DTC P0110 Intake Air Temperature Circuit Malfunction
|
|
|
- Esther Higgins
- 5 years ago
- Views:
Transcription
1 EINE (RZFE, 3RZFE) DI33 DII3 DTC P00 Intake Air Temperature Circuit Malfunction CIRCUIT DESCRIPTION Resistance kω Fig Acceptable ( 4) Temp. C (F ) The intake air temperature sensor is built into mass air flow meter and senses the intake air temperature. A thermistor built in the sensor changes the resistance value according to the intake air temperature. The lower the intake air temperature, the greater the thermistor resistance value, and the higher the intake air temperature, the lower the thermistor resistance value (See Fig. ). The intake air temperature sensor is connected to the (See below). The power source voltage in the is applied to the intake air temperature sensor from terminal via a resistor R. That is, resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the potential at terminal also changes. Based on this signal, the increases the fuel injection volume to improve driveability during cold engine operation. FI474 DTC No. DTC Detection Condition Trouble Area Open or short in intake air temp. sensor circuit P00 Open or short in intake air temp. sensor circuit Intake air temp. sensor (built into mass air flow meter) After confirming DTC P0, use the handheld tester or the OBD II scan tool to confirm the intake air temperature from the DIAGNOSIS/ENHANCED OBD II/DATA LIST/ALL. Temperature Displayed 40 C (40 F) Malfunction Open circuit 40 C (84 F) or more Short circuit 003 TOYOTA TACOMA (RM00U) 95
2 DI34 DIAGNOSTICS EINE (RZFE, 3RZFE) WIRI DIAGRAM Intake Air temperature (Built into Mass Air Flow Meter) YG R LB 8 E A0030 A0977 INSPECTION PROCEDURE If different DTCs that are related to different systems are output simultaneously while terminal E is used as a ground terminal, terminal E may be open. Read freeze frame data using the handheld tester or the OBD II scan tool, as freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the airfuel ratio was lean or rich, etc. at the time of the malfunction. Connect handheld tester or OBD II scan tool, and read value of intake air temperature. (a) Connect the handheld tester or OBD II scan tool to DLC3. (b) Turn the ignition switch ON and push the handheld tester or OBD II scan tool main switch ON. (c) Select the item DIAGNOSIS/ENHANCED OBD II/DATA Read the temperature value on the handheld tester or the OBD II scan tool. : Same value as the actual intake temperature. If there is open circuit, handheld tester or OBD II scan tool indicates 40 C (40 F). If there is short circuit, handheld tester or OBD II scan tool indicates 40 C (84 F) or more. 40 C (40 F)... Go to step. 40 C (84 F) or more... Go to step 4. Check for intermittent problems (See page DI3). 003 TOYOTA TACOMA (RM00U) 96
3 EINE (RZFE, 3RZFE) DI35 Check for open in harness or. 8 E E A750 (b) Connect the sensor wire harness terminals together. (c) Turn the ignition switch ON. (d) Select the item DIAGNOSIS/ENHANCED OBD II/DATA Read the temperature value on the handheld tester or the OBD II scan tool. : Temperature value: 40 C (84 F) or more Confirm good connection at sensor. If, replace mass air flow meter. 3 Check for open in harness or. E 8 E E (b) Remove the glove compartment (See page SF55). (c) Connect between terminals and E of the connector. The mass air flow meter connector is disconnected. Before checking, do a visual and contact pressure check for the connector (See page IN8). (d) Turn the ignition switch ON. (e) Select the item DIAGNOSIS/ENHANCED OBD II/DATA Read the temperature value on the handheld tester or the OBD II scan tool. : Temperature value: 40 C (84 F) or more A75 A8845 A8853 Open in harness between terminal E or, repair or replace harness. 003 TOYOTA TACOMA (RM00U) 97
4 DI36 DIAGNOSTICS EINE (RZFE, 3RZFE) Confirm good connection at. If, replace. 4 Check for short in harness and. 8 E E A75 (b) Turn the ignition switch ON. (c) Select the item DIAGNOSIS/ENHANCED OBD II/DATA Read the temperature value on the handheld tester or OBD II scan tool. : Temperature value: 40 C (40 F) Replace mass air flow meter. 003 TOYOTA TACOMA (RM00U) 98
5 EINE (RZFE, 3RZFE) DI37 5 Check for short in harness or. E E (a) Remove the glove compartment (See page SF55). (b) Disconnect the connector. The mass air flow meter connector is disconnected. (c) Turn the ignition switch ON. (d) Select the item DIAGNOSIS/ENHANCED OBD II/DATA Read the temperature value on the handheld tester or OBD II scan tool. : Temperature value: 40 C (40 F) Connector A378 A0934 A8854 Repair or replace harness or connector. Check and replace (See page IN8). 003 TOYOTA TACOMA (RM00U) 99
DTC P0110/24 Intake Air Temp. Circuit Malfunction
DI30 EINE (JZGE) DI63Q06 DTC P00/4 Temp. Circuit Malfunction CIRCUIT DESCRIPTI Resistance k (Fig. ) 30 0 0 5 3 0.5 0.3 0. 0. Acceptable 0 0 0 40 60 80 00 ( 4) 3 68 04 40 76 Temp. C ( F) The intake air
DTC P0115 Engine Coolant Temperature Circuit. DTC P0117 Engine Coolant Temperature Circuit Low Input
DI58 DIA8Y0 DTC P05 Engine Coolant Temperature Circuit DTC P07 Engine Coolant Temperature Circuit Low Input DTC P08 Engine Coolant Temperature Circuit High Input CICUIT DESCIPTI A thermistor built in the
DTC P0110 Intake Air Temperature Circuit. DTC P0112 Intake Air Temperature Circuit Low Input. DTC P0113 Intake Air Temperature Circuit High Input
DI534 DIAGNOSTICS EINE (2UZFE) DIA8003 DTC P0110 Intake Air Temperature Circuit DTC P0112 Intake Air Temperature Circuit Low Input DTC P0113 Intake Air Temperature Circuit High Input CIRCUIT DESCRIPTION
DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected (Only for 3RZ FE)
DIAGNOSTICS EINE (2RZFE, 3RZFE) DI101 DI12Y16 DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected (Only for 3RZFE) CIRCUIT DESCRIPTION The EGR system recirculates exhaust gas, which is controlled
DTC P0115 ENGINE COOLANT TEMPERATURE CIRCUIT DTC P0117 ENGINE COOLANT TEMPERATURE CIRCUIT LOW INPUT
0577 059VD09 DTC P0115 EINE COOLANT TEMPERATURE CIRCUIT DTC P0117 EINE COOLANT TEMPERATURE CIRCUIT LOW INPUT DTC P0118 EINE COOLANT TEMPERATURE CIRCUIT HIGH INPUT CIRCUIT DESCRIPTION A thermistor is built
DTC P0120 Throttle Position Sensor/Switch A Circuit Malfunction
DI37 DI6V002 DTC P020 Throttle Position Sensor/Switch A Circuit Malfunction CIRCUIT DESCRIPTION Throttle Position Sensor ECM The throttle position sensor is mounted in the throttle body and detects the
DTC P0110 Intake Air Temp. Circuit Malfunction
DI76 EINE (1ZZFE) DI37Z12 DTC P0110 Circuit Malfunction CIRCUIT DESCRIPTI Resistance KΩ (Fig.1) 30 20 10 5 3 2 1 0.5 0.3 0.2 0.1 Acceptable 20 0 20 40 60 80 100 ( 4) 32 68 104 140 176 212 Temp. C ( F)
DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected (Only for 3RZ-FE)
DI68 EINE (2RZFE, 3RZFE) DI12Y12 DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected (Only for 3RZFE) CIRCUIT DESCRIPTI The EGR system recirculates exhaust gas, which is controlled to the proper
DTC P0110 INTAKE AIR TEMPERATURE CIRCUIT DTC P0112 INTAKE AIR TEMPERATURE CIRCUIT LOW INPUT DTC P0113 INTAKE AIR TEMPERATURE CIRCUIT HIGH INPUT
0572 059VE09 DTC P0110 INTAKE AIR TEMPERATURE CIRCUIT DTC P0112 INTAKE AIR TEMPERATURE CIRCUIT LOW INPUT DTC P0113 INTAKE AIR TEMPERATURE CIRCUIT HIGH INPUT CIRCUIT DESCRIPTION Resistance KΩ (Fig.1) 30
DTC P0120 Throttle Pedal Position Sensor/Switch A Circuit (w/ ETCS) DTC P0122 Throttle Pedal Position Sensor/Switch A Circuit Low Input (w/ ETCS)
EINE (5VZFE) DI265 DIB1Q01 DTC P0120 Throttle Pedal Position Sensor/Switch A Circuit (w/ ETCS) DTC P0122 Throttle Pedal Position Sensor/Switch A Circuit Low Input (w/ ETCS) DTC P0123 Throttle Pedal Position
DTC P2120 Throttle/Pedal Position Sensor/Switch D Circuit
EINE DI207 DIAFO02 DTC P2120 Throttle/Pedal Position Sensor/Switch D Circuit *: Only for sequential manual transmission vehicle. CIRCUIT DESCRIPTI The accelerator pedal position sensor is mounted on the
DTC P0120 Throttle/Pedal Position Sensor/Switch A Circuit Malfunction
DI36 EINE (5VZFE) DI1LH14 DTC P0120 Throttle/Pedal Position Sensor/Switch A Circuit Malfunction CIRCUIT DESCRIPTI Throttle position sensor is mounted on the throttle body and it have the 2 sensors to detect
DTC P1300 Igniter Circuit Malfunction (No.1) DTC P1305 Igniter Circuit Malfunction (No.2) DTC P1310 Igniter Circuit Malfunction (No.
DIAGNOSTICS EINE (RZFE, RZFE) DI 9 DI6 DTC P00 Igniter Circuit Malfunction (No.) DTC P05 Igniter Circuit Malfunction (No.) DTC P0 Igniter Circuit Malfunction (No.) DTC P5 Igniter Circuit Malfunction (No.)
DTC P0110 Intake Air Temperature Circuit. DTC P0112 Intake Air Temperature Circuit Low Input. DTC P0113 Intake Air Temperature Circuit High Input
1GR-FE EINE CONTROL SYSTEM SFI SYSTEM 101 DTC P0110 Intake Air Temperature Circuit DTC P0112 Intake Air Temperature Circuit Low Input DTC P0113 Intake Air Temperature Circuit High Input DCRIPTION The Intake
DTC No. DTC Detection Condition Trouble Area
EINE (5VZFE) DI205 DI8YZ02 DTC P0171 System too Lean (Fuel Trim) DTC P0172 System too Rich (Fuel Trim) CIRCUIT DESCRIPTION Fuel trim is related to the feedback compensation value, not to the basic injection
DTC P0120/41 Throttle Position Sensor Circuit Malfunction
DI42 DIAGNOSTICS EINE (2JZGE) DI2S505 DTC P0120/41 Throttle Position Sensor Circuit Malfunction CIRCUIT DESCRIPTI Throttle position sensor is mounted on the throttle body and it have the 2 sensors to detect
DTC P0617 Starter Relay Circuit High
DI390 DIANOSTICS EINE (5VZFE) DIBZ0 DTC P067 Starter Relay Circuit High CIRCUIT DESCRIPTION hile the engine is being cranked, the battery positive voltage is applied to terminal of the ECM. DTC No. DTC
DTC P1120/19 Accelerator Pedal Position Sensor Circuit Malfunction
DIAGNOSTICS EINE (2JZGE) DI103 DI2SE04 DTC P1120/19 Accelerator Pedal Position Sensor Circuit Malfunction CIRCUIT DESCRIPTION Accelerator pedal position sensor is mounted on the throttle body and it have
DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected
DIAGNOSTICS DI95 DI07W03 DTC P040 Exhaust Gas Recirculation Flow Insufficient Detected CIRCUIT DESCRIPTI The EGR system recirculates exhaust gas, which is controlled to the proper quantity to suit the
DTC P0300 Random/Multiple Cylinder Misfire Detected
DIAGNOSTICS EINE (5VZFE) DI57 DI8XH02 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected
DTC P0120 Throttle/Pedal Position Sensor/Switch A Circuit Malfunction
DI184 EINE (JZGTE) DI4SR01 DTC P010 Throttle/Pedal Position Sensor/Switch A Circuit Malfunction CIRCUIT DESCRIPTI Throttle Position Sensor VCC VTA1 IDL1 E + FI6480 The throttle position sensor is mounted
DTC P2237 Oxygen Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)
DI430 EINE (5VZFE) DIB2801 DTC P2237 Oxygen Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1) DTC P2238 Oxygen Sensor Pumping Current Circuit / Low (for A/F sensor) (Bank 1 Sensor
DTC P0300 Random/Multiple Cylinder Misfire Detected
DI56 EINE (2RZFE, 3RZFE) DI8ZU01 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC
DTC P1300 Igniter Circuit Malfunction No.1. DTC P1310 Igniter Circuit Malfunction No.2
DIAGNOSTICS EINE (5SFE) DI63 DI0G06 DTC P300 Igniter Circuit Malfunction No. DTC P30 Igniter Circuit Malfunction No.2 CIRCUIT DESCRIPTION The ECM determines the ignition timing, turns on Tr at a predetermined
DTC P1300 Igniter Circuit Malfunction
DI3 EINE (VZFE) DISD DTC P3 Igniter Circuit Malfunction CIRCUIT DESCRIPTION A Direct Ignition System (DIS) has been adopted. The DIS improves the ignition timing accuracy, reduces highvoltage loss, and
DTC P0300 Random/Multiple Cylinder Misfire Detected
EINE (5VZFE) DI301 DIB1V01 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304
DTC P0351 Ignition Coil A Primary/Secondary Circuit. DTC P0352 Ignition Coil B Primary/Secondary Circuit
DI06 DIAGNOSTICS EINE DIAFC0 DTC P05 A Primary/Secondary Circuit DTC P05 B Primary/Secondary Circuit DTC P05 C Primary/Secondary Circuit DTC P05 D Primary/Secondary Circuit CIRCUIT DESCRIPTION A Direct
DTC P0300 Random/Multiple Cylinder Misfire Detected
DI63 DI7DE01 DTC P0300 Random/Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304 Cylinder 4 Misfire
DTC No. DTC Detection Condition Trouble Area
DI68 EINE (2RZFE, 3RZFE) DIB2B01 DTC P0171 System too Lean (Bank 1) DTC P0172 System too Rich (Bank 1) CIRCUIT DESCRIPTION The fuel trim is related to the feedback compensation value, not to the basic
DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected
DI84 DIAGNOSTICS IN DI01510 DTC P0401 xhaust Gas Recirculation Flow Insufficient Detected CIRCUIT DSCRIPTION The GR system recirculates exhaust gas, which is controlled to the proper quantity to suit the
DTC P0120/41 Throttle Position Sensor Circuit Malfunction
DI42 EINE DI63S01 DTC P0120/41 Throttle Position Sensor Circuit Malfunction CIRCUIT DESCRIPTI Throttle position sensor is mounted on the throttle body and it have the 2 sensors to detect the throttle opening
DTC P0100 Mass or Volume Air Flow Circuit. DTC P0102 Mass or Volume Air Flow Circuit Low Input. DTC P0103 Mass or Volume Air Flow Circuit High Input
DI98 DIGNOSTICS EINE (1GRFE) DIDT801 DTC P0100 Mass or Volume ir Flow Circuit DTC P010 Mass or Volume ir Flow Circuit Low Input DTC P0103 Mass or Volume ir Flow Circuit High Input CIRCUIT DESCRIPTION The
DTC P0134 Oxygen (A/F) Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
DI278 DIAGNOSTICS EINE (5VZFE) DIB1S01 DTC P0134 Oxygen (A/F) Sensor Circuit No Activity Detected (Bank 1 Sensor 1) CIRCUIT DESCRIPTION Refer to DTC P2195 on page DI421. This DTC is related to A/F sensor,
DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected
DIAGNOSTICS EINE (JZGTE) DI17 DI4T301 DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected CIRCUIT DESCRIPTION The EGR system recirculates exhaust gas, which is controlled to the proper quantity
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0110: Intake Air Temperature...
Page 1 of 8 Last Modified: 9-21-2007 Service Category: Engine/Hybrid System 1.6 C Section: Engine Control Model Year: 2008 Model: Tundra Doc ID: RM000000PF3053X Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI
DTC P0171/25 Fuel Trim System too Lean (Air Fuel Ratio Lean Malfunction, Bank1)
EINE (2JZGE) DI71 DI9HM01 DTC P0171/25 Fuel Trim System too Lean (Air Fuel Ratio Lean Malfunction, Bank1) DTC P0174/25 Fuel Trim System too Lean (Air Fuel Ratio Lean Malfunction, Bank2) CIRCUIT DESCRIPTION
DTC P0100 MASS OR VOLUME AIR FLOW CIRCUIT DTC P0102 MASS OR VOLUME AIR FLOW CIRCUIT LOW INPUT DTC P0103 MASS OR VOLUME AIR FLOW CIRCUIT HIGH INPUT
0564 DIAGNOSTICS DTC P0100 MASS OR VOLUME AIR FLOW CIRCUIT 059VF10 DTC P0102 MASS OR VOLUME AIR FLOW CIRCUIT LOW INPUT DTC P0103 MASS OR VOLUME AIR FLOW CIRCUIT HIGH INPUT CIRCUIT DESCRIPTION The MAF (Mass
DTC P0125 Insufficient Coolant Temp. for Closed Loop Fuel Control
DI4 DIAGSTICS EINE DI38404 DTC P05 Insufficient Coolant Temp. for Closed Loop Fuel Control CIRCUIT DESCRIPTION To obtain a high purification rate for the CO, HC and x components of the exhaust gas, a threeway
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
0568 DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 057HV02 DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER 4 MISFIRE
DTC P0171/25 System too Lean (A/F Lean Malfunction, Bank 1) DTC P0172/26 System too Rich (A/F Rich Malfunction, Bank 1) (European spec.
DI66 DIAGNOTIC EINE DI63Y01 DTC P0171/25 ystem too Lean (A/F Lean Malfunction, Bank 1) DTC P0172/26 ystem too Rich (A/F Rich Malfunction, Bank 1) (European spec.) DTC P0174/25 ystem too Lean (A/F Lean
DTC P0122 THROTTLE/PEDAL POSITION SENSOR/SWITCH A CIRCUIT LOW INPUT DTC P0123 THROTTLE/PEDAL POSITION SENSOR/SWITCH A CIRCUIT HIGH INPUT
0584 05DJQ01 DTC P0120 THROTTLE/PEDAL POSITION SENSOR/SWITCH A CIRCUIT DTC P0122 THROTTLE/PEDAL POSITION SENSOR/SWITCH A CIRCUIT LOW INPUT DTC P0123 THROTTLE/PEDAL POSITION SENSOR/SWITCH A CIRCUIT HIGH
DTC P0440 Evaporative Emission Control System Malfunction
DIAGNOSTICS EINE DI81 DI1JZ07 DTC P0440 Evaporative Emission Control System Malfunction CIRCUIT DESCRIPTION The vapor pressure sensor, VSV for canister closed valve (CCV) and VSV for pressure switching
DTC P0441 Evaporative Emission Control System Incorrect. DTC P0446 Evaporative Emission Control System Vent Control Malfunction
DIAGNOSTICS IN (5VZ) DI83 DI8XJ01 DTC P0441 vaporative mission Control System Incorrect Purge low DTC P0446 vaporative mission Control System Vent Control Malfunction CIRCUIT DSCRIPTI The vapor pressure
Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ]
![Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ]](/thumbs/87/96773417.jpg "Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ]")
Last Modified: 7 27 2016 6.6 C Doc ID: RM000000YDP015X Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ] Title: 2UZ FE EINE CONTROL SYSTEM: SFI SYSTEM: P0100,P0102,P0103; Mass Air Flow Circuit
DTC P0010 CAMSHAFT POSITION A ACTUATOR CIRCUIT (BANK 1)
DIAGNOSTICS DTC P0010 CAMSHAFT POSITION A ACTUATOR CIRCUIT (BANK 1) 0543 05AIH08 CIRCUIT DESCRIPTION The Variable Valve Timing (VVT) system includes the ECM, the Oil Control Valve (OCV) and the VVT controller.
DTC P1300 Igniter Circuit Malfunction (No. 1) DTC P1305 Igniter Circuit Malfunction (No. 2) DTC P1310 Igniter Circuit Malfunction (No.
DI DIHD DTC P00 Igniter Circuit Malfunction (No. ) DTC P05 Igniter Circuit Malfunction (No. ) DTC P0 Igniter Circuit Malfunction (No. ) DTC P5 Igniter Circuit Malfunction (No. ) CICUIT DESCIPTION A Direct
DTC 31 Air Flow Circuit Malfunction
EINE (European Spec.) DI1 DIOW15 DTC 1 Air Flow Circuit Malfunction CIRCUIT DESCRIPTION The air flow meter uses a platinum hot wire. The hot wire air flow meter consists of a platinum hot wire, thermistor
DTC P1300 IGNITER CIRCUIT MALFUNCTION (NO.1) DTC P1305 IGNITER CIRCUIT MALFUNCTION (NO.2) DTC P1310 IGNITER CIRCUIT MALFUNCTION (NO.
SFI SYSTEM (ZZFE) DTC P00 IGNITER CIRCUIT MALFUNCTION (NO.) 055 057I50 DTC P05 IGNITER CIRCUIT MALFUNCTION (NO.) DTC P0 IGNITER CIRCUIT MALFUNCTION (NO.) DTC P5 IGNITER CIRCUIT MALFUNCTION (NO.4) CIRCUIT
DTC P1300 Igniter Circuit Malfunction (No.1) DTC P1305 Igniter Circuit Malfunction (No.2) DTC P1310 Igniter Circuit Malfunction (No.
DI0 DIAGNOSTICS EINE DIHD0 DTC P00 Igniter Circuit Malfunction (No.) DTC P05 Igniter Circuit Malfunction (No.) DTC P0 Igniter Circuit Malfunction (No.) DTC P5 Igniter Circuit Malfunction (No.) DTC P0 Igniter
DTC P0031 OXYGEN SENSOR HEATER CONTROL CIRCUIT LOW (BANK 1 SENSOR 1) DTC P0032 OXYGEN SENSOR HEATER CONTROL CIRCUIT HIGH (BANK 1 SENSOR 1)
0530 SFI SYSTEM (2UZFE) DTC P0031 OXYGEN SENSOR HEATER CONTROL CIRCUIT LOW (BANK 1 SENSOR 1) 059UW01 DTC P0032 OXYGEN SENSOR HEATER CONTROL CIRCUIT HIGH (BANK 1 SENSOR 1) DTC P0037 OXYGEN SENSOR HEATER
DTC P0100 MASS AIR FLOW CIRCUIT MALFUNCTION
DIGNOSTICS DTC P0100 MSS IR FLOW CIRCUIT MLFUNCTION 0525 057HI01 CIRCUIT DESCRIPTION The mass air flow meter uses a platinum hot wire. The hot wire air flow meter consists of a platinum hot wire, thermistor
2002 ENGINE PERFORMANCE. Self-Diagnostics - RAV4. Before performing testing procedures, check for any related Technical Service Bulletins (TSBs).
2002 ENGINE PERFORMANCE Self-Diagnostics - RAV4 INTRODUCTION NOTE: Before performing testing procedures, check for any related Technical Service Bulletins (TSBs). To properly diagnosis and repair this
DTC P2237 OXYGEN SENSOR PUMPING CURRENT CIRCUIT/OPEN (FOR A/F SENSOR)(BANK 1 SENSOR 1)
SFI SYSTEM (1GRFE) DTC P2237 OXYGEN SENSOR PUMPI CURRENT CIRCUIT/OPEN (FOR A/F SENSOR)(BANK 1 05207 05AID01 DTC P2238 OXYGEN SENSOR PUMPI CURRENT CIRCUIT LOW (FOR A/F SENSOR)(BANK 1 DTC P2239 OXYGEN SENSOR
DTC P0442 Evaporative Emission Control System Leak Detected (small leak) DTC P0456 Evaporative Emission Control System Leak Detected (very small leak)
DI148 EINE DIAFV01 DTC P0442 Evaporative Emission Control System Leak Detected (small leak) DTC P0456 Evaporative Emission Control System Leak Detected (very small leak) CIRCUIT DESCRIPTI The vapor pressure
DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1)
05114 DIAGNOSTICS 05CRQ04 DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1) CIRCUIT DESCRIPTION Refer to DTC P0130 on page 0596. DTC No. DTC Detecting Condition Trouble Area After
DTC P0100 Mass or Volume Air Flow Circuit. DTC P0102 Mass or Volume Air Flow Circuit Low Input. DTC P0103 Mass or Volume Air Flow Circuit High Input
94 TR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0100 Mass or Volume Air Flow Circuit DTC P010 Mass or Volume Air Flow Circuit Low Input DTC P0103 Mass or Volume Air Flow Circuit High Input DCRIPTION The Mass
DTC P0451 EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH RANGE/PERFORMANCE
DTC P0451 EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH RANGE/PERFORMANCE 05255 052NT23 DTC P0452 EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH LOW INPUT DTC P0453 EVAPORATIVE
DTC P2118 THROTTLE ACTUATOR CONTROL MOTOR CURRENT RANGE/PERFORMANCE
0560 05NY0 DTC P8 THROTTLE ACTUATOR CONTROL MOTOR CURRENT RANGE/PERFORMANCE CIRCUIT DESCRIPTION The Electronic Throttle Control System (ETCS) has a dedicated power supply circuit. The voltage () is monitored
ENGINE (3RZ FE) HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot in accordance with the procedure on the following page.
EINE (3RZFE) EINE (3RZFE) HOW TO PROCEED WITH TROUBLESHOOTI Troubleshoot in accordance with the procedure on the following page. DI1 DI0T50 1 Vehicle Brought to Workshop Customer Problem Analysis P. DI
DTC P0451(A) EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH RANGE/PERFORMANCE
05210 DTC (A) EVAPORATIVE EMISSION CONTROL RANGE/PERFORMANCE 052NT12 DTC P0452 EVAPORATIVE EMISSION CONTROL LOW INPUT DTC P0453 EVAPORATIVE EMISSION CONTROL HIGH INPUT CIRCUIT DESCRIPTION The vapor pressure
DTC P0171 SYSTEM TOO LEAN (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2)
05498 DIAGNOSTICS DTC P0171 SYSTEM TOO LEAN (BANK 1) 05EXR06 DTC P0172 SYSTEM TOO RICH (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2) DTC P0175 SYSTEM TOO RICH (BANK 2) CIRCUIT DESCRIPTION The fuel trim is
DTC P0100 Mass or Volume Air Flow Circuit. DTC P0102 Mass or Volume Air Flow Circuit Low Input. DTC P0103 Mass or Volume Air Flow Circuit High Input
GR-FE EINE CONTROL SYSTEM SFI SYSTEM 95 DTC P000 Mass or Volume Air Flow Circuit DTC P00 Mass or Volume Air Flow Circuit Low Input DTC P003 Mass or Volume Air Flow Circuit High Input DCRIPTION The Mass
DTC P0440 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION DTC P0442 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION
0536 SFI SYSTEM (ZZGE) DTC P0440 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION 057I003 DTC P044 EVAPORATIVE EMISSION CONTROL SYSTEM MALFUNCTION CIRCUIT DESCRIPTION The vapor pressure sensor, VSV for
DTC P0617 STARTER RELAY CIRCUIT HIGH
0534 DTC P067 STARTER RELAY CIRCUIT HIGH 05DJY0 MONITOR DESCRIPTION While the engine is being cranked, the battery positive voltage is applied to terminal STA of the ECM. If the ECM detects the starter
DTC P1613 Secondary Air Injection Driver Malfunction
280 2TR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC Secondary Air Injection Driver Malfunction DCRIPTION Refer to DTC P0412 (See page -189). DTC No. DTC Detection Conditions Trouble Areas Either of following
Fuel Pump Control Circuit
DI448 DIAGNOSTICS EINE (5VZFE) DI8Z003 Fuel Pump Control Circuit CIRCUIT DESCRIPTI In the diagram below, when the engine is cranked, current flows from terminal ST of the ignition switch to the starter
1/11/2018 R.M. 2003::Diagnostics: SFI System: P1300, P1305, P1310, P1315 Igniter Circuit Malfunction (Corolla) 2003 Toyota Corolla MotoLogic
2003 Corolla DTC P1300 IGNITER CIRCUIT MALFUNCTION(NO.1) Report a problem with this article DTC P1305 IGNITER CIRCUIT MALFUNCTION(NO.2) DTC P1310 IGNITER CIRCUIT MALFUNCTION(NO.3) DTC P1315 IGNITER CIRCUIT
Camshaft Position "A" Actuator Circuit (Bank 1)
72 2TR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) HINT: This DTC relates to the Oil Control Valve (OCV). DCRIPTION The Variable Valve Timing (VVT) system
DTC P0505 IDLE AIR CONTROL SYSTEM DTC P0511 IDLE AIR CONTROL CIRCUIT CIRCUIT DESCRIPTION
0528 DIAGNOSTICS 05DJX0 DTC P0505 IDLE AIR CONTROL SYSTEM DTC P05 IDLE AIR CONTROL CIRCUIT CIRCUIT DESCRIPTION From Air Cleaner Signal ECM Throttle Valve Intake Air Chamber The rotary solenoid type idle
DTC P0300/93 Random/Multiple Cylinder Misfire Detected (European spec.) DTC P0301/93 Cylinder 1 Misfire Detected (European spec.)
DI7 DI63Z0 DTC P0300/93 Random/Multiple Cylinder Misfire Detected (European spec.) DTC P030/93 Cylinder Misfire Detected (European spec.) DTC P030/93 Cylinder Misfire Detected (European spec.) DTC P0303/93
4/24/2017 A L L Diagnostic Trouble Codes ( DTC ) Testing and Inspection, P Code Charts: P0441
Vehicle» A L L Diagnostic Trouble Codes ( DTC )» Testing and Inspection» P Code Charts» P0441 DTC P0441 Evaporative Emission Control System Incorrect Purge Flow CIRCUIT DESCRIPTION http://repair.alldata.com/alldata/article/display.action?componentid=3926&itypeid=423&nonstandardid=2379425&vehicleid=38048&windowname=mainadonlin
1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM
72 1GR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC DTC P0010 P0020 Camshaft Position "A" Actuator Circuit (Bank 1) Camshaft Position "A" Actuator Circuit (Bank 2) HINT: This DTC relates to the Oil Control Valve
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 0539 059VJ09 DTC P030 CYLINDER MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER 4 MISFIRE
DI 3 ENGINE DIAGNOSTICS DI PRE CHECK
FI0534 PRECHECK DI3 DI09603 1. DIAGNOSIS SYSTEM (a) Description When troubleshooting OBD II vehicles, the only difference from the usual troubleshooting procedure is that you connect to the vehicle the
DTC P050A Cold Start Idle Air Control System Performance
2UZ-FE EINE CONTROL SYSTEM SFI SYSTEM 273 DTC P050A Cold Start Idle Air Control System Performance DCRIPTION The Electronic Throttle Control System (ETCS) controls the engine idling speed. The ETCS operates
DTC P0300 Random / Multiple Cylinder Misfire Detected. DTC P0301 Cylinder 1 Misfire Detected. DTC P0302 Cylinder 2 Misfire Detected
1GR-FE EINE CONTROL SYSTEM SFI SYSTEM 171 DTC P0300 Random / Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P030 Cylinder Misfire Detected DTC P0303 Cylinder 3 Misfire Detected
DTC P0335 Crankshaft Position Sensor "A" Circuit
2TR-FE EINE CONTROL SYSTEM SFI SYSTEM 77 DTC P0335 Crankshaft Position Sensor "A" Circuit DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent DCRIPTION The Crankshaft Position (CKP) sensor system
DTC P0657 Actuator Supply Voltage Circuit / Open
1GR-FE EINE CONTROL SYSTEM SFI SYSTEM 277 DTC P0657 Actuator Supply Voltage Circuit / Open MONITOR DCRIPTION The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 05157 059VJ13 DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER 4
Throttle Actuator Control Motor Current Range / Performance
TR-FE EINE CONTROL SYSTEM SFI SYSTEM 99 DTC P8 Control Motor Current Range / Performance DCRIPTION The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage () is
DTC P0300 Random / Multiple Cylinder Misfire Detected
162 DTC P0300 Random / Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304 Cylinder 4 Misfire
DTC P1300/14 Igniter Circuit Malfunction No.1. DTC P1310/15 Igniter Circuit Malfunction No.2. DTC P1320/14 Igniter Circuit Malfunction No.
DI68 DIAGNOTIC EINE DIIO06 DTC P00/4 Igniter Circuit Malfunction No. DTC P0/5 Igniter Circuit Malfunction No. DTC P0/4 Igniter Circuit Malfunction No. CIRCUIT DECRIPTION A DI (Direct Ignition ystem) has
DTC P0505: IDLE AIR CONTROL (IAC) SYSTEM CIRCUIT
Page 1 of 5 DTC P0505: IDLE AIR CONTROL (IAC) SYSTEM CIRCUIT CAUTION: If ECM replacement is instructed in following testing, always ensure ECM connectors and ground circuit are okay. If either are suspect,
2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
160 2UZ-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0171 System Too Lean (Bank 1) DTC P0172 System Too Rich (Bank 1) DTC P0174 System Too Lean (Bank 2) DTC P0175 System Too Rich (Bank 2) DCRIPTION The fuel
DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1)
05 120 05CRQ 02 DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1) CIRCUIT DESCRIPTION Refer to DTC P0130 on page 05 101. DTC No. DTC Detecting Condition Trouble Area P0134 After engine
DTC P0300 Random / Multiple Cylinder Misfire Detected. DTC P0301 Cylinder 1 Misfire Detected. DTC P0302 Cylinder 2 Misfire Detected
1GR-FE EINE CONTROL SYSTEM SFI SYSTEM 169 DTC P0300 Random / Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire
1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM. DTC P0332 Knock Sensor 2 Circuit Low Input (Bank 2) DTC P0333 Knock Sensor 2 Circuit High Input (Bank 2)
84 GR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC DTC P037 P038 Knock Sensor Circuit Low Input (ank or Single Sensor) Knock Sensor Circuit High Input (ank or Single Sensor) DTC P033 Knock Sensor Circuit Low
1. Connect the Honda PGM Tester or an OBD II scan tool to the 16P Data Link Connector (DLC) located behind the right side of the center console.
Troubleshooting Procedures I. How To Begin Troubleshooting When the Malfunction indicator Lamp (MIL) has been reported on, or there is a driveability problem, use the appropriate procedure below to diagnose
DTC P0171 SYSTEM TOO LEAN (BANK 1) DTC P0172 SYSTEM TOO RICH (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2) DTC P0175 SYSTEM TOO RICH (BANK 2)
05155 05NZ501 DTC P0171 SYSTEM TOO LEAN (BANK 1) DTC P0172 SYSTEM TOO RICH (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2) DTC P0175 SYSTEM TOO RICH (BANK 2) CIRCUIT DESCRIPTION These DTCs indicate that the
1ZZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM. DTC P0300 Random / Multiple Cylinder Misfire Detected ECM
164 DTC P0300 Random / Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304 Cylinder 4 Misfire
DTC P050A Cold Start Idle Air Control System Performance. DTC P050B Cold Start Ignition Timing Performance
278 2UZ-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P050A Cold Start Idle Air Control System Performance DTC P050B Cold Start Ignition Timing Performance DCRIPTION The Electronic Throttle Control System (ETCS)
Model Year: 2007 Model: Tacoma Doc ID: RM H800NX
Page 1 of 12 Last Modified: 5-7-2008 5.1 C From: 200608 Model Year: 2007 Model: Tacoma Doc ID: RM0000013H800NX Title: 2TR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P2A00: A/F Sensor Circuit Slow Response (Bank
DIAGNOSTIC TROUBLE CODE CHART
18 Cruise Control System DIAGNOSTIC TROUBLE CODE CHART If a trouble code is indicated while checking DTCs, inspect the listed for that code in the table below, and proceed to the applicable page. DTC No.
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 05 149 059VJ 07 DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER
4/17/2018 2AZ-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0031,P0032: Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)
2007 Camry LE (L4) Report a problem with this article Last Modified: 2010-6-11 00:00:00 C From:200601 Model Year: 2007 Model: Camry Doc ID: RM000000WC101DX Engine Family: 2AZ-FE Body Type: 4Dr. Sedan VDS:
DI 3 ENGINE DIAGNOSTICS DI00H 22 PRE CHECK
PRECHECK DI3 DI00H22 1. DIAGNOSIS SYSTEM (a) Description When troubleshooting OBD II vehicles, the only difference from the usual troubleshooting procedure is that you connect to the vehicle the OBD II
Model Year: 2008 Model: ES350 Doc ID: RM000000PFA04GX
1 of 13 Last Modified: 7-13-2007 Service Category: Engine/Hybrid System 1.6 C Section: Engine Control Model Year: 2008 Model: ES350 Doc ID: RM000000PFA04GX Title: 2GR-FE EINE CONTROL SYSTEM: SFI SYSTEM:
DTC B1156/B1157/15 Front Airbag Sensor (RH) Malfunction
DI309 DI6PW03 DTC B1156/B1157/15 Malfunction CIRCUIT DESCRIPTION The front airbag sensor (RH) circuit consists of the airbag sensor assembly and front airbag sensor (RH). For details of the function of
DTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2)
05122 DIGNOSTICS DTC P0136 OXYGEN SENSOR CIRCUIT MLFUNCTION (NK 1 SENSOR 2) 05CRR03 CIRCUIT DESCRIPTION Refer to DTC P0130 on page 0596. DTC No DTC Detection Condition Trouble rea P0136 The following condition
G - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.