ELECTRIC MOTORS 3SIE IE3
|
|
- Laureen Hart
- 5 years ago
- Views:
Transcription
1 EECTRIC MOTORS 3SIE IE3
2 TECHNIC INFORMTION TYE 3SIE IE3 Construction 3SIE have a stator house in aluminum from frame End shields are in aluminum in frame and in cast iron from frame 112. Flanges are in cast iron from frame 90. From frame 132 and up is the stator house in cast iron and also the end shields. Normally have foot motors in pole execution roller bearing on drive side while 2 pole, flange- and foot/flange motors have ball bearings as standard. The motors are produced according to IEC : 2008, IEC :2007 and IEC :2014. Standard are SS-EN IEC and motors are marked with CE. Voltage and Frequency Motors are available for frequencies of and at standard voltage. Special voltage on request. The voltage can vary up to +/- 5%, without derating. Maintenance In normal use maintenance is limited to greasing of the bearings. ll motors in sizes 200 and larger are fitted with grease nipples as standard. The bearings are lubricated with lithium based grease class11. Smaller motors have closed bearing housings and sealed bearings, and can be considered maintenance free. For hard opens special bearings can be supplied for example, for high ambient temperature and increased. Voltage Three phase single motors can normally be connected for two different voltage ranges (connection in star higher voltage, or delta lower voltage) with a of 3. This gives a wide application range and simplified management of ordering and stockholding V Star V Delta The above connection diagrams are applicable to range wound motors for supplies of V (Delta connection) and V (Star connection). Examples: a) V Delta/ V Star may be labelled 230/400 V (Standard for motors 3 and smaller). Suitable for direct on line starting on V supplies. b) V Delta/ V Star may be labelled 400 V Delta (Standard for motors 4 and larger). Suitable for Star/Delta starting on volt supplies or direct on line starting on V supplies. Frequency Motors wound for supplies can also be used on. Rated data can be calculated from the table below. Voltage at Voltage at data as % of data Torque M Mst Speed n Balancing Motors are balanced with a half key. Special degrees of balancing are available on request. Standards Motor construction, outputs, and fixing dimensions comply with IEC standards. Thermistors rotection is provided fitted in frame 160 and up. Thermistors are temperature sensitive resistors that at a certain temperature have a wide change of resistance. When connected with sensing relay it can be used to e.g. cut of the supply to main contactor coil. Cooling s standard, the fan and cowl is fitted at the non-drive end (cooling form IC 411). Other cooling methods can be supplied e.g. separately driven cooling fan (often used with inverter drives). Heaters Motors used in conditions of wide temperature variation or extreme climatic conditions can be damaged by condensation and dampness in the windings. In motors fitted with heaters, the windings are heated to a few degrees above ambient, which is enough to prevent condensation. Heaters must not be energised when the motor is running. Smaller motors can be heated by supplying a low voltage via the motor leads, using a supply of 5-10% of the rated voltage between two phases. BEVI can fit heaters to all motor sizes. mbient Temperature The motors can operate at ambient 40 degrees and for Marine applications at 45 degrees if the motor not are placed over 1000 meter over the sea. Duty Motors are designed for S1 duty. The motors can also be used for S2-S9 duty. Vibn Speed The vibn complies with Class of IEC as standard. Class B can also be met if required by customer. Noise evel The noise level complies with IEC as standard. Recycling arger motors can advantageously be renovated. The motors will otherwise be treated as electronic waste in accordance with national laws and regulations. The motors can be recycled at very high extent. Mounting arrangements Foot mounting B3 V5 V6 IM 1001 IM 1011 IM 1031 Face mounting B14 V18 V19 IM 3601 IM 3611 IM 3631 STNDRD SS-EN IEC STNDRD EFFICIENCY IEC : 2008 IEC : 2007 IEC : 2014 Foot mounting B6 B7 B8 IM 1051 IM 1061 IM 1071 Flange mounting B5 V1 V3 IM 3001 IM 3011 IM 3031 Enclosure (degree of protection) Motors are produced in degree of protection I55 as standard, but are also available to other standards. Insulation Class ll motors are wounded with Class F material, but calculated with temperature rise according to class B at. Foot & flange mounting B3/B5 V15 V36 IM 2001 IM 2011 IM 2031 Foot and face mounting B3/B14 V18 V19 IM 2101 IM 2111 IM 2131
3 EECTRIC MOTORS TYE 3SIE IE3 2 poles 3000 Number of poles () Efficiency 230V 400V 525V 460V 100% IE3 75% 50% factor Cos la/ln Ma/Mn ull out Mmax/Mn Moment of inertia (J) kgm SIE SIE 80-2B SIE 90-S SIE SIE SIE 112-M SIE 132-S SIE 132-S2B SIE 160-M SIE 160-M2B SIE SIE 180-M SIE SIE 200-2B SIE 225-M SIE 250-M SIE 280-S SIE 280-M SIE 315-S SIE 315-M SIE 315-M2B SIE 315-M2C Mass (B3) kg EECTRIC MOTORS TYE 3SIE IE3 4 poles 1500 Number of poles 1500 () Efficiency 230V 400V 525V 460V 100% IE3 75% 50% factor Cos la/ln Ma/Mn ull out Mmax/Mn Moment of inertia (J) kgm 2 3SIE 80-4B SIE 90-S SIE SIE SIE 100-4B SIE 112-M SIE 132-S SIE 132-M SIE 160-M SIE SIE 180-M SIE SIE SIE 225-S SIE 225-M SIE 250-M SIE 280-S SIE 280-M SIE 315-S SIE 315-M SIE 315-M4B SIE 315-M4C Mass (B3) kg We reserve the right to make design changes.
4 EECTRIC MOTORS TYE 3SIE IE3 6 poles 1000 Number of poles () Efficiency 230V 400V 525V 460V 100% IE3 75% 50% factor Cos la/ln Ma/Mn ull out Mmax/Mn Moment of inertia (J) kgm SIE 90-S SIE SIE SIE 112-M SIE 132-S SIE 132-M SIE 132-M6B SIE 160-M SIE SIE SIE SIE 200-6B SIE 225-M SIE 250-M SIE 280-S SIE 280-M SIE 315-S SIE 315-M SIE 315-M6B SIE 315-M6C SIE 315-M6D Mass (B3) kg EECTRIC MOTORS 8 poles 750 Outside the IE2 and IE3 norms Number of poles () V V 525V 230V 400V V 460V Efficiency factor Cos la/ln Ma/Mn ull out Mmax/Mn Moment of inertia (J) kgm % Sh Sh 63-8B Sh Sh 71-8B Sh 71X-8C* Sh Sh 80-8B Sh 80X-8C* Sh 80X-8D* ISSh 90S ISSh ISSg ISSg 100-8B ISSg 112M ISSg 132S ISSg 132M ISSg 160M ISSg 160M-8B ISSg ISSg Sg Sg 225S Sg 225M Sg 250M Sg 280S Sg 280M Sg 315S Sg 315M Sg 315M-8B Sg 315M-8C Sg 355S SEE 355M SEE 355M-8B * rogressive motors. For drawings on 8 pole motors see page 40 in our catalogue or website. We reserve the right to make design changes. Mass (B3) kg
5 DIMENSION DRWING FOOT MOTORS TYE 3SIE IE3 B3 Frame size Frame size bw bw H H HD D - G F H H HD E C B K B1 B2 K BB E C B B B1 B BB Mounting arrangement B3 Type B C D E F G H bw K B BB H HD 3SIE j6 40 6h xM20x SIE 80-.B j6 40 6h xM20x SIE 90S j6 50 8h xM20x SIE 90-2, j6 50 8h xM20x SIE 90S-4, j6 50 8h xM20x SIE j6 50 8h xM20x SIE 100-2, j6 60 8h xM20x SIE 100-4,4B j6 60 8h xM20x SIE 112M-2,4, j6 60 8h xM25x SIE 132S k h xM25x SIE 132M k h xM25x SIE 160M k h xM40x SIE k h xM40x SIE 180M-2, k h xM40x SIE 180-4, k h xM40x Type B B1 C D E F G bw H H K B B1 B2 BB HD 3SIE xM SIE 225S xM SIE 225M xM SIE 225M xM SIE 250M xM SIE 250M xM SIE 280S xM SIE 280S xM SIE 280M xM SIE 280M xM SIE 315S xM SIE 315S xM SIE 315M2;B xM SIE 315M4;B; xM SIE 315M6B xM SIE 315M2C xM SIE 315M4C xM SIE 315M6C xM SIE 315M6D xM SIE 355 M (2) xM SIE 355 M (4, 6) xM SIE 355 H (2) xM SIE 355 H (4, 6) xM Motors with termistors have also one extra gland M16. Size and type of bearings Motor type 2-poles motors (3000 ) 4, 6 and 8-poles motors (1500, 1000, 750 ) -(driving)side B-side -(driving)side B-side 3SIE Z C Z C Z C Z C3 3SIE Z C Z C Z C Z C3 3SIE Z C Z C Z C Z C3 3SIE Z C Z C Z C Z C3 3SIE Z C Z C Z C Z C3 3SIE Z C Z C Z C Z C3 3SIE Z C Z C Z C Z C3 -side B-side -side B3 B-side -side B5, B3/B5 3SIE C C3 NU312 C C C3 3SIE C C3 NU313 C C C3 3SIE C C3 NU315 C C C3 3SIE C C3 NU318 C C C3 3SIE 315 S, M, MB 6315 C C3 NU318 C C C3 3SIE 315 MC, MD 6316 C C3 NU320 C C C3 We reserve the right to make design changes.
6 DIMENSION DRWING FNGE MOTORS TYE 3SIE IE3 B5 Frame size Frame size B14 T T E HB - N D N F HB G E S E S Mounting arrangement IM B5, IM V1 Type D E F G M N T HB S (ø) S (hole) 3SIEK j6 40 6h j SIEK 80-.B 19j6 40 6h j SIEK 90S-2 24j6 50 8h j SIEK 90-2,6 24j6 50 8h j SIEK 90S-4,6 24j6 50 8h j SIEK j6 50 8h j SIEK 100-2,6 28j6 60 8h j SIEK 100-4,4B 28j6 60 8h j SIEK 112M-2,4,6 28j6 60 8h j SIEK 132S 38k h j SIEK 132M 38k h j SIEK 160M 42k h j SIEK k h j SIEK 180M-2,4 48k h j SIEK 180-4,6 48k h j SIEK SIEK 225S SIEK 225M SIEK 225M SIEK 250M SIEK 250M SIEK 280S SIEK 280S SIEK 280M SIEK 280M SIEK 315S2* SIEK 315S4-6* SIEK 315M2;B* SIEK 315M4;B;6* SIEK 315M6B* SIEK 315M2C* SIEK 315M4C* SIEK 315M6C* SIEK 315M6D* SIEK 355 M (4-6)* 100m h SIEK 355 H (4-6)* 100m h * Only for vertical mounting. Mounting arrangement IM B14 We reserve the right to make design changes. Type Flange D E F G M N S T E HB 3SIEK B14/C1 19j6 40 6h j6 160 M SIEK B14/C2 19j6 40 6h j6 120 M SIEK 80-.B1 B14/C1 19j6 40 6h j6 160 M SIEK 80-.B2 B14/C2 19j6 40 6h j6 120 M SIEK 90S 2 B14/C1 24j6 50 8h j6 160 M SIEK 90S 2 B14/C2 24j6 50 8h j6 140 M SIEK 90 2,6 B14/C1 24j6 50 8h j6 160 M SIEK 90 2,6 B14/C2 24j6 50 8h j6 140 M SIEK 90S 4,6 B14/C1 24j6 50 8h j6 160 M SIEK 90S 4,6 B14/C2 24j6 50 8h j6 140 M SIEK 90 4 B14/C1 24j6 50 8h j6 160 M SIEK 90 4 B14/C2 24j6 50 8h j6 140 M SIEK 1002,6 B14/C1 28j6 60 8h j6 200 M SIEK 1002,6 B14/C2 28j6 60 8h j6 160 M SIEK 1004,4B B14/C1 28j6 60 8h j6 200 M SIEK 1004,4B B14/C2 28j6 60 8h j6 160 M SIEK 112M2,4,6 B14/C1 28j6 60 8h j6 200 M SIEK 112M2,4,6 B14/C2 28j6 60 8h j6 160 M SIEK 132S B14/C1 38k h j6 250 M SIEK 132S B14/C2 38k h j6 200 M SIEK 132M B14/C1 38k h j6 250 M SIEK 132M B14/C2 38k h j6 200 M
7 DIMENSION DRWING FOOT/FNGE MOTORS TYE 3SIE IE3 B35 Frame size Frame size T T S HD - F S N D N HD H H G H H E C B BB K B E B1 C B B1 BB B2 B K Mounting arrangement IM B35 Type B C D E F G H K M N S T B BB H HD 3SIE j6 40 6h j SIE 80-.B j6 40 6h j SIE 90S j6 50 8h j SIE 90-2, j6 50 8h j SIE 90S-4, j6 50 8h j SIE j6 50 8h j SIE 100-2, j6 60 8h j SIE 100-4,4B j6 60 8h j SIE 112M-2,4, j6 60 8h j SIE 132S k h j SIE 132M k h j SIE 160M k h j SIE k h j SIE 180M k h j SIE k h j Type B B1 C D E F G H H K B B1 B2 BB HD M N T S Ø Hole 3SIE SIE 225S SIE 225M SIE 225M SIE 250M SIE 250M SIE 280S SIE 280S SIE 280M SIE 280M SIE 315S SIE 315S SIE 315M2;B SIE 315M4;B; SIE 315M6B SIE 315M2C SIE 315M4C SIE 315M6C SIE 315M6D SIE 355 M (2) SIE 355 M (4,6) SIE 355 H (2) SIE 355 H (4,6) We reserve the right to make design changes.
8 Östermovägen Sundsvall Tel:
9
ELECTRIC MOTORS 3SIE IE3
TRI OTOR 3I I3 THI IFORTIO TY 3I I3 onstruction 3I have a stator house in aluminum from frame 80-112. nd shields are in aluminum in frame 80-100 and in cast iron from frame 112. Flanges are in cast iron
More informationGeneral Purpose Energy Efficient Induction Motors series 2SIE
General Purpose Energy Efficient Induction Motors series 2SIE Comply with the new efficiency classes for low-voltage three-phase motors IEC 60034-30 standard and EU Regulation 640/2009 Product Catalogue
More informationEnergy Saving Three Phase Motors
e-drive Energy Saving Three Phase Motors IEC frames 56 to 400 Outputs 0.09 to 630 IE2 MEPS2006 Type: AHE Aluminium Motors Type: HE Cast-Iron Motors 1 When you need all the features of a premium quality
More informationSWE SERIES (IE3) WONDER ELECTRIC MOTOR (S) PTE LTD. Energy Saving Low Noise Environmental Friendly IEC Dimension Low Vibration European Design
RANGE OF PRODUCTS Three phase asynchronous squirrel-cage & slip ring induction motors Three phase asynchronous self-braking motors Hollow shaft rotor motors Cooling tower motors High motors, (IE2) (IE3)
More informationSeries E4F E5F
Three Phase Induction Motors With Rotors Wound for Hoists Series E4F 160-315 E5F 355-400 ASI NT 003.1 I N D E X Use 2 Electrical Tolerances 9 Mechanical Tolerances 9 General Characteristics 2 Technical
More information: B3; B5; B14; B34; B35; V1
ATT WE series (Eff1) are 3-phase TEFC Cast-Iron high efficiency general purpose induction motors, which are designed to meet or exceed the requirements for energy efficiency such as: European Eff1, Australia
More informationAEEB AEVB LOW VOLTAGE SERIES Three-Phase Squirrel Cage Induction Motor Conforming to SS530 (Occasional Use) Conforming to IE1
AEEB AEVB LOW VOLTAGE SERIES Three-Phase Squirrel Cage Induction Motor Conforming to SS530 (Occasional Use) Conforming to IE1 STANDARD AND SPECIFICATION Performance: Meet the requirement of Singapore standard
More informationMINING ELECTRIC MOTORS 3KTCR, 4KTCR, 5KTCR
MINING ELECTRIC MOTORS 3KTCR, 4KTCR, 5KTCR Explosion protection Certificate of Conformity: Frame size 71 and 160 Frame size 80, 90, 100, 112, 132 Frame size 180, 200, 225 Frame size 250 Frame size 280
More informationStandard cast iron Motor
Standard cast iron Motor Frame size 80 to 355 Série 1L Phase 3 Voltage 265/460V 60Hz Types of mounting B3 V9 B5 B14 B6 B9 B3 / B5 V5 B3 / B14 B15 V1 B7 V18 V1 / V5 V8 V18 / V5 V6 B8 V3 / V6 V3 V19 V19
More informationProduct Catalogue. General Purpose 3-phase Induction Motors. Energy Efficient Motors series 2SIE
General Purpose 3phase Induction Motors Energy Efficient Motors series SIE Comply with the new efficiency classes for lowvoltage threephase motors IEC 6003430 standard and EU Regulation 640/009 Product
More informationGeneral Purpose Cast Iron Motors
General Purpose Cast Iron Motors Totally enclosed squirrel cage three phase low voltage motors, Sizes 71-355, 0.25 to 250 kw www.abb.com/motors&drives > Motors > Low voltage motors > General purpose motors
More informationIEC Low Voltage Induction Motors 400 V 50 Hz. Motors for all applications
IEC Low Voltage Induction Motors 400 V 50 Hz Motors for all applications Making you more competitive BB has been manufacturing motors for over 100 years. Our products are designed to be reliable, effi
More informationGeneral Purpose Energy Efficient Induction Motors series 2SIE
General Purpose Energy Efficient Induction Motors series 2SIE Comply with the new efficiency classes for low-voltage three-phase motors IEC 60034-30 standard and EU Regulation 640/2009 Product Catalogue
More informationSINGLE PHASE TEFC CAGE MOTORS
SINGLE PHASE TEFC CAGE MOTORS 2 SINGLE PHASE TEF CAGE MOTORS Mechanical protection: IP 54 Voltage: 220 V, 50 Hz Type Output power P N kw Rated speed n N min -1 Efficiency % Power factor cos Rated current
More informationMINING ELECTRIC MOTORS 3KTCR AND 4KTCR
MINING ELECTRIC MOTORS 3KTCR AND 4KTCR Explosion protection Certificate of Conformity: Frame size 71 and 160 Frame size 80, 90, 100, 112, 132 Frame size 180, 200, 225 Frame size 250 Frame size 280 Frame
More informationFrom 16 June 2011, motors placed for the first-time on the market shall have a minimum efficiency class of IE2.
INTRODUCTION New efficiency classes for the low-voltage three-phase motors (IE = International Efficiency). Along with the international discussion on energy efficiency a worldwide harmonized energy efficiency
More informationTechnical Documentation
Technical Documentation LOW VOLTAGE THREE PHASE TEFC CAGE MOTORS IE316EN Mission, Vision, Targets Our electric motors and generators are optimized in accordance with our client's technical and economical
More informationCatalog Mars Low voltage Brake motors
Catalog Mars 2014 Low voltage Brake motors We provide motors, generators and mechanical power transmission products, services and expertise to save energy and improve customers processes over the total
More informationOrdering information. When placing an order, specify motor type, size and product code according to the following example.
Ordering information When placing an order, specify motor type, size and product code according to the following example. Example Motor type M3AA 112 MB Pole number 4 Mounting arrangement (IM-code) IM
More informationchampion series motors
Introducing A brand new series of Super Performers Data Sheet champion series motors FRAME SIZE 63-132M TEFC 3 Phase Squirrel Cage Induction Motors Siemens CHAMPION Series Cage Motors are suitable for
More informationTechnical Documentation
Technical Documentation LOW VOLTAGE THREE PHASE TEFC CAGE MOTORS IE315EN Mission, Vision, Targets Our electric motors and generators are optimized in accordance with our client's technical and economical
More informationGeneral Purpose 3-Phase Induction Motors
General Purpose 3Phase Induction Motors 008 Product Catalogue General Purpose 3Phase Induction Motors Certificates Cantoni Motor S ISO 900 KEM Since September 30, 999 Number 9955 Besel S ISO 900 DQS Since
More informationA6C A5C-B6C B5C B5H A6C A5C B6C B5C B5H. Model. Up to kw. Power. Up to V. Voltages. Model IP55. Frame Pole 2, 4, 6, 8 and 10
A6C A5C-B6C B5C B5H Model Power Voltages Model IP55 A6C A5C B6C B5C B5H Up to 2.400 kw Up to 11.000 V LV A6C - B6C - A5C - B5C MV B5H Frame 71 560 Pole 2, 4, 6, 8 and 10 Cooling IC 411 ( IC 416 optional)
More informationELECTRIC MOTORS. Selection. Starting torque and nominal torque
SELECTION PROCEDURE The output powers published overleaf are based upon continuous maximum rating conditions. Therefore design factors for above average running periods do not normally affect the selection.these
More informationLow Voltage 3-Phase Induction Motors. Range 0.18kW to 670kW
Low Voltage 3-Phase Induction Motors Range 0.18kW to 670kW Totally Enclosed Fan-Cooled Cast Iron Series Contents page page PRODUCT DETAILS General Information 2 Electrical Design and Standards Altitude
More informationLow Voltage Induction Motors
Low Voltage Induction Motors Catalogue-2009/04 E TAC-C CAST IRON Frame Size 71->355 0,18-315 kw t-telectric.com Technical features TAC-C motors are designed and manufactured according to IEC34, IEC72,
More informationIEC Low Voltage Induction Motors 400 V 50 Hz. Motors for all applications
IEC Low Voltage Induction Motors 400 V 50 Hz Motors for all applications Making you more competitive ABB has been manufacturing motors for over 100 years. Our products are designed to be reliable, effi
More informationLARGE THREE-PHASE SQUIRREL CAGE ASYNCHRONOUS MOTORS FOR HEAVY DUTY APPLICATIONS ADH SERIES
LARGE THREE-PHASE SQUIRREL CAGE ASYNCHRONOUS MOTORS FOR HEAVY DUTY APPLICATIONS ADH SERIES FRAMES 355 560 355kW 1500kW (1500rpm) FOR INVERTER DUTY Code Declaration of conformity The motors described in
More informationProcess performance IE3 aluminum motors, 50/60 Hz The product range for global customers
PRODUCT NOTE Process performance IE3 aluminum motors, 50/60 Hz The product range for global customers BB offers its premium aluminum motor range in frame sizes 80-250 that meets the need of the global
More informationANNEX No 1. C 17/05/2006 SGA112B TERMINAL BOX ARRANGEMENT Ex e, Ex na &Ex td V (OPTION 2)
ANNEX No 1 DRAWINGS Drawing No. Drawing Description Revision Date Ex e, na and td SGA100A General Arrangement for SGA 71 frame motor C 16/06/2006 SGA101A General Arrangement for SGA 80-132 frame motor
More informationSquirrel Cage Induction Motors MA - A4 - BB - B4 - B5 SERIES SIZES. MarelliMotori ASI.CT.033.2
Marine Motors Three Phase Squirrel Cage Induction Motors MA - A4 - BB - B4 - B5 SERIES 63-400 SIZES MarelliMotori ASI.CT.033.2 CONTENTS Page STANDARDS 5 ESSENTIAL AND NON-ESSENTIAL SERVICE 5 CLASSIFICATION
More informationCatalog. Low voltage General performance IE2 high efficiency motors according to EU MEPS
Catalog Low voltage General performance IE2 high efficiency motors according to EU MEPS We provide motors, generators and mechanical power transmission products, services and expertise to save energy and
More informationGeneral performance IE3 cast iron motors in frame sizes 71 to 355
PRODUCT NOTE General performance IE3 cast iron motors in frame sizes 71 to 355 General performance IE3 motors are ideal for OEMs to build into pumps and fans, as well as for other applications including
More informationMARATHON SLA SERIES CAST ALUMINIUM MULTI-MOUNT THREE PHASE MOTORS SIZES , KW
MARATHON SLA SERIES CAST ALUMINIUM MULTI-MOUNT THREE PHASE MOTORS SIZES 56-160, 0.09-18.5KW MARATHON SLA SERIES CAST ALUMINIUM MULTI-MOUNT THREE PHASE MOTORS SIZES 56-160, 0.09-18.5KW INTRODUCTION 3 Standards
More informationAESV / AESU / AESV-LA Series Squirrel Cage Induction Motor AESV1S / AESU1S / AESV1S-LA (IE1) STANDARD EFFICIENCY
AESV / AESU / AESV-LA Series Squirrel Cage Induction Motor AESV1S / AESU1S / AESV1S-LA (IE1) STANDARD EFFICIENCY AESV2S / AESU2S / AESV2S-LA (IE2) HIGH EFFICIENCY AESV3S / AESU3S / AESV3S-LA (IE3) PREMIUM
More informationA B C D, E, F M2BA 112 MB 3GBA ADB, 122, 451, etc
Ordering information When placing an order, please state the following minimum data in the order, as in the example. The product code of the motor is composed in accordance with the following example.
More informationAsynchronous, Low Voltage, Squirrel Cage, Three Phase Electric Motors
Asynchronous, Low Voltage, Squirrel Cage, Three Phase Electric Motors Series R2, Frame 63 355 Introduction KHM R2 series cast iron motors are totally enclosed fan cooled, 3 phase, and squirrel cage induction
More informationGeneral Specifications. Cooling Method 3M series are IC 411 Standard. IC 416, IC 418 can be provided Upon request
3M SERIES Three Phases Low Voltage Asynchronous Motors 3M Series Vilma motors are designed and manufactured with high quality materials and workmanship in order to meet demanding and arduous operation
More informationKAT.NMST ENG NORM ELECTRIC MOTORS THREE PHASES SQUIRREL CAGE TEFC NMST
KAT.NMST.02.14.ENG NORM ELECTRIC MOTORS THREE PHASES SQUIRREL CAGE TEFC NMST 90 355 IMPORTANT NOTE: Due to the continious development policy, our companyreserves the right to make changes the values, dimensions
More informationCompany name: GSI Created by: SLK Phone: (65) Date: 13/03/2017 Client: Client Number: Contact:
Qty. Description 1 2L Product No.: 81U1332 The motor is a 3-phase AC standard motor. Installation: Range of ambient temperature: -2.. C Flange size for motor: FF Note! Product picture may differ from actual
More informationMARATHON HLA SERIES HLA CAST ALUMINIUM MULTI-MOUNT THREE PHASE MOTORS SIZES , KW
MARATHON HLA SERIES HLA CAST ALUMINIUM MULTI-MOUNT THREE PHASE MOTORS SIZES 80-160, 0.75-18.5KW MARATHON HLA CAST ALUMINIUM MULTI-MOUNT THREE PHASE MOTORS SIZES 80 TO 160, 0.75 TO 18.5KW INTRODUCTION 3
More informationTHREE-PHASE ASYNCHRONOUS MOTORS EFFICIENCY CLASS ACCORDING IEC
THREE-PHASE ASYNCHRONOUS MOTORS EFFICIENCY CLASS ACCORDING IEC 60034-30 1st EDITION IE1/IE2-MS IE1/IE2-EG Series IE1 Standard efficiency IE2 High efficiency THREE-PHASE ASYNCHRONOUS MOTORS EFFICIENCY CLASS
More informationDrive IT Low Voltage Cast Iron Motors. M2000 Range
Drive IT Low Voltage Cast Iron Motors M2000 Range Making you more competitive ABB has been manufacturing motors for over 100 years. Our products are designed to be reliable, efficient and cost effective,
More informationM3000 Motors for Hazardous Areas. Low Voltage Non-sparking Motors Ex na, EEx na
M3000 Motors for Hazardous Areas Low Voltage Non-sparking Motors Ex na, EEx na Non-sparking EEx na, Ex na, Ex N Range Standards Frame Size Output range Non-sparking Ex na IEC 60079-15 aluminium 90-250
More informationLow Voltage General Purpose Motors
Low Voltage General Purpose Motors Making you more competitive ABB s General purpose motor is designed for use in general industry, meeting the demands of standard applications for OEM's. Motors are readily
More informationExplosion and flame-proof cast iron electric motors
Explosion and flame-proof cast iron electric motors EEx-d, EEx-de, IIB, IIC II, 2G IP55 II, 2G&D IP66 T4, T5, T6 Frame size 56 to 160 3 phases Voltage 230/400 V 50Hz Voltage 265/460V 60Hz Types of mounting
More informationCOMBROIND001_= THREE PHASE SQUIRREL CAGE INDUCTION MOTORS. IE1 motors MAA - BAA Series IE2 motors MAQ - BAQ Series
COMBROIND001_= THREE PHASE SQUIRREL CAGE INDUCTION MOTORS IE1 motors MAA - BAA Series IE2 motors MAQ - BAQ Series 03 07 07 08 12 15 15 16 18 20 SPECIFICATIONS AND STANDARDS IE1 - MAA / BAA Series Technical
More informationIE2 and IE3 THREE PHASE ASYNCHRONOUS ELECTRIC MOTORS PRODUCT CATALOGUE ELK
IE2 and IE3 THREE PHASE ASYNCHRONOUS ELECTRIC MOTORS PRODUCT CATALOGUE ELK 000-0616 PRODUCTION SITE AND PRODUCTION TECHNOLOGY ELK Motor has been founded by major shareholders of Yılmaz Redüktör A.Ş. as
More informationAluminium Frame Motors Improved Efficiency EFF2
Motors Energy Automation Coatings Aluminium Frame Motors Improved Efficiency EFF2 Standard Features: Three-phase, multivoltage, IP55, TEFC : 0.12 up to 11kW Frames: 63 up to 132M Voltage: 220-240/380-415V
More informationLow Voltage General Purpose Motors
Low Voltage General Purpose Motors Making you more competitive ABB s General purpose motor is designed for use in general industry, meeting the demands of standard applications for OEM's. Motors are readily
More informationAC Square Motors. Electric. AMP Series kw HP Nm (at 1500rpm) Catalogue-2017/12 EU
C Square Motors Catalogue-2017/12 EU MP Series 112-355 16-1300 21-1750 HP 102-8280 (at 1500) 1 Electric 2 Table of contents GENERL FORMTION...5 BSIC DESIGN...6 IEC standard....6 Insulation...6 Temperature
More informationELK PRODUCT CATALOGUE. elkmotor.com.tr
ELK 0501-0418 PRODUCT CATALOGUE elkmotor.com.tr THREE PHASE SQUIRREL CAGE ASYNCHRONOUS MOTORS ELK Motor has been founded by major shareholders of Yılmaz Reduktor, as a continuation of the product family.
More informationLow Voltage General Purpose Motors
Low Voltage General Purpose Motors Making you more competitive ABB s General purpose motor is designed for use in general industry, meeting the demands of standard applications for OEM's. Motors are readily
More informationAESV / AESU / AESV-LA Series Squirrel Cage Induction Motor AESV1S / AESU1S / AESV1S-LA (IE1) STANDARD EFFICIENCY
AESV / AESU / AESV-LA Series Squirrel Cage Induction Motor AESV1S / AESU1S / AESV1S-LA (IE1) STANDARD EFFICIENCY AESV2S / AESU2S / AESV2S-LA (IE2) HIGH EFFICIENCY AESV3S / AESU3S / AESV3S-LA (IE3) PREMIUM
More informationM3000 Steel Motors. ABB LV Motors M3000 Range
M3000 Steel Motors ABB LV Motors M3000 Range Making you more Competitive ABB LV Motors knows about customer needs. For over 100 years we have been designing motors for every need and application. With
More informationCE Marking. Number of poles. Core Length. Frame size
269 Electric Motors General Information CHALLENGE series three phase asynchronous AC electric motors, Are totally enclosed fan cooled (IC-411) squirrel caged type, With IP55 enclosure protection, Class
More informationTECHNICAL REQUIREMENTS FOR ELECTRICAL EQUIPMENT
Page 1 (7) TECHNICAL REQUIREMENTS FOR ELECTRICAL EQUIPMENT Title Document Asynchronous electric motors TBE 103 Issue 6 (E) Contents 1 GENERAL... 2 2 DEFINITIONS... 2 3 GENERAL PRODUCT REQUIREMENTS... 3
More informationM O T O R S. T E C Electric Motors Ltd.
M O T O R S T E C Electric Motors Ltd. GENERAL INFORMATION THREE PHASE-TECA/TECC TYPES-IE1/IE SINGLE PHASE-TPC/TCC TYPES BRAKE MOTOR-TECA-BM TYPE THREE PHASE MOTORS ECOL-IE1/IE/IE3 TEC motors are designed
More informationMOUNTING & MAINTENANCE INSTRUCTIONS FOR
9 Pages / Page 1 MOUNTING & MAINTENANCE INSTRUCTIONS FOR THREEPHASE INDUCTION MOTORS - TYPES DM1 / DMA1 / DMA2 TABLE OF CONTENTS page 1 General information 2 2 Delivery 2 3 Mounting 2 4 Coupling 2 4.1.
More informationARAGON MOTO R S. Three Phase Induction Motors
ARAGON MOTO R S Three Phase Induction Motors Introduction PEM series motors are defined as totally enclosed, fancooled, squirrel cage type and noted for their novel design, beautiful modelling, compact
More informationLSES high efficiency three-phase asynchronous motors. General information
Efficiency class IE2 General information Totally enclosed three-phase saving asynchronous motors, series, according to IEC 60034, 60038, 60072 ; 0.75 to 200 kw, frame size 80 to 315 mm. Single speed: 2,4
More informationIndustrial Performance Motors. New Aluminum and Cast Iron Motors. Flexibility
Industrial Performance Motors New Aluminum and Cast Iron Motors Flexibility Low Voltage Industrial Performance Motors Flexibility Industrial performance motors offer the flexibility needed by most of our
More informationDrive IT Low Voltage General Purpose Motors
Drive IT Low Voltage General Purpose Motors Making you more competitive ABB s General purpose motors are readily available from central stock locations and distributors throughout the world. While designed
More informationThree Phase Squirrel Cage Induction Motors
Three Phase Squirrel Cage Induction Motors A5 - B5 SERIES 160-500 SIZES LOW AND HIGH VOLTAGE INDUSTRIAL APPLICATIONS ASI.CT.045.0 GB your partner in power technology INDEX Pag. PRODUCT CODE STRUCTURE 2
More informationPLS Open Drip Proof three-phase asynchronous motors. General information
General information Open Drip Proof three-phase asynchronous motors, series PLS, according to IEC 60034, 60066, 60072 power 7,5 kw to 900 kw, frame size 160 to 400 mm, 2, 4, 6 and 8 ; 230/400 V or 400
More informationIEC Low Voltage Induction Motors 460 V 60 Hz. Motors for all applications
IEC Low Voltage Induction Motors 460 V 60 Hz Motors for all applications Making you more competitive ABB has been manufacturing motors for over 100 years. Our products are designed to be reliable, effi
More informationGENERAL SPECIFICATIONS
PRODUCT DATA Visedo DRUM features: Synchronous Reluctance assisted Permanent Magnet (SRPM) technology Extremely compact and robust structure Highest efficiency throughout the operation range on the market
More informationCatalog. Low voltage Industrial performance motors
Catalog Low voltage Industrial performance motors We provide motors and generators, services and expertise to save energy and improve customers processes over the total lifecycle of our products, and beyond.
More informationMetric Efficient Line Cast-iron IEC Motors
Metric Efficient Line Cast-iron IEC Motors SPECIFICATION FOR METRIC EFFICIENT LINE CAST-IRON (MELC) IEC MOTORS IN CHILE-ARGENTINA-BOLIVIA Three Phase, IP55 Cast-iron IE2 Metric Motors @ 40 C Ambient Motor
More informationMounting & Maintenance Instructions OMT1 & OMT2 Motors
Mounting & Maintenance Instructions OMT1 & OMT2 Motors Seite 1 von 10 Inhalt Seite 1 General information 3 2 Delivery 3 3 Mounting 3 4 Coupling 3 4.1 Direct coupling 3 4.2 Indirect coupling 4 4.2.1 Flat
More informationElectric machine, permanent magnet internal
EM-PMI540-T1500 Electric machine, permanent magnet internal FEATURES Synchronous Reluctance assisted Permanent Magnet (SRPM) technology Extremely compact and robust structure Highest efficiency throughout
More informationAC MOTORS. Bangalore, India
AC MOTORS Bangalore, India Established in 1982, Integrated Electric (IEC) manufactures high quality electrical rotating machines and drives in a wide range and variety. Its product basket includes DC Motors
More informationLow Voltage Smoke Venting Motors
Low Voltage Smoke Venting Motors New motor range for smoke venting applications Many solutions for fi re protection require smoke-venting fans to move the smoke gases out into the open air. Dual-purpose
More informationExplosion-Proof Motors Increased Safety
Explosion-Proof Motors Increased Safety II 2G Ex e II T3 - T4 II 2G Ex e II T3 - T4 / II 2D Ex td 21 Txxx C II 2D Ex td 21 Txxx C 0344 Certified to TEX Directive 94/9/EC Product Catalogue DESCRIPTION OF
More information1LG0 Low-voltage Motors
Low-voltage motors up to 315kW Catalog D81.5.1 1LG Low-voltage Motors Answers for industry. 1 Table of Contents Overview 3 Motor standards 5 Mechanical design 6 Electrical design 1 Converter fed application
More informationHLA series Cast aluminium multi-mount
HLA series Cast aluminium multi-mount We convert power into motion to help the world run more efficiently BUSINESS PURPOSE ABOUT US Regal Beloit Corporation is a leading manufacturer of electric motors,
More informationXPA series motors High Specification / Premium High Efficiency
60 Years Proudly manufacturing since 1948 XPA series motors High Specification / Premium High Efficiency Accreditation No. 14396 Solutions, not just products. Specialists in Electric Motors, Geared Motors
More informationElectric machine, permanent magnet internal
Electric machine, permanent magnet internal FEATURES Synchronous Reluctance assisted Permanent Magnet (SRPM) technology Extremely compact and robust structure Highest efficiency throughout the operation
More informationStarting of Induction Motors
1- Star Delta Starter The method achieved low starting current by first connecting the stator winding in star configuration, and then after the motor reaches a certain speed, throw switch changes the winding
More informationSevere Duty is Standard with WEG W22 motors
W22 Severe Duty TEFC Severe Duty is Standard with WEG W22 motors W22 Severe Duty TEFC Severe Duty High performance with maximum energy efficiency is the goal of the new WEG electric motor. High efficiency
More informationHIGH EFFICIENCY INDUCTION MOTORS COMBROHEF001_=
COMBROHEF001_= HIGH EFFICIENCY INDUCTION MOTORS High efficiency induction motors General specifications Rated outputs and efficiency values are in accordance with IEC 60034-30-1 all parameters are measured
More informationW22 Brake Motor Three-phase Electric Motor
Motors Automation Energy Transmission & Distribution Coatings W22 Brake Motor Three-phase Electric Motor African Market -- Visual index Main motor parts 1 Sealing system 8 Fan 2 Endshields 9 Bridge rectifier
More informationLSES high efficiency three-phase asynchronous motors General information
General information Efficiency class IE2 Totally enclosed three-phase powersaving asynchronous motors, LSES series, according to IEC 60034, 60038, 60072 ; power 0.75 to 200 kw, frame size 80 to 315 mm.
More informationCatalog June 2016 Low voltage General performance motors
Catalog June 2016 Low voltage General performance motors With expertise, and a comprehensive portfolio of products and life-cycle services, we help value-minded industrial customers improve their energy
More informationOur brand names are known as both Cantoni Motor (CC045A) and Elektrim (CC025A).
This catalogue covers general purpose industrial motors, And crusher duty motors produced by antoni Group. Our brand names are known as both antoni Motor (045A) and Elektrim (025A). antoni Group manufactures
More informationTYPE 2 poles 4 poles 6 poles 8 poles 2 / 4 poles 4 / 8 poles 2 / 8 poles 4 / 16 poles
BAH-BAHS series Overwiew MGM Electric Motors was established in 1950 as a brake motors manufacturer. MGM is today a world leading manufacturer of this line of products. MGM brake motors are designed and
More informationCatalog October 2014 Low voltage General performance motors according to EU MEPS
Catalog October 2014 Low voltage General performance motors according to EU MEPS With expertise, and a comprehensive portfolio of products and life-cycle services, we help value-minded industrial customers
More informationThis catalogue also includes cooling medium pumps of the types DKP and EKP.
AUTRIA INTRODUCTION FFD offers a full range of low voltage electric motors, single phase motors as well as three phase squirrel cage induction motors for continuous duty. All motors are manufactured according
More informationCORE VALUES TECHNOLOGIES ESS-ESD PRODUCT CATALOGUE Enjoy the peace of mind ENGINE POWER SUPPLIERS AND EQUIPMENT HEAT
TECHNOLOGIES ENGINE POWER SUPPLIERS AND EQUIPMENT HEAT Enjoy the peace of mind ESS-ESD PRODUCT CATALOGUE CORE VALUES PEACE OF MIND EFFICIENCY FAIRNESS RESPONSIBILITY CUSTOMER ORIENTATION GROWING DEVELOPED
More informationCPLS Asynchronous motors for variable frequency. 95 Nm to 2900 Nm
95 Nm to 2900 Nm Introduction The range of IP23 protection CPLS asynchronous motors was designed for fixed and variable speed applications when there is little space available or (and) there is a wide
More informationTechnical Documentation
Technical Documentation (B)OK 05 EN Drip - Pro Electric Motors type OK and (2.)B(P)OK Drip-Pro 3-Phase Induction Marine Motors Vision We set your ideas in motion. We do not merely manufacture motors, but
More informationCONTENTS 1 GENERAL 2 STANDARDS. 3 TECHNICAL FEATURES 3.1 Basic Design Data 3.2 Standard Accessories 3.3 Tolerances
CONTENTS 1 GENERAL 2 STANDARDS 3 TECHNICAL FEATURES 3.1 Basic Design Data 3.2 Standard Accessories 3.3 Tolerances 4 MOTOR DESIGN 4.1 Stator Casing 4.2 Stator Core with Winding 4.3 Stator Winding and Insulation
More informationKeeping Industry Turning
Keeping Industry Turning W high voltage, high output 0154E issue Specification, standards & introduction Specification W high voltage, high output Standards Specification The W high voltage,high output
More informationBFG range BFGC range BFN range
BFG range BFGC range BFN range LOW AND MEDIUM VOLTAGE MOTORS FOR HAZARDOUS AREAS EEx d EEx de EEx na - Flameproof Motors - Flameproof Motors With Increased Safety Terminal Box - Non Sparking Motors TABLE
More informationDrive IT Low Voltage General Purpose Motors
Drive IT Low Voltage General Purpose Motors Making you more competitive ABB s General purpose motors are readily available from central stock locations and distributors throughout the world. While designed
More informationGeneral Purpose Three Phase Motors TEFC (IP55) High Efficiency. Standard Features
TM WEG W21 Severe Duty motors meet the most demanding severe duty application requirements. These TEFC motors are all cast iron construction, with enclosures rated IP55 to handle wet and dirty environments.
More informationLow Voltage 3-Phase Induction Motors. Range 0.55kW to 500kW TOTALLY ENCLOSED FAN-COOLED CAST IRON FRAME SERIES AUSTRALIA & NEW ZEALAND
Low Voltage 3-Phase Induction Motors Range 0.55kW to 500kW TOTALLY ENCLOSED FAN-COOLED CAST IRON SERIES General Information MONARCH GX - Three Phase Induction Motors are a range of high quality, Totally
More informationMAX-VH. Vertical Hollow Shaft Motors
MAX-VH Vertical Hollow Shaft Motors Specifications OTHER PERFORMANCE CONSTRUCTION APPLICATION RATING Item Type Of Motors Design Standards Voltages Frequency Output Range RPM (SYN.) Time Duty Frame Size
More informationDrive IT Low Voltage General Purpose Motors
Drive IT Low Voltage General Purpose Motors Making you more competitive ABB s General purpose motors are readily available from central stock locations and distributors throughout the world. While designed
More informationCATALOG JUNE Low voltage General performance motors
CATALOG JUNE 2018 Low voltage General performance motors With expertise, and a comprehensive portfolio of products and life-cycle services, we help value-minded industrial customers improve their energy
More information