Product Name Chair Conversion Kit (to Console Delivery Unit) Installation [Kit # xx]
|
|
- Marshall Anthony
- 5 years ago
- Views:
Transcription
1 Elevance Product Name Chair Conversion Kit (to Console Delivery Installation Unit) Installation [Kit # xx] Attention: Use this kit to convert an Elevance Chair to a Chair with an Elevance Console mounted Delivery Unit. Applies to Models: Special Tools: none Language of origin: English Step 1: Install Anchor Bolt. A) Reference the installation sheet in the Anchor Bolt Installation Kit, x, included with this kit. Note: Do not replace base cover after installing anchor bolt. You will need to access this area again. Seat Upholstery Back Upholstery Pivot Cover Step 2: Position the Chair. A) Tap the Pivot Cover three times to raise the chair. (Chair beeps until it reaches the home position). B) Unplug chair from power source. C) Remove Seat and Back upholstery Midmark Corp. 60 Vista Drive Versailles, OH USA Rev. B (4/17/16)
2 Step 3: Remove Lift Arm and Pivot Covers: A) Remove Upper and Lower Lift Arm Covers B) Remove Upper Pivot Cover (loosen two screws). C) Remove Lower Pivot Cover (pull cover over mount screws). D) Remove Pivot Switch Bracket (two mount screws on top and two on bottom). Upper Lift Arm Cover Covers Removal Video Pivot Switch Bracket Lower Lift Arm Cover Upper Pivot Cover Lower Pivot Cover 2
3 Step 4: Remove Covers: A) Remove Left and Right Seat Shrouds (three screws each). B) Remove Left and Right Frame Covers (two screws each). C) Remove Frame Top Cover (two screws). D) Remove Seat Frame. E) Remove Front Cover. Frame Top Cover Seat Frame Right Shroud Left Frame Cover Earlier Models Seat Frame Mountings Front Cover 3
4 warning Use caution when operating equipment with covers removed. Step 5: Re-position Chair to access Rotation Stop holes. A) Plug chair into power source. B) Lower Back to Full Down position. C) Unplug chair from power source. Step 6: Unhook springs and remove carriage axles. A) Rotate the Toe Lift Rail towards the back of the chair. B) Unhook both Springs (from foot end of chair). C) Remove Carriage Clamp Bolt, Carriage Clamp and Thrust Washer.. D) Remove two Back Axles, pulling them out from each side of chair. E) Remove Cylinder Carriage Axle, pulling it out from left side of chair. F) Rotate back (not shown) as necessary for you to access the rotation stop holes in the chair casting. G) Install two Rotation Stop bolts into the Chair casting. H) Repeat steps 6D) and 6E) in reverse to install the Axles. I) Install Washers, Carriage Clamp and Bolt tightened to specified space* * Use a 7/32 Allen wrench to set the space between the Carriage Clamp Bolt and chair casting as you tighten the bolt Clamp bolt Carriage Clamp Back Axle Thrust Washer 7/32" Allen Wrench Rotation Stop Bolt Spring Toe Lift Rail Back Axle Cylinder Carriage Axle See next page for Alternate Step 6 for earlier chair models. 4
5 Alternate Step 6: for Earlier Chair Models Reference illustration on previous page. A) Rotate the Toe Lift Rail towards the back of the chair. B) Unhook both Springs (from foot end of chair). C) Remove Carriage Clamp Bolt, Carriage Clamp and Thrust Washer.. D) Remove two Back Axles, pulling them out from each side of chair. E) Remove Cylinder Carriage Axle, pulling it out from left side of chair. F) Rotate back (not shown) as necessary for you to access the rotation stop holes in the chair casting. G) Install two Rotation Stop bolts into the Chair casting. H) Repeat steps 6D) and 6E) in reverse to install the Axles. I) Install Washers, Carriage Clamp and Bolt tightened to specified space* * Use a 3/8 Allen wrench to set the space as you tighten Carriage Clamp Bolt, THEN, back bolt off one turn Clamp bolt Carriage Clamp 3/8" Allen Wrench Thrust Washers 5
6 warning Use caution when operating equipment with covers removed. Step 7: Re-position Chair Before Continuing. A) Plug chair into power source. B) Position the back to provide easiest access to the pivot hole. C) Unplug chair from power source. D) Remove Strap Clamp (two screws) and position guide band out of the way. E) Remove Umbilical Cover Bracket. F) Remove Rotation Hub Bracket. Umbilical Cover Bracket Rotation Hub Bracket Pivot Hole Strap Clamp / Guide Band Console Mounting Arm Step 8: Install the Console Mounting Arm. A) Reference the Installation Instructions included with the Console Mounting Arm. 6
7 Step 9: Provide access for umbilical through chair. A) Loosen six Lift Arm Skin bolts enough to maneuver the Umbilical under it. B) Remove Umbilical Wire Bail. Note Do not install fasteners or mounting plates along the umbilical until it is completely routed through the chair and mounting arm. You may need to make adjustments as you go through the install. Lift Arm Skin Bolts Step 10: Route umbilical through chair. A) Begin routing Umbilical from the front of chair B) Align the Tape with the front of the indentation in the chair casting. C) Route the Umbilical through the chair casting as shown below. Note: Illustration shows Chair Casting with Skin and Seat missing for clarity. Wire Bail Chair Casting Casting Indentation Tape Step 11: Continue Routing Umbilical through Seat Casting. A) Route Umbilical up through the Pivot Hole into seat casting. B) Route Umbilical along the RIGHT SIDE and into the hole in the foot end. C) Route the Vacuum and Drain through the middle of the chair casting and into the hole in the foot end. 7
8 Step 12: Route Umbilical through the Console Mounting Arm. A) Route umbilical through the Console Mounting Arm as shown. B) Route the Vacuum and Drain lines through the Console Mounting Arm as shown. Umbilical Step 13: Make connections at the back of the chair A) Connect two LIN lines into the LIN Coupler. Adhere the coupler s adhesive back to the chair frame pocket as shown. B) Connect ground wire to the chair frame. Vacuum & Drain LIN Coupler Ground 8
9 Step 14: Hook springs back up. A) At the foot end of the chair, hook the springs onto the Trunnion Casting. Trunnion Casting Springs Snap Bushing Step 15: Install Delivery Unit Foot Control. A) Install Snap Bushing in the Light Bracket on the back of the chair. B) Route the Foot Control umbilical through the base exiting it out through the front of the chair, to the left side of the umbilical indentation in front. Equipment Alert Connections to the PC Board and Power vary slightly when using this kit, see Step 16. 9
10 Umbilical Plate Connect Ground Step 16: Make Special Kit Connections. A) Remove metal PCB Cover to access the Chair PCB. B) Remove the black tube-sleeve from the umbilical Power line grouping. C) Install the Blue and Brown Power wires into the Amp Connector. D) Plug the Amp Connector into J3 on the Chair PCB. E) Connect ground to the hole in the chair frame. F) Plug Green and Brown wire connector into J4 on the Chair PCB. G) Plug Red/ White/ Black wire connector into J5 on the Chair PCB. Note: Secure wiring to Lift Arm skin with zip ties. Metal PCB Cover Chair PCB Power Amp Connector Step 17: Secure Umbilical and Reinstall all Covers. A) Install Umbilical Plate (2 screws). B) Install Wire Bail and tighten bolts on Lift Arm Skin (See page 7). C) Connect Chair to Power source. D) Verify operation of the equipment. Power RD/ WH/BK Equipment Alert Ensure brown wire in power harness is in position 1 as shown. GN/ BR 10
11 XX-XXX 13 Note Parts not shown in proportion XXX xx Elevance Chair to Console Chair Conversion Kit (includes items 1 thru 15) a 10b (w/usb Hub Power) (w/usb Hub Power) Item Description Qty. 1 #10-24 X 1/2 screw 2 2 1/4 Clamp sleeve 1 3 Air control assembly w/drive air 1 4 Front cover 1 5 Zip ties 4 6 Console mounting arm 1 7 Foot-control, 4 port, wet-dry 1 8 Chair anchor kit 1 9 Molex plug (3 circuits) 1 10a 10b 115 VAC Power Supply 230 VAC Power Supply 11 Rotation Stop 2 12 Snap Bushing Sb Umbilical Plate Umbilical, Console Chair, 4 Ft Uni-Clamp, 1/8 Od Tube 4 16 Harness Midmark Corp. 60 Vista Drive Versailles, OH USA
Product Name Chair Conversion Kit (to LR Delivery Unit) Installation [Kit # xx]
Elevance Product Name Chair Conversion Kit (to LR Delivery Unit) Installation Installation [Kit #002-1966-xx] Attention: Use this kit to convert an Elevance Chair to a Chair with an Elevance LR mounted
More informationCylinder Rod End Replacement Kit [ ]
Cylinder Rod End Replacement Kit [002-2068-00] Contents: Installation...1 Special Tools: none Language of origin: English Step 1: Inspect components. Step 2: Position chair. A) Move the back section to
More informationSide Delivery Unit Installation
Side Delivery Unit Installation CONTENTS Mounting Location... 1 Minimum Cabinet Size Requirements... 1 Mounting Requirements... 1 Regulator Installation... 2 Cabinet Mount Bracket Installation... 2 Wall
More informationFlex Work Station Delivery Units Installation Guide
Flex Work Station Delivery Units Installation Guide Special Tools Level 1/4" Deep Well Socket 3/8" Masonary Bit 9/32" Wood Bit Hammer Drill Remove any packaging from the skid and the floor or wall mount
More informationSpring Bearing Rocker Replacement Installation [Kit # ] for Elevance Continental-Style Delivery Unit
Spring Bearing Rocker Replacement Installation [Kit # 002-2076-00] for Elevance Continental-Style Delivery Unit Note Use this kit to replace one or more Spring Bearing Rockers in an Elevance Continental-Style
More information630 (-010 thru -013, -020 thru -023)
60 (-00 thru -0, -00 thru -0) Headrests Actuators: Back Tilt Foot Upholstery: Premium UltraPremium Controls: Corded Hand Ctrl Corded Foot Ctrl Wireless Fuses Product Overview Headlock Components Seat Section
More information491 Harness Installation Kit
491 Harness Kit 002-0759-00 Kit Components: Qty Harness Assy... 1 Wire Clip... 2 Wire Tie (7 1/2 )... 5 Wire Tie (7 1/4 )... 4 Instruction... 1 Remove Back Cover Warning Disconnect Power before removing
More informationMidmark Light Install: L/R mounted on Ultra Chair
Midmark Install: L/R mounted on Ultra Chair warning Equipment is not suitable for use in the presence of a flammable anesthetic mixture. Applies to Models: 153914 (-002) 153915 (-002) Language of origin:
More informationTrack Light with Monitor Installation Guide
Track Light with Monitor Installation Guide This installation requires at least two service technicians. Track with light and monitor weight (max.) is 157 Lbs. (71 kgs). Applies to Models: 1531017 (-000
More informationProcenter Delivery, Console Mounted on an Elevance Chair Installation Guide
Procenter Delivery, Console Mounted on an Elevance Chair Installation Guide Language of origin: English Equipment Alert Do not remove wraps or packaging from the delivery flex arm assembly until it is
More informationProcenter Delivery Mounted on a Free Standing Treatment Console (FTC) Installation
Procenter Delivery Mounted on a Free Standing Treatment Console (FTC) Installation Electrical Requirements: 24 VAC, 3.2 Amp 13VAC, 2 Amp Attention These instructions apply to Midmark cabinetry. For other
More informationInstallation Instructions: Over-The-Patient Units (& Cuspidors) BDS-2500 BDS-2505 BDS-2510 BDS-2515 BDS-2520
Installation Instructions: Over-The-Patient Units (& Cuspidors) BDS-2500 BDS-2505 BDS-2510 BDS-2515 BDS-2520 X-Calibur BDS Delivery Systems Installation Instructions for BDS-2500, 2505, 2510, 2515, 2520
More informationKnee Crutches / Cladding [9A410 / 9A411 / 9A412 / 9A413]
Knee Crutches / Cladding [9A40 / 9A4 / 9A42 / 9A43] Intended Use: To support patient s knees / legs during examinations. Requirements: 604 / 622 / 623 models require a special cladding kit to accommodate
More informationTroubleshooting Guide: Elevance Delivery Systems
Troubleshooting Guide: Elevance Delivery Systems FOR USE BY MIDMARK TRAINED TECHNICIANS Contents Description / Links Troubleshooting Charts ICM Screens Assistant s Unit Instruments (Elevance & European)
More informationPart Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short Bracket PF3000 Pro
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short 2000105-2 1 PFadvantage Bracket PF3000 Pro 2000773 1 Cable Kit
More informationRadius Cuspidor (for Cascade 1040 or Decade 1011/1021 Chairs)
INSTALLATION INSTRUCTIONS Radius Cuspidor (for Cascade 1040 or Decade 1011/1021 Chairs) You Will Need: Hex key set Level Large flat head screwdriver Pliers 1/2" and 9/16" wrench Cutters Before Beginning
More informationMonitor Support Arms. Service and Parts Manual Part / Kit Numbers:
Monitor Support Arms Part / Kit Numbers: 153698 153699 153705 002-1836-00 153762 153763 153798 153823 153824 Service and Parts Manual FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY 004-0806-00 (7/30/15) Table
More informationSpecialty Chair Platform, Base
Specialty Chair Platform, Base Base Actuator Non-Rotational Base Column Top Components Scissors Components Rotational Base Base Shrouds Fuses Base Covers & Electrical Components Rotational Base, Base Shrouds
More informationInstallation instructions, accessories. Multimedia monitor with DVD, Dual screen. Multimedia monitor with DVD, Dual screen V1.
Installation instructions, accessories Instruction No 30756560 Version 1.2 5 Part. No. 30756177 Multimedia monitor with DVD, Dual screen Volvo Car Corporation Multimedia monitor with DVD, Dual screen-
More informationInstallation Instructions: Swing Mounted Units BDS-2575
Installation Instructions: Swing Mounted Units BDS-2575 X-Calibur Units Installation Instructions for BDS-2575 X-Calibur Dental Units 8-23-10 BDS Swing Mounted Units Installation Time: Approximately 2
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12
Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD
More informationLoose Components. VetPro 5000 Wall / Cabinet Mount Installation. Applies to Models:
VetPro 5000 Wall / Cabinet Mount Installation warning Equipment not suitable for use in the presence of a flammable anesthetic mixture. Applies to Models: 8001-001 8001-002 8001-005 8001-006 Loose Components
More informationSuspension System RS6582B
Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance
More information850 TETHER SWITCH KIT
850 TETHER SWITCH KIT P/N 2883823 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More information97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS
92RC60500 97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS Congratulations on your purchase of a new Rough Country 2 /3 Body Lift. We are committed to providing you with the best product available for the best
More informationPart Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Flow Sensor 4001356 1 Deflector plate 2000612-1 1
More informationINSTALLATION INSTRUCTION 88073
INSTALLATION INSTRUCTION 88073 Rev C FOR RANCHO SUSPENSION SYSTEMS RS6572 & RS6573: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationIllustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060
Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060 Great Plains Part #891-622C (Gandy Part #6245DS-TT) Great Plains Turbo-Till & Turbo-Chopper 2400/3000 Models 45
More informationRead and understand all instructions and warnings prior to installation of product and operation of vehicle.
#F9378 Installation Instructions 1998-2000 Ford Ranger 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products
More informationInstallation and Service Manual
RESIDENTIAL PLATFORM LIFTS RPL400 / RPL600 Installation and Service Manual WARNING! STRICT ADHERENCE TO THESE INSTALLATION INSTRUCTIONS IS REQUIRED to promote the safety of those installing this product,
More informationMF 9690, 9790, Challenger 660, 670
Ag Leader Technology Parts List Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No. MF 9690 MF 9790 Challenger 660 Challenger 670 Instruction
More informationService and Parts Manual
-00 thru -00 Power Female Procedure Examination Chair Service and Parts Manual Serial Number Prefixes: BK, V, DT & FH -00 thru -00 FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY SF- Part No. 00-000-00 Rev.
More informationINSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More informationFlow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Quick reference sheet 2002831-36 1 Installation instructions
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationPFadvantage JD 3300/4400/6600/7700; 4420
Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number 3 3 6 6
More informationWall / Casework Mounted Delivery Systems (Procenter)
20 20 0 0 40 40 2 3 0 4 60 60 5 6 7 80 80 00 00 2 3 4 Wall / Casework Mounted Delivery Systems (Procenter) Common Components...004-0859-99 2:00 / FTC Delivery Systems Side Delivery Systems... 004-0886-99
More informationFord 6.7 EGR Delete Kit
Fits: 2011 12 Powerstroke 6.7L Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** ***This kit is intended for off road use only.***
More informationFour Wheel Drive Kit Groundsmaster 580D
Four Wheel Drive Kit Groundsmaster 580D FORM NO. 957 Rev B Model No. 0599 00 thru 99999 INSTALLATION INSTRUCTIONS POTENTIAL HAZARD Traction Unit rolls over. WHAT CAN HAPPEN Bodily injury could occur. 4
More informationRUN/BRAKE/TURN AUXILIARY LIGHTS J
RUN/BRAKE/TURN AUXILIARY LIGHTS J06236 2018-05-31 GENERAL Kit Numbers 67800589A, 69202276 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harleydavidson.com
More informationIllustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060
Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060 Great Plains Part #891-561C (Gandy Part #6245DS-GP) For Great Plains Turbo-Max 2400, 3000, 3500 & 4000 Models 45
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationEssentials. Simple and Easy to Follow Installation Manual % Free Call! Expert Advice.
Essentials Simple and Easy to Follow Installation Manual % Free Call! %800-745-5337 Expert Advice DVD Headrest JK Wrangler Installation Instructions Note: Be sure to read this entire instruction sheet
More informationBX7460P Allure Tow Bar Operator Manual & Installation Instructions. ALLURE Tow Bar (10,000 lb) Pintle Coupler
Operator Manual & Installation Instructions ALLURE Tow Bar (10,000 lb) Pintle Coupler Hooking Up to Towed Vehicle 1. Position the towing vehicle on a level surface with a straight driveway ahead and engage
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SPEED CABLE SHIFTER units built before 4/30/12
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 6 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2"-
More informationASTRO AMC-2000 SERIES ENVELOPE FEEDER
ASTRO AMC-2000 SERIES ENVELOPE FEEDER PARTS CATALOG GROUP 1 Page 1 KEY # PART # DESCRIPTION QTY. KEY # PART # DESCRIPTION QTY. 1. 84-100-56B FRONT FRAME CLOSURE 1 24. 84-125-108 RETAINER STRAP ASSEMBLY
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SP.
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS MINI RACK OVEN OV310G ML-132515 A product of BAXTER MFG. CO., INC. 19220 STATE ROUTE 162 EAST, ORTING, WA 98360 FORM 43242 (October 2011) Table of Contents 3 ADVANCED CONTROL
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More informationINSTALLATION INSTRUCTION 88094
INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:
More informationINSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER
Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles MacDon M150 M200 PN: 602-0232-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before installing or operating
More informationFan, DVI Insert 31 and 33 DVI Installation Instructions (sku )
Packing List Fan, DVI Insert 31 and 33 DVI Left and Right Blower Assembly (with grommets and bushings) (2) Blower Mounting Nuts Wiring Harness Rheostat Snap Disc Rheostat Nut and Knob Nylon Rheostat Spacer
More informationRostselmash Torum 740
Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 740 Combine Kit Torum 740 4100762 1 Threaded Arm Assembly 2000311-2 1 Header
More informationInstallation Instructions: Side Delivery Units BDS-2555
Installation Instructions: Side Delivery Units BDS-2555 X-Calibur Units Installation Instructions for BDS-2555 X-Calibur Dental Units 7-18-06 BDS Side-Delivery Unit Installation Time: Approximately 1
More information»Product» Safety Warning
#F9387 Installation Instructions 1999-2003 Ford Super Duty 2/4wd Gas Only 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone
More information4 Suspension System. Ford Super Duty 4WD Part#:
Part#: 013414 4 Suspension System Ford Super Duty 4WD 2017 Rev. 092617 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 E-mail: tech-bds@sporttruckusainc.com Read And Understand All Instructions
More information-001. Air Lift Physician Stool. Serial Number Prefixes: BZ, V & VAF FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY -001
427-001 Air Lift Physician Stool Serial Number Prefixes: BZ, V & VAF 427-001 FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY SF-1254 Part No. 004-0038-00 Rev. F (11/18/14) TABLE OF CONTENTS Section/Paragraph
More informationw w w. h d o n l i n e s h o p. d e ELECTRA-GLO LIGHT BARS GENERAL INSTALLATION -J04723 REV Kit Number Models Kit Contents
-J07 REV. 00-0-0 GENERAL Kit Number -09 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only). Kit Contents See
More informationWheel Horse. 36 Tiller. Model No & Up. Operator s Manual
FORM NO. 8 9 Rev. A Wheel Horse 6 Tiller for Classic Garden Tractors Model No. 7970 690000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the
More informationINSTALLATION INSTRUCTIONS 88029
INSTALLATION INSTRUCTIONS 88029 FOR SUSPENSION SYSTEMS RS6503: JEEP WRANGLER (TJ) READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION REV F IMPORTANT NOTES! WARNING: This
More informationPFadvantage Metalfor Araus 1360
Metalfor Araus 1360 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor Araus 2005300-14 1 Display Bracket 4000134
More informationINSTALLATION AND OPERATING INSTRUCTIONS
ASTRO ENVELOPE FEEDER AMC-2000-5 FOR RYOBI 3302 / ITEK 3985 (2 COLOR) INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION Thank you for purchasing the Astro Envelope Feeder. It is fast, efficient, reliable,
More information»Product» Safety Warning
Read and understand all instructions and warnings prior to installation of product and operation of vehicle. 1. Zone Offroad Products recommends this system be installed by a professional technician. In
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationRear bumper cannot be used for towing after installation of the rear bumper relocation brackets.
921RC7020 *RC702BAG2* RC702BAG2 GM 07-13 4WD 1500 P/U 3 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More informationINSTALLATION INSTRUCTION 88092
INSTALLATION INSTRUCTION 88092 FOR RANCHO SUSPENSION SYSTEM RS6592: NISSAN XTERRA & 2WD FRONTIER READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES!
More informationINSTALLATION INSTRUCTION 88051
INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Ford F150 Super Crew Cab 2009 Current : 75141-15 www.bestop.com - We re here to help! Visit our web site and
More informationLexion 570R/575R, 580R/585R, 590R/595R
Note: Indented items indicate parts included in an assembly listed above Quantity by Model 2006+ All Years Part Name/Description Part Number 570R 575R 580R 585R Instruction Kit Lexion 570/580/590 2005500-5
More informationMODEL NUMBER 14527SB-LS PRODUCT NUMBER MFG. ID. NUMBER
ILLUSTRATED S LIST MODEL NUMBER SB-LS PRODUCT NUMBER 9 9 00-9 MFG. ID. NUMBER 9900900 009-0 -90 Rev. 0.09.09 SR AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL SB-LS (9900900), PRODUCT 9 9 00-9
More informationMaster Slave Converter [ VAC & VAC]
Master Slave Converter [002-1590-00-115 VAC & 002-1590-01 230 VAC] Contents: Installation...1 Wire Diagram...4 Exploded View...6 Intended Use: To provide simultaneous operation of up to five Midmark compressors
More information1/2 Ton Tahoe/Suburban/Yukon/Avalanche 4wd Part #: Rev
Rear Coil Spring Kit 1/2 Ton Tahoe/Suburban/Yukon/Avalanche 4wd 00-06 Part #: 021608 Rev. 040116 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail:
More informationIllustrated Parts List / / 924 SB
9SB Illustrated Parts List / 990000 / 9 SB AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL 9SBb (990000), PRODUCT 9 9 00-0 9 0 9 0 (EXPLODED) 9 0.0.00-B NOTE: All component dimensions given in U.S.
More information»Product» Safety Warning
#C1354 Installation Instructions 1999-2002 Chevy/GM 1500 4wd 3.5" Combo Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationThermoLite 36W Solar Panel Installation Guide
ThermoLite 36W Solar Panel Installation Guide Install applications supported by this guide: 1. Heat King (all models) 2. SB Domestic Rail Container (DRC front skin mounted) 3. Precedent Domestic Rail Container
More information8G Brake Assembly Alignment
8G Brake Assembly Alignment 8G (9-5250) This document explains how to do the 8G (9-5250) brake assembly alignment in order to eliminate noise in the drive system coming from the mis-aligned brake plates.
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SPEED CABLE SHIFTER units built before 4/30/12
Paso Robles, CA 93447 PAGE 1 OF 6 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302075
More information393: Multimedia system for the rear seat Multimedia system for the rear seat
393: Multimedia system for the rear seat S80 (07-), 2008, B8444S, TF-80SC AWD, L.H.D, YV1AH852881073834, 073834 4/1/2013 PRINT 393: Multimedia system for the rear seat Multimedia system for the rear seat
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HD BUMPER Kit 66240 (BLACK), 74760 (BLACK) & 74690 TUBELESS (TEXTURED BLK) For 03-Newer Chevy 3/4 Ton Trucks As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS.
More informationREAD AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE.
#9378 Installation Instructions 3 Body Lift Kit 1998-2000 Ranger READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE. SAFETY WARNING BDS Suspension
More informationAg Leader Technology. Parts List for Combine MF , 8780, White 9700
Parts List for Combine Quantity by Model Note: Indented items indicate parts included W in an assembly listed above 8 8 8 8 H 5 5 5 7 I 6 7 9 8 T Part Name/Description Part No. 0 0 0 0 E Instruction Kit
More informationASTRO AMC-2000 SERIES ENVELOPE FEEDER
ASTRO AMC-2000 SERIES ENVELOPE FEEDER PARTS CATALOG GROUP 1 Page 1 GROUP 1 1. 84-100-56B FRONT FRAME CLOSURE 1 25. 84-130-20 SKID WHEEL ASSEMBLY 1 2. 71-140-08 FRONT ENV. GUIDE ASSEMBLY, R/H 1 26. 123-0407
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More informationaxcs Chair Mounted Unit Installation, Operation and Care Manual
axcs Chair Mounted Unit Installation, Operation and Care Manual DentalEZ Group 2500 Highway 31 South Bay Minette, AL 36507 Table of Contents Section I Introduction Introduction... 2-3 Specifications...
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation
More informationINSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT
PART NUMBER: 0000-89-N30 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT APPLICABLE MODELS: 2016 > CX-9 PACKAGE CONTENTS: INSTALLATION INSTRUCTIONS QTY 1 CABLE TIE MOUNT QTY
More informationLower Adjuster Small Black Header Sensor Reversed
Parts List for Combine Quantity by Model Early Late Early Late Note: Indented items indicate parts included M M M M M M in an assembly listed above F F F F F F 7 7 8 8 8 8 5 6 5 5 6 6 Part Name/Description
More information3.5 inch A-Arm Lift Kit
16-010 3.5 inch A-Arm Lift Kit will fit CLUB CAR PRECEDENT installation instructions included: Main Suspension Assembly 2 Spindles 2 A-Arms 2 Rear Shock Mounting Plates 2 Rear Lift Blocks 2 U-Bolts 1 2
More informationMidmark Track Light Installation
Midmark Track Light Installation [Full size ceiling template is available: 003-1287-00] Applies to Models: 153910 (-002) 153656 (-001) Language of origin: English Physical Requirements warning Equipment
More information270 Series Stools. 270 Series. Service and Parts Manual. Serial Number Prefix: V & VAB. (270 thru 279) FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY
270 Series Stools Model Numbers: 270 Series (270 thru 279) Serial Number Prefix: V & VAB Service and Parts Manual FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY SF-190 Part No. 004-0549-00 Rev. (9/11/17)
More informationService Bulletin. HIITMill (X) Brake Lever Drift
HIITMill (X) Brake Lever Drift Applies to: HIITMill (9-4590) + HIITMIll X (9-4640) On some HIITMill and HIITMill X units, the brake lever can drift when the user is Rev. A applying load to the belt. This
More informationWOC & WOC Top & Back Installation Instructions
Shown with optional Sun Roof WOC-900500-2 & WOC-900501-2 Top & Back Installation Instructions Install Order! Heater Door System Wiper on to Windshield Windshield Rear Panel Top Panel Tools needed: 5/16
More informationAmTryke Adult Recumbent Model JT2000 #50-FC-2000
AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More information»Product» Safety Warning
#C9354 Installation Instructions 2001-2002 Chevy/GM 1500 2/4wd 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. 1. Zone Offroad
More informationR O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP
R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More information»Product» Safety Warning
#C9355 Installation Instructions 1999-2000 Chevy/GM 1500 2/4wd 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. 1. Zone Offroad
More information