Operating Manual. Operating Manual HYBRIDIZATION INCUBATOR. combi-h12 combi-d24 combi-v12 combi-sv12 combi-sv120

Transcription

1 Operating Manual Operating Manual. PRODUCTS DESCRIPTION. USER CONSIDERATION. USER OPERATION. ACCESSORIES. MAINTENANCE AND CLEANING. FAULTY RUNNING. WARRANTY combi-h combi-d combi-v combi-sv combi-sv0 YANG-CHUN P.O BOX 00, SEOUL, KOREA TEL: ---/ FAX:---0

2 Introduction Variable accessories available (Rotor, Rocking platform - optional) Use a magnetic seal for closing door. As going time, the door would be close more strongly. Interior electrical outlet for powering small equipments Use air layer for protecting inside heat in order to clean environment and persist the temperature with stable. kind of safe device. A. Electrical fuse B. If current temp. does not reach the setting temp. for hours ALM Lamp on temperature controller would be blinked. C. This oven is used in up to 0. if the current temp. is over 0., ALM lamp would be blinked. D. If the current temp. Is over, the heater would be turned out. E. If all the safe device of temperature does not work, all function of this ovens should be stopped at 0 PRODUCT DESCRIPTION Hybridization incubators PID temperature control Rotating movement combi-h (Dimension - external : WXDXH, Internal : W X D0 X H) combi-d Rocker + Rotating Dual (Dimension - external : W0XD0XH0, Internal : W X D0 X H) combi-v Rocker + Rotating (Dimension - external : WXDXH, Internal : W X D0 X H) Rotating + shaking movement combi-sv Rocker + Rotating Rocker + Shaking + Rotating (Dimension - external : WXDXH, Internal : W X D0 X H) Combi-sv0 Rocker + Shaking + Rotating + Tachometer (Dimension - external : W0XD0XH0, Internal : W X D X H)

3 Difference of incubators HORIZONTAL TYPE combi-h combi-d * digital control temperature. * rotor speed control. * optional rocking platform for washing. (outside cabinet : W0XD0XHmm) (inside chamber : WXD0XHmm) * digital control temperature. * rotor speed control. * optional rocking platform for washing. (outside cabinet : W0XD0XH0mm) (inside chamber : WXD0XHmm) Dual-type standard size. Hybridization incubator. RK-H (rocking platform) can be settle inside. RT- (accessories) series is for combi-h. standard size. Hybridization incubator. RK-H (rocking platform) can be settle inside. RT- (accessories) series is for combi-d. PRODUCT DESCRIPTION VERTICAL TYPE combi-v * digital control temperature. * rotor speed control. * optional rocking platform for washing. (outside cabinet : WXDXHmm) (inside chamber : WXD0XHmm) standard size. Hybridization incubator. RK-V (rocking platform) can be settle inside. RT- (accessories) series is for combi-v. combi-sv * digital control temperature. * rotor speed control. * optional rocking platform for washing. (outside cabinet : WXDXHmm) (inside chamber : WXD0XHmm) standard size. Hybridization incubator. RK- (rocking platform) can be settle inside. RT- (accessories) series is for combi-. Combi-sv0 * digital control temperature. * digital display speed. (tachometer) * rotor speed control & available select. * optional rocking platform for washing. (outside cabinet : W0XD0XH0mm) (inside chamber : WXDXHmm) standard size. Hybridization incubator. RK- (rocking platform) can be settle inside. RT- (accessories) series is for combi-0.

4 Specification Model Temp. Range Temp. Accuracy Temp. Timer Material Weight Dimensions(mm) Wattage Power Rotation Shaker combi-h Overall W x D x H Internal W x D0 x H combi-d combi-v combi- combi-0 Ambient + ~ 0 ±0. hour min 0~0rpm - 0~00rpm Inside chamber : Stainless steel kg kg 0kg kg kg Overall W0 x D0 x H0 Internal W x D0 x H Overall W x D x H Internal W x D0 x H Overall W x D x H Internal W x D0 x H AC00V / 0/0Hz AC0V / 0/0Hz AC0V / 0/0Hz AC0V / 0/0Hz(CE cert) AC0V / 0/0Hz Overall W0 x D0 x H0 Internal W x D x H 00W 00W 00W 00W 00W PRODUCT DESCRIPTION Description BACK SIDE TEMPERATURE CONTROLLER Receptacle MAIN BODY Specification Serial Number Voltage / Hz RUN Lamp(orange) TIME Lamp(green) HEAT Lamp(red) ALARM Lamp(red) Current temperature Setting temperature UP key DOWN key MOVE key MODE key RUN/ key Door Temperature sensor Magnetic sealer Rubber band Temperature controller Glass controller ON/ switch Clutch "U" plastic hub

5 TEMPERATURE C TEMPERATURE C User consideration For place combi-v, the and D horizontally with the ground, the two front screw foots could be used for making a balance. Do not stand the instrument near a wall. On the back panel, There are ventilation holes. The instrument should be left from at least cm. Ventilation hole USER CONSIDERATION 0cm Check if the voltage indicated on appliance corresponds to the local mains voltage before you connect the appliance. Unplug the appliance : - If problems occur during the heating and rotating process. - Before you start cleaning the unit. - Never use the appliance if the plug, the cord or the appliance it self is damaged 0 V 0V 0V Do not place the hybridization incubators beside a sunny place or heater. If the main body is higher than room temperature, It could affects the inside setting temperature. Be careful not to drop any chemical liquid on the instrument to prolong the life of the instrument. For example, PEG could be reason for the paint on the surface to be peeled off. Magnetic seal. Keep the magnetic seal. If it is dust or have some particles, it could be possible the setting temperature is not stable. Environmental conditions - Indoor use. - Environment temperature to 0. - Maximum relative humidity 0% for temperatures up to decreasing linearly to 0% relative humidity at 0. - Mains supply voltage fluctuations not to exceed ±0% of the nominal voltage. - Other supply voltage fluctuations as stated by the manufacturer. - Transient overvoltages according to installation categories.

6 User operation This section summarizes operation procedures for FINEPCR`s hybridization ovens controlling the temperature and the rotate. 0V Check the name rating plate for the correct voltage, then plug the power cord into the receptacle on back of the instrument. Turn the power ON/ control button to position 'ON' USER OPERATION Plug the power cord into the wall receptacle. p A - When switch turn on, p (the type of sensor) is displayed A on and - (software vision)is displayed on for second. 0 Do not open with strong. The hinges of door could be defected. The door could be opened until After second, the current block TEMPERATURE is displayed on and the setting TEMPERATURE is displayed on. (This is normal MODE) "U" plastic hub Open the rotor hook.. Put into the clutch hole.. Push the rotor into the U-boss hole Put the shaft into the hole of clutch with fitting with the shape of the hole. 000 p p 0 In order to set the desired TEMPERATURE, press MODE key for.seconds then p is displayed on and the rightmost FND blink on then stop pressing MODE key. Unless stop pressing MODE key, the setting return to normal MODE At this step, for example to set, when press MOVE Key each TIME, the rightmost FND blink moves into left. Press MOVE key till the rightmost FND blink moves into the second place of right. TEMPERATURE range can be set per 0. Close the rotor hook p 000 When press UP key, the displayed figure increases one by one then press UP key continuously till the displayed figure reaches at.

7 User operation This section summarizes operation procedures for FINEPCR`s hybridization ovens controlling the temperature and the rotate..0 p The figure should be displayed at.0 to use MOVE, UP and DOWN key..0.0 Press MODE key once again after the setting of BEEP sound time then the screen return to the step of no.. Then the setting TEMPERATURE.0 is displayed on. All of TEMPERATURE, TIME and beep sound time setting are finished. You should return to normal MODE. Press MODE key for.seconds and stop pressing MODE key when normal MODE has been returned. USER OPERATION I e I e 0000 Press MODE key once again after the setting of the TEMPERATURE then is displayed on and is displayed on. TIME range can be set to Hours minutes. Two positions of the front are hour and next two positions are Minute. The method of TIME setting is the same as the method of TEMPERATURE setting..0.0 When normal MODE has been returned, press RUN key for.seconds as per the shown picture then RUN lamp is on and TEMPERATURE rises in beginning. Then if the TIME has been set, TIME lamp will be on till to reach the setting TEMPERATURE and the TIME lamp will blink when the TEMPERATURE has reached the setting TEMPERATURE. Then you can know the timer is being operated well. Unless the TIME is sets, TIME lamp is not on. P Eep 0000 Press MODE key once P again after TIME setting then Eep is displayed on and P 0000 is displayed on. Eep sound time can be set to seconds. The method of BEEP sound time setting is the same as the method of TEMPERATURE setting and TIME setting.

8 TEMPERATURE User operation This section summarizes operation procedures for FINEPCR`s hybridization ovens controlling the temperature and the rotate. USER OPERATION.0.0 HEAT lamp let you know that power is supplying the heater normally while the unit is running..0.0 Press RUN key for.seconds at normal mode. The existing setting TEMPERATURE, TIME and BEEP sound time are kept in memory. Therefore, the unit will be operated as the same method before. If you want to change the setting TEMPERATURE, TIME and BEEP sound time, please start to reset all of the setting value from the step of NO If the TIME is set and you want to see the set value while the unit is running, press MOVE key once then will be changed setting TEMPERATURE to TIME. The TIME displayed on the screen is reminder TIME and make it a rule to subtraction. Install the sample bottles into putting the rotor clip by pushing.0 E p After the setting TIME has passed. End is displayed on and the setting BEEP sound beeps for the setting BEEP sound time. Then press stop key BEEP sound will be stopped. Also, all functions will be stopped and will return to normal MODE. Control the rotor speed (0~0rpm)

9 Accessories RT~ standard for using it in other ovens except combi-h and combi-v, combi-, combi-0 RT series ACCESSORIES RT- RT- RT- RT-V RT-V RT-V RT-H RT00 series RT00- RT00- RT00- Other RK-H H-DT shelf HY-Bag BOTTLES BT0-0 (0mm diameter X 0mm length bottle with silicon cap) BT0-00 (0mm diameter X 00mm length bottle with silicon cap) BT0-00 (0mm diameter X 00mm length bottle with silicon cap) BT0-00 (0mm diameter X 00mm length bottle with silicon cap)

10 User operation How to install Rocking platform USER OPERATION Make a right angle the connecting bar with rocking platform Place Drip tray until touching the wall pannel of incubator for ventilation smoothly. Hot air circulation Drip Tray Drip Tray

11 User operation How to install ROTOR USER OPERATION Put into rotor and then put the hook into a gap Put a right side of rotor into a hole 0

12 Maintenance and Cleaning Always unplug the instrument before you start cleaning it. Never immerse the appliance in water. Never use the instrument if the plug, the cord or the instrument itself is damaged. Keep the magnetic sealing clean for insulation. Clean the magnetic sealing, case and door with a damp cloth or with detergent. Magnetic sealing MAINTENANCE AND CLEANING

13 Faulty running. The current and setting temperature is different - Temperature bar may not corrected, After testing the inside temperatures with several temp. bars at the same time, you could calibrate by referring calibrating temperature section of technical specification. FAULTY RUNNING. The rotor speed dose not meet a requirement. - FINEPCR's units could be controlled in Maximum and Minimum speed. Set the speed to the desired speed. (Refer the Max/Min speed control section of technical specification). After turning on the power switch, The LED of the temperature controller could not display current temp. - In this case, the electronic fuse is broken. If you see the back of the incubator, the fuse box could be seen. After detaching the box as the pictures, change the fuse. spare fuse remove used fuse If the equipment have other defects, It should be informed to an authorized servicing agent.

14 Warranty WARRANTY YEAR WARRANTY Limited Warranty : This equipment has been tested all the functions and parts for proper operation before shipment. Please read this manual carefully. If you have any questions or problems, check with your dealer or write us direct. This equipment is warranted for a period of year from date of purchase against defects in workmanship and material only. If a system component should ever fail to work perfectly. It can be repaired or replaced by our after-sales service without difficulty. Model#: Serial# : Date Purchased : Dealer Name : City and Country : YANG-CHUN P.O BOX 00, SEOUL, KOREA TEL: ---/ FAX:---0 finepcr@finepcr.com