Type 120 solenoid WHITE-RODGERS DC PRODUCTS FEATURES

Transcription

1 WHITE-RODGERS D PRODUTS Type 0 solenoid FETURES Water resistant apable of handling low and high current requirements Versatile mounting and termination ENGINEERING DT ontacts Pole form SPNO Material silver alloy or copper Termination 5 / UNF-2 thread or 1 / 4-20 UN-2 thread Volts D VD VD 36 VD ont RTINGS Inrush onsult factory for additional ratings. Elec. Life 10,000 50,000 25,000 oils Voltage 6 VD through 48 VD Termination #8-32 UN-2, #10-32 UNF-2 thread or 1 / 4 quick-connect Power (approximate) ontinuous 8.1 watts Intermittent.4 watts onnections 1. oil isolated (two terminals) 2. One coil lead grounded to bracket (one terminal) Operate (77 F/25 ) 67% of nominal (Int.) 75% of nominal (ont.) 110% max. safe of nominal coil voltage ontact Material opper Silver lloy Silver lloy GENERL DT Dielectric Strength 500 Volts Temperature Range -20 F to 150 F (-28.9 to 65.6 ) (Intermittent) -20 F to 0 F (-28.9 to 48.9 ) (ontinuous) Mechanical Life (no load) 100,000 cycles Mounting Position Recommended mounting is coil terminals up or horizontal Weight (approximate) SPNO 6.0 oz. Duty ycle ontinuous Intermittent 30 seconds on maximum and minimum 6 minutes off Hardware Torque Specification ontact Terminal: inch-lbs. oil Terminal: -18 inch-lbs. Volts D Intermittent OIL DT Resistance in Ohms SPEIL OILS VILLE UPON REQUEST ontinuous St. Louis, Missouri Markham, Ontario The Emerson logo is a trademark and a service mark of Emerson Electric o. R

2 TYPE 0 PRT NUMERING SYSTEM 0 1 xx x x x - x asic Part Number Series SPNO oil Voltage/Duty 02 6 Volt continuous 05 Volt continuous 06 Volt intermittent 07 Volt continuous Volt continuous 24 Volt continuous Volt continuous (special, 100 ohm coil) Volt continuous Volt continuous oil Termination (15 in-lb torque spec.) 1 Isolated w/ #10-32 terminal (0.220 min. length) 2 Grounded w/ #10-32 terminal (0.220 min. length) 3 Isolated w/ 1/ 4 Q.. terminal 4 Grounded w/ 1/ 4 Q.. terminal 6 Grounded w/ #8-32 tapered terminal 7 Isolated w/ #10-32 terminal (0.451 min. length) 8 Grounded w/ #10-32 terminal (0.451 min. length) Mounting racket 1 Standard bracket 2 L shaped bracket ontact Material and Termination (55 in-lb torque spec.) 1 gdo w/ 5 / terminal (0.388 min. length) 3 u w/ 5 / terminal (0.388 min. length) 4 u w/ 1 / 4-20 terminal 5 gdo w/ 5 / terminal (0.495 min. length) Factory ssigned Specials (where undefined, contact factory) No dash Standard assembly, hardware sent bulk 1 Without hardware 2 Extra hardware loosely mounted to solenoid 4 ustomer requested 5 Mounting bracket zincplated and dichromate dip 6 ustomer requested 7 ustomer requested 8 No hardware, mounting bracket as -5 option 9 ustomer requested 11 ustomer requested PPLITION NOTES Not all part number combinations are available. Please contact your Sales Representative for available part numbers. Solenoids applied in battery charging circuits should be protected from higher than rated voltage during charging. The service life may be affected by this condition and the solenoid may or may not operate the circuit as intended. ircuits should be designed to provide safe operation should the solenoid fail in either the open or closed position. back-up wrench must be used to hold the bottom nut stationary during installation. Terminal Type 4 - Isolated oil (STD racket) L 2.5 H MX See Part Numbering System chart, above W WIDE X.400 LONG SLOT #10-32 UNF-2 THRED TYP. 5/16-24 UNF-2 THRED TYP. IRUIT DIGRM Terminal Type 4 - Isolated oil (L racket) L H MX /16-24 UNF-2 THD (2 PLES) See Part Numbering System chart, above #10-32 UNF-2 THD (PLES) W WIDE X.400 LONG SLOT IRUIT DIGRM R

3 D POWER ONTTORS SPNO Type 70 SPNO WRNING FIRE HZRD Must be installed in a dry and protected place. Failure to protect solenoid from water and other contaminants could result in Fire, Property Damage, Serious Personal Injury, or Death. TYPE 70 SPNO Single Pole Normally Open ontact ase is Dust Resistant and Isolated from Ground SPEIFITIONS Dimensions L x 3.48 W x 2.40 H Weight oz. Temperature Range to +2 F Terminations, ontacts /16-24 UNF-2 thread Terminations, oil #10-32 UNF-2 thread Recommended Mounting Plunger vertical with cap down Hardware Torque, ontact Terminal in. lbs. Hardware Torque, oil Terminal in. lbs. aution: back-up wrench must be used to hold the bottom nut stationary. gency U.L. 538 Recognized, File U2138 oil oil ontact Rating (mps) Inductive Load Model Duty Terminal Pole racket Voltage Resistance ontact Voltage Normally Open Normally losed Number ycle ➂ Type ➀ Form Style D.. (Ohms) ➁ Material D.. ontinuous Inrush ontinuous Inrush ontinuous 3 SPNO Standard 16 opper ontinuous 4 SPNO Standard 16 opper ontinuous 4 SPNO Standard opper ontinuous 4 SPNO Standard 36 1 opper ➀ 3 = oil Grounded to ase 4 = Isolated oil ➁ oil resistance in 25 ➂ Intermittent duty designs available. Type 0 SPNO TYPE 0 SPNO Single Pole Normally Open ontact, Dust Resistant, Water Resistant and ase is Isolated from racket SPEIFITIONS Dimensions L x 2.88 W x 3.09 H (Std. racket) Dimensions L x 3.00 W x 3.03 H (L-Shaped racket) Weight oz. Temperature Range, Intermittent Duty to +150 F Temperature Range, ontinuous Duty to +0 F Terminations, ontacts /16-24 studs,.495 min. length Terminations, oil #10-32,.451 min. length Recommended Mounting oil terminals up or horizontal Hardware Torque, ontact Terminal in. lbs. Hardware Torque, oil Terminal in. lbs. aution: back-up wrench must be used to hold the bottom nut stationary. oil oil ontact Rating (mps) Inductive Load Model Duty Terminal Pole racket Voltage Resistance ontact Voltage Normally Open Number ycle ➀ Type ➁ Form Style D.. (Ohms) ➂ Material D.. ontinuous Inrush ➃ ontinuous 4 SPNO Standard 16.0 Silver lloy ontinuous 3 SPNO Standard ➄ 16.0 Silver lloy Intermittent 4 SPNO Standard 6.0 opper Intermittent 4 SPNO L 6.0 opper ontinuous 4 SPNO L 26.0 Silver lloy ➀ Intermittent Duty ycle = 30 seconds ON maximum and 6 minutes OFF ➁ 4 = Isolated oil ➂ oil resistance in 25 ➃ Inrush urrent: urrent applied within the fi rst 1/2 second of contact closure ➄ oil grounded to bracket NOTE: UTION must be used in coil selection for use in volt sytems where battery charging may expose coil to continuous, higher-than-rated voltage. volt coils are recommended. White-Rodgers will not be responsible for consequences of misapplied solenoids. 119a

4 TYPE 0 D.. POWER ONTTOR SERVIE INSTRUTIONS ONTTEUR.. INSTRUTIONS D'ENTRETIEN ONTTOR ON ENERGÍ DE ORRIENTE ONTINU INSTRUIONES DE SERVIIO! WRNING To prevent electrical shock and/or equipment damage, disconnect electric power to system at main fuse or circuit breaker box until installation is complete. WRNING Pour éviter les risques d électrocution et/ou de dégâts de l équipement, il faut débrancher l alimentation électrique du système au fusible ou au coupe-circuit principal jusqu à la fin de l intervention.!! WRNING Para evitar el choque eléctrico y/o el daño en el equipo, desconecte la energía eléctrica que va al sistema en el fusible principal o en la caja de interruptores de circuito, hasta que se haya completado la instalación. SPEIFITIONS: Insulated oil Terminals Preferred Mounting Position oil Terminals Up RTÉRISTIQUES: ornes Isolées De obine Position De Montage Privilégiée - ornes De obine Excitées ESPEIFIIONES: Terminales De La obina islados Posición De Montaje Preferida - Terminales De La obina rriba Voltage (VD Max.) Tension (Vc.c. maxi.) Voltage (VD max.) oil obine obina ontact ontact ontacto Duty ycle / ycle de service / iclos de Servicio ontinuous / ontinu / ontinuo ontinuous / ontinu / ontinuo Intermittent / Intermittent / Intermitente Intermittent / Intermittent / Intermitente ontinuous / ontinu / ontinuo Fig. 1 Single Pole Normally Open (Isolated oil) Interrupteur Unipolaire De Travail (obine Isolée) Unipolar Normalmente bierto (obina Separada) Wiring Diagram (Terminal Identification) oil N.O. ontacts Schéma De âblage (Identification Des ornes) obine ontacts De Travail Diagrama De ableado (Identificación De Terminales) obina ontactos Normalmente biertos WHITE-RODGERS EMERSON ELETRI O REVIS ROD ST. LOUIS, MISSOURI PRT NO./No. DE PIÈE/No. DE PRTE

5 When used to replace contactors having only one coil terminal (per fig. 2), reconnect either terminal per fig. 3 or 4 as indicated by dotted line, depending on original circuit. En cas d'utilisation pour remplacer des contacteurs à une seule borne de bobine comme sur la fig. 2 - reconnecter l'une ou l'autre des bornes comme sur la fig. 3 ou 4 - comme indiqué par la ligne en pointillés - suivant le circuit d'origine. uando se usa para reemplazar contactores que tienen solo un terminal de bobina segun la fig. 2 - vuelva a conectar cualquier terminal de bobina segun la fig. 3 o 4 - tal como se indica con la línea de puntos - dependiendo del circuito original. Ground one coil terminal per dotted line. Mettre une borne de bobine à la terre comme indiqué par la ligne en pointillés. onecte a tierra un terminal de la bobina segun la línea de puntos. onnect one coil terminal to line (or battery) N. O. power terminal per dotted line. Raccorder une borne de bobine au secteur (ou à la batterie) borne alimentation Norm. Ouv. comme indiqué par la ligne en pointillés. onecte un terminal de la bobina al terminal de energía normalmente abierto de la línea (o batería), segun la línea de puntos. Fig. 2 Three Terminal ontactor ontacteur À Trois ornes ontactor De Tres Terminales Fig. 3 Grounded oil obine Mise À La Terre obina onectada Tierra Fig. 4 oil ommon to Line (or attery) Liaison Ligne ommune De obine / Secteur (Ou atterie) obina omún Para La Línea (O atería) PPLITION NOTES ontactors applied in battery charging circuits should be protected from higher than rated voltage during charging. The service life may be affected by this condition and the contactor may not operate the circuit as intended. ircuits should be designed to provide safe operation should the contactor fail in either the open or closed position. backup wrench must be used to hold the bottom nut stationary during installation. REMRQUES Un contacteurs utilisé dans un circuit de recharge de piles doit être protégé contre toute tension supérieure à la valeur nominale pendant la recharge. Toute surtension risque de nuire à sa longévité et à son bon fonctionnement dans le circuit. oncevoir les circuits pour qu ils fonctionnent en toute sécurité si le solénoïde fait défaut, que ce soit en position ouverte ou fermée. Pendant l installation, utiliser une clé pour empêcher l écrou inférieur de tourner. NOTS DE PLIION Los contactores que son aplicados en circuitos cargados por medio de baterías deben ser protegidos del alto voltage durante su carga. El tiempo de servicio puede ser afectado por esta condicion y el solenoide podría o no operar el circuito deseado. Los circuitos deben ser diseñados para proveer seguridad durante su operación, si el solenoide fallara al estar abierto cerrado. Se deberá usar una llave como soporte para mantener la tuerca de la parte inferior fija durante la instalación.