ED50. Low energy automatic swing door operator. Service Manual

Size: px
Start display at page:

Download "ED50. Low energy automatic swing door operator. Service Manual"

Transcription

1 ED5 Low energy automatic swing door operator Service Manual DL EN

2 dormakaba ED5 Service Manual Table of Contents t Table of contents Table of contents General information Product description Safety information ED5 5. ED5 operator component views 5. Arm configurations 6. Header assembly 7 5 Recommended tools, tightening torque 7 5. Recommended tools 7 5. Standard tightening torque 7 6 User interface 8 6. Overview 8 6. button keypad and display 8 6. Program switch panel 9 6. Operator status LEDs 9 7 Terminal board accessory interfaces 7. ED5 terminal board accessory interfaces 8 ED5 door signage 8. Low energy operator 8. Low energy single swing door 8. Door signage, low energy double swing doors 9 Maintenance 9. Safety information label, low energy swinging doors 9. ED5 environment and cleaning 9. Yellow LED, service level 9. Pull arm maintenance Pull arm torque requirements Push arm maintenance Push arm torque requirements 6 Measure reveal depth, parameter rd 7. Reveal depth parameter rd 7. Measure and record reveal depth, rd value 7. rd parameter values 7 Operator spring tension 8. Set operator spring tension 8 Power fail closing speed 9. Set power fail closing speed 9 Perform learning cycle. Perform learning cycle Parameters. Parameters. Driving parameters detail 5 Troubleshooting 5. Information and error codes 5. Red LED status codes 5. Troubleshooting chart, "ln" codes 5 5. Troubleshooting chart, "E" codes 6 6 dormakaba handheld 8 6. dormakaba handheld terminal 8 6. dormakaba handheld; configuration parameters 9 6. dormakaba handheld; driving parameters 6. dormakaba handheld; special functions (Upgrade cards) ED5, Not used 6.5 dormakaba handheld; diagnostics 6.6 dormakaba handheld; firmware update 7 ANSI/BHMA standards 6 7. A56.9 Low energy power operated doors 6 ED5 DL6-6 -8

3 dormakaba ED5 Service Manual Chapters and General information. Service Manual This manual provides service information for ED5 low energy automatic swing door operators.. Manual storage This document must be kept in a secure place, and accessible for reference as required. If the door system should be transferred to another facility, insure that this document is transferred as well.. dormakaba.com website Manuals are available for review, download, and printing on dormakaba.com/us website.. Dimensions Unless otherwise specified, all dimensions are given in inches ( )..5 Symbols and labels used in these instructions WARNING This symbol warns of hazards which could result in personal injury or threat to health. NOTICE Draws attention to important information presented in this document..5 Symbols and labels used in these instructions WARNING CAUTION This symbol warns of a potentially unsafe procedure or situation. Electric shock hazard! TIPS AND RECOMMENDATIONS WARNING Hand pinch point and crushing hazards! Clarifies instructions or other information presented in this document. WARNING Crushing hazards! Product description. ED5 Intended use ED5 low energy automatic swing door operators are designed to be installed on an interior building surface. These operators are used for opening and closing interior or exterior swing doors. ED5 maximum door width of 8 inches at pounds. Fig.. ED5 header Header width Door frame width Fig.. ED5 operator ED5 DL6-6 -8

4 dormakaba ED5 Service Manual Chapter Safety information. Safety instructions This document contains important information for servicing ED5 low energy swing door operators. Review applicable information thoroughly prior to operator troubleshooting and maintenance.. Door signage requirements Proper signs and labels shall be applied and maintained on the door controlled by the ED5 swing door operator per ANSI/BHMA A56.9, Standard for power assist and low energy power operated doors, paragraph 8, ED5 door signage.. Safety warnings WARNING Hand pinch point and crushing hazards at door closing edges! WARNING Crushing hazards at door closing edges! WARNING Hazard to mechanical processes by use of control settings, elements, or procedures not documented in this manual! Secondary closing edge Opposing closing edge Main closing edge Fig.. Door closing edges WARNING Electric shock hazard! By use of control elements, settings, or procedures not documented in this manual! WARNING Hand pinch point and crushing hazards! Pull arm and track Push arm WARNING Work on electrical equipment and 5 Vac wiring must be performed only by qualified personnel! Fig.. Pull arm and track Fig.. Push arm ED5 DL6-6 -8

5 dormakaba ED5 Service Manual Chapter ED5. ED5 operator component views Fig... Power switch Vac cable Housing unit Drive axle connection 5 Operator (motor, ED5 component view one gear, spring) 6 Fig... ED5 terminal board detail 7 Spring tension 8 adjustment, closing force 8 button user 9 Information display interface Potentiometer, closing speed adjustment Terminal jumper socket, push or pull 5 mounting 5 RJ5 socket, double door operator synchronization 6 Com service connector Fig... ED5 control board detail 7 Accessories terminal board 8 Mounting plate 9 Customer ground terminal Guide pin Ribbon cable Ribbon cable socket 6 Upgrade card socket Motor 5 Encoder socket and cable 7 6 Motor socket and cable Control board 8 Motor brake 8 5 ED5 DL

6 dormakaba ED5 Service Manual Chapter Fig... ED5 component view two. Arm configurations Power switch Vac terminals Drive axle connection 6 Spring tension adjustment, closing force 9 Customer ground terminal Guide pin 9. Arm. Adjustment screw. Connecting rod. Shoe.5 Axle extension.6 Extended connecting rod Fig... Push arm kit Fig... Deep push arm kit.6 6 Fig... Pull arm kit. Arm. Track. Pivot pin. Slide shoe.5 Cover.6 CPD arm.7 CPD lever.... Fig... CPD pull arm kit ED5 DL6-6 -8

7 dormakaba ED5 Service Manual Chapters and 5. Header assembly Fig... ED5 header assembly Header Program switch panel Pull arm with track Access hole for spring tension 5 Recommended tools, tightening torque 5. Recommended tools T-handle hex key, 5 mm Hex keys,.5 mm, mm, 6 mm Screwdriver, flat blade Door pressure gauge, to 5 ft - lbf 5 Screwdriver, Phillips, # and # 6 Torque wrench, to 5 ft lb 6. 5 mm hex key socket 7 Open end wrench, mm 8 Screwdriver, flat blade., M (/6 to /") Fig. 7.. Recommended tools Standard tightening torque 5.. Standard tightening torque Fastener size ft lb N m M5.7 5 M M8 7 M M ED5 DL

8 dormakaba ED5 Service Manual 6 Chapter 6 User interface 6. Overview Fig. 6.. digit display button keypad button keypad and display 6. button keypad and display 6.. Operator user interfaces. button keypad and digit display. button keypad; to input and adjust door parameter values. digit display; parameter values, error and information codes. 6.. button keypad functions Fig. 6.. button keypad and display digit display button keypad. Right button Left button Access parameter menu, press button > seconds.. Edit selected parameter.. Save changed value.. Cancel parameter edit process.. Exit parameter menu, press button < s.. Both buttons together Acknowledge errors, press both buttons < s.. Reset, press both buttons > s.. Up button Scroll through parameters and error messages.. Increase parameter value.. Scroll through parameters and error messages.. Reduce parameter value.. Opening pulse, press button < s.. Down button Learning cycle, press button > s. 5. Reset with factory setting, press button > 8 s (program switch Close position). 6. Identify operator orientation for display. 8 ED5 DL6-6 -8

9 dormakaba ED5 Service Manual Chapter 6 6. Program switch panel 6.. Program switch door control modes Auto, door opens following pulse generation by a knowing act device or by push/pull. Close, door closes automatically, or remains closed. Open, door opens automatically and remains open. Fig. 6.. Program switch panel Program switch Program switch, Exit Only switch, panel position. position Comm port for dormakaba. 6.. Exit only switch modes Used when activation sensors are installed. handheld. 6. Operator status LEDs Fig. 6.. Operator status LEDs Red LED Yellow LED Green LED Power switch 6.. Operator status LEDs Header cover must be opened to view LEDs.. Red LED Blinking codes are used to indicate "ln " information (system status or operating conditions) or certain error codes "E ".. Yellow LED Maintenance interval indicator. When illuminated, an indication the operator system has to be serviced.. Green LED On, internal Vdc power is On. Off, internal Vdc power is Off. TIPS AND RECOMMENDATIONS Details on LED status codes and maintenance intervals can be found in Chapter 5, Troubleshooting. ED5 DL

10 dormakaba ED5 Installation Instructions Chapter 7 7 Terminal board accessory interfaces 7. ED5 terminal board accessory interfaces Green LED (Para. 6.) Yellow LED (Para. 6.) Red LED (Para. 6.) Key (red insert) location in socket. Assigned plug has tab broken off in same location. 5 Jumpers, factory installed at following terminals: and a 5 and * and * * Remove jumpers if safety sensors installed. 6 DCW upgrade card plug. Not used. 7 Fire protection upgrade card plug. Not used. Fig. 7.. Terminal board electrical connections B A 57 57a 5 7 X8 Night- Activation inputs bank Interior Exterior input Safety sensors DCW bus Swing side Approach side V + V X 8 - AC/DC + 5% Wet X Output 666 G + V X Signal input V + V V V Signal input V + V Signal input X5 Maximum current load:.5 A COM Locking relay N.O. Maximum current: N.C. A, 8 V DC/AC V Locking feedback contact Reference Note Test output V + V Signal input Test output V 5 5 VDC Class II X6 X9 X X a 5 V V Night-bank 8K resistor not required + V V Signal input V Partial Open Permanent Open Exit Only Automatic Off N.C. N.O. COM Emergency close Smoke detectors Night trigger Program, exit only switches Door status Note : Terminals and also used for swing side overhead presence sensor input when parameter ST is set to 7 or 8. Reference Chapter. ED5 DL6-6 -8

11 dormakaba ED5 Installation Instructions Chapter 8 8 ED5 door signage 8. Low energy operator 8.. Overview Signage and warnings are specified in ANSI /BHMA A56.9, American National Standard for power assist and low energy power operated doors. 8.. All low energy doors Fig. 8.. AUTOMATIC CAUTION DOOR decal 8. Low energy single swing door Fig. 8.. Low energy decals, knowing act device initiation of door operation. AUTOMATIC CAUTION DOOR decal. All low energy doors shall be marked with signage visible from both side of door with the words "AUTOMATIC CAUTION DOOR". Signs shall be mounted 5" ± " [7 mm ± 5 mm] from floor to centerline of sign. 5 ± 8.. Knowing act switch used to initiate door operation Fig. 8.. ACTIVATE SWITCH TO OPERATE decal, knowing act device. ACTIVATE SWITCH TO OPERATE decal. When a knowing act device is used to initiate operation of door operator, door shall be provided with sign on each side of door where switch is operated with message "ACTIVATE SWITCH TO OPERATE". "Activate Switch to Operate" sign located on side (s) of door where switch is located Fig. 8.. Low energy decals, push/pull initiation of door operation 8.. Push/Pull used to initiate door operation Fig. 8.. PUSH TO OPERATE, PULL TO OPERATE decals. PUSH TO OPERATE, PULL TO OPERATE decals. When push/pull is used to initiate operation of door operator, doors shall be provided with the message "PUSH TO OPERATE" on push side of door and "PULL TO OPERATE" on pull side of door. 5 ± ED5 DL6-6 -8

12 dormakaba ED5 Service Manual Chapter 8 8. Door signage, low energy double swing doors Fig. 8.. Knowing act, non-hinge side Fig ± 5 ± Fig. 8.. Push/pull, push to operate Fig. 8.. Double egress, RH, knowing act Fig ± Push/pull, pull to operate 5 ± 5 ± Fig Knowing act, hinge side Double egress, RH, knowing act 5 ± ED5 DL6-6 -8

13 dormakaba ED5 Service Manual Chapter 9 9 Maintenance 9. Safety information label, low energy swinging doors 9.. Low energy swinging door safety information label This AAADM label outlines safety checks that should be performed daily on low energy swinging door controlled by an ED5 operator. 9.. Safety information label location Place label in a protected, visible location on door frame, near operator power switch if possible. 9.. Annual compliance section of label This section of label is only completed on low energy swing doors that comply with ANSI/BHMA A56.9 standard and pass inspection by a AAADM certified dormakaba USA, Inc. technician. 9.. Additional annual compliance inspection labels Place additional labels over annual compliance inspection section of safety information label. Fig. 9.. Low energy safety information label SAFETY INFORMATION Low Energy Swinging Doors These minimum safety checks, in addition to those in the Owner s Manual, should be made each day and after any loss of electrical power.. Activate the door. Door should open at a slow smooth pace ( or more seconds), and stop without impact.. Door must remain fully open for a minimum of 5 seconds before beginning to close.. Door should close at a slow, smooth pace ( or more seconds), and stop without impact. Fig. 9.. Low energy annual compliance inspection label ANNUAL COMPLIANCE INSPECTION INSPECT FOR AND COMPLIES WITH ANSI A56.9 ON: DATE: by AAADM Certified Inspector Number:. Inspect the floor area. It should be clean with no loose parts that might cause user to trip or fall. Keep traffic path clear. 5. Inspect door s overall condition. The appropriate signage should be present and the hardware should be in good condition. 6. Have door inspected by an AAADM certified inspector at least annually. DO NOT USE DOOR if it fails any of these safety checks of if it malfunctions in any way. Call a qualified automatic door service company to have door repaired or serviced. See Owner s manual or instructions for details on each of these and other safety items. If you need a copy of the manual, contact the manufacturer. AAADM American Association of Automatic Door Manufacturers AAADM- ANNUAL COMPLIANCE INSPECTION INSPECT FOR AND COMPLIES WITH ANSI A56.9 ON: DATE: by AAADM Certified Inspector Number: ED5 DL6-6 -8

14 dormakaba ED5 Service Manual Chapter 9 9. ED5 environment and cleaning Table 9.. Ambient temperature 5 to F Suitable for dry rooms only Relative air humidity: 9% maximum, non-condensing Fig ED5 environmental requirements ED5 header assembly is designed to operate on an interior building surface under the specifications shown in Table 9... Operator enviromental requirements 9.. Areas around door(s) and door swing radius Areas around doors and door swing radius must be kept clear of all obstacles. ED5 header 9.. Cleaning WARNING Cleaning of header surfaces must be done with program switch in Close position! External surfaces of the header can be cleaned with a damp cloth and commercial cleaning agents. TIPS AND RECOMMENDATIONS Abrasive (scouring) agents should not be used as they may damage external surfaces. 9.. Water and other liquids WARNING No water or other liquids must be sprayed or spilled on ED5 header! 9. Yellow LED, service level Fig Service level indicator Header cover must be opened to view operator LEDs. Service level indicator Power switch Red LED 5 Yellow LED 6 Green LED 5 6 Yellow LED on operator power switch side is service level indicator. Operator system should be scheduled for service when yellow LED is first illuminated, or annually, whichever comes first. TIPS AND RECOMMENDATIONS Reference Chapter, parameters, for information on: Parameter CS, reset service interval display. Parameter CC, cycle counter. ED5 DL6-6 -8

15 dormakaba ED5 Service Manual Chapter 9 9. Pull arm maintenance Fig. 9.. Pull arm with track assembly Track Slide shoe Pivot pin Shoulder screw, 5 M8 SHCS* 6 Conical spring 7 Flat washer 8 O ring WARNING Set program switch to CLOSE before performing maintenance! 5 mm hex key *custom SHCS Fig. 9.. Program switch Pull arm Cover 9.. Pull arm and track maintenance. Track Check for wear or damage.. Slide shoe and pivot pin Check for wear or damage. 5 Fig. 9.. Track mounting screws Track Cover Mounting screws. 9.. Track mounting screws. Remove cover from track.. Check tightness of track mounting screws. 9.5 Pull arm torque requirements Fig M8 SHCS* 6 Conical spring 7 Flat washer 9.5. Check pinion bolt (5) torque.. Insure M8 SHCS, conical spring and washer are properly seated in pull arm. Pinion bolt torque *custom SHCS CAUTION Pull arm Check shoulder screw () torque.. Hold pivot pin with mm open end wrench and use torque wrench with 5 mm hex key to check for 6 ft lb [5 N m]. Adjust if necessary. Fig Shoulder screw torque Track Slide shoe Pivot pin Shoulder screw, 5 mm hex key Pull arm ED5 CAUTION DL6-6 Using torque wrench with 5 mm hex key socket, torque M8 SHCS to 6 ft-lb. Using torque wrench with 5 mm hex key socket, torque M8 SHCS to 6 ft-lb. -8 5

16 dormakaba ED5 Service Manual Chapter Push arm maintenance Adjustment screw Push arm Connecting rod assembly. Nut M8 SHCS* *custom SHCS 5 Shoe 5. Shoe mounting screws () 6 Arm socket 7 Adjustment screw ball head Fig Push arm assembly Fig Arm socket and ball head Note: Exploded view shown for reference. WARNING Set program switch to CLOSE before performing maintenance! Fig Program switch 9.6. Push arm maintenance.. Push arm socket and adjustment screw ball head: Check for wear or damage.. Shoe and connecting rod assembly: Check for wear or damage.. Connecting rod nut: Check for tightness of nut against adjustment screw. 9.7 Push arm torque requirements 9.6. Shoe mounting screws to door.. Check for tightness of mounting screws. 8 M8 SHCS (custom) Fig Push arm M8 SHCS 9.7. M8 SHCS torque CAUTION Using torque wrench with 5 mm hex key socket, torque M8 SHCS to 6 ft-lb. 8 6 ED5 DL6-6 -8

17 dormakaba ED5 Service Manual Chapter Measure reveal depth, parameter rd. Reveal depth parameter rd Fig... Positive reveal Parameter Description Reference paragraph rd Reveal depth.. Reveal depth parameter. Reveal depth is set in increments of mm (approximately /8").. Measured reveal depth of mm (approximately /6") equals rd parameter value of.. Measure and record reveal depth, rd value ED5 header Push arm Positive reveal.. Reveal depth parameter Fig... Negative reveal Parameter rd value Reveal measurement TIPS AND RECOMMENDATIONS Use of CPD pull arm and lever (Para..): Value of parameter rd must be reduced by /6" []. Example: ED5 with CPD pull arm and lever in pull installation with reveal of mm ( /8"). Parameter rd setting = (Reveal of mm - mm).. rd parameter values.. ED5 reveal depths, rd parameter ED5 header Pull arm Track Negative reveal - /6 - - Reveal measurement Reveal measurement Reveal measurement -/ - - ED5 ED5 ED5 -/8 - - Inches [mm] rd Inches [mm] rd Inches [mm] rd / / /6 5 5 /8 5/ / 6 6 / 5/6 7 / 9 9 5/8 7 7 /8 / 7 7/ /6 5 /8 8 / 7/ / / 8 5/8 / / / / /6 /8 8 8 ED5 DL

18 dormakaba ED5 Service Manual Chapter Operator spring tension. Set operator spring tension Fig... Spring tension adjustment ED5 operator Spring tension adjustment access hole in header T handle hex key, 5 mm Fig... Spring tension Spring tension adjustment.. Operator spring tension function. Spring tension sets closing force on door.. Required spring tension is based on door width... Spring tension adjustment factory setting. Spring tension adjustment is factory set fully CCW, no spring tension.. Spring has to be pretensioned per Para CAUTION A minimum of ten spring tension revolutions are required to operate system. Spring tension setting revolutions Door width Inches 6 8 mm CAUTION Any change to spring tension setting requires a new learning cycle (Chapter )! Spring setting revolutions ED5 6 8 TIPS AND RECOMMENDATIONS System checks spring tension during learning cycle (Chapter ). Learning cycle will be canceled if spring is insufficiently tensioned; door will stop and display will show a rotating "" and an "F". 8 ED5 DL6-6.. Check door closing force. Para... table lists approximate spring tension settings.. Use pressure gauge to check door closing force at and adjust if necessary. Fig... Door pressure gauge 5 Door pressure gauge -8

19 dormakaba ED5 Service Manual Chapter Power fail closing speed. Set power fail closing speed Fig... Power fail closing speed potentiometer Power fail closing speed potentiometer Control board TIPS AND RECOMMENDATIONS Power fail closing speed potentiometer: Single turn Factory setting fully CCW. CCW increases closing speed. CW decreases closing speed. Terminal flat blade screwdriver required: /" [ - mm]. Power on switch Terminal board o ED5 DL Setting door closing speed upon power failure. Turn ED5 power switch OFF. Manually open door to 9 angle and let it close. If door closes in less than seconds, turn potentiometer / turn CW and retry test. Adjust as necessary to obtain closing time greater than seconds. NOTICE Fig... Power on switch.. It is imperative that door closing speed be set. If door closes in less than seconds, error message E 7 (System error, braking circuit) will be displayed. See Troubleshooting, Chapter

20 dormakaba ED5 Service Manual Chapter Perform learning cycle. Perform learning cycle CAUTION Learning cycle must be performed while motor is cold! CAUTION Step Press Press and hold down button until display changes. Door performs several movements and display shows a sequence of symbols. Movements of door must not be interrupted! Door must not be manually moved or held in position during the learning cycle! Display indicates door is at 7 position and is waiting for door opening angle to be set. CAUTION Step Manually move door to desired opening angle. Verify that the following parameters have been set (Para..9): AS, Installation type rd, Reveal depth Tb, Door width TIPS AND RECOMMENDATIONS Step 5 Press Maximum door angle is. Momentarily press down button to continue learning cycle. Door performs several movements and display shows a sequence of symbols. Movements of door must not be interrupted! During learning cycle: Operator functions are deactivated. Operator spring tension too low. Display with small rotating "o" and an "F" during learn cycle indicates spring tension is too low. Door will close. Step Step WARNING No personnel or objects must be in range of door motion during learn cycle! Secure motion range of door. Set program switch to CLOSE position. Step 6 Press. Increase spring tension (Chapter ).. Restart learning cycle (Step ). Door completes learning cycle. Display with two horizontal bars indicate operator is ready for operation. Momentarily press down button to cycle door. Rotating "o" and a "" indicates operator learning cycle is required. Step 7 Following automatic learning cycle, actual forces on door, and door opening and closing times must be measured and changed if necessary to insure compliance with ANSI/BHMA standards, reference Chapter 7. Step 9 Set program switch to Auto. ED5 DL6-6 -8

21 dormakaba ED5 Service Manual Chapter Parameters. Parameters.. Firmware version TIPS AND RECOMMENDATIONS..6 Changing parameter values.. Set program switch to the CLOSE position Program switch position Fig... Program switch Parameters descriptions incorporate firmware version v.... Firmware version Firmware version is displayed on digit display during initial commissioning... dormakaba handheld Firmware version can be displayed and updates accomplished using dormakaba handheld terminal. Reference Chapter 6 or dormakaba handheld manual. Fig... dormakaba handheld. Use button keypad as outlined in Steps through 8 to view or change parameter values. Fig... button keypad, digit display button keypad digit display < s Quit > s Reset > s PRG > s < s LEARN > 8s Fact-Setup Step Press and hold right button > s to enter program mode... Configuration parameters Configuration parameters (Para...7) are set during first commissioning...5 Driving parameters Driving parameters can be set once first commissioning has been completed. Reference Para.. for driving parameter detail. Step Step Step Step Press up or down button to scroll through parameters until desired parameter is displayed. Press right button to display current parameter value. Press right button again to enable editing of value, display will start flashing. Press up or down button to select desired parameter value. Step 5 Press right button to save selected value. Display stops flashing. Step 6 Press left button to return to selected parameter. Step 7 Press up or down button to scroll through parameters until next desired parameter is displayed. Step 8 Press left button for a minimum of s to exit program mode. ED5 DL6-6 -8

22 dormakaba ED5 Service Manual Chapter..7 Configuration parameters Parameter Description Driving parameter Description AS Installation type rd Reveal depth Tb Door width dl Door type..8 Driving parameters Driving parameter Description 5 So Opening speed, automatic mode 6 Sc Closing speed, automatic mode 7 dd Hold open time, automatic mode 8 dn Hold open time, night/bank 9 do Hold open time, manual opening of door Sb Wall masking on door swing (hinge) side ST Safety sensor test 8 be Input /a and X, G V locking device output configuration 9 CC Cycle counter, number displayed * EC Delete error log CS Reset service interval display (yellow LED) SL Factory setting level (Fact Setup button) OA Opening angle, set during learning cycle hd Door closer mode, automatic or manual 5 ha Power assist function activation angle 6 hf Power assist function force adjustment 7 hs Power assist function support for manual mode in door closed position 8 F Upgrade card, not used 9 F This paragraph left intentionally blank. SA SP Activation by safety sensor on approach (opposite hinge) side Suppression of safety sensor on swing hinge) side during initial movement F Professional upgrade card, not used F Professional upgrade card, not used Ud Locking mechanism delayed opening time 5 Pu Door preload prior to unlocking 6 TS PR (Power reserve) module test F5 Professional upgrade card, not used. F7 Upgrade card, not used F8 Upgrade card, not used 7 Fo 8 Fc Static force on door closing edge in opening direction (wind load control) Static force on door closing edge in closing direction (wind load control) 5 C Configuration of COM interface 6 bc Back check angle when door opened manually 9 EP EA Not used PG Push and Go Motor driven latching action, automatic mode Door opening angle at which motor driven latching action is activated PS Program switch type S 5 S DCW EPS, electronic program switch behavior following a power reset Internal program switch; switch function on delay 7 Td Door thickness (mm) 8 d Deactivation of drive, emergency pushbutton at X, and a, trigger type 9 d Night/bank function, trigger type 5 FC 5 Ad 5 HS Hinge clearance Hold open system release by manually closing door, trigger type Active door with astragal: caster angle, angle door must reach before passive door starts to open 6 du Door unlocking during business hours 7 Sr Status relay function, terminal block X7 ED5 DL6-6 -8

23 dormakaba ED5 Service Manual Chapter..9 Configuration parameters, detail Fig... Pull arm with track Parameter and value range, factory setting = bold. Parameter description Installation type Pull arm, wall mounting on swing (hinge) side (Fig...). CPD pull arm and CPD lever, wall mounting on swing (hinge) side (Fig...5). Fig...5 Pull arm and CPD lever with track - Standard push arm, wall mounting on approach (non-hinge) side (Fig...6). Fig...6 Standard push arm Push arm with track, wall mounting on approach (non-hinge) side. [Application specific] Reveal depth ED5 - to 9 Reveal is set in increments of mm (/8"), "" = mm ( /8" If using CPD pull arm and CPD lever (Fig..5)approximately /6" [ mm] must be deducted from actual reveal. Door width Tb ED5 7 to Door width is set in increments of mm ("), "9" = 9 mm (5."). ED5 [7-9 mm] 8" - 8" Door type Single door Double door Overlapping door (with astragal) Active door operator. to Double door Overlapping door (with astragal) Passive door operator. Double door Edgeless door (no astragal) Active door operator. Double door Edgeless door (no astragal) Passive door operator. ED5 DL6-6 -8

24 dormakaba ED5 Service Manual Chapter. Driving parameters detail.. Driving parameters detail. Parameter Value range Units Factory setting Description Opening speed, automatic mode. Opening speed refers to automatic mode. Speed can be adjusted using this parameter.. Internal monitoring system checks if parameter setting is admissible If setting exceeds 5 ED5 8-6 /s 5 value, the setting is alternately displayed with the permissible value.. After parameter set, verify setting meets ANSI/BHMA standard A56.9 (low energy) See Chapter 7. Closing speed, automatic mode. Closing speed refers to automatic mode. Speed can be adjusted using this parameter. 6 ED5-6* (v.) /s 5. Internal monitoring system checks if parameter setting is admissible. If setting exceeds admissible value, the setting is alternately displayed with the permissible value.. After parameter set, verify setting meets ANSI/BHMA standard A56.9 (low energy) See Chapter 7. Hold open time, automatic mode 7 - s 5. Hold open time starts once all internal, external, safety and push and go inputs have been opened or dropped, and door is in an open position.. Hold open time values from 5 to s are set in increments of second.. In low energy mode, a minimum hold open time of 5 seconds is required.. Hold open time can be retriggered. Night-bank hold open time 8 - s Hold open time, manual opening 9 - s Wall masking on door hinge side Night-bank (key switch) hold open time is set using this parameter.. Night-bank Hold open time starts once contact on night-bank activator input is opened and door is in an open position.. Night-bank hold open time can be retriggered.. Default hold open time of second that follows every manual opening of door can be adjusted using parameter do.. Hold open time starts when door is released.. Wall masking required if door opens against an obstacle.. When door reaches set wall masking angle, system will ignore signal from safety sensor on door swing (hinge) side.. The wider the detection range of safety sensor used, the greater the area must be in which system has to ignore sensor's emitted signal. To insure personnel safety, it is advised to keep this range as small as possible.. If set wall masking angle is exceeded when door is being opened, a rapidly flashing dot appears in top left hand corner of digit display. 5. Rapidly flashing dot disappears when door angle drops below set wall masking angle. ED5 DL6-6 -8

25 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Factory setting Description Safety sensor test Safety sensor parameter ST must be set to sensors used and if they are active-high or active-low. See E safety sensor test error, Para. 5.. Sensor test off. Sensor test on swing (hinge) side. Active-high Sensor test on swing and approach sides. Active-high - 8 Sensor test on swing and approach sides. Active-high Sensor test on swing side. Active-low 5 Sensor test on approach side. Active-low ST 6 Sensor test on swing and approach sides. Active-low 7 Wall mounted sensor with data line. Lock monitoring not available. 8 Sensor test overhead sensor type Bodyguard III or Premier T with monitoring input. Activation by safety sensor on approach (opposite hinge) side - Safety sensor's input is disregarded as soon as door is closed. Safety sensor can trigger an opening pulse while door is closed. Suppression of safety sensor on swing (hinge) side during initialization drive - Safety sensor on swing side is active during an initialization drive after a power on reset.. With SP set to, operator will disregard swing side safety sensor during initialization drive. After a power on reset, operator starts an initialization drive at slow speed. The initialization drive cannot be completed if safety sensor on hinge side is, or has been triggered. Delayed opening time for locking mechanism - * ms *. Delayed opening time delay starts as soon as door opening pulse has been generated.. Door opens on expiration of time delay.. If parameter is set to "" and input for locking feedback contact is closed, door will not perform a preload Pu before door unlocks.. Since various motor locks do not have feedback contacts, a delay of up to seconds is possible Door preload prior to unlocking 5-9. Door preload prior to unlocking; force with which door is pushed in the "closed" direction before door is opened.. The door may need to be pushed in closing direction (preload) in order to release electric strike to insure door opens.. Preload time is set by parameter Ud, delayed opening time for locking mechanism.. To maintain long service life, set preload force only as high as necessary. ED5 DL

26 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Power reserve module SVP-PR test Factory setting Description Test off 6 - TS 5. SVP-PR power reserve module test is performed once every hours, or minutes after AC power has been turned on. In event of an error: Unlocking is not performed and no automatic door movements are initiated. Error code E 5 is displayed, See Chapter 5, Para. 5., troubleshooting error codes. 6. SVP-PR power reserve module can be used but must be tested on a regular basis if using: SVP- DCW emergency escape motor lock with automatic latching action. M-SVP DCW emergency escape lock. 7. Test is automatically activated if a fire protection module is recognized in conjunction with SVP- DCW or M-SVP DCW locks. Static force in opening direction 7-5 *.5-. * N lbf 6 *.5 *. Static force in opening direction (basic parameter for wind load control). Static force on door closing edge can be changed using this parameter.. Internal monitoring system checks if parameter setting is admissible. If setting exceeds admissible value, the setting is alternately displayed with the permissible value.. After parameter set, verify setting meets ANSI/BHMA standard A56.9 (low energy). See Chapter 7.. ED5 low energy operator: static force range is reduced. Static force in closing direction 8-5 *.5-. * N lbf 6 *.5 *. Static force in closing direction (basic parameter for wind load control). Static force on door closing edge can be changed using this parameter.. Internal monitoring system checks if parameter setting is admissible. If setting exceeds admissible value, the setting is alternately displayed with the permissible value.. After parameter set, verify setting meets ANSI/BHMA standard A56.9 (low energy). See Chapter 7.. ED5 low energy operator: static force range is reduced. Motor driven latching action, automatic mode 9-9. System offers a motor driven latching action in automatic mode in addition to mechanical latching action.. The EP parameter setting is designed to increase static force on door to insure proper closing despite resistance caused by door seals or locking devices.. Setting should be increased step by step from a low setting so as to avoid damage to the system. Use the lowest possible setting.. Ensure that both the door itself and the arm or track installation are suitable for the additional, permanent forces. Motor driven latching action angle (v.7) - Door opening angle at which motor driven latching action EP is activated. Starting angle of the latching angle adjustable from. Keep closed force Off - 9 to 9. Keep closed force is: Permanently applied following motor drive latching action. Designed to keep door in closed position even if wind acts on door.. Keep closed force can be set from (off) to 9, maximum force. 6 ED5 DL6-6 -8

27 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Factory setting Description Push & Go Off -. Parameter is activated.. Automatic opening of door is started when door is manually moved out of the closed position.. Door close mode parameter hd must be set to "" (manual) to enable this function. Program switch type Internal, operator mounted program switches are active. External mechanical program switch with contacts is connected to operator terminal board. Internal program switch connector must be removed. - External DCW electronic program switch (EPS) is connected to operator terminal board. Internal program switch connector must be removed. Program switch control by TMS Soft control software.. DCW electronic program switch (EPS) is installed, and operator is also connected by the building management system to TMS Soft control software.. When PS is set to, the program switch functions can be changed from DCW (EPS) to TMS Soft.. DCW Electronic program switch (EPS) behavior following power reset -. In event of power failure, or if operator is deliberately switched off, EPS will automatically switch to last known position when power returns.. Important: The time at which power returns might not be during business hours and may affect insurance-compliant door locking requirements.. In event of power failure, or if operator is deliberately switched off, EPS will automatically switched to OFF position when power returns.. This function should be used iif insurance compliant locking if required. Internal program switches, switch on delay 5 - Operator will perform function of new switch setting as soon as internal program switch is moved.. Operator will perform function of new switch setting after a delay of seconds from when internal program switch is moved.. This function is useful if user has to pass through door and its connected detectors and sensors after program switch is set to new function. Unlocking during business hours Door is always locked when it reaches closed position In automatic mode, door will not lock when it reaches closed position. This achieves faster door opening when system is equipped with motor driven locks.. If an electric strike opener is used, it must be suitable for % continuous duty factor to avoid possibility of damage. ED5 DL

28 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Factory setting Description Status relay function, X7 terminals Status relay is deactivated. Status relay activated as soon as door reaches door "closed" position. Status relay activated as soon as door reaches door "open" position. Status relay activated when error codes are displayed on digit operator display. "Door closed and locked" activates status relay Status relay activated when information or error codes are displayed on digit operator display. 6. Status relay activated when door is opened further than opening angle parameter OA, set during learning cycle.. Parameter OA value can only be changed using dormakaba handheld or by performing another learning cycle. Locking device output configuration; output X, G (V) and input X6, /a Reference Chapter 7 Locking device output terminal X, G (V) is independent of Input X6, /a Locking device output terminal X, G (V) is turned on as soon as contact at X6, /a is opened... Terminal X, G V output is on for as long as contact at X6, /a is open, motor lock with a % duty factor is required.. This function is not available for DCW motor locks. Cycle counter 9-99 * cycles. Total number of opening and closing cycles displayed is shown in increments of. Display value, "",, cycles. Display value, "5", 5, cycles.. Total number of cycles can be displayed on dormakaba handheld.. A display value of "99" means 99, cycles or greater. Delete error log No function. -. When "" entered, Error log is deleted.. Parameter is then automatically reset to "". Reset service interval display, operator yellow LED No function. -. When "" entered: Service cycle counter is reset to,. Service interval is reset to months. Yellow LED not illuminated.. Parameter is then automatically reset to "".. Values other than default values must be set using dormakaba USA, Inc. handheld: Maintenance interval Maintenance cycles 8 ED5 DL6-6 -8

29 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Factory setting Description Factory setting level - Parameter SL is used to determine what data will be reset during factory setting process. Standard factory settings Program switches OFF. Door closed. Press button keypad down button for > 8 s.. All parameters reset to factory settings.. Procedure completed when "8" on digit displays blinks twice.. Installed upgrade cards remain valid and do not require reinstallation.. Learning cycle required. Extended factory settings Program switches OFF. Door closed. Press button keypad down button for > 8 s.. All parameters reset to factory settings.. Procedure completed when "8" on digit displays blinks twice.. Installed upgrade cards deleted from operator memory.. Parameter SL automatically reset to. 5. Control unit and upgrade cards can be used independently (delivery status). 6. Learning cycle required.. Opening angle -. Door opening angle set during learning cycle is displayed.. Opening angle can only be changed during learning cycle.. Due to installation and parameter tolerances, display value may not match actual door position. Door closer mode ED5 DL

30 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Factory setting Description -. Automatic mode. This mode is applicable whenever door is mainly opened automatically and where motion detectors are installed.. Mode is optimized for high frequency use.. Full energy upgrade card provides for higher door opening and closing speeds.. In case door is blocked during a closing cycle, operator reverses automatically. 5. Driving phase is optimized to provide reliable closing cycles. 6. Keep closed force (wind load control) parameter FH and Push & Go function parameter PG are only available in automatic mode.. Manual mode. This mode is applicable whenever door is mainly used manually and only rarely automatically.. In case door is blocked during a closing cycle, door will stop at its current position.. Driving phase optimized for manual opening cycles.. Power assist function parameter hf is only available in manual mode. Power assist activation angle 5-5 Power assist function 6 -. Setting of door activation angle for Power assist function (hf).. Higher settings of ha result in better spring force compensation for easier manual opening.. Power assist function is more sensitive the smaller the activation angle.. Force setting for Power assist function.. Power assist function only available with hd parameter =, manual mode.. ""; power assist function OFF; power assist function enabled for available values greater than.. Power assist function enabled when power assist activation angle ha reached. 5. The greater the value of hf, the easier the door can be manually opened from power assist activation angle ha. 6. If power assist set too high, door can open automatically. 7. Power assist function is not available If operator is switched off A smoke detector or emergency button has been triggered. Power assist function support for manual mode in door closed position 7 - hs. Setting for power assist function support with door in closed position.. Power assist function only available with hd parameter =, manual mode.. The greater the value of hs, the easier the door can be manually opened from the closed position. Upgrade card parameter values Upgrade card not installed, function not available. - Upgrade card installed, function not activated. Upgrade card installed, function activated. Upgrade card has been removed, function no longer available. Upgrade card, fire protection 8,, Not used. ED5 DL6-6 -8

31 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Factory setting Description 9 Not used. Upgrade card professional, impulse relay,,, Not used. Upgrade card professional, extended hold-open time,, Not used. Upgrade card professional, nurse - bed function (double doors only),,, Not used. Upgrade card barrier free toilet,,, Not used. Upgrade card DCW,, Not used. COM configuration interface 5 - Backcheck when door opened manually (v.9) Interface programmed for communication with dormakaba handheld. Interface programmed for use with Dorma USA, Inc. TMS Soft control software.. Angle after which door is braked when manually opened.. Back check level is automatically optimized during manual door opening cycles. This function improves door braking behavior in end position so door does not move beyond set opening angle OA Entered value is subtracted from set opening angle OA.. Example Opening angle, 9 Parameter bc, Door back check starts at 78. Door thickness 7 Td - 99 mm 5-7/8" /8". Parameter is entered in mm.. Door thickness affects measured door opening angle.. Parameter Td enables a more accurate door width to be entered, if required. ED5 DL6-6 -8

32 dormakaba ED5 Service Manual Chapter.. Driving parameters detail. Parameter Value range Units Factory setting Description Deactivation of drive; X6, and a, trigger type 8 - NC contact, drive function is deactivated when NC contact is open. NO contact, drive function is deactivated when NO contact is closed. Night-bank contact X; and 5, trigger type 9 - Release of hold-open system. NO contact, night-bank function is triggered when NO contact is closed.. Typically used when using a key switch or an access control system.. NC contact, night-bank function is triggered when NC contact is opened.. Typically used when connected to building management system to trigger doors (signal normally present) Upgrade care Fire Protection installed, users may release hold-open by manually moving door in closed direction.. A manual release button is not required.. Hold-open release by manually moving door in closed direction is deactivated.. A manual release button is required. Castor angle for double doors 5 - Active door with astragal, angle active door must open before passive door opens. Hinge clearance 5 ± 5 * ±/6 * mm inches *. Clearance between hinges is critical for the calculated door angle.. It may only have a small effect but the clearance can be adjusted in extreme cases to improve accuracy.. Factory setting is *, mm, /6".. With CPD doors, setting must be changed to a negative value. A learning cycle is then required as system creates an angle table as a function of the set parameters. ED5 DL6-6 -8

33 dormakaba ED5 Service Manual Chapter 5 5 Troubleshooting 5. Information and error codes Fig. 5.. User interface button keypad digit display < s Quit > s Reset < s 5.. Overview Operator monitors internal circuits and external safety circuits managed by the operator. > s PRG > s LEARN > 8s Fact-Setup Fig. 5.. Operator LEDs Power switch Red LED 5 Yellow LED 6 Green LED 5 6 Fig. 5.. Program switch 7 Program switch, Close position 7 CLOSE AUTO OPEN TIPS AND RECOMMENDATIONS Para. 5., Information codes Para. 5., Error codes 5.. Error and information messages. With operator in use, certain conditions may develop resulting in error or information messages.. Operator attempts to identify the cause and respond accordingly.. Response depends on the severity of the error: Information message (ln) Error message (E) Deactivating the operator's automatic function; operator will switch to emergency mode. Users can then access door manually. 5.. User information display. User interface display, or or dormakaba handheld displays: Information ln codes Error message E codes 5.. Viewing error messages. To access and view error messages, briefly press the right button on the button keypad Red LED on operator. Red LED adjacent to operator power switch displays blinking codes for: Certain ln information E error codes (Para. 5.) 5..6 Resetting error codes. Options for resetting error codes:. Set program switch in Close (off) position.. User interface Reset buttons: Press both left and right buttons >s to reset system (v.8). Header cover must be opened to access user interface.. Power reset: Turn power switch OFF. Turn power switch back on after seconds. CAUTION Always analyze and remove cause for error before resetting error message! Troubleshooting charts (Para. 5.,.) are intended as a guide for diagnosing errors. ED5 DL6-6 -8

34 dormakaba ED5 Service Manual Chapter Error message memory.. There are ten error message memory locations; E through E 9.. The latest error message is always stored in error memory location E : As soon as another error occurs, the existing error stored in E will be moved to E and the latest error will be stored in E.. A maximum of 9 errors can be stored in memory locations E through E9.. Identical error messages occurring one after another are not stored again. 5. Red LED status codes 5.. Red LED status codes Red LED status Display Description Steady flashing Control unit has detected error, emergency mode activated. On steady ln Hold-open device triggered. Flashing times E Locking device error. Flashing times E Safety sensor test error. Flashing 5 times E 5 SVP PR DCW module test negative. Flashing 5 times E 5 E 5 E 5 Incremental encoder error. Flashing 6 times E 6 Flashing 6 times E 6 Flashing 7 times E 7 Flashing 7 times E 7 Double door operation, nd system has incompatible firmware version. Double door operation, nd system has incompatible fire protection setting. System error (test), second shutdown option. System error (test), current measuring circuit. Flashing 7 times E 7 System error (test), braking circuit Flashing times E EEPROM error Flashing times E Motor overcurrent Flashing 5 times E 5 Faulty learning cycle ED5 DL6-6 -8

35 dormakaba ED5 Service Manual Chapter 5 5. Troubleshooting chart, "ln" codes 5.. Troubleshooting chart, information messages. No. Display Red LED Description Troubleshooting information messages Sustained operation on a door with an obstruction can result in damage to drive.. Object or person obstructing door movement. Check door movement while system is deenergized. ln Off Obstruction Door obstructed by an obstacle or person; door movement stopped by operator. Remove cause of anything obstructing door movement.. Sensor detection range too small. Obstructions are often caused by people using door due to sensor's detection range not matching operator's opening speed. Door is unavoidably contacted by person using door. Sensors detection range should be increased and/or operator's opening speed should be increased.. Test system operation after cause of obstruction found. ln 8 Off Deactivation of drive function Contact at X6, and a is opened. Operator switched to emergency mode, door can only be used manually. An emergency close switch, lock switch, or other system safety device may be connected to the X6 input.. One of the activators connected to X6 may have opened, or a defect is present.. Reset the applicable activator. Operator should start operation automatically.. If ln 8 still present, check activators or system wiring. ln 9 Off Upgrade card error Installed upgrade card has been removed. If two upgrade cards were installed, the upgrade card installed first (container module) has not been reinstalled or is defective.. Not used. ln On Hold-open system triggered.. Hold-open system can be triggered: Automatically by smoke detector or building interface system. Manually by a manual release button. Manually moving door.. The system must be reactivated by a deliberate action.. Depending on system's configuration, reactivation can be done by: Manually moving door to taught opening angle. Switching program switch to Close (off). Pressing both button keypad left and right buttons >s.. It must be ensured that a smoke detector or building interface has not been triggered. 5. If reactivation is unsuccessful, there may be a defect in the smoke detector or building interface system or its connections. 5 ln Off Locking alarm Door is blocked while in the closed position.. Most common cause of this error is the drive unit attempting to open a locked door.. To eliminate the occurrence of this error, install a lock status switch. Lock switch detects the lock pin's switching status and switches the drive unit off if necessary.. It is recommended to use a lock status switch, as repeated attempts to open a locked door may damage the drive unit or the door. ED5 DL

36 dormakaba ED5 Service Manual Chapter Troubleshooting chart, information messages. No. Display Red LED 6 ln 6 Off Description Communication error, double door system No communication between the two operators. Troubleshooting information messages. Check communication cable connection at the two operators. Cable connects to the horizontal RJ 5 connector next to the user interface. Reference ED5 Installation manual, Para..7.. Check communication cable. 7 ln 7 Off Current measuring circuit System could not successfully perform internal current measuring test, performed once every hours.. The initial current measuring test my not always be successfully completed due to system tolerances and environmental conditions.. The test may also fail, as an example, if someone uses the door while the test is in progress. 8 ln 7 Off Braking circuit test System could not successfully perform internal braking circuit test, performed once every hours.. The initial braking circuit test my not always be successfully completed due to system tolerances and environmental conditions.. The test also may fail, as an example, if someone uses the door manually while the test is in progress.. If the cyclical test fails ten times in a row, error message ln 7 will be displayed. 9 ln 9 Off DCW communication At least one registered DCW device is missing.. Reconnect the corresponding DCW device.. If this is not possible, reactivate the drive. Reactivation can be done by: Switching program switch to Close (off). Pressing both button keypad left and right buttons >s. 5. Troubleshooting chart, "E" codes 5.. Troubleshooting chart, "E" codes. No. Display Red LED Description Troubleshooting error codes Locking device error Operator is attempting to open E Flashing x or close a locking device with feedback, or a DCW locking device. An error has occurred during this process.. Probable causes are a defective locking device or wiring defect. Check the locking device and feedback system. E Flashing x DCW program switch is missing.. Check the DCW program switch and its connections.. Factory setting level of "safety sensor test" parameter ST is, test off (Chapter, Parameters). E Flashing x Safety sensor test error Test of moving safety sensors was unsuccessful.. When ST is configured to installed safety sensors, a test signal is sent to the sensors before each door opening or closing cycle. Operator waits for a response within a certain time window.. Check whether parameter ST has been configured to the installed safety sensors and their active-high or active-low signal level.. Check for activation of the test at the safety sensors. E Flashing x EEPROM error Internal memory check could not be completed. Drive unit works in door closer mode.. Using dormakaba handheld, reload current firmware to reinitialize system.. If the error is still present, the control unit must be replaced. 6 ED5 DL6-6 -8

37 dormakaba ED5 Service Manual Chapter Troubleshooting chart, "E" codes. No. Display Red LED Description Troubleshooting error codes 5 E Flashing x Overcurrent detection Motor is consuming more current than drive unit can provide.. Motor is consuming too much power, check for any external causes.. Drive unit or control unit is defective.. If error repeats, operator must be replaced. 6 E 5 Flashing 5 x Faulty learning cycle. Learning cycle could not be completed (Chapter ).. Error may occur if learning cycle has been interrupted, for example if door movement has been interrupted during the learning cycle.. Learning cycle must be repeated. 7 E 5 Flashing 5 x SVP-PR power reserve module test negative. See Chapter, parameter TS, Power reserve module test.. Check power reserve module and its wiring.. Check encoder plug connection at operator: Ref. Chapter. 8 E 5 E 5 E 5 Flashing 5 x Incremental encoder error Motor gear unit encoder monitoring detected a faulty state. Secure connection. Wiring terminations Short circuits.. Check locking device for short circuits.. Error can be caused by defective motor or short circuit in locking device.. Motor gear unit must be replaced in event of defective motor. 9 E 6 Flashing 6 x Incompatible firmware version, double door system, second system.. Equip both operators with same firmware version. E 6 Flashing 6 x Incompatible fire protection setting, double door system.. For double door systems, the Upgrade card fire protection must be installed in both control units.. In order to reliably switch off the drive unit, several switching E 7 Flashing 7 x System error, nd shutdown option elements are used and their functions are tested periodically.. If the function test always results in the error code, the control unit must be replaced.. The current measurement circuit is part of the safety E 7 Flashing 7 x System error, current measurement circuit mechanisms and its function is tested periodically.. If the function test always results in the error code, the control unit must be replaced.. The braking circuit is a safety element in the closer mode and will be tested every hours. During the test the motor is shut down during door closing and E 7 Flashing 7 x System error, current measurement circuit the door closes at a set angle in emergency mode. Test can be noticed as a short jerk on the door and is normal.. Error can be due to door closing in the deenergized state too fast (under seconds). See Chapter.. Check the closing speed and reduce if necessary.. Movement dynamics in the closed direction will be reduced. Energy management Motor is too hot (for example, too high an ambient temperature) System responds automatically. Movement dynamics in both the open and closed directions will be reduced. System shuts down for minutes (door closer mode). Hold-open time will be extended. ED5 DL

38 dormakaba ED5 Service Manual Chapter 6 6 dormakaba handheld 6. dormakaba handheld terminal Fig. 6.. dormakaba handheld Off/On key Function keys Arrow keys ENTER key 5 DEL key 6 SHIFT key 7 Alpha numeric keyboard 8 6 LED, recharging F F F abc def jkl 5 mno pqrs tuv wxyz OFF ON.,# ghi (Off when batteries fully charged) 8 SD card slot ENTER SHIFT battery status */ 5 DEL 6.. Interface cable Use dormakaba interface cable (Article No ) to connect dormakaba handheld to operator Com interface. CAUTION Never use conventional network cable with RJ5 plug! Using conventional cable may result in permanent damage to operator! Fig. 6.. Com interface digit display button keypad Com interface 6.. Handheld key functions.. OFF ON, switches Handheld on or off.. Function keys F - F, trigger functions shown in bottom line of display (e.g., "RPT" for repeat, "UP" and "DOWN" to switch lines, "UpDoLd" for file up and download, "CHANGE" to change values, "OPEN" to trigger opening pulses.. Arrow keys, allow navigation within the display. Use left arrow to get back to previous screen.. ENTER, selects individual menu items and confirms changes of values and settings. 5. DEL, deletes figures or letters. 6. SHIFT, switch between figures and letters or small and capital letters. Current function is indicated on display (n: numeral, A: capital letters, a: small letters). 7. Alpha numeric keyboard, allows entering values and fie names in small and capital letters. There are several special characters (dot, comma, hash key, plus, minus, asterisk and diagonal slash). 6.. Handheld startup.. Press OFF ON to turn on Handheld terminal.. Screen displays Current version, creation date and name of data base. Handheld is ready for operation.. Select "COMMUNICATION" and enter user code (dormakaba original setting: 56).. Handheld displays current software version of the connected operator (e.g., ED5 SW- V.9). 6.. Downloading current parameters.. Press function key F "UpDoLd" to access menu "UP/DOWNLOAD".. Select "Download" to download current adjustments and parameters. System stores this data as temporary file under file name "temp.tab".. Every change in configuration, parameter setting or special functions confirmed with the "ENTER" key automatically uploads to the operator.. The Handheld does not automatically save the changes. The Handheld will prompt you to save the changes when quitting the menu Menu structure MAIN MENU Communication Files Change user code Extras CONNECTING...! User code: ****** Address: MAIN MENU ED5 SW-V:.9 Again UpDoLd Door 8 ED5 DL6-6 UP/DOWNLOAD Download Upload file Firmware upload Change user code Door temp.tab Configuration Driving parameters Special functions Diagnosis Save file as File upload Door -8

39 dormakaba ED5 Service Manual Chapter 6 NOTICE Parameters and detail may change depending on firmware version. 6. dormakaba handheld; configuration parameters "#" refers to reference numbers in Parameter list, Chapter. 6.. Configuration parameters # Parameter and default Installation * Description / Selections Pull arm Push arm Gleit BGS (Track w push arm) cm Inches # Parameter and default Start safety push side * Description / Selections Off* On Signal ignored once door closed Sensor can trigger pulse with door closed Reveal depth ED5 (-)- Door width (steps of ") - /6... /6 ED single*. leaf Lock delay 5 Unlock force Test PR module * Delayed opening time for locking mechanism Preload prior to unlocking * Test off (... ) * msec... 9 * Test once every hrs. Door type *. leaf Master Program switch * Internal* External DCW Slave off PGS power up (DCW) * Last* Off Pull side high active Push side high active 5 PGS delay * Off* On Off* Sensor test Both sides high active Pull side low active 6 Daytime unlock * On Off Relay off Locking device remains permanently unlocked while door is in closed position. 5 Push side low active Open* door reaches closed position 6 Both sides low active 7 Bodyguard 8 Bodyguard III or Premier T with monitoring 7 Door status (Status relay function, X7 terminals) * Close door reaches open position Error any error message 5 door closed and locked Information or error codes displayed 6 Door opened further than opening angle ED5 DL

40 dormakaba ED5 Service Manual Chapter Configuration parameters # Parameter and default Description / Selections # Parameter and default Description / Selections Manual mode Power assist winkel (angle) Power assist kraft (force) Keep closed force Manual release On On On* Off Manual mode on. Manual mode disabled. Activation angle for power assist function (... 5) Force adjustment for power assist. Force activated after latching action Off; function deactivated. Manual release button required to deactivate hold open function. On; function activated. Moving door manually in closing direction from hold open position deactivates hold open function. 9 Input Night-bank 7 Door depth 5 5 Hinge clearance I Out I Out I Out Normal* Inverse NO contact; nightbank function triggered while contact closed. NC contact; Nightbank function triggered while contact open mm mm... 7/8" -/6... +/6" 8 Input enable operator * Normal* Inverse NC contact, operator deactivated when contact is open NO contact, operator deactivated when contact is closed I Out 6. dormakaba handheld; driving parameters 6.. Driving parameters # Parameter and default Description / Selections # Parameter and default Description / Selections 5 Speed open 5 ED Speed close 5 ED /s /s 7 max. L.E.mode 7 max. L.E.mode 5 Offenhaltez man. Wall blanking 8 Hold-open time manual mode Angle when system ignores safety sensor on hinge side (... s ( ) 7 Limit force open 6 Static force in opening direction (wind load control) (...67) N L.E. mode 9 Latching action Motor-driven latching action, automatic mode (... 9) 8 Limit force close 6 Static force in closing direction (wind load control) (...67) N L.E. mode Latching angle Opening angle, motor-driven latching angle activated. (... ) 7 Hold-open time 5 Hold-open time automatic mode (... ) s 6 Backcheck angle Backcheck angle for manual opening cycles. (5... ) 8 Nurse bed function Hold-open time nurse bed function (... ) s 5 Coord. offset angle Starting angle for second door of two door system. (... ) ED5 DL6-6 -8

41 dormakaba ED5 Service Manual Chapter 6 6. dormakaba handheld; special functions (Upgrade cards) ED5, Not used 6.. Special functions (upgrade cards) # Parameter and default Description / Selection # Parameter and default Description / Selection Upgrade card status codes locked: not available unlocked: available, not active activ or active: activated fehlt: upgrade card missing 9 Full energy locked unlocked active Upgrade card full energy Not used locked fehlt Flip-flop func. unlocked active fehlt Upgrade card professional Not used DCW locked unlocked active Upgrade card DCW Not used extend HOT (extended hold-open time) locked unlocked active fehlt Upgrade card professional Not used Disabled restr fehlt Upgrade card Barrier-free toilet Not used locked 8 Nurse-Bed func. Fire protection unlocked active fehlt locked unlocked active Upgrade card professional Not used Upgrade card fire protection Not used Push & Go * Off* On Door opens automatically when moved manually by from closed position. Only available when "manual operation" is turned "off". fehlt ED5 DL6-6 -8

42 dormakaba ED5 Service Manual Chapter dormakaba handheld; diagnostics 6.5. Diagnostics Parameter name Description Setting Parameter name Description Setting FW vers BM Rev FW version FW version SK Displays firmware (FW) version of basic module Displays firmware version of Service Key x.x y y (e.g.,9 v.9.)... zzz x x.y y (e.g.,. = v..) Wartungs datum Cycles total Maintenance data Displays total opening and closing cycles x x y y (month, year) (.. ) FW bootloader x x y y Zyklen max h Displays maximum number of cycles in one hour (.. ) h Current error Displays current error (... ) Error log (... ) Zyklen / h Displays number of cycles in previous hour (.. ) h Error log (... ) Error log (... ) Error log (... ) Zyklen / h akt. Learning cycle Displays number of cycles in current hour Press "ENTER" to start learning cycle. (.. ) h Cmd-> Error log 5 (... ) Error log 6 (... ) Learn cycle stat. Indicates status of learning cycle (.. ) Error log 7 (... ) Error log 8 (... ) Factory reset Press "ENTER" to reset system to original settings Cmd -> Error log 9 (... ) Latching action p/u (...) kg Current information Delete errors Displays current error (... ) Press "ENTER" to delete error log. Cmd -> Setup level (Ref. parameter SL, no. 8) - Level, standard original settings. - Level, extended original settings - Level - Level Installation dat Displays date of installation (month / yr) mmyy (e.g., November ) DCW list Displays DCW list List -> Hours counter Displays number of operating hours (.. ) h DCW reset Cmd -> Service time interval Enter maintenance interval (6.. ) months Function mode Displays program switch setting (.. ) Service cycle interval Enter number of opening and closing cycles until next maintenance (.. )* ED5 DL6-6 -8

43 dormakaba ED5 Service Manual Chapter Diagnostics Parameter name Description Setting Parameter name Description Setting Setting code Inp. Night - bank Status of Night -bank input X9, 6 and, low active (function on), function off Klemme G Opening width Cur. door position Clamp X, G and, V out Displays opening angle (.. ) Displays current door angle (.. ) Inp. OPEN Inp. PART OPEN Inp. EXIT ONLY Status of program switch permanent OPEN input X, Status of program switch PARTIAL OPEN input X, Status of program switch EXIT ONLY input X, Amb. temp. Amb. max Motor temp. Motor temp max. Displays ambient temperature Displays maximum ambient temperature Displays motor temperature Displays maximum motor temperature (.. ) C (.. ) C (.. ) C (.. ) C Inp. AUTO Status of program switch AUTO input X, Com Com connection (.. ) Inp. OFF Status of program switch OFF input X, Inp. Sfty pull side Status of safety sensor, hinge side input X5, 5 Inp. Sfty push side Status of safety sensor, opposite hinge side X5, Inp. Activ extern Status of external activation sensor X6, Inp. Activ intern Status of internal activation sensor X6, Inp enable operator Status of Emergency close input X6, and a Inp. smoke detector Status of smoke detector input X9, and Inp. lock status Status of locking device input X, and Locking status locked ED5 DL6-6 -8

44 dormakaba ED5 Service Manual Chapter dormakaba handheld; firmware update 6.6. Firmware update procedure CAUTION For all firmware changes, set program switch to CLOSE and allow door to close completely before any updates are made! Fig Handheld power on sequence. Connect Handheld to COM port (Para. 6.) and power on. Handheld will boot up and display main menu. ENTER button Fig Select communication menu Fig Enter Handheld user code. With Communication highlighted, press ENTER.. Enter handheld user code and press ENTER. ED5 DL6-6 -8

45 dormakaba ED5 Service Manual Chapter 6 ENTER button F button Up/down arrows Fig Select UpDoLd Fig Select Firmware upload. Press F to select UpDoLd. Fig Select Firmware version 5. Use Up and Down arrows to select Firmware upload and press ENTER. Fig Start transmission 6. Use Up and Down arrows to select firmware version and press ENTER. Fig Firmware uploading 7. Press any key to start firmware transmission. Fig Complete firmware update 9. Press any key to complete firmware update. 8. Firmware uploading to controller. Wait time of to 5 minutes to upload. ED5 DL

ED900. Low energy operator. Customizing Features: Book 3 of 3

ED900. Low energy operator. Customizing Features: Book 3 of 3 Low energy operator Customizing Features: Book 3 of 3 2 TABLE OF CONTENT Contents Page 1. ettings / ervice 4-8 2. Diagnosis / Troubleshooting 9-10 3. Error messages 11-13 Customizing Features on Your Door

More information

Senior Swing Control Box. Table of Contents

Senior Swing Control Box. Table of Contents *740100* 740100 2800 Overhead Consealed Series 9500 Surface Applied Series Senior Swing Control Box Installation Instructions important These instructions are presented in step-by-step sequence. It is

More information

ED900. Low energy operator. Installation instructions: T/slide channel/pull arm mounting

ED900. Low energy operator. Installation instructions: T/slide channel/pull arm mounting Low energy operator Installation instructions: T/slide channel/pull arm mounting TABLE OF CONTENTS Operator overall Accessories External activation device minimum requirements Contact ratings Locking device

More information

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY 00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement

More information

Automatic Sliding Door Retrofit Drive Assembly. Installation Manual DoorControlsUSA.com

Automatic Sliding Door Retrofit Drive Assembly. Installation Manual DoorControlsUSA.com Automatic Sliding Door Retrofit Drive Assembly Installation Manual 800-437-3667 DoorControlsUSA.com TABLE OF CONTENTS pg. 1. COMPONENTS 2 2. HEADER PREPARATION 2 3. DOOR PREPARATION 2 4. MOTOR AND CONTROLLER

More information

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY 0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod

More information

TS93 EMF T/PT/TDE. Surface applied door closer

TS93 EMF T/PT/TDE. Surface applied door closer TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress

More information

LCN AUTOMATIC OPERATORS

LCN AUTOMATIC OPERATORS LCN AUTOMATIC OPERATORS SENIOR 9530 SENIOR 9540 SENIOR 9550 SENIOR 9560 8310 ACCESSORIES LCN ELECTROMECHANICAL POWERED SYSTEMS ELECTROMECHANICAL AUTOMATIC OPERATORS LCN s electromechanical products are

More information

KEANE MONROE a member of the record group

KEANE MONROE a member of the record group SERIES 3000 / 3100 MICROPROCESSOR CONTROL REGULAR ARM SLIDE ARM / SLIDE ARM W/PANIC BREAKAWAY SERIES 3000 / 3100 Page 1. INDEX and OPERATOR HANDING The KM Series 3000/3100 operators have been carefully

More information

INSTALLATION GUIDE For Surface Mounted Applications (Purchased after 08/01/2018)

INSTALLATION GUIDE For Surface Mounted Applications (Purchased after 08/01/2018) Low Energy Swing Door Automatic Operator INSTALLATION GUIDE For Surface Mounted Applications (Purchased after 08/01/2018) IMPORTANT READ THIS SECTION BEFORE PROCEEDING WITH INSTALLATION Security Door Controls

More information

5600 Series Power Operator Installation and Instruction Manual

5600 Series Power Operator Installation and Instruction Manual 5600 Series Power Operator Installation and Instruction Manual 80-956-000-00 (08-) 5 ASSA ABLOY 6 Item No. Description Motor (5600M) Cover (5600COV) Control Inverter (5600IN) Power Supply VDC (5600PS)

More information

What s on your truck? MOTIONACCESS, LLC. Installation & Operation Manual

What s on your truck? MOTIONACCESS, LLC. Installation & Operation Manual What s on your truck? Installation & Operation Manual Terminal Block Keypad Controller Cover & Label "Quick Harness" Sensors / Switches Connections A Digital Comm. B common C Thres. Sensor D common E Breakaway

More information

B-RAD Select USER MANUAL TABLE OF CONTENTS

B-RAD Select USER MANUAL TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS... 1 MANUAL REVISION HISTORY... 2 IMPORTANT SAFETY NOTICE... 3 1.0 General Information... 5 1.1 System Components... 5 1.2 Specifications... 5 1.2.1 Torque Ranges...

More information

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING CAUTION 80-957-00-00 (08-0) Series 570 Openings 85 to 0 or to 70 Double Lever Arm Application for Frame Reveals (76) to 7 (78mm)* Stop (Push) Side of Installation 5700 LEO Operator Installation Instructions

More information

Power Operators. Requirement. Approved Manufacturers. -All Operators To Be Electrically Powered -Operators To Be Aluminum (BHMA 689) Finish

Power Operators. Requirement. Approved Manufacturers. -All Operators To Be Electrically Powered -Operators To Be Aluminum (BHMA 689) Finish Power Operators Requirement -All Operators To Be Electrically Powered -Operators To Be Aluminum (BHMA 689) Finish Approved Manufacturers -Besam No Substitution 9 SW200i Technical Data Sheet ASSA ABLOY,

More information

Setup and Programming Manual

Setup and Programming Manual Microprocessor and Handy Terminal Setup and Programming Manual Versions U04 to U19 for Sliding Door Systems P/N 159000 Rev 7-2-07 The manufacturer, NABCO Entrances, Inc. suggests that this manual be given

More information

ESA II. I - Revive Slider Conversion Kit. Installation instructions

ESA II. I - Revive Slider Conversion Kit. Installation instructions ESA II I - Revive Slider Conversion Kit Installation instructions DL058-00 05-0 EN dormakaba ESA II I-Revive Slider Conversion Kit Table of Contents Table of contents Table of contents General information

More information

OPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets

OPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets Art. nr. 40200261 OPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets WHISPERPOWER BV Kelvinlaan 82 9207 JB Drachten Netherlands Tel.: +31-512-571550 Fax.: +31-512-571599

More information

5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY

5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY 5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY 80-957-000-00 (06-5) Patents 5,88,97; 7,6,096; 7,8, 6 5 0 8 7 9 Item No. Description Back plate Door Closer

More information

SE-3SCR-LM MANUAL MOTOR LOAD MANAGER

SE-3SCR-LM MANUAL MOTOR LOAD MANAGER 3714 Kinnear Place Saskatoon, SK Canada S7P 0A6 Ph: (306) 373-5505 Fx: (306) 374-2245 www.littelfuse.com/relayscontrols SE-3SCR-LM MANUAL MOTOR LOAD MANAGER MARCH 5, 2013 REVISION 4 MOTOR LOAD MANAGER

More information

SW10 (Full Power) & SW19 (Low Energy)

SW10 (Full Power) & SW19 (Low Energy) TUCKER AUTO-MATION SW10 (Full Power) & SW19 (Low Energy) INSTALLATION GUIDE Surface Mounted Applications (See APPENDIX for special notes regarding installation on fire rated doors) PLEASE NOTE: NEW 35mm

More information

Dor-O-Matic. Series Slide Control. Installation Instructions

Dor-O-Matic. Series Slide Control. Installation Instructions Dor-O-Matic Series 96000 Slide Control Installation Instructions DOR - O MATIC 7350 W. Wilson Ave. Harwood Heights, IL 60706 Toll Free: 1-800-543-4635 In Illinois: 708-867-7400 Sales FAX: 708-867-0291

More information

ESA-400 Fine Frame. Installation Instructions. 1 Rev. 8/06. Toll-Free: Lake Bluff, IL 60044

ESA-400 Fine Frame. Installation Instructions. 1 Rev. 8/06. Toll-Free: Lake Bluff, IL 60044 Interior View 0 Installation Instructions 1 Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring #2 Phillips (Crosspoint) - for various #8, #10, and #14 screws Wrenches

More information

5700 Series Power Operator Stop (Push) Side Mount Installation and Instruction

5700 Series Power Operator Stop (Push) Side Mount Installation and Instruction 5700 Series Power Operator Stop (Push) Side Mount ASSAManual ABLOY Installation and Instruction 80-957-0005-00 (06-5) Patents 5,88,97; 7,6,096; 7,8, 5 6 0 8 7 9 -/8 () Item No. Description Back plate Door

More information

HP21 SERVICE SUPPLEMENT UNIT INFORMATION. TSC6 Two-Speed Control

HP21 SERVICE SUPPLEMENT UNIT INFORMATION. TSC6 Two-Speed Control SERVICE UNIT INFORMATION SUPPLEMENT HP21 Corp. 9426 L10 Litho U.S.A. All HP21-4 and -5 units (single and three phase) are equipped with a TSC6 two-speed control. The TSC6 (A14) two-speed control contains

More information

2904 Power Supply Installation Instructions I-EA00041

2904 Power Supply Installation Instructions I-EA00041 FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and

More information

Model 2300JL Installation Guide

Model 2300JL Installation Guide Model 2300JL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300JL

More information

Intelli-Feed Controller User s Manual Intelli-Feed Digital Tachometer and Hourmeter

Intelli-Feed Controller User s Manual Intelli-Feed Digital Tachometer and Hourmeter Intelli-Feed Controller User s Manual Intelli-Feed Digital Tachometer and Hourmeter Part #: 9047 Table of Contents: Table of Contents 2 Intelli-Feed TM User Interface 3 Equipment Diagnostic Indicators

More information

Automatic Swing Door Operator DFA 127 IN (Inverse) Operating instructions E

Automatic Swing Door Operator DFA 127 IN (Inverse) Operating instructions E Automatic Swing Door Operator DFA 127 IN (Inverse) Operating instructions E Page 1. General 2 2. Safety instructions 3 3. Technical data and operating conditions 4 4. Construction and function 5-6 5. Operating

More information

Electro-Mechanical Swing Operator. Table of Contents

Electro-Mechanical Swing Operator. Table of Contents *640072* 640072 Electro-Mechanical Swing Operator Models 8230 & 8240 Installation Instructions Table of Contents General...1 Replacement Parts & System Components...1 1 Pre-Installation Site & Product

More information

DIGITAL BATTERY TORQUE WRENCH (BC-RAD SELECT) USER GUIDE

DIGITAL BATTERY TORQUE WRENCH (BC-RAD SELECT) USER GUIDE DIGITAL BATTERY TORQUE WRENCH (BC-RAD SELECT) USER GUIDE W.CHRISTIE (INDUSTRIAL) LTD CHRISTIE HOUSE, MEADOWBANK ROAD, ROTHERHAM, SOUTH YORKSHIRE, S61 2NF, UK T: +44(0)1709 550088 F: +44(0)1709 550030 E:

More information

Operator Manual. Transfer Switch. RSS100 and RSS Cummins Inc. All rights reserved. English

Operator Manual. Transfer Switch. RSS100 and RSS Cummins Inc. All rights reserved. English Operator Manual Transfer Switch RSS100 and RSS200 English 8-2007 962 0134 Table of Contents SECTION TITLE PAGE SAFETY PRECAUTIONS................................................... ii 1. INTRODUCTION.........................................................

More information

ROFU TJ 152-A. Y ALE SECURITY GROUP 50BC Series Door Closer. 50BC Series Door Closers. Sizing Chart for Installations. Ordering Information

ROFU TJ 152-A. Y ALE SECURITY GROUP 50BC Series Door Closer. 50BC Series Door Closers. Sizing Chart for Installations. Ordering Information ROFU 50BC Series Door Closers Specifications U.L. Listing All Yale 50 Series Door Closers with non-hold-open arms are listed by Underwriters Laboratories, Inc. for use on labeled fire doors. Tri-Pack Closer

More information

Hunter Automatics HA-8. Installation Manual

Hunter Automatics HA-8. Installation Manual Hunter Automatics HA-8 Installation Manual WARNING TO REDUCE RISK OF INJURY 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE

More information

SmarTire TPMS Maintenance Hand Tool. Revision User Manual

SmarTire TPMS Maintenance Hand Tool. Revision User Manual SmarTire TPMS Maintenance Hand Tool Revision 1.04 User Manual Page 2 Table of Contents FCC Compliance Label... 4 User Interface Illustration... 4 Introduction... 5 Testing Tire Sensors... 5 Main Menu...

More information

Roller Door Operator

Roller Door Operator INSTALLATION INSTRUCTIONS AND OWNERS MANUAL Roller Door Operator IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO COMMENCING THE INSTALLATION OF THE OPERATOR UNIT CAUTION This Automatic Opener

More information

Model 2300DL Installation Guide

Model 2300DL Installation Guide Model 2300DL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300DL

More information

OPERATING INSTRUCTIONS FOR SLIDING DOOR RETROFIT CONTROLLER DC-02

OPERATING INSTRUCTIONS FOR SLIDING DOOR RETROFIT CONTROLLER DC-02 OPERATING INSTRUCTIONS FOR SLIDING DOOR RETROFIT CONTROLLER DC-02 1. INTRODUCTION 2. SAFETY INSTRUCTIONS 3. SPECIFICATION 4. OPERATING INSTRUCTIONS AND CONTROL FUNCTIONS 5. SET UP PROCEDURE 6. CONNECTIONS

More information

Commander 15i Container and Pallet Loader. Property of American Airlines

Commander 15i Container and Pallet Loader. Property of American Airlines Commander 15i Container and Pallet Loader Section 2. Operation BEFORE ATTEMPTING TO OPERATE OR MAINTAIN THE VEHICLE, COMPLETELY READ AND UNDERSTAND THE OPERATION AND MAINTENANCE MANUAL, INCLUDING ALL DANGER,,

More information

SentryGOLD Compact. for Bennett Electronic Dispenser INSTALLATION MANUAL. Fuel Management System

SentryGOLD Compact. for Bennett Electronic Dispenser INSTALLATION MANUAL. Fuel Management System Fuel Management System SentryGOLD Compact for Bennett Electronic Dispenser INSTALLATION MANUAL 2901 Crescent Drive Tallahassee, FL 32301 (850) 878-4585 office (850) 656-8265 fax www.trakeng.com support@trakeng.com

More information

GLM SERIES CONTROL Users Manual Rev:

GLM SERIES CONTROL Users Manual Rev: GLM SERIES CONTROL Users Manual Rev: 808062 Connecting Power Page 2 Motor Terminal Wiring Diagrams Page 3 Getting Started / Setup Page 4 1. Obstruction Detection Devices Page 4 2. Checking Power and Direction

More information

ESA II CONTROLLER AND WIRING MANUAL

ESA II CONTROLLER AND WIRING MANUAL ESA II CONTROLLER AND WIRING MANUAL DORMA AUTOMATICS, Inc. Sherwood Drive Toll-Free: -- DL-00 Lake Bluff, IL 00 Fax: -- rev. A Contents Contents Tecnical data Comissioning Settings Function test Function

More information

*70954* 240V Senior Swing Control Box Installation Instructions CAUTION WARNINGS. Table of Contents

*70954* 240V Senior Swing Control Box Installation Instructions CAUTION WARNINGS. Table of Contents *70954* 70954 2800 Overhead Concealed eries 9500 urface Applied eries 240V enior wing Control Box Installation Instructions CAUTION These instructions are presented in step-by-step sequence. It is very

More information

User Manual Solar Charge Controller 3KW

User Manual Solar Charge Controller 3KW User Manual Solar Charge Controller 3KW Version: 1.3 CONTENTS 1 ABOUT THIS MANUAL... 1 1.1 Purpose... 1 1.2 Scope... 1 1.3 SAFETY INSTRUCTIONS... 1 2 INTRODUCTION... 2 2.1 Features... 2 2.2 Product Overview...

More information

IVTM Installation Manual

IVTM Installation Manual Integrated Vehicle Tire Pressure Monitoring IVTM Installation Manual 2nd edition Copyright WABCO 2006 Vehicle Control Systems An American Standard Company The right of amendment is reserved Version 002/06.06(us)

More information

Service Manual. Extractor Model XR28QP. For The. For: Troubleshooting Adjustments

Service Manual. Extractor Model XR28QP. For The. For: Troubleshooting Adjustments Service Manual For The X Ride 28 Rider Extractor Model XR28QP For: Training Troubleshooting Adjustments Contents 1 Cautions ------------------------------------------------------------------------------

More information

6100 Series Swing Door Operator Installation Instructions

6100 Series Swing Door Operator Installation Instructions 6100 Series Swing Door Operator Installation Instructions The manufacturer s specifications for this product require the installation to be approved by an AAADM certified inspector. -USA 4324 Phil Hargett

More information

SI AT A22. English. Printed: Doc-Nr: PUB / / 000 / 03

SI AT A22. English. Printed: Doc-Nr: PUB / / 000 / 03 SI AT A22 English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and

More information

DORMA Automatics, Inc. 924 Sherwood Drive Lake Bluff, Illinois U.S.A. Toll Free: Fax:

DORMA Automatics, Inc. 924 Sherwood Drive Lake Bluff, Illinois U.S.A. Toll Free: Fax: ARCHITECTURAL SPECIFICATION ED-700 SECTION 08460 Automatic Entrance Doors DORMA Automatics, Inc. Series ED-700 (Surface Applied) LOW ENERGY OPERATING SYSTEM FOR SWINGING DOORS 1.01 SUMMARY: A. Section

More information

BODYGUARD III-C USER S GUIDE

BODYGUARD III-C USER S GUIDE BODYGUARD III-C USER S GUIDE PRESENCE SENSOR DESCRIPTION The BEA Bodyguard III Presence Sensor (10BODYGUARDIII) is a self-monitored ready overhead-mounted diffused active infrared sensing device that provides

More information

CHAPTER 7 ERROR MESSAGE AND TROUBLESHOOTING

CHAPTER 7 ERROR MESSAGE AND TROUBLESHOOTING CHAPTER ERROR MESSAGE AND TROUBLESHOOTING VFD-V Series The AC drive has a comprehensive fault diagnostic system that includes various alarms and fault messages such as over-voltage, low-voltage and over-current.

More information

Compact Heat Meters. Features. -A Pulsed output. -B M-Bus output. Accessories. UK Sales Tel: International Tel:

Compact Heat Meters. Features. -A Pulsed output. -B M-Bus output. Accessories. UK Sales Tel: International Tel: Compact Heat Meters Features Compact design Simple operation Pulsed output Measures heating or cooling Specification Product Codes Water Meter Temp. range 10 to 90 C Nominal pressure 16bar Installation

More information

2001 Chevrolet Corvette ACCESSORIES & EQUIPMENT Remote Keyless Entry Systems - Corvette

2001 Chevrolet Corvette ACCESSORIES & EQUIPMENT Remote Keyless Entry Systems - Corvette DESCRIPTION 2001 ACCESSORIES & EQUIPMENT Remote Keyless Entry Systems - Corvette Remote Keyless Entry (RKE) system is controlled by Remote Function Actuation (RFA) system. Transmitter allows remote control

More information

Full-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG

Full-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG Full-featured operator with slim profile for moderate to high traffic applications 6300 S E R I E S LOW ENERGY OPERATOR CATALOG INTRODUCTION The Norton 6300 Series Low Energy Operator offers a broad set

More information

1.0 Features and Description

1.0 Features and Description 1.0 Features and Description The is an intelligent actuator designed for precise control of quarter turn valves and dampers. Using stepper motor technology, the SmartStep proportionally positions valves

More information

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires it.

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires it. Electric Wall Oven Technical Information AEW3630DD*, AEW4630DD*, JJW8230DD* MEW5627DD*, MEW5630DD*, MEW6627DD*, MEW6630DD*, Refer to Service Manual 6022506 for detailed installation, operating, testing,

More information

SmarTire TPMS Maintenance Hand Tool. Revision User Manual

SmarTire TPMS Maintenance Hand Tool. Revision User Manual SmarTire TPMS Maintenance Hand Tool Revision 1.03 User Manual Page 2 Table of Contents FCC Compliance Label...4 User Interface Illustration...4 Introduction...5 Testing Tire Sensors...5 Main Menu...6 Main

More information

Pressure chlorine changeover unit C 7520

Pressure chlorine changeover unit C 7520 BW 2 24 04 / 1 Content 1. Scope of delivery 2. Device description 3. Installation 4. Operation 5. Shutdown 6. Maintenance 7. Troubleshooting 1 Scope of delivery The chlorine gas changeover unit C 7520

More information

SENIOR SWING UNIQUE FEATURES

SENIOR SWING UNIQUE FEATURES SENIOR UNIQUE FEATURES Digital Control Suite Provides exceptionally precise control of a large range of built-in functions combined with superior durability and performance. Visual indications and digital

More information

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO

More information

TS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall)

TS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall) TS96 PKT 90/9 Surface applied door closer Installation instructions: Pocket door track mount in 90 /9 pocket (Closer on wall) TABLE OF CONTENTS Closer overall Technical specifications Door templates Closer

More information

SP PRO ABB Managed AC Coupling

SP PRO ABB Managed AC Coupling SP PRO ABB Managed AC Coupling Introduction The SP PRO ABB Managed AC Coupling provides a method of linking the ABB PVI-3.0/3.6/4.2- TL-OUTD and ABB PVI-5000/6000-TL-OUTD string inverters to the SP PRO

More information

ASSA ABLOY Series Multi-Point Hold Open Installation and Instruction Manual

ASSA ABLOY Series Multi-Point Hold Open Installation and Instruction Manual Pull Side Applications with Slide Track (7210, 7250) (see page 7 for template) 7200 Series Multi-Point Hold Open Installation and Instruction Manual 3 1 Push Side Applications with Double Lever Arms (7220,

More information

ST48-WHUV.102. Wiring diagram. Product description. PID controller. Order number

ST48-WHUV.102. Wiring diagram. Product description. PID controller. Order number ST48-WHUV.12 PID controller Order number 935.15 Wiring diagram Product description This micro-processed controller serves for temperature control at high measuring accuracy. Beside resistance sensors and

More information

PORTEO PORTEO. Weight Configurations Max door weight 100kg. Parameters Max door width 1100mm Max opening angle 110

PORTEO PORTEO. Weight Configurations Max door weight 100kg. Parameters Max door width 1100mm Max opening angle 110 PORTEO Automatic swing door operator The PORTEO offers an innovative and convenient way to open and close doors effortlessly, making it eminently suitable for barrierfree applications. Supplied in the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 0711016 Page 1 INSTALLATION INSTRUCTIONS ELECTRONIC DEADBOLT WITH KEYPAD latch 2-3/8 Your latch is now set 2-3/8 (60mm) backset latch 2-3/4 2-3/4" (70mm) 2-3/8" (60mm) Cylindrical cover Extension plate

More information

! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless testing requires power.

! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless testing requires power. Electric Freestanding Range Technical Information MER5875RA* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. Refer

More information

Cybex Arc Trainer Owner s & Service Manual. 7 - Service

Cybex Arc Trainer Owner s & Service Manual. 7 - Service 7 - Service Table of Contents......... iii Warnings/Cautions All warnings and cautions listed in this chapter are as follows:! WARNING: All maintenance activities shall be performed by qualified personnel.

More information

Muto Electro Magnetic Lock (Elock MEM4400) Installation instructions / Wiring manual

Muto Electro Magnetic Lock (Elock MEM4400) Installation instructions / Wiring manual Muto Electro Magnetic Lock (Elock MEM4400) Installation instructions / Wiring manual 936033 05-2018 EN Table of Contents Table of contents 1 Technical specifications 3 1.1 Overview 3 1.1.1 General information

More information

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery

More information

GARAGE DOOR OPERATOR USER S MANUAL

GARAGE DOOR OPERATOR USER S MANUAL GARAGE DOOR OPERATOR USER S MANUAL - DOMESTIC USE CIL-CD800S Chain) CIL-BD800S Belt GARAGE DOOR OPENER OWNER S MANUAL - DOMESTIC USE CIL-CD800S CD800S(Chain Chain) CIL-BD800S BD800S(Belt Belt) 1 Features

More information

Floating Headers - 4-1/8, 4-1/2, 6. with RTS88 and PT21 for double doors ONLY. Installation instructions

Floating Headers - 4-1/8, 4-1/2, 6. with RTS88 and PT21 for double doors ONLY. Installation instructions - 4-1/8, 4-1/2, 6 with RTS88 and PT21 for double doors ONLY Installation instructions 933842 EN Table of Contents Table of contents 1 Technical specifications 3 1.1 Overview 3 1.1.1 General information

More information

ADA EZ Rev. H, 8/23/11

ADA EZ Rev. H, 8/23/11 Installation and Operating Instructions ADA EZ Installation and Operating Instructions EZ040 Note Changes or modifications not expressly approved by the party responsible for compliance could void the

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

SI AT A22. English. Printed: Doc-Nr: PUB / / 000 / 01

SI AT A22. English. Printed: Doc-Nr: PUB / / 000 / 01 SI AT A22 English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and

More information

TECHNICAL CATALOG NEPTIS INVERS/INVERS-B ELECTRO-MECHANICAL OPERATOR FOR AUTOMATIC SWING DOORS, WITH SINGLE/DOUBLE LEAF

TECHNICAL CATALOG NEPTIS INVERS/INVERS-B ELECTRO-MECHANICAL OPERATOR FOR AUTOMATIC SWING DOORS, WITH SINGLE/DOUBLE LEAF NEPTIS INVERS/INVERS-B ELECTRO-MECHANICAL OPERATOR FOR AUTOMATIC SWING DOORS, WITH SINGLE/DOUBLE LEAF FOR SAFETY EXITS IN SMOKE EXHAUSTION SYSTEMS TECHNICAL CATALOG Automatic Door Solutions NEPTIS INVERS/INVERS-B

More information

QUICK INSTALLATION GUIDE

QUICK INSTALLATION GUIDE MANUAL/AUTOMATIC T R A N S M I S S I O N 2 - B U T T O N R E M O T E S T A R T E R W I T H V I R T U A L T A C H S Y S T E M ( A S P R G - 1 0 0 0 C O M P A T I B L E ) QUICK INSTALLATION GUIDE Manual

More information

56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions

56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions SECTION I: OVERVIEW 1. Description The Sargent 56- prefix ELR works with 80 Series exit devices to provide remote-controlled latch retraction. It is compatible with the following prefixes: 53 - Latchbolt

More information

USERS GUIDE LO-21U LOCKOUT RELAY

USERS GUIDE LO-21U LOCKOUT RELAY USERS GUIDE LO-21U LOCKOUT RELAY PRODUCT DESCRIPTION The LO-21U (PN: 10LO21U) is a micro-processed lock out module designed to operate on swing door applications with BEA s Bodyguard or DK-12 overhead

More information

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Dycon D1532SM EN50131/PD6662 Grade 3, 12V 2A Power Supply Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Tel: +44 (0)1443 471 900 Unit A Cwm Cynon Business Park Mountain

More information

KeContact P20. User manual

KeContact P20. User manual KeContact P20 User manual Comments to this manual In this manual you will find warnings against possible dangerous situations. The used symbols apply to the following meanings:!! WARNING! Indicates a potentially

More information

ELECTRIC ACTUATOR HVAC/BAC ELECTRIC IOM. E024, EO25, E026, EO29 & E030 Installation Operation and Maintenance Instructions TABLE OF CONTENTS

ELECTRIC ACTUATOR HVAC/BAC ELECTRIC IOM. E024, EO25, E026, EO29 & E030 Installation Operation and Maintenance Instructions TABLE OF CONTENTS HVAC/BAC ELECTRIC IOM ELECTRIC ACTUATOR E024, EO25, E026, EO29 & E030 Installation Operation and Maintenance Instructions TABLE OF CONTENTS Electric Actuator Specifications... 2 Overview... 3 Actuator

More information

Do isolate the power supply from other high power systems such as Stereos and Alarms

Do isolate the power supply from other high power systems such as Stereos and Alarms Thank you for purchasing a Smart Ride Air Management System, AIRBAGIT.COM s premier flagship product. This system will meet all of your custom and utility needs and will provide you years of trouble free

More information

Installation Instructions

Installation Instructions Smart Start Assist Kit For use with Single-Phase Residential Geothermal Heat Pumps 8-733-934-497 Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY

More information

SB 2000 PUSH TO SEARCH NEXT STAG E. Aerotech, Inc. FORM: QM 1320

SB 2000 PUSH TO SEARCH NEXT STAG E. Aerotech, Inc. FORM: QM 1320 Inlet Controller SB 2000 USER'S MANUAL AUTO OPEN MANUAL PUSH TO SEARCH NEXT STAG E CLOSE Aerotech, Inc. FORM: QM 1320 4215 Legion Dr. Mason, MI 48854-1036 USA Rev. 3, Sept. 1997 Ph. (517) 676-7070 Fax

More information

MDX-300 Series. For 12-volt automotive starting batteries and starting/charging systems INSTRUCTION MANUAL

MDX-300 Series. For 12-volt automotive starting batteries and starting/charging systems INSTRUCTION MANUAL For 12-volt automotive starting batteries and starting/charging systems INSTRUCTION MANUAL Blank page Contents Caution... 4 Capabilities... 4 Display and Keypad... 4 Preparations Before the Test... 6 Connecting

More information

Battery Management Innovation. For 12-volt automotive starting batteries and starting/charging systems INSTRUCTION MANUAL

Battery Management Innovation. For 12-volt automotive starting batteries and starting/charging systems INSTRUCTION MANUAL Battery Management Innovation For 12-volt automotive starting batteries and starting/charging systems INSTRUCTION MANUAL ! CAUTION Because of the possibility of personal injury, always use extreme caution

More information

Section 55 Chapter 6

Section 55 Chapter 6 Section 55 Chapter 6 REMOTE HYDRAULICS CONTROLLER Calibration and Fault Codes 6-12880NH TABLE OF CONTENTS REMOTE HYDRAULICS CONTROLLER CALIBRATION... 55-5 Requirements For Calibration... 55-5 Aux Set Main

More information

Product Guide: Series III Pump Control Board Set (RoHS)

Product Guide: Series III Pump Control Board Set (RoHS) revised 04/08/10 Description: The Series III Pump Control Board Set provides motor drive and pump control for a wide assortment of pumps from Scientific Systems, Inc. The assembly consists of two circuit

More information

TS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH)

TS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) Surface applied door closer Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) TABLE OF CONTENTS Technical specifications Size selection chart 2 Closer setup

More information

CONTENTS. GENERAL PRESENTATION 2 SAFETY INSTRUCTIONS 2 Caution 2 Safety instructions 2

CONTENTS. GENERAL PRESENTATION 2 SAFETY INSTRUCTIONS 2 Caution 2 Safety instructions 2 CONTTS GERAL PRESTATION 2 SAFETY INSTRUCTIONS 2 Caution 2 Safety instructions 2 PRODUCT DESCRIPTION 2 Product components 2 Area of application 2 POINTS TO CHECK PRIOR TO INSTALLATION 3 Preliminary checks

More information

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market 1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter

More information

Electrohydraulic Powered Systems

Electrohydraulic Powered Systems Electrohydraulic Powered Systems ELECTRIC AUTO EQUALIZERS These Auto Equalizer products are an addition to the original pneumatic drive system. People moving through a door can use it as a normal rack

More information

N1387 Series Troubleshooting Guide for N Alternators

N1387 Series Troubleshooting Guide for N Alternators N1387 Series Troubleshooting Guide for N1387-1 Alternators Hazard Definitions These terms are used to bring attention to presence of hazards of various risk levels or to important information concerning

More information

KEYLESS ENTRY SYSTEM & TIRE PRESSURE MONITOR ACCESSORIES & EQUIPMENT General Motors Corp. - Remote Keyless Entry System

KEYLESS ENTRY SYSTEM & TIRE PRESSURE MONITOR ACCESSORIES & EQUIPMENT General Motors Corp. - Remote Keyless Entry System KEYLESS ENTRY SYSTEM & TIRE PRESSURE MONITOR 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Remote Keyless Entry System DESCRIPTION Remote Keyless Entry (RKE) system is controlled by Remote Function

More information

B-PC20 Power Close Module

B-PC20 Power Close Module B-PC20 Power Close Module Instruction Manual Document number: B-PC20-C Release: V1.2 Date: OCT 12,2011 ! WARNING This control must be adjusted/serviced by a qualified person. The service technician must

More information

B100S - Super Swing. Instruction Manual. Document number: B100S-C Release: V4.0 Date: May 08,2009

B100S - Super Swing. Instruction Manual. Document number: B100S-C Release: V4.0 Date: May 08,2009 B00S - Super Swing Instruction Manual Document number: B00S-C Release: V4.0 Date: May 08,009 ! WARNING This control must be adjusted/serviced by a qualified person. The service technician must be familiar

More information

RD712 & RD712XL Remote Displays. Model 615 / 615XL Indicator User s Manual

RD712 & RD712XL Remote Displays. Model 615 / 615XL Indicator User s Manual RD712 & RD712XL Remote Displays Model 615 / 615XL Indicator User s Manual EUROPEAN COUNTRIES WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which

More information

SOLAR LIGHTING CONTROLLER SUNLIGHT MODELS INCLUDED IN THIS MANUAL SL-10 SL-10-24V SL-20 SL-20-24V

SOLAR LIGHTING CONTROLLER SUNLIGHT MODELS INCLUDED IN THIS MANUAL SL-10 SL-10-24V SL-20 SL-20-24V SOLAR LIGHTING CONTROLLER OPERATOR S MANUAL SUNLIGHT MODELS INCLUDED IN THIS MANUAL SL-10 SL-10-24V SL-20 SL-20-24V 10A / 12V 10A / 24V 20A / 12V 20A / 24V 1098 Washington Crossing Road Washington Crossing,

More information

Techcon Systems TS500R-PC Controller For Positive Displacement PC Pump

Techcon Systems TS500R-PC Controller For Positive Displacement PC Pump Techcon Systems TS500R-PC Controller For Positive Displacement PC Pump Copyright OK International CONTENTS Page Number 1. Safety 3 2. Symbol Definitions.. 3 3. Specifications... 4 4. Features.. 5 5. Setup

More information