INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Alannah Foster
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDA ACCORD HYBRID AII Issue Date JULY 2006 NOTE: The outside temperature gauge cannot be installed in a vehicle with fog lights Fog light harness PARTS LIST Right fog light Switch harness Left fog light Right bracket Fog light switch Relay (black) Left bracket Fuse label Right trim 4 Self-tapping screws, 5 x 16 mm Left trim 2 Washer-screws, 5 x 16 mm 4 Step screws, 4 mm 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 08V31-SDA of 19

2 2 Ground bolts Washer 2 Washer-bolts, 6 x 16 mm TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver Small flat-tip screwdriver 10 mm Combination wrench 10 mm Socket Ratchet Measure Eye protection (face shield, safety goggles, etc.) File Utility knife 2 Washer-screws, 4 x 8 mm 24 wire ties Illustration of the Fog Lights Installed on the Vehicle 4 Short wire ties RELAY Relay bracket 2 Screw locks RIGHT FOG LIGHT LEFT 4 Spring nuts Y Fuse (20A) Flange nut INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your car. These procedures should not be attempted by do-it-yourselfers. Corrugate tube 2 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

3 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Open the hood. Disconnect the negative cable from the battery. 3. Remove the radiator cover (ten clips and four retaining tabs). 5. Remove the air duct cover (two clips and pull it out toward you). CLIPS (2) AIR DUCT COVER CLIPS (10) TABS (4) RADIATOR COVER AIR DUCT T 6. Remove the lid from the front bumper (five retaining tabs). 4. Remove the hood latch cover (one clip). BUMPER CLIP HOOD LATCH COVER TABS (5) LID (DISCARD) Y P 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 3 of 19

4 7. Route the fog light harness 2-pin connector through the front bulkhead and alongside the vehicle harness. 2-PIN 9. Remove and discard the lower bolt that secures the hood latch bracket. Using one ground bolt and the washer supplied, attach the fog light harness ground terminal to the hood latch bracket. 10. On left side of vehicle, secure the fog light harness to the vehicle harness with the five wire ties in the areas shown. Push the fog light harness clip into the hole in the body panel. HOLE P 8. Route the 2-pin connector end of the fog light harness to the front bulkhead alongside the vehicle harness. GROUND TERMINAL WASHER BOLT (Discard.) HOOD LATCH BRACKET GROUND BOLT P 11. On the right side of vehicle, secure the green tape part of the fog light harness to the vehicle harness with four wire ties. WIRE TIE CLIP S WIRE TIE GREEN TAPE P ( Do not allow the harness to contact the air conditioner pipe.) P 4 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

5 12. Remove the sub fuse box (one retaining tab). BRACKET SUB FUSE BOX 15. Remove the vehicle wire tie from the bracket (one retaining tab). TAB BRACKET TAB TAB 3-PIN Y BRACKET 13. Remove the vehicle 3-pin connector (one retaining tab) Y 14. Remove the bracket from the under-hood fuse/ relay box (one retaining tab). 16. Remove the under-hood fuse/relay box cover (four retaining tabs). BRACKET COVER TABS (4) TAB Y Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 5 of 19

6 17. Remove the two vehicle harnesses (two bolts). 19. Remove the two bolts that fasten the under-hood fuse/relay box. BOLTS (2) BOLTS (2) BOLT 18. Remove the sub fuse box (one retaining tab) Y AIR CLEANER HOUSING COVER BOLT (Remove.) SUB FUSE BOX 20. Remove the one bolt that fastens the air cleaner housing cover. 21. Release the six retaining tabs and remove the under-hood fuse/relay box under cover. TABS (6) TAB Y UNDER COVER Y 6 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

7 22. Raise the under-hood fuse/relay box. (Raise.) 24. Unplug the vehicle 14-pin and 20-pin connectors from the under-hood fuse/relay box. Release the retainer on the vehicle 14-pin connector, and insert the fog light harness blue wire terminal into the vehicle 14-pin connector. Reattach the retainer on the 14-pin connector. 14-PIN FUSE/RELAY BOX UNDER COVER Y 23. Lift the air cleaner housing cover up, and route the other end of the fog light harness toward the engine alongside the vehicle harness. 14-PIN 20-PIN As viewed from back side RETAINER BLUE/RED TERMINAL 20-PIN BLUE TERMINAL RETAINER Lift Harness side view Harness side view FUSE/RELAY BOX 14-PIN AIR CLEANER HOUSING COVER P 20-PIN TERMINALS (2) P 25. Release the retainer on the vehicle 20-pin connector, and insert the fog light harness blue/ red wire terminal to the vehicle 20-pin connector. Reattach the retainer on the 20-pin connector. 26. Plug the vehicle 14-pin and 20-pin connectors into the under-hood fuse/relay box American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 7 of 19

8 27. Secure the fog light harness to the vehicle harness with one short wire tie in the area shown. FUSE/RELAY BOX SHORT 31. Under the under-hood fuse/relay box, locate the vehicle 3-pin connector blue-taped to the vehicle harness, and remove the blue tape to free the connector. Connect the fog light harness 3-pin connector into the 3-pin connector you just freed. Secure the fog light harness to the vehicle harness with four wire ties in the area shown. UNDER- HOOD FUSE/ RELAY BOX BLUE- TAPE (Remove.) 3-PIN UNDER COVER 28. Reinstall the under-hood fuse/relay box under cover. Be careful not to pinch the wires Y WIRE TIE 29. Wrap the corrugate tube around the vehicle harness and secure with the three short wire ties. 3-PIN Y CORRUGATE TUBE SHORT WIRE TIES (3) Y 30. Reinstall the vehicle wire tie removed in step of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

9 NOTE: If the 3-pin connector is already used by another accessory, locate the 3-pin connector taped to that other accessory harness. Remove the tape and dummy connector from that other accessory harness. Plug the fog light harness 3-pin connector into that other accessory harness. 33. Remove the mounting bolt that secures the vehicle bracket, and attach the relay bracket with this bolt, then plug the fog light harness 4-pin connector into the relay. MOUNTING BOLT (Reuse.) RELAY BRACKET 3-PIN OTHER ACCESSORY 3-PIN 3-PIN FRAME RELAY WIRE TIE OTHER ACCESSORY 3-PIN 4-PIN OF Y 32. Install the relay to the relay bracket with one washer-bolt and one flange nut. RELAY BRACKET T 34. Secure the fog light harness to the vehicle harness with three wire ties in the areas shown. FLANGE NUT WASHER- BOLT RELAY (BLACK) Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 9 of 19

10 35. Remove the under-hood fuse/relay box cover (four retaining tabs). COVER Installing Fog Lights 38. Cut out the front bumper as shown. Cut out. TABS (4) UTILITY KNIFE FUSE (20A) BUMPER Cut out Y FUSE (20A) FUSE/RELAY BOX FUSE/RELAY BOX T 39. Slide two spring nuts onto the front bumper from the inner side. 36. Install the 20A fuse (provided) into the No.10 slot of the under-hood fuse/relay box. 37. Attach the 20A fuse label over the No.10 spot of the under-hood fuse/relay box cover. Reinstall the under-hood fuse/relay box cover. FUSE LABEL (20A) SPRING NUTS (2) BUMPER FUSE/RELAY BOX LID No T Y 10 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

11 40. Install the left fog light bracket on the front bumper with two 5 x 16 mm self-tapping screws. BUMPER 42. Install the 5 x 16 mm washer-screw and screw lock on the left fog light trim as shown. LEFT FOG LIGHT TRIM SCREW LOCK 5 x 16 mm WASHER- SCREW 5 x 16 mm SELF- TAPPING SCREWS (2) LEFT FOG LIGHT BRACKET Y 43. Install the fog light harness clip on the left fog light bracket Y 41. Install the left fog light on the left fog light trim using two 4 mm step screws and one 4 x 8 mm washer-screw. LEFT FOG LIGHT BRACKET CLIP 2-PIN LEFT FOG LIGHT TRIM BUMPER 4 mm STEP SCREW TAB 4 x 8 mm WASHER- SCREW LEFT FOG LIGHT 4 mm STEP SCREW 5 x 16 mm WASHER- SCREW INSTALLED IN STEP 44 LEFT FOG LIGHT Y 44. Connect the fog light harness 2-pin connector to the left fog light Y 45. Align the two retaining tabs on the left fog light with the corresponding positions of the front bumper and install the left fog light on the front bumper using the 5 x 16 mm washer-screw that you installed in step Repeat step 40 through 47 to install the right fog light on the right side the vehicle American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 11 of 19

12 Routing the Switch Harness 47. Remove the driver s dashboard lower cover: 48. If equipped, remove the driver s dashboard under cover (the three clips, one pin and one holder). Remove the one self-tapping screw. Release the four clips on the left side first by pulling out on the driver s dashboard lower cover. After releasing the four clips, insert the flat-tip screwdriver between the clip and the dashboard frame. Gently twist the screwdriver to release the clip. HOLDER Release the two clips on the right side last. Unplug the vehicle connector, and remove the lower cover. CLIP (Release these clips first.) DRIVER S DASHBOARD UNDER COVER PIN CLIPS (3) T CLIP (Release these clips last.) 49. Plug the switch harness 6-pin connector into the 6-pin connector connection position of the underdash fuse/relay box. 6-PIN CLIPS (7) DRIVER S DASHBOARD LOWER COVER SELF- TAPPING SCREW FLAT-TIP SCREWDRIVER FRAME CLIP (Release the clip by inserting the flattip screwdriver between the clip and the dashboard frame, and twist the screwdriver to release the clip.) K Front view 6-PIN CONNECTION POSITION UNDER-DASH FUSE/RELAY BOX Y 12 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

13 NOTE: If the fuse box 6-pin connector is already being used by another accessory, unplug the 6- pin connector from the under-dash fuse/relay box. Locate the 6-pin connector taped to the switch harness. Remove the dummy connector from switch harness. Plug the other accessory harness 6-pin into switch harness, and plug the switch harness 6-pin connector into the under-dash fuse/ relay box. 51. Behind the steering hanger pipe, locate the 2-pin connector blue-taped to the vehicle harness. Connect the switch harness 2-pin connector to the vehicle 2-pin connector. 2-PIN STEERING HANGER PIPE 6-PIN DUMMY OTHER ACCESSORY 6-PIN 2-PIN UNDER-DASH T 50. Route the switch harness 5-pin connector (blue) to the body panel opening alongside the vehicle harness. Secure the switch harness to the vehicle harness with one wire tie in the area shown Y NOTE: If the 2-pin connector is already being used by another accessory, locate the 2-pin connector taped to that other accessory harness. Plug the switch harness 2-pin connector into the other accessory harness. BODY PANEL OPENING 2-PIN OF OTHER ACCESSORY 2-PIN 5-PIN (Blue) 2-PIN Y Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 13 of 19

14 52. On the left of the steering shaft, locate the 3-pin connector black-taped to the vehicle harness, and plug the switch harness 3-pin connector in the 3-pin connector. 53. Secure the switch harness to the vehicle harness with six wire ties in the areas shown. 3-PIN STEERING SHAFT 3-PIN T NOTE: If the 3-pin connector is already being used by another accessory, locate the 3-pin connector taped to that other accessory harness. Remove the dummy connector from that other accessory harness. Plug the switch harness 3-pin connector into the other accessory harness. 54. Remove the switch lid from the driver s side dashboard lower cover, and install the fog light switch in the driver s dashboard lower cover. HOLE T 3-PIN LID DRIVER S DASHBOARD LOWER COVER T DUMMY OTHER ACCESSORY 3-PIN T 14 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

15 55. If equipped, reinstall the driver s dashboard under cover. HOLDER 57. Check that all wire harnesses are routed properly and all connectors are plugged in. 58. Reinstall all removed parts. Check that all clips and fasteners are installed securely. 59. Reconnect the negative cable to the battery. USE AND CARE How to Operate Fog Lights Turn the light switch to the on position (headlights on low beam ). Press the fog light switch (indicator is on). The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Fog Light Aiming Adjustment CLIPS (3) DRIVER S DASHBOARD UNDER COVER 56. Plug the switch harness 5-pin connector (blue) into the fog light switch, and plug the two vehicle connectors then reinstall the dashboard lower cover. 5-PIN OF (BLUE) PIN T 60. Adjust the fog light: Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment screw in or out until the correct aiming is obtained. To raise To lower PHILLlPS SCREWDRIVER AIMING ADJUSTMENT GEAR PHILLlPS SCREWDRIVER Y DRIVER S DASHBOARD LOWER COVER T 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 15 of 19

16 61. Reset the clock, and reset the radio station presets. 62. Do the ECU idle learn procedure. Make sure all electrical items are turned off. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on. Let the engine idle for about 5 minutes with the throttle fully closed and with all electrical items off. NOTE: If the radiator fan comes on during this step, the time when it is operating must not be included in the 5 minutes. NOTE: When The Battery Terminals Are Disconnected: Remaining Capacity of the IMA Battery is not indicated when the engine is started. It will be indicated after driving for about 30 minutes. At that time, regeneration will be lowered temporarily, but this is normal. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 63. Start the engine. Push down on the driver s window switch until the window is fully open. 64. Pull up on the driver s window switch fully to close the window completely, then hold the switch for 2 seconds or more. 65. Test the driver s window AUTO function. BULB REPLACEMENT 1. Loosen the screw through the hole of the left fog light trim and pull the left fog light garnish toward you. 2. Disconnect the fog light harness 2-pin connector and remove the left fog light from the front bumper. SCREW BUMPER 3. Remove the bulb. LEFT FOG LIGHT Y BULB Y 16 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

17 4. Install the new bulb into the socket. Use only a genuine Honda halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. SOCKET NEW BULB Y 5. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the self-tapping screw and bolts securely. 6. Check the operation of the fog light; adjust the aiming if necessary American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 17 of 19

18 CIRCUIT DIAGRAM HOT WITH HEADLIGHT IN HAED,AND DIMMER IN HIGHT Under-hood Relay UNDER-DASH Box FUSE/RELAY BOX HOT IN COMBINATION LIGHT OR FR RED/BLK WHT/GRN HOT WITH HEADLIGHT IN HAED FUSE/RELAY Fog BOX Light Fuse BATTERY HOT AT ALL 20 A 20A TIMES RELAY MODULE FOG LIGHT CONTROL CIRCUIT LEFT RED/GRN BLU/RED BLU/RED BLU/YEL RELAY RIGHT HOT WITH HEADLIGHT IN PARK OR HEAD GRN RED/BLK 2 RED Illumination Control BLU BLU 1 2 GRN RED Relay DASH LIGHT 1 BRIGHTNESS CONTROLLER BLK Relay 1:INDICATOR 2:ILLUMINATION Switch 1=Indicato 2=Switch Illumination BLU/YEL BLK Front Fog Light BLK BLK BLK BLK P OFF BLK BLACK BRN BROWN YEL YELLOW ORN ORANGE BLU BLUE PUR PURPLE LIGHT GRN GREEN NAT NATURAL OFF Low Hi RED RED PNK PINK WHT WHITE GRY GRAY OFF ON ON - LT BLU LIGHT BLUE LT GRN LIGHT GREEN 18 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDA-102 2007 ACCORD 4-DOOR AII 32672 Issue Date JULY 2006 NOTE: Fog lights can be installed in a vehicle equipped with a factory