Stewart-Warner Electronic Tachometer 54.07

Size: px
Start display at page:

Download "Stewart-Warner Electronic Tachometer 54.07"

Transcription

1 General Description General Description Engine speeds are shown in revolutions-per-minute (rpm) by the electronic tachometer (Fig. 1). The tachometer is used as a guide for shifting, and to keep the engine speed in the proper rpm range. The electronic tachometer consists of a gauge, magnetic sensor (Fig. 2), and the electrical wires that complete the circuit between the two components. The electronic tachometer receives signals from the magnetic sensor, which extends through a threaded bore in the flywheel housing (Fig. 3). When the vehicle is moving, the teeth of the turning flywheel generate electrical pulses in the sensor s magnetic field. These pulses are transmitted to the tachometer head, which converts the signals to an rpm reading Flywheel Teeth 2. Flywheel Housing 3. Magnetic Sensor f RPM X Fig. 3 f Fig Locknut 2. Sensor 3. Weather Pack Connector f Fig. 2, Magnetic Sensor Assembly Heavy-Duty Trucks Service Manual, Supplement 0, July /1

2

3 Tachometer Head Replacement Replacement 1. Apply the parking brakes. 2. Turn off the ignition. 3. Remove the screws that attach the tachometer/ speedometer panel to the dash. Pull the panel out to gain access to the back of the tachometer head. See Fig Unplug the electrical wiring connectors from the tachometer head. 5. Remove the nuts that attach the mounting bracket to the tachometer head, and remove the bracket. Remove the tachometer head by pulling it out from the front of the panel. 6. Calibrate the new tachometer head to the vehicle s engine. For instructions, refer to Subject Place the new tachometer head in the dash panel. Attach the mounting bracket to the tachometer head, then tighten the nuts. 8. Connect the electrical wiring connectors to the tachometer head. 9. Position the panel, then install the screws that attach the tachometer/speedometer panel to the dash. f Fig. 1 Heavy-Duty Trucks Service Manual, Supplement 0, July /1

4 Magnetic Sensor Replacement and Adjustment Replacement and Adjustment 1. Disconnect the Weather Pack connector. See Fig Loosen the magnetic sensor locknut. Remove the sensor from the flywheel housing. 3. Screw the new magnetic sensor into the flywheel housing until it bottoms out on the gear teeth. Back off the sensor one-half turn. See Fig. 2. IMPORTANT: The tachometer reading will be wrong if the correct adjustment is not maintained. 4. Hold the magnetic sensor in place to keep it from turning. Tighten the locknut 18 lbf ft (25 N m). 5. Connect the Weather Pack connector. 6. Test drive the vehicle and check that the tachometer is operating. If there is no tachometer reading, the magnetic sensor was probably not adjusted correctly; readjust the sensor Fig Flywheel Teeth 2. Flywheel Housing 3. Magnetic Sensor f Locknut 2. Sensor 3. Weather Pack Connector f Fig. 1, Magnetic Sensor Assembly Heavy-Duty Trucks Service Manual, Supplement 0, July /1

5 Calibrating the Tachometer Head Calibrating the Tachometer Head LIGHTBULB If a new tachometer head is installed, or if a new engine is installed, you must also recalibrate the tachometer head. The Stewart-Warner tachometer is calibrated by setting eight DIP switches at the back of the tachometer head. See Fig. 1. The DIP switches are set according to the engine model used in the vehicle. Determine the tachometer calibration setting as follows: 1. Adjust the magnetic sensor. For instructions, refer to Subject Obtain the calibration code from the table listing codes in Specifications, Remove the tachometer head from the panel. For instructions, refer to Subject Remove the plastic cover from the DIP switch panel at the back of the tachometer head. Calibrate the tachometer by moving DOWN each switch that corresponds to the 0 (zero) positions of the calibration code. See Fig. 2. Move UP each switch that corresponds to the 1 (one) positions of the calibration code. See Fig Install the plastic cover on the DIP switch panel. 6. Install the tachometer head in the panel. For instructions, refer to Subject 100. DIP SWITCHES DIP SWITCHES Fig CALIBRATION CODE Fig. 2 f f Heavy-Duty Trucks Service Manual, Supplement 0, July /1

6 Troubleshooting Troubleshooting The following is a troubleshooting process requiring the use of a voltmeter and an ohmmeter. Make the checks in the order listed below. Incorrect tachometer head readings may occur whenever a new tachometer head or engine is installed. In each case, calibrate the tachometer head using the procedure in this section. Inaccurate readings will also occur if the magnetic sensor is not adjusted correctly. Before troubleshooting the system, make sure the magnetic sensor is correctly adjusted. For instructions, see Subject 110. Also, make sure the batteries are fully charged. MAGNETIC SENSOR VOLTAGE CHECK NOTE: To receive an accurate tachometer reading, a minimum of one volt AC output is needed from the magnetic sensor. 1. Disconnect the electrical connector from the sensor. Make sure the sensor terminals are free of corrosion and moisture. 2. Connect an AC voltmeter to the terminals of the magnetic sensor. 3. Run the engine at idle speed, and check the voltage output from the sensor. If the voltage is less than one volt, refer to the "Troubleshooting Chart" for possible causes and corrections. 4. Turn off the engine and disconnect the voltmeter. MAGNETIC SENSOR RESISTANCE CHECK USING AN OHMMETER Connect the ohmmeter leads to the terminals of the magnetic sensor. The resistance should measure 876 ohms. Readings between 788 and 963 ohms are acceptable. If the resistance is acceptable, then inaccurate tachometer readings are caused by either the wiring to the tachometer head or by the tachometer head itself. Go to "Wiring Check: Magnetic Sensor to Tachometer Head." If the resistance is outside the acceptable range, replace the sensor with a new one. For instructions, see Subject 110. WIRING CHECK: MAGNETIC SENSOR TO TACHOMETER HEAD 1. Remove the screws that attach the tachometer/ speedometer panel to the dash. Pull the panel out to gain access to the back of the tachometer head. 2. Unplug the electrical wiring connector from the tachometer head. 3. Check for an open or short circuit by disconnecting the magnetic sensor leads, circuit numbers 162 and 163. Connect the ohmmeter to the leads of circuit numbers 162 and 163. The resistance should measure 876 ohms. A reading between 788 and 963 ohms is acceptable. If the above reading is not obtained, and the magnetic sensor is operative, the problem is in the wiring between the magnetic sensor and the tachometer head. Repair or replace the damaged wiring. If the reading is between 788 and 963 ohms, connect the magnetic sensor leads to the tachometer head. Go to "Battery Voltage Check Using a DC Voltmeter." BATTERY VOLTAGE CHECK USING A DC VOLTMETER 1. With the ignition switch off, attach the probes of the DC voltmeter across the positive and negative terminals of the tachometer head. NOTE: Attach the negative (black) probe to the yellow wire terminal and the positive (red) probe to the red wire terminal. 2. Turn on the ignition switch. The voltmeter should read 9 to 16 volts DC. If the voltage is between 9 and 16 volts DC, but the tachometer meter readings are inaccurate, then the tachometer head, not the wiring is causing inaccurate readings. Turn off the ignition switch, and disconnect the voltmeter probes. Replace the tachometer head. For instructions, see Subject 100. If the voltage is not between 9 and 16 volts DC, check the wiring between the ignition switch and the tachometer head. Turn off the ignition switch, Heavy-Duty Trucks Service Manual, Supplement 0, July /1

7 54.07 Troubleshooting Stewart-Warner Electronic Tachometer and disconnect the voltmeter probes. Repair or replace the damaged wiring. 3. Place the panel in the dash; install and tighten the screws. Troubleshooting Chart Problem Less Than One Volt Reading from the Magnetic Sensor Possible Cause Magnetic sensor gap is not properly adjusted. The magnetic sensor is damaged. Adjust the magnetic sensor. Replace the magnetic sensor. Remedy Problem Tachometer Head Will Not Register Possible Cause Magnetic sensor gap is not properly adjusted. The magnetic sensor is damaged. The tachometer head is damaged internally. Loose or corroded terminals, broken contacts, broken wires, shorting, or frayed wires are causing an incomplete circuit. Adjust the magnetic sensor. Replace the magnetic sensor. Remedy Replace only after checking all other possible causes. Replace the damaged component(s), as necessary. Problem Inaccurate Tachometer Readings Possible Cause Magnetic sensor gap is not properly adjusted. Shorts are occurring in the magnetic sensor. The tachometer head is incorrectly calibrated. Erratic readings are resulting from loose electrical connections. Adjust the magnetic sensor. Remedy Check the resistance of the magnetic sensor. Replace the sensor, if necessary. Recalibrate the tachometer head. Check all the wiring in the tachometer system. Tighten all loose connections. 300/2 Heavy-Duty Trucks Service Manual, Supplement 0, July 1992

8 Specifications Calibration codes by engine for Stewart Warner electronic tachometers. Engine Manufacturer Engine Model Calibration Code Detroit All Caterpillar and Cummins NTC Big Cam III & IV L Table 1 Heavy-Duty Trucks Service Manual, Supplement 0, July /1

Tachometer, Ametek Electronic 54.21

Tachometer, Ametek Electronic 54.21 General Information General Information The Ametek electronic tachometer consists of a dash-mounted gauge, a magnetic sensor mounted on the flywheel housing, and the necessary electrical wiring. An optional

More information

Starter, Delco Remy 15.01

Starter, Delco Remy 15.01 Starter, Delco Remy.0 General Information General Information The Delco Remy starter mounts at the forward face of the flywheel bell housing on the right side of the engine. The starter assembly consists

More information

CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM 1993 Mitsubishi Montero 1993 ACCESSORIES & EQUIPMENT Mitsubishi Cruise Control Systems Montero DESCRIPTION & OPERATION The cruise control system is electronically and vacuum controlled.

More information

System III Wiring Information 54-12

System III Wiring Information 54-12 System III Wiring Information 54-12 System Operation General Information Initial Power On Description of Revisions: This service bulletin is updated and replaces the version dated September 2002. This

More information

HLY-3015 MINI SPEED/TACH INFORMATION SYSTEM (weather and vibration resistant for exposed environments)

HLY-3015 MINI SPEED/TACH INFORMATION SYSTEM (weather and vibration resistant for exposed environments) HLY-3015 MINI SPEED/TACH INFORMATION SYSTEM (weather and vibration resistant for exposed environments) Neutral Left turn Low voltage Right turn High beam Engine Low oil *To avoid damage to motorcycle,

More information

CONTROL BOX. Wiring the control box into the vehicle. +12V

CONTROL BOX. Wiring the control box into the vehicle. +12V CONTROL BOX Once the display panel is in place, mount the control box within the connecting cable's distance (approximately 3 feet) and secure to the underside of the dashboard. This case does not have

More information

INSTALLATION GUIDE Six Gauge Universal Digital Dash Panel Part Number: DP10002

INSTALLATION GUIDE Six Gauge Universal Digital Dash Panel Part Number: DP10002 Made in America Lifetime Guarantee Thank you for purchasing this digital dash panel from Intellitronix. We value our customers! INSTALLATION GUIDE Six Gauge Universal Digital Dash Panel Part Number: DP10002

More information

1984 Jeep CJ7. IGNITION SYSTEM - SOLID STATE' 'Distributors & Ignition Systems MOTORCRAFT SOLID STATE IGNITION (SSI)

1984 Jeep CJ7. IGNITION SYSTEM - SOLID STATE' 'Distributors & Ignition Systems MOTORCRAFT SOLID STATE IGNITION (SSI) TESTING SECONDARY CIRCUIT CHECK CAUTION: When checking secondary voltage, do not remove spark plug wires from spark plugs No. 3 on 4-cylinder, No. 1 or 5 on 6-cylinder and No. 3 or 4 on V8 Engines. 1.

More information

MODEL HLY-2001 rev. B TANK MOUNT SPEEDOMETER/TACHOMETER INFORMATION SYSTEM

MODEL HLY-2001 rev. B TANK MOUNT SPEEDOMETER/TACHOMETER INFORMATION SYSTEM MODEL HLY-2001 rev. B TANK MOUNT SPEEDOMETER/TACHOMETER INFORMATION SYSTEM Please read this before beginning installation or wiring. POWER Connect the red wire from the main harness to accessory power

More information

Igniter Unit Test ACCORD AND PRELUDE WITH HITACHI DISTRIBUTOR. See Figure 2

Igniter Unit Test ACCORD AND PRELUDE WITH HITACHI DISTRIBUTOR. See Figure 2 Igniter Unit Test 1984-89 ACCORD AND PRELUDE WITH HITACHI DISTRIBUTOR See Figure 2 This procedure is not applicable to 1988-89 fuel injected Preludes. 1. Remove the distributor cap. 2. Disconnect the lead

More information

ESC2301. Universal Electronic Governor Controller Operation Manual

ESC2301. Universal Electronic Governor Controller Operation Manual ESC2301 Universal Electronic Governor Controller Operation Manual *Replaces most Woodward, Barber Colman & Cummins Speed Controls Features Smoke Limit Control, Idle Speed Control, 12V or 24V input Suitable

More information

1984 Toyota Pickup. IGNITION SYSTEM - NIPPONDENSO ELECTRONIC' '1984 ELECTRICAL Toyota Ignition System - Nippondenso Electronic Ignition

1984 Toyota Pickup. IGNITION SYSTEM - NIPPONDENSO ELECTRONIC' '1984 ELECTRICAL Toyota Ignition System - Nippondenso Electronic Ignition ADJUSTMENTS 1984 Toyota Pickup PICK-UP COIL-TO-SIGNAL ROTOR (RELUCTOR) AIR GAP 1. Using a flat, non-magnetic feeler gauge, check air gap between pick-up coil pole piece and each reluctor tooth. Gaps should

More information

INSTRUMENT PANEL AND GAUGES INSTRUMENT PANEL AND GAUGES XJ

INSTRUMENT PANEL AND GAUGES INSTRUMENT PANEL AND GAUGES XJ J INSTRUMENT PANEL AND GAUGES 8E - 1 INSTRUMENT PANEL AND GAUGES GROUP INDEX INSTRUMENT PANEL AND GAUGES XJ... 1 INSTRUMENT PANEL AND GAUGES YJ... 24 INSTRUMENT PANEL AND GAUGES XJ CONTENTS page DIAGNOSIS...

More information

CUMMINS FAULT CODE: 1239 PID: SPN: 2623 FMI: 3/3 LAMP: AMBER

CUMMINS FAULT CODE: 1239 PID: SPN: 2623 FMI: 3/3 LAMP: AMBER CUMMINS ACCELERATOR PEDAL OR LEVER POSITION SENSOR 2 CIRCUIT - VOLTAGE ABOVE NORMAL OR HORTED TO HIGH SOURCE FAULT CODE: 1239 PID: SPN: 2623 FMI: 3/3 LAMP: AMBER DESCRIPTION ISX and ISM Accelerator Pedal

More information

ANTI-LOCK BRAKE SYSTEM

ANTI-LOCK BRAKE SYSTEM ANTI-LOCK BRAKE SYSTEM 1993 Mitsubishi Diamante 1993 BRAKES Mitsubishi - Anti-Lock Brake System Diamante DESCRIPTION The Anti-Lock BRAKE SYSTEM (ABS) is designed to prevent wheel lock-up during heavy braking.

More information

CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM 1994 Volvo 960 1994 ACCESSORIES/SAFETY EQUIPMENT Cruise Control System 960 DESCRIPTION & OPERATION MAIN SWITCH Cruise control main switch is located at end of directional signal lever.

More information

w.get2itparts.com Viper 90R-4 Dies After Shifting Or Indicator Lights Blink SCL /24/2005

w.get2itparts.com   Viper 90R-4 Dies After Shifting Or Indicator Lights Blink SCL /24/2005 10/24/2005 Viper 90R-4 Dies After Shifting Or Indicator Problem: Unit will not shift into gear or engine dies when shifting into gear. (1) i. Turn on the ignition switch. ii. Set selector switch to neutral

More information

SD Bendix ET-2 Electronic Treadle DESCRIPTION OPERATION

SD Bendix ET-2 Electronic Treadle DESCRIPTION OPERATION SD-15-4106 Bendix ET-2 Electronic Treadle PIVOT SPRING MOUNTING BASE DESCRIPTION CONNECTOR FIGURE 1 - ET-2 ELECTRONIC TREADLE ROLLER TREADLE COVER DOUBLE RETURN SPRING CABLE ASSEMBLY The ET-2 is an electronic

More information

FAULT CODE 131 (IVS) Accelerator Position Sensor Circuit

FAULT CODE 131 (IVS) Accelerator Position Sensor Circuit FAULT CODE 131 (IVS) Accelerator Position Sensor Circuit Overview CODE REASON EFFECT Fault Code: 131 PID: P091 SPN: 91 FMI: 3 LAMP: Red SRT: 00-084 High voltage detected at accelerator position signal

More information

INSTRUMENT PANEL - STANDARD

INSTRUMENT PANEL - STANDARD INSTRUMENT PANEL - STANDARD 1988 Toyota Celica 1988 SWITCHES & INSTRUMENT PANELS Toyota - Standard Camry DESCRIPTION & OPERATION GAUGES Some instrument panels are equipped with a tachometer, oil pressure

More information

Before performing spark test, ensure ignitor is properly grounded.

Before performing spark test, ensure ignitor is properly grounded. Page 1 of 10 IGNITION CHECKS SPARK TEST NOTE: Before performing spark test, ensure ignitor is properly grounded. 1. Disconnect high tension coil wire from distributor. Hold coil wire approximately 1/2"

More information

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer 95 Aerostar/Ranger/Explorer Section 13-01: Instrument Cluster, Conventional DIAGNOSIS AND TESTING 95 Aerostar/Ranger/Explorer Workshop Manual Pinpoint Tests PINPOINT TEST A: FUEL LEVEL READS INACCURATELY

More information

HLY-3016 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO (weather and vibration resistant for exposed environments)

HLY-3016 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO (weather and vibration resistant for exposed environments) HLY-3016 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO (weather and vibration resistant for exposed environments) *To avoid damage to motorcycle, please see Speedometer, Tachometer, and Status and Warning Indicators

More information

Series II ODYR/SLX-01-1-C PERFORMANCE SPEEDOMETER

Series II ODYR/SLX-01-1-C PERFORMANCE SPEEDOMETER Series II ODYR/SLX-01-1-C PERFORMANCE SPEEDOMETER MOUNTING: The gauge requires a round hole 3-3/8 in diameter. It should be inserted into the opening from the front and the U-clamp will be installed from

More information

S-Series Combine and Front End Equipment Optimization

S-Series Combine and Front End Equipment Optimization S-Series Combine and Front End Equipment Optimization Ready To Harvest Yield Accuracy John Deere Harvester Works Preface This information is intended to help you understand how the Yield Monitor /Mapping

More information

Table No. 1 provides a means of identifying the various alternator systems. Note: All output figures are rated at 3600 RPM. TABLE NO.

Table No. 1 provides a means of identifying the various alternator systems. Note: All output figures are rated at 3600 RPM. TABLE NO. The alternator systems installed on Briggs & Stratton Intek OHV-Twin Cylinder Engines can easily be identified by the color of the stator output wires and the connector. Table No. 1 provides a means of

More information

Page 1 of 1 ALTERNATORS. Overview. Intek TM V-Twin Cylinder OHV Engine Service Manual Version 1.0. Copyright 1999 by Briggs and Stratton Corporation

Page 1 of 1 ALTERNATORS. Overview. Intek TM V-Twin Cylinder OHV Engine Service Manual Version 1.0. Copyright 1999 by Briggs and Stratton Corporation Overview Alternator Identification Page 1 of 3 The alternator systems installed on Briggs & Stratton Intek V-Twin Cylinder OHV Engines can easily be identified by the color of the stator output wires and

More information

Servo and Proportional Valves

Servo and Proportional Valves Servo and Proportional Valves Servo and proportional valves are used to precisely control the position or speed of an actuator. The valves are different internally but perform the same function. A servo

More information

CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS

CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS ZG CHARGING SYSTEM 8C - 1 CHARGING SYSTEM CONTENTS page GENERAL INFORMATION OVERVIEW... 1 DESCRIPTION AND OPERATION BATTERY TEMPERATURE SENSOR... 2 CHARGING SYSTEM OPERATION... 1 ELECTRONIC VOLTAGE REGULATOR...

More information

RODIX, INC. FC-40-PLC Plus Series Control Troubleshooting Guide for Circuit Board P/Ns and

RODIX, INC. FC-40-PLC Plus Series Control Troubleshooting Guide for Circuit Board P/Ns and RODIX, INC. FC-40-PLC Plus Series Control Troubleshooting Guide for Circuit Board P/Ns 24-488 and 24-489 Control must be connected to a known GOOD LOAD prior to testing Problem: No output from the control

More information

ODY-01-1 or ODY-01-2 SPEEDOMETER

ODY-01-1 or ODY-01-2 SPEEDOMETER ODY-01-1 or ODY-01-2 SPEEDOMETER Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several unique features and

More information

9/02 Kwikee Products Co. Inc. Kwikee # Electric Steps. Equipped with a Permanent Magnet Motor

9/02 Kwikee Products Co. Inc. Kwikee # Electric Steps. Equipped with a Permanent Magnet Motor Owner's Manual #880 9/02 Kwikee Products Co. Inc. Kwikee #1422257 Electric Steps Equipped with a Permanent Magnet Motor (For steps with Control Units 909506000, 909507000, or 909508000 and steps without

More information

Alternator Removal and Installation Instructions

Alternator Removal and Installation Instructions Alternator Removal and Installation Instructions Removal CAUTION: Always use care when working on your vehicle! Do NOT disconnect any electrical cables or wiring while the engine is running! Make sure

More information

INSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6003 Year Series:

INSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6003 Year Series: INSTALLATION GUIDE Chevrolet Digital Dash Panel Part Number: DP6003 Year Series: 1967-1972 * Disconnect the battery before attempting any electrical work on your vehicle. * KIT COMPONENTS One (1) Digital

More information

DEFOGGER SYSTEM PARTS LOCATION

DEFOGGER SYSTEM PARTS LOCATION BE61 PARTS LOCATION TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the malfunction are shown in the order of their probability.

More information

Superlift TruSpeed Speed Sensor Calibrator For Most Ford Trucks and SUVs 1992-Present INSTALLATION INSTRUCTIONS

Superlift TruSpeed Speed Sensor Calibrator For Most Ford Trucks and SUVs 1992-Present INSTALLATION INSTRUCTIONS FORM #33001.06-121703 PRINTED IN U.S.A. PAGE 1 OF 11 INTRODUCTION Superlift TruSpeed Speed Sensor Calibrator For Most Ford Trucks and SUVs 1992-Present INSTALLATION INSTRUCTIONS SUPERLIFT SUSPENSION SYSTEMS

More information

BE 30 BODY ELECTRICAL SYSTEM. Combination Meter COMBINATION METER. Parts Location

BE 30 BODY ELECTRICAL SYSTEM. Combination Meter COMBINATION METER. Parts Location BE30 BODY ELECTRICAL SYSTEM COMBINATION METER Parts Location BODY ELECTRICAL SYSTEM BE31 Meter Circuit (w/o Tachometer) No. 2 7 9 12 1 2 3 5 7 9 3 Wiring connector side ETC Pattern select switch A/T Oil

More information

NEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS

NEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS NEW VINTAGE INSTRUMENT AND GAUGE KIT INSTALLATION INSTRUCTIONS REV.01-033113 INDEX THE BASICS CLUSTER INSTALLATION TACHOMETER OPERATION SPEEDOMETER OPERATION TROUBLESHOOTING WIRING DIAGRAM pg.2 pg. 2 pg.

More information

EG3000. Generator Electronic Governor Controller Operation Manual

EG3000. Generator Electronic Governor Controller Operation Manual EG3000 Generator Electronic Governor Controller Operation Manual Smoke Limit Control, Idle Speed Control, suitable for Builtin, Non-Built-in and PT Pump Type Actuator. SP POWERWORLD LTD Willows, Waterside,

More information

GRAIN CART RETROFIT TRACK SLIDE-IN-HITCH SCALE SYSTEM

GRAIN CART RETROFIT TRACK SLIDE-IN-HITCH SCALE SYSTEM GRAIN CART RETROFIT TRACK SLIDE-IN-HITCH SCALE SYSTEM Instructions This manual is copyrighted by Scale-Tec. Redistribution or copy of this manual or portions of this manual must be approved through Scale-Tec

More information

Associated Procedures. Troubleshooting Steps SPECIFICATIONS. Check for multiple fault codes. STEP 1. Fault Code 283 or 284 inactive

Associated Procedures. Troubleshooting Steps SPECIFICATIONS. Check for multiple fault codes. STEP 1. Fault Code 283 or 284 inactive Associated Procedures Troubleshooting Steps STEPS SPECIFICATIONS STEP 1. Check for multiple fault codes. STEP 1A. Read faults. Fault Code 283 or 284 inactive STEP 2. Check the engine harness. STEP 2A.

More information

D - ADJUSTMENTS Nissan 240SX ENGINE COMPRESSION VALVE CLEARANCE IGNITION TIMING ENGINE PERFORMANCE On-Vehicle Adjustments

D - ADJUSTMENTS Nissan 240SX ENGINE COMPRESSION VALVE CLEARANCE IGNITION TIMING ENGINE PERFORMANCE On-Vehicle Adjustments D - ADJUSTMENTS 1990 Nissan 240SX 1990 ENGINE PERFORMANCE On-Vehicle Adjustments Nissan; Axxess, Stanza, 240SX ENGINE COMPRESSION 1) Start engine and warm to normal operating temperature. Disconnect distributor

More information

1994 Aerostar/Ranger/Explorer

1994 Aerostar/Ranger/Explorer http://www.fordtechservice.dealerconnection.com/pubs/content/~wsrk/~mus~len//... Section 13-01B: Instrument Cluster, Conventional DIAGNOSIS AND TESTING 1994 Aerostar/Ranger/Explorer Workshop Manual Pinpoint

More information

EG1069X. Generator Electronic Governor Controller Operation Manual

EG1069X. Generator Electronic Governor Controller Operation Manual EG1069X Generator Electronic Governor Controller Operation Manual Smoke Limit Controller Compatible with Barber Colman Dyn1-1069X series *Use for reference purpose only and not a genuine Barber Colman

More information

Part Number DP6003 Chevy Truck Digital Dash YEARS 67-72

Part Number DP6003 Chevy Truck Digital Dash YEARS 67-72 Part Number DP6003 Chevy Truck Digital Dash YEARS 67-72 KIT COMPONENTS: One (1) Digital Circuit Board One (1) Smoked Acrylic See-Through Lens *Peel off protective covering from both sides of lens attached

More information

Viper 90R Dies After Shifting

Viper 90R Dies After Shifting 3/9/2005 Problem: Unit will not shift into gear or engine dies when shifting into gear. (1) i. Turn on the ignition switch. ii. Set selector switch to neutral (N) position. iii. Set stop switch to O position.

More information

INSTALLATION GUIDE Ford Mustang Digital Dash Panel Part Number: DP7009 Year Series:

INSTALLATION GUIDE Ford Mustang Digital Dash Panel Part Number: DP7009 Year Series: Made in America Lifetime Guarantee Thank you for purchasing this gauge panel from Intellitronix. We value our customers! INSTALLATION GUIDE Ford Mustang Digital Dash Panel Part Number: DP7009 Year Series:

More information

INSTRUMENT PANEL Volvo 960 * PLEASE READ THIS FIRST * DESCRIPTION & OPERATION TESTING ACCESSORIES/SAFETY EQUIPMENT Volvo Instrument Panel

INSTRUMENT PANEL Volvo 960 * PLEASE READ THIS FIRST * DESCRIPTION & OPERATION TESTING ACCESSORIES/SAFETY EQUIPMENT Volvo Instrument Panel INSTRUMENT PANEL 1994 Volvo 960 1994 ACCESSORIES/SAFETY EQUIPMENT Volvo Instrument Panel 960 * PLEASE READ THIS FIRST * WARNING: When working around steering column and before performing repairs, disconnect

More information

MODEL MCV-7000 series SPEEDOMETER/TACHOMETER INFORMATION GAUGE Please read this before beginning installation or wiring.

MODEL MCV-7000 series SPEEDOMETER/TACHOMETER INFORMATION GAUGE Please read this before beginning installation or wiring. MODEL MCV-7000 series SPEEDOMETER/TACHOMETER INFORMATION GAUGE Please read this before beginning installation or wiring. IMPORTANT NOTE! This gauge has an odometer preset option that is only available

More information

VEHICLE SPEED CONTROL SYSTEM

VEHICLE SPEED CONTROL SYSTEM J VEHICLE SPEED CONTROL SYSTEM 8H - 1 VEHICLE SPEED CONTROL SYSTEM CONTENTS page DIAGNOSIS... 2 GENERAL INFORMATION... 1 page SERVICE PROCEDURES... 9 GENERAL INFORMATION The vehicle speed control system

More information

INFORMATION. covering use of Ammeter and Voltmeter ON and 1915 Model Six-54 Electrical System

INFORMATION. covering use of Ammeter and Voltmeter ON and 1915 Model Six-54 Electrical System INFORMATION covering use of Ammeter and Voltmeter ON- 1914 and 1915 Model Six-54 Electrical System Hudson Motor Car Company Detroit, Michigan, IX S. A USE OF AMMETER ON 1914 AND 1915 MODEL SIX-54 With

More information

Kwikee IMGL Step Control Testing Procedure #82-ST0500

Kwikee IMGL Step Control Testing Procedure #82-ST0500 Kwikee IMGL Step Control Testing Procedure #82-ST0500 TABLE OF CONTENTS Introduction 2 Resources Required 2 General Service Notes 3 Preparation 5 Troubleshooting and Test Procedures 5 Testing the Step

More information

CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM 1992 Infiniti G20 1991-92 SAFETY EQUIPMENT Infiniti Cruise Control Systems G20, M30, Q45 DESCRIPTION & OPERATION NOTE: For system component locations, see SYSTEM COMPONENT LOCATIONS.

More information

FUEL INJECTION SYSTEM - MULTI-POINT

FUEL INJECTION SYSTEM - MULTI-POINT FUEL INJECTION SYSTEM - MULTI-POINT 1988 Jeep Cherokee 1988 Electronic Fuel Injection JEEP MULTI-POINT 4.0L Cherokee, Comanche, Wagoneer DESCRIPTION The Multi-Point Electronic Fuel Injection (EFI) system

More information

WIPER/WASHER SYSTEM - FRONT ACCESSORIES & EQUIPMENT General Motors Corp. - Front Wiper/Washer System

WIPER/WASHER SYSTEM - FRONT ACCESSORIES & EQUIPMENT General Motors Corp. - Front Wiper/Washer System WIPER/WASHER SYSTEM - FRONT 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Front Wiper/Washer System DESCRIPTION & OPERATION CAUTION: To prevent scratching, wet the windshield before turning on wipers.

More information

Identify and understand the key components to the starting and charging system. Rotating Electrical Troubleshooting Guide. Battery.

Identify and understand the key components to the starting and charging system. Rotating Electrical Troubleshooting Guide. Battery. Rotating Electrical Troubleshooting Guide Battery Alternator Identify and understand the key components to the starting and charging system. Starter Motor TRUE SPECIALISTS CHOOSE EFEL 1 Efel_Trouble_Shooting_Guide_ENG_2016.indd

More information

GENERAL <ELECTRICAL>

GENERAL <ELECTRICAL> 00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................................. 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION

More information

1995 Jeep Grand Cherokee Limited. CRUISE CONTROL SYSTEM' '1995 ACCESSORIES & SAFETY EQUIPMENT Chrysler Corp. Cruise Control Systems

1995 Jeep Grand Cherokee Limited. CRUISE CONTROL SYSTEM' '1995 ACCESSORIES & SAFETY EQUIPMENT Chrysler Corp. Cruise Control Systems TROUBLE SHOOTING NO CRUISE CONTROL WHEN SET BUTTON IS PRESSED & RELEASED Check for: blown fuse, no vacuum at servo and/or defective servo, disconnected speed control cable, brakelight switch out of adjustment,

More information

1999 Dodge Durango ENGINE PERFORMANCE' 'Self-Diagnostics - Durango

1999 Dodge Durango ENGINE PERFORMANCE' 'Self-Diagnostics - Durango DTC P0320: NO CRANK REFERENCE SIGNAL AT PCM For connector terminal identification, see CONNECTOR IDENTIFICATION. For circuit identification and wiring diagram, see DURANGO wiring diagram in WIRING DIAGRAMS

More information

CAUTION Fuel Lift Pump. Initial Check. Resistance Check. https://qsol2.cummins.com/qs2/pubsys2/xml/en/procedures/10/

CAUTION Fuel Lift Pump. Initial Check. Resistance Check. https://qsol2.cummins.com/qs2/pubsys2/xml/en/procedures/10/ Page 1 of 16 View Related Topic 005-045 Fuel Lift Pump Initial Check Inspect the engine harness, the lift pump power connector, the lift pump relay power connector and the lift pump relay pins for the

More information

MCL-30K-SPD IMPORTANT NOTE!

MCL-30K-SPD IMPORTANT NOTE! MCL-30K-SPD Thank you for purchasing the Dakota Digital MCL-30K-SPD gauge for your Harley Davidson Touring bike. This is designed to be a replacement for all touring models from 1996 2003. This is part

More information

Check the wires going to the back of the computer, if the wires are secure and console will not start see step b.

Check the wires going to the back of the computer, if the wires are secure and console will not start see step b. ELECTRONIC TROUBLESHOOTING 1. PROBLEM: Console LED's will not light, console will not power up The bike must be pedaled at greater than 50 RPM while Check the wires going to the back of the computer, if

More information

Tachometers and Tach/Hourmeters AT and ATH Series

Tachometers and Tach/Hourmeters AT and ATH Series Tachometers and Tach/Hourmeters AT and ATH Series Installation Instructions 00-02-0986 Section 70 IMPORTANT! These instructions are specific to tachometer models with a single calibration push button.

More information

VACUUM FLUORESCENT DIGITAL DASHBOARD. The latest in digital dashboard technology for the street rodder, car, and truck enthusiast.

VACUUM FLUORESCENT DIGITAL DASHBOARD. The latest in digital dashboard technology for the street rodder, car, and truck enthusiast. SERIES 3 VACUUM FLUORESCENT DIGITAL DASHBOARD The latest in digital dashboard technology for the street rodder, car, and truck enthusiast. INSTALLATION AND OPERATION MANUAL Please read this before beginning

More information

CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM 1988 Jeep Cherokee 1988 Cruise Control Systems JEEP CRUISE COMMAND All Models DESCRIPTION & OPERATION Jeep vehicles use an electro-mechanical servo system. The system consists of

More information

Replacement Tach Board Manual

Replacement Tach Board Manual Replacement Tach Board Manual 67-74 Dodge and Plymouth Cars that use electronics Internal to the tachometer. Real Time Engineering 19352 Hilton Rd. Springdale, AR 72764 (479) 756-3917 fax Rev8 www.rt-eng.com

More information

ALTERNATOR - HITACHI

ALTERNATOR - HITACHI ALTERNATOR - HITACHI 1986 Isuzu Trooper II 1986 Alternators & Regulators HITACHI ALTERNATORS Isuzu DESCRIPTION Hitachi alternators are conventional 3-phase, self-rectifying alternators. Three positive

More information

Tension Control System MCS-166, MCS-203, MCS-204

Tension Control System MCS-166, MCS-203, MCS-204 Tension Control System MCS-166, MCS-203, MCS-204 P-257-WE 819-9027 Installation & Operation Instructions An Altra Industrial Motion Company Table of Contents Introduction...3 Specifications... 3-4 Installation

More information

GENERAL <ELECTRICAL>

GENERAL <ELECTRICAL> 00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................... 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION FOR DIAGNOSIS.......

More information

INSTRUMENT PANEL Toyota Celica DESCRIPTION & OPERATION GAUGES SWITCHES TESTING - GAUGES FUEL GAUGE & WARNING LIGHT

INSTRUMENT PANEL Toyota Celica DESCRIPTION & OPERATION GAUGES SWITCHES TESTING - GAUGES FUEL GAUGE & WARNING LIGHT INSTRUMENT PANEL 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Instrument Panel Celica * PLEASE READ THIS FIRST * WARNING: Vehicles are equipped with a driver-side

More information

INSTALLATION GUIDE Chevrolet Monte Carlo Dash Panel Part Number: DP9002 Year Series:

INSTALLATION GUIDE Chevrolet Monte Carlo Dash Panel Part Number: DP9002 Year Series: Made in America Lifetime Guarantee Thank you for purchasing this instrument from Intellitronix. We value our customers! INSTALLATION GUIDE Chevrolet Monte Carlo Dash Panel Part Number: DP9002 Year Series:

More information

EG1065X. Compatible with Barber Colman* Dyn1-1065X series * Use for reference purpose only and not a genuine Barber Colman product.

EG1065X. Compatible with Barber Colman* Dyn1-1065X series * Use for reference purpose only and not a genuine Barber Colman product. EG1065X Generator Electronic Governor Controller Operation Manual Compatible with Barber Colman* Dyn1-1065X series * Use for reference purpose only and not a genuine Barber Colman product. Headquarters

More information

MCL-30K-TCH. Remove nuts/screws and clamp to remove factory gauges 1 MAN#650336

MCL-30K-TCH. Remove nuts/screws and clamp to remove factory gauges 1 MAN#650336 MCL-30K-TCH Thank you for purchasing the Dakota Digital MCL-30K-TCH gauge for your Harley Davidson Touring bike. This kit is designed to be a replacement for all touring models, from 1996 2003. This is

More information

KWIKEE #888 ELECTRIC STEP. Owner's Manual ( )

KWIKEE #888 ELECTRIC STEP. Owner's Manual ( ) KWIKEE #888 ELECTRIC STEP Owner's Manual (1422279) TABLE OF CONTENTS Safety Information 2 Motor Assembly Identification 3 Product Information 4 Steps With Control Unit 4 Steps Without Control Unit 4 General

More information

Page 1 of 6 NO START - ENGINE CRANKS OKAY General Inspection 1. Ensure proper starting procedure is being used. 2. Visually check vacuum hoses for splits, kinks and improper connections. See underhood

More information

ION-01-6 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO

ION-01-6 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO ION-01-6 PERFORMANCE SPEEDOMETER/TACHOMETER COMBO MOUNTING: It should be inserted into the opening from the front and the L-clamps will be installed from the back. Tighten the nuts on the L-clamps so that

More information

4.0L CEC SYSTEM Jeep Cherokee DESCRIPTION OPERATION FUEL CONTROL DATA SENSORS & SWITCHES

4.0L CEC SYSTEM Jeep Cherokee DESCRIPTION OPERATION FUEL CONTROL DATA SENSORS & SWITCHES 4.0L CEC SYSTEM 1988 Jeep Cherokee 1988 COMPUTERIZED ENGINE Controls ENGINE CONTROL SYSTEM JEEP 4.0L MPFI 6-CYLINDER Cherokee, Comanche & Wagoneer DESCRIPTION The 4.0L engine control system controls engine

More information

HORN OPERATION DIAGNOSIS MOST GM VEHICLES 1967 AND UP

HORN OPERATION DIAGNOSIS MOST GM VEHICLES 1967 AND UP Revised: 27OC2010 HORN OPERATION DIAGNOSIS MOST GM VEHICLES 1967 AND UP All General Motors vehicles (from the 60s through the 80s) have a horn or horns that operate on the same basic principle. When you

More information

1 of 16 1/10/2015 7:25 AM STARTER MOTOR 2009 Hyundai Accent 1.6L Eng GS REQUESTED INFORMATION DISASSEMBLY 1. Disconnect the M-terminal (A) on the magnet switch assembly (B). Fig 1: Identifying M-Terminal

More information

Electric Brakes. Braking Systems - Electric

Electric Brakes. Braking Systems - Electric Electric Brakes The electric brakes on your trailer are similar to the drum brakes on your automobile. The basic difference is that your automotive brakes are actuated by hydraulic pressure while your

More information

BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines

BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines BSR BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines Features Digital Advance The main feature of the Magic Box is the digital advance that replaces conventional weights and springs.

More information

Return to Main Table of Contents GENERAL... 2 IGNITION SYSTEM... 4 CHARGING SYSTEM STARTING SYSTEM CRUISE CONTROL SYSTEM...

Return to Main Table of Contents GENERAL... 2 IGNITION SYSTEM... 4 CHARGING SYSTEM STARTING SYSTEM CRUISE CONTROL SYSTEM... ENGINE ELECTRICAL SYSTEM Return to Main Table of Contents GENERAL... 2 IGNITION SYSTEM... 4 CHARGING SYSTEM... 13 STARTING SYSTEM... 29 CRUISE CONTROL SYSTEM... 38 27-2 GENERAL GENERAL SPECIFICATIONS Distributor

More information

The ignition coil for the vehicles covered by this guide is in the following locations:

The ignition coil for the vehicles covered by this guide is in the following locations: Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: 1989-92 engines: mounted to the firewall 1993-96 2.5L engines: mounted

More information

GRAIN CART RETROFIT J-M TRACK SLIDE IN HITCH SCALE SYSTEM

GRAIN CART RETROFIT J-M TRACK SLIDE IN HITCH SCALE SYSTEM GRAIN CART RETROFIT J-M TRACK SLIDE IN HITCH SCALE SYSTEM Instructions This manual is copyrighted by Scale-Tec. Redistribution or copy of this manual or portions of this manual must be approved through

More information

1.5L L

1.5L L Selected Block IGNITION TIMING NOTE: Perform all adjustments with engine at normal operating temperature, cooling fan and accessories off, transmission in Park or Neutral, and front wheels in straight-ahead

More information

Unit 10 Measuring Instruments

Unit 10 Measuring Instruments Objectives: Unit 10 Discuss the operation of a d Arsonval meter movement. Connect a voltmeter to a circuit. Read an analog multimeter. Connect an ammeter. Measure resistance using an ohmmeter. Analog meters

More information

Troubleshooting The Transmission Hydraulic System

Troubleshooting The Transmission Hydraulic System 416B, 426B, 428B, 436B, & 438B BACKHOE LOADERS TRANSMISSION Testing And Adjusting Troubleshooting The Transmission Hydraulic System Make reference to the following warning and pressure tap locations for

More information

Gear indicator models. GearTronic GT3000. Gear Indicators F.A.Q. & Troubleshooting v1.0 28/03/2017

Gear indicator models. GearTronic GT3000. Gear Indicators F.A.Q. & Troubleshooting v1.0 28/03/2017 Gear Indicators 2017 F.A.Q. & Troubleshooting v1.0 28/03/2017 Gear indicator models GearTronic GT3000... 1 GearTronic² GT400... 2 GearTronic ZERO GT3100-D1, GT3100-D4, GT3100-D5...3 GearTronic ZERO GT310-D2...

More information

MONITOR INSTALLATION AND OPERATING INSTRUCTIONS VERSION

MONITOR INSTALLATION AND OPERATING INSTRUCTIONS VERSION 2200 Simplicity 3x 2200 SURVEILLANCE SIMPLICITY 3x AIRSEEDER MONITOR INSTALLATION AND OPERATING INSTRUCTIONS VERSION 1.00 2200 Surveillance Simplicity Air Seeder Page 2 CONTENTS 1.0 INSTALLATION... 3 1.1

More information

Media Number -SENR Publication Date -01/10/1977 Date Updated -12/10/2001

Media Number -SENR Publication Date -01/10/1977 Date Updated -12/10/2001 - - 55, 56, 57, 58 & 59 TOWING WINCHES Page 1 of 21 Testing and Adjusting 55, 56, 57, 58 & 59 TOWING WINCHES Media Number -SENR7217-01 Publication Date -01/10/1977 Date Updated -12/10/2001 Testing And

More information

ANTI-LOCK BRAKING SYSTEM (ABS)

ANTI-LOCK BRAKING SYSTEM (ABS) 35B-1 GROUP 35B ANTI-LOCK BRAKING SYSTEM (ABS) CONTENTS GENERAL DESCRIPTION......... 35B-2 ANTI-SKID BRAKING SYSTEM (ABS) DIAGNOSIS.................... 35B-3 INTRODUCTION TO ANTI-LOCK BRAKE SYSTEM DIAGNOSIS................

More information

MODEL MCL-2002 TANK MOUNT SPEEDOMETER/TACHOMETER

MODEL MCL-2002 TANK MOUNT SPEEDOMETER/TACHOMETER MODEL MCL-2002 TANK MOUNT SPEEDOMETER/TACHOMETER *To avoid damage to motorcycle, please see Speedometer, Tachometer, and Status and Warning Indicators sections for details on locating VSS, Tachometer,

More information

Alternator, Leece-Neville 15.00

Alternator, Leece-Neville 15.00 Alternator, Leece-Neville 5.00 General Information General Description The Leece-Neville JB series alternator is a 4-volt self-load-limiting alternator equipped with a threestep adjustable voltage regulator.

More information

STARTER - HITACHI Isuzu Trooper II DESCRIPTION TESTING STARTER PERFORMANCE TESTS Starters HITACHI. Isuzu

STARTER - HITACHI Isuzu Trooper II DESCRIPTION TESTING STARTER PERFORMANCE TESTS Starters HITACHI. Isuzu STARTER - HITACHI 1986 Trooper II 1984 Starters HITACHI DESCRIPTION Starter is a conventional 12-volt, 4-pole brush-type motor, with direct or reduction gear drive. The starter-mounted solenoid shifts

More information

ELECTRICAL. Contents - Wiring Diagrams

ELECTRICAL. Contents - Wiring Diagrams Contents - Wiring Diagrams T-Bar (Floating Deck - Hydro)............................................ 8-16 T-Bar (Fixed Deck - Gear)............................................... 8-17 T-Bar (Fixed Deck

More information

Service Guide. Service Guide LEVEL BEST. June How to use the Service Guide:

Service Guide. Service Guide LEVEL BEST. June How to use the Service Guide: Service Guide June 2003 The Level Best Service Guide has been organized to facilitate quick and easy diagnostics and trouble shooting for the most common installation problems and serviceable part failures.

More information

Commander IS0128 ISO128E ECR# /04. Tachometer/ Engine Hourmeter

Commander IS0128 ISO128E ECR# /04. Tachometer/ Engine Hourmeter Commander Tachometer/ Engine Hourmeter Analog Tachometer Digitally displays Hours Engine Has Been Run Fuel Level Other Features if Available: Fuel anagement Fuel Flow in GPH or LPH Total or Trip Fuel Used

More information

Chevrolet. Installation Manual

Chevrolet. Installation Manual 1959 1960 Chevrolet Installation Manual TABLE OF CONTENTS Welcome from the Team at Classic Instruments!... 3 Mount Adapter Ring... 4 Mount New 4-5/8 Gauge in Center Gauge Pod... 4 Mount New 2-1/8 Gauges

More information

ENGINE ELECTRICAL SYSTEM Return To Main Table of Contents

ENGINE ELECTRICAL SYSTEM Return To Main Table of Contents ENGINE ELECTRICAL SYSTEM Return To Main Table of Contents GENERAL... 2 CHARGING SYSTEM... 4 STARTING SYSTEM... 23 IGNITION SYSTEM... 32 AUTOMATIC SPEED CONTROL (CRUISE) SYSTEM... 43 GENERAL GENERAL SPECIFICATIONS

More information

Tachometer (RPM Feedback) General

Tachometer (RPM Feedback) General Tachometer (RPM Feedback) General The force of magnetic fields interacting drives all electric motors. How the magnetic field is created on the moving rotor determines the type of control required on the

More information