2006 MINI Cooper ENGINE Engine - Technical Data - Cooper (W10) & Cooper S (W11) Engine - Technical Data - Cooper (W10) & Cooper S (W11)

Size: px
Start display at page:

Download "2006 MINI Cooper ENGINE Engine - Technical Data - Cooper (W10) & Cooper S (W11) Engine - Technical Data - Cooper (W10) & Cooper S (W11)"

Transcription

1 ENGINE, GENERAL ENGINE IN GENERAL ENGINE Engine - Technical Data - Cooper (W10) & Cooper S (W11) ENGINE IN GENERAL Cylinder 4 Bore mm 77 (3.03) Stroke mm 85.8 (3.377) Effective displacement cm Compression ratio (W10) : Compression ratio (W11) :1 8.3 Maximum permissible speed (fuel rpm 7000 shutoff) Permissible continuous speed (red rpm 6750 area) Compression pressure bar (approximately equal for all Cylinders) (W10) Compression pressure (approximately equal for all Cylinders) (W11) bar ENGINE BLOCK ENGINE IN GENERAL Information is identical to ENGINE IN GENERAL CAMSHAFT Information is identical to CAMSHAFT CONNECTING RODS AND BEARINGS Information is identical to CONNECTING RODS AND BEARINGS. Information is identical to.

2 Information is identical to CYLINDER HEAD WITH COVER Information is identical to CYLINDER HEAD WITH COVER CYLINDER HEAD WITH VALVE SEAT COVER Information is identical to CYLINDER HEAD WITH VALVE SEAT COVER ENGINE BLOCK (CRANKCASE) ENGINE BLOCK (CRANKCASE) SPECIFICATIONS Bore dia. a) mm Permitted out-of-round of cylinder mm bore a) Permitted conicity of cylinder bore mm a) Permissible total wear tolerance mm 0.10 between piston and cylinder (engine operated) Information is identical to. Information is identical to VALVES WITH SPRINGS Information is identical to VALVES WITH SPRINGS. CYLINDER HEAD WITH COVER CAMSHAFT Information is identical to CAMSHAFT CONNECTING RODS AND BEARINGS Information is identical to CONNECTING RODS AND BEARINGS.

3 Information is identical to. Information is identical to CYLINDER HEAD WITH COVER0 CYLINDER HEAD WITH COVER SPECIFICATIONS Inside diameter of installed valve mm guide Running clearance between valve and valve guide Inlet mm Exhaust mm Maximum running clearance mm between valve and valve guide (inlet) Maximum running clearance mm between valve and valve guide (exhaust) Wear limit (inlet) mm 0.25 Wear limit (exhaust) mm CYLINDER HEAD WITH VALVE SEAT COVER CYLINDER HEAD WITH VALVE SEAT COVER W10 SPECIFICATIONS Valve seat angle 45 Correction angle: outer 15 Correction angle: inner 75 Valve seat width: Inlet mm Valve seat width: outer mm Valve seat bore diameter Valve seat surface: Outside dia. mm inlet Valve seat surface: Outside dia. mm exhaust CYLINDER HEAD WITH VALVE SEAT COVER W11 SPECIFICATIONS Valve seat angle 45 Correction angle: outer 15 Correction angle: inner 65.25

4 Valve seat width: Inlet mm Valve seat width: outer mm Valve seat bore diameter Valve seat surface: Outside dia. mm inlet Valve seat surface: Outside dia. exhaust mm Information is identical to. Information is identical to VALVES WITH SPRINGS Information is identical to VALVES WITH SPRINGS. CRANKSHAFT WITH BEARING CAMSHAFT Information is identical to CAMSHAFT CONNECTING RODS AND BEARINGS Information is identical to CONNECTING RODS AND BEARINGS. CRANKSHAFT AND BEARINGS SPECIFICATIONS (MAIN) Diameters of main journals mm Radial play of main bearings mm Radial play of main bearings mm 0.70 (wear limit) Axial play of crankshaft mm Axial play of crankshaft (wear mm 0.30 limit) CRANKSHAFT AND BEARINGS SPECIFICATIONS (CONROD)

5 Diameters of conrod bearing mm journals (W10) Diameters of conrod bearing mm journals (W11) Radial play of conrod bearings mm Radial play of conrod bearings (wear limit) mm Information is identical to. Information is identical to VALVES WITH SPRINGS R50 Information is identical to VALVES WITH SPRINGS R50. CONNECTING ROD WITH BEARING CAMSHAFT R50 Information is identical to CAMSHAFT R CONNECTING RODS AND BEARINGS CONNECTING RODS AND BEARINGS SPECIFICATIONS Conrod bushing: Inside diameter mm (W10) Conrod bushing: Inside diameter mm (W11) Running clearance between smallend mm bushing and piston pin Wear limit mm 0.07 Information is identical to. Information is identical to.

6 11 34 VALVES WITH SPRINGS R50 Information is identical to VALVES WITH SPRINGS R50. PISTON WITH RINGS AND PIN CAMSHAFT R50 Information is identical to CAMSHAFT R50. PISTONS WITH RINGS AND PINS R50 SPECIFICATIONS Pistons and pins are matched - only replace together in pairs Measuring point "A" (position) mm Piston diameter at measuring point "A" Original (new dimension) mm Piston running clearance mm Permissible total play between mm 0.15 piston and cylinder (engine operated) PISTONS WITH RINGS AND PINS SPECIFICATIONS 1st groove End clearance mm Contact clearance (wear limit) mm 0.8 Axial play mm nd groove End clearance mm Contact clearance (wear limit) mm 1.0 Axial play mm rd groove End clearance mm Contact clearance (wear limit) mm 1.0 Axial play mm VALVES WITH SPRINGS R50 Information is identical to VALVES WITH SPRINGS R50.

7 CAMSHAFT ENGINE IN GENERAL R50 / W10 / COOPER Information is identical to ENGINE IN GENERAL R50 / W10 / COOPER CAMSHAFT CAMSHAFT SPECIFICATIONS Diameters of bearings mm Radial runout mm Wear limit: Radial runout mm 0.12 Axial play mm Wear limit: Axial play mm 0.40 VALVES WITH SPRINGS VALVES WITH SPRINGS VALVES WITH SPRINGS W10 SPECIFICATIONS Stem bore diameter Inlet mm Exhaust mm Valve (length) Inlet mm Exhaust mm VALVES WITH SPRINGS W11 SPECIFICATIONS Stem bore diameter Inlet mm Exhaust mm Exhaust mm Valve (length) Inlet mm Exhaust mm OIL SUPPLY OIL SUPPLY R50 / W10 OIL SUPPLY SPECIFICATIONS Oil grades and consumption: refer

8 to appropriate OPERATING FLUIDS article in GENERAL INFORMATION. Oil change volume with oil filter (W10) Oil change volume with oil filter (W11) Liters 4.5 Liters 4.8 OIL PUMP WITH FILTER AND DRIVE CAMSHAFT R50 Information is identical to CAMSHAFT R CONNECTING RODS AND BEARINGS R50 Information is identical to CONNECTING RODS AND BEARINGS R50. R50 Information is identical to R50. R50 Information is identical to R CYLINDER HEAD WITH COVER R50 Information is identical to CYLINDER HEAD WITH COVER R CYLINDER HEAD WITH VALVE SEAT COVER R50 Information is identical to CYLINDER HEAD WITH VALVE SEAT COVER R ENGINE BLOCK (CRANKCASE) R50 Information is identical to ENGINE BLOCK (CRANKCASE) R50. Information is identical to. Information is identical to.

9 11 34 VALVES WITH SPRINGS R50 Information is identical to VALVES WITH SPRINGS R OIL PUMP WITH SUCTION ELEMENT AND DRIVE OIL PUMP WITH SUCTION ELEMENT AND DRIVE SPECIFICATIONS Oil pressure at idle speed and bar 0.25 engine at operating temperature Oil pressure at 3000 rpm bar

Refer to procedure. Note: Engine; Tightening torque. Service and Repair; Disassembly and Assembly. 25 Nm. Note: Engine.

Refer to procedure. Note: Engine; Tightening torque. Service and Repair; Disassembly and Assembly. 25 Nm. Note: Engine. Engine Cylinder head Refer to procedure Note: Engine; Service and Repair; Disassembly and Assembly Refer to procedure Note: Engine; Service and Repair; Disassembly and Assembly Head bolt reuse/replace

More information

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through

More information

GENERAL SPECIFICATION STABLE

GENERAL SPECIFICATION STABLE 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Thursday,

More information

PISTON AND CONNECTING ROD

PISTON AND CONNECTING ROD 42 02 PISTON AND CONNECTING ROD 1. No.1 compression ring 2. No.2 compression ring 3. Oil ring Description Cylinder bore diameter Piston outer diameter (D1) Clearance between bore and piston Piston cooling

More information

MAINTENANCE STANDARDS TABLE

MAINTENANCE STANDARDS TABLE TABLE 4 MAINTENANCE STANDARDS TABLE Unit: mm [in.] ( Maximum rpm, (no-load) Minimum rpm, (no-load) According to engine specification Adjust governor setting. Compression pressure MPa (kgf/cm 2 ) [psi]

More information

Shown on engine Locating plate for right camshaft 6 Slot in camshaft Inspect basic position of balancing shaft only engine 112

Shown on engine Locating plate for right camshaft 6 Slot in camshaft Inspect basic position of balancing shaft only engine 112 AR05.10-P-6858V Check the engine valve timing 7.12.05 ENGINE 112 ENGINE 113.962 in MODEL 463.206 /240 /241 /247 /248 /249 /254 ENGINE 113.982 in MODEL 463.243 /246 ENGINE 113 (except 113.995) in MODEL

More information

Unit: mm (in) ITEM STANDARD LIMIT IN. 33 (1.3) EX.

Unit: mm (in) ITEM STANDARD LIMIT IN. 33 (1.3) EX. Model: DR650SEL0 E-03, 24, 28, 33 Date: July 16, 2009 SERVICE DATA VALVE + GUIDE Valve diam. Valve clearance (when engine is cold) Valve guide to valve stem clearance Valve stem deflection Valve guide

More information

20 C (68 F) Ω C (68 86 F)

20 C (68 F) Ω C (68 86 F) Page 1 of 10 Service Data 0C Emission Control Devices EVAP system purge control solenoid valve power supply (If equipped) EVAP system purge control solenoid valve resistance (If equipped) PAIR control

More information

TECHNICAL DATA - ENGINE 250/400/450/525 SX,MXC,EXC RACING 2005

TECHNICAL DATA - ENGINE 250/400/450/525 SX,MXC,EXC RACING 2005 10-20E TECHNICAL DATA - ENGINE 250/400/450/525 SX,MXC,EXC RACING 2005 TYPE 250 EXC 400 EXC 450 SX 450 MXC 450 EXC 525 SX 525 MXC-G 525 EXC 525 MXC DESERT Design Liquid-cooled single cylinder 4-stroke engine

More information

Displacement 5.3L 325 CID. Stroke 92.0 mm in. Firing Order Spark Plug Gap 1.02 mm 0.04 in

Displacement 5.3L 325 CID. Stroke 92.0 mm in. Firing Order Spark Plug Gap 1.02 mm 0.04 in Enge Mechanical Specifications (RPO LMG VIN 0) Specification Application Metric English General Enge Type V8 Displacement 5.3L 325 CID RPO LMG VIN 0 Bore 96.0-96.018 3.779-3.78 Stroke 92.0 3.622 Compression

More information

CRANKSHAFT REAR RADIAL SEAL

CRANKSHAFT REAR RADIAL SEAL 1B-38 CRANKSHAFT REAR RADIAL SEAL Preceding Work: Removal of flywheel or drive plate 1. Special tool 2. Special tool 3. Crankshaft rear seal Tools Required W9911 0020B (601 589 03 43 00) Crankshaft Rear

More information

1.6L 4-CYL - VIN [E]

1.6L 4-CYL - VIN [E] 1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES

More information

ENGINE MECHANICAL (4A FE)

ENGINE MECHANICAL (4A FE) Maintenance, Engine Mechanical (4AFE) A3 Chassis Brake pads and disc Pad thickness Disc thickness Disc runout Brake linings and drums Lining thickness Drum inside diameter Front Rear Front Rear Drum brake

More information

ENGINE SPECS COMMON SPECIFICATIONS & PROCEDURES LEGACY & OUTBACK COMMON SPECIFICATIONS & PROCEDURES

ENGINE SPECS COMMON SPECIFICATIONS & PROCEDURES LEGACY & OUTBACK COMMON SPECIFICATIONS & PROCEDURES 1Search Print Date: 17/01/017 ENGINE SPECS COMMON SPECIFICATIONS & PROCEDURES LEGACY & OUTBACK COMMON SPECIFICATIONS & PROCEDURES 015 Subaru Legacy 3.6L Eng 3.6R Limited System Specification/Procedure

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 4168 OVERHAUL 410F701 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 to 0.40 mm (0.0039 to 0.0157 in.) 0.40 mm (0.0157 in.) C80538 2. INSPECT

More information

CURSOR SERIES C10. Industrial application C10 ENT

CURSOR SERIES C10. Industrial application C10 ENT CURSOR SERIES Industrial application C10 C10 ENT This publication describes the characteristics, data and correct methods for repair operations on each component of the vehicle. If the instructions provided

More information

CRANKSHAFT. Preceding Works: Removal of end cover Removal of pistons Removal of crankshaft sprocket

CRANKSHAFT. Preceding Works: Removal of end cover Removal of pistons Removal of crankshaft sprocket 30 02 CRANKSHAFT Preceding Works: Removal of end cover Removal of pistons Removal of crankshaft sprocket 1. Crankshaft main bearing shells, upper 2. Upper thrust bearing 3. Crankshaft 4. Crankshaft main

More information

Piston diameter should be measured at normal room temperature of 70 F (21 C).

Piston diameter should be measured at normal room temperature of 70 F (21 C). Piston & Rod Assembly 1. Pistons are not interchangeable from bank to bank. Pistons are marked L and R (left and right) and must be installed with arrow on top of piston pointing toward front of engine.

More information

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder Removal & Installation See VALVE SPRINGS under CYLINDER HEAD under OVERHAUL. CAMSHAFT Removal 1. Rotate crankshaft until "0" mark on flywheel aligns with timing mark on flywheel cover. Remove inspection

More information

1999 Acura SLX. Fig. 6: Identifying Piston & Connecting Rod Size Courtesy of ISUZU MOTOR CO.

1999 Acura SLX. Fig. 6: Identifying Piston & Connecting Rod Size Courtesy of ISUZU MOTOR CO. 3. Check cylinder bore to determine piston-to-cylinder clearance. Clearance should be within specification. See PISTONS, PIN & RINGS table under ENGINE SPECIFICATIONS. Fig. 6: Identifying Piston & Connecting

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 1 1 38-13 SUBJECT DATE Inspection of the Main and Connecting Rod Bearings In-Chassis January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Inspection of

More information

SERVICE DATA. Unit: mm (in) ITEM STD/SPEC. LIMIT Valve diam. 29 IN. (1.14) EX IN. ( ) EX.

SERVICE DATA. Unit: mm (in) ITEM STD/SPEC. LIMIT Valve diam. 29 IN. (1.14) EX IN. ( ) EX. 4 STROKE VALVE + GUIDE SERVICE DATA Date: November 23, 2000 Valve diam. 29 (1.14) 24 (0.94) Valve clearance (when cold) 0.10 0.20 (0.004 0.008) 0.20 0.30 (0.008 0.012) Valve guide to valve stem 0.010 0.037

More information

ENGINE MECHANICAL SPECIFICATIONS

ENGINE MECHANICAL SPECIFICATIONS GENERAL DESCRIPTION The 1955 Cadillac engine is of the V-8,overhead valve design, with a 3-13/16" bore and a 3-5/8" stroke to provide a piston displacement of 331 cubic inches. The compression ratio is

More information

Removing and installing/replacing all pistons (S54)

Removing and installing/replacing all pistons (S54) 11 25 530 Removing and installing/replacing all pistons (S54) (engine removed) Removal Removal of pistons is described separately from installation. Assembly sequence for removal and installation is different.

More information

ENGINE SPECS COMMON SPECS & PROCEDURES FORESTER COMMON SPECIFICATIONS & PROCEDURES

ENGINE SPECS COMMON SPECS & PROCEDURES FORESTER COMMON SPECIFICATIONS & PROCEDURES 1Search Print Date: 17/01/017 ENGINE SPECS COMMON SPECS & PROCEDURES FORESTER COMMON SPECIFICATIONS & PROCEDURES 015 Subaru Forester.5L Eng.5i Touring System Specification/Procedure Air Conditioning Service

More information

service bulletin MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications No. 91-6

service bulletin MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications No. 91-6 service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-6 MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications NOTE: Generation V Engines Have the Fuel Pump Mounted on the

More information

Motorcycle 2012 Model: LS650L2 Date: May 2011

Motorcycle 2012 Model: LS650L2 Date: May 2011 LS650L2 Motorcycle 2012 Model: LS650L2 Date: May 2011 MSRP $5,399 Metallic Fox Orange / Glass Sparkle Black (JGS) Key Features 1. 652cm3 (39.8 cu. in), 4-stroke, air-cooled, SOHC engine with Twin Swirl

More information

Advanced Auto Tech. ASE A 1 Test Preparation Engine Lower End Theory & Service

Advanced Auto Tech. ASE A 1 Test Preparation Engine Lower End Theory & Service Advanced Auto Tech ASE A 1 Test Preparation Engine Lower End Theory & Service To make work easier, one of the first steps often done before engine removal is to clean & degrease the engine compartment.

More information

Updated 26th September 2017

Updated 26th September 2017 TECHNICAL DATA ENGINE SECTION TDP e259 General... 2 Cylinder Block... 3 Cylinder Head... 3 Valves & Springs... 3 Camshafts... 3 Pistons... 3 Connecting Rods... 4 Crankshaft... 4 Oil Pump... 4 Coolant Thermostat...

More information

SECTION C Engine 6.4L Diesel

SECTION C Engine 6.4L Diesel 303-01C-i Engine 6.4L Diesel 303-01C-i SECTION 303-01C Engine 6.4L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 6.4L Diesel 303-01C-2 SPECIFICATIONS Material Gasket Maker TA-16 Motorcraft

More information

SERVICE DATA. Item Standard Limit Valve diam. IN (1.42) EX (1.30) Tappet clearance (When cold)

SERVICE DATA. Item Standard Limit Valve diam. IN (1.42) EX (1.30) Tappet clearance (When cold) Model: LT-A750XK9 P-17, 24, 28, 33 LT-A750XZK9 P-17, 28, 33 4 STROKE Camshaft + Cylinder Head SERVICE DATA Valve + Guide Valve diam. IN. 36.0 (1.42) EX. 33.0 (1.30) Tappet clearance (When cold) IN. 0.10

More information

FORD V8 ENGINES 209. the treated area, the block is cracked and should be replaced.

FORD V8 ENGINES 209. the treated area, the block is cracked and should be replaced. FORD V8 ENGINES 209 Cylinder block Core plug Strike here with hammer Drift 8 the treated area, the block is cracked and should be replaced. 3. Check flatness of the cylinder block deck. Place an accurate

More information

I. TWO-STROKE MECHANICAL EN- GINE PARTS

I. TWO-STROKE MECHANICAL EN- GINE PARTS I. TWO-STROKE MECHANICAL EN- GINE PARTS 1. UNIBLOCK ENGINES (AV520-600-750-125) a) INTRODUCTION Fig. 1 shows the short block. Fig. 2 shows an exploded view of the engine. As may be seen the momoblock is

More information

SERVICING SPECIFICATIONS (1) ENGINE BODY

SERVICING SPECIFICATIONS (1) ENGINE BODY SERVICING SPECIFICATIONS (1) ENGINE BODY (1/14) Lubricating oil capacity Oil pan depth 124 mm (4.88 in.) 7.0 L 1.85 U.S.gals. 1.54 lmp.gals. 9.5 L 2.51 U.S.gals. 2.09 lmp.gals. Oil pan depth 90 mm (3.54

More information

ENGINE SPECS COMMON SPECS & PROCEDURES FORESTER COMMON SPECIFICATIONS & PROCEDURES

ENGINE SPECS COMMON SPECS & PROCEDURES FORESTER COMMON SPECIFICATIONS & PROCEDURES 1Search Print Date: 17/01/017 ENGINE SPECS COMMON SPECS & PROCEDURES FORESTER COMMON SPECIFICATIONS & PROCEDURES 014 Subaru Forester.0L Eng.0XT Premium System Specification/Procedure Air Conditioning Service

More information

Section 10 Chapter 20

Section 10 Chapter 20 Section 10 Chapter 20 24 Valve, 8.3 Liter Engine Specifications Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cuins engine codes. These engine codes have no meaning to New Holland

More information

SHOP MANUAL CASE/INTERNATIONAL MODELS 235, 235H, 245, 255, 265 & 275

SHOP MANUAL CASE/INTERNATIONAL MODELS 235, 235H, 245, 255, 265 & 275 SHOP MANUAL CASE/INTERNATIONAL MODELS 235, 235H,,, & 2 The tractor model number and product identification (seriai) number is on a plate iocated on the right side of the front frame raii. The engine seriai

More information

SERVICING SPECIFICATIONS (1) ENGINE BODY

SERVICING SPECIFICATIONS (1) ENGINE BODY SERVICING SPECIFICATIONS (1) ENGINE BODY (1/14) Lubricating oil capacity Cylinder head surface Oil pan depth 121 mm (4.76 in.) Oil pan depth 101 mm (3.98 in.) 2.5 L 0.66 U.S.gals. 0.55 lmp.gals. 3.8 L

More information

4 Stroke Diesel. Oil type SAE 15 W40/E 3

4 Stroke Diesel. Oil type SAE 15 W40/E 3 MARCH 2006 TECHNICAL DATA 2.33 GENERAL SPECIFICATIONS Cycle Air supply Injection 4 Stroke Diesel naturally aspirated direct Number of cylinders 4 in line 6 in line Bore mm 104 Stroke mm 132 Total displacement

More information

SERVICE DATA. Unit: mm (in) ITEM STANDARD LIMIT Valve diam. IN (1.42) EX ( ) EX.

SERVICE DATA. Unit: mm (in) ITEM STANDARD LIMIT Valve diam. IN (1.42) EX ( ) EX. 4 STROKE VALVE + VALVE GUIDE CAMSHAFT + CYLINDER HEAD SERVICE DATA Valve diam. 36.0 (1.42) 33.0 (1.30) Tappet clearance (when cold) 0.10 0.20 (0.004 0.008) 0.20 0.30 (0.008 0.012) Valve guide to valve

More information

SERVICING SPECIFICATIONS (1) ENGINE BODY

SERVICING SPECIFICATIONS (1) ENGINE BODY SERVICING SPECIFICATIONS (1) ENGINE BODY Lubricating oil capacity Oil pan depth 110 mm (4.33 in.) 5.7 L 1.5 U.S.gals (1/14) Oil pan depth 125 mm (4.92 in.) 5.1 L 1.3 U.S.gals Oil pan depth 130 mm (5.12

More information

K EN R A ugu st Specifications Industrial Engine. M G D (Engine) MGB (Engine)

K EN R A ugu st Specifications Industrial Engine. M G D (Engine) MGB (Engine) K EN R 623 0-00 A ugu st 200 6 Specifications 2506-15 Industrial Engine M G A (Engine) MGB (Engine) M G D (Engine) Important Safety Information i01658146 Most accidents that involve product operation,

More information

10. CRANKCASE/CRANKSHAFT/TRANS- MISSION SYSTEM/STARTER SPINDLE CK

10. CRANKCASE/CRANKSHAFT/TRANS- MISSION SYSTEM/STARTER SPINDLE CK 10 10 10-0 SERVICE INFORMATION... 10-1 STARTER SPINDLE... 10-6 TROUBLESHOOTING... 10-2 CRANKSHAFT... 10-8 CRANKCASE REMOVAL... 10-3 CRANKCASE INSTALLATION... 10-10 TRANSMISSION SYSTEM... 10-3 SERVICE INFORMATION

More information

https://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl...

https://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl... Page 1 of 7 VELOSTER(FS) >2013 > G 1.6 T-GDI > Engine Mechanical System > General Information > Specifications Specifications General Type Description Specifications Except Europe In-line, DOHC Number

More information

Motorcycle - Specifications

Motorcycle - Specifications Motorcycle - Specifications Model Name FZ400R Model Code 46X0 Model Year 1985 Destination JAPAN Section/Item Chassis Maintenance Specification (Chassis) Chassis Frame type Double cradle Caster angle 26.00

More information

ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3-1 ENGINE REMOVAL 3-1 ENGINE REINSTALLATION 3-5 ENGINE DISASSEMBLY 3-7 STARTER MOTER 3-7

ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3-1 ENGINE REMOVAL 3-1 ENGINE REINSTALLATION 3-5 ENGINE DISASSEMBLY 3-7 STARTER MOTER 3-7 ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3-1 ENGINE REMOVAL 3-1 ENGINE REINSTALLATION 3-5 ENGINE DISASSEMBLY 3-7 3 STARTER MOTER 3-7 CYLINDER HEAD COVER 3-8 PISTON 3-12 MAGNETO COVER 3-13 MAGNETO

More information

ENGINE REMOVAL Install: Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2. Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6.

ENGINE REMOVAL Install: Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2. Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6. ENGINE REMOVAL 4. Install: Gasket New Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2 Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6. Install: Clamp Slide the clamp onto the end of the muffler and insert

More information

service bulletin MCM 454 Magnum EFI, MIE 454 EFI Ski GM Gen V Engine Specifications No Magnum 454 EFI Model EFI Ski (Average Octane Rating)

service bulletin MCM 454 Magnum EFI, MIE 454 EFI Ski GM Gen V Engine Specifications No Magnum 454 EFI Model EFI Ski (Average Octane Rating) service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 93-25 MCM 454 Magnum EFI, MIE 454 EFI Ski GM Gen V Engine Specifications NOTE: Generation V Engines Have the Fuel Pump Mounted on the Belt

More information

Timing Drive Components ( )

Timing Drive Components ( ) Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position

More information

Output Shaft Assembly COMPONENTS

Output Shaft Assembly COMPONENTS MT140 Component Parts (Output Shaft Assembly Output Shaft Assembly COMPONENTS DISASSEMBLY OF OUTPUT SHAFT ASSEMBLY 1. REMOVE SLEEVE FROM OUTPUT SHAFT Using SST, remove the sleeve from the output shaft.

More information

Check The Engine Valve Timing AR05.10 P 6858V

Check The Engine Valve Timing AR05.10 P 6858V 2003 Mercedes Benz C240 2.6L Eng 4Matic Check The Engine Valve AR05.10 P 6858V ENGINE 112 ENGINE 113.962 in MODEL 463.206 /240 /241 /247 /248 /249 /254 ENGINE 113.982 in MODEL 463.243/246 ENGINE 113 (except

More information

SERVICE DATA Date: August 1, 2007

SERVICE DATA Date: August 1, 2007 SERVICE DATA Date: August 1, 2007 Model: LT-A450XK8 VALVE + VALVE GUIDE Valve diam. 30.6 IN. (1.20) EX. 27.0 (1.06) Tappet clearance (when cold) 0.05 0.10 IN. (0.002 0.004) EX. 0.17 0.22 (0.007 0.009)

More information

Appendix D Outline Dimensions

Appendix D Outline Dimensions Appendix D Outline Dimensions Model D81 Bare with Flywheel Suction valve unloaders (optional) 5-1/2" (13.) 5-1/2" (13.) 1/4" NPT drain Inlet 2" Weld flange Inlet pressure guage Outlet pressure gauge Outlet

More information

OVERHAUL. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.

OVERHAUL. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. OVERHAUL COMPONENTS: See page 3232 Overhaul the RH side by the same procedures with LH side. Two types of brake pad exist; one is with slit and the other without slit. 1. REMOVE REAR WHEEL 2. DRAIN FLUID

More information

Double-row ball bearings

Double-row ball bearings Double-row ball bearings Radial double-row ball bearings 262 Definition and capabilities 262 Series 262 Tolerances and clearances 262 Design criteria 263 Suffixes 263 Characteristics 264 Radial double-row

More information

Valve + Valve Guide Unit: mm (in) Item Standard Limit Valve diam. IN (1.20) EX (1.06) Valve clearance (when cold)

Valve + Valve Guide Unit: mm (in) Item Standard Limit Valve diam. IN (1.20) EX (1.06) Valve clearance (when cold) Model: LT-A400FL9 P-17, 24, 28,03 Date: Feb. 12, 2018 SERVICE DATA Valve + Valve Guide Valve diam. IN. 30.6 (1.20) EX. 27.0 (1.06) Valve clearance (when cold) IN. 0.05 0.10 (0.002 0.004) EX. 0.22 0.27

More information

Pistons and connecting rods, disassembling and assembling

Pistons and connecting rods, disassembling and assembling Page 1 of 9 13-53 Pistons and connecting rods, disassembling and assembling 1 - Nut for connecting rod bolt 30 Nm (22 ft lb) + additional 1/4 turn (90 ) Always replace connecting rod bolt -13- Grease thread

More information

SECTION A Engine 3.7L

SECTION A Engine 3.7L 303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone

More information

THE WOLSELEY "VIPER" AERO ENGINE. (Hispano-Suiza W.4.A*)

THE WOLSELEY VIPER AERO ENGINE. (Hispano-Suiza W.4.A*) 13 THE WOLSELEY "VIPER" AERO ENGINE. (Hispano-Suiza W.4.A*) General description. The engine referred to in this article is the Hispano-Suiza 180 hp W.4.A* Aero Engine, as made by Wolseley Motors Ltd. The

More information

INTRODUCTION: Rotary pumps are positive displacement pumps. The rate of flow (discharge) of rotary pump remains constant irrespective of the

INTRODUCTION: Rotary pumps are positive displacement pumps. The rate of flow (discharge) of rotary pump remains constant irrespective of the INTRODUCTION: Rotary pumps are positive displacement pumps. The rate of flow (discharge) of rotary pump remains constant irrespective of the pressure. That is, even at very high pressure, these pumps can

More information

service bulletin MCM 350 Magnum Alpha, MCM 5.7L Bravo, MIE 350 Magnum Tournament Ski Inboard Specifications No. 91-8

service bulletin MCM 350 Magnum Alpha, MCM 5.7L Bravo, MIE 350 Magnum Tournament Ski Inboard Specifications No. 91-8 service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-8 MCM 350 Magnum Alpha, MCM 5.7L Bravo, MIE 350 Magnum Tournament Ski Inboard Specifications NOTE: These three engines have a steel camshaft

More information

Needle Roller Bearings

Needle Roller Bearings Needle Roller Bearings INTERPRECISE Donath GmbH Ostring 2 90587 Obermichelbach Germany Phone +49-911-76630-0 Fax +49-911-76630-30 info@interprecise.de www.idc-bearings.com Needle roller bearings with flanges

More information

service bulletin MCM 4.3L, 4.3LX Alpha GM Generation II Engine Specifications No

service bulletin MCM 4.3L, 4.3LX Alpha GM Generation II Engine Specifications No service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-17 MCM 4.3L, 4.3LX Alpha GM Generation II Engine Specifications NOTE: These engines have an electric fuel pump because there is no pad

More information

General Specifications

General Specifications General Specifications Engine Data Description Litres Engine management EEC V/SFI Emission standard 96 EEC Engine code NSD Firing order 1-3 - 4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cm 3 1998 Compression

More information

ENGINE CONTENTS CAUTION

ENGINE CONTENTS CAUTION ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3- ENGINE REMOVAL 3- ENGINE REINSTALLATION 3-7 ENGINE DISASSEMBLY 3-9 STARTER MOTER 3-9 THERMOSTAT 3-9 ND AIR VALVE 3-0 CYLINDER HEAD COVER 3-0 PISTON

More information

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza 1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST

More information

SERVICE DATA ITEM STD/SPEC. LIMIT. ( in) 1st & 2nd R Approx. 8.2 mm (0.32 in)

SERVICE DATA ITEM STD/SPEC. LIMIT. ( in) 1st & 2nd R Approx. 8.2 mm (0.32 in) 2 STROKE CYLINDER + PISTON + PISTON RING CONROD + CRANKSHAFT CLUTCH SERVICE DATA Piston to cylinder clearance 0.045 0.055 mm (0.0018 0.0022 in) 0.120 mm (0.0047 in) Cylinder bore Piston diam. Cylinder

More information

1950 Pacemaker. Specifications & Adjustments

1950 Pacemaker. Specifications & Adjustments Specifications & Adjustments Specifications & Adjustments ENGINE: Valve Arrangement Bore and Stroke Piston Displacement Maximum Torque Horsepower Actual Taxable Compression Ratio: Cast Iron Head (Std.)

More information

Appendix B Specifications for Vertical Single-Acting Models

Appendix B Specifications for Vertical Single-Acting Models Appendix B Specifications for Vertical Single-Acting Models 9 69 Equipment Type and Options Single-acting, vertical, reciprocating piston type vapor compressor Single packed rod NPT or Class 300 RF connections

More information

DRAIN BRAKE FLUID NOTICE:

DRAIN BRAKE FLUID NOTICE: REAR DISC OVERHAUL Overhaul the RH side by the same procedure as the LH side. 1. REMOVE REAR WHEEL 2. DRAIN FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface.

More information

Measuring a Main Bearing-Cap Bolt. Main Bearing Bolt Maximum Reuse Length

Measuring a Main Bearing-Cap Bolt. Main Bearing Bolt Maximum Reuse Length MBE 900 SERVICE MANUAL 10. Measure the shaft length of the main bearing-cap bolts. Replace any bolts that exceed the maximum shaft length. See Figure 1-34 and see Table 1-13a. 1. Main Bearing-Cap Bolt

More information

TIGHTENING TORQUE CHART For other nuts and bolts not listed in the preceding page, refer to this chart:

TIGHTENING TORQUE CHART For other nuts and bolts not listed in the preceding page, refer to this chart: TIGHTENING TORQUE ENGINE ITEM N m kgfm lbft Cylinder head cover bolt 14 1.4 10.0 Spark plug 11 1.1 8.0 Cylinder head bolt (M10) 47 4.7 18.0 (M6) 10 1.0 7.0 Cylinder bolt 10 1.0 7.0 Camshaft journal holder

More information

D9 & D9G Crawler S/n 66A1 to 66A3265

D9 & D9G Crawler S/n 66A1 to 66A3265 Caterpillar Service Manual D9 & D9G Crawler S/n 66A to 66A65 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR AND IT S

More information

A 1 SERVICE SPECIFICATIONS

A 1 SERVICE SPECIFICATIONS A1 A2 Clutch CLUTCH Specifications Pedal height (from asphalt sheet) Release point (from pedal stroke end position) Push rod play at pedal top Pedal freeplay Disc rivet head depth Disc runout Diaphragm

More information

General Specifications

General Specifications General Specifications Engine Data General Engine management EEC V/SEFI Emission standard 96 EEC Engine code N3A Firing order 1-3-4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cc 1998 Compression ratio

More information

SECTION D Engine 6.0L Diesel

SECTION D Engine 6.0L Diesel 303-01D-i Engine 6.0L Diesel 303-01D-i SECTION 303-01D Engine 6.0L Diesel CONTENTS PAGE DESCRIPTION AND OPERATION Engine... 303-01D-2 303-01D-2 Engine 6.0L Diesel 303-01D-2 DESCRIPTION AND OPERATION Engine

More information

AJV8 Engine Assembly. AJV8 Engine Assembly

AJV8 Engine Assembly. AJV8 Engine Assembly AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart

More information

ENGINE MECHANICAL EM SECTION CONTENTS

ENGINE MECHANICAL EM SECTION CONTENTS ENGINE MECHANICAL EM SECTION CONTENTS INTAKE MANIFOLD...EM-2 Component Parts Location...EM-2 Removal and Installation...EM-3 Inspection...EM-3 EXHAUST MANIFOLD...EM-4 Component Parts Location...EM-4 Removal

More information

SERVICE DATA Date: July 27, 2001 Model: RM250K2

SERVICE DATA Date: July 27, 2001 Model: RM250K2 2 STROKE CYLINDER + PISTON + PISTON RING Piston to cylinder clearance 0.050 0.060 mm 0.120 mm (0.0020 0.0024 in) (0.0047 in) Cylinder bore 66.400 66.415 mm (2.6142 2.6148 in) Nicks or Measure 20 mm (0.79

More information

MODEL NUMBER AND IDENTIFICATION. Pag. 5 CHARACTERISTICS CHARACTERISTIC POWER, TORQUE AND SPECIFIC CONSUMPTION CURVES

MODEL NUMBER AND IDENTIFICATION. Pag. 5 CHARACTERISTICS CHARACTERISTIC POWER, TORQUE AND SPECIFIC CONSUMPTION CURVES MODEL NUMBER AND IDENTIFICATION CHARACTERISTICS CHARACTERISTIC POWER, TORQUE AND SPECIFIC CONSUMPTION CURVES MAINTENANCE - RECOMMENDED OIL TYPE - REFILLING POSSIBLE CAUSES AND TROUBLE SHOOTING OVERALL

More information

3. BEARING ARRANGEMENT DESIGN

3. BEARING ARRANGEMENT DESIGN 3. BEARING ARRANGEMENT DESIGN 3.1 GENERAL PRINCIPLES OF ROLLING BEARING ARRANGEMENT DESIGN Rotating shaft or another component arranged in rolling bearings is guided by them in radial as well as in axial

More information

Transmission/Crankshaft/Crank Case

Transmission/Crankshaft/Crank Case R.Crank Case Crankshaft L.Crank Case 11-0 11. Transmission/Crankshaft/Crank Case Transmission/Crankshaft/Crank Case Service Information 11-1 Troubleshooting 11-2 Transmission 11-3 Crank Case Disassembly

More information

SERVICE MANUAL SUPPLEMENT

SERVICE MANUAL SUPPLEMENT 21-63H-01 PB-770H, PB-770T 1 SERVICE MANUAL SUPPLEMENT 2 ECHO: PB-770H ECHO: PB-770T INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment

More information

NEF SERIES N60. Industrial application N60 ENT

NEF SERIES N60. Industrial application N60 ENT NEF SERIES Industrial application N60 N60 ENT This publication describes the characteristics, data and correct methods for repair operations on each component of the vehicle. If the instructions provided

More information

SCHEDULED MAINTENANCE INTERVALS (GM Y BODY CHEVROLET CORVETTE)

SCHEDULED MAINTENANCE INTERVALS (GM Y BODY CHEVROLET CORVETTE) SCHEDULED MINTENNCE INTERVLS (M Y ODY CHEVROLET CORVETTE) TO E SERVICED TYPE OF SERVICE VEHICLE MILEE INTERVL (x1000) 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 82.5 90 97.5 oil & filter R rake hoses & brake

More information

Advantages and Disadvantages of Rolling Contact Bearings Over Sliding Contact Bearings

Advantages and Disadvantages of Rolling Contact Bearings Over Sliding Contact Bearings Advantages and Disadvantages of Rolling Contact Bearings Over Sliding Contact Bearings Advantages 1. Low starting and running friction except at very high speeds. 2. Ability to withstand momentary shock

More information

lbs sq. Camshaft bush ID 0.5 ± Clearance bush to camshaft ±

lbs sq. Camshaft bush ID 0.5 ± Clearance bush to camshaft ± GENERAL Cubic capacity 347 C.C. Stroke 93 mm. / 3.6614 Cylinder bore Compression ratio Max compression at kick starter speed 2 23 /32 = 2.7187 ± 0.0005 (Re-bore to + 0.02 when wear exceeds 0.008 ). Note:

More information

Camshaft. vw-wi://rl/v.en-us.k wi:: xml?xsl=3. Special tools and workshop equipment required

Camshaft. vw-wi://rl/v.en-us.k wi:: xml?xsl=3. Special tools and workshop equipment required Page 1 of 9 Camshaft Special tools and workshop equipment required Diesel Injection Pump Locking Pin -3359- Counterhold - Camshaft Gear -T10051- Puller - Camshaft Sprocket -T10052- Camshaft Fitting Tool

More information

Page 1 of 9 303-01C Engine 6.0L Diesel 2004 F-Super Duty 250-550/Excursion DESCRIPTION AND OPERATION Procedure revision date: 08/06/2003 Engine Printable View Engine Description The 6.0L diesel engine

More information

Service and Repair CAMSHAFT

Service and Repair CAMSHAFT Service and Repair CAMSHAFT Removal and Installation REMOVAL 1. Remove front timing chain case, camshaft sprocket, timing chain and rear timing chain case. Refer to "REMOVAL". 2. Remove camshaft position

More information

WSS- M97B51-A1 WSS- M2C930-A. 5.7L (6 qt) with filter WSE- M4G323-A4

WSS- M97B51-A1 WSS- M2C930-A. 5.7L (6 qt) with filter WSE- M4G323-A4 SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual SPECIFICATIONS Procedure revision date: 01/22/2009 Material Item Specification Fill Capacity Gasket Maker TA-16 WSK- M2G348-A5 Motorcraft

More information

System description for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines

System description for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines Valve seat lubrication Cylinder lubrication Version 04 Page 2 for cylinder lubrication and valve seat lubrication on

More information

Select 0 position and secure special tool with clamping screw on socket (special tool ).

Select 0 position and secure special tool with clamping screw on socket (special tool ). Tightening torque 11 23 2AZ. Refer to ENGINE - TIGHTENING TORQUES. Installation: Fit special tool 11 3 460 on special tool 11 9 451. Fig. 184: Fitting Special Tool (11 3 460) On Central Bolt NOTE: Special

More information

CHARACTERISTICS CHARACTERISTICS CURVES INTRODUCTION MAIN TORQUE SPECIFICATIONS MAINTENANCE-RECOMM ENDED OIL TYPE-REFILLING

CHARACTERISTICS CHARACTERISTICS CURVES INTRODUCTION MAIN TORQUE SPECIFICATIONS MAINTENANCE-RECOMM ENDED OIL TYPE-REFILLING CHARACTERISTICS CHARACTERISTICS CURVES INTRODUCTION MAIN TORQUE SPECIFICATIONS MAINTENANCE-RECOMM ENDED OIL TYPE-REFILLING MODEL NUMBER AND ENGINE IDENTIFICATION OVERALL DIMENSIONS 8LD600-2; 8LD665-2;

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 41135 OVERHAUL 4108901 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 0.40 mm (0.0039 0.0157 in.) C68252 2. INSPECT 2ND GEAR THRUST CLEARANCE

More information

D6 & D6C Crawlers S/n 74A1, 76A1, 41A1, 71A1, 73A1, 82A1 & 96A1 & up

D6 & D6C Crawlers S/n 74A1, 76A1, 41A1, 71A1, 73A1, 82A1 & 96A1 & up Caterpillar Service Manual D6 & D6C Crawlers S/n 74A, 76A, 4A, 7A, 73A, 82A & 96A & up Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS.

More information

TECHNICAL DATA - ENGINE 250/300/380 SX/MXC/EXC/EGS 98 (all models out of USA)

TECHNICAL DATA - ENGINE 250/300/380 SX/MXC/EXC/EGS 98 (all models out of USA) TECHNICAL DATA - ENGINE 250/300/380 SX/MXC/EXC/EGS 98 (all models out of USA) Engine 250 SX 250 EXC, EGS 300 EXC, EGS 380 SX 380 EXC, EGS Design Liquid-cooled single-cylinder two-stroke engine with Twin

More information

ENGINE MECHANICAL SECTION EM CONTENTS EM-1 IDX MODIFICATION NOTICE:

ENGINE MECHANICAL SECTION EM CONTENTS EM-1 IDX MODIFICATION NOTICE: ENNE MNICAL STION EM MODIFICION NOTICE: TB45E engine models with three way catalyst have been provided for the Middle East and General areas. Turbocharger for engine has been changed. For information not

More information

Motorcycle 2012 Model: RM-Z450 Date: August 2011

Motorcycle 2012 Model: RM-Z450 Date: August 2011 RM-Z450L2 Motorcycle 2012 Model: RM-Z450 Date: August 2011 New Feature New graphics Key Features 1. 449cm3 4-stroke liquid-cooled DOHC 4-valve fuel-injected engine developed and refined to deliver phenomenal

More information

1989 BMW 635CSi. 3.5L 6-CYL Engine - 3.5L 6-Cylinder

1989 BMW 635CSi. 3.5L 6-CYL Engine - 3.5L 6-Cylinder Fig. 3: Rocker Arm Assembly Courtesy of BMW OF NORTH AMERICA, INC. VALVE SPRINGS NOTE: Install springs with paint stripe (tight coil end) against head. Inspection Check spring free length. Check spring

More information