SERVICE MANUAL MODEL # ORDER # MODEL # ORDER # HD 2.3/24 P HD 2.5/27 P HD 3.0/30 P HD 3.8/35 P HD 3.

Transcription

1 SERVICE MANUAL CHAUD! READ OWNER'S MANUAL BEFORE OPERATION. LIRE LE MANUEL D'UTILISATEUR AVANT USAGE. VOR INBETRIEBNAHME UNBEDINGT BEDIENUNGSANLEITUNG DURSCHLESEN. NO UTILIZAR SIN ANTES NO HABER LEIDO EL MANUAL. OIL ALERT WHEN OIL LEVEL LOW, ENGINE STOPS IMMEDIATELY. MODEL # ORDER # HD 2.3/24 P HD 2.5/27 P HD 3.0/30 P HD 3.8/35 P HD 3.5/40 P PC PC PC PC PC MODEL # ORDER # DB DB DB DB DB DG DG DG DG DG

2 CONTENTS Exploded View... 4 Exploded View Parts List Specifications... 6 Gun and Wand Exploded View and Parts List G Pump Exploded View and Parts Lisst G.1 Pump Exploded View and Parts List S.3 Pump Exploded View and Parts List UU1 Unloader Exploded View and Parts List VBA Unloader Exploded View and Parts List Troubleshooting Preventative Maintenance Oil Change Record Model Number Serial Number Date of Purchase The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. 3

3 OPERATOR S MANUAL PRESSURE WASHER 18 Pump Assy w/ EZ Start for 4000 PSI Models EXPLODED VIEW Pump Assy w/e-z Start Valve for 3000 & 3500 PSI Models Pump for 3500 PSI Models WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Operation of This Equipment May Create Sparks That Can Start Fires Around Dry Vegetation. A Spark Arrestor May be Required. The Operator Should Contact Local Fire Agencies for Laws or Regulations Relating to Fire Prevention Requirements. 20 CHAUD! READ OWNER'S MANUAL BEFORE OPERATION. LIRE LE MANUEL D'UTILISATEUR AVANT USAGE. VOR INBETRIEBNAHME UNBEDINGT BEDIENUNGSANLEITUNG DURSCHLESEN. NO UTILIZAR SIN ANTES NO HABER LEIDO EL MANUAL. OIL ALERT WHEN OIL LEVEL LOW, ENGINE STOPS IMMEDIATELY Pump Assy for 2400 & 2700 PSI Models

4 ITEM PART NO. DESCRIPTION QTY 1 Engine, See Specifi cations Page 2 Pump, See Specifi cations Page 3 Unloader, See Specifi cations Page Pump Protector, 1/4" Pump Protector,1/2" 1 (4000 PSI Models Only) Swivel, 1/2" MP x 3/4" GHF Nipple, 3/8" x 3/8" NPT 1 ST Male Hose, 1/4" Push-on 14 in (E-Z-Start Models Only ) Hose, Barb, 1/4" Barb x 1/8" MP, 90 (3000 & 3500 PSI Models) Hose Barb, 1/4' Barb x 1/4" Pipe (3000, 3500 & 4000 PSI) Valve, E-Z Start 3/8" MPT x 1/8" FPT (3000, 3500 & 4000 PSI) Base, CW Direct, Black Base, CW Direct Red 1 (DB Models Only) Clamp, Hose (E-Z Start Models) Bolt, 3/8" x 1-1/4" NC, HH 4 (3000, 3500 & 4000 PSI Only) Bolt, 5/16"-24 x 3/4" Injector, Detergent, Assembly 1 (All Models) Injector, Chemical, Non-Adjust Strainer, Plastic, 1/4" Hose Barb Tube, 1/4" x 1/2" Clear Vinyl 6 ft Hose Clamp Label, Instructions 1 15 Hose High Pressure, See Specifi cations Page 16 Gun, See Specifi cations Page 17 Wand, See Specifi cations Page 18 Nozzle Size, See Page 18 For Proper Size Nozzle Kit 3.0 (2400, 2700 PSI) Nozzle, Red Nozzle, Yellow Nozzle, Green Nozzle, White Nozzle Kit 3.5 (3000, 4000 PSI) Nozzle, Red Nozzle, Green Nozzle, White Nozzle Kit 4.0 (3500 PSI) Nozzle, Red Nozzle, Yellow Nozzle, Green Nozzle, White Nozzle, Compl, QCEM-6540, Brass (All Models) Axle, 5/8" x " Long Label, HOT 1 EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY Bolt, 5/16" x 1-1/2", NC HH 4 (2400, 2700 PSI Models) Bolt, 3/8" x 1-3/4" Tap 4 (3000, 3500, 4000 PSI Models) Washer, 3/8" SAE, Flat Nut, 3/8" ESNA, NC Bolt, 3/8" x 2" NC, HH Retainer Bracket, Handle, Blk Retainer Braket, Handle, Red 2 (DB Models Only) Nut, 1/4" ESNA, NC Washer, 1/4" Flat Grommet, Nozzle Holder Nut, 5/16" Whiz Loc Flange Handle, Grab, Chrome Handle, Grab, Red 1 (DB Models Only) Plate, Warning, Black Hanger, Hose/Wand Bolt, 1/4"-20 x 1-3/4", Cge, Zc Handle, Lower Grab, Chrome Handle, Lower Grab, Red 1 (DB Models Only) Pad, Soft Rubber Washer, 3/8" x 1" Steel Bolt, 3/8" x 2-1/2" HH, Grd Bolt, Carriage, 5/16" x 1-3/4" Washer, 5/16" Flat Nut, 5/16" ESNA, NC Handle, Bumper, Chrome Handle, Bumper, red 1 (DB Models Only) Bushing, 5/8" Snap Wheel & Tire Assy, 2 10" Steel Rim w/tube Collar, 5/8" Bore Shaft Label, Cool Engine 1 Before Filling Washer, 5/8" Flat Key, Sqr x 1.75" 1 (2400, 2700 PSI Models) Key, SQR X 2.125" 1 (3000, 3500, 4000 PSI Models) Label, Manufacturer's Cleaning 1 Solution Nut, 5/16" ESNA, NC 4 (2400, 2700 PSI Models) Nut, 3/8" ESNA, NC 4 (3000, 3500, 4000 PSI Models) PRESSURE WASHER OPERATOR S MANUAL 5

5 OPERATOR S MANUAL PRESSURE WASHER EXPLODED VIEW PARTS LIST (CONT.) ITEM PART NO. DESCRIPTION QTY Washer, 5/16" Flat 8 (2400, 2700 PSI Models) Washer, 3/8" Flat 12 (3000, 3500, 4000 PSI Models) Tee, 1/4" Branch, Male Label, Regulation Elbow, 3/8", Str 90 Deg, Steel 1 (4000 PSI Models) Hose Barb 1/4" x 1/8" Npt Male 1 (4000 PSI Models) SPECIFICATIONS Machine Pressure Nozzle Hose Pump Pump Unloader Engine Model GPM (PSI) Size Part # Model Part # Part # Engine Part # HD 2.3/24 P KG2530G GC160 (163cc) HD 2.5/27 P KG2530G GX200 (196cc) HD 3.0/30 P KG3035G GX270 (270cc) HD 3.8/35 P KS4040GR GX390 (390cc) HD 3.5/40 P KS3540GR GX390 (390cc) Machine Pressure Nozzle Hose Pump Pump Unloader Engine Model GPM (PSI) Size Part# Model Part # Part # Engine Part # PC LG2530G GX160 (163cc) PC LG2530G GX200 (196cc) PC LG3035G EX27 (265cc) PC LS4040GR GX390 (390cc) PC LS3540GR GX390 (390cc) Machine Pressure Nozzle Hose Pump Pump Unloader Engine Model GPM (PSI) Size Part # Model Part # Part # Engine Part # DB HG2530G GC160 (163cc) DB HG2530G GX200 (196cc) DB HG3035G GX270 (270cc) DB HS4040GR GX390 (390cc) DB HS3540GR GX390 (390cc) Machine Pressure Nozzle Hose Pump Pump Unloader Engine Model GPM (PSI) Size Part # Model Part # Part # Engine Part # DG KG2530G GC160 (163) DG KG2530G GX200 (196) DG KG3035G GX270 (270) DG KS4040GR GX390 (390) DG SS3540GR GX390 (390)

6 HOSE & SPRAY GUN EXPLODED VIEW PRESSURE WASHER OPERATOR S MANUAL HOSE & SPRAY GUN EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY 1 Hose High Pressure, See Specifi cations page Gun, St-1500 (HD & DG , 2700, 3000 & 3500 PSI Models) Gun, M407 (HD & DG 4000 PSI Models Only) Gun, Sk2, 3/8" Inlet, Lance 22mm, Coupler (PC3 2400, 2700, 3000 & PC PSI Models) AL5 Gun 4000 PSI (PC PSI Models Only) AL12 Eagle3 Trigger Gun (DB 2400, 2700, 3000 & 3500 PSI Models) AL5 Gun 4000 PSI (DB 4000 PSI Models Only) Wand Assy, Side Grip w/1/4" Coupler (HD & DG Models) Wand, 18" M22 x 1/4" QC (PC3, PC4 & DB Models) Coupler, Twist Connect, M22-Fx3/8' Fnp (All DB Models & PC PSI Models Only) 1 Not shown 7

7 OPERATOR S MANUAL PRESSURE WASHER KG2530G LG2530G HG2530G 2530G PUMP EXPLODED VIEW TORQUE SPECS Item # Ft.-lbs G PUMP EXPLODED VIEW PARTS LIST 8 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY Crankcase Manifold Stud Bolt 8 2* See Kit Below Plunger Oil Seal Washer 8 3* See Kit Below O-Ring Ø1.78 x Copper Washer 3/8" 1 4* See Kit Below Pressure Ring, 15mm Brass Plug 3/8" 2 5* See Kit Below U-Seal, 15mm Hexagonal Screw 9 6* See Kit Below Intermediate Ring 15mm Bearing Cover 1 7* See Kit Below Backup Ring 15mm Seal Bearing 1 8* See Kit Below U-Seal, 15mm Snap Ring 1 9* See Kit Below Support Ring, 15mm Ball Bearing Brass Plug, 1/2" Crankshaft (2530G) Copper Washer 1/2" Crankshaft (3030G) Manifold Housing Oil Dip Stick 1 13* O-Ring Ø1.78 x O-Ring 3.53 x * See Kit Below Valve Assembly Needle Roller Bearing 1 15* O-Ring Ø2.62 x Engine Flange Valve Plug Spring Washer Washer, Copper Flange Screw Brass Plug G1/4 1

8 ITEM PART NO. DESCRIPTION QTY Crankshaft Seal 1 40* See Kit Below Plunger Nut 3 41* See Kit Below Copper Spacer 3 42* See Kit Below Plunger, 15mm 3 43* See Kit Below Copper Spacer 3 44* See Kit Below O-Ring Ø1.78x * See Kit Below Tefl on Ring Plunger Rod Connecting Rod Pin Connecting Rod Spring Washer Connecting Rod Screw O-Ring 2.62 x Crankcase Cover Gasket, G3/ Sightglass G3/4 1 * Part available in kit (See below) 2530G PUMP EXPLODED VIEW PRESSURE WASHER OPERATOR S MANUAL REPAIR KIT NUMBER KIT DESCRIPTION Plunger Seal 15mm Complete Seal Packing 15mm Plunger 15mm Complete Valve Plunger Oil Seals ITEM NUMBERS INCLUDED 3, 5, 7, 8, 9 3, 4, 5, 6, 7, 8, 9 40, 41, 42, 43, 44, 45 13, 14, 15 2 NUMBER OF CYLINDERS KIT WILL SERVICE

9 OPERATOR S MANUAL PRESSURE WASHER KG3035G LG3035G HG3035G1 3035G.1 PUMP EXPLODED VIEW TORQUE SPECS Item # Ft.-lbs G.1 PUMP EXPLODED VIEW AND PARTS LIST ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY Crankcase Manifold Stud Bolt 8 2* See Kit Below Plunger Oil Seal Washer 8 3* See Kit Below O-Ring Ø1.78 x Copper Washer 3/8" 1 4* See Kit Below Pressure Ring, 15mm Brass Plug 3/8" 2 5* See Kit Below U Seal Assy, 15mm Hexagonal Screw 9 6* See Kit Below Intermediate Ring 15mm Bearing Cover 1 7* See Kit Below Backup Ring, 15mm Seal Bearing 1 8* See Kit Below U-Seal Assy, 15mm Snap Ring 1 9* See Kit Below Support Ring 15mm Ball Bearing Brass Plug, 1/2" Crankshaft (3035G1) Copper Washer 1/2" Crankshaft (3535G1) Manifold Housing Crankshaft (4030G1) 1 13* O-Ring Ø1.78 x Set Screw 1 14* See Kit Below Valve Assembly Oil Dip Stick 1 15* O-Ring Ø2.62 x O-Ring 3.53 x Valve Plug Needle Roller Bearing Washer, Copper Engine Flange Brass Plug G1/ Spring Washer 4 10

10 3035G.1 PUMP EXPLODED VIEW AND PARTS LIST (CONT) ITEM PART NO. DESCRIPTION QTY Flange Screw Crankshaft Seal 1 47* See Kit Below Plunger Nut 3 48* See Kit Below Copper Washer 3 49* See Kit Below Plunger, 15mm 3 50* See Kit Below Copper Spacer 3 51* See Kit Below O-Ring Ø1.78x * See Kit Below Tefl on Ring Plunger Rod Connecting Rod Pin Connecting Rod Spring Washer Connecting Rod Screw Sight Glass, G3/ Gasket, G3/ Crankcase Cover O-Ring 2.62 x * Part available in kit (See below) PRESSURE WASHER OPERATOR S MANUAL REPAIR KIT NUMBER KIT DESCRIP- TION ITEM NUM- BERS INCLUDED Plunger Seal 15mm 3, 5, 7, 8, 9 Complete Seal Packing 15mm 3, 4, 5, 6, 7, 8, 9 Plunger 15mm 47, 48, 49, 50, 51, 52 Complete Valve Plunger Oil Seals 13, 14,

11 OPERATOR S MANUAL PRESSURE WASHER KS4040GR LS4040GR HS4040GR.3 S.3 PUMP EXPLODED VIEW KS3540GR LS3540 GR HS3540GR SS3540GR.3 TORQUE SPECS Item # Ft.-lbs S.3 PUMP EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY Crankcase O-Ring Ø 2.62 x * See Kit Below Plunger Oil Seal Snap Ring 1 3* See Kit Below O-Ring Ø1.78 x Double Row Ball Bearing 1 4* See Kit Below Pressure Ring Crankshaft (3540G.3) 1 5* See Kit Below U-Seal, 15mm Crankshaft (4040G.3) 1 6* See Kit Below Intermed. Ring 15mm Set Screw 1 7* See Kit Below U-Seal, 15mm Oil Dip Stick Copper Washer 1/2" O-Ring Ø 3.53 x Brass Plug, 1/2" Needle Roller Bearing Manifold Housing Gasket 1 11* O-Ring Ø2.62 x Screw, Set 1 12* See Kit Below Valve Assembly Engine Flange 1 13* O-Ring Ø2.62 x Flange Screw Valve Plug Crankshaft Seal Manifold Stud Bolt Spring Washer Washer 8 46* See Kit Below Plunger Nut, M Copper Washer 3/8" 1 47* See Kit Below Washer, Copper, 9.2 x Brass Plug 3/8" 2 48* See Kit Below Plunger, 15mm Washer, M6 x * See Kit Below Copper Spacer Hexagonal Screw Closed Bearing Housing 1 12

12 S.3 PUMP EXPLODED VIEW PARTS LIST (CONT.) ITEM PART NO. DESCRIPTION QTY 50* See Kit Below O-Ring Ø1.78x * See Kit Below Tefl on Ring Plunger Rod Connecting Rod Pin Connecting Rod Spring Washer Connecting Rod Screw O-Ring 2.62 x Crankcase Cover O-Ring, Ø 1.78 x Sight Glass, G3/4 1 * Part available in kit (See below) REPAIR KIT NUMBER KIT DESCRIPTION ITEM NUMBERS INCLUDED Plunger U-Seal 15mm Complete U-Seal Packing 15mm Plunger 15mm Complete Valve 3, 5, 7 3, 4, 5, 6, 7 46, 47, 48, 49, 50, 51 Plunger Oil Seals 11, 12, 13 2 PRESSURE WASHER OPERATOR S MANUAL NUMBER OF CYLINDERS KIT WILL SERVICE

13 OPERATOR S MANUAL PRESSURE WASHER UU1 UNLOADER EXPLODED VIEW UU1 3500PSI, UNIVERSAL UNLOADER (SPARE) UU1 UNLOADER EXPLODED VIEW PARTS LIST 14 ITEM PART # DESCRIPTION KIT QTY Piston Housing D 1 2 Piston C, D 1 3 Piston O-Ring Back Up A, D Main Block Piston Ring D 1 6 Ball Seat C, D 1 7 O-Ring 10.5 ID x 1.5 CS A,C,D 1 8 Plunger B Plunger Housing 1 10 Bypass Spring C, D Low Pressure Port Sliding Connector, 30mm Sliding Connector, 40mm, Long Sliding Connector H 1/2" Sliding Connector H 3/8" Plug 5/8-18 UNF D 1 15 O-Ring 12 ID x 2 CS A, D 2 16 O-Ring 6 ID X 2 CS A, D 1 ITEM PART # DESCRIPTION KIT QTY Sliding Connector Guide 1 18 O-Ring Backup A, D 1 6 x 1.45 x Ball Housing Assy C, D 1 20 O-Ring 6.75 x 1.78 BN80 A, D 1 21 Spring Seat C, D 2 22 Plunger Spring B Banjo Bolt 1/2" Short Banjo Bolt 1/2"-1/4" NPT Short Banjo Bolt 3/8" Short Seal Washer 3/8" Seal Washer 1/2" Seal Washer 3/8" 2 27 O-Ring 15 ID x 2CS A,B,D Plug, 1/4" Countersunk 1 Kit A O-Ring Repair Kit Kit B Outlet Kit Kit C Stem Basic Kit Kit D UU1 Complete Stem Kit

14 UNLOADER (VBA), VBA UNLOADER EXPLODED VIEW PRESSURE WASHER OPERATOR S MANUAL VBA UNLOADER EXPLODED VIEW PARTS LIST ITEM PART # DESCRIPTION KIT QTY 1 Body Valve (KG) 1 Body Valve (KS) 1 2 O-Ring A, C 1 3 Seat C 1 4 Ball, Sub Assy C 1 5 O-Ring A Guide Bushing 1 7 Tefl on Ring 1 8 O-Ring A 1 9 O-Ring A Connector 1 11 Tefl on Ring A 1 12 Stem C Connector Female 1 14 O-Ring A, B 1 15 Spring B 1 16 Poppet B 1 ITEM PART # DESCRIPTION KIT QTY Seal Washer 3/8" Banjo Bolt 3/8" Solid Cap Banjo Bolt 1/2", w 1/4" Pilot Seal Washer 1/2" 2 21 Plate C 1 22 Spring C Set Screw Nut Brass Handle Plug, 1/4" Countersunk 1 Kit A O-Ring Repair Kit Kit B Outlet Kit Kit C Stem Basic Kit 15

15 PRESSURE WASHER Troubleshooting Guide TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION LOW OPERATING PRESSURE FLUCTUATING PRESSURE PRESSURE LOW AFTER PERIOD OF NORMAL USE ENGINE WILL NOT START OR STOPS WHILE OPERATING ENGINE IS OVERLOADED WATER OR OIL LEAKING FROM BOTTOM OF PUMP PRESENCE OF WATER IN PUMP OIL Insuffi cient water supply. Closed faucet. Inlet hose kinked Clogged inlet hose strainer Faulty or improperly adjusted unloader valve Worn packing in pump Machine has been stored in freezing temperatures Slow engine RPM Worn or dirty pump valves Nozzle is obstructed Pump sucking air, inlet hose leaking Nozzle worn Unloader valve worn Low oil shutdown Out of gas Water in gasoline Nozzle partially blocked Excessive pressure from high engine RPM A small amount of leaking is normal Water sprayed at machine High humidity in air Piston packing worn. Oil seal worn. Use larger garden hose; clean inlet water screen. Open faucet. Check plumbing system for leaks. Re-tape leaks with Tefl on tape. Adjust unloader for proper pressure. Install repair kit when needed. Contact local dealer. Contact local dealer. Thaw out machine completely, including hose, spray gun and wand. Contact local dealer. Contact local dealer. Blow out or remove debris with fi ne needle. Check all pump lines and connections. Replace nozzle. Replace unloader valve. Fill engine with oil. Fill fuel tank. Drain gas tank; fi ll with clean fuel. Clean nozzle. Adjust engine throttle to lower RPM. If excessive leaking occurs, Contact local dealer. Change oil. Direct spray away from machine. Check and change oil twice as often. Contact local dealer. 16

16 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION ENGINE OPERATES FOR 15 MIN. THEN STOPS Not enough gas or engine oil Vapor lock developed by heat of day Obstruction in fuel fi lter Fill tank with gas. Check oil level. Keep gas tank full to avoid vapor locking. Clean or replace fuel filter. ENGINE LACKS Dirty air filter Replace air filter. POWER ENGINE FALTERS Choke is opened too soon Move choke to halfway position until engine runs smoothly. WATER DRIPPING Piston packing worn Contact local dealer. FROM UNDER PUMP O-Ring plunger retainer worn Contact local dealer. Cracked piston Contact local dealer. OIL DRIPPING Oil seal worn or damaged Contact local dealer. WATER LEAK- ING FROM PUMP PROTECTOR NO DETERGENT Spray gun closed with machine running 5 minutes or longer Excess water supply pressure Detergent suction tube not properly connected to machine Open spray gun or turn off machine. Place a pressure regulator at end of 50' garden hose. Check connection. PRESSURE WASHER Troubleshooting Guide GARDEN HOSE CONNECTION LEAKS SPRAY WAND LEAKS Detergent is too thick Detergent filter valve is at lowest setting Filter on detergent suction tube is clogged Damaged or clogged detergent suction tube A high pressure nozzle is attached. Discharge nozzle is obstructed Loose fi ttings Missing/worn rubber washer Spray wand not properly attached Broken o-ring Dilute detergent. For best results, use manufacturers detergent. Set detergent filter valve to a higher setting. Run warm water through fi lter to remove debris. Remove obstruction or replace detergent suction tube. Replace with black detergent nozzle. Blow out or remove debris with fi ne needle. Tighten fittings. Insert new washer. Slide the spray wand into the gun. Turn the wand collar clockwise onto the spray gun threads until tight. Call your distributor and order an o-ring. PUMP IS NOISY Pump is sucking air Check that hoses and fi ttings are air tight. Turn off machine and purge pump by squeezing trigger gun until a steady fl ow of water emerges through nozzle. 17

17 OPERATOR S MANUAL PRESSURE WASHER PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform maintenance more often under severe conditions. Engine Oil Air Cleaner/Filter Engine Fuel Filter Spark Plug Maintenance Clean Fuel Tank(s) Replace Fuel LInes MAINTENANCE SCHEDULE Inspect Daily Change First month or 20 hours. Every 100 hours or every 6 months after first month. Filter Every 50 hours. Inspect Clean Inspect Pump Oil Change Replace High Pressure Nozzle Replace Quick Connects/O-Rings Clean Water Screen/Filter Replace HP Hose Every 50 hours Monthly 500 hours or 6 months 300 hours or annually Annually Annually Oil level daily After fi rst 50 hours, then every 500 hours or annually Every 6 months Annually/As needed Weekly Annually (if there are any signs of wear) OIL CHANGE RECORD Check pump oil and engine oil level before fi rst use of your new pressure washer. Date Oil Changed Month/Day/Year Estimated Operating Hours Since Last Oil Change Date Oil Changed Month/Day/Year Estimated Operating Hours Since Last Oil Change 18

18 Form # Revised 07/13 Printed in U.S.A. or Mexico