SPECIALTY AND HARSH ENVIRONMENT FIBER OPTIC CABLE. Downhole Subsea Transit Mining Military

Transcription

1 SPECIALTY AND HARSH ENVIRONMENT FIBER OPTIC CABLE Downhole Subsea Transit Mining Military

2 Founded in 1984, AFL is an international manufacturer providing end-to-end solutions to the energy, service provider, enterprise and industrial markets as well as several emerging markets. AFL s products are in use in over 130 countries and include fiber optic cable and hardware, transmission and substation accessories, outside plant equipment, connectivity, test and inspection equipment, fusion splicers and training. AFL also offers a wide variety of services supporting data center, enterprise, wireless and outside plant applications. AFL is dedicated to bringing our customers a quality product as well as delivering superior value.

3 Specialty & Harsh Environment Fiber Optic Cable Table of Contents Downhole and Sensing Traditional Downhole Cable...3 Hybrid Downhole Cable...4 StrataJac Downhole Cable Encapsulation...5 Low Profile Downhole Cable...6 Armored Stainless Steel Tubes...7 Stainless Steel Fiber Optic Tubes...8 Fiber Rod...9 MiniBend Fiber Optic Component...10 Verrillon Harsh Environment Fibers...11 Verrillon VHM5000 Series Fibers...13 Verrillon VHM2000 Series Fibers...16 Verrillon VHS500 Series Fibers...19 Verrillon VHS100 Series Fibers...21 Verrillon VPM400 Series Fibers...24 Subsea Fiber Optic Component for Umbilical Cable...25 Harsh Environment/Transit Listed Gel-Free, LSZH, Loose Tube Cable (LL Series)...26 Gel-Free Extreme Low Temp LSZH Double Jacket I/O Loose Tube (LA Series Gel-Free)...28 XLPO LSZH Gel Free I/O Loose Tube (LX Series)...30 Mining and Military Tactical Tight Buffered Cable...32 Tactical Breakout Cable...34 Tactical Copper/Fiber Composite Cable...36 Ruggedized Indoor/Outdoor Breakout Cable...37 Braided Armored Tactical Tight Buffered Cable...39 Braided Armored Tactical Breakout Cable...40 Aluminum Interlock Loose Tube Cable...41 High Strength Steel Wire (HSSW) Armored Fiber Optic Cable...42 Fusion Splicing Systems Fusion Splicers Fujikura 22S Fusion Splicer...43 Fujikura 70S+ Fusion Splicer...45 FSM-100M and FSM-100P Fusion Splicers...47 Recoaters FSR-02 Fiber Recoater...49 Cleavers CT-30 Fiber Cleaver...50 CT-100 Fiber Cleaver...51 PowerCleave...52 Splicing Accessories USC-03 Ultrasonic Cleaner...53 AFL PowerStrip...54 PCS-100 Polyimide Coating Stripper...55 Splice Protection Sleeves...56 Fiber Management LG-55 Sealed Fiber Optic Splice Closure...58 LightLink 500 Optical Splicing and Distribution Enclosure...59 LightLink Optical Entrance Enclosures...60 LightLink Fiber Optic Splice Trays...63 Test and Inspection Equipment M310 Enterprise OTDR...71 M710 Multifunction OTDR or (800)

4 Specialty & Harsh Environment Fiber Optic Cable or (800)

5 Specialty Fiber Optic Cable Traditional Downhole Cable Traditional Downhole cable from AFL is designed to perform in the well and withstand elevated temperatures, high pressure and corrosive environments. The cable is customized to the customer s specifications in order to maximize performance at the best possible price. AFL s Traditional Downhole cable is targeted to < 150 C offshore and land-based wells where ruggedness is essential. Features Customized to customer specifications Up to 150 C Up to 20,000 psi operating pressure Loose tube design Hydrogen scavenging gel Cable Components Outer Stainless Steel Tube Polyprolylene Inner Jacket Inner Stainless Steel Tube Fiber Hydrogen Scavenging Gel Outer Encapsulation Options and Specifications PARAMETER VALUE Inner Stainless Steel Tube Diameter 0.125" Outer Tube Diameter 0.250" Outer Tube Wall Thickness 0.028", 0.035", 0.049" Outer Tube Material Stainless Steel 316L, Incoloy 825 Fiber Coating Carbon Polyimide, Silicone/PFA, Pure Silica Core and others Gel Types No gel, standard gel, hydrogen scavenging gel Diameter 11 mm x 11 mm square, 11 mm round Polymer Options Polypropylene, PVDF, Nylon, Santoprene Operating Temperature -40 C to 150 C Operating Pressure Limit 0 to 20,000 psi or (800) , AFL, all rights reserved. PP , Revision 2,

6 Specialty Fiber Optic Cable Hybrid Downhole Cable Hybrid Downhole cable from AFL combines copper conductor and optical fibers within the same cable structure for simultaneous deployment. This construction is intended to withstand elevated temperatures, high pressure and corrosive environments. The cable may be customized to the customer s specifications in order to balance performance capability with cost considerations. This design is targeted toward well applications than have operating temperatures 150 C. Features Up to 150 C Incorporates insulated 18AWG copper conductor Loose tube design for optical fibers Hydrogen scavenging gel Customized to customer specifications Cable Components SS Tube, Optical Fibers and Gel 18AWG Insulated Conductor Belting Layer ¼" x 0.035" WT Outer Tube 11 mm x 11 mm Square Outer Encapsulation Options and Specifications PARAMETER VALUE Inner Stainless Steel Tube Diameter 0.071" Copper Conductors 1 x 18 AWG Outer Tube Diameter 0.250" Outer Tube Wall Thickness 0.035" Outer Tube Material Stainless Steel 316L, Incoloy 825 Fiber Types Single-mode, Multimode Gel Types Hydrogen scavenging gel Encapsulation Options None, 11 mm x 11 mm Square, 11 mm Round Polymer Types Polypropylene, PVDF, Nylon, Santoprene Operating Temperature -40 C to 150 C Operating Pressure Limit 0 to 20,000 psi or (800) , AFL, all rights reserved. PP , Revision 1,

7 Specialty Fiber Optic Cable Cables installed in oil and gas wells are exposed to severe mechanical and chemical conditions. Cable damage during run-in and subsequent completion processes such as hydraulic fracturing can lead to premature cable failures. StrataJac is the first cable encapsulation designed exclusively to protect downhole cables by resisting the extreme impact energies and abrasion encountered during run-in, and high pressure, high velocity frac jobs. Abrasion testing has demonstrated a three-fold increase in the amount of time required to breach StrataJac when compared to other commercially available encapsulations. Furthermore, cable impact strength is significantly enhanced when encapsulated with StrataJac. These combined properties make StrataJac ideal for preserving and extending the life of fiber optic cables, TEC cables and chemical injection lines used in critical downhole applications. Features Highly Abrasion and Impact Resistant Suitable for use in severe chemical environments containing H 2 S, CO 2, Methane, Oil, Diesel, Gasoline, Toluene and other organic solvents Wide operating temperature range from -40 C to 150 C Easy to strip using commercially available encapsulation strippers Physical Properties DIAMETER (MM) WEIGHT (KG/KM) PROFILE Round Round or (800) , AFL, all rights reserved. PP , Revision 1,

8 Specialty Fiber Optic Cable Low Profile Downhole Cable AFL s unique offering for shallow, land-based wells provides the best combination of ruggedness and size for the price. AFL will customize the design to meet the customer s needs in order to maximise their return on investment. Cable Components Outer Tube Inner Tube Fiber Hydrogen Scavenging Gel Features Small diameter Low weight Redundant hermetic seal Encapsulation options Lower cost Patent pending Inside Tube Options and Specifications VALUE PARAMETER DOUBLE TUBE TRIPLE TUBE Outer Tube Diameter Tube Wall Thickness Tube Material Stainless Steel 316L, Incoloy 825 Fiber coating Carbon Polyimide, Silicone/PFA, Pure Silica Core and others Gel types No gel, high temperature gel, hydrogen scavenging gel Polymer options Polypropylene, PVDF, Nylon, Santoprene STAINLESS STEEL 316L OPTION Weight 21 lbs / 1,000 ft 28 lbs / 1,000 ft Tensile 760 lbs 1,060 lbs Collapse pressure 30,000 psi 44,000 psi Bend radius (dynamic) 12.6" 12.6" INCOLOY 825 OPTION Weight 22 lbs / 1,000 ft 28 lbs / 1,000 ft Tensile 814 lbs 1,134 lbs Collapse pressure 21,000 psi 32,000 psi Bend radius (dynamic) 12.6" 12.6" ENCAPSULATION OPTION Diameter 1/4" Weight Santoprene 15 lbs / 1,000 ft Polypropylene 14 lbs / 1,000 ft PVDF 28 lbs / 1,000 ft Nylon 16 lbs / 1,000 ft or (800) , AFL, all rights reserved. PP , Revision 3,

9 Fiber Optic Cable Armored Stainless Steel Tubes Armored Stainless Steel Cables from AFL are based on our patented tube technology which provides for a hermetic seal. The armor wires provide improved crush and tensile performance while maintaining good flexibility. Armored Stainless Steel Tubes can be used in a variety of applications such as temperature sensing and surface cable. Cable Components Outer Jacket Features Hermetic Stainless Steel Tube High Strength Wire Jacket Options Gel Options Flexible Rugged Options and Specifications Armor Wires Stainless Steel Tube Hydrogen Scavenging Gel Fiber BREAKING STRENGTH (kg) BEND RADIUS (mm) FIBER COUNT TUBE O.D. (mm) FINAL O.D. (mm) WEIGHT (kg/km) Based on 200 kpsi Gips wire, gel filled tube Encapsulation Option PARAMETER Materials Diameter Cable markings VALUE Polypropylene, Nylon, PVDF, Hytrel To customer specifications To customer specifications or (800) , AFL, all rights reserved. PP , Revision 3,

10 Specialty Fiber Optic Cable Stainless Steel Fiber Optic Tubes As the inventor and owner of the technology for placing optical fibers into stainless steel tubes, AFL offers a range of tube sizes and fiber counts for a variety of applications. Each tube is flooded with a thixotropic filling compound and hermetically sealed to protect the enclosed fibers from environmental degradation. This product is sometimes referred to as FIST (Fiber in Steel Tube) or FIMT (Fiber in Metal Tube). Jacket Options AFL can encapsulate any of our stainless steel tubes with any of the following polymers: Hytrel Polypropylene Santoprene Nylon Polyethylene PVDF Cable Components Outer Jacket Fiber Stainless Steel Tube Applications Umbilical Cables Downhole Cables for Oil & Gas Towed Arrays High Temperature Cables Hybrid Cables Sensor Cable OPGW Specifications (without jacketing) OUTSIDE DIAMETER inches (mm) INSIDE DIAMETER inches (mm) WALL THICKNESS inches (mm) OPTION NUMBER MAXIMUM FIBER COUNT (1.17) (0.91) (0.127) (1.32) (1.07) (0.127) (1.40) (1.00) (0.200) (1.65) (1.25) (0.200) (1.80) (1.40) (0.200) (1.88) (1.47) (0.200) (1.98) (1.57) (0.200) (2.00) (1.60) (0.200) (2.33) (1.93) (0.200) (2.38) (1.98) (0.200) (2.40) (2.00) (0.200) (2.49) (2.08) (0.200) (2.69) (2.29) (0.200) (3.00) (2.60) (0.200) (3.20) (2.80) (0.200) (3.40) (3.00) (0.200) (3.60) (3.20) (0.200) (3.80) (3.40) (0.200) (3.96) (3.56) (0.200) (4.00) (3.60) (0.200) (4.20) (3.80) (0.200) Available in Stainless Steel 304, 316 and Incoloy 825. Others sizes and materials available on request. or (800) , AFL, all rights reserved. PP , Revision 3,

11 Fiber Optic Cable Fiber Rod AFL s Fiber Rod takes an optical fiber of the customer s choice and encases it in a glass re-enforced matrix. The diameter of the structure is adjusted to provide the characteristics needed for the specific application. The performance of the optical fiber is retained in this structure providing for a very ruggedized fiber suitable for many harsh applications. Fiber Rod is best suited for high tensile or compressive requirements where the glass structure provides the rigidity to protect the optical fiber from harm. Additionally, AFL s Fiber Rod does not exhibit the typical curvature coming off the payoff reel like that of most cables. This makes deployments in applications such as pipelines and oil wells simpler. Applications such as strain sensing and temperature sensing in a host of environments up to 200 C are ideal for this product. Features/Options Strength Variable as glass matrix diameter can be increased which increases strength Bend Diameter 50x the outer diameter Temperature Performance Standard is 85 C Ruggedized Option Product can be jacketed with various polymers such as PVDF, Hytrel, Polyethylene, Nylon, PVC, Fire Retardant PE, Polyurethane and others Available in lengths of up to 6 kilometers Cable Components Specifications VALUE PARAMETER OD (mm) ID (mm) TOLERANCE (+/-mm) 85 C Version Optical Fiber n/a Coating (Silicone PFA) or (800) , AFL, all rights reserved. PP , Revision 4,

12 Specialty Fiber Optic Cable MiniBend Fiber Optic Component For Downhole Double-ended Systems and Optical Connectivity The MiniBend miniature fiber optic component employs a revolutionary technology that will change the way you plan and engineer the fiber management in your oil or gas well. This patented technology allows for a single strand of multimode or single-mode fiber to be formed at a 180 bend with a 1 mm fiber bend diameter, saving valuable real estate. Features Elegant, low profile solution for achieving downhole fiber optic double-ended system Provides low-loss sub-millimeter bends for miniaturizing fiber components and circuits No stress with the small bend radii Bi-directional Mechanically and environmentally robust Small and protective package Applications Downhole fiber optic turnaround Fiber management systems Modulators, splitters, circulators, connectors and polarizers Circuit boards and back planes Compact test instrumentation and sensors Dimensions Specifications PARAMETER VALUE Item Number DNS-1574 DNS-1575 DNS-1885 DNS-1890 Fiber Coating Type 50 µm multimode carbon mid-temperature acrylate 50 µm multimode carbon/polyimide single-mode carbon mid-temperature acrylate single-mode carbon/polyimide Operation Wavelength Range 900 to 1340 nm, 1430 to 1600 nm 1280 to 1340 nm, 1430 to 1600 nm Insertion Loss < 0.2 db at 1310 nm of wavelength at room temperature < 0.3 db at 1550 nm of wavelength at room temperature Operating Temperature 0 to 150 C 0 to 200 C 0 to 150 C 0 to 200 C Storage Temperature -60 to 85 C Body Size Outside Diameter = 2.2 mm +/-0.1, Length = 15 mm +/-0.3 Fiber Tail Length > 0.5 m Straight Pull 500 g or (800) , AFL, all rights reserved. PP , Revision 3,

13 Specialty Fiber Optic Cable Harsh Environment Fibers Verrillon Harsh Environment Fibers from AFL are available in a number of designs. Starting with fiber design, we offer both single-mode and multimode optical fibers having coatings and coating combinations, including Polyimide, Silicone-PFA, Silicone-MTA, MTA and Carbon, which can be applied in conjunction with any of these outer coatings. Typically, these fibers are used in downhole data logging, distributed sensing and imaging applications. Verrillon coated fibers provide exceptionally high levels of hermeticity compared to commercial fibers. We provide extensive data that demonstrates the performance of our fiber. In addition, we provide one-stop shopping for customers requiring multi-count cabled hermetic fibers, if required, in metal jacketing tubes. Consistent with our founding principles, we specialize in application optimized fibers, providing our customers unmatched flexibility in the their system design and performance. Features Wide range of protective coatings available, depending on application requirements Suitable for use in high pressure, high temperature and corrosive environments Carbon fiber provides exceptional resistance to H2 and moisture ingression Predicted lifetime for hermetic fiber under typical operating conditions that exceed most requirements Extensive test and measurement data for optical fiber performance under "harsh conditions" provided with fiber or (800) , AFL, all rights reserved. PP , Revision 0,

14 Specialty Fiber Optic Cable Harsh Environment Fibers Verrillon offers the broadest range of specialty fibers for oil and gas sensors of all types: Distributed Temperature Sensors DTS Distributed Pressure Sensors DPS Distributed Strain Sensors DSS Distributed Acoustic Sensors DAS Ocean Bottom Seismic - OBS Verrillon Optical Fiber Selection Matrix MAXIMUM TEMPERATURE CONDITIONS SINGLE-MODE MULTIMODE 85ºC Hydrogen Present VHS100-CA VHM2000-CA 150ºC No Hydrogen VHS100-MTDA VHS100-SMTA VHM2000-MTDA VHM2000-SMTA Hydrogen Present VHS100-CMTDA VHS100-CSMTA VHM2000-CMTDA VHM2000-CSMTA 200ºC All Conditions VHS500-CSPFA VHS500-P VHS500-CP VHM3000-CSPFA VHM3000-P VHM3000-CP 300ºC All Conditions VHS500-P VHS500-CP VHM3000-P VHM5000-P VHM3000-CP VHM5000-CP or (800) , AFL, all rights reserved. PP , Revision 0,

15 Specialty Optical Fiber VHM5000 Series Fibers Verrillon Harsh Environment Fibers from AFL are available in a number of designs. The VHM5000 Series is a multimode graded-index optical fiber available with coatings and coating combinations, including Polyimide, high temperature acrylates, Silicone-PFA and hermetic Carbon. Typically, these fibers are used in down-hole data logging, distributed sensing and imaging applications where the temperature and hydrogen partial pressures are extreme. Verrillon carbon-coated optical fibers provide exceptionally high levels of hermeticity compared to commercial fibers. We provide extensive data that demonstrates the performance of our fiber. In addition, we provide one-stop shopping for customers requiring multi-count cabled hermetic fibers, if required, in metal jacketing tubes. Consistent with our founding principles, we specialize in application optimized fibers, providing our customers unmatched flexibility in the their system design and performance. Specifications Features Best glass resistance to hydrogen at high temperatures and pressures in the entire industry Wide range of protective coatings available, depending on application requirements Suitable for use in high pressure, high temperature and corrosive environments Carbon coating provides exceptional resistance to H 2 and moisture ingression Predicted lifetime for hermetic fiber under typical operating conditions exceeds most requirements Extensive test and measurement data for optical fiber performance under "harsh conditions" provided with fiber PART NO. MMF-50-4-P Description 50/125/155 μm Polyimide coated, Graded Index, Multimode Fiber PARAMETER VALUE Material Coating Polyimide Geometry Core Diameter (μm) 50 ± 2.5 Clad Diameter (μm) 125 ± 2 Core Non-Circularity (%) < 5 Clad Non-Circularity (%) < 1 Core/Clad Offset (μm) < 1.5 Coating Diameter (μm) 155 ± 5 Polyimide Coating Concentricity 1 > 80 Optical NA (nominal) 0.20 Attenuation 850 nm 1300 nm (db/km) < 3.0 < nm 1300 nm (MHz-km) > 300 > 300 Mechanical Proof Test (kpsi) 100 Operating Temperature ( C) -65 to Measured as (Min. Wall/Max. Wall) x Measured on loose coil or (800) , (508) , AFL, all rights reserved. PP , Revision 2,

16 Specialty Optical Fiber VHM5000 Series Fibers Specifications PART NO. MMF-50-4-CP MMF-50-4-CP MMF-50-4-CP Description 50/125/155 μm Carbon/Polyimide 50/125/155 μm Carbon/Polyimide 50/125/155 μm Carbon/Polyimide coated, Graded Index Multimode Fiber, Graded Index, Multimode Fiber, coated, Graded Index Multimode Fiber 200 kpsi 150 kpsi PARAMETER VALUE Material Hermetic Carbon Carbon Carbon Coating Polyimide Polyimide Polyimide Geometry Core Diameter (μm) 50 ± ± ± 2.5 Clad Diameter (μm) 125 ± ± ± 2 Core Non-Circularity (%) < 5 < 5 < 5 Clad Non-Circularity (%) < 1 < 1 < 1 Core/Clad Offset (μm) < 1.5 < 1.5 < 1.5 Coating Diameter (μm) 155 ± ± ± 5 Polyimide Coating Concentricity 1 > 80 > 80 > 80 Optical NA (nominal) Attenuation 850 nm 1300 nm (db/km) 850 nm 1300 nm (MHz-km) < 3.0 < 1.2 > 300 > 300 < 3.0 < 1.2 > 300 > 300 < 3.0 < 1.2 > 300 > 300 Mechanical Proof Test (kpsi) Operating Temperature ( C) -65 to to to Measured as (Min. Wall/Max. Wall) x Measured on loose coil or (800) , (508) , AFL, all rights reserved. PP , Revision 2,

17 Specialty Optical Fiber VHM5000 Series Fibers Specifications PART NO. MMF-50-4-CSPFA MMF-50-4-CSPFA MMF-50-4-CSPFA MMF-50-4-CSPFA Description 50/125/750 μm Carbon/ Silicone/PFA, Graded Index, Multimode Fiber, 150 kpsi 50/125/400 μm Carbon/ Silicone/PFA coated, Graded Index, Multimode Fiber 50/125/250 μm Carbon/ Silicone/PFA coated, Graded Index, Multimode Fiber 50/125/250 μm Carbon/ Silicone/PFA coated, Graded Index, Multimode Fiber, 150 kpsi PARAMETER VALUE Material Hermetic Carbon Carbon Carbon Carbon Primary Coating Silicone Silicone Silicone Silicone Secondary Coating PFA PFA PFA PFA Geometry Core Diameter (μm) 50 ± ± ± ± 2.5 Clad Diameter (μm) 125 ± ± ± ± 2 Core Non-Circularity (%) Clad Non-Circularity (%) Core/Clad Offset (μm) Combined Coating Diameter (μm) 750 ± ± ± ± 50 Optical NA (nominal) Attenuation 850 nm 1300 nm (db/km) 850 nm 1300 nm (MHz-km) Mechanical < 3.0 < 1.0 > 300 > 300 < 3.0 < 1.2 > 300 > 300 Proof Test (kpsi) > 150 > 100 > 100 > 150 Operating Temperature ( C) -40 to to to to Measured on loose coil < 3.0 < 1.2 > 300 > 300 < 3.0 < 1.2 > 300 > or (800) , (508) , AFL, all rights reserved. PP , Revision 2,

18 Specialty Optical Fiber VHM2000 Series Fibers Verrillon Harsh Environment Fibers from AFL are available in a number of designs. Starting with fiber design, we offer both single-mode and multimode optical fibers having coatings and coating combinations, including Polyimide, Silicone-PFA, Silicone-MTA, MTA and Carbon, which can be applied in conjunction with any of these outer coatings. Typically, these fibers are used in downhole data logging, distributed sensing and imaging applications. Verrillon carbon-coated optical fibers provide exceptionally high levels of hermeticity compared to commercial fibers. We provide extensive data that demonstrates the performance of our fiber. In addition, we provide one-stop shopping for customers requiring multi-count cabled hermetic fibers, if required, in metal jacketing tubes. Consistent with our founding principles, we specialize in application optimized fibers, providing our customers unmatched flexibility in the their system design and performance. Features 50/125 µm graded index multimode fiber, enhanced resistance level to H 2 ingression Suitable for use in low/mid-temperature, no/low hydrogen environments Carbon coating provides exceptional resistance to H 2 and moisture ingression Wide range of protective coatings available Specifications PART NO. MMF-50-3-CP MMF-50-3-P Description 50/125/155 μm Carbon/Polyimide coated, Graded Index, Multimode Fiber 50/125/155 μm Polyimide coated, Graded Index, Multimode Fiber PARAMETER VALUE Material Hermetic Coating Carbon Coating Polyimide Polyimide Geometry Core Diameter (μm) 50 ± ± 2.5 Clad Diameter (μm) 125 ± ± 2 Core Non-Circularity (%) < 5 < 5 Clad Non-Circularity (%) < 1 < 1 Core/Clad Offset (μm) < 1.5 < 1.5 Coating Diameter (μm) 155 ± ± 5 Polyimide Coating Concentricity 1 > 80 > 80 Optical NA (nominal) Attenuation 850 nm 1300 nm (db/km) < 3.0 < 1.2 < 3.0 < nm 1300 nm (MHz-km) > 300 > 300 > 300 > 300 Mechanical Proof Test (kpsi) > 100 > 100 Operating Temperature ( C) -65 to to Measured as (Min. Wall/Max. Wall) x Measured on loose coil or (800) , (508) , AFL, all rights reserved. PP , Revision 0,

19 Specialty Optical Fiber VHM2000 Series Fibers Specifications PART NO. MMF-50-3-MTDA MMF-50-3-CSMTA MMF-50-3-CMTDA MMF-50-3-CMTDA Description 50/125/245 μm Mid-Temp Dual Acrylate coated, Graded Index, Multimode Fiber 50/125/245 μm Carbon/ Si/Mid-Temp Dual Acrylate, Graded Index, Multimode Fiber 50/125/245 μm Carbon/ Mid-Temp Dual Acrylate coated, Graded Index, Multimode Fiber 50/125/245 μm Carbon/ Mid-Temp Dual Acrylate, Graded Index, Multimode Fiber, 200 kpsi PARAMETER VALUE Material Hermetic Coating Carbon Carbon Carbon Primary Coating Mid-Temp Dual Acrylate Silicone Mid-Temp Dual Acrylate Mid-Temp Dual Acrylate Secondary Coating Mid-Temp Dual Acrylate Mid-Temp Dual Acrylate Mid-Temp Dual Acrylate Mid-Temp Dual Acrylate Geometry Core Diameter (μm) 50 ± ± ± ± 2.5 Clad Diameter (μm) 125 ± ± ± ± 2 Core Non-Circularity (%) Clad Non-Circularity (%) Core/Clad Offset (μm) Combined Coating Diameter (μm) 245 ± ± ± ± 5 Optical NA (nominal) nm 1300 nm (db/km) 850 nm 1300 nm (MHz-km) > 300 > > 300 > 300 Mechanical Proof Test (kpsi) > 100 > 100 > 100 > 200 Operating Temperature ( C) -40 to to to to > 300 > > 300 > or (800) , (508) , AFL, all rights reserved. PP , Revision 0,

20 Specialty Optical Fiber VHM2000 Series Fibers Specifications PART NO. MMF-50-3-SPFA MMF-50-3-SPFA MMF-50-3-CSPFA Description 50/125/700 μm Silicone/PFA coated, Graded Index, Multimode Fiber 50/125/250 μm Silicone/PFA coated, Graded Index, Multimode Fiber 50/125/400 μm Carbon/Silicone/PFA coated, Graded Index Multimode Fiber PARAMETER VALUE Material Hermetic Coating Carbon Primary Coating Silicone Silicone Silicone Secondary Coating PFA PFA PFA Geometry Core Diameter (μm) 50 ± ± 3 50 ± 2.5 Clad Diameter (μm) 125 ± ± ± 2 Core Non-Circularity (%) Clad Non-Circularity (%) Core/Clad Offset (μm) Combined Coating Diameter (μm) 700 ± ± ± 50 Optical NA (nominal) Attenuation 850 nm 1300 nm (db/km) nm 1300 nm (MHz-km) > 300 > 300 > 300 > 300 > 300 > 300 Mechanical Proof Test (kpsi) > 100 > 100 > 100 Operating Temperature ( C) -40 to to to Measured on loose coil or (800) , (508) , AFL, all rights reserved. PP , Revision 0,

21 Specialty Optical Fiber VHS500 Series Fibers Verrillon Harsh Environment Fibers from AFL are available in a number of designs. VHS500 is a pure silica core single-mode design available with all Verrillon harsh environment coating combinations, including Polyimide, Silicone-PFA, Silicone-MTA, MTA and Carbon, which can be applied in conjunction with any of these polymeric coatings. Typically, these fibers are used in downhole distributed sensing techniques for temperature, pressure, acoustics and seismic, as well as in data logging and imaging applications. Our carbon-coated optical fibers provide exceptionally high levels of hermeticity compared to commercial fibers. We provide extensive data that demonstrates the performance of our fiber in simulated well conditions. In addition, we provide one-stop shopping for customers requiring single or multi-count cabled hermetic fibers in metal jacketing tubes and polymeric configurations. Consistent with our founding principles, we specialize in application-optimized fibers, providing our customers unmatched flexibility in their system design and performance. Applications Downhole in oil & gas Cabling processes with tight bending requirements Harsh environment applications Tight bend fiber installations Features Optimized for 1550 nm Single Wavelength Operation Pure Silica Core chemistry for improved performance in hydrogen-rich environments Greater than 50x bend loss improvement at 1550 nm over standard SMF MFD compatible with standard SMF for ease of splicing and minimal splice loss Available with all Verrillon harsh environment coatings Specifications PART NO. SMF-60-CP SMF-60-P Description 125/155 μm Carbon/Polyimide coated Single-mode fiber, 0.12 NA, 100 kpsi, 1550 nm Operating Wavelength 125/155 μm Polyimide coated Single-mode fiber, 0.12 NA, 100 kpsi, 1550 nm Operating Wavelength PARAMETER VALUE Material Hermetic Coating Carbon Coating Polyimide Polyimide Geometry Clad Diameter (μm) 125 ± ± 2 Clad Non-Circularity (%) < 3 < 3 Core/Clad Offset (μm) < 1.5 < 1.5 Coating Diameter (μm) 155 ± ± 5 Polyimide Coating Concentricity 1 (%) Optical NA (nominal) Attenuation 1550 nm (db/km) < 0.8 < 0.8 Cutoff Wavelength (nm) < 1530 < 1530 Mode Field Diameter 1550 nm (db/km) 10.0 ± ± 0.7 Mechanical Proof Test (kpsi) > 100 > 100 Operating Temperature ( C) -65 to to (Min. Wall/Max. Wall) x Measured on loose coil 3 Petermann II Definition or (800) , (508) , AFL, all rights reserved. PP , Revision 2,

22 Specialty Optical Fiber VHS500 Series Fibers Specifications PART NO. SMF-60-CSPFA SMF-60-CSPFA Description 125/700 μm Carbon/Silicone/PFA coated Single-mode fiber, 125/250 μm Carbon/Silicone/PFA coated Single-mode fiber, 0.12 NA, 100 kpsi, 1550 nm Operating Wavelength 0.12 NA, 150 kpsi, 1550 nm Operating Wavelength PARAMETER VALUE Material Hermetic Coating Carbon Carbon Primary Coating Silicone Silicone Secondary Coating PFA PFA Geometry Clad Diameter (μm) 125 ± ± 2 Core/Clad Offset (μm) < 1.5 < 1.5 Combined Coating Diameter (μm) 700 ± ± 50 Optical NA (nominal) nm (db/km) < 0.8 < 0.8 Cutoff Wavelength (nm) < 1530 < 1530 Mode Field Diameter 1550 nm (db/km) 10.0 ± ± 0.7 Mechanical Proof Test (kpsi) > 100 > 150 Operating Temperature ( C) -40 to to Petermann II Definition Specifications PART NO. Description PARAMETER Material Hermetic Coating Coating Geometry Clad Diameter (μm) 125 ± 2 Core/Clad Offset (μm) < 1.5 Coating Diameter (μm) 245 ± 15 Optical NA (nominal) nm (db/km) < 0.8 Cutoff Wavelength (nm) < 1530 Mode Field Diameter 1550 nm (db/km) 10.0 ± 0.7 Mechanical Proof Test (kpsi) > 100 Operating Temperature ( C) -40 to Petermann II Definition SMF-60-CMTDA /245 μm Carbon Mid-Temp Dual Acrylate, Pure Silica Core, Single-mode fiber, 0.12 NA, 100 kpsi, 1550 nm Operating Wavelength VALUE Carbon Mid-Temp Dual Acrylate or (800) , (508) , AFL, all rights reserved. PP , Revision 2,

23 Specialty Optical Fiber VHS100 Series Fibers Verrillon Harsh Environment Fibers from AFL are available in a number of designs. Starting with fiber design, we offer both single-mode and multimode optical fibers having coatings and coating combinations, including Polyimide, Silicone-PFA and Carbon, which can be applied in conjunction with any of these outer coatings. Typically, these fibers are used in down-hole data logging, distributed sensing and imaging applications. Verrillon carbon-coated optical fibers provide exceptionally high levels of hermeticity compared to commercial fibers. We provide extensive data that demonstrates the performance of our fiber. In addition, we provide one-stop shopping for customers requiring multi-count cabled hermetic fibers, if required, in metal jacketing tubes. Consistent with our founding principles, we specialize in application optimized fibers, providing our customers unmatched flexibility in the their system design and performance. Features Equivalent to 'standard' telecom SMF Optimized for 1310/1550 nm Dual Wavelength Operation Carbon coating provides exceptional resistance to H 2 and moisture ingression Wide range of protective coatings available Specifications PART NO. SMF-1-P SMF-1-P SMF-1-CP Description 125/155 µm Polyimide, Single-mode fiber, 125/155 µm Polyimide, Single-mode fiber, 125/155 µm Carbon/Polyimide, 0.12NA, 150 kpsi 0.12NA, 100 kpsi Single-mode fiber, 0.12NA, 100 kpsi PARAMETER VALUE Material Hermetic Coating Carbon Coating Polyimide Polyimide Polyimide Geometry Clad Diameter (μm) 125 ± ± ± 2 Core/Clad Offset (μm) Coating Diameter (μm) 155 ± ± ± 5 Polyimide Coating Concentricity 1 (%) Optical NA (nominal) Attenuation 1310 nm 1550 nm (db/km) Cutoff Wavelength (nm) 1250 ± ± ±50 Mode Field Diameter 1310 nm 1550 nm (μm) 9.2 ± ± ± ± ± ± 0.8 Mechanical Proof Test (kpsi) Operating Temperature ( C) -65 to to to Measured as (Min. Wall/Max. Wall) x Measured on Zero Tension spool 3 Petermann II Definition or (800) , (508) , AFL, all rights reserved. PP , Revision 0,

24 Specialty Optical Fiber VHS100 Series Fibers Specifications PART NO. SMF-1-CMTDA Description 125/245 µm Carbon/ Mid-Temp Dual Acrylate coated, Single-mode fiber 0.12NA, 100 kpsi PARAMETER VALUE Material Hermetic Coating Carbon Coating Mid-Temp Dual Acrylate Geometry Clad Diameter (μm) 125 ± 2 Core/Clad Offset (μm) 0.5 Coating Diameter (μm) 245 ± 15 Optical NA (nominal) 0.12 Attenuation 1310 nm 1550 nm (db/km) Cutoff Wavelength (nm) 1250 ±50 Mode Field Diameter 1310 nm 1550 nm (μm) 9.2 ± ± 0.8 Mechanical Proof Test (kpsi) 100 Operating Temperature ( C) -40 to Measured on loose coil 2 Petermann II Definition Specifications PART NO. SMF-1-MTDA Description 125/245 µm Mid-Temp Dual Acrylate coated, Single-mode fiber, 0.12NA, 100 kpsi PARAMETER VALUE Material Coating Mid-Temp Dual Acrylate Geometry Clad Diameter (μm) 125 ± 2 Core/Clad Offset (μm) 0.5 Coating Diameter (μm) 245 ± 5 Optical NA (nominal) nm 1550 nm (db/km) Cutoff Wavelength (nm) 1250 ± 50 Mode Field Diameter 1310 nm 1550 nm (μm) 9.2 ± ± 0.8 Mechanical Proof Test (kpsi) 100 Operating Temperature ( C) -40 to Petermann II Definition or (800) , (508) , AFL, all rights reserved. PP , Revision 0,

25 Specialty Optical Fiber VHS100 Series Fibers Specifications PART NO. SMF-1-CA SMF-1-CA Description 125/245 μm Carbon/Acrylate coated, Single-mode Fiber, 0.12 NA, 200 kpsi 125/245 μm Carbon/Acrylate coated, Single-mode Fiber, 0.12 NA, 100 kpsi PARAMETER VALUE Material Hermetic Coating Carbon Carbon Coating UV Acrylate UV Acrylate Geometry Clad Diameter (μm) 125 ± ± 2 Core/Clad Offset (μm) Coating Diameter (μm) 245 ± ± 15 Optical NA (nominal) Attenuation 1310 nm 1550 nm (db/km) Cutoff Wavelength (nm) 1250 ± ±50 Mode Field Diameter 1310 nm 1550 nm (μm) 9.2 ± ± ± ± 1.0 Mechanical Proof Test (kpsi) Operating Temperature ( C) -40 to to Measured on loose coil 2 Petermann II Definition or (800) , (508) , AFL, all rights reserved. PP , Revision 0,

26 Specialty Optical Fiber VPM400 Series Fibers Verrillon VPM400 Series is a family of Polarization-Maintaining (PM) Optical Fibers based on the Elliptical-Clad stress technology. These fibers exhibit extremely high birefringence resulting in beat lengths shorter than 2 mm at 1550 nm. VPM400 fibers show significantly lower attenuation at 1550 nm than other PM fiber designs. These fibers are available in various designs and operating wavelengths, as well cladding dimensions including 50, 80 and 125 microns. Features Optimized for 1550 nm Single Wavelength Operation Round core Elliptical Clad designs provide high birefringence allowing the fiber to have an extremely short beat-length, excellent for high-precision gyroscopes Radiation-Resistant Rad-Hard Available in 80 µm clad diameter Applications Fiber optic gyroscopes Fiber lasers Current sensors Specifications PART NO. PMF-9-A-80-1 PMF-12-A-80-1 Description 80 µm Elliptical Clad Polarization maintaining Single-mode Fiber, 1550 nm Operational Wavelength 80 µm Elliptical Clad Polarization maintaining Single-mode Fiber, 1550 nm Operational Wavelength PARAMETER VALUE Material Coating Dual UV Acrylate Acrylate Stress-inducing Design Elliptical Clad Elliptical Clad Geometry Clad Diameter (μm) 80 ± 2 80 ± 2 Core/Clad Concentricity (μm) Coating Diameter (μm) 165 ± ± 10 Optical NA (nominal) Attenuation 1550 nm Mode Field Diameter nm 7.0 ± ± 0.5 Operational Wavelength (nm) Cutoff Wavelength (nm) 1480 < 1520 Beat Length 1550 nm Bend Loss nm 0.05 H-Parameter 5.0 x 10-5 Mechanical Proof Test (kpsi) Operating Temperature ( C) -10 to to Gaussian Definition 2 12 mm diameter mandrel or (800) , (508) , AFL, all rights reserved. PP , Revision 1,

27 Specialty Fiber Optic Cable Fiber Optic Component for Umbilical Cable AFL s Fiber Optic Component for Umbilical Cable is designed for subsea umbilical applications. AFL is the technology owner for hermetic stainless steel tubes which are the key building block for subsea cables. AFL provides customized designs to meet the most stringent requirements. AFL s Fiber Optic Component is suitable for depths of 10,000 feet and beyond. Cable Components Outer Jacket Features Hermetic Stainless Steel Tube High Strength Wire Polyethylene Jacketed Hydrogen scavenging gel Long lengths In-line splice technology Proven technology Long life expectancy Custom Jacket Colors Armor Wires Stainless Steel Tube Inner Jacket Optical Fiber Options and Specifications PARAMETER VALUE Number of Fibers Up to 72 Fiber Single-mode, Multimode, 100 or 200 kpsi proof test Stainless Steel Tube Sizes 2.4 mm to 3.8 mm Stainless Steel Tube Types 304 or 316L Stainless Steel Armor 16 x 1.02 mm (0.040") wires, a range of tensile specifications are available Fiber Colors EIA 598 or customer specification Unit Weight 150 to 300 kg/km Overall Diameter 7 mm to 16 mm Storage Temperature Range -40 to +85 C Operating Temperature Range -40 to +85 C Breaking Load Up to 25 kn (dependant on armor selection) Bend Radius (design dependent) 120 mm to 320 mm Cable Marking To customer specification or (800) , AFL, all rights reserved. PP , Revision 5,

28 Fiber Optic Cable Listed Gel-Free, LSZH, Loose Tube Cable (LL Series) AFL LL-Series Gel-Free fiber optic cables are designed for use in traditional network communication infrastructures deployed in environments requiring the performance of outside plant cabling, while offering the safety of a listed low smoke zero halogen solution. Applications in confined spaces such as tunnels and mine shafts require low smoke zero halogen materials to enhance life safety and minimize damage to sensitive electronic equipment in the event of a fire. Additionally, AFL s product line incorporates the latest dry water-absorption technology within the fiber-containing buffer tubes which results in user-friendly handling of fibers during routing and termination. Temperature Range Operating: -40ºC to +70ºC Storage: -40ºC to +75ºC Installation: -30ºC to +70ºC Crush Resistance Armored: 440 N/cm (250 lbs/in) Non-armored: 220 N/cm (125 lbs/in) Features OFN(C)G-LS allows for use in OSP and inside plant pathways Gel-free buffer tubes reduce fiber prep termination time SZ-stranded cable core for easy mid-span access of fibers UV-stabilized outer jacket for long-term performance in outdoor applications 6 to 288 fibers allow for specific cable choices for multiple applications Specifications OFNG-LS Listed, CSA-FT4, IEEE1202 and UL1685 Meets requirements of NFPA 130 and 502 for use in fixed guideway transit systems and road tunnesls ANSI/ICEA, S , Telcordia and GR-20-CORE Sunlight Resistant Jacket Oil Res II Compliant Jacketing System Zero Halogen Per MIL PRF Rodent-deterrent Jacket Option Available Cable Components LSZH Jacket Optical fiber Gel-free loose buffer tube Optional corrugated steel armoring FRP central member Rip cord Water-blocking system Optical Information MAXIMUM ATTENUATION (DB/KM) OVERFILL LAUNCH MIN. BANDWIDTH (MHZ KM) GIGABIT ETHERNET MIN. LINK DISTANCE (METERS) FIBER TYPE 850 NM 1300 NM 1310 NM 1550 NM 850 NM 1300 NM 850 NM 1300 NM (6) 62.5/125 GIGA-Link N/A N/A (8) 62.5/125 GIGA-Link N/A N/A (5) 50/125 GIGA-Link N/A N/A (7) 50/125 GIGA-Link N/A N/A (L) 50/125 Laser-Link N/A N/A (9) Single-mode N/A N/A N/A N/A N/A 5000 Gigabit Ethernet Minimum Link Distances are based on bandwidth /modal dispersion constraints. Actual link distances may be constrained by attenuation, depending on specific loss budget. or (800) , AFL, all rights reserved. PP , Revision 2,

29 Fiber Optic Cable Gel-Free LSZH Non-Armored Loose Tube (LL Series Gel-Free SJ) Mechanical Data NOMINAL NOMINAL MAXIMUM TENSILE LOAD MINIMUM BEND RADIUS NO. OF TUBES DIAMETER WEIGHT LBS (N) INCHES (CM) AFL NO. FIBER COUNT FIBERS/ TUBE INCHES (MM) LBS/1,000FT (KG/KM) SHORT TERM LONG TERM SHORT TERM LONG TERM LL012 C5101N1D 12 1/12 (4 fillers) 0.39 (9.8) 49 (73) 600 (2670) 180 (800) 7.8 (20) 3.9 (10) LL024 C5101N1D 24 2/12 (3 fillers) 0.39 (9.8) 49 (72) 600 (2670) 180 (800) 7.8 (20) 3.9 (10) LL036 C5101N1D 36 3/12 (2 fillers) 0.39 (9.8) 48 (72) 600 (2670) 180 (800) 7.8 (20) 3.9 (10) LL048 C5101N1D 48 4/12 (1 filler) 0.39 (9.8) 48 (71) 600 (2670) 180 (800) 7.8 (20) 3.9 (10) LL060 C5101N1D 60 5/12 (no fillers) 0.39 (9.8) 48 (71) 600 (2670) 180 (800) 7.8 (20) 3.9 (10) LL072 C6101N1D 72 6/12 (no fillers) 0.42 (10.6) 55 (82) 600 (2670) 180 (800) 8.4 (21) 4.2 (11) LL096 C8101N1D 96 8/12 (no fillers) 0.48 (12.3) 75 (118) 600 (2670) 180 (800) 9.6 (25) 4.8 (12) LL144 CC101N1D /12 (no fillers) 0.62 (15.8) 119 (178) 600 (2670) 180 (800) 12.4 (32) 6.2 (16) LL216 CI301N1D /12 (no fillers) 0.62 (15.8) 110 (163) 600 (2670) 180 (800) 12.4 (32) 6.2 (16) LL288 CO301N1D /12 (no fillers) 0.75 (19.1) 148 (220) 600 (2670) 180 (800) 15.0 (38) 7.5 (19) Note: Diameter and weight subject to change without notice Fiber Types Replace asterisk ( ) in AFL number with number corresponding to desired fiber type below. 5 = 50/125 µm multimode GIGA-Link = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link 1000 Gel-Free LSZH Single-Jacket Single-Armor Loose Tube (LL Series Gel-Free SASJ) Mechanical Data NOMINAL NOMINAL MAXIMUM TENSILE LOAD MINIMUM BEND RADIUS NO. OF TUBES DIAMETER WEIGHT LBS (N) INCHES (CM) AFL NO. FIBER COUNT FIBERS/ TUBE INCHES (MM) LBS/1,000FT (KG/KM) SHORT TERM LONG TERM SHORT TERM LONG TERM LL012 C5201S1D 12 1/12 (4 fillers) 0.50 (12.6) 95 (141) 600 (2670) 180 (800) 10.0 (25) 5.0 (13) LL024 C5201S1D 24 2/12 (3 fillers) 0.50 (12.6) 95 (141) 600 (2670) 180 (800) 10.0 (25) 5.0 (13) LL036 C5201S1D 36 3/12 (2 fillers) 0.50 (12.6) 94 (140) 600 (2670) 180 (800) 10.0 (25) 5.0 (13) LL048 C5201S1D 48 4/12 (1 filler) 0.50 (12.6) 94 (140) 600 (2670) 180 (800) 10.0 (25) 5.0 (13) LL060 C5201S1D 60 5/12 (no fillers) 0.50 (12.6) 94 (139) 600 (2670) 180 (800) 10.0 (25) 5.0 (13) LL072 C6201S1D 72 6/12 (no fillers) 0.53 (13.4) 105 (156) 600 (2670) 180 (800) 10.6 (27) 5.3 (13) LL096 C8201S1D 96 8/12 (no fillers) 0.59 (15.0) 127 (189) 600 (2670) 180 (800) 11.8 (30) 5.9 (15) LL144 CC201S1D /12 (no fillers) 0.73 (18.5) 182 (271) 600 (2670) 180 (800) 14.6 (37) 7.3 (19) Note: Diameter and weight subject to change without notice Fiber Types Replace asterisk ( ) in AFL number with number corresponding to desired fiber type below. 5 = 50/125 µm multimode GIGA-Link = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link 1000 L = 50/125 µm multimode Laser-Link = Single-mode Q = Non-zero dispersion-shifted single-mode K = SM Futureguide SR-15e Bend Insensitive or (800) , AFL, all rights reserved. PP , Revision 2,

30 Fiber Optic Cable Gel-Free Extreme Low Temp LSZH Double Jacket I/O Loose Tube (LA Series Gel-Free) The LA-Series is specially designed for applications that demand reliable performance in harsh environment installations. The cable construction incorporates a variety of packaging technologies that allow the product to operate in extremely low temperatures, mechanically abusive installations and highly caustic and acidic environments. The key to the reliable, ultra-high performance is the specially designed cable core and the dual layer jacketing system. The cable core is constructed using materials and engineered geometry that optimizes the isolation of the optical fibers from the stresses and strains imparted on the cable and commonly realized in extreme environments. The outer jacketing is designed to further protect the ruggedized core assembly with a myltiplying system made up of a double-ply, low smoke zero halogen (LSZH) flame resistant jacketing system that integrates a strong layer of aramid yarn between the inner and outer sheaths. Applications Network Connectivity for: Oil and Gas fields Low Temperature Environments Refineries Mining Mass Transit Temperature Specifications TEMPERATURE RANGE INSTALLATION -30ºC to +50ºC OPERATING -55ºC to +70ºC STORAGE -60ºC to +75ºC Features Gel-Free buffer tubes Fiber Range Suitable for direct burial and tray installations per UL 1277 Increased tensile load rating 2X Crush Resistance compared to standard fiber optic cables 2X Cold Impact Resistance compared to standard fiber optic cables Self-supporting capability (contact factory for system design support) Specifications OFNG-LS Listed, CSA-FT4, IEEE1202 and UL 1685 Meets requirements of NFPA 130 and NFPA 502 for use in fixed guideway transit systems and road tunnels ICEA S CSA 22.2 No. 230 and 232 Fluid immersion testing per ASTM D412 Sunlight Resistant Jacket Oil Res II compliant Jacketing System Zero Halogen Per MIL PRF Mechanical PARAMETER Crush Cold Impact Tensile Installation Operational VALUE 440N/CM 8.8 N*m 1,000 lbs (4,450N) 400 lbs (1,780N) Cable Components Anti-buckling element Water blocking layer Inner FR-LSZH jacket Outer FR-LSZH chemical-resistant jacket Gel-free buffer tube Optical fibers Aramid cut-resistant matrix Rip cord Rodent-deterrent Jacket Option Available or (800) , AFL, all rights reserved. PP , Revision 6,

31 Fiber Optic Cable Gel-Free Extreme Low Temp LSZH Double Jacket I/O Loose Tube (LA Series Gel-Free) Fiber Specifications MAXIMUM ATTENUATION (DB/KM) OVERFILL LAUNCH MIN. BANDWIDTH (MHZ KM) GIGABIT ETHERNET MIN. LINK DISTANCE (METERS) FIBER TYPE 850 NM 1300 NM 1310 NM 1550 NM 850 NM 1300 NM 850 NM 1300 NM (6) 62.5/125 GIGA-Link N/A N/A (5) 50/125 GIGA-Link N/A N/A (L) 50/125 Laser-Link N/A N/A (9) Single-mode N/A N/A N/A N/A N/A 5000 (Q) Non-zero Dispersion-shifted Single-mode N/A N/A N/A 0.25 N/A N/A N/A N/A (K) AFL G.657.A1 Single-mode N/A N/A N/A N/A N/A 5000 Gigabit Ethernet Minimum Link Distances are based on bandwidth /modal dispersion constraints. Actual link distances may be constrained by attenuation, depending on specific loss budget. Ordering Information NOMINAL DIAMETER NOMINAL WEIGHT MAXIMUM TENSILE LOAD LBS (N) MINIMUM BEND RADIUS INCHES (CM) AFL NO. FIBER COUNT INCHES MM LBS/1,000 FT KG/KM INSTALLATION OPERATION INSTALLATION OPERATION LA012 C6111N1D (4400) 290 (1300) 13(29.4) 6 (14.6) LA024 C6111N1D (4400) 290 (1300) 13(29.4) 6 (14.6) LA048 C6111N1D (4400) 290 (1300) 13(29.4) 6 (14.6) LA072 C6111N1D (4400) 290 (1300) 13(29.4) 6 (14.6) LA096 C8111N1D (4400) 290 (1300) 15(32.6) 6 (16.2) LA144 CC111NI D (4400) 290 (1300) 18(396) 8 (19.7) LA288 C03111NI D (4400) 290 (1300) 20(45.4) 9 (22.6) Fiber Types Replace asterisk ( ) in AFL number with number in the Fiber Specifications table above. or (800) , AFL, all rights reserved. PP , Revision 6,

32 Fiber Optic Cable XLPO LSZH Gel Free I/O Loose Tube (LX Series) Consisting of thermoset (XLPO) jacket, AFL s LX-series of low-smoke zero-halogen (LSZH) loose tube cables are specifically designed for harsh environments. Ideal for indoor and outdoor industrial applications, the cable design includes dry-core water blocking system, SZ-stranded core for easy mid-span access to fibers, and a highly chemical resistant, cross-linked UV-resistant outer jacket. For even greater mechanical robustness, a corrugated steel armor version is available. Applications include mining, industrial, railways, subways, and much more. Applications Subway tunnels Railway right-of-way Airport terminals Confined space pathways Steam tunnels Petrochemical facilities Industrial Mining Shipboard Temperature Range Operating: -40ºC to +70ºC Storage: -50ºC to +75ºC Installation: -20ºC to +60ºC Crush * Armored: 550 N/cm (375 lbs/in) Non-armored: 440 N/cm (250 lbs/in) * Standard loose tube cables are 220 N/cm (125 lbs/in) Rodent-deterrent Jacket Option Available Features Fiber counts up to 288 Low smoke zero halogen, thermoset jacket Optional rodent resistant armor available Resistant to lubricating oil (Mil-L-23699), hydraulic fluid (Mil-H-5606), gasoline and deionized water Enhance Crush Resistance for installation in trays or other exposed runs Cable Components Maximum Lengths FRP central member Water blocking layer Strength member XLPO flame retardant LSZH jacket Gel-free buffer tube Optical fibers Optional inner jacket and steel armor Ripcord Specifications IEEE 1202, UL 1685, CSA 22.2 FT4 ANSI/ICEA-S , GR-20-CORE NEC OFN(C)G-LS listed (steel armor option) Meets or exceeds requirements of NFPA 130 and NFPA 502 Suitable for installation in trays per NFPA 70 SINGLE-MODE MULTIMODE FIBER COUNT FEET METERS FEET METERS ,000 7,000 23,000 7,000 Longer lengths may be available upon request. Optical Information MAXIMUM ATTENUATION (DB/KM) OVERFILL LAUNCH MIN. BANDWIDTH (MHZ KM) GIGABIT ETHERNET MIN. LINK DISTANCE (METERS) FIBER TYPE 850 NM 1300 NM 1310 NM 1550 NM 850 NM 1300 NM 850 NM 1300 NM (6) 62.5/125 GIGA-Link N/A N/A (8) 62.5/125 GIGA-Link N/A N/A (5) 50/125 GIGA-Link N/A N/A (7) 50/125 GIGA-Link N/A N/A (L) 50/125 Laser-Link N/A N/A (9) Single-mode N/A N/A N/A N/A N/A 5000 (K) SM Futureguide SR-15e Bend Insensitive N/A N/A N/A N/A N/A 5000 Gigabit Ethernet Minimum Link Distances are based on "bandwidth"/modal dispersion constraints. Actual link distances may be constrained by attenuation, depending on specific loss budget. or (800) , AFL, all rights reserved. PP , Revision 1,

33 Fiber Optic Cable XLPO LSZH Gel Free I/O Loose Tube (LX Series) Ordering Information NOMINAL NOMINAL MAXIMUM TENSILE LOAD MINIMUM BEND RADIUS DIAMETER WEIGHT LBS (N) INCHES (CM) AFL NO. FIBER COUNT NUMBER OF TUBES/FIBERS INCHES MM LBS/1,000 FT KG/KM SHORT TERM LONG TERM SHORT TERM LONG TERM NON-ARMORED (OFNG-LS) LX006 C5101N1D 6 1w/6 (4 fillers) (2670) 180 (800) 11 (22) 4 (11) LX012 C5101N1D 12 1w/12 (4 fillers) (2670) 180 (800) 11 (22) 4 (11) LX024 C5101N1D 24 2w/12 (3 fillers) (2670) 180 (800) 11 (22) 4 (11) LX036 C5101N1D 36 3w/12 (2 fillers) (2670) 180 (800) 11 (22) 4 (11) LX048 C5101N1D 48 4w/12 (1 filler) (2670) 180 (800) 11 (22) 4 (11) LX060 C5101N1D 60 5w/12 (no fillers) (2670) 180 (800) 11 (22) 4 (11) LX072 C5101N1D 72 6w/12 (no fillers) (2670) 180 (800) 11 (24) 5 (12) LX096 C8101N1D 96 8w/12 (2 fillers) (2670) 180 (800) 13 (27) 5 (13) LX144 CC101N1D w/12 (1 filler) (2670) 180 (800) 15 (34) 7 (17) LX288 CO301N1D w/12 (no fillers) (2670) 180 (800) 18 (40) 8 (19) ARMORED (OFCG-LS) LX006 C5111S1D 6 1w/6 (4 fillers) (2670) 200 (890) 12 (26) 5 (13) LX012 C5111S1D 12 1w/12 (4 fillers) (2670) 200 (890) 12 (26) 5 (13) LX018 C5111S1D 18 1w/12,1w/6 (3 fillers) (2670) 200 (890) 12 (26) 5 (13) LX024 C5111S1D 24 2w/12 (3 fillers) (2670) 200 (890) 12 (26) 5 (13) LX030 C5111S1D 30 2w/12,1w/6 (2 fillers) (2670) 200 (890) 12 (26) 5 (13) LX036 C5111S1D 36 3w/12 (2 fillers) (2670) 200 (890) 12 (26) 5 (13) LX048 C5111S1D 48 4w/12 (1 filler) (2670) 200 (890) 12 (26) 5 (13) LX060 C5111S1D 60 5w/12 (no fillers) (2670) 200 (890) 12 (26) 5 (13) LX072 C5111S1D 72 6w/12 (no fillers) (2670) 200 (890) 13 (28) 5 (14) LX096 C8101S1D 96 8w/12 (2 fillers) (2670) 180 (800) 14 (31) 6 (15) LX144 CC101S1D w/12 (1 filler) (2670) 180 (800) 17 (38) 7 (19) LX288 CO301S1D w/12 (no fillers) (2670) 180 (800) 19 (44) 9 (22) NOTES: 1. Diameter and weight subject to change without notice. 2. For other types of LSZH Cables, please contact your AFL Representative. Fiber Types-Replace asterisk ( ) in AFL number with number corresponding to desired fiber type below 5 = 50/125 µm multimode GIGA-Link = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link 1000 L = 50/125 µm multimode Laser-Link = Single-mode Q = Non-zero dispersion-shifted single-mode K = SM Futureguide SR-15e Bend Insensitive Reel Information REEL A REEL B REEL C REEL D REEL E ITEM INCHES CM INCHES CM INCHES CM INCHES CM INCHES CM Reel Height Reel Width Outside Reel Width Inside Drum Diameter Arbor Hole Diameter Reel Weight With Lagging 180 lbs 82 kg 420 lbs 191 kg 685 lbs 311 kg 710 lbs 320 kg 950 lbs 431 kg AFL typically provides Loose Tube cable on several standard sizes of non-returnable wooden reels. Non-standard reel sizes are available upon request. Larger reel sizes may be required to accommodate long cable lengths. or (800) , AFL, all rights reserved. PP , Revision 1,

34 Fiber Optic Cable Tactical Tight Buffered Cable AFL Tactical Tight Buffered Cables are ideal for use in installations where extreme environmental conditions are present. Designed to be deployed and retrieved in the field, AFL s Tactical Tight Buffered Cables are highly resistant to damage caused by repeated impacts crushing forces, abrasion and extreme temperatures. Temperature Specifications TEMPERATURE RANGE INSTALLATION -46ºC to +85ºC OPERATING -46ºC to +85ºC STORAGE -55ºC to +85ºC Features Cut resistant polyurethane jacket with flame retardant options available Highly flexible construction allows for multiple deployments All aramid strength members Performance in wide temperature range High impact and crush resistance Durable in high traffic areas MIL-PRF qualified fiber available (-RH designation) Tested to meet MIL-PRF Cable Components Applications Field deployment in abusive environments Temporary installation of critical communications lines where quick retrieval and re-use is necessary High Traffic areas Security and Sensing applications Broadcast deployments Installations in harsh environments Polyurethane outer jacket aramid strength member 250 µm or 500 µm optical fiber 900 µm Elastomeric Tight Buffer Specifications CHARACTERISTIC TEST PROCEDURE PERFORMANCE Tensile and elongation EIA/TIA Operating tensile strength EIA/TIA Low-temp flexibility EIA/TIA Cyclic flexing EIA/TIA Crush resistance EIA/TIA N/cm or greater Impact EIA/TIA Temperature cycling EIA/TIA C to 85 C Temperature/humidity cycling EIA/TIA Method B Life aging EIA/TIA Freezing water immersion EIA/TIA Rodent-deterrent Jacket Option Available or (800) , AFL, all rights reserved. PP , Revision 7,

35 Fiber Optic Cable Tactical Tight Buffered Cable Mechanical Data AFL NO. FIBER COUNT NOMINAL DIAMETER NOMINAL WEIGHT MAXIMUM TENSILE LOAD LBS (N) MINIMUM BEND RADIUS INCHES (CM) INCHES (MM) LBS/1000FT (KG/KM) INSTALLATION LONG TERM INSTALLATION LONG TERM X%001*30180H (3.0) 5.4 (8) 135 (600) 40 (178) 1.8 (4.5) 1.2 (3.0) X%001*40180H (4.0) 9.1 (13.5) 180 (800) 54 (240) 2.4 (6.0) 1.6 (4.0) X%001*46180H (4.6) 12.2 (18.1) 180 (800) 54 (240) 2.7 (6.9) 1.8 (4.6) X%002*55180H (5.5) 16.2 (25) 400 (1780) 130 (578) 2.2 (5.5) 1.1 (2.8) X%004*55180H (5.5) 16.2 (25) 400 (1780) 130 (578) 2.2 (5.5) 1.1 (2.8) X%002*58180H (5.8) 21.5 (32) 400 (1780) 130 (578) 3.4 (8.7) 2.3 (5.8) X%004*58180H (5.8) 21.5 (32) 400 (1780) 130 (578) 3.4 (8.7) 2.3 (5.8) X%006*61180H (6.1) 22.2 (33) 400 (1780) 130 (578) 3.6 (9.2) 2.4 (6.1) X%008*64180H (6.4) 28.8 (44) 470 (2090) 160 (712) 2.5 (6.4) 1.3 (3.2) X%012*64180H (6.4) 30.8 (47) 470 (2090) 160 (712) 2.5 (6.4) 1.3 (3.2) X%024*85180H (8.5) 38.7 (59) 670 (2980) 220 (979) 3.3 (8.5) 1.7 (4.3) Note: Diameter and weight subject to change without notice Replace percent (%) in AFL No. with corresponding jacket type below. 1 = Tactical Polyurethane 2 = Flame Retardant Polyurethane 3 = LSZH Polyurethane 4= StrataJac Tactical+ Encapsulation Replace asterisk (*) in AFL No. with corresponding fiber type below. 5 = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = Single-mode K = SM Futureguide SR-15e Bend Insensitive L = 50/125 µm OM3 C = 50/125 µm OM4 500 µm primary coated fiber available. Customer specified print available. See Tactical Cable Ordering Guide on page 16 for AFL No. designations. or (800) , AFL, all rights reserved. PP , Revision 7,

36 Fiber Optic Cable Tactical Breakout Cable AFL s Tactical Breakout Cables are ideal for use in harsh environment applications requiring a rugged deployable cable solution. Consisting of 2 mm sub-cables, each optical fiber is suitable for direct termination enabling fast and easy installation. This reduced diameter, light weight and high strength cable features a tough abrasion resistant polyurethane jacket that offers exceptional performance through a wide range of temperatures. It is also impervious to common chemicals found in industrial environments. Available with a flame retardant jacket option the BU series breakout cable is ideal for use in mines, petrochemical facilities and other industrial applications. Features Deployable design UV, Fungus and water resistant Highly crush and impact resistant 2.0 mm sub-cables available in a variety of colors Available with shiny or matte low-friction jacket Custom colors available Available with bend insensitive SM and MM optical fiber Supports all multi-gigabit Ethernet standards RoHS compliant Specifications MIL PRF ANSI/ICEA-S RoHS Compliant Highly abrasion and cut resistant Resistant to most fuels, oils and greases Excellent low-temperature flexibility Temperature Range Operating: -55 C to +85 C Storage: -60 C to +85 C Installation: -50 C to +85 C Cable Components Polyurethane Jacket Filler 2 mm Subunit Hytrel Tight Buffered Fiber Flexible Center Member Aramid Strength Member Mechanical PARAMETER VALUE Tensile Installation 2112 (475) Operational 333 (75) Rodent-deterrent Jacket Option Available , AFL, all rights reserved. PP , Revision 4,

37 Fiber Optic Cable Tactical Breakout Cable Ordering Information AFL NO. NOMINAL NOMINAL MINIMUM FIBER PHYSICAL PROPERTIES DIAMETER WEIGHT BEND RADIUS COUNT INCHES MM LBS/1,000 FT KG/KM CRUSH (N/CM) IMPACTS INCHES (CM) B%002*2018XH (7.8) B%002*2018XH (7.5) B%004*2018XH (7.8) B%004*2018XH (7.5) B%006*2018XH (8.8) B%008*2018XH (10) B%012*2018XH (11.4) Replace percent (%) in AFL No. with corresponding jacket type below. 1 = Tactical Polyurethane 2 = Flame Retardant Polyurethane 3 = LSZH Polyurethane 4= StrataJac Tactical+ Encapsulation Replace asterisk (*) in AFL No. with corresponding fiber type below. 5 = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = Single-mode K = SM Futureguide SR-15e Bend Insensitive L = 50/125 µm OM3 C = 50/125 µm OM4 500 µm primary coated fiber available. Customer specified print available. See Tactical Cable Ordering Guide on page 16 for AFL No. designations , AFL, all rights reserved. PP , Revision 4,

38 Fiber Optic Cable Tactical Copper/Fiber Composite Cable AFL s tactical copper/fiber composite cables are ruggedized and easy to use in rapid deployment networks and other applications requiring high mechanical performance standards, environmental exposure, or dynamic end use where low voltage power and high speed fiber optic communications are combined. Constructed as a breakout style cable, each optical fiber has enhanced protection in an elastomeric sub-cable jacket. Additionally, each electrical conductor is constructed utilizing high strand count copper with premium ETFE insulation. Offered in a tactical breakout cable construction, AFL s tactical copper/fiber composite cable offers excellent tensile strength, crush resistance, impact resistance, bending performance and a wide operating temperature range. And with AFL s selection of tactical cable jacket materials, the cable can be used in applications requiring exposure to UV, moisture, industrial chemicals or confined spaces. Applications Military Broadcast Petrochemical Rail Mining Rodent-deterrent Jacket Option Available Features Highly flexible for rapid deployment and ease of installation Ruggedized tactical cable design for operating in harsh conditions Combination power and fiber minimizes number of cables and saves space Supports all formats of high speed optical networking Performance Data Testing per MIL PRF CHARACTERISTIC PERFORMANCE Testing per Installation Tensile Load 540 lbs Operating Tensile Load 135 lbs Min. Bend Radius Short Term 7.8 cm Min. Bend Radius Long Term 3.9 cm Operating Temperature -55 C to +85 C Storage Temperature -60 C to +85 C Crush Resistance 2000 N/cm of cable OD Impact Resistance 200 Flex Resistance 2000 Ordering Information AFL NO. MAXIMUM ATTENUATION (db/km) OVERFILLED LAUNCH MINIMUM BANDWIDTH (MHz km) 1 GIGABIT ETHERNET MINIMUM LINK DISTANCE (METERS) 850 nm 1300 nm 1550 nm 850 nm 1300 nm 850 nm 1300 nm 10 GIGABIT ETHERNET MINIMUM LINK DISTANCE (METERS) 850 nm 1300 nm (Serial) (Serial) B%002*2018XH-2CU16 N/A N/A N/A N/A N/A N/A N/A Replace percent (%) in AFL No. with corresponding jacket type below. 1 = Tactical Polyurethane 2 = Flame Retardant Polyurethane 3 = LSZH Polyurethane 4= StrataJac Tactical+ Encapsulation Replace asterisk (*) in AFL No. with corresponding fiber type below. 5 = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = Single-mode K = SM Futureguide SR-15e Bend Insensitive L = 50/125 µm OM3 C = 50/125 µm OM4 500 µm primary coated fiber available. Customer specified print available. See Tactical Cable Ordering Guide on page 16 for AFL No. designations. or (800) , AFL, all rights reserved. PP , Revision 2,

39 Fiber Optic Cable Ruggedized Indoor/Outdoor Breakout Cable AFL Ruggedized Indoor/Outdoor Riser Breakout cable is suited for applications requiring a high performance fiber optic cable. Water-blocked and re-inforced with all-dielectric strength members within the core, this cable can withstand the rigors presented by higher end installations. Available in 2-12 fiber counts, these cables feature a UV-and Fungal-Resistant semi-pressure extrueded outer jacket. Individual sub-units measure 2.5 mm, allowing for ease of field termination. Sub-units are also water-blocked adding to the overall protection of the fiber optic components from environmental damage. Temperature Specifications TEMPERATURE RANGE INSTALLATION -20ºC to +70ºC OPERATING -40ºC to +70ºC STORAGE -40ºC to +70ºC Cable Components Features Fungus, water and UV-resistant PVC jacket featuring SP extrusion technology Riser-rated with water-blocked sub-units Sub-units and tight buffer available in a variety of colors Tested to meet or exceed GR-409-CORE and ICEA-S Compliant to Directive 2002/95/EC (RoHS) MSHA approved for mining applications Applications Harsh Environment Mining Industrial Campus Environment 2 and 4 Fiber PVC outer jacket 2.5mm water-blocked simplex sub-unit - 900µm buffered fiber - water swellable aramid yarn strength members - PVC jacket aramid yarn strength member 12 Fiber PVC outer jacket 2.5mm simplex sub-unit - 900µm buffered fiber - water swellable aramid yarn strength members - PVC jacket strength member aramid yarn Fiber Specifications OVERFILL LAUNCH MAXIMUM ATTENUATION MIN. GIGABIT ETHERNET 10 GIGABIT CORE SIZE/ (DB/KM) BANDWIDTH EMBc MIN. LINK DISTANCE ETHERNET MIN. LINK FIBER TYPE ISO/ (MHZ KM) (MHZ KM) (METERS) DISTANCE (METERS) IEC 850 NM 1300 NM 1550 NM 850 NM 1300 NM 850 NM 1300 NM 850 NM 1300 NM (6) 62.5 Giga-Link 300 OM N/A N/A (5) 50 Giga-Link 600 OM N/A N/A (A) 50 Laser-Link 150 OM N/A (L) 50 Laser-Link 300 OM N/A (C) 50 Laser-Link 550 OM N/A (K) AFL G.657.A1 Single-mode OS2 N/A N/A N/A N/A N/A 5000 N/A 10,000 (9) SM OS2 N/A N/A N/A N/A N/A 5,000 N/A 10,000 A or (800) , AFL, all rights reserved. PP , Revision 2,

40 Fiber Optic Cable Ruggedized Indoor/Outdoor Breakout Cable Mechanical Data AFL NO. FIBER COUNT NOMINAL DIAMETER WEIGHT TENSION LBS (N) BENDING RADIUS INCHES (CM) INCHES (MM) LBS/1000FT (KG/KM) INSTALLATION LONG TERM INSTALLATION LONG TERM BM ## (8.6) 49 (73) 300 (1334) 90 (400) 5.0 (12.6) 3.3 (8.4) BM ## (8.6) 49 (73) 300 (1334) 90 (400) 5.0 (12.6) 3.3 (8.4) BM ## (10.1) 69 (102) 300 (1334) 90 (400) 6.02 (15.3) 4.1 (10.2) BM ## (11.8) 93 (138) 300 (1334) 90 (400) 7.0 (18.0) 4.6 (11.8) BM ## (13.0) 95 (142) 300 (1334) 90 (400) 8.0 (20.0) 5.3 (13.5) Fiber Types Replace asterisk ( ) in AFL number with number in the Fiber Specifications table on previous page. # Outer Jacket Color Replace hashtag (#) in AFL number with number in the Cable Jacket Color table below. Cable Jacket Color Options 1 - Blue 8 - Black 2 - Orange 9 - Yellow 3 - Green A - Violet 4 - Brown B - Rose 5 - Slate C - Aqua 6 - White K - Erika Violet (RAL 4003) 7 - Red Cable Length - Reel Size ITEM REEL F Reel Height (inches) 42 Reel Outside Width (inches) 36 Drum Diameter (inches) 23 Reel Weight (lbs) 148 CAPACITY: meters (feet) 4 Fiber Breakout 1,500 / (5,000) 6 Fiber Breakout 1,500 / (5,000) 8 Fiber Breakout 1,500 / (5,000) 12 Fiber Breakout 1,500 / (5,000) A or (800) , AFL, all rights reserved. PP , Revision 2,

41 Fiber Optic Cable Braided Armored Tactical Tight Buffered Cable AFL Armored Tactical Tight Buffered Cables are ideal for use in installations where extreme environmental conditions are present. With the addition of a wire braid embedded within the jacketing system, these cables are highly resistant to damage caused by repetitive impacts, high flex, crush, and abrasion as well as other harsh conditions. By utilizing AFL's tight buffered fiber technology field, termination is simplified. Temperature Range Operating: -46ºC to +85ºC Installation: -20ºC to +85ºC Storage: -57 C to +85 C Rodent-deterrent Jacket Option Available Features Cut resistant polyurethane outer jacket Highly flexible construction allows for multiple deployments Performance in wide temperature range High impact and crush resistance Durable in high traffic areas Water and UV resistant Multiple jacket colors available Capable of supporting all Multi-Gigabit Ethernet Protocols Cable Components Tight Buffered Fiber Bronze Braiding Aramid Yarn Inner TPU Jacket Outer TPU Jacket Applications Field deployment in abusive environments High traffic areas Security and sensing applications High Flex Applications Installations in industrial environments Temporary installation of critical communications lines where quick retrieval and re-use is necessary Ordering Information FIBER NOMINAL DIAMETER NOMINAL WEIGHT TENSION LBS (N) MINIMUM BEND RADIUS AFL NO. COUNT INCHES MM LBS/1,000 FT KG/KM INSTALLATION LONG TERM INCHES (CM) X%001*30180#-BB (1112) 66 (290) 2.6 (6.6) X%002*58180#-BB (1450) 66 (290) 3.7 (9.5) X%004*58180#-BB (1450) 66 (290) 3.7 (9.5) X%006*61180#-BB (1450) 66 (290) 3.8 (9.8) X%012*70180#-BB (1750) 79 (350) 4.2 (10.7) Note: Diameter and weight subject to change without notice Replace percent (%) in AFL No. with corresponding jacket type below. 1 = Tactical Polyurethane 2 = Flame Retardant Polyurethane 3 = LSZH Polyurethane 4= StrataJac Tactical+ Encapsulation Replace asterisk (*) in AFL No. with corresponding fiber type below. 5 = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = Single-mode K = SM Futureguide SR-15e Bend Insensitive L = 50/125 µm OM3 C = 50/125 µm OM4 Replace pound sign (#) in AFL number with number corresponding below. G = 500 µm Coated Optical Fiber H = 250 µm Coated Optical Fiber 500 µm primary coated fiber available. Customer specified print available. See Tactical Cable Ordering Guide on page 16 for AFL No. designations. or (800) , AFL, all rights reserved. PP , Revision 2,

42 Fiber Optic Cable Braided Armored Tactical Breakout Cable AFL s Braided Armored Tactical Breakout Cables are ideal for use in harsh environment applications requiring a rugged deployable cable solution. Consisting of 2 mm sub-cables, each optical fiber is suitable for direct termination enabling fast and easy installation. This reduced diameter, light weight, and high strength cable features a tough abrasion resistant polyurethane jacket that offers exceptional performance through a wide range of temperatures. It is also impervious to common chemicals found in industrial environments. Available with a flame retardant jacket option the BU series breakout cable is ideal for use in mines, petrochemical facilities, and other industrial applications. Temperature Range Operating: -55C to +85C Storage: -60C to +85C Installation: -50C to +85C Mechanical PARAMETER VALUE Tensile Installation 2112 (475) Operational 333 (75) Rodent-deterrent Jacket Option Available Features Deployable design UV, Fungus, and water resistant Highly crush and impact resistant 2.0 mm sub-cables available in a variety of colors Available with shiny or matte low-friction jacket Custom colors available Available with bend insensitive SM and MM optical fiber Supports all multi-gigabit Ethernet standards RoHS compliant Specifications MIL PRF ANSI/ICEA-S RoHS Compliant Highly abrasion and cut resistant Resistant to most fuels, oils and greases Excellent low-temperature flexibility Braid application per IEEE 1580 available Cable Components 2 mm Breakout Unit Bronze Braiding Inner TPU Jacket Outer TPU Jacket Ordering Information AFL NO. FIBER COUNT NOMINAL DIAMETER NOMINAL WEIGHT PHYSICAL PROPERTIES INCHES MM LBS/1,000 FT KG/KM CRUSH (N/CM) IMPACTS B% XH-BB (11.5) B% XH-BB (11.5) B% XH-BB (12.5) B% XH-BB (13.7) B% XH-BB (15.5) MINIMUM BEND RADIUS INCHES (CM) Replace percent (%) in AFL No. with corresponding jacket type below. 1 = Tactical Polyurethane 2 = Flame Retardant Polyurethane 3 = LSZH Polyurethane 4= StrataJac Tactical+ Encapsulation Replace asterisk (*) in AFL No. with corresponding fiber type below. 5 = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = Single-mode K = SM Futureguide SR-15e Bend Insensitive L = 50/125 µm OM3 C = 50/125 µm OM4 500 µm primary coated fiber available. Customer specified print available. See Tactical Cable Ordering Guide on page 16 for AFL No. designations. or (800) , AFL, all rights reserved. PP , Revision 2,

43 Fiber Optic Cable Industrial Loose Tube Cable, LSZH, OFCG-LS, Aluminum Interlock Armor AFL s Industrial Loose Tube Cables are designed for high reliability in heavy industrial and harsh environment applications. Consisting of a formed metallic armor, the cable features superior crush resistance and a high degree of flexibility. Furthermore, the cable features a flame retardant LSZH jacket which is UV stabilized and highly resistant to chemicals commonly found in industrial environments. With an OFCG-LS listing, the cable is suitable for both indoor and outdoor industrial installations. Temperature Range Operating: -40C to +70C Storage: -60C to +50C Installation: -20C to +50C Mechanical PARAMETER VALUE Tensile Installation 2670 (600) Operational 800 (180) Features Eliminates need for conduit Simplified one-step installation Highly crush resistant Resistant to lubricating oil, gasoline, deionized water and many other chemicals Gel-free buffer tubes SZ stranded for quick easy access Available with bend insensitive SM and MM optical fiber Supports all multi-gigabit Ethernet standards Cable Components Specifications OFCG-LS, IEEE 1202 / FT4, UL1685 ANSI/ICEA-S CSA 22.2 #230 and #232 NFPA 130 / 502 RoHS Compliant Sun light resistant Oil Res II compliant jacketing system Central Member LSZH Outer Jacket Aluminum Interlocking Armor Ripcord Gel-Free Buffer Tube LSZH Inner Jacket Ordering Information NOMINAL DIAMETER NOMINAL WEIGHT MINIMUM BEND RADIUS FIBER # OF BUFFER TUBES / FIBERS INSTALLATION OPERATION (10XOD) IN/CM AFL NO. COUNT PER TUBE INCHES MM LBS/1,000 FT KG/KM (20XOD) IN/CM LL0 - - C5111A1D / /38 7.5/19.1 LL072 C6111A1D / /42 8.1/21 LL096 C8111A1D / /44 8.7/22 LL144 CC111A1D / /49 9.6/24.5 LL288 CO311A1D / / /28.9 Please specify fiber type when ordering (see below) 5 = 50/125 µm multimode GIGA-Link = 50/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = 62.5/125 µm multimode GIGA-Link = 9/125 µm single-mode L = 50/125 µm multimode Laser-Link 300 for 10 Gigabit Ethernet K = Single-mode Futureguide SR-15e Bend Insensitive or (800) , AFL, all rights reserved. PP , Revision 0,

44 Fiber Optic Cable High Strength Steel Wire (HSSW) Armored Fiber Optic Cable AFL s High Strength Steel Wire (HSSW) Armored Fiber Optic Cable provides the reliability needed for network backbones in harsh environment conditions. The high strength, galvanized plow steel armor is enhanced and offers a significant improvement in mechanical performance as compared to traditional steel tape armored cables. With a near ten-fold improvement in tensile performance, a two-fold improvement in crush resistance and a three-fold improvement in impact energy resistance, AFL s HSSW Armored Fiber Optic Cable provides the strength and durability needed for the most extreme conditions. Ideal for use as a direct buried cable in heavy construction zones including wind farm developments, pipelines, oil and gas fields, heavy industrial sites and a variety of additional harsh environments, AFL s HSSW Armored Cable meets or exceeds all requirements specified in Telcordia GR-20-Core. Cable Components Physical Properties PARAMETER VALUE Fiber Count 1-60 * Nominal Diameter 0.65 inches / 16.5 mm Nominal Weight 335 lbs/1000 ft. / 500 kg/km Maximum Tensile Load 5,000 lbs/ 22.2 kn ** Minimum Bend Radius 13 inches / 33 cm Termperature Range Installation: -40oC to + 70oC Operation: -50oC to + 70oC *** * Any combination of up to 60 fibers available ** Higher strength options available upon request *** Expanded temperature ranges available upon request or (800) , AFL, all rights reserved. PP , Revision 3,

45 22S (with Cleaver for scale) Workstation in Transit Case Fujikura 22S Fusion Splicer The Fujikura 22S active cladding alignment fusion splicer bridges the long standing gap between core alignment and fixed v-groove fusion splicer technology. Moveable v-grooves eliminate splicer errors due to dust and other contaminants. Despite its incredibly small size, this ruggedized, full-featured unit offers unmatched versatility for splicing in the most challenging environments. The innovative transit case and work tray provide multiple options for the best utilization of available work space while the long life battery provides power for up to 200 splice cycles which include application of the splice protection sleeve. The Fujikura 22S incorporates features typically found only in more expensive models. Removable sheath clamps allow the use of fiber holders if desired. The large 4.7" monitor provides a crystal clear image, even in the brightest sunlight, for evaluating splice quality. The electrode life has been extended to 3,000 splices, minimizing downtime for replacement and stabilization. Software updates are accomplished via the internet allowing users to quickly update their software as new splice programs become available. The fully ruggedized chassis provides for shock, dust and moisture protection while the two camera observation system provides for accurate fiber alignment and loss estimation calculations. The Fujikura 22S is also fully compatible with the FUSEConnect line of fusion installable connectors. Backed by the best service team in the industry, the Fujikura 22S is the ideal splicer to use when portability, ruggedness, versatility and reliability are needed for your splicing application. Features Dual camera, active cladding alignment technology World s smallest active clad alignment splicer at 4.72"W x 7.44"D x 2.8"H Fully ruggedized for shock, moisture and dust resistance Transit case converts to easy to use workstation Extended life electrodes Long life battery (200 splices/shrinks per charge) Auto start tube heater Workstation on Transit Case Fujikura 22S Kit 1 Ordering Information DESCRIPTION Fujikura 22S Fusion Splicer Includes: Fujikura 22S Fusion Splicer, S21A Sheath Clamp, ADC-19 AC Adapter, BTR-11 Battery Pack (installed), ACC-09 Power Cord, ELCT2-12 Spare Electrodes (pair), Operation Manual on CD, Quick Reference Guide, AP-01 Alcohol Container,SD01 Screwdriver and CC-32 Transit Case Fujikura 22S Fusion Splicer Kit 1 Includes: Fujikura 22S Fusion Splicer, CT-30A Cleaver, S21A Sheath Clamp, ADC-19 AC Adapter, BTR-11 Battery Pack (installed), ACC-09 Power Cord, ELCT2-12 Spare Electrodes (pair), Operation Manual on CD, Quick Reference Guide, AP-01 Alcohol Container, SD01 Screwdriver and CC-32 Transit Case Fujikura 22S Fusion Splicer Kit 2 Includes: Fujikura 22S Fusion Splicer, CT-06A Cleaver, S21A Sheath Clamp, ADC-19 AC Adapter, BTR-11 Battery Pack (installed), ACC-09 Power Cord, ELCT2-12 Spare Electrodes (pair), Operation Manual on CD, Quick Reference Guide, AP-01 Alcohol Container, SD01 Screwdriver and CC-32 Transit Case One Year Extended Warranty Two Year Extended Warranty AFL NO. S S S S S , AFL, all rights reserved. PP , Revision 2,

46 Fujikura 22S Fusion Splicer Recommended Accessories for the 22S DESCRIPTION AFL NO. DESCRIPTION AFL NO. Cleavers FUSEConnect Accessories CT-06A Cleaver S FH-FC-20 (900 µm within 2.0 mm sheathing) (each) S CT-30A Cleaver S FH-FC-30 (900 µm within 3.0 mm sheathing) (pair) S Fiber Holders FH-FC-900 (900 µm cable) (each) S FH Fiber Holder (250 µm single fiber) S CLAMP-FC-2000 (pair) S FH Fiber Holders (900 µm single fiber) S CLAMP-FC-3000 (pair) S FH-60-LT900 (900 µm loose buffer tube) S Miscellaneous Sheath Clamps Worktable Set S CLAMP-S21A Sheath Clamp S TS-01 Tripod Screw S CLAMP-S21B Sheath Clamp (900 μm diameter loose tube fiber (5-16 mm cleave)) Batteries BTR-11 Battery Pack S S ELCT2-12 Electrodes ADC-19 AC Adapter ACC-09 Power Cord AP-01 Alcohol Container S S S S SD-01 Screwdriver S CC-32 Transit Case S Splicer V-Groove Cleaning Kit S Specifications PARAMETER VALUE Applicable Fibers Single-mode (G.652 & G.657), Multimode (G.651), DSF (G.653), NZDS (G.655) Cladding Diameter 125 μm Coating Diameter 100 μm to 3000 μm Fiber Cleave Length 5 mm to 16 mm Typical Average Splice Loss 0.03 db (SM), 0.01 db (MM), 0.05 db (DS) and 0.05 db (NZDS) Splicing Time Typical 9 sec with SM Arc Calibration Method Automatic, real-time and by using results of previous splice when in AUTO mode, manual arc calibration function available Splicing Modes Total 100 splice modes Splice Loss Estimate Based on dual camera cladding alignment data Storage of Splice Result Last 2,000 splices Fiber Display 4.7 inch TFT color LCD with X or Y view or both X and Y view simultaneously Magnification 200X magnification for X/Y view Viewing Method 2 axis CMOS camera Operating Condition Altitude: 0 to 3,660 m above sea level, -10 to 50 C, Humidity: 0 to 95% RH, non-dew Mechanical Proof Test 1.96 N Tube Heater 30 heating modes Tube Heating Time Typical 24 sec with FP-60 (60 mm) sleeve Protection Sleeve Length 60 mm, 40 mm, micro Splice/Heat Cycles with Battery Typical 200 cycles with BTR-11 Electrode Life 3,000 splices Power Supply Auto select from 100 V to 240 V with AC adapter, 14.8 V DC with installed battery Terminals USB 2.0 Wind Protection Maximum wind velocity of 15 m/s. (34 mph) Dimensions 120 x 189 x 71 (mm) / 4.72" x 7.44" x 2.8" (inches) Weight 1.14 kg (2.51 lbs) with battery , AFL, all rights reserved. PP , Revision 2,

47 70S+ In case with lid detached Fujikura 70S+ Fusion Splicer The Fujikura 70S+ is the world s fastest and most robust core alignment fusion splicer. Incorporating the proven ruggedized features pioneered by Fujikura, the 70S+ has added automated and enhanced user control features to increase splicing efficiency. A user programmable, automated wind protector expedites the splicing process by automatically closing to initiate the splice process, and opening upon splice completion. Fully programmable auto open sheath clamps open one or both sheath clamps, after the tensile test, to prepare the fiber for removal. A new automated clamshell design tube heater applies heat to both sides of the splice protection sleeve resulting in a 13-second shrink time. The result is a total splice process time of approximately 21 seconds! Ruggedness and durability are greatly enhanced by a mirror-less optical system and "severe-impact resistant" monitor. Battery capacity is now 200 splices/shrinks. An innovative transit case doubles as a built-in or mobile workstation and makes splicing easier than ever before. In an industry first, the 70S+ is also equipped with Bluetooth technology. This allows the splicer to actively communicate with Bluetooth enabled fiber preparation accessories making maintenance of fiber preparation tools easier than ever! The 70S+ will also be available without Bluetooth functionality. Features Bluetooth wireless communication Automated and programmable wind protector 13-second automated tube heater Fully ruggedized for shock, dust and moisture Li-ion battery with 200 splices/shrinks per charge 5 mm cleave length for splice on connector or small package needs Sheath clamp or fiber holder operation On-board training and support videos Multi-function transit case with integrated workstation Ordering Information DESCRIPTION 70S+ Fusion Splicer (machine only) Includes: ADC-18 AC Adapter, ACC-14 AC Cord, ELCT2-20A Spare Electrodes (pair), S70C Sheath Clamp, USB Cable, Alcohol Pot, Screw Driver, Splicer Carrying Strap, Quick Reference Guide, Video Instruction Manual and CC30 Transit Case with Carrying Strap 70S+ Fusion Splicer Kit (with cleaver) Includes: CT30A Cleaver, ADC-18 AC Adapter, ACC-14 AC Cord, ELCT2-20A Spare Electrodes (pair), S70C Sheath Clamp, USB Cable, Alcohol Dispenser, Screw Driver, Splicer Carrying Strap, Quick Reference Guide, Video Instruction Manual, and CC30 Transit Case with Carrying Strap 70S+ Fusion Splicer Kit (with cleaver, battery and cord) Includes: BTR-09 Battery, DCC-18 Battery Charge Cord, CT30A Cleaver, ADC-18 AC Adapter, ACC-14 AC Cord, ELCT2-20A Spare Electrodes (pair), S70C Sheath Clamp, USB Cable, Alcohol Dispenser, Screw Driver, Splicer Carrying Strap, Quick Reference Guide, Video Instruction Manual and CC30 Transit Case with Carrying Strap 70S+ Fusion Splicer Without Bluetooth (machine only) Includes: ADC-18 AC Adapter, ACC-14 AC Cord, ELCT2-20A Spare Electrodes (pair), S70C Sheath Clamp, USB Cable, Alcohol Pot, Screw Driver, Splicer Carrying Strap, Quick Reference Guide, Video Instruction Manual and CC30 Transit Case with Carrying Strap One Year Extended Warranty Two Year Extended Warranty AFL NO. S S S S S S , AFL, all rights reserved. PP , Revision 7,

48 Fujikura 70S+ Fusion Splicer Recommended Accessories for the 70S DESCRIPTION Cleavers CT-06A Cleaver CT-30A Cleaver Fiber Holders FH Fiber Holder (pair) FH Fiber Holder (pair) FH Fiber Holder (pair) FH-60-LT900 Fiber Holder (pair) FH-60-LT900 Single Side Fiber Holder FUSEConnect Accessories FH-FC-20 (900 µm within 2.0 mm sheathing) (each) FH-FC-30 (900 µm within 3.0 mm sheathing) (pair) FH-FC-900 (900 µm cable) (each) CLAMP-FC-2000 (pair) CLAMP-FC-3000 (pair) Sheath Clamps CLAMP-S70C Sheath Clamp (Coating diameter from 100 µm µm (5-16 mm cleave)) CLAMP-S70D Sheath Clamp (900 µm diameter loose tube fiber (5-16 mm cleave)) AFL NO. S S S S S S S S S S S S S S DESCRIPTION Batteries and Power Cords ADC-18 AC Adapter ACC-14 AC Power Cord BTR-09 Battery and DCC-18 Charge Cord BTR-09 Battery DCC-18 Battery Charge Cord DCC-12 Power Cord (connects AC Adapter to cigarette lighter socket) DCC-13 Power Cord (connects AC Adapter to power source via alligator clips) Miscellaneous ELCT2-20A Electrodes Portable Tripod Workstation (see product profile for more detail) ASW-02 Splicing Workstation (see product profile for more detail) JP-06 J-PLATE (70/19 Series) SL-01 Sleeve Loader Worktable Upper Worktable Lower Inner Box Set USB Cable CC-30 Transit Case Splicer V-Groove Cleaning Kit AFL NO. S S S S S S S S S S S S S S S S S S Specifications PARAMETER VALUE Model 70S+ Fusion Splicer Applicable Fibers Single-mode (G.652 & G.657), Multimode (G.651.1), DS (G.653), CS (G.654), NZDS (G.655 & G.656) and Erbium-doped fiber Cladding Diameter μm Coating Diameter 100 μm to 3,000 μm Fiber Cleave Length 5 to 16 mm Typical Average Splice Loss 0.02 db with SM, 0.01 db with MM, 0.04 db with DS, 0.04 db with NZDS, measured by cut-back method relevant to ITU-T standards Splicing Time ULTRA FAST mode 6 seconds; SM FAST mode 7 seconds; SM AUTO mode 10 seconds; AUTO mode 15 seconds with SM fiber Arc Calibration Method Automatic, real-time and by using results of previous splice when in AUTO mode, manual arc calibration function available Splicing Modes 100 preset and user programmable modes Splice Loss Estimate Based upon dual camera core axis alignment data Storage of Splice Result Last 2,000 results stored in the internal memory Fiber Display X or Y, or both X and Y simultaneously. Front or rear monitor display options with automated image orientation Magnification 320X for single X or Y view, or 200X for X and Y view Viewing Method Dual cameras with 4.7 inch TFT color LCD monitor Operating Condition 0 to 5,000 m above sea level, 0 to 95%RH and -10 to 50 C respectively Mechanical Proof Test 1.96 to 2.25N Tube Heater Built-in tube heater with 30 heating modes; auto-start function Tube Heating Time Typical 13 seconds with FP-03 sleeve, 17 seconds with FP3 (40), 5-16 seconds with Fujikura micro sleeves Protection Sleeve Length 60 mm, 40 mm, micro Splice/Heat Cycles with Battery Typical 200 cycles with power save functions activated Electrode Life 5,000 Arc Discharges Power Supply Auto voltage selection from 100 to 240 V AC or 10 to 15 V DC with ADC-18, 14.8 V DC with BTR-09 battery Terminals USB 1.1 (USB-B type) for PC communication. Mini-DIN (6-pin) for HJS-02/03 Wind Protection Maximum wind velocity of 15 m/s. (34 mph) Dimensions 146 W x 159 D x 150 H (mm) / 5.75 W x 6.25 D x 5.9 H (inches) Weight 2.5 kg (5.5 lbs) with AC adapter ADC-18; 2.7 kg (5.95 lbs) with BTR-09 battery , AFL, all rights reserved. PP , Revision 7,

49 FSM-100M FSM-100P Features Split V-groove clamping system Plasma Zone fiber positioning PAS and WSI New IPA alignment method for PM fibers Enhanced sweep arc technology Zero degree fiber handling for LDF Special functions for glass processing capability Fiber profile memory function New arc calibration technology Short cleave length capability Fast and accurate PANDA splice mode Ergonomic, production friendly design User selectable display on dual LCD monitors Internet firmware updates FSM-100M and FSM-100P Fusion Splicers Whether splicing similar fiber types or double clad LDF fibers for high power lasers, the ARCMaster series splicers provide multiple solutions for diverse production needs. With State of the ARC technology, the ARCMaster sets the standard for fusion splicing with a multitude of new features designed to make splicing easier. The patent-pending split V-groove fiber clamping system accommodates optical fiber ranges from 60 to 2000 μm for cladding or coating without changing V-grooves or fiber clamps. The Plasma Zone fiber positioning system incorporates multiple fiber and electrode positioning techniques to provide unprecedented versatility for splicing LDF, heat sensitive or small diameter fibers. With a new fiber imaging technology, Interrelation Profile Alignment (IPA), alignment and splicing capabilities are possible with virtually any PM fiber type. Longer fiber tapering application is possible with Fujikura s Sweep Arc technology. Incorporating PAS (cold fiber image) and WSI (warm image) technologies, the optical analysis system provides a number of advanced features including improved loss estimation capabilities, fiber image performance with both LDF, small or heat sensitive fibers. Users can program multi-step glass processing operations to include non-splicing operations such as generating tapers or lenses. Dual LCD monitors provide enhanced data and graphical information that is user-selectable during each stage of the splicing process. Both units are designed with the needs for production in mind and are suitable for the most popular production workstations. Ordering Information DESCRIPTION ARCMaster FSM-100M Fusion Splicer (machine only) Includes: FH fiber holders (pair), FH fiber holders (pair), spare electrodes (pair), ADC-15 AC adapter, ACC-02 AC power cord, USB cable, dust cleaning swab set, operation manual and software on CD, and transit case ARCMaster FSM-100M Fusion Splicer Kit * ARCMaster FSM-100P Fusion Splicer (machine only) Includes: FH fiber holders (pair), FH fiber holders (pair), FH fiber holders (pair), spare electrodes (pair), ADC-15 AC adapter, ACC-02 AC power cord, USB cable, dust cleaning swab set, operation manual and software on CD, and transit case ARCMaster FSM-100P Fusion Splicer Kit * One year extended warranty (extends factory warranty by one year) Two year extended warranty (extends factory warranty by two years) AFL NO. S S S S S S * Each splicer kit includes an RS01 Thermal Stripper, a CT-32 Cleaver and a SPA-RS02-08 Spacer for RS01 in addition to the items listed above , AFL, all rights reserved. PP , Revision 6,

50 FSM-100M and FSM-100P Fusion Splicers Specifications Accessories for the FSM-100M and FSM-100P PARAMETER VALUE Applicable Fiber Silica based Single-mode and Multimode glass fiber: SMF (G.652), MMF (G.651), NZDSF (G.655), EDF, DCF, LDF and PMF, etc. Fiber Dimension Cladding diameter: 60 to 500 µm Coating diameter: 100 to 2,000 µm Cleave Length Glass clamping: 8 to 10 mm (standard 9mm) Coating clamping: 3 to 5 mm (standard 4mm) Typical Splice Loss SMF: 0.03 db MMF: 0.02 db NZDSF/LDF: 0.05 db PMF: 0.06 db (FSM-100P) Splicing Time SMF/MMF: 15 sec. NZDSF/LDF: 25 sec. PMF (PANDA): 35 to 50 sec. (FSM-100P) PMF (IPA): 90 to 300 sec. (FSM-100P) Polarization Cross-Talk PMF (PANDA): -40 db / 0.6 degree (FSM-100P) PMF (IPA): -32 db / 1.4 degree (FSM-100P) Return Loss 60 db or more Heating Time FP-03 (40 mm): 30 sec. FP-03 (60 mm): 35 sec. Micro sleeves: 55 sec. Sweep Length ±5 mm Electrode Life 2,500 Arc Discharges (SMF G.652 splicing at 1mm gap) Electrode Gap 1 to 3 mm Electrode Offset -0.3 to +0.1 mm Proof Test 1.96 N to 2.45 N Dimensions (mm) 311W x 232D x 160H Weight (excluding AC adapter) Operation Temperature FSM-100M: 7.7 kg FSM-100P: 7.9 kg 0 C to 40 C at 0 to 95% RH (Non-Dew) Storage Temperature -40 C to 80 C Monitor Type Dual 4.1 inch TFT color LCD monitors Magnification 125 µm: 187 to 300 X 250 µm: 58 to 300 X 400 µm: 58 to 93 X DESCRIPTION High Strength Accessories High Strength Preparation Kit Includes: USC-02, AFL PowerStrip and AFL PowerCleave Ultrasonic Cleaner (USC-02) HTS-12 High Tensile Stripper - includes 250 µm blades (400 µm available) AFL PowerStrip High Tensile Stripper AFL PowerCleave High Strength Cleaver Strippers RS01 Thermal Stripper RS03-80 Thermal Stripper SPA-RS02-08 Spacer Electrodes ELCT2-25 Spare Electrodes (pair) Cleavers CT-32 Cleaver CT-38 Cleaver ( for 80 µm cladding) Fiber Holders (Pairs) FH Fiber Holder (55 µm - 71 µm) FH Fiber Holder (94 µm µm) FH Fiber Holder (118 µm µm) FH Fiber Holder (140 µm µm) FH Fiber Holder (170 µm -199 µm) FH Fiber Holder (200 µm -239 µm) FH Fiber Holder (240 µm -289 µm) FH Fiber Holder (290 µm -339 µm) FH Fiber Holder (340 µm -389 µm) FH Fiber Holder (390 µm -489 µm) FH Fiber Holder (490 µm -589 µm) FH Fiber Holder (590 µm -689 µm) FH Fiber Holder (690 µm -789 µm) FH Fiber Holder (790 µm -889 µm) FH Fiber Holder (890 µm -989 µm) FH-40-LT900 Fiber Holder Power and Cords ADC-15 AC Adapter (FSM-100M/P) ACC-02 AC Power Cord ADC-09A AC Adapter (RS01) ACC-09 AC Power Cord (for ADC-09) Miscellaneous CC-27 Transit Case (100 M/P) DCS-01 Dust Cleaning Swab HP Power Meter Coupling Adapter ILX Power Meter Coupling Adapter Fiber Holder Adapter for HP/ILX PM Splicer V-Groove Cleaning Kit AFL NO. S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S , AFL, all rights reserved. PP , Revision 6,

51 Robust Over-Mold Recoat (Over-coating) Features Automatic, easy operation Great recoating capability for colored and non-colored fibers Easy-to-exchange molds for common fiber sizes Compatible with high temperature (200ºC) recoating compounds and other special compounds Full programmable control of recoat and proof test recipes PC command codes for automated control FSR-02 Fiber Recoater To meet the small package requirements of OEMs, AFL offers the FSR-02 fiber recoater. The FSR-02 eliminates the need for splice protection sleeves by automatically recoating a fiber back to the near-original coating diameter after a splice is complete. The recoat diameter is slightly larger than the original fiber coating such that it overlaps the fiber coating at each end, providing a robust and durable over-mold. Programmable for recoating lengths from 4 to 50 mm and proof testing from 4 to 20 Newtons, this unit stores data for 100 cycles which are easily downloadable to a PC. For splices that may fail the proof test, the breaking load is displayed. A complete set of PC command codes enables simple integration into an automated production line. A compact and low profile design facilitates comfortable benchtop operation. A dual axis illumination system ensures good curing performance not only with clear coated fibers, but with colored fibers as well. The FSR-02 is compatible with not only common recoating compounds, but also special high temperature (200 C) recoating compounds and stiffer recoat materials suitable for 900 µm jacketed fibers. New chrome spattering technology improves the long-term durability of the mold surface and minimizes mold flash. Specifications PARAMETER VALUE Dimensions (W x D x H) 255 mm x 150 mm x 130 mm Weight 3.8 kg Power supply AC 100 to 240 V, 50 to 60 Hz Recoating time Injection 15 sec / Curing 15 sec Proof test 4 to 20 N (0.4 to 2 kgf), 0 to 60 seconds, programmable Data storage 100 recoat cycles, PC downloadable Fiber coating diameter 165 µm, 250 µm, 400 µm and 900 µm Recoat diameter 195 µm, 280 µm, 450 µm, and 1000 µm Recoat length 4 to 50 mm UV curable material capacity 53 cc Recoat and proof modes 30 programmable modes Operating conditions 10 to 30 C, 0 to 90% humidity, non-condensing Storage conditions -40 to 60 C, 0 to 90% humidity, non-condensing Ordering Information DESCRIPTION FSR-02 Fiber Recoater The FSR-02 Fiber Recoater comes with ADC-10 AC Adapter, AC Cord, fiber protection cover and operation manual (mold sold separately). AFL NO. S Accessories DESCRIPTION FSR-02-MOLD-195 Mold for recoating 165 µm coated fiber FSR-02-MOLD-280 Mold for recoating 250 µm coated fiber FSR-02-MOLD-450 Mold for recoating 400 µm coated fiber FSR-02-MOLD-1000 Mold for recoating 900 µm jacketed fiber Force gauge for calibrating proof tester Force gauge mounting table (required with gauge) Spare UV lamp AFL NO. S S S S S S S , AFL, all rights reserved. PP , Revision 2,

52 *Delivered as shown CT-30 Fiber Cleaver The CT-30 Cleaver sets the standard for portability, reliability and ease of use. Available for either single fiber or ribbon splicing (up to 12 fiber ribbons) applications, the CT-30 Cleavers are compatible with all AFL fusion splicers. The improved version offers a larger base for a more stable platform, improved visibility when placing the fiber, and three scrap collection options. Designed for excellent portability, the CT-30 is equally at home in a splicing van or in a bucket truck and is ideal for FTTx applications. The 16-position blade yields 48,000 single-fiber cleaves, or 4, fiber ribbon cleaves before requiring replacement, and the built-in scrap collector conveniently stores fiber shards until they can be safely discarded. The CT-30 Cleaver is packaged with three scrap collection options that allow the user to tailor it to their cleaving preferences. The CT30 is delivered with the SC-01 Side Cover installed for users that prefer not to use an automated scrap collection system. For those that prefer an automated scrap collection system, the FC-02 Fiber Collector and two scrap box options are included. The FDB-02 Scrap Box is a smaller bin for users seeking a compact profile. The FDB-03 Scrap Box is a larger bin with sweeping brush and static resistant surfaces for those users seeking to maximize scrap capacity. All scrap options are easily configured by the user. Specifications PARAMETER VALUE Applicable Fiber Conventional silica optical fiber Fiber Count Single and up to 12 fiber ribbon Coating Diameter 250 μm to 900 μm Cladding Diameter 125 μm Cleave Angle Capability typically <0.5 Blade lifetime 48,000 fiber cleaves (4, fiber cleaves) Dimensions (W x D x H) 69 mm x 82 mm x 41 mm (2.7" x 3.2" x 1.6") Weight 180 g (0.4 lbs) Ordering Information Shown in CC-21 Carrying Case DESCRIPTION APPLICATION FIBER HANDLING SYSTEM CLEAVE LENGTH AFL NO. CT-30 Fiber Ribbons Fiber Holders for the following: 10 mm S (up to 12 fibers) FH-XXX, FH-50-XXX or FH-60-XXX versions CT-30A Single Fibers: µm coating, 125 µm cladding AD-30A Adapter Plate 900 µm: mm 250 µm: 6-20 mm S Included with Cleaver: AD-30A Adapter Plate (CT30A only) FC-02 Fiber Collector FDB-02 Scrap Box (small) FDB-03 Scrap Box (large) SC-01 Side Cover (installed) CC-21 Carrying Case Hex Wrench (1.5 mm) Instruction Manual Accessories DESCRIPTION Replacement Blade for CT-30 Series Cleavers FC-02 Fiber Collector AD-30A Adapter Plate AD-30B Adapter Plate (Fixed 16 mm cleave length) AD-30C Adapter Plate for 2 & 3mm Cord FDB-02 Fiber Collector Scrap Box FDB-03 Large Fiber Collector Scrap Box SC-01 Side Cover HBA-01 Fiber Holder Base Attachment CC-21 Carrying Case for CT-30 Series Cleaver AFL NO. S S S S S S S S S S , AFL, all rights reserved. PP , Revision 3,

53 CT-100 Fiber Cleaver Precise cleaving is required for photonic splicing applications as the types of optical fiber become more diversified to meet new applications. In addition, angled cleaving is often required for low back-reflection fiber end preparation. The CT-100 has been developed to offer adjustability and versatility for these various fiber types and applications while offering superior cleaving performance beyond conventional cleavers that utilize a circular blade. The CT-100 is equipped with a motorized diamond blade that touches the fiber after tension has been applied providing high-strength cleaving capability. Features Diamond blade with long blade life Large diameter fiber cleaving capability (fiber diameter range 80 to 250 µm) Angle cleaving capability (0 to 15 degrees) Cleave counter Adjustable cleave length Dual power sources (4 AA batteries or AC adapter) Specifications PARAMETER Applicable Fiber Cleaving Performance VALUE Conventional silica optical fiber Typical 0.5 degrees Cladding Diameter 80 to 250 µm Coating Diameter 160 to 2000 µm Cleave Angle Capability Cleave Length Dimensions Weight Blade Lifetime DC Power Supply AC Power Supply Operating Conditions Storage Conditions 0 to 15 degrees (adjustable) 0 to 40 with Fiber Holder, FH-100 series or FH-40 series 140 mm (W) x 110 mm (D) x 95 mm (H) 900 g or less (excluding batteries) 20,000 fibers (1,000 fibers x 20 positions) 4 AA size batteries (approx cleaves) 100 to 240 VAC / 50 to 60 Hz using ADC-16 Temperature: 0 to 40 C, Humidity: 0 to 95% RH (Non-condensing) Temperature: -40 to 80 C, Humidity: 0 to 95% RH (Non-condensing) Ordering Information DESCRIPTION CT-100 Advance Optical Fiber Cleaver Includes: ADC-16 AC adapter, ACC-09 AC power cord, 1.5 mm hex wrench, 2.5 mm hex wrench and instruction manual AFL NO. S Accessories DESCRIPTION ADC-16 AC Adapter ACC-09 AC Power Cord CB-03 Cleaver Blade AFL NO. S S S , AFL, all rights reserved. PP , Revision 3,

54 photo PowerCleave To complement the line of world class splicing systems, AFL s PowerCleave combines the precision of an ultrasonic cleaver with the ease and improved fiber management of the Fujikura fiber holder system. The PowerCleave utilizes the tensile stress method to avoid touching or damaging the bare glass surface during cleaving, ensuring highly robust, reliable and durable splice results. The PowerCleave provides consistent flat ends even at cleave lengths as short as 3 mm. Specially designed for use with Fujikura s specialty market splicers, this advanced cleaving system allows for more reliability and greater splicing consistency with less dependence on operator technique. Features Tensile cleaving with ultrasonic blade Consistent, low-angle cleaves of short cleave-length fibers Fiber holder system reduces fiber handling Clean, reliable quality Specifications PARAMETER Fibers Cleaved Minimum Cleave Length Cleave Angle Blade Clamping System Case Battery Dimensions (L x W x D) Weight Operating Temperature Storage Temperature CE Conformity VALUE 80 µm µm (cladding diameter) 3 mm <0.6 typical (95% of cleaves) Diamond with an estimated life of over 20,000 cleaves Compatible with Fujikura specialty market fiber holder systems ABS impact resistant with non-slip feet and a 6.25 mm (.24 inch) BSW thread tripod mount for hard mounting to a workstation 9V alkaline (MN 1604), battery life approximately 10,000 cleaves 75 mm x 153 mm x 150 mm (3.0 x 6.0 x 5.9 inches) 1.1 kg (2.4 lbs) 0 C to 45 C (32 F to 113 F) -20 C to 60 C (-4 F to 140 F) Fully complies with all EC equipment guidelines according to the CE declaration of conformity Ordering Information DESCRIPTION PowerCleave Kit Includes: PowerCleave, Instruction manual, 2.5 mm x 60 mm screwdriver, 2 mm Allen wrench AFL NO. S , AFL, all rights reserved. PP , Revision 3,

55 USC-03 Ultrasonic Cleaner The Fujikura ultrasonic cleaner model USC-03 provides a simple and cost effective method for cleaning optical fibers when high strength fusion splices are required. This ultrasonic cleaner readily accepts all FH-40-XXX, FH-50-XXX, FH-60-XXX and FH-100-XXX series fiber holders. The Universal Fiber Holder Adapter, available as an optional accessory, enables the use of FH-XXX series fiber holders. The high frequency ultrasonic action cleans debris and coating residue without damaging the exposed cladding and a built-in timer ensures that the required cleaning time is consistently used for all fibers processed. This cleaner, when used in conjunction with high strength stripping and cleaving accessories, produces outstanding results for the most demanding high strength applications. Features Built-in timer assures correct cleaning time Adjustable high intensity vibratory cleaning action Adjustment knob allows fine-tuning of fiber submersion depth Alcohol bath lid prevents cleaning fluid evaporation when machine is idle Specifications Included Accessories PARAMETER Applicable Fibers Applicable Fiber Holders Recommended Fluid Tank Capacity Ultrasonic Frequency Fiber Cleaning Length Output Power Timer Range Power Requirement Operating Environment Storage Environment Dimensions (W x D x H) Weight VALUE Single optical fiber FH-40, 50, 60 and 100 series Ethyl-alcohol 24 cc to 45 cc 50 khz 54 mm (max), adjustable 10 W (max) 1 to 99 seconds AC 100 to 240 V / 50 Hz to 60 Hz 0oC to 40oC, 0 to 95% RH, non-condensing -20 C to 60 C, non-condensing humidity 95 x 190 x 157 (mm) / 3.74 x 7.48 x 6.18 (inches) 1 kg / 2.2 lbs Ordering Information DESCRIPTION USC-03 Universal Fiber Holder Adapter ADC-10 Power Adapter ACC-09 Power Cord AFL NO. S S S S , AFL, all rights reserved. PP , Revision 3,

56 AFL PowerStrip AFL PowerStrip is a thermal stripper used in high strength splicing. Using the proven blade and centering design of the Schleuniger FiberStrip 7030 in addition to the fiber holder system, the AFL PowerStrip automatically centers the fiber, heats the buffer or coating and strips the buffer at a controlled rate with perfect alignment. The fiber holder system reduces fiber handling, making this tool ideal for any production environment. Features 250 µm and 900 µm fiber capability Short cycle time Lightweight and portable Specifications PARAMETER Fibers Stripped - Single Buffered Fiber Clamping System Stripping Length Heater Temperature Range Heating Time Cycle Time Power Supply Dimensions (L x W x D) Weight CE Conformity VALUE Cladding diameter: 125 µm standard, 80 µm optional Coating diameter: 250 µm and 900 µm standard, 160 µm and 400 µm optional Fujikura fiber holder clamp; compatible with FSM-45F/PM and 100 series fiber holders Up to 35 mm 110 C to 150 C (230 F to 302 F) 1.5 to 13 seconds Approximately 5 seconds/cycle (after heating) Input: 100 to 240 V AC, 50/60 ± 3 Hz; Output: 12 V DC, 12 W, 1 A 209 mm x 57 mm x 45 mm (8.25 x 2.25 x 1.8 inches) 0.7 kg (1.5 lbs) Complies with all CE equipment guidelines Ordering Information DESCRIPTION AFL PowerStrip Kit Carrying case, fiber holder clamping system, blades and centralizers for 125/250 µm and 125/900 µm fiber, power supply 230 V AC or 100/120 V AC, power cord 2 m (6.5 feet), cleaning brush and tool set (hex keys, adjustment screwdriver) Coating Blades AFL NO. S /125 µm S /160 µm S /250 µm S /400 µm S /500 µm S /900 µm S /360 µm S /500 µm S /400 µm S /900 µm S /450 µm S /600 µm S /800 µm S /1400 µm S Centralizers 125 µm S µm S µm S µm S µm S µm S µm S µm S µm S µm S µm S Power Supply 12 V DC W/PLUG ADPT S * Custom blades and centralizers available on request , AFL, all rights reserved. PP , Revision 4,

57 PCS-100 Polyimide Coating Stripper Polyimide coated optical fiber are now widely used in the oil and gas and medical industries. The polyimide coating has superior heat and chemical resistance to conventional UV curable coating material, but the coating requires additional care to remove. Dangerous chemical stripping using hot sulfuric acid or burning the coating off are common methods to strip the fiber due to the thin coating and strong coating adhesion to the fiber cladding. AFL s PCS-100 Polyimide Fiber Coating Stripper is the first tool that uses a mechanical stripping method, providing a safe, consistent and quick stripping solution. Features Quick stripping A razorblade is applied to the fiber with specific tension and the coating is precisely planed along the fiber automatically. The process requires less time than the conventional methods of acid or heat. For a 125 µm fiber, 4 stripping passes at 90º rotational positions are typically required, and complete stripping is accomplished within 25 seconds. Larger fiber sizes require more stripping passes (at smaller rotational angle increments). Safe, high quality stripping Because hot acid is not used, the operation is much safer. In addition, the fiber quality degradation is kept at a minimum as the glass surface is not damaged by oxidization of the coating during burning or arcing. Flexible Many parameters, such as the razor blade position and stroke, and fiber rotation angle are all adjustable for various fiber sizes and coating materials. Specifications STRIPPING PERFORMANCE Applicable Fiber Silica based Single-mode and Multimode glass fiber Applicable Coating Polyimide coating and UV curable resin coating Cladding Diameter Range 60 to 1200 μm Coating Diameter Range 60 to 1,500 μm Fiber Clamping Adaptable to range of fiber/coating sizes by selection of applicable pair of FH-100-XXX series fiber holders Strip Length 1 to 35 mm Stripping Time 4 stripping passes: 20 seconds 8 stripping passes: 35 seconds 12 stripping passes: 50 seconds Blade Life 350 fibers / blade (In the case of 4 strips per fiber) Stripping Modes 30 user-programmable modes Proof Modes 30 user-programmable modes PROOF TEST FUNCTION Maximum Proof Test Force 2 kgf Typical Proof Test Cycle Time 3 seconds DIMENSIONAL DATA Dimensions 230 mm (W) x 214 mm (D) x 151 mm (H) Weight 5.0 kg excluding AC adapter POWER SOURCE Power Input AC100 to 240 V (50 Hz to 60 Hz) OPERATION AND STORAGE CONDITIONS Operating Conditions Temperature: 0 to 40 C, Humidity: 0 to 95% RH (Non-condensing) Storage Conditions Temperature: -40 to 80 C, Humidity: 0 to 95% RH (Non-condensing) Ordering Information DESCRIPTION PCS-100 Polyimide Coating Stripper (Includes: FH , ADC-15 AC Adapter, ACC-02, Instruction manual and PCB-01 replacement blades.) AFL NO. S Accessories DESCRIPTION FH ADC-15 ACC-02 PCB-01 (Box of 50) AFL NO. S S S S , AFL, all rights reserved. PP , Revision 1,

58 Splice Protection Sleeves AFL offers a wide selection of fiber protection sleeves to meet any application. The FP series is the industry standard for durable and lasting protection of single fiber splices in field installations, while the FP-04(T) and FP-05 provide the same durable protection for 8 and 12 fiber ribbon respectively. The FPS01 and FPS04 series are specially designed for optical components, where small packaging is a priority. These micro sleeves provide the known reliability of Fujikura sleeves in the smallest possible lengths. This easy and cost effective method is a great alternative to recoating. The FPS01 and FPS04 series offer a wide range of options to accommodate various coating sizes, and are manufactured in a variety of lengths. This gives great flexibility in designing optical modules. Standard Sleeves: Dimensions & Applicable Fiber SLEEVES FOR SINGLE FIBERS UP TO 900 MICRONS DESCRIPTION SLEEVE LENGTH FIBER CLEAVE LENGTH SLEEVE DIAMETER AFTER SHRINK PACKAGING AFL NO. FP mm 16 mm 3.1 mm (max.) 1000 Box/100 Pack S FP mm 10 mm 3.1 mm (max.) 1000 Box/100 Pack S SLEEVES FOR TFOCA CABLE (DUAL 900 μm) DESCRIPTION FIBER COUNT SLEEVE LENGTH FIBER CLEAVE LENGTH SLEEVE DIAMETER AFTER SHRINK PACKAGING AFL NO. FP-D mm 10 mm 3.6 mm (max.) 1000 Box & 50 Pack S SLEEVES FOR RIBBON FIBERS DESCRIPTION FIBER COUNT SLEEVE LENGTH FIBER CLEAVE LENGTH SLEEVE DIAMETER AFTER SHRINK PACKAGING AFL NO. FP-04(T) Up to 8 fibers 40 mm 10 mm 4.1 mm (max.) 250 Box/25 Pack S FP-05 Up to 12 fibers 40 mm 10 mm 4.5 mm (max.) 250 Box/5 Pack S FP Up to 12 fibers 28 mm 10 mm 4.5 mm (max.) 250 Box/25 Pack S FPS04-30 Up to 4 fibers 30 mm 10 mm 2.4 mm (max.) 1,000 Box/25 Pack S FPS08-28 Up to 8 fibers 28 mm 10 mm 3.4 mm (max.) 500 Box/25 Pack S FPS24-40 Up to 24 fibers 40 mm 10 mm 8 mm (max.) 200 Box/5 Pack S Specifications PARAMETER DESCRIPTION VALUE Outer tube FP-60/40/03 series FP-04(T) / FP-05 Polyethylene Inner tube Ethylene-Vinyl Acetate (Polyolefin Copolymer) Strength member Operation condition (after shrink) Storage condition (before shrink) FP-60/40/03 series FP-04(T) / FP-05 Stainless steel Quartz glass -40 to 75 C, 0 to 95% RH (Non dew) -40 to 60 C, Non dew FP-03 series FPS01 series FP-40 series FP-60 series FP-04(T)/05 FPS04-30 FPS , AFL, all rights reserved. PP , Revision 6,

59 Splice Protection Sleeves Micro Sleeves: Dimensions & Applicable Fiber FPS SERIES FOR SINGLE FIBERS UP TO 400 MICRON FIBER DESCRIPTION SLEEVE LENGTH FIBER CLEAVE LENGTH SLEEVE DIAMETER AFTER SHRINK PACKAGING AFL NO. FPS mm 4 mm 1.5 mm 50 Pack S FPS mm 4 mm 1.5 mm 50 Pack S FPS mm 8 mm 1.5 mm 50 Pack S FPS mm 10 mm 1.5 mm 50 Pack S FPS mm 15 mm 1.5 mm 50 Pack S FPS mm 16 mm 1.5 mm 1,250 Box S FPS SERIES FOR SINGLE FIBERS UP TO 900 MICRON FIBER DESCRIPTION SLEEVE LENGTH FIBER CLEAVE LENGTH SLEEVE DIAMETER AFTER SHRINK PACKAGING AFL NO. FPS mm 4 mm 2.3 mm 50 Pack S FPS mm 6 mm 2.3 mm 50 Pack S FPS mm 6 mm 2.3 mm 50 Pack S FPS mm 13 mm 2.3 mm 50 Pack S FPS mm 16 mm 2.3 mm 50 Pack S Specifications PARAMETER MODEL VALUE Outer tube FPS01 series / FPS04-30 Polyethylene Inner tube Strength member Operation condition (after shrink) Storage condition (before shrink) FPS01 series FPS04-30 / FPS08-28 Ethylene-Vinyl Acetate (Polyolefin Copolymer) Stainless steel Quartz glass -40 to 75 C, 0 to 95% RH (Non dew) -40 to 60 C, Non dew Type Variations FULL SCALE , AFL, all rights reserved. PP , Revision 6,

60 LightGuard 55 Sealed Fiber Optic Splice Closure Designed with versatility in mind, the LightGuard (LG) 55 sealed closure from AFL offers a variety of solutions including repair and distribution splicing, grounding for Fiber-in-the-Loop applications, and for use as an isolation gap with armored cables. This closure accepts stranded loose tube or ribbon fiber cables in either armored or dielectric configurations and can be utilized in a butt or in-line configuration. The LG-55 closure incorporates a unique cable clamp design sealing the cable, allowing both of the cover halves to be removed without disturbing the contents. In addition, AFL s Peel & Seal Grommet System is incorporated to ensure a tight fit on various cable diameters, fully sealing the closure and protecting the fiber while eliminating cumbersome tape and washers making installation fast and easy. Features Accommodates cables to 0.70" O.D. for splicing and grounding/bonding Incorporates the Peel and Seal Grommet System, fully sealing the closure Includes removable, integral central splicing module and individual cable retention clamps Requires only a common can wrench for installation Specifications PARAMETER VALUE Splice Capacity (Max.) Single, Mass, Mechanical 24, n/a, 24 Number of Splice Trays (Max.) Single, Mass, Mechanical* 1, n/a, 1 Cable Entrance Configuration Butt or In-line Cable Sizes (Min. O.D. - Max. O.D.) Included Grommets Single in. (mm) Double Express Port Only in. (mm) (2) Express Ports 0.40" " ( ) 0.26" " ( ) Additional Grommets Quad Express Port Only in. (mm) 0.26" " ( ) Dimensions (L x D) in. (mm) 14.0" x 4.0" (343.0 x 101.6) Weight lbs. (kg) 3.0 (1.36) Ordering Information In-line Repair Closure (IRC) for repair of flat or round drop cables DESCRIPTION MODEL NO. AFL NO. LG-55 FC PS Fiber Optic Splice Closure Stores up to 32 single LG55-U-1 FC PS fusion, includes 2 single cable grommets and 1 dual cable grommet kit for sealing/retention and 2 ground terminals. Splice tray and hanger brackets included. Not included: Cable Grounding Kits LL-2425 Single Splice Tray Stores (32) single fusion splices. LL-2425 FC Maximum of 1 trays in the LG55. Tray Included. LG-350 Single Grommet Kit (Min. 0.40" - Max. 1.00") LG-350 Exp FC For use in LG-55 on Express Port side. Single Kit LG-350 Dual Grommet Kit (Min. 0.26" - Max. 0.44") For use in LG-55 on Express Port side. LG-350 Exp Dual Kit FC LG-350 Quad Grommet Kit (Min. 0.26" - Max. 0.38") LG-350 Exp Quad Kit FC For use in LG-55 on Express Port side. LG-55 Grommet Kit (1) 3 flat drop grommet (flat drop 0.31" or round LG-55 Drop Kit FC cable up to 0.25") and (1) dual grommet (Min. 0.26" - Max. 0.44"). Cable Grounding Kit (pack of 5) Clamp-On Ground Cable Only CGK-5 FC *Mechanical Splice Kit. Includes 10 pieces of VHB tape. Used in all splice trays. Each piece holds 12 splices. VHB Tape FA , AFL, all rights reserved. PP , Revision 9,

61 LightLink 500 Optical Splicing and Distribution Enclosure The LightLink (LL) 500 Optic Splicing and Distribution Enclosure provides for organizing, splicing and interconnecting fibers in broadband, distribution and building entrance applications. The enclosure features a scratch and corrosion resistant powder paint coating base and a fully gasketed hinged cover. A unique self-sizing grommet design allows for express and pre-terminated cable installation. The LL-500 supports up to five LL-2450 splice trays for up to 60 single fusion splices or three LL-4850 splice trays (not included in base unit) and an optional 12 fiber, hinged Interconnect Module. LL-500 with interconnect kit installed Features NEMA 3 rated enclosure Independent cable strain relief system Cable entry/exit grommet seals Fiber routing system Splice tray support system Hinged cover Specifications Supports optional Interconnect Modules Interconnect Module supports up to 12 SC bulkhead adapters Secured with a standard padlock 4 cable ports with standard grommets 8 cable ports with optional expansion kits PARAMETER VALUE Material Steel Coatings Electrostatically applied, powder coat Color Antique white Cable Ports 4-8 Cable Sizes (Max. O.D. Min. O.D.) " LL-500 with LL-2450 splice tray installed Up to 8 with Dual Grommet Kits " " Dimensions (H x W x D) in. (cm) 17.5 x 9.0 x 4.0 (44.45 x x 10.16) Weight lbs. (kg) 6.5 (2.95) Ordering Information DESCRIPTION AFL NO. LL-500-U-0 FM LL-500 Interconnect Kit with SC UPC adapters FM LL-500 Interconnect Kit with SC APC adapters FM LL-500 Interconnect Kit without adapters FM LL-500 with Multi-port Grommets FM LL-2450 Single Fusion Splice Tray (stores 12 single fusion splices) LL-4850 Mass Fusion Splice Tray (stores 8 mass fusion sleeves - 96 fibers) LL-500 Multi-port Grommet Kit, 6 drop cable entry up to 0.37 OD FC , AFL, all rights reserved. PP , Revision 3,

62 LightLink Optical Entrance Enclosures The Optical Entrance Enclosures (OEE) are designed to provide a convenient splicing and interconnection location for outside plant cabling entering a Central Office (CO), Controlled Environmental Vault (CEV) or customer location. Each unit is designed to allow the entrance and management of up to 60 cables for splicing and interconnecting. Cables from termination locations and the outside plant are easily installed and managed. Access to individual fiber splices and fiber bundles are made easy by splice tray and fiber management designs. Features Manages multiple cable enter and exit facilities Each splice tray handles up to 48 single fusion or 144 mass fusion splices Enclosures for indoor or outdoor NEMA 3 applications Internal ground bar and pass through ground lugs Rated NEMA Type 3 OEE-288/576 Optical Entrance Enclosures Specifications PARAMETER Material Coatings Color Dimensions VALUE Aluminum or steel Electrostatically applied, powder coat Granite See Detail Drawings * Fiber splice trays sold separately Accessories - Shingle Kits OEE-720/1440 Optical Entrance Enclosures , AFL, all rights reserved. PP , Revision 4,

63 LightLink Optical Entrance Enclosures Ordering Information DESCRIPTION MODEL NO. AFL NO. OPTICAL ENTRANCE ENCLOSURE OEE-288/ Single Fusion or 1728 Mass Fused Splice Capacity, up to 60 Cable Entry Ports Includes: (2) 6-Port Standard Shingles (Each port Accepts a " Cable) (1) 5-Port Shingles (2 Port Accepts a " Cable, and 3 small Ports Accepting a Cable ") (4) Medium Sealing and Retention Kits (each supporting a " Cable) (1) Large Sealing and Retention Kit (Each Supporting a " Cable) (3) Metallic Cable Bonding Kits (1) Wall-Mount Hardware (1) OEE Locking Key OPTICAL ENTRANCE ENCLOSURE 720 Single Fusion or 4320 Mass Fused Splice Capacity, up to 60 Cable Entry Ports Includes: (2) 6-Port Standard Shingles (Each port Accepts a " Cable) (1) 5-Port Shingles (2 Port Accepts a " Cable, and 3 small Ports Accepting a Cable ") (4) Medium Sealing and Retention Kits (each supporting a " Cable) (1) Large Sealing and Retention Kit (Each Supporting a " Cable) (3) Metallic Cable Bonding Kits (1) Wall-Mount Hardware (1) OEE Locking Key OEE-720/ OEE 288/576 OEE 720/ , AFL, all rights reserved. PP , Revision 4,

64 LightLink Optical Entrance Enclosures Accessories DESCRIPTION MODEL NO. AFL NO. OEE Fiber Splice Tray STF Metallic Cable Bonding Kit MBK Work Shelf OEE-WS Cable Retention and Sealing Kit Small (Accepts " O.D. Cable) CRSK Cable Retention and Sealing Kit Medium (Accepts " O.D. Cable, four included with OEE) CRSK Cable Retention and Sealing Kit Large (Accepts " O.D. Cable, one included with OEE) CRSK Cable Retention and Sealing Kit XLarge (Accepts " O.D. Cable) CRSK Cable Retention and Sealing Kit XXLarge (Accepts " O.D. Cable) CRSK Shingle Kit Standard, 6-Ports (Accepts Six Cables From " O.D., two included with OEE) SK-STD Shingle Kit Standard, 5-Ports SK-LS (2) Large ( " O.D. Cable Ports) (3) Small ( " O.D. Cable Ports) (One Included with OEE) Shingle Kit, Two X-Large, (2) Cable Ports ( " O.D.) SK-XL Shingle Kit, Two XX-Large, (2) Cable Ports ( " O.D.) SK-XXL Cable Bonding Kit Cable Retention and Sealing Kit Work Shelf , AFL, all rights reserved. PP , Revision 4,

65 LightLink Fiber Optic Splice Trays AFL s LightLink series of Fiber Optic Splice Trays offers a variety of unique and flexible splice and storage possibilities. They are available in industry standard config urations (single, mass). Features In-line or butt splice capability (see model descriptions) Pre-formed radiuses maintain bend requirements Interlocking base and cover provides tray stability without the use of a bolt Extended finger guides easily store and route loose fiber or ribbon Ordering Information Splice Trays for Sealed Fiber Optic Splice Closures DESCRIPTION MODEL NO. AFL NO. LG-55-U LG-150-U LG-250-U LG-350-U LG WTC LG WTC Single Fuse: 32 LL-2425 FC Max trays: 1 N/A N/A N/A N/A N/A Mass Fuse: N/A Single: " (L) x 2.730" (W) x 0.829" (H) Mass: N/A Single Fuse: 12 Mass Fuse: N/A 7.139" (L) x 4.294" (W) x 0.370" (H) LL N/A Max Trays: 4 Single: 48 Mass: N/A N/A N/A N/A N/A Single Fuse: N/A Mass Fuse: 8 (96 fiber) 7.139" (L) x 4.294" (W) x 0.370" (H) LL N/A Max Trays: 4 Single: N/A Mass: 32 (384 fiber) N/A N/A N/A N/A Single Fuse: 12 Mass Fuse: 8 (96 fiber) 7.139" (L) x 4.294" (W) x 0.370" (H) LL N/A Max Trays: 4 Single: 48 Mass: 48 (384 fiber) N/A N/A N/A N/A Single Fuse: 24 Mass Fuse: N/A " (L) x 4.042" (W) x 0.390" (H) LL N/A N/A Max Trays: 5 Single: 120 Mass: N/A Max Trays: 13 Single: 312 Mass: N/A N/A N/A , AFL, all rights reserved. PP , Revision 9,

66 LightLink Fiber Optic Splice Trays (cont.) Ordering Information Splice Trays for Sealed Fiber Optic Splice Closures DESCRIPTION MODEL NO. AFL NO. LG-250-U LG-350-U LG-350-AC LG-350XL-U LG WTC LG WTC Single Fuse: 60 Mass Fuse: 12 (144 fiber) " (L) x 5.125" (W) x 0.485" (H) LL-7644 FA N/A Max Trays: 6 Single: 360 Mass: 72 (864 fiber) N/A N/A N/A Max Trays: 3 Single: 180 Mass: 72 (864 fiber) * Note: Contains enough splice holders for 24 mass splices (288 fibers) when using AFL Wrapping Tube Cable. Single Fuse: 24 Mass Fuse: 4 (48 fiber) " (L) x 4.270" (W) x 0.531" (H) LL Max Trays: 3 Single: 72 Mass: 12 (144 fiber) Mechanical: 36 Max Trays: 8 Single: 192 Mass: 32 (384 fiber) Mechanical: 96 N/A N/A N/A N/A Single Fuse: 48 Mass Fuse: N/A " (L) x 4.270" (W) x 0.531" (H) LL S FA Max Trays: 3 Single: 144 Mass: N/A Max Trays: 8 Single: 384 Mass: N/A N/A N/A N/A N/A Single Fuse: N/A Mass Fuse: 12 (144 fiber) " (L) x 4.270" (W) x 0.531" (H) LL Max Trays: 3 Single: N/A Mass: 36 (432 fiber) Max Trays: 8 Single: N/A Mass: 96 (1152 fiber) N/A N/A N/A N/A Single Fuse: 96 Mass Fuse: 24 (288 fiber) " (L) x 4.875" (W) x 0.485" (H) LL N/A Max Trays: 5 Single: 480 Mass: 120 (1440 fiber) N/A Max Trays: 9 Single: 864 Mass: 216 (2592 fiber) N/A N/A Single Fuse: 60 Mass Fuse: N/A " (L) x 5.125" (W) x 0.485" (H) LL-7060 FA N/A Max Trays: 6 Single: 360 Mass: N/A N/A N/A N/A Max Trays: 3 Single: 180 Mass: N/A , AFL, all rights reserved. PP , Revision 9,

67 LightLink Fiber Optic Splice Trays (cont.) Ordering Information Splice Trays for LG-350 and LG-350XL-U Sealed Fiber Optic Splice Closures DESCRIPTION MODEL NO. AFL NO. LG-350-U LG-350-AC LG-350XL-U LG WTC LG WTC Single Fuse: N/A Mass Fuse: 12 (144 fiber) " (L) x 5.125" (W) x 0.485" (H) LL-7144 FA Max Trays: 6 Single: 360 Mass: 72 (864 fiber) N/A N/A N/A Max Trays: 3 Single: 180 Mass: 72 (864 fiber) Single Fuse: 36 Mass Fuse: 12 (144 fiber) 8.125" (L) x 4.875" (W) x 0.485" (H) LL-4808L-R FA N/A Max Trays: 4 Single: 144 Mass: 48 (576 fiber) N/A Max Trays: 4 Single: 144 Mass: 48 (576 fiber) N/A Single Fuse: N/A Mass Fuse: 12 (144 fiber) 8.125" (L) x 4.875" (W) x 0.485" (H) LL-4808 R FA N/A Max Trays: 4 Single: N/A Mass: 48 (576 fiber) N/A Max Trays: 4 Single: N/A Mass: 48 (576 fiber) N/A Single Fuse: 36 Mass Fuse: N/A 8.125" (L) x 4.875" (W) x 0.485" (H) LL-4808 L FA N/A Max Trays: 4 Single: 144 Mass: N/A N/A Max Trays: 4 Single: 144 Mass: N/A N/A Single Fuse: N/A Mass Fuse: 24 (288 fiber) " (L) x 4.875" (W) x 0.485" (H) LL-4896 R FA Max Trays: 5 Single: N/A Mass: 120 (1440 fiber) N/A Max Trays: 9 Single: N/A Mass: 216 (2592 fiber) N/A N/A Single Fuse: 96 Mass Fuse: N/A " (L) x 4.875" (W) x 0.485" (H) LL-4896 L FA Max Trays: 5 Single: 480 Mass: N/A N/A Max Trays: 9 Single: 864 Mass: N/A N/A Max Trays: 3 Single: 180 Mass: N/A , AFL, all rights reserved. PP , Revision 9,

68 LightLink Fiber Optic Splice Trays (cont.) Ordering Information Splice Trays for Aerial Weathertight Fiber Optic Splice Closures DESCRIPTION MODEL NO. AFL NO. LG-410-U LG-420-U FTTx LG-500-U LG-500-U FTTx Single Fuse: 24 Mass Fuse: N/A " (L) x 4.042" (W) x 0.390" (H) LL Max Trays: 4 Single: 96 Mass: N/A N/A Max Trays: 4 Single: 96 Mass: N/A N/A Single Fuse: 32 Mass Fuse: N/A 6.300" (L) x 2.730" (W) x 0.829" (H) LL-2425 FC N/A Max Trays: 1 Single: 32 Mass: N/A N/A Max Trays: 1 Single: 32 Mass: N/A Single Fuse: 24 Mass Fuse: 4 (48 fiber) " (L) x 4.270" (W) x 0.531" (H) LL Max Trays: 3 Single: 72 Mass: 12 (144 fiber) Mechanical: 36 N/A Max Trays: 3 Single: 72 Mass: 12 (144 fiber) Mechanical: 36 N/A Single Fuse: 12 Mass Fuse: N/A 7.139" (L) x 4.294" (W) x 0.370" (H) LL N/A N/A N/A N/A Single Fuse: N/A Mass Fuse: 12 (144 fiber) " (L) x 4.270" (W) x 0.531" (H) LL Max Trays: 3 Single: N/A Mass: 36 (432 fiber) N/A Max Trays: 3 Single: N/A Mass: 36 (432 fiber) N/A Single Fuse: N/A Mass Fuse: 8 (96 fiber) 7.139" (L) x 4.294" (W) x 0.370" (H) LL N/A N/A N/A N/A Single Fuse: 12 Mass Fuse: 8 (96 fiber) 7.139" (L) x 4.294" (W) x 0.370" (H) LL N/A N/A N/A N/A , AFL, all rights reserved. PP , Revision 9,

69 LightLink Fiber Optic Splice Trays (cont.) Ordering Information Splice Trays for Aerial Weathertight Fiber Optic Splice Closures DESCRIPTION MODEL NO. AFL NO. LG-500-U-FTTx-ISO LG-600-U LG-600 FTTx Single Fuse: 24 LL N/A Max Trays: 12 Max Trays: 2 Mass Fuse: N/A Single: 288 Single: " (L) x 4.042" (W) x 0.390" (H) Mass: N/A Mass: N/A LG-600-U-FTTx-ISO N/A Single Fuse: 32 Mass Fuse: N/A 6.300" (L) x 2.730" (W) x 0.829" (H) LL-2425 FC N/A N/A N/A N/A Single Fuse: 24 Mass Fuse: 4 (48 fiber) " (L) x 4.270" (W) x 0.531" (H) LL N/A Max Trays: 8 Single: 192 Mass: 32 (384 fiber) Mechanical: 12 N/A N/A Single Fuse: 12 Mass Fuse: N/A 7.139" (L) x 4.294" (W) x 0.370" (H) LL Max Trays: 1 Single: 12 Mass: N/A N/A N/A Max Trays: 2 Single: 24 Mass: N/A Single Fuse: N/A Mass Fuse: 12 (144 fiber) " (L) x 4.270" (W) x 0.531" (H) LL N/A Max Trays: 8 Single: N/A Mass: 96 (1152 fiber) N/A N/A Single Fuse: N/A Mass Fuse: 8 (96 fiber) 7.139" (L) x 4.294" (W) x 0.370" (H) LL Max Trays: 1 Single: N/A Mass: 8 (96 fiber) N/A N/A Max Trays: 2 Single: N/A Mass: 16 (192 fiber) Single Fuse: 12 Mass Fuse: 8 (96) 7.139" (L) x 4.294" (W) x 0.370" (H) LL Max Trays: 1 Single: 12 Mass: 8 (96 fiber) N/A N/A Max Trays: 2 Single: 24 Mass: 16 (192 fiber) , AFL, all rights reserved. PP , Revision 9,

70 LightLink Fiber Optic Splice Trays (cont.) Ordering information Splice Trays for Aerial Weathertight Fiber Optic Splice Closures DESCRIPTION MODEL NO. AFL NO. LG-410-U LG-500-U LG-600-U Single Fuse: N/A Mass Fuse: 4 (48 fiber) " (L) x 4.270" (W) x 0.531" (H) LL Max Trays: 3 Single: N/A Mass: 12 (144 fiber) Max Trays: 3 Single: N/A Mass: 12 (144 fiber) Max Trays: 8 Single: N/A Mass: 32 (384 fiber) Ordering Information Splice Trays for Fiber Optic Enclosures DESCRIPTION MODEL NO. AFL NO. LL-400B WITH INTERCONNECT LL-400B WITHOUT INTERCONNECT Single Fuse: 24 LL Max Trays: 4 Max Trays: 6 Mass Fuse: 4 (48 fiber) Single: 96 Single: 144 Mechanical : " (L) x 4.270" (W) x 0.531" (H) Mass: 16 (192 fiber) Mass: 24 (288 fiber) Mechanical: 48 Mechanical: 72 LL-400SX WITH 2 LGX PLATES Max Trays: 3 Single: 72 Mass: 12 (144 fiber) Mechanical: 36 LL-400SX WITHOUT LGX PLATES Max Trays: 9 Single: 216 Mass: 36 (432 fiber) Mechanical: 108 Single Fuse: 48 Mass Fuse: N/A " (L) x 4.270" (W) x 0.531" (H) LL S FA Max Trays: 4 Single: 192 Mass: N/A Max Trays: 6 Single: 288 Mass: N/A Max Trays: 3 Single: 144 Mass: N/A Max Trays: 9 Single: 432 Mass: N/A Single Fuse: N/A Mass Fuse: 12 (144 fiber) " (L) x 4.270" (W) x 0.531" (H) LL Max Trays: 4 Single: N/A Mass: 48 (576 fiber) Max Trays: 6 Single: N/A Mass: 72 (864 fiber) Max Trays: 3 Single: N/A Mass: 36 (432 fiber) Max Trays: 9 Single: N/A Mass: 108 (1296 fiber) Single Fuse: N/A Mass Fuse: 4 (48 fiber) " (L) x 4.270" (W) x (H) LL Max Trays: 4 Single: N/A Mass: 16 (192 fiber) Max Trays: 6 Single: N/A Mass: 24 (288 fiber) Max Trays: 3 Single: N/A Mass: 12 (144 fiber) Max Trays: 9 Single: N/A Mass: 108 (1296 fiber) , AFL, all rights reserved. PP , Revision 9,

71 LightLink Fiber Optic Splice Trays (cont.) Ordering Information Splice Trays for Fiber Optic Enclosures DESCRIPTION MODEL NO. AFL NO. LL-500 LL-580 Single Fuse: N/A Mass Fuse: 12 (144 fiber) " (L) x 5.125" (W) 0.485" (H) LL-7144 FA N/A Max Trays: 2 Single: N/A Mass: 24 (288 fiber) Single Fuse: 60 Mass Fuse: 12 (144) " (L) x 5.125" (W) 0.485" (H) LL-7644 FA N/A Max Trays: 2 Single: 120 Mass: 24 (288 fiber) Single Fuse: 12 Mass Fuse: N/A 7.139" (L) x 4.294" (W) x 0.370" (H) LL Max Trays: 5 Single: 60 Mass: N/A N/A Single Fuse: N/A Mass Fuse: 8 (96 fiber) 7.139" (L) x 4.294" (W) x 0.370" (H) LL Max Trays: 3 Single: N/A Mass: 24 (288 fiber) N/A Single Fuse: 36 Mass Fuse: 12 (144 fiber) 8.125" (L) x 4.875" (W) x 0.485" (H) LL-4808L-R FA N/A Max Trays: 2 Single: 72 Mass: 24 (288 fiber) , AFL, all rights reserved. PP , Revision 9,

72 LightLink Fiber Optic Splice Trays (cont.) Ordering Information Splice Tray for Splicing Cabinets and Shelves DESCRIPTION MODEL NO. AFL NO. Telescoping Splice Tray - Stores up to 48 single fusion sleeves or 12 mass fusion sleeves (144 fibers). For use in the following products: LL-300, LL-288/576, LL-720/1440, OTSS-SYS1, OSS-SYS2 and OSS-SYS1. STF FTTx Splice Tray - Stores up to 2 single fusion sleeves. For use in the following products: ONT-760XL, ONT-3000 and CG-1500 DM Bare Fiber Splice Tray - Stores up 24 single fusion fibers without sleeves. For use in the following products: Any product that accepts the LL-2400 splice tray C Ordering Information Splice Tray Accessories DESCRIPTION AFL NO. 40 mm Fiber Protection Fusion Splice Sleeves, Telcordia compliant (50 pcs. per bag) S mm Fiber Protection Fusion Splice Sleeves, Telcordia compliant (50 pcs. per bag) S Single Fusion Splice Chip - 6 splices per chip. (10 pcs. per kit) FA Single Fusion Splice Chip - 12 splices per chip. (10 pcs. per kit) FC Single Fusion Splice Chip - 24 splices per chip. (10 pcs. per kit) Mass Fusion Splice Chip - 4 splices per chip. (10 pcs. per kit) FA Mechanical Fusion Splice Tape (10 pcs. per kit) FA Core Tube Cable Fiber Router for routing fiber up to 8 directions. For all central core tube sizes. FC Loose Tube or Ribbon Router for routing fiber up to 6 directions. For all Loose Tube and up to 12 fiber Ribbon. FC Dimensions LL-2448 and LL-4848 Splice Trays LL-1248, LL-2450 and LL-4850 Splice Trays LL-2400 Splice Tray LL-4896 Splice Tray LL-2425 Splice Tray OEE Splice Tray Telcordia is a registered trademark of Telcordia Technologies, Inc , AFL, all rights reserved. PP , Revision 9,

73 M310 Enterprise OTDR Designed for Enterprise Network Testing, Troubleshooting and Documentation Features Industry leading TruEvent analysis LinkMap for easy results interpretation Short dead zones provide precise testing of closely spaced events Front Panel and First Connector Check Live fiber detection Inspection ready with DFS1 Digital FiberScope Integrated Source, Power Meter and VFL Applications Enterprise network Data Center LAN/WAN Campus and military fiber networks and more Rugged, lightweight and easy to hold, the M310 has a Touch and Test user interface that makes it easy for experts and novices to test and document fiber networks accurately and quickly. TruEvent technology enables M310 to provide superior event analysis capability for user to verify and troubleshoot even the most complex fiber network. LinkMap visualizes test results for easy and quick interpretation. With dynamic range up to 38 db, and 16 hour battery run time, M310 provides complete Tier 1 insertion loss and Tier 2 OTDR testing. Using pre-set Industry ISO/TIA standards or user set Pass/Fail thresholds, technicians are alerted to installation problems and failures in easy-to-interpret event table. Pass/Fail event table and trace are displayed on the same screen for easy correlation. or (800) , (603) , AFL, all rights reserved. M Revision 1J,

74 M310 Enterprise OTDR M310 Models and Included Adapters WAVELENGTHS (nm) DYNAMIC RANGE (db) OTDR PORT ADAPTERS OPM PORT ADAPTERS AFL BASE MODEL NO /37 SC, LC SC, 2.5 & 1.25 mm Universal M /30/38/37 SC, LC, ST SC, 2.5 & 1.25 mm Universal M All M310 OTDRs include a USB flash drive, AC adapter, UCI switchable test port adapters, TRM 2.0 (Basic and Advanced License) and quick reference guide. For customer s convenience, AFL presents several kits options. For detailed contents of each kit, please see page 75. LinkMap LinkMap with Pass/Fail simplifies network troubleshooting and enables even novice users to easily and accurately troubleshoot optical networks. LinkMap presents an icon-based view of the tested network clearly identifying fiber start, end, connectors, splices and macro-bends. A LinkMap Summary provides endto-end link length, loss, loss per distance and ORL. Loss and reflectance of detected events is compared to industry-standard or user-settable pass/fail thresholds and displayed with clear pass/fail indications. Users can easily toggle between LinkMap, Trace view, and Event Table. TruEvent The M310 s TruEvent technology is the result of extensive research into the properties of fiber optic cable events and provides a new level of event detection accuracy and reliability in field test equipment. Taking full advantage of the unit s short dead zone and adding improved event accuracy, this is the best performing OTDR for enterprise and data center applications. With the push of a single button, users can be confident of obtaining accurate locations and measurements of all events, without the confusing introduction of false events. Advanced Analysis (AA) The AA option adds macro/microbend detection and bi-directional trace analysis to the M310 OTDR. Macro/Microbend Macro/Microbend detection helps technicians identify installation problems. Excessive bends or stress on fibers appear as increased attenuation at higher wavelengths. These bends or stresses are indicated on the Event Table with a special icon. Bi-directional Trace Analysis Bi-directional trace analysis, used to resolve splice loss measurement errors due to fiber mismatch, takes the measurement of the loss in both directions, then calculates a two-way average to provide a more accurate loss measurement. Testing and Inspection The M310 is easy to use (Touch and Test ) and comes standard with an integrated source, power meter, visual fault locator, and inspection capability. No surprise add-on charges for these commonly needed support functions. Wave ID Source and Power Meter Enables multi-wavelength insertion loss testing with automatic wavelength synchronization, reducing test time and eliminating setup errors. Source with Tone Generation Use with Optical Fiber Identifier to reliably distinguish in-service fibers from out-of-service fibers carrying test tone. Visual Fault Locator Visibly locate far-end of specific fiber; precisely pinpoint macrobends or breaks in splice enclosures and cabinets. Data storage and reporting Thousands of test results may be stored internally or on the supplied USB drive. Test results are transferable, via USB cable or USB drive, to a computer for viewing, printing, and analyzing with the supplied Windows compatible TRM 2.0 Basic Analysis and Documentation Software (Test Results Manager). The supplied TRM 2.0 Basic is licensed for installation on up to 5 PCs. With the Advanced Analysis standard feature, customer will also receive one copy of TRM 2.0 Advanced. or (800) , (603) , AFL, all rights reserved. M Revision 1J,

75 M310 Enterprise OTDR Specifications a OTDR MULTIMODE SINGLE-MODE Emitter Type Laser Laser Safety Class Class I FDA 21 CFR and ; IEC : Class I FDA 21 CFR and ; IEC : Center Wavelengths 850/1300 nm 1310/1550 nm Wavelength Tolerance ±20/±30 nm ±20/±30 nm Launch Condition k Controlled Launch at 850 nm k N/A Live Fiber Detection j Yes Yes Dynamic Range (SNR = 1) b 30/30 db 38/37 db Event Dead Zone c 0.8 m 0.8 m Attenuation Dead Zone d 2.5/2.7 m 3.0 m Pulse Widths 5, 10, 30, 100, 300 ns, 1 µs, 5, 10, 30, 100, 300 ns, 1, 3, 10 µs, 20 µs Range Settings 250 m to 30 km 250 m to 240 km Sampling Points Up to 120,000 Up to 120,000 Minimum Data Point Spacing e 3 cm 3 cm Group Index of Refraction (GIR) to to Distance Uncertainty/Accuracy f ±( % x distance + data point spacing) ±( % x distance + data point spacing) Linearity g ±0.05 db/db ±0.05 db/db Loss Threshold 0.02 db 0.02 db Loss Resolution 0.01 db 0.01 db Reflectance Range l, h 850 nm: -14 to -58 db (typical) 1300 nm: -14 to -63 db (typical) Reflectance Resolution 0.01 db 0.01 db Reflectance Accuracy h ±2 db ±2 db Real Time Refresh Rate i >2 Hz >2 Hz Units m, km, ft, kft, mi OTDR Modes Full Auto, Expert, Real-Time Trace File Format Bellcore GR-196 Version 1.1, Telcordia SR Issue 2 Trace File Storage Medium Internal and USB Trace File Storage Capacity >1000 internal, 1000s on USB Trace File Transfer to PC USB 1310 nm -14 to -65 db (typical) 1550 nm -14 to -65 db (typical) Notes: a. All specifications valid at 23 C ±2 C (73.4 F ±3.6 F) unless otherwise specified. b. Longest Range and Pulse Width, 3 minutes Averaging Time, normal resolution. c. Typical distance between the two points 1.5 db down each side of a reflective spike caused by a -40 db (multimode) or -45 db (single-mode) event using 10 ns pulse width. d. Typical distance from event location to point where trace is within 0.5 db of backscatter. e. Range <8 km. f. Does not include GIR uncertainty. Is based on the trace and user positioned cursors. g. Typical. h. For a non-saturated event. i. 2 km Range, 100 ns. j. Signals greater than -20 dbm MMF and -30 dbm SMF will trigger the Live Fiber Indication warning. k. Comparable to Encircled Flux loss measurement on OM4 fiber networks. l. For OM1 fiber typical Backscatter nm -68 nm -76 db and attenuation nm 2.77 nm 0.52 db. For OS1-OS2 fiber typical Backscatter nm nm -82 db and attenuation nm 0.31 nm 0.18 db. or (800) , (603) , AFL, all rights reserved. M Revision 1J,

76 M310 Enterprise OTDR Specifications a OLS (Standard) Emitter Type Laser, Class 1 (FDA 21 CFR and , and IEC : ) Center Wavelengths (nm) SM 1310/1550 ±20/30 nm; MM 850/1300 ±20/30 nm Spectral Width (FWHM) 5 nm max Internal Modulation 270 Hz, 330 Hz, 1 KHz, 2 KHz, CW Wavelength ID (Single/dual) On/Off Output Power Stability b SM < ±0.1 db, MM < ±0.2 db Output Power (CW) c -3 dbm ±1.5 db OPM (Standard) Calibrated Wavelengths Detector Type Display Range d -10 dbm Resolution Measurement Units Wavelength ID e Set Reference Data Storage Tone Detection f VFL (Standard) Emitter Type Safety Class Wavelength Output Power g 850, 1300, 1310, 1490, 1550, 1625, 1650 nm (displays up to 3 simultaneously) InGaAs 2 mm +6 to -70 dbm ±0.25 db 0.01 db db, dbm, mw Wave ID TM Yes Yes 270 Hz, 330 Hz, 1 khz, 2 khz Laser Class II FDA 21 CFR and ; IEC 825-1:1993, : nm ±20 nm 0 dbm (1 mw) GENERAL Display Type 3.5-inch transflective color, high contrast, high reflectivity (20%) for optimum indoor/outdoor viewing with touchscreen Display Resolution QVGA 240 x 320 Size (in boot) 23 x 11 x 7 cm (8.8 x 4.3 x 2.8 in) Weight <1.0 kg (< 2.0 lb) Drop Test GR-196-CORE Power Removable Li-ion or AC/DC power adapter (input V, ~1.5 A Hz) output 18 V DC/3.6 A (can test while charging, can operate on AC with battery removed) Battery Life h 16 hours Recharge Time i 4 hours Auto Shut Off 0-60 minutes Connectivity USB host/full speed 1.1 Operating Temperature -18 C to +50 C Storage Temperature -30 C to +60 C Relative Humidity 0 to 95 % RH (non-condensing) DFS1 DIGITAL FIBERSCOPE SUPPORT Field of View 400 x 300 µm Optical Resolution 4 µm Detection Capability 2 µm Notes: a. All specifications valid at 23 C ±2 C (73.4 F ±3.6 F) unless otherwise specified. b. Over 1 hour after 15 minute warmup of unit. c. Single-mode: SMF-2 fiber; Multimode: 50 um fiber d. Measurement Range: +3 to -65 dbm for 1300 to 1625 nm, and +3 to -60 dbm for 850 nm. e. Wavelength ID Range: +3 to -50 dbm for 1300 to 1625 nm, and +3 to -40 dbm for 850 nm. f. Tone Detect Range: +3 to -50 dbm 1300 to 1625 nm, and +3 to -40 dbm for 850 nm. g. Typical output power. h. Typical with new battery, per GR-196-Core Issue 2. i. Typical, from fully discharged to fully charged state, unit may be operating. or (800) , (603) , AFL, all rights reserved. M Revision 1J,

77 M310 Enterprise OTDR Ordering Information M310 NN P 01 HC O Optical Configuration (NN) 25 = 850/1300 nm MM and 1310/1550 nm SM 20 = 1310/1550 nm SM Packaging option (P) U = Unit K = Kit Hard Case option (HC) Select (HC) only if ordering hard case Additional Option blank = no additional hardware 1 = DFS1 2 = DFS1 and OLS Example: M310-20K-01-HC2 This order is for the M310 single-mode OTDR with 1310/1550 nm optical configuration. It s a kit with hard case, DFS1, and OLS. DFS1 and OLS are additional hardware. Below is the chart for your ordering convenience: INTEGRATED OPTION ADDITIONAL OPTION CASE OPTION AFL NO. a, c VFL OPM OLS DFS1 OLS HARD SOFT M310-25U-01 M310-20U-01 M310-25U-01-HC M310-20U-01-HC M310-25K-01-HC1 b M310-20K-01-HC1 b OLS4 M310-25K-01-HC2 b OLS2-Dual M310-20K-01-HC2 b Notes: a. Specify Language for OTDR Quick Reference Guide: English,Chinese Simplified, Chinese Traditional,German, French, Italian, Polish, Portuguese, Spanish, Turkish and Japanese. b. When ordering, specify DFS1 model. The DFS1 Digital FiberScope kit is available as either PC/UPC inspection kit (DFS XU model) or APC inspection kit (DFS1-004XA model). c. Specify Language for OTDR operating environment: English, Chinese (Simplified and Traditional), and Japanese. or (800) , (603) , AFL, all rights reserved. M Revision 1J,

78 M310 Enterprise OTDR Accessories, Upgrades, and Calibration Plans DESCRIPTION AFL NO. Inspection DFS1 Digital FiberScope PC/UPC inspection kit DFS-00-04XU DFS1 Digital FiberScope APC inspection kit DFS-00-04XA DFS1 Digital FiberScope kit without adapters DFS-00-04XN Fiber Rings 50/125 µm multimode, 150 m FR1-M5-150-x1-x2 a Laser Optimized, 50 µm multimode, 150 m FR1-L5-150-x1-x2 a 62.5/125 mm multimode, 150 m FR1-M6-150-x1-x2 a Single-mode, 150 m FR1-SM-150-y1-y2 a Cleaning Wet Cleaning kit for SC/FC/ST/LC connectors Dry Cleaning kit Basic Cleaning kit with carry case (includes One- FCP Clicks, FCC2 cleaning fluid, FiberWipes, Cletop SB) Basic Cleaning kit with MPO Cleaners and carry FCP case (includes One-Clicks, FCC2 cleaning fluid, FiberWipes, Cletop SB, MPO/MTP Cleaner) One-Click Cleaner SC, ST, FC (500+ cleans) MZ One-Click Cleaner LC/MU (500+ cleans) MZ One-Click Mini-100 SC, ST, FC (100+ cleans) MZ One-Click Mini-100 LC/MU (100+ cleans) MZ One-Click Cleaner Ultra 2.5 SC, ST, FC MZ (enlarged cleaning) One-Click Ultra Cleaner D-LC MZ (Duplex LC, 500 cleans x 2) MPO/MTP Cleaner (MPO-CLK-B) CS DESCRIPTION AFL NO. Reporting software add-on TRM 2.0 Basic Software TRM PR (OTDR Trace/OLTS Viewer, Batch Editor & Reports) TRM 2.0 Advanced Software TRM PR (Basic TRM plus Advanced Features & Reports) TRM 2.0 upgrade from Basic to Advanced Software TRM PR Calibration Plan (2 years Calibration plan) b M310-25K-HC2 CAL2-00-M310-25K-HC2 M310-20K-HC2 CAL2-00-M310-20K-HC2 M310-25U-01, -HC, -HC1 CAL2-00-M M310-20U-01, -HC, -HC1 CAL2-00-M Calibration and Warranty plan (2 years Calibration Plus plan) c M310-25K-HC2 CAL2-01-M310-25K-HC2 M310-20K-HC2 CAL2-01-M310-20K-HC2 M310-25U-01, -HC, -HC1 CAL2-01-M M310-20U-01, -HC, -HC1 CAL2-01-M Note: a. When ordering Fiber Rings, specify connector types (x1, x2, y1, y2). b. Prepaid Cal plans offer two annual calibrations at a discounted price, calibration expiration service and express calibration. c. Cal Plus plans offer the same services as the Cal plans with the addition of a two year extended warranty (three years total coverage). International Sales and Service Contact Information Available at or (800) , (603) , AFL, all rights reserved. M Revision 1J,

79 M710 Multifunction OTDR Test, Troubleshoot and Report Single-mode and Multimode Fiber Networks M710 Compact QUAD OTDR Features Industry leading TruEvent analysis LinkMap for easy results interpretation Dynamic range up to 44 db Automatic Pass/Fail analysis Live fiber detection Front Panel and First Connector Check Inspection capable with DFS1 Digital FiberScope Integrated power meter (OPM) and visual fault locator (VFL) Up to 13 hours battery life Large 6.5 inch full color touchscreen display Applications Test and certify campus & central office networks and Distributed Antenna Systems (DAS) fiber infrastructure Tier 1 and Tier 2 testing and certification of SM and MM networks Long Haul Network LAN/WAN M710 OTDR with DFS1 Digital FiberScope The M710 OTDR from AFL combines ease of use (Touch and Test ) and high performance in a rugged, large display package. With singlemode dynamic ranges up to 44 db and a MM/SM QUAD option, the M710 OTDR is ideal for testing and troubleshooting LAN/WAN, metro and long haul networks. Industry leading dead zones enhance the user s ability to locate and measure events. The M710 models utilize AFL s industry leading TruEvent technology to provide a new level of accuracy and reliability in event analysis. LinkMap visualizes test results for easy and quick interpretation. Touch and Test simplifies the M710 user experience, minimizes human errors and reduces training time by providing one-touch access to all OTDR test modes, OPM testing, Results Management and Job Creation menus. The M710 allows setting Pass/Fail thresholds to industry standard TIA/ISO values or user defined criteria and will automatically alert users of failing fibers. Touch and Test enables any technician to complete jobs more accurately and in less time, making it the ideal field test tool. *M710 series languages supported: English, Chinese, French, German, Italian, Polish, Portuguese, Spanish. Please specify language when ordering. or (800) , (603) , AFL, all rights reserved. M Revision 1B,

80 M710 Multifunction OTDR Specifications a OTDR MODEL SINGLE-MODE OTDR OPTIONS QUAD OTDR OPTION Emitter Type M M M M Safety Class Class I FDA 21 CFR and , IEC : Center Wavelengths 1310/1550 nm 1310/1550 nm 1310/1550/1625 nm 850/1300/1310/1550 nm Wavelength Tolerance ±25/25 nm ±25/25 nm ±25/25/10 nm ±25/25/25/25 nm Dynamic Range (SNR = 1) b 44/42 db 41/39 db 41/39/39 db 25/24/40/38 db c Event Dead Zone 0.8 m d 0.8 m d 0.8 m d 0.8 m d Attenuation Dead Zone 4 m e 4 m e 4 m e 4 m e Pulse Widths 5, 10, 30, 100, 300 ns; 1, 3, 10, 20 µs Laser MM SM 5, 10, 30, 100, 300 ns; 1 µs 5, 10, 30, 100, 300 ns; 1, 3, 10, 20 µs Range Settings 250 m to 256 km MM 250 m to 64 km SM 250 m to 256 km Sampling Points Max. 64,000 points Minimum Data Point Spacing m Group Index of Refraction (GIR) to Distance Uncertainty (m) f ±( % x distance + data point spacing) Linearity g ±0.03 db/db ±0.05 db/db ±0.05 db/db ±0.05 db/db Loss Threshold 0.05 db Loss Resolution 0.01 db Reflectance Accuracy h ±2 db Trace File Format SR-4731 (GR-196-CORE Appendix A & B and SR-4731) Trace File Storage Media Internal flash memory USB flash drive (2 USB host ports) Downloadable from OTDR directly to PC Trace File Storage Capacity Internal 1000 fibers Data Transfer to PC USB OTDR Modes Full Auto, Real Time, Expert Tool Free Adapters SC/ST/FC/LC Notes: a. All specifications valid at 23 C ±2 C (73.4 F ±3.6 F) unless otherwise specified. b. Longest Range and Pulse Width, 3 minutes Averaging Time, Filter on, Typical. c µm fiber for multimode test. d. Typical distance between the two points 1.5 db down each side of an unsaturated event with reflection <-45 db for SM and <-40 db for MM using a 5 ns pulse width. e. Typical distance from event location to point where trace is within 0.5 db of backscatter caused by an unsaturated event with reflection <-45 db for SM and <-40 db for MM using a 5 ns pulse width. f. Does not include GIR uncertainty. g. Typical. h. For a non-saturated event. or (800) , (603) , AFL, all rights reserved. M Revision 1B,

81 M710 Multifunction OTDR Specifications a POWER METER SINGLE-MODE OTDR OPTIONS QUAD OTDR OPTIONS M M M M Calibrated Wavelengths 850, 980, 1300, 1310, 1490, 1550, 1625 nm (displays up to 3 simultaneously) 850, 1300, 1310, 1490, 1550, 1625 nm (displays up to 3 simultaneously) Detector Type Filtered InGaAs detector InGaAs 2 mm Measurement Range (dbm) +26 to -50 dbm +3 to -70 dbm Accuracy b ±0.25 Measurement Units Wavelength ID c Set Reference Data Storage Tone Detection db, dbm, mw Yes Yes Yes 270 Hz, 330 Hz, 1 khz, 2 khz VISUAL FAULT LOCATOR ALL M710 OTDR MODELS Emitter Type Laser Safety Class Class II FDA 21 CFR and , IEC : Wavelength 635 ±20 nm Output Power (nominal) 0.8 mw GENERAL Display Anti-Reflective (AR) Coating Size Weight Operating Temperature Storage Temperature Power Battery Life d, f Recharge Time e, f ALL M710 OTDR MODELS cm (6.5 in), color, transflective (indoor/outdoor) touch screen display Yes x x 69.8 mm (7.5 x 10.6 x 2.75 in) 2.36 kg ( 5.22 lb) -10 C to+50 C, 0 to 90 % RH (non-condensing) -20 C to+60 C, 0 to 90 % RH (non-condensing) Rechargeable Li-Ion or AC power adapter 13 hours continuous OTDR testing 4 hours Notes: a. All specifications valid at 25 C unless otherwise specified. b. Accuracy measured at -10 dbm per N.I.S.T. standards. c. Automatic wavelength identification and switching when used with AFL s Wave ID Series Light Sources. d. Typical, per GR-196-CORE issue 2, depending on display brightness. e. Typical, from fully discharged to fully charged state, unit may be operating. f. External battery charger available. or (800) , (603) , AFL, all rights reserved. M Revision 1B,

82 M710 Multifunction OTDR Ordering Information The M710 OTDRs work with the DFS1 Digital FiberScope (the DFS1 includes a software update for the OTDR). The M710 models come with an integrated Visual Fault Locator (VFL, 650 nm), Optical Power Meter (OPM), and a large transflective touch screen display. Each model includes an OTDR, USB Flash drive, PC software for OTDR trace analysis and OPM loss reporting, AC adapter a, switchable test port adapters, and cleaning accessories in a soft carry case. When placing an order, select options as follows: Optical Configuration (NN), OTDR port ferrule (F), and Language (LL). Example: The model number M710-21U indicates M710 SM with UPC OTDR port ferrule, and English language option. Language option will be selected during ordering process. M710 NN F LL Optical Configuration (NN) 24 = QUAD LR (long range): 850/1300 nm MM and 1310/1550 nm SM 21 = 1310/1550/1625 nm SM 20 = 1310/1550 nm SM 40 = 1310/1550 nm SM OTDR Port Ferrule (F) U = UPC A = APC b Language (LL) c 01 = English, French, German, Italian, Polish, Portuguese, Spanish 08 = English, Traditional and Simplified Chinese Accessories Custom kits may be created by ordering an M710 OTDR model, a pre-configured accessories kit (M700 - H1) and accessories from the table below. The hard carry case has room for up to 6 Fiber Rings, test leads/jumpers, the DFS1 Digital FiberScope kit, OLS2-Dual or OLS4 optical light source, and cleaning accessories (items must be ordered separately). DESCRIPTION Pre-configured Accessories Kit Includes hard case with One-Click Cleaner SC/ST/FC (2.5 mm), One-Click Cleaner LC/MU (1.25 mm), and CleanConnect 500 Hard carry case,m7x0/c SERIES,W/FOAM DFS1 Digital FiberScope PC/UPC Inspection Kit DFS1 Digital FiberScope APC Inspection Kit DFS1 USB Digital Fiber Inspection Kit without Adapters OLS2-Dual laser light source with Wave ID, 1310/1550 nm OLS4 integrated LED and laser light source with Wave ID, 850/1300/1310/1550 nm Fiber Ring, standard, 1 fiber, 50/125 µm multimode, 150 m Fiber Ring, standard, 1 fiber, Laser Optimized, 50 µm multimode, 150 m Fiber Ring, standard, 1 fiber, 62.5/125 µm multimode, 150 m Fiber Ring, standard, 1 fiber, single-mode, 150 m Zippered Jumper Carry Case All types of fiber optic cleaning supplies are available. Visit or call factory for details. AFL NO. M700 - H PZ DFS XU DFS XA DFS XN OLS2-Dual OLS4 FR1-M5-150-x1-x2 d FR1-L5-150-x1-x2 d FR1-M6-150-x1-x2 d FR1-SM-150-x1-x2 d PZ Notes: a. Specify power cord type (country) when ordering an OTDR. One power cord is included with each AC adapter at no charge. b. Available on the SM port for -20, -21, -24 models only. c. When ordering OTDR, indicate language preference for the OTDR Quick Reference Guide. d. When ordering Fiber Rings, specify connector types (x1, x2). International Sales and Service Contact Information Available at or (800) , (603) , AFL, all rights reserved. M Revision 1B,

83

84 CAT