EY6450-U1. Cordless Drill & Driver CONTENTS SPECIFICATIONS ORDER NO.PTD0308U33C1 F16
|
|
- Paula Hutchinson
- 5 years ago
- Views:
Transcription
1 ORDER NO.PTD0308U33C1 F16 EY6450-U1 Cordless Drill & Driver SPECIFICATIONS CONTENTS Page Page 1 SCHEMATIC DIAGRAM 2 2 WIRING CONNECTION DIAGRAM 2 3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS 3 4 TROUBLESHOOTING GUIDE 7 5 EXPLODED VIEW 9 6 REPLACEMENT PARTS LIST Matsushita Electric Works Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
2 EY6450-U1 1 SCHEMATIC DIAGRAM 2 WIRING CONNECTION DIAGRAM 2
3 3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS HOW TO DISASSEMBLE KEYLESS CHUCK. Ref. No. 1A Procedure 1A Removal of the Keyless Drill Chuck. 1. Set the clutch handle to position 1 and select "LOW" position. 2. Turn the lock collar counterclockwise direction to open the chuck jaws. 3. Use a screwdriver to turn the chuck fastening screw inside the chuck clockwise direction of the arrow, and remove the screw. (See Fig. 1) NOTE : If the chuck fastening screw will not come loose, insert the allen wrench into the chuck and lightly tap in the clockwise direction with a hammer to tighten the chuck, and then loosen the chuck fastening screw. (See Fig. 2) 4. Insert the allen wrench into the chuck, and turn counterclockwise Fig. 1 direction in the arrow with holding the unit by the vise to remove the chuck. (See Fig. 3) EY6450-U1 Fig. 2 Fig. 3 3
4 EY6450-U1 HOW TO DISASSEMBLE MAIN UNIT. Ref. No. 2A Procedure 2A Removal of the Housing. 1. Remove the side handle. (See Fig. 4) 2. Remove nine housing screws. (See Fig. 5) NOTE : Grease rubbing part of housing with Shell Alvania for assembly. (See Fig. 6) Fig. 4 Fig. 6 Fig. 5 Ref. No. 2B Procedure 2A 2B Removal or attachment of the Motor. (Removal) 1. Take out the motor with the gear box block from housing. 2. Separate the motor from the gear box block by twisting the motor to unlock tabs. (See Fig. 7) (Attachment) 3. Motor mounting base and the positioning rib of gear case should be set. Fig. 7 4
5 Ref. No. 2C Procedure 2A 2B 2C Removal or attachment of the Gear Box Block. (Removal) 1. Turn the thrust plate to remove. 2. The internal parts of gear box block can be removed one after another. (See Fig. 8) EY6450-U1 (Attachment) 1. If the lock ring comes out, reassemble in the correct direction. (See Fig. 9) 2. Start from inserting 6 pins into the driving block as shown in the Fig Assemble the other parts in reverse order as shown in the Fig Install steel balls, pins and clutch springs into 6 holes. (See Fig. 11) NOTE : Carrier, Ring gear, and Clutch plate have their own correct directions for proper assembly. Fig. 8 Fig. 9 Fig. 11 Fig. 10 5
6 EY6450-U1 Ref.No.2D Procedure 2A 2B 2C 2D Assembly of the Adjusting Screw and the Clutch Handle. 1. Hold the driving block with the click spring on top, and align the smallest projection of adjusting screw with the driving block at 5 o clock position. NOTE: Make sure that the adjusting screw has its own correct direction for proper assembly. Failure to do so, the clutch handle does not rotate properly. (See Fig. 12) 2. Turn the adjusting screw into the driving block about 255 rotation (to 2 o clock position) for clockwise direction. (See Fig. 13) 3. Set the clutch handle with position 1 on top. (See Fig. 14) Fig. 12 Fig. 14 Fig. 13 Ref.No.2E Procedure 2A 2B 2C 2D 2E Assembly of the Switch. 1. Press fit the lead wires firmly and set the black lead wire on top. 2. Connect the switch with the white and black lead wire at 55 position. (See Fig. 15). Fig. 15 6
7 4 TROUBLESHOOTING GUIDE (Refer to WIRING CONNECTION DIAGRAM) < TROUBLE > < CHECK > < REMEDY > Does not operate. <CHECK BATTERY PACK.> NO Replace battery pack. If no less than 18V DC is available across the (+) and (-) terminals, the battery pack is OK. NOTE: The battery pack is sold separately as an optional accessory. See the nearest sales dealer for details. The battery pack has a limited life. The pack should be replaced if; - after being charged for the rated charging time the battery voltage is less than 18V DC or the usable time is extremely short. - the battery leaks. Check battery for leaks and terminals for corrosion. EY6450-U1 OK <CHECK TERMINAL CONNECTIONS BETWEEN MAIN UNIT NO Repair contacts. AND BATTERY PACK.> Check for proper terminal contacts. OK <CHECK SWITCH BLOCK.> NO Contacts in switch block (See WIRING CONNECTION DIAGRAM.) are defective. Check continuity between following terminals. Replace switch & FET * Inspection of the forward / reverse selection switch. block. When switch handle is depressed all the way: - There should be 0Ω between (A) - (D), and between (B) - (C) ; when switch lever is set to forward side. - There should be 0Ω between (A) - (C), and between (B) - (D) ; when switch lever is set to reverse side. * Inspection of the brake. When switch handle is not depressed: - There should be 0Ω between (A) - (B). OK <CHECK MOTOR.> NO Replace motor. The motor normally operates with its white (+) and black (-) lead wires connected to 18V DC. 7
8 EY6450-U1 < TROUBLE > < CHECK > < REMEDY > Does not speed- <CHECK FET.> NO Repair the contact control or does not Even if FET block is defective, it can not be replaced individually. or replace switch brake. Replace whole switch block. & FET block. Remove the FET circuit block and check the lead wire terminals. These terminals are open normally when there is an open circuit ( Ω) between the green and yellow lead wires, and between the blue and yellow lead wires. NOTE: * FET is weak against static electricity. ** The resistance value may be some differences depends on the measurement range. OK <CHECK SWITCH BLOCK.> NO Replace switch & FET block. 8
9 5 EXPLODED VIEW EY6450-U1 9
10 EY6450-U1 6 REPLACEMENT PARTS LIST NOTE: *B=only available as set *C=available individually Ref.No. Part No. Part Name & Description Remarks Per Unit 1 WEY6450K3078 HOUSING AB SET 1 2 EY6481L0177 CLICK SPRING 1 3 WEY6450L6808 CHUCK FASTENING SCREW 1 5 WEY6450Y3228 CLUTCH HANDLE 1 6 WEY6450L0638 ADJUSTING SCREW 1 7 WEY6450L0578 CLUTCH PLATE 1 8 WEY6450L0168 CLUTCH SPRING (6pcs/PK) 6 9 WEY6813L1927 STEEL BALL (6pcs/PK) WEY6450L0388 PIN (6pcs/PK) 5.3* WEY6450L1078 DRIVING BLOCK 1 12 EY6283L0377 PIN (6pcs/PK) 3.175* EY6901L1107 CARRIER 1 14 WEY6450L1488 RING GEAR 1 15 WEY6450L1348 PLANET GEAR (3pcs/PK) 3 16 WEY6450L0858 THRUST PLATE 1 17 WEY6450L1768 GEAR CASE 1 18 EY6406K9038 TORX TAPPING SCREW *C K WEY6450L1128 CARRIER A 1 20 WEY6450L1358 PLANET GEAR A (3pcs/PK) 3 21 WEY6200B1468 RING GEAR B 1 22 WEY6450L1118 CARRIER 1 23 WEY6450L1478 RING GEAR 1 24 EY6200B1367 PLANET GEAR (3pcs/PK) 3 25 WEY6450L0868 THRUST PLATE 1 26 WEY6450L0178 CLICK SPRING A 1 27 EY6406Y3238 H/L CHANGE HANDLE 1 28 WEY6405Y3248 F/R SELECTOR HANDLE 1 29 EYT184L6077 SCREW *C K WEY6450L0028 MOTOR MOUNTING PLATE 1 31 WEY6450L1008 DC MOTOR 1 32 WEY6450S6028 SEMS SCREW *C K WEY6450Y2008 SWITCH 1 34 EY6406L2568 HEAT SINK with a screw 1 35 EY6230L0207 DUST PREVENTIVE PLATE 1 36 EY6230K9218 TORX TAPPING SCREW *C K WEY6450L1458 GEAR BOX BLOCK 1 38 WEY6450K4628 SIDE HANDLE 1 - WEY6450K8108 OPERATING INSTRUCTIONS 1 **Battery Pack, Keyless Chuck, and Tool Case are available as an optional accessory. See the nearest sales dealer for details. ***For replacement parts of charger, see the charger service manual. Charger complete set is available as an optional accessory. See the nearest sales dealer for details. 10
EY6405-U1 EY6409-U1 EY6432-U1
ORDER NO.PTD0207U33C1 F16 EY6405-U1 EY6409-U1 EY6432-U1 Cordless Drill & Driver SPECIFICATIONS CONTENTS Page Page 1 SCHEMATIC DIAGRAM 2 2 WIRING CONNECTION DIAGRAM 2 3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS
More informationEY6105-X8. Cordless Drill & Driver CONTENTS SPECIFICATIONS ORDER NO.PTD0411X48C8
ORDER NO.PTD0411X48C8 Cordless Drill & Driver SPECIFICATIONS CONTENTS Page Page 1 SCHEMATIC DIAGRAM 2 2 WIRING CONNECTION DIAGRAM 2 3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS 3 4 TROUBLESHOOTING GUIDE 7 5 EXPLODED
More informationTABLE OF CONTENTS. Cordless Drill & Driver / Cordless Hammer Drill & Driver. (Cordless Drill & Driver) (Cordless Hammer Drill & Driver)
Order Number PTD1007X51CE Cordless Drill & Driver / Cordless Hammer Drill & Driver Model No. EY7441 (Cordless Drill & Driver) Model No. EY7940 (Cordless Hammer Drill & Driver) Europe and Oceania TABLE
More informationEY6813-X8. Cordless Rotary Hammer CONTENTS SPECIFICATIONS ORDER NO.PTD0212X37C8
ORDER NO.PTD0212X37C8 EY6813-X8 Cordless Rotary Hammer SPECIFICATIONS CONTENTS Page Page 1 SCHEMATIC DIAGRAM 2 2 WIRING CONNECTION DIAGRAM 2 3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS 3 4 TROUBLESHOOTING GUIDE
More informationEY7450 (Cordless Drill & Driver)
Order Number PTD1103X35CE Cordless Drill & Driver / Cordless Hammer Drill & Driver Model No. EY7442 EY7450 (Cordless Drill & Driver) Model No. EY7950 (Cordless Hammer Drill & Driver) Europe and Oceania
More informationEY3551-U1 EY3552-U1. Cordless Wood Saw / Cordless Metal Cutter CONTENTS SPECIFICATIONS ORDER NO.PTD0501U30C1 F16
ORDER NO.PTD0501U30C1 F16 Cordless Wood Saw / Cordless Metal Cutter EY3551-U1 EY3552-U1 SPECIFICATIONS CONTENTS Page Page 1 SCHEMATIC DIAGRAM 2 2 WIRING CONNECTION DIAGRAM 2 3 DISASSEMBLY INSTRUCTIONS
More informationTABLE OF CONTENTS. Cordless Impact Driver. Model No. EY7542. Europe Oceania
Order Number PTD0707X38CE Cordless Impact Driver Model No. EY7542 Europe Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications -----------------------------------------------------
More informationTABLE OF CONTENTS. Cordless Rotary Hammer Drill & Driver. Model No. EY7840. Europe and Oceania
Order Number PTD0803X31CE Cordless Rotary Hammer Drill & Driver Model No. EY7840 Europe and Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications
More informationTABLE OF CONTENTS. Cordless Hammer Drill & Driver. Model No. EY79A2. Europe Oceania
ORDER NO. PTD1511X06CE Cordless Hammer Drill & Driver Model No. EY79A2 Europe Oceania TABLE OF CONTENTS PAGE 1Warning--------------------------------------------------------------2 2Specifications-----------------------------------------------------2
More informationTABLE OF CONTENTS. Cordless Drill & Driver. Model No. EY74A2. Europe Oceania
ORDER NO. PTD1507X58CE Cordless Drill & Driver Model No. EY74A2 Europe Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications -----------------------------------------------------
More informationTABLE OF CONTENTS. Cordless Impact Driver. Model No. EY75A7. Europe Oceania
ORDER NO. PTD1507X57CE Cordless Impact Driver Model No. EY75A7 Europe Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications-----------------------------------------------------
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Model No. Description DP4010, DP4011 2-Speed Drill 13mm (1/2") L PRODUCT P 1/ 8 CONCEPT AND MAIN APPLICATIONS Models DP4010 and DP4011 have been developed as 13mm (1/2") Drill for
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Model. Description DDF481 (XFD07*1) 18V Cordless driver drill *1 Model number for USA CONCEPT AND MAIN APPLICATIONS Model DDF481 (XFD07*1) is a supreme class cordless driver drill
More informationA B 0 0 C D E 6 7 G F F H 8 9 K M O O L N I J 1
1 2 1 5 4 3 2 2 1 6 3 8 7 1 9 4 C A B 5 0 0 D E 6 G 7 F F H 8 K 9 M O O I J L N 1 GENERAL OPERATIONAL PRECAUTIONS 1. Keep work area clean. Cluttered areas and benches invite accidents. 2. Avoid dangerous
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. Description BHR202 Cordless Combination Hammer CONCEPT AND MAIN APPLICATIONS The subject model features 18V Li-ion Battery and 3 mode selection for ensuring an operator
More information1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
More informationMaintenance Information
45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Model No. Description BHP452 Cordless Percussion Driver Drill 13mm (1/2") L PRODUCT P 1/ 8 CONCEPT AND MAIN APPLICATIONS Model BHP452 has been developed as a cost-competitive 18V
More informationPlease take to time to read the provided manufacturers literature for the cordless drill and Masterflex EasyLoad 3 pump head.
MHEproducts.com DrillPump3 Instruction Manual Ver. 1.00, July, 3 2018 DRAFT Congratulations! We hope that you enjoy your new DrillPump Model 3, and that it will assist you with your field work for many
More informationOwner's Manual. Variable Speed / Reversible PROFESSIONAL 3/8 in. CORDLESS DRILL-DRIVER. Model No
Owner's Manual Variable Speed / Reversible PROFESSIONAL 3/8 in. CORDLESS DRILL-DRIVER Model No. 973.274960 SAFETY OPERATION MAINTENANCE PARTS LIST Save this manual for future reference CAUTION: Read and
More informationOwner's Manual. Variable Speed / Reversible INDUSTRIAL 3/8 in. CORDLESS DRILL-DRIVER. Model No CAUTION:
Owner's Manual Variable Speed / Reversible INDUSTRIAL 3/8 in. CORDLESS DRILL-DRIVER Model No. 315.274940 SAFETY OPERATION MAINTENANCE PARTS LIST Save this manual for future reference CAUTION: Read and
More informationSERVICE PARTS LIST 1-1/8" ROTARY HAMMER MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON RD., BROOKFIELD, WI Drwg.
00 0 200 204 276 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS PAGE 1 OF 3 BULLETIN NO.
More informationMaintenance Information
16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More informationDV 12DV DV 12DV POWER TOOLS CORDLESS IMPACT DRILL TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL DV 12DV POWER TOOLS D CORDLESS IMPACT DRILL DV 12DV TECHNICAL DATA AND SERVICE MANUAL LIST No. F852 Jul. 2001 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT Notice for use Specifications
More information462 Leap Task Chair and Stool Pneumatic Cylinder Adjustment/Replacement
462 Leap Task Chair and Stool Pneumatic Cylinder Adjustment/Replacement or a flat-bladed screwdriver that is 8" or longer 1/8 ALLEN WRENCH If you have a problem, question, or request, call your local dealer,
More informationCordless Driver Drill DS 9DVC DS 12DVC
Cordless Driver Drill DS 9DVC DS 12DVC HANDLING INSTRUCTIONS DS 12DVC Read through carefully and understand these instructions before use. 1 2 3 6 5 1 3 2 3 4 12 3 7 1 2 0 8 u 4 1 5 6 2 @ # # $!! 5 0 9
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Model No. Description GA5020C/GA6020C, GA5021C/GA6021C Angle Grinders 125mm (5") /150mm (6") L PRODUCT P 1/10 CONCEPT AND MAIN APPLICATIONS These four models have been developed as
More informationOwner's Manual. Two Speed / Reversible 3/8 in. CORDLESS DRILL-DRIVER. Model No
Owner's Manual Two Speed / Reversible 3/8 in. CORDLESS DRILL-DRIVER Model No. 315.111790 SAFETY OPERATION MAINTENANCE PARTS LIST Save this manual for future reference CAUTION: Read and follow all Safety
More informationTECHNICAL INFORMATION Models No. Description
TECHNICAL INFORMATION Models No. Description,, Cordless Driver Drill CONCEPTION AND MAIN APPLICATIONS / 9.6V : 2 speed mechanic & variable speed control version of the existing Mod.. : 12 V version of
More informationDS 14DVF DS 14DVF POWER TOOLS CORDLESS DRIVER DRILL TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL POWER TOOLS D CORDLESS DRIVER DRILL TECHNICAL DATA AND SERVICE MANUAL LIST No. F869 Feb. 2002 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT CONTENTS Page 1. PRODUCT NAME... 1 2.
More information2008 Toyota RAV ELECTRICAL Charging (2AZ-FE) - RAV4
2008 ELECTRICAL Charging (2AZ-FE) - RAV4 CHARGING SYSTEM PRECAUTION 1. Check that the battery cables are connected to the correct terminals. 2. Disconnect the battery cables if a quick charge is given
More informationDS 18DVB DS 18DVB POWER TOOLS CORDLESS DRIVER DRILL TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL DS 18DVB POWER TOOLS D CORDLESS DRIVER DRILL DS 18DVB TECHNICAL DATA AND SERVICE MANUAL LIST No. F844 Aug. 2001 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT Notice for use Specifications
More informationDisassembly Instructions hp. Dynafile II Models: 40352, 40353
Disassembly Instructions - 0.4 hp. Dynafile II Models: 40352, 40353 Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever
More informationHitachi. Power Tools DS 12DVF3 DS 9DVF3 DS 12DVF3 DS 9DVF3 CORDLESS DRIVER DRILLS TECHNICAL DATA AND SERVICE MANUAL MODELS
MODELS DS 12DVF3 DS 9DVF3 Hitachi Power Tools D CORDLESS DRIVER DRILLS DS 12DVF3 DS 9DVF3 TECHNICAL DATA AND SERVICE MANUAL DS 12DVF3 LIST Nos. DS 12DVF3: G818 DS 9DVF3: G817 Mar. 2005 SPECIFICATIONS AND
More informationOPERATOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NO. HP1441M
OPERATOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NO. HP11M THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER. Your new cordless drill-driver has been engineered and manufactured to Ryobi s high standard
More informationSCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray)
Preparation Part Number: 08460 21810 (Silver/Dark Gray) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description 1 1 Steering Wheel
More informationMODEL DS 7DF POWER TOOLS TECHNICAL DATA AND SERVICE MANUAL CORDLESS DRIVER DRILL DS 7DF SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
MODEL POWER TOOLS D CORDLESS DRIVER DRILL TECHNICAL DATA AND SERVICE MANUAL LIST No. F881 Mar. 2003 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT REMARK: Throughout this TECHNICAL DATA
More informationDisassembly Instructions hp. Mini-Dynafile II
Disassembly Instructions - 0.4 hp. Mini-Dynafile II Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever to deplete the
More information13 mm (1/2 in.), 24 VOLT PROFESSIONAL CORDLESS HAMMER DRILL Variable Speed / Reversible
Operator's Manual 13 mm (1/2 in.), 24 VOLT PROFESSIONAL CORDLESS HAMMER DRILL Variable Speed / Reversible Stock No. 9249 Model No. 973.2490 Save this manual for future reference WARNING: To reduce the
More informationAlternating Current Revolution per minute Protective Earth Ground. Protected from dripping water Fuse Attention, Consult Accompanying Document
GLOSSARY OF SYMBOLS: (Symbols and descriptions) Alternating Current Revolution per minute Protective Earth Ground Direct Current On (Power connection Off (power to the mains) disconnection from the mains)
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More information18V Cordless Precision Clutch Shut Off Pistol Screwdriver SPC-P2625Q SPC-P2925Q SPC-P21225Q
18V Cordless Precision Clutch Shut Off Pistol Screwdriver MODEL NO.: SPC-P2325Q SPC-P2625Q SPC-P2925Q SPC-P21225Q 2 (A) (B) (C) (D) (E) (H) (F) (G) (I) (A) 1/4" Hex with quick change chuck. (B) Covered
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
More informationPull out clutch E snap ring and withdraw complete clutch pack of clutch E. 6 HP 26 ZF Getriebe GmbH Saarbrücken CD
Press down cup spring in the mandrel press with assembly bracket 5x46 002 566 and remove snap ring with suitable pliers. Take out planet carrier and cup spring. Take the O-ring seal off the planet carrier.
More informationOPERATOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NOS. HP62 / HP722
5 OPERATOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NOS. HP62 / HP722 MODEL HP62 5 MODEL HP722 THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER. Your new cordless drill-driver has been engineered and manufactured
More informationCordless High Speed Drill
ENGLISH Cordless High Speed Drill MODEL 6503D 00039 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Model No. Description SP6000 Plunge Cut Circular Saw 165mm (6-1/2") CONCEPT AND MAIN APPLICATIONS Model SP6000 is the first Makita plunge cut saw. Features great conveniences such
More informationOPERATOR S MANUAL 18 VOLT RIGHT ANGLE DRILL
OPERATOR S MANUAL 18 VOLT RIGHT ANGLE DRILL P240 BATTERIES AND CHARGERS SOLD SEPARATELY Your right angle drill has been engineered and manufactured to Ryobi s high standard for dependability, ease of operation,
More informationMaintenance Information
16575219 Edition 4 October 2013 Air Screwdrivers QP1P, QP1S and QP1T Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
More informationTECHNICAL INFORMATION Model No. Description
TECHNICAL INFORMATION Model No. Description CONCEPT AND MAIN APPLICATIONS Specification HR2450, HR2451, HR2452 24mm (15/16 " ) Rotary Hammer The above models are the advanced version of MAKITA's famous
More informationCERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT
PAGE 1 OF 9 CERTAIN 2013-2016 MODEL YEAR FUSION AND 2013-2014 ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT OVERVIEW In some of the affected vehicles, the bushing
More informationDN 12DY DN 12DY POWER TOOLS CORDLESS ANGLE DRILL TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL POWER TOOLS D CORDLESS ANGLE DRILL TECHNICAL DATA AND SERVICE MANUAL LIST No. F883 Mar. 2003 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT REMARK: Throughout this TECHNICAL DATA
More informationCordless Hammer Drill Driver
Cordless Hammer Drill Driver Operating Instructions Model No: EY6950 IMPORTANT This manual contains safety information. Read manual completely before first using this product and save this manual for future
More informationMaintenance Information
16573347 Edition 2 February 2014 Air Grinder Series 88H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationModel 4360 Teardown and Reassembly Instructions
Clean the outside surface of the transaxle. Place the shifter in neutral position. Remove detent cover screw (item 3), detent cover (item 4), detent springs (item 5), and detent balls (item 6). Use a magnet
More informationREPAIR MANUAL URW SERIES. URW-6, 8, 9, 10 & 12 Series Repair Manual
REPAIR MANUAL URW SERIES URW-6, 8, 9, 10 & 12 Series Repair Manual Contents Page 1. Tools Needed for Repair 1 2. Disassembly and Reassembly of the Cam Casing 2-4 3. Disassembly and Reassembly of the Gear
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingcom TECHNICAL SERVICE MANUAL abrasive liquid pumps SERIES 4625 SIZES f - fh SECTION TSM 410.1 PAGE 1
More informationPRODUCT OBSOLETED 4Q16
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingcom TECHNICAL SERVICE MANUAL abrasive liquid pumps SERIES 4625 SIZES f - fh SECTION TSM 410.1 PAGE 1
More informationOPERATOR S MANUAL CORDLESS DRILL-DRIVER MODEL NOS. HP721/HP961/HP1201
OPERATOR S MANUAL CORDLESS DRILL-DRIVER MODEL NOS. HP2/HP6/HP20 THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER. Your new cordless drill-driver has been engineered and manufactured to Ryobi s high standard
More informationEP1022-U1 MASSAGE LOUNGER SPECIFICATIONS ORDER NO.HPD0104U00C1. Power consumption. : Approx. 500 times/min.(per side)
ORDER NO.HPD0104U00C1 MASSAGE LOUNGER SPECIFICATIONS Power source Power consumption Kneading speed Tapping speed Rolling massage speed Massaging width Back rolling width/tapping width Massage heads up/down
More informationMaintenance Information
16575243 Edition 2 October 2013 Air Screwdrivers 1R Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationSuper T QR20 INSTRUCTIONS GENERAL RULES
INSTRUCTIONS GENERAL RULES 1. Where specified, assemble and disassemble the shock absorption system using the MARZOCCHI special tools only. 2. On reassembling the suspension system, always use new seals.
More informationSTEERING COLUMN - TILT
STEERING COLUMN - TILT 1993 Toyota Celica 1993 STEERING Toyota - Steering Columns - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate an upper steering shaft, attached by a "U"
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More informationRev. B Page 1 of 7 SPEC. ASSY INST, REMOTE ADJUSTABLE PRE-LOAD (30-25XX & SA XX)
Page 1 of 7 SPEC. ASSY INST, REMOTE ADJUSTABLE PRE-LOAD (30-25XX & SA-5057-5XX) 19 3 10 11 4 7 20 16 14 15 12 13 21 5 9 6 17 2 1 Fig. 1 Reservoir Components Fig. 2 Housing Components 30-25XX & SA-5057-5XX
More information1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
More informationCHAPTER 7 TRANSMISSION (MFO6S)
1 page INDEX1 Model SG1J (MF06S) TRANSMISSION 7-1 7-142E-07 CHAPTER 7 TRANSMISSION (MFO6S) Model SG1J 1 Models FE, FF and SG2J 1 Model FD 7 TROUBLESHOOTING...7-2 SPECIAL TOOLS...7-5 REMOVAL...7-7 GEAR
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION PRODUCT P 1 / 15 Model No. Description HR2455 Rotary Hammer 24mm (15/16") L W CONCEPT AND MAIN APPLICATIONS Model HR2455 has been developed as a sister tool to Model HR2450, the Makita
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationMaintenance Information
Form 04584058 Edition 1 November 2004 Air Impactool 2141P and 2141PSP Maintenance Information Save These Instructions Disassembly General Instructions 1. Do not disassemble the tool any further than necessary
More informationSTARTING/CHARGING SYSTEMS Brought to you by Eris Studios NOT FOR RESALE
STARTING/CHARGING SYSTEMS General Description 1. General Description A: SPECIFICATION Vehicle model Starter Generator Item Specification Type Reduction type Model 428000-5760 Manufacturer DENSO Voltage
More informationMaintenance Information
16606022 Edition 3 May 2014 Air Drill 728 Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More informationCOMPONENT WORK SAMPLE 8 Simulated Assembly MAINTENANCE MANUAL. From 1974 to March 15, 2003
COMPONENT WORK SAMPLE 8 Simulated Assembly MAINTENANCE MANUAL From 1974 to March 15, 2003 Copyright 2008 VALPAR International Corporation P.O. Box 5767 Tucson, Arizona 85703-5767 All rights reserved. No
More informationSTEERING SYSTEM - MANUAL RACK & PINION
STEERING SYSTEM - MANUAL RACK & PINION 1993 Nissan Sentra 1993 STEERING Nissan Manual Rack & Pinion NX, Sentra DESCRIPTION & OPERATION Steering gear assembly is a manual rack and pinion type. Unit is mounted
More informationService Tools. Service and Repair Manual Model 900/950/990 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION ITEM PART NO.
12 1 3 2 4 5 8 10 6 7 9 11 14 24 12 13 17 22 29 18 23 25 19 26 15 20 27 21 16 22 33 37 38 32 31 36 30 34 35 40 41 42 43 ITEM PART NO. DESCRIPTION 1 9170 0231 30 LONG ALLEN KEY 2 9170 0737 20 3/32 PIN PUNCH
More information10A 10F 10B 10E 10A 10D 10B. Mr. T 10C Q R
Q R 2 0 23 30 12 18 17 16 15 14 37 39 38 3 7 6 5 20 26 21 22 40 13 4 2 25 24 8 1 28 27 11 31 19 10A 10D 10B 10C 10 29 10A 10F 10B 10E 10 9 32 36 33 34 35 178 15 GENERAL 82 80 Ø28.6 ±0.1 Ø30 +0.05 0 348
More informationSTERNDRIVE UNIT 3 B GEAR HOUSINGS MR/ALPHA ONE/ALPHA ONE SS
STERNDRIVE UNIT 3 B 23146 GEAR HOUSINGS MR/ALPHA ONE/ALPHA ONE SS Table of Contents Page Identification........................... 3B-1 Specifications.......................... 3B-1 Torque Specifications................
More informationGenesis Double Adjustable Shock Assembly and Repair
Genesis Double Adjustable Shock Assembly and Repair General Operating Description The Genesis Adjustable Shock is adjusted by moving one or both of two bypassing sliding valves. These valves slide longitudinally
More informationDRIVE SHAFT LOCATION INDEX
DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,
More informationSA 8 FRONT AXLE HUB COMPONENTS
SA8 FRONT AXLE HUB COMPONENTS SA9 REMOVAL OF FRONT AXLE HUB 1. REMOVE COTTER PIN, LOCK NUT CAP AND BEARING LOCK NUT (a) Remove the cotter pin and lock nut cap. (b) Loosen the bearing lock nut while depressing
More informationWARNING Carefully Read These Instructions Before Use
DO NOT RETURN THIS SPRAYER TO STORE Call: 1-800-950-4458 Backpack Sprayer Use and Care Manual Manufactured for Northern Tool + Equipment Co., Inc. WARNING Carefully Read These Instructions Before Use Model
More informationATD V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual
ATD 10525 12V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual KNOW YOUR PRODUCT (DRILL) 1. Keyless chuck 2. Torque adjustment collar 3. Speed selector 4. Forward/reverse selector 5. Battery
More informationHitachi. Power Tools DS 18DMR DS 14DMR DS 18DMR DS 14DMR CORDLESS DRIVER DRILL TECHNICAL DATA AND SERVICE MANUAL MODELS
MODELS DS 18DMR DS 14DMR Hitachi Power Tools D CORDLESS DRIVER DRILL DS 18DMR DS 14DMR TECHNICAL DATA AND SERVICE MANUAL LIST Nos. DS 18DMR: G809 DS 14DMR: G808 May 2004 SPECIFICATIONS AND PARTS ARE SUBJECT
More informationDRIVE AXLE - INTEGRAL HOUSING
DRIVE AXLE - INTEGRAL HOUSING 1993 Toyota Celica 1993 DRIVE AXLES Toyota Differentials & Axle Shafts - Integral Housing Toyota; Celica All-Trac DESCRIPTION Drive axle assembly is a hypoid type with integral
More informationSTEERING COLUMN - STANDARD
STEERING COLUMN - STANDARD 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Standard Celica DESCRIPTION & OPERATION Steering column is a collapsible 2-piece design. Columns use shear pins to
More informationSTIHL BGA STIH)
STIHL BGA 85 00- STIH) . Introduction. Safety Precautions. Specifications 5. Motor 5. Maximum air flow rate 5. Air velocity 5.4 Dimensions 5.5 Weight 5.6 Tightening Torques 6 4. Troubleshooting 7 4. Flowchart
More informationForge Motorsport BMW N54 Diverter Valves
Forge Motorsport BMW N54 Diverter Valves Please thoroughly read through and familiarize yourself with these instructions in their entirety prior to beginning any part of the installation process of any
More informationOPERATOR S MANUAL. 18 volt drill-driver P200 SAVE THIS MANUAL FOR FUTURE REFERENCE. ACCEPTS ALL one+ BATTERY PACKS
OPERATOR S MANUAL 18 volt drill-driver 2-speed P200 5 ACCEPTS ALL one+ BATTERY PACKS batteries and chargers sold Separately Your drill-driver has been engineered and manufactured to our high standard for
More informationFDS 12DVA FDS 12DVA POWER TOOLS CORDLESS DRIVER DRILL TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL FDS 12DVA POWER TOOLS CORDLESS DRIVER DRILL FDS 12DVA TECHNICAL DATA AND SERVICE MANUAL F LIST No. F835 Nov. 1999 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT REMARK: Throughout
More informationINSTRUCTION MANUAL. MODEL No: FLEXC-3PX FLEXC-8PX FLEXC-11PX FLEXC-12PX 10.8V Cordless Shut-off Screwdriver.
a) Torque adjustment cover b) 1/4" F/Hex with quick change chuck c) LED indicator provides simple process information to the operator d) LED light for working in dark area e) Press button for easy Forward/Reverse
More informationSERVICE MANUAL. Hydraulic Motors type MM
SERVICE MANUAL Hydraulic Motors type MM and MLHM 2008 Сервизно ръководство Демонтаж Хидравлични мотори Тип GW - 2/6 - Service Manual Disassembly Hydraulic Motor type MM, MLHM Instructions in this manual
More informationSECTION 7 - SUSPENSION
For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 7 - SUSPENSION 7 TABLE OF CONTENTS Front and Rear Suspension Assembly Schematics... 7-2 Shock Absorbers... 7-2 Swing Arm... 7-5 Front
More informationNOTE: Visit our website at for video repair procedures, under the Tools section.
Repair Instructions Hypro Repair Tools: Tool Box No. 3010-0168 1/4" Allen Wrench No. 3020-0008 Support Bars (2) No. 3010-0064 Port Brush No. 3010-0066 1/16" Allen Wrench No. 3020-0009 Brush Holder No.
More information22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B
22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS............................... 22A OVERHAUL..................... 22B 22A-2 GROUP 22A MANUAL TRANSAXLE CONTENTS GENERAL DESCRIPTION......... 22A-3 DIAGNOSIS 22A-6
More informationSUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.
More informationSTEERING COLUMN - TILT
STEERING COLUMN - TILT 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate a mainshaft, attached by a "U" joint to an
More information8 TROUBLESHOOTING
8 DRIVE AND DRIVEN PULLEYS/ SCHEMATIC DRAWING------------------------------------------------------------------------- 8-1 SERVICE INFORMATION-----------------------------------------------------------------------
More informationDrill Driver. Cordless 18V. Operating Instructions XDD-180. XU1 Power tools
Cordless Operating Instructions XDD-180 18V Drill Driver XU1 Power tools 1 23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 Website: www.xuone.com.au XDD-180 0916 1 2 3 4 5
More information~ ~j)~~ @) A WC (after 5/91) STURMEY ARCHER 3 SPEED COASTER BRAKE S3C
STURMEY ARCHER 3 SPEED COASTER BRAKE A WC (after 5/91) ~ ~j)~~ @@ ~~@~~ @) @@ S3C «~ @OOlQj@l~ 'The lockwasher, brake arm nut and brake arm as a unit may be interchanged. 2Same as AW. 3HSA 469 replaces
More information