat-Face coupler. See page 6) DUST CAP QUICK COUPLER (Euro-style coupler. See page 6) DUST PLUG QUICK COUPLER (Euro-style coupler. See page 6) DUST CAP Printed in U.S.A /AP007
22 MODELS 303, 353, 373, 383Z Swivel Buckets , Part Description Qty BUCKET/SWIVEL 40 (000 MM) 3.9 FT 3 (0.0 M 3 ) BUCKET/SWIVEL 55 (400 MM) 5.6 FT 3 (0.59 M 3 ) GREASE ZERK HN SLTD M36-4 C8ZY SWIVEL BUCKET CYLINDER See page 25 for individual components PIN COTTER PIN LN INS M8-.25 C8ZY PIN HB M8-.25 X SWIVEL BUCKET PIN BUSHING FLAT WASHER PIN/SPRING M6.3 X 63 ZO CAP SCREW JOINT 2 Part Description Qty HP HOSE (REQUIRED FOR SHORT DIPPER ARM) HP HOSE (REQUIRED FOR LONG DIPPER ARM) HP HOSE (REQUIRED FOR SHORT DIPPER ARM) HP HOSE (REQUIRED FOR LONG DIPPER ARM) SCREW JOINT QUICK COUPLER (Flat-face coupler. See page 6) DUST PLUG QUICK COUPLER (Flat-Face coupler. See page 6) DUST CAP QUICK COUPLER (Euro-style coupler. See page 6) DUST PLUG QUICK COUPLER (Euro-style coupler. See page 6) DUST CAP 9880/AP007 2 Printed in U.S.A
23 MODELS 502, 503Z, 602, 603, 652 Swivel Buckets , , , Part Description Qty BUCKET/SWIVEL 48 (200 MM) 5.9 FT 3 (0.67 M 3 ) BUCKET/SWIVEL 48 (200 MM) 7.0 FT 3 (0.98 M 3 ) BUCKET/SWIVEL 55 (400 MM) 8.4 FT 3 (0.238 M 3 ) 3 64 GREASE ZERK HN SLTD M48-3 F8 ZY CYLINDER/SWIVEL BUCKET See page 26 for individual components PIN HB M8-.25 X 60 C8.8SY LN INS M8-.25 C8 ZY PIN HB M8-.25 X 70 C8.8 ZY SWIVEL BRACKET PIN BUSHING 2 Part Description Qty SPACER/SWIVEL BRACKET PIN/SPRING M8 X 80 ZO PROTECTION CAP SCREW JOINT 2L HP HOSE (REQUIRED FOR SHORT DIPPER ARM) HP HOSE (REQUIRED FOR LONG DIPPER ARM) HP HOSE (REQUIRED FOR SHORT DIPPER ARM) HP HOSE (REQUIRED FOR LONG DIPPER ARM) ( ) SCREW JOINT COUPLING/FEMALE DUST CAP SLEEVE COUPLING/MALE A3 BG DUST CAP PLUG Printed in U.S.A /AP007
24 MODELS 753Z, 802, 803 Swivel Buckets , Part Description Qty BUCKET/SWIVEL 60 (525 MM) 8.8 FT 3 (0.250 M 3 ) G SCREW SPRING RING WASHER B7-40HV A2C GREASE ZERK PIN/SPRING M8 X 80 ZO GROOVED BUSHING PIN CS M2-.75 X 30 C0.9 ZO LW SPRING B2 DIM WASHER GR A PIN PIN PIN CYLINDER/SWIVEL BUCKET Part Description Qty SCREW JOINT SPACER CROWN NUT PIN SEAL KIT HP HOSE (REQUIRED FOR SHORT 2 DIPPER ARM) HP HOSE (REQUIRED FOR LONG 2 DIPPER ARM) SCREW JOINT COUPLING/MALE A7 3/ DUST CAP SLEEVE COUPLING/FEMALE A7 3/ DUST CAP PLUG HP HOSE HP HOSE 9880/AP Printed in U.S.A
25 MODELS 42, 52, 53, 92, 93, 222, 223, 253 Swivel Bucket Cylinders Part Description Qty CYLINDER SEAL KIT ELBOW GREASE ZERK PISTON ROD BUSHING GUIDE BUSHING PISTON SET SCREW DUST CAP Printed in U.S.A /AP007
26 MODELS 272, 292, 303, 342, 353, 373, 383Z Swivel Bucket Cylinders Part Description Qty SWIVEL BUCKET CYLINDER SEAL KIT TILT BUCKET SCREW 2L GREASE ZERK PISTON ROD STEEL BUSHING GUIDE BUSHING PISTON THREAD PIN SET SCREW PROTECTION CAP /AP Printed in U.S.A
27 MODELS 502, 503Z, 602, 603, 652 Swivel Bucket Cylinders Part Description Qty SWIVEL BUCKET CYLINDER SEAL KIT TILT BUCKET CYLINDER SCREW JOINT 2L GREASE ZERK PISTON ROD STEEL ROD GUIDE BUSHING PISTON SET SCREW PROTECTION CAP Printed in U.S.A /AP007
28 MODELS 502, 503Z, 602, 603, 652 Swivel Bucket Cylinders NOTES 9880/AP Printed in U.S.A
29 Numerical Index Part Page Part Page Part Page Printed in U.S.A /AP007
30 Numerical Index Part Page Part Page Part Page /AP Printed in U.S.A
31 Numerical Index Part Page Part Page N N N N N N N N N N N N N N N N N N N N N G 23 2 Printed in U.S.A /AP007
32 Numerical Index NOTES 9880/AP007 3 Printed in U.S.A
33 TORQUE SPECIFICATIONS Note: Use these torque values when tightening Gehl hardware (excluding: locknuts and self-tapping, thread forming and sheet metal screws) unless specified otherwise. Hydraulic fittings with various seals (light application). All torque values are in lb.-ft. (Nm) unless marked otherwise. Thread Straight pipe fitting with thread and screwed plug (GE) Non-return valve Identification aid Sealing washer Elastic seal O-ring with elastic seal outside Ø M0X.0 7 (9) 3 (8) (5) 3 (8) 0.4 in. (0 mm) M2X.5 5 (20) 8 (25) 8 (25) 8 (25) 0.5 in. (2 mm) M4X.5 26 (35) 33 (45) 26 (35) 26 (35) 0.6 in. (4 mm) M6X.5 33 (45) 4 (55) 30 (40) 37 (50) 0.6 in. (6 mm) M8X.5 4 (55) 52 (70) 33 (45) 52 (70) 0.7 in. (8 mm) M22X.5 48 (65) 92 (25) 44 (60) 92 (25) 0.9 in. (22 mm) M27X (90) 33 (80) 74 (00) 07 (45).0 in. (27 mm) M33X2.0 (50) 229 (30) 8 (60) 55 (20).3 in. (33 mm) M42X (240) 332 (450) 55 (20) 266 (360).7 in. (42 mm) M48X (290) 398 (540) 92 (260) 398 (540).9 in. (48 mm) G/8A 7 (9) 3 (8) (5) 3 (8) 0.4 in. (9.73 mm) G/4A 26 (35) 26 (35) 22 (30) 26 (35) 0.5 in. (3.6 mm) G3/8A 33 (45) 52 (70) 33 (45) 37 (50) 0.7 in. (6.66 mm) G/2A 48 (65) 66 (90) 4 (55) 48 (65) 0.8 in. (20.96 mm) G3/4A 66 (90) 33 (80) 74 (00) 03 (40).0 in. (26.44 mm) GA (50) 229 (30) 8 (60) 40 (90).3 in. (33.25 mm) G /4A 77 (240) 332 (450) 55 (20) 266 (360).7 in. (4.9 mm) G /2A 24 (290) 398 (540) 92 (260) 398 (540).9 in. (47.80 mm) Printed in U.S.A 9880/AP007
34 Hydraulic fittings with various seals (heavy application). All torque values are in lb.-ft. (Nm) unless marked otherwise. Thread Straight pipe fitting with thread and screwed plug (GE) Non-return valve Identification aid Sealing washer Elastic seal O-ring with elastic seal outside Ø M2X.5 5 (20) 26 (35) 26 (35) 26 (35) 0.5 in. (2 mm) M4X.5 26 (35) 4 (55) 33 (45) 33 (45) 0.6 in. (4 mm) M6X.5 33 (45) 52 (70) 4 (55) 4 (55) 0.6 in. (6 mm) M8X.5 4 (55) 66 (90) 52 (70) 52 (70) 0.7 in. (8 mm) M20X.5 4 (55) 92 (25) 59 (80) 74 (00) 0.8 in. (20 mm) M22X.5 48 (65) 00 (35) 74 (00) 92 (25) 0.9 in. (22 mm) M27X (90) 33 (80) 25 (70) 00 (35).0 in. (27 mm) M33X2.0 (50) 229 (30) 229 (30) 55 (20).3 in. (33 mm) M42X (240) 332 (450) 243 (330) 266 (360).7 in. (42 mm) M48X (290) 398 (540) 30 (420) 398 (540).9 in. (48 mm) G/8A 26 (35) 4 (55) 33 (45) 33 (45) 0.5 in. (3.6 mm) G/4A 33 (45) 59 (80) 44 (60) 44 (60) 0.7 in. (6.66 mm) G3/8A 48 (65) 85 (5) 55 (75) 74 (00) 0.8 in. (20.96 mm) G/2A 66 (90) 33 (80) 25 (70) 07 (45).0 in. (26.44 mm) G3/4A (50) 229 (30) 229 (30) 92 (260).3 in. (33.25 mm) GA 77 (240) 332 (450) 243 (330) 266 (360).7 in. (4.9 mm) G /4A 24 (290) 398 (540) 30 (420) 398 (540).9 in. (47.80 mm) 9880/AP007 Printed in U.S.A
35 With coarse-pitch thread. All torque values are in lb.-ft. (Nm) unless marked otherwise. Thread Threads according to DIN 92, DIN 93, DIN 933, etc. Threads according to DIN M5 4. (5.5) 6 (8) 7 (0) 4 (5) 5 (7) M6 7 (0) 0 (4) 3 (7) 6.3 (8.5) 9 (2) M8 8 (25) 26 (35) 3 (42) 5 (20) 22 (30) M0 33 (45) 48 (65) 59 (80) 30 (40) 44 (59) M2 64 (87) 8 (0) 08 (47) 5 (69) 74 (00) M4 00 (35) 33 (80) 70 (230) 8 (0) 8 (60) M6 55 (20) 203 (275) 258 (350) 25 (70) 84 (250) M8 207 (280) 302 (40) 354 (480) 8 (245) 254 (345) M (40) 420 (570) 509 (690) 25 (340) 36 (490) M (550) 575 (780) 686 (930) 339 (460) 487 (660) M (70) 738 (000) 878 (90) 435 (590) 620 (840) M (040) 092 (480) 305 (770) 642 (870) 922 (250) M (420) 482 (200) 770 (2400) 885 (200) 254 (700) With fine-pitch thread. All torque values are in lb.-ft. (Nm) unless marked otherwise. Thread Threads according to DIN 92, DIN 93, DIN 933, etc. Threads according to DIN M8X.0 8 (25) 27 (37) 32 (43) 6 (22) 24 (32) M0X.0 37 (50) 55 (75) 65 (88) 32 (43) 48 (65) M0X (49) 52 (7) 6 (83) 3 (42) 46 (62) M2X (87) 96 (30) (50) 55 (75) 8 (0) M2X.5 6 (83) 92 (25) 07 (45) 53 (72) 77 (05) M4X.5 00 (35) 48 (200) 73 (235) 89 (20) 29 (75) M6X.5 55 (20) 229 (30) 266 (360) 33 (80) 95 (265) M8X (35) 332 (450) 39 (530) 99 (270) 284 (385) M20X (440) 465 (630) 538 (730) 277 (375) 39 (530) M22X (590) 620 (840) 723 (980) 369 (500) 524 (70) M24X (740) 789 (070) 922 (250) 465 (630) 664 (900) M27X2.0 8 (00) 43 (550) 328 (800) 679 (920) 959 (300) M30X (500) 586 (250) 844 (2500) 959 (300) 364 (850) Printed in U.S.A 9880/AP007
36 Gehl Company 43 Water Street, P.O. Box 79, West Bend, WI U.S.A /AP GEHL Company. All rights reserved. Printed in U.S.A
480T All-Wheel-Steer. Loader
480T All-Wheel-Steer Form No. 918119 Revision C Loader Beginning Serial Number: 342100107 PARTS MANUAL Introduction When ordering service parts, specify the correct part number, full description, quantity
More informationGE1202. Compact Excavator
GE1202 Form No. 908171 Compact Excavator PARTS MANUAL Introduction When ordering service parts, specify the correct part number, full description, quantity required, the unit model number and serial number.
More information153 Compact Excavator
153 Compact Excavator Form No. 918035 Revision D Beginning Serial Number: AB00440 PARTS MANUAL Introduction When ordering service parts, specify the correct part number, full description, quantity required,
More information193 & 223. Compact Excavators
193 & 223 Form No. 909827 Compact Excavators PARTS MANUAL Introduction When ordering service parts, specify the correct part number, full description, quantity required, the unit model number and serial
More informationTD 3.6 L4. Parts Manual. Deutz Engine. Telescopic Handlers. Gehl RS6-34 (Tier IV) Manitou MT6034 T (Tier IV)
TD 3.6 L4 Form No. 50960088 Revision A September 04 Deutz Engine Telescopic Handlers Gehl RS6-34 (Tier IV) Manitou MT6034 T (Tier IV) Parts Manual Introduction Deutz TD 3.6 L4 The Table of Contents pages
More informationForm No Replaces /420. Finger Wheel V-Rakes PARTS MANUAL
8/20 Form No. 90988 Replaces 9082 Finger Wheel V-Rakes PARTS MANUAL Introduction When ordering service parts, specify the correct part number, full description, quantity required, the unit model number
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL HD, R & THD SERIES SNOW PLOWS WITH EIS PLOW LIGHT HARNESS CONNECTIONS FOR GRAVITY HYDRAULICS WITH SERIAL NUMBER AFTER: HDG00000 FOR DOWN PRESSURE HYDRAULICS WITH SERIAL NUMBERS AFTER:
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL HD, R & THD SERIES SNOW PLOWS WITH EIS PLOW LIGHT HARNESS CONNECTIONS FOR GRAVITY HYDRAULICS WITH SERIAL NUMBER AFTER: HDG00000 FOR DOWN PRESSURE HYDRAULICS WITH SERIAL NUMBERS AFTER:
More informationCompact Excavator. Beginning Serial Number: AC Form No Revision C 07/06 PARTS MANUAL
603 Compact Excavator Beginning Serial Number: AC02472 Form 918072 Revision C 07/06 PARTS MANUAL INTRODUCTION When ordering service parts, specify the correct part number, full description, quantity required,
More informationParts Manual 503Z. Compact Excavator. Beginning Serial Number: AC Form No Revision F Mar. 2008
503Z Form 918071 Revision F Mar. 2008 Compact Excavator Beginning Serial Number: AC02471 Parts Manual 2008 Gehl Company All Rights Reserved. Printed in USA INTRODUCTION When ordering service parts, specify
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL VHD SERIES SNOW PLOW WITH SERIAL NUMBERS AFTER VHD00000 and VHD100000 Sno-Way, Down Pressure and EIS are registered trademarks of Sno-Way International, Inc. ProControl, V-Wing, Revolution
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL MEGABLADE TM REVOLUTION TM SERIES SNOW PLOW WITH SERIAL NUMBER AFTER MBR0000 Sno-Way, Down Pressure and EIS are registered trademarks of Sno-Way International, Inc. ProControl, MegaBlade,
More informationModel 802 Center Mount Adapter For New Holland 9030 & TV140 Bi-Directional Tractors PARTS CATALOG
Model 802 Center Mount Adapter For New Holland 9030 & TV140 Bi-Directional Tractors 1 PARTS CATALOG TABLE OF CONTENTS Frame & Tractor Linkage...2,3 Header Linkage & Float Group...4,5 Header Drive Hydraulics
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL SERIES AND R SNOW PLOWS WITH EIS PLOW LIGHT HARNESS CONNECTIONS FOR GRAVITY HYDRAULICS WITH SERIAL NUMBERS BEFORE G000 WITH SERIAL NUMBERS AFTER G00000 FOR DOWN PRESSURE HYDRAULICS
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL 28V SERIES SNOW PLOWS FOR PLOW SERIAL NUMBERS AFTER 28VG100000 28VD100000 07 Sno-Way International 9710097F TABLE OF CONTENTS Page PARTS LIST INTRODUCTION... 2 POWER PACK FRAME...
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL MEGABLADE TM V-WING TM SERIES SNOW PLOW WITH SERIAL NUMBERS AFTER MBV00000 Sno-Way, Down Pressure and EIS are registered trademarks of Sno-Way International, Inc. ProControl, MegaBlade,
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL HTV SERIES SNOW PLOW FOR SERIAL NUMBERS AFTER HTV0000 Sno-Way, Down Pressure and EIS are registered trademarks of Sno-Way International, Inc. ProControl, MegaBlade, V-Wing, E-Z Switch,
More informationParts Manual. HL360 Loader
HL360 Loader Parts Manual Parts Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF GEHL OR IT S SUCCESSORS. GEHL AND IT S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY OR ACCURACY
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL, HD, R, T, THD & SERIES SNOW PLOWS WITH EIS PLOW LIGHT HARNESS CONNECTIONS FOR GRAVITY & CENTRAL HYDRAULICS WITH SERIAL NUMBERS BEFORE: G000, TG00, G000, C00 WITH SERIAL NUMBER AFTER:
More informationParts Manual. Model 502. Compact Excavator. Serial Number AA01022 to AA Form No Revision B July 2007
Model 502 Form 908542 Revision B July 2007 Compact Excavator Serial Number AA01022 to AA01890 Parts Manual 2007 Gehl Company All Rights Reserved. Printed in USA INTRODUCTION When ordering service parts,
More informationPARTS MANUAL SUPPORTED BY HUSTLER TURF EQUIPMENT AND EXCEL INDUSTRIES, INC.
SHIBAURA DIESEL ENGINE MODEL: N843 and N843L PARTS MANUAL SUPPORTED BY HUSTLER TURF EQUIPMENT AND EXCEL INDUSTRIES, INC. Table of Contents Chapter 1 General Information....................................
More informationHYDROBURST HB3038, HB5058, HB80, HB125
TM HYDROBURST HB3038, HB5058, HB80, HB125 Parts Manual HYDROBURST HB3038, HB5058, HB80 & HB125 s/n Part No. PM1251 INTRODUCTION HOW TO USE THE MANUAL This manual contains illustrations and parts list of
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL SNOW PLOW AND SPREADER CONTROLS 0 Sno-Way International 9710C TABLE OF CONTENTS Page PARTS LIST INTRODUCTION... PARTS - SNOW PLOW CONTROLS Legacy Control System Transmitter (Straight
More informationDana Spicer Steer Axles
Dana Spicer Steer Axles I Family D Family Illustrated Parts List AXIP-0090 November 2005 For the most current information, visit the Roadranger web site at www.roadranger.com Table of Contents Table of
More informationProdigy Parts Manual Part No
Prodigy Parts Manual Part No. 999-858.01 Table of Contents Parts List and Illustrations Page Number Kits and Routine Maintenance Parts Table...iv Hydraulic Component Location... 1 Engine and Hydraulic
More informationProdigy Parts Manual Part No
Prodigy Parts Manual Part No. 999-88.02 Table of Contents Parts List and Illustrations Page Number Kits and Routine Maintenance Parts Table...iv Hydraulic Component Location... 1 Engine and Hydraulic Pump
More informationOperation and Parts Manual
Operation and Parts Manual 3-Point PTO and Hydraulic Stump Grinders Models: SC-25 and SC-25H SC-50 and SC-50H Safety Operation Maintenance Repair Troubleshooting Parts Parts SC-50 and SC-50-H Stumpbuster
More informationParts Book 612N, 812N, 642N, 842N, 862N 714NT, 814NT, 742NT, 842NT, 862NT
Parts Book 612N, 812N, 642N, 842N, 862N 714NT, 814NT, 742NT, 842NT, 862NT Wishek Mfg. LLC 112 South 2nd Street PO Box 185 Wishek, ND 58495 (701) 452-2449 www.wishekmfg.com WARRANTY/ PARTS RETURN POLICY
More informationParts Manual. Compact Excavator. Beginning Serial Number: AB Form No Revision C Feb. 2009
602 Form 9804 Revision C Feb. 2009 Compact Excavator Beginning Serial Number: AB00473 Parts Manual 2009 Gehl Company All Rights Reserved Printed in USA INTRODUCTION When ordering service parts, specify
More informationReproduction. Not for. Parts Manual. 6016RT / 7016RT Rear Tine Tillers
Parts Manual Attachment Mfg. No. Description 1695583 6016 RT, 8TP Tiller 1695767 7016 RT, 9TP Tiller 1695923 7016 RT, 9TP Tiller 6016RT / 7016RT Rear Tine Tillers Not for Reproduction Manual Part No. Revision
More informationParts Manual. Model 502. Compact Excavator. Serial Number AB00473 to AB Form No Revision C July 2007
Model 502 Form 918040 Revision C July 2007 Compact Excavator Serial Number AB00473 to AB02974 Parts Manual 2007 Gehl Company All Rights Reserved. Printed in USA INTRODUCTION When ordering service parts,
More informationFor New Holland CR 920/940/960/970/980/9040/9060/9080 CX 720/740/760/780/820/840/860/880/8030/8040/8050/8060/8070/8080/8090
PARTS CATALOG MUD HOG REAR WHEEL DRIVE For New Holland CR 920/940/960/970/980/9040/9060/9080 CX 720/740/760/780/820/840/860/880/8030/8040/8050/8060/8070/8080/8090 TUTHILL DRIVE SYSTEMS MODEL NUMBERS: CNH4005
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL 9, 9T & SERIES SNOW PLOWS WITH EIS FOR PLOW SERIAL NUMBERS AFTER 9G100000, 9D100000, 9C100000 9TG100000, 9TD100000, 9TC100000 G10000, D100, C10000 00 Sno-Way International 910089H
More informationParts Manual AWS 46. All-Wheel-Steer Loader. Beginning Serial Number: Form No Revision B Jan. 2010
AWS 46 All-Wheel-Steer Loader Beginning Serial Number: 347040005 Form 918266 Revision B Jan. 2010 Parts Manual 2010 Gehl Company All Rights Reserved. Printed in USA INTRODUCTION When ordering service parts,
More informationReproduction. Not for. Walk Behind Mowers 19" & 21" Parts Manual. Attachments
Parts Manual Attachments Walk Behind Mowers 19" & 21" Mfg. No. Description 881633 ESPV19875EXAL, 19" Self Propelled Walk Mower (Export) 881634 ESPV21875EXAL, 21" Self Propelled Walk Mower (Export) Manual
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL SERIES SNOW PLOWS FOR PLOW SERIAL NUMBERS AFTER D0000 G0000 00 Sno-Way International 9F TABLE OF CONTENTS Page PARTS LIST INTRODUCTION... POWER PACK FRAME... BLADES... HYDRAULIC SYSTEM
More informationHustler Mini Z Bac Vac Parts Manual
Hustler Mini Z Bac Vac Parts Manual Hustler Turf Equipment P.O. Box 7000 Hesston, Kansas 67062-2097 379263 Rev. 6/06 Table of Contents Chapter General Information.................................... Chapter
More informationBackhoe Dingo. Compact Utility Loader. Parts Catalog. Form Number Rev A. Model No and up.
Form Number 3353-321 Rev A Backhoe Dingo Compact Utility Loader Model No. 23163-250000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the
More informationModel 1550 Series In-Row Ripper Parts Manual
Model 1550 Series In-Row Ripper Parts Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-299-0111 01/2011 Table of Contents 1 Instructions
More informationHR930 Rotary Rake. Illustrated Parts Breakdown. Tongue & Main Frame. Gearbox & Tine Arm
HR0 Rotary Rake Illustrated Parts Breakdown Page Page Page Page Page Page Tongue & Main Frame Guards Gearbox & Tine Arm Axle Assembly Rotary Gearbox PTO Shaft 0//0 Tongue & Main Frame 0 0 0 0 Ref# Description
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL SERIES SNOW PLOWS FOR PLOW SERIAL NUMBERS AFTER D00000 G00000 007 Sno-Way International 9700D TABLE OF CONTENTS Page PARTS LIST INTRODUCTION... POWER PACK FRAME... BLADES... HYDRAULIC
More informationTWIN ROTARY RAKE PARTS BOOK MODEL
TWIN ROTARY RAKE PARTS BOOK MODEL 2650 17.01135 This parts book is furnished for your convenience only. All parts must be purchased through an authorized dealer. Call us for a dealer near you. Issue Date:
More informationFRONT TINE TILLERS SERIES 0 & 1
Parts Manual for FRONT TINE TILLERS SERIES 0 & 1 MODEL 300T 301T 401TCR 500T 500TC 500TRC 501T 501TC McDonough, GA, 30253 U.S.A. COPYRIGHT 2006 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 6, 3/7/2006
More informationINDEX BACKHOE WOODS BH750WD PARTS CATALOG HOME TRACTORS ATTACHMENTS. Backhoe Nomenclature
R Ingersoll BACKHOE WOODS BH750WD PARTS CATALOG 8-3060 HOME TRACTORS ATTACHMENTS BUCKETS... 7 CONTROLS...9 CYLINDERS Swing and Bucket...13 CYLINDERS Boom, Dipperstick and Stabilizer...15 DECALS...17 DIPPERSTICK...7
More informationForm No Replaces /522. Finger Wheel Rakes PARTS MANUAL
520/522 Form No. 909874 Replaces 906157 Finger Wheel Rakes PARTS MANUAL Introduction When ordering service parts, specify the correct part number, full description, quantity required, the unit model number
More informationSupplement to Spare Parts Catalogue. Model : FT Dual Transmission - F
Supplement to Spare Parts Catalogue Model : FT - 60 Dual Transmission - F10001760 CONTENTS Tab. No. Sheet No. DESCRIPTION Page No. 1 101764-8 HEAD LIGHT, REAR LIGHT AND PLOUGH 1 LAMP 2 101766A-7 SHEET
More informationLycoming Aircraft Engines Parts Catalog
Aircraft Engines Parts Catalog IO-0-BG Wide Cylinder Flange Crankcase Model Engine Part No. PC-0- Oliver Street Williamsport, PA 770 Aircraft Engines Parts Catalog IO-0-BG Wide Cylinder Flange Crankcase
More informationBUSH HOG LAND MAINTENANCE REPAIR PARTS MANUAL MODEL: TD-1100 SECTION: 66
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODEL: TD-00 SECTION: 0 Griffin Ave. Selma, AL 0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com BUSH HOG/ LAND MAINTENANCE REPAIR S MANUAL JUNE, 00
More informationInstructions for Parts Books
Instructions for Parts Books The heading at the top of the page will be the same for the picture of the parts at it is for the page with the part numbers. Definition of column headings on part number pages:
More informationParts list. See Frame parts list Page 12. See hydraulic pump. exploded view. Page 14. See work head. exploded view. Page 7
Parts list See Frame parts list Page 12 See hydraulic pump exploded view Page 14 See work head exploded view Page 7 See electrical parts list Page 18 See hoist parts list Page 11 See Frame parts list Page
More informationTT4100 Rotary Tedder
TT0 Rotary Tedder Serial numbers 0 and higher Illustrated Parts Breakdown Page Page Tongue Assembly S/N - Tongue Assembly S/N to Page Page Page Page Page Tongue Assembly S/N to Tongue Assembly S/N + Main
More informationPARTS LIST BW 3500 TP
PARTS LIST BW 500 TP -57-000 # PART # Qty TITLE NC7--00 BUSHING 0.80'' ID X.0'' OD X 0.0'' 5-55-070 SERIAL NUMBER PLATE CREATION : 5-0-0 REVISION : 9-09-08 ASSEMBLY CASING ASSEMBLY : -57-000 AUTHOR : Page
More informationPavement Services, Inc.
MG68 Parts Manual Pavement Services, Inc. Page 30 29 30 29 25 25 24 30 4 26 29 4 25 26 4 Page 2 The Decal Kit for the Model MG68 Maintainer is Item Part # Description 056859 DECAL, ANTI-FREEZE (BLACK)
More informationPost Hole Digger SA30 & SA P Parts Manual. Copyright 2011 Printed 04/01/11
Table of Contents Post Hole Digger SA30 & SA35 19221 317-093P Parts Manual Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without
More informationTT4101 Rotary Tedder
TT Rotary Tedder 0//0 Illustrated Parts Breakdown Page Page Page Page Page Page Page Page Page Page Page Tongue Assembly S/N S/N - Tongue Assembly S/N + Main Frame S/N - Main Frame S/N to Main Frame S/N
More informationFold Hydraulics Item Qty Part No. Description
Fold Hydraulics 1 2 465385 Quick Coupler 3/4"-16 FOR 2 2 469882 Hose ½" x 468" (3/4 FJSw x 3/4 MOR) 3 2 469833 Hose ½" x 87" (3/4 FJSw) 4 4 465310 Adapter 90 (3/4 MOR x 3/4 JICM) 5 2 469866 Hose ½" x 230"
More informationHR24TS Rotary Rake. Serial Numbers and higher. Illustrated Parts Breakdown. Guards and Guard Arm, Front Hay Curtain Mount.
HRTS Rotary Rake Serial Numbers 00 and higher Illustrated Parts Breakdown Page Page Page Page Page Page Page Page Page Page 0 Page Page Page Page Page Page Page Page Page Page 0 Tongue Front Frame Guards
More informationTEXTRON Lycoming AIRCRAFT ENGINES
TEXTRON Lycoming AIRCRAFT ENGINES O-60-AP Wide Cylinder Flange Crankcase Model Engines PARTS CATALOG PC-06-6 MARCH 99 0-60-AP PARTS CATALOG This illustrated parts catalog contains a complete parts listing
More informationParts Manual. ProCut 20 Series 3-Wheel Riding Mower Serial No & Above. Models: H2220K R52 R61
Parts Manual ProCut 20 Series 3-Wheel Riding Mower Serial No. 7671 & Above Models: H2220K R52 R61 Ferris Industries 5375 North Main Street Munnsville, NY 13409 USA 800-933-6175 5022204 Revision 07 Rev.
More informationInstructions for Parts Books
Instructions for Parts Books The heading at the top of the page will be the same for the picture of the parts at it is for the page with the part numbers. Definition of column headings on part number pages:
More informationPARTS CATALOG ODYSSEY INCLUDES MOWER
PARTS CATALOG 8-3350 ODYSSEY INCLUDES MOWER INDEX PAINT ENGINES GENERAL INFO PRODUCT IDENTIFICATION NUMBERS (P.I.N.) OR SERIAL NUMBERS (S/N) ENGINE MODEL, SERIAL AND SPECIFICATION NUMBERS TRACTOR MODEL
More informationCOMPACT WHEEL LOADERS 7020, 7020BH Parts Catalog Ingersoll HOME TRACTORS ATTACHMENTS INDEX ENGINES GENERAL INFO. casecoltingersoll.
R Ingersoll COMPACT WHEEL LOADERS 7020, 7020BH Parts Catalog 8-3370 HOME TRACTORS ATTACHMENTS PAINT ENGINES GENERAL INFO PRODUCT IDENTIFICATION NUMBERS (PIN) AND SERIAL NUMBERS (S/N) TRACTOR MODEL AND
More informationInstructions for Parts Books
Instructions for Parts Books The heading at the top of the page will be the same for the picture of the parts at it is for the page with the part numbers. Definition of column headings on part number pages:
More informationDrive End Bracket & Bearing. Drive End Bracket. Tandem Axle # #865733
Drive End Bracket & Bearing #865089 1 06409700 1" Lock Collar 2 865733 Drive Bracket w/ Bearing 3 310037 End Drive Shaft Drive End Bracket #865733 1 03003100 Bearing 1" w/snap Ring 2 957795 Drive End Bracket
More informationPARTS CATALOG MUD HOG REAR WHEEL DRIVE
PARTS CATALOG MUD HOG REAR WHEEL DRIVE For Case IH AF 7230, 8230, 9230 Combines TUTHILL DRIVE SYSTEMS MODEL NUMBERS: CNH14023 DUAL SPEED KIT FOR CASE IH AF 7230, 8230, 9230 COMBINES A Product of Tuthill
More informationB436, B436E, B436SD WALK-BEHIND TROWEL
BARTELL MORRISON INC. 375 Annagem Blvd., Mississauga, ON L5T 3A7 Telephone: 1-905-364-4200 Toll Free: 1-866-501-1683 Fax: 1-905-364-4201 B436, B436E, B436SD WALK-BEHIND TROWEL Doc. # Orig. Rel. 06/2016
More informationLycoming AIRCRAFT ENGINES. IO-540-AC1A5 Wide Series Flange Crankcase Model Engine PARTS CATALOG PC
AIRCRAFT ENGINES IO-540-ACA5 Wide Series Flange Crankcase Model Engine PARTS CATALOG PC-5- November 008 Lycoming 5 Oliver Street Williamsport, PA 770 U.S.A. 570/33-8 IO-540-ACA5 PARTS CATALOG This illustrated
More informationReproduction. Not for. Large Frame Dual Stage Snowthrowers. Parts Manual
Parts Manual Attachment Mfg. No. Description 1695996-01 (SIH1428SE), 14.5TP 28" Dual Stage Snowthrower (CE/Export) Large Frame Dual Stage Snowthrowers 1695997-01 (SIH1730SE), 16.5TP 30" Dual Stage Snowthrower
More informationLYCOMING A Textron Company
LYCOMING AEIO-360-HB PARTS CATALOG This illustrated parts catalog contains a complete parts listing for the Lycoming AEIO-360-HB wide cylinder flange crankcase model aircraft engines. Major assembly and
More informationJOHN DEERE 9970 COTTON PICKERS
PARTS CATALOG FOR Mud Hog System II Rear Wheel Drive FOR JOHN DEERE 9970 COTTON PICKERS Mud Hog Model Numbers Tread Center OEM Aftermarket JD40005 JD47655 82, 90, 94, 106 TUTHILL Drive Systems 9098 West
More informationInstructions for Parts Books
Instructions for Parts Books The heading at the top of the page will be the same for the picture of the parts at it is for the page with the part numbers. Definition of column headings on part number pages:
More information4200 & 6200 Owner s Manual & Parts Book
00 & 00 Owner s Manual & Parts Book Purchase Date Serial Number Model Number Tractor Model PN: - Dealer Date --0 Description Page To The Owner & Maintenance Safety Precautions & Torque Specifications Skid
More informationO-540-A4B5 PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES
INTRODUCTION This illustrated parts catalog contains a complete parts listing for the Lycoming O-540-A4B5 wide cylinder flange crankcase model aircraft engines. Major assembly and sub-assembly parts of
More informationIllustrated Parts List
Spicer Steer Axles Illustrated Parts List Spicer EFA Family AXIP-0074 February 2008 Table of Contents Table of Contents Introduction...2 About this Parts Book...2 Abbreviations...2 Genuine Spicer Parts...2
More informationReproduction. Not for. Mid Frame Dual Stage Snowthrowers. Parts Manual
Parts Manual Attachment Mfg. No. Description 1695821 (I1224E), 11.5TP 24" Dual Stage Snowthrower 1695842 (I924EX), 9TP 24" Snowthrower (CE/Export) Mid Frame Dual Stage Snowthrowers Not for Reproduction
More informationCOMPACT WHEEL LOADERS before PIN BH - before PIN Parts Catalog Ingersoll HOME TRACTORS ATTACHMENTS INDEX ENGINES
R Ingersoll HOME COMPACT WHEEL LOADERS 6018 - before PIN 14190349 6018BH - before PIN 14190351 Parts Catalog 8-3052 TRACTORS ATTACHMENTS INDEX PAINT ENGINES GENERAL INFO PRODUCT IDENTIFICATION NUMBERS
More informationParts Manual FRONT-FOLD BOOMS MODELS 80, 90 & 100 HYDRAULIC FOR TA1200 & TA1600 SPRAYERS. Serial Number B & Higher. Part No.
Parts Manual FRONT-FOLD BOOMS MODELS 80, 90 & 100 HYDRAULIC FOR TA1200 & TA1600 SPRAYERS Serial Number B30970200 & Higher Part No. 408920 Front-Fold Booms 80 / 90 / 100 Introduction Foreward This symbol
More informationPARTS LIST INTRAAX AANT230 ZMD TRAILER SUSPENSION SYSTEM. LIT NO: DATE: November 2018 REVISION: B
PARTS LIST INTRAAX AANT30 ZMD TRAILER SUSPENSION SYSTEM LIT NO: 97114-117 DATE: November 018 REVISION: B INTRAAX AANT30 ZMD TRAILER SUSPENSION SYSTEMS PARTS LIST TABLE OF CONTENTS INTRODUCTION 3 ABBREVIATIONS
More informationAGRIMETAL ASSEMBLY CASING ASSEMBLY : CREATION : REVISION : AUTHOR : S.B. Page 1 de 15
PARTS LIST BW 00 --00 # PART # Qty TITLE -0-000 BLOWER CASING (B.W.00 POINTS) NC-6-00 BUSHING 0.80'' ID X.0'' OD X 0.60'' --00 SERIAL NUMBER PLATE ASSEMBLY CASING ASSEMBLY : --00 CREATION : 06-06- REVISION
More informationPARTS LIST. Reproduction. Not for. Mower Decks. Mfg. No. Description EZM2042, 20HP B&S w/42" Mower Deck (2009)
PARTS LIST Mower Decks Mfg. No. Description 7800490 EZM2042, 20HP B&S w/42" Mower Deck (2009) Manual Part No. Revision A Rev. Date: 11/5/2009 Table Of Contents PRODUCT COMPONENTS PAGES Frame, Body & Seat
More informationBUSH HOG LAND MAINTENANCE REPAIR PARTS MANUAL MODELS: RPM & RPM SECTION: 79
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODELS: -0 RPM & -000 RPM SECTION: 9 0 Griffin Ave. Selma, Al. 0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com April, 0 BUSH HOG/ LAND MAINTENANCE
More information2 Cylinder Grapples. Model Number.
Cylinder Grapples SGV STG SRGV HSRGV SBG ISG TBG Model Number. Serial Number. Serial Number 0400-059 AND 0609, 0630, 0735, 0736, 0737, 0750, 075, 09, 00, 0, 0, 03, 09,09, 074, 075, 076, 077, 90 Manufacture
More informationParts Manual. Models Mfg. No. Description Brute, 14.5TP 29" Dual Stage Snowthrower (2012)
Parts Manual Models Mfg. No. Description 1696282-00 Brute, 14.5TP 29" Dual Stage Snowthrower (2012) Manual Part No. 1756728 Revision C Rev. Date: 8/21/2013 Table Of Contents PRODUCT COMPONENTS PAGES Handles
More information4. TRANSMISSION 1. SAFETY 2. PREPARATION 3. FRAME 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT Monosem Inc.
TABLE OF CONTENTS 1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT TRANSMISSION 3-point Mounted, 7" x 7", and Stacking Toolbar Frame PLANTING RATE CHART 3pt
More informationReproduction. Not for PARTS MANUAL. Models
PARTS MANUAL Models Mfg. No. Description 881029 MXMH625, 6.25TP 19" High Wheel Self-Propelled Mulching Mower, CE (2010) 881153 MXMH650E, 19" High Wheel Self-Propelled Mulching Mower, CE (2010) 881154 MXMH850E,
More informationCOMPACT WHEEL LOADERS PIN and after 6018BH - PIN and after 6020L, 6020BH Parts Catalog
R Ingersoll HOME COMPACT WHEEL LOADERS 6018 - PIN 14190349 and after 6018BH - PIN 14190351 and after 6020L, 6020BH Parts Catalog 8-3360 TRACTORS ATTACHMENTS INDEX PAINT ENGINES GENERAL INFO MAIN INDEX
More informationReproduction. Not for. Mid Frame Dual Stage Snowthrower. Parts Manual
Parts Manual Attachment Mfg. No. Description 1695994 (I924EX), 9TP 24" Snowthrower (CE/Export) Mid Frame Dual Stage Snowthrower Not for Reproduction Manual Part No. Revision - Rev. Date: 7/20/2011 Table
More informationMulching and Finishing Mowers MP and FP
Mulching and Finishing Mowers MP and FP Parts Manual Locke Turf 0 Highway E, Opp, Alabama, () -00 Transport Wheel, Tire & Spindle MP and FP ALPHABETICAL INDEX CONTENTS PAGE 00 Hydraulic Cylinder (Rear)
More informationPARTS MANUAL. HD4SR and 12SR Auto Align Bale Skoop to 2017 K
PARTS MANUAL 1998 to 2017 HD4SR and 12SR Auto Align Bale Skoop K34991-04 Table of Contents Section 1: Parts Breakdown...1-1 Bale Skoop Final Assembly... 1-2 Loader Assembly... 1-4 12SR - Grab Hook Assembly
More informationSPARE PARTS BOOK. Rear Tandem Axle FRDP FRDP16S0879/011&013 Up to S/N (Nov 2004) Book No. 247 (2/2007)
SPARE PARTS BOOK Rear Tandem Axle ) Sisu Axles, Inc. Autotehtaantie 1 PO Box 19 FIN-101 Hameenlinna Finland Phone +35 20 55 99 Fax +35 20 55 00 2.2.2007 1 Axle L71 2 1 5 3 9 7 10 11 1 1 15 Breather 1 Breather
More informationO-540-F1B5 SERIES PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES
INTRODUCTION This illustrated parts catalog contains a complete parts listing for the Lycoming O-540-F1B5 series wide cylinder flange crankcase model aircraft engines. Major assembly and sub-assembly parts
More informationParts Manual. Fast-Vac Grass Collection Systems Fits 2004 Models & Prior with Steel Discharge Chute
Parts Manual Fast-Vac Grass Collection Systems Fits 2004 Models & Prior with Steel Discharge Chute Models: Description: 5600021 48" 3-Bag System (1000Z Series) 5600022 48" 3-Bag System (IS1000Z Series)
More informationPARTS CATALOG FOR. Mud Hog Rear Wheel Drive FOR. MF 9540/9550/9560, CAT 540C/550C/560C, Gleaner A540/A560, Fendt 6450R/9480R COMBINES
PARTS CATALOG FOR Mud Hog Rear Wheel Drive FOR MF 9540/9550/9560, CAT 540C/550C/560C, Gleaner A540/A560, Fendt 6450R/9480R COMBINES Mud Hog Model Number: AG9896 A Product of Tuthill Drive Systems P.O.
More informationWX970 Trailer Log Splitter Parts Manual
EMB Manufacturing Inc. 4144 Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) 699-9283 Fax: (519) 699-4146 www.embmfg.com WX970 Trailer Log Splitter Parts Manual S/N 2E9US1110ES370010 & After 370010
More informationParts Manual. Trailed Track System (TTS) 70 Series ( , , ) 80 & 100 Series ( , , includes )
Parts Manual Trailed Track System (TTS) 70 Series (70-2516, 70-3011, 70-3611) 80 & 100 Series (100-3612, 100-3613, includes 80-3013) CPB-513 March 2014 TABLE OF CONTENTS FOREWORD...............................................................2
More informationPARTS LIST. Reproduction. Not for. Models Mfg. No. Description Pico 6, SP 44cm Walk Behind, CE (2010)
PARTS LIST Models Mfg. No. Description 884142 Pico 6, SP 44cm Walk Behind, CE (2010) Manual Part No. 1739809 Revision B Rev. Date: 1/13/2011 Table Of Contents PRODUCT COMPONENTS PAGES Handle, Controls
More informationReproduction. Not for. Parts Manual. 43cc 2-Cycle. Mini Cultivator
Parts Manual Attachment Mfg. No. Description 1695764 Roticul, 43cc 2 Cycle Mini Cultivator 1695920 Roticul, 43cc 2 Cycle Mini Cultivator 43cc 2-Cycle Not for Mini Cultivator Reproduction Manual Part No.
More informationLAND MAINTENANCE REPAIR PARTS MANUAL BUSH HOG MODEL: 307 SECTION: 16
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODEL: 0 SECTION: P.O. Box 0 Selma, AL 0-0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com BUSH HOG / LAND MAINTENANCE REPAIR S MANUAL SEPTEMBER, 0
More informationMOBILE MIXERS PARTS MANUAL HIGH ROUGHAGE, STATIONARY, TRUCK & TRAILER MODELS. Serial number up to
MOBILE MIXERS PARTS MANUAL 405-470 - 540 HIGH ROUGHAGE, STATIONARY, TRUCK & TRAILER MODELS Serial number up to Harsh International, Inc. 600 Oak Ave. Eaton, CO 80615-0007 (970) 454-2291 Fax: (970) 454-3491
More informationBale Grabber BG2400 & BGE P Parts Manual. Copyright 2018 Printed 01/19/18
Bale Grabber BG2400 & BGE2400 70352 319-173P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.
More information