#97-T-20A: MIL (Service Engine Soon Telltale Lamp) On and EGR DTCs P0401, P0404, P0405, P1404 and/or P1406 in PCM Memory - (Jan 6, 2003)

Size: px

Start display at page:

Download "#97-T-20A: MIL (Service Engine Soon Telltale Lamp) On and EGR DTCs P0401, P0404, P0405, P1404 and/or P1406 in PCM Memory - (Jan 6, 2003)"

Archibald Dorsey
5 years ago
Views:

1 #97-T-20A: MIL (Service Engine Soon Telltale Lamp) On and EGR DTCs P0401, P0404, P0405, P1404 and/or P1406 in PCM Memory - (Jan 6, 2003) Subject: Malfunction Indicator Lamp (SERVICE ENGINE SOON Telltale Lamp) On and EGR DTCs P0401, P0404, P0405, P1404 and/or P1406 in PCM Memory (Updated diagnosis and Install Service PCM Calibration) This bulletin is being revised with update diagnostic and repair information for EGR system, bulletin 97-T-20 should be discarded. Models: Saturns Condition The malfunction indicator lamp (MIL) (SERVICE ENGINE SOON telltale lamp) may be On with diagnostic trouble codes (DTCs) P0401, P0404, P0405, P1404 and/or P1406 stored in PCM malfunction history. Cause DTCs P1404 and P1406 may be caused by diagnostic trouble code sensitivity to debris. This debris intermittently prevents the exhaust gas recirculation (EGR) pintle from fully seating. The diagnostic information for DTCs P0401, P0404 and P0405 has been updated to include additional failure modes of the EGR system. Important: The diagnostic logic and operational logic for several DTCs were modified with the calibrations identified in the "Controller/PCM Part Number (End Model)" table. Referring to the service manual could result in mis-diagnosis and unnecessary replacement of parts. Correction To diagnose these conditions, refer to the diagnostic charts in this bulletin. Procedure Connect the Scan tool or the Service Stall System (SSS) to the vehicle and turn the ignition On. The TECH - 2 displays the "Controller Part Number" parameter within the "Vehicle System Information" table. The portable diagnostic tool (PDT) and SSS displays the "PCM Part #" parameter within the "Vehicle ID" table. If the Controller/PCM part number matches one of the numbers listed below, proceed to the diagnostics outlined in this bulletin. If the Controller/PCM part number does not match one of the numbers listed below, the after completing the diagnostics outlined in this bulletin, reprogram the PCM. Reprogram the PCM according to the "Controller/PCM Part Number (End Model)" table listed

2 below. (Refer to "EEPROM Reprogramming" in the "Service Stall System User Guide.") Important: Version 41.0 or greater service stall system (SSS) software is required for this flash process. Verify the SSS is version 41.0 or greater. If SSS version 41.0 or greater is not available, call Saturn Customer Support Center at SATURN ( ), prompt 3. In Canada, call for English, or for French. Emissions Engine Transaxle California Federal Taiwan/Canada Japan Base (L24) Perf (LL0) Base (L24) Perf (LL0) Base (L24) Perf (LL0) Perf (LL0) CONTROLLER/PCM PART NUMBER (END MODEL) Model Year 1996 Model Year 1996 (Vehicle Equipped w/1997 Service PCM) Model Year 1997 Automatic Manual Automatic Manual Automatic Manual Automatic Manual Automatic Automatic Manual Automatic N/A N/A Manual N/A N/A Important: It will be necessary to perform the crankshaft learning procedure. (Refer to Technical Information Bulletin 96-T-39, and perform the Crankshaft Learning Procedure contained in the bulletin.) Claim Information To receive credit for this repair during the warranty coverage period, submit a claim through the Saturn Dealer System as follows: Case Type Description Labor Operation Code Time VW Install Service PCM Calibration T hrs

3 EGR - INSUFFICIENT FLOW DETECTED The linear EGR system consists of a linear EGR valve, the PCM and its associated writing. The PCM directly controls the ground for the EGR valve when certain conditions have been met. Voltage is supplied by the UHJB to the EGR valve when the ignition is turned On. When the PCM grounds the valve, a diagnostic feedback signal can determine if the valve had actually moved. Since the correct feedback voltage is possible, but the passage has restricted flow, P0401 was implemented. DTC PARAMETERS EGR flow restrictions are diagnosed during a deceleration. The EGR valve is commanded closed during a normal deceleration. To run the P0401 test the valve is opened during deceleration and a change in MAP is expected. If the change in MAP is below a threshold it indicates flow restricted. DTC P0401 will set if a calculated value compared to an engine speed vs barometric pressure determines there is a restriction in EGR flow when: Engine speed is between rpm. VSS is greater than 48 km/h (30 mph). Throttle is closed. Engine coolant temperature is greater than 70 C (150 F). Vehicle is in top gear. No EGR pintle, TP Sensor, MAP, VSS, LAT, ECT or IAC DTCs have been set. Important: The EGR flow insufficient test is checked once per ignition cycle during deceleration. DIAGNOSTIC AIDS The Scan tool can read the number of deceleration tests that have been performed since the

4 DTCs were cleared. The Scan tool also displays the EGR decel average value as well as the FAIL threshold when the DTC is set. The average must be greater than the threshold to set P0401. Carbon buildup around the EGR pintle valve bore opening may restrict exhaust gas flow. Buildup of carbon in the EGR passages will result in P0401. Diagnose the other DTCs listed under parameters, especially a MAP sensor DTC before diagnosing P0401.

6 EGR - PINTLE POSITION ERROR The linear EGR system consists of a linear EGR valve, the PCM and its associated wiring. The EGR valve solenoid is controlled directly by the PCM when certain conditions have been met. The PCM contains a diode feedback circuit which dissipates energy when the valve is cycled Off. When the PCM grounds the valve, the diagnostic feedback signal can determine if the valve had actually moved. DTC P0404 has been defined to monitor the under different valve operating conditions. DTC PARAMETERS If commanded position is greater than 80%, actual position must be within 26 counts (10% [0.5 volts]) of commanded. If commanded position is less than 80%, actual position must be within 60 counts (24% [1.1 volts]) of commanded. Two consecutive ignition cycles while the diagnostic runs with an active fault. DTC P0404 will set if either condition exists for greater than 10 seconds. When either one of these tests have failed, a DTC will set and EGR will be disabled for that ignition cycle. The malfunction history record will indicate which one of these tests has failed to aid in diagnostics. Important: The EGR position error is continuously checked when the EGR is commanded On. Important: The EGR valve may operate at any engine coolant temperature regardless of loop mode. Important: When this DTC sets, some EGR functions will be disabled for the duration of that ignition cycle. When repairs are complete, codes must be cleared and ignition keyed off for at least 10 seconds to allow proper operation. DIAGNOSTIC AIDS

7 Check the backed out or damaged terminals. Check the tightness of the female terminal grip with a spare male terminal. Check for B+ voltage at the E terminal on the EGR valve when the ignition is On. Check EGR 10-amp fuse in the UHJB before diagnosing this DTC. Carbon buildup around the pintle valve may restrict pintle movement. An open in the PCM diode feedback circuit will result in unstable valve operation resulting in vehicle surge. Due to moisture associated with the exhaust system, the EGR valve may freeze and stick in extreme cold ambient conditions.

9 EGR - VOLTAGE OUT OF RANGE - OPEN/SHORT The linear EGR system consists of a linear EGR valve, the PCM and its associated wiring. The EGR valve solenoid is controlled directly by the PCM when certain conditions have been met. The PCM contains a diode feedback circuit which dissipates energy when the valve is cycled Off. When the PCM grounds the valve, a diagnostic feedback signal can determine if the valve had actually moved. DTC P0405 has been defined to monitor the feedback signal. This diagnostic will determine if the position feedback signal properly falls within the correct range under different valve operating conditions. DTC PARAMETERS DTC P0405 will set if the following condition are met: IGN voltage is above 11.0 volts Voltage is less than 0.20 volts Condition present for greater than five seconds. When this DTC fails, EGR will be disable for the entire ignition cycle. The malfunction history record aid in diagnosis. Important: The EGR valve may operate at any engine coolant temperature regardless of loop mode. TEST DESCRIPTION 1. Normal closed valve position feedback voltage should be greater than 0.20 volts at all times. 2. A voltage of less than 0.2 volts indicates a problem with the position feedback circuit. DIAGNOSTIC AIDS Check for backed out or damaged electrical terminals.

10 Check the tightness of the female terminal grip with a spare male terminal. A short to ground in the 5-volt reference will set both a P1635 and a P0405. If both are set, diagnose P1635 first. An open in the 5-volt reference will set only the P0405. An open in the PCM diode feedback circuit will result in unstable valve operation resulting in vehicle surge.

12 EGR - CLOSED POSITION ERROR The linear EGR system consists of a linear EGR valve, the PCM and its associated wiring. The EGR valve solenoid is controlled directly by the PCM when certain conditions have been met. The PCM contains a diode feedback circuit which dissipates energy when the valve is cycled Off. When the PCM commands the EGR valve closed, a closed valve position value is learned. If the PCM commands the valve closed and the actual feedback value does not match the learned value, DTC P01404 will set. DTC PARAMETERS DTC P1404 will set when the actual closed value does not match learned closed within 20 seconds if: RPM is below 5000 and the actual vs learned is greater than 0.2 volts, or RPM is above 5000 and the actual vs learned is greater than 0.4 volts. Important: If DTCs P0404 or P0405 are also set, begin diagnosis with these DTCs first. Do not clear codes until diagnosis is completed. Important: When the PCM recognizes that the parameters for setting P1404 have been set, the diagnostic software waits until the EGR cycles open 50% or greater four times and then retests. If after the four cycles the actual vs learned is not within the parameters, the DTC will be stored and the MIL (SERVICE ENGINE SOON) will be commanded on. Important: When this DTC sets, functions will be disabled. When repairs are complete, codes must be cleared and ignition keyed off for at least 10 seconds to allow proper operation. DIAGNOSTIC AIDS Check for backed out or damaged terminals.

13 Check for a stuck open EGR pintle. Inspect EGR pintle valve bore for carbon or debris and remove. Verify that the pintle moves freely and the return spring forces the pintle closed. An open in circuit 452 will result in P1404. A short to ground in circuit 697 will result in a severe rough idle and driveability complaint and set a P1404. Check for backed out, damaged, poor terminal tightness or an intermittent open in circuits 416 or 1456.

14 GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

DTC P1404 Exhaust Gas Recirculation (EGR) Closed Position Performance

Page 1 of 5 DTC P1404 Exhaust Gas Recirculation (EGR) Closed Position Performance Circuit Description The PCM monirs the EGR valve pintle position input ensure that the valve responds properly commands