FRONT TURN SIGNAL RELOCATION BRACKET (with Retro Turn Signals) BC

Transcription

1 Kit Includes: 1. Front Turn Signal Relocation Bracket 2. (2) M6x30 Screws 3. (2) M6x20 Screws 4. (2) Washers Fits The Following Motorcycles: Triumph Bonneville Triumph Thruxton Triumph Scrambler Tools Required: 4MM Allen Wrench 17MM Wrench for Turn Signals This is a high performance product and intended for race use applications! USE AT OWN RISK! WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/province and local/municipal laws and regulations. WARNING: It is recommended that this kit be installed by a certified Triumph technician, following the Triumph service manual to aid in proper fitting. Verify all torque specs in Triumph service manual. Other Items We Think You May Like Master Cylinder Cover Low Profile Front Sprocket Cover 1 Clutch Arm Finisher Chain Guard

2 Step 1: Disconnect Battery, Protect front fender with cloth or towel and remove the two 8mm rectifier bolts Step 2: Remove the two Phillips screws on the headlight bezel and open the headlight bucket Step 3: Pop out the plastic cable retainer that is holding down the front signal wires on the OEM bracket Step 4: Lift up gently on the two clips to disconnect the right turn signal from the headlight harness (-) Harness Black/White Dot = Turn Signal Black (+) Harness Green/White = Turn Signal White 2

3 Step 5: Lift up gently on the two clips to disconnect left turn signal from the headlight harness (-) Harness Black = Turn Signal Black (+) Harness Green/Brown = Turn Signal White Step 6: Feed the Black & White turn signal wires out of the back of the headlight bucket to free the OEM front turn signal assembly Step 7: Fasten your new signal bracket with screws and washers from the table below. 4mm Allen x 30mm (M6x30) screws when attaching: Signal Relocation Bracket, Rectifier and Cowl Bracket (Thruxton), 4mm Allen x 20mm (M6x20) screws when attaching: Signal Relocation Bracket and Rectifier or Signal Relocation Bracket and Cowl (Thruxton) or Signal Relocation Bracket by itself 3

4 Step 8: Remove nut and washer from the new Right signal and feed wires through bracket. Then feed wires through washer and nut and into the backside of the headlight bucket Step 9: Tighten right signal to bracket with a 17mm wrench Step 10: Connect RIGHT Turn Signal to RIGHT Harness Adapter. (-) Signal BLACK/WHITE = Harness Adapter BLACK (+) Signal BLACK = Harness Adapter RED Step 11: Connect RIGHT Harness Adapter to the RIGHT OEM Wiring Harness. (-) Harness Adapter BLACK = OEM Wiring Harness BLACK/ WHITE DOT (+) Harness Adapter RED = OEM Wiring Harness GREEN/ WHITE 4

5 Step 12: Now fasten Left Signal by feeding wires through bracket, washer, nut and into the backside of the headlight bucket. Tighten Left signal to relocation bracket with a 17mm wrench Step 13: Connect LEFT Signal to LEFT Harness Adapter. (-) Turn Signal BLACK/WHITE = Harness Adapter BLACK (+) Turn Signal BLACK = Harness Adapter RED Step 14: Connect LEFT Harness Adapter to LEFT OEM Wiring Harness. (-) Harness Adapter BLACK = OEM Wiring Harness BLACK (+) Harness Adapter RED = OEM Wiring Harness GREEN/ BROWN Step 15: Tuck excess turn signal wires under flexible clamp in bucket and press firmly to bend clamp into position to hold wires 5

6 Step 16: Replace the two Phillips screws to hold the headlight bezel assembly in place and tighten Step 17: Reconnect battery, Positive (+) side first and test your work. End: Congratulations! You have successfully completed the installation of your new Front Turn Signal Relocation Bracket by British Customs. 6