E-manage ignition timing with DLI 4AGZE and 7MGTE engines
|
|
- Lucas Gordon
- 5 years ago
- Views:
Transcription
1 E-manage ignition timing with DLI 4AGZE and 7MGTE engines Background Some Toyota ECUs (such as the 4AGZE and 7MGTE) expect a return signal from the Ignitor for each ignition signal sent. The expected IGf signal is a ground signal (from the igniters) in response to a charge signal (from the IGt ECU point to the igniter). Problem When using the e-manage s ignition harness with these ECUs the maximum advance/retard that can be set is around +/- 6 degrees. Any more than this will result in an error being detected as there will be a time difference between the IGt signal being sent and the IGf signal being received by the ECU. This will result in the Check Engine light coming on, base ignition timing being set and in some cases the injectors may be shut-off. This restricts usage of the e-manage s ignition timing function to only +/- 6 degrees. Solution There is an IGf Signal Generation Circuit within the Igniter which creates the IGf signal using a switching transistor from the same signal that is sent out of the igniter to the ignition coil. This circuit can be created external to the igniter and can be used to generate an IGf signal directly from the ECUs IGt signal before the e-manage intercepts (and alters) the IGt signal. Using this external circuit, the ECU is provided with a consistent IGf signal even if the actual ignition event is earlier or later than the IGt signal is triggering. ECU Ground External IGf generation circuit CH1 out CH1 in E-manage Ignition Harness Page 1 of 5
2 Making the circuit You will need the following tools: Soldering iron (and solder) Wire stripper 2cm Heat-shrink tubing (and lighter). You will need the following parts: NPN 2N3904 switching transistor 1watt 1K (1000) ohm resister Veroboard (at least 3x9 holes) 3 x 10cm lengths of different coloured wires. 1. Cutdown the veroboard using a hacksaw or sharp knife to the correct size. Note: I found some veroboard that had 2 complete tracks and then 2 broken tracks and cut it so there was a complete track along each long edge and 2 incomplete tracks in the middle. 2. Bend the pins of the transistor so it can be inserted in the veroboard. 3. Bend the ends of the resistor so it can be inserted veroboard. Your parts should look something like this: 4. Solder the transistor into one end of the veroboard so that pin 1 and pin 3 are using the complete tracks. Note: refer to picture below for pin locations on the transistor. 5. Solder the resistor in-line with pin 2 and bridge the points between pin 2 and the resistor. 6. If you have used veroboard without complete tracks, solder links between pin 1 and the end of that track and pin 3 and the end of that track. 7. Solder the 3 different colour wires onto each of the 3 track ends and note which colours you used for each of the pins. 8. Clip off the excess pins and wires from the back of the veroboard, check over all of your connections and either heat-shrink the circuit or install it in a small box for protection. Page 2 of 5
3 This is the circuit using a veroboard with tracks: This is the circuit using a veroboard without tracks (and therefore with links): Installing the circuit (permanently) 1. Cut the IGt wire farther away from the ECU than where the RPM signal has been spliced into it. 2. Solder the CH1 in wire (from the ignition harness) and the pin 2 wire (from the external IGf generation circuit) to the IGt wire coming from the ECU and heat-shrink the joint to protect it. 3. Solder the CH1 out wire to the IGt wire going to the igniter and heat-shrink the joint to protect it. 4. Splice the pin 1 wire (from the external IGf generation circuit) to the ECU ground wire (which you used for the E-manage ground: E) and heat-shrink the joint to protect it. 5. Cut the IGf wire at a similar length from the ECU as the IGt was cut. 6. Solder the pin 3 wire (from the external IGf generation circuit) to the IGf wire going to the ECU and heat-shrink the joint to protect it. 7. Heat-shrink the IGf wire coming from the igniter to protect it from shorting out. Installing the circuit (non-permanently) As the IGf signal is a fail-safe feature, bypassing the true IGf signal (from the igniter) will remove the fault checking capability of the igniter/ecu. Therefore, you may want to consider installing the circuit using bullet connectors on the IGf wire so that you can swap the external IGf generated signal with the true IGf signal easily. To install the circuit in this manner, perform steps 1-5 and: 6. Install a male bullet connector on the IGf wire going to the ECU 7. Install a female bullet connector on the pin 3 wire (from the external IGf generation circuit) 8. Install a female bullet connector on the IGf wire coming from the igniter and heat-shrink the connector to protect it from shorting out. 9. Connect the male bullet (on the IGf wire going to the ECU) to the female bullet going to the IGf generation circuit. Page 3 of 5
4 I went one step further and used bullet connectors for all of the connections (so I can remove the whole circuit if I need to). The top wire in the above picture is the ground signal (which has a male bullet coming off for the e- manage ground wire). I tapped a small wire with a male bullet off a ground point on the ECU. The middle wire (which has an adapted splitter that comes with the e-manage) is the IGt feed. The male bullet goes into a female bullet attached to the IGt point on the ECU (see below picture) and the two female points are used for the e-manage CH1 in signal and the e-mange RPM signal. Finally the bottom wire is the IGf generator wire which is connected as described in steps 6 to 9 above. Note: you can easily remove the pins from an ECU plug (see above) by inserting a small screwdriver into the plug from the ECU side and levering the small tab that holds the point in. You can then pull on the wire and the point will slide out of the plug (don t forget which point it came out from!). If you ever need to check to see if your igniter is faulty, you can: 1. Change to an ignition map that has less than +/- 6 degrees of advance/retard (it is probably best to switch to a standard map with all zeros) 2. Swap the pin 3 wire (coming from the external IGf generation circuit) with the IGf wire coming from the igniter by disconnecting the joint and connecting the other female bullet. Page 4 of 5
5 How does it work? An NPN transistor is a small and fast switch that allows a signal to flow from the collector to the emitter when a signal is received from the base. In the IGf generation circuit, when there is an IGt signal (connected to the base) the transistor permits a signal to flow from the ECU Ground (connected to the collector) to the IGf input on the ECU (connected to the emitter) which grounds the IGf point each time an IGt signal is received. Other thoughts/information Although the DLI setup also uses another ECU signal to the igniter (IGd on 4AGZE and IGdA/IGdB on 7MGTE) to trigger which coil to fire, intercepting the IGt signal and selecting a distributor configuration works fine. This is initially a little confusing, but looking at the following picture shows that the IGt signal is constantly oscillating regardless of which coil is being fired. References and thanks Thanks to Rollamods from for informing me of the Greddy e-manage and also the existence of this circuit (and for the second photo of the circuit). Thanks to tsupra33 from the E-manage Yahoo Group for the diagram of the 7MGTE circuit in the files section of the E-manage Yahoo Group. Major thanks to John Simmerman from the Supra Owners Group International (SOGI) for originally designing the circuit. Diagrams of Toyota ignition setup came from Definition of transistor s operation is loosely based on an explanation given in the Beginner s Guide to Electronics by Martin T. Pickering available free from The Cool Bookshop. Cheers, JamitGZE. Page 5 of 5
Lakela nd H2 Low Speed Stator Coil Installation
Lakela nd H2 Low Speed Stator Coil Installation Step 1: Place the stator assembly on a padded surface to protect the plastic signal generators, and orient it as shown in figure 1. The low speed coil is
More informationFabricating and Installing Headlight Relays. Mike Graham
Fabricating and Installing Headlight Relays Mike Graham For some time I had been reading about the benefits of installing headlight relays. As I understand it, there are two principal benefits: the load
More information72 Mustang Mach 1 tachometer cluster and gauge conversion
72 Mustang Mach 1 tachometer cluster and gauge conversion Dated: 02-17-2009 (drafted by a Chevy person working on his first Ford -not good-) Revised: 11-05-2010 The following information pertains to how
More informationGreddy E-manage Installation and Tuning Information
Greddy E-manage Installation and Tuning Information Overview The Emanage has a lot of functionality considering it is still a piggyback type engine management system and not a full standalone. By itself,
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationWARNING! DIGITAL TUNING, INC. TAKES NO RESPONSIBILITY FOR DAMAGE TO ECU OR CAR DUE TO IMPROPER INSTALLATION OR MISUSE OF PRODUCT.
digital tuning Rtek7 ECU Upgrade for S5 Turbo II WARNING! DIGITAL TUNING, INC. TAKES NO RESPONSIBILITY FOR DAMAGE TO ECU OR CAR DUE TO IMPROPER INSTALLATION OR MISUSE OF PRODUCT. IT IS YOUR RESPONSIBILITY
More informationInstallation Instructions for the Plug & Play Chrysler/Dodge/Jeep Remote Start Package w/mux T5
v1.01 12/14/2102 Installation Instructions for the Plug & Play Chrysler/Dodge/Jeep Remote Start Package w/mux T5 Review the remote start installation manual for safety instructions! Overview Your kit consists
More informationSAISBM V36W Installation Instructions
The Original Secondary Air Injection System Bypass Kit SAISBM V36W Installation Instructions All Applicable Toyota/Lexus Vehicles Introduction: The Secondary Air Injection System (SAIS) bypass module is
More information750 Paso Wiring Upgrade
750 Paso Wiring Upgrade Supplies required: 2 Bosch 30A/12V Relays # #0 332 209 150 (with mounting tab) 1 30 Amp fuse holder 1 10 Amp fuse holder 12 inches of brown 12 gauge wire 60 inches of red 14 gauge
More informationPLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!!
JDM power folding mirror switch install into stock USDM harness. By: Greg L., Zeke21 on twinturbo.net PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!! This is how I was able to get the
More informationM-Tuned reroute kit XX
M-Tuned reroute kit 14-161XX Manufactured and designed by: *Professional Installation Recommended but not required 1) Disconnect the negative terminal from the battery in the trunk. 2) Drain the coolant
More informationDiag. Code 14, 15 Ignition Signal Circuit
TR26 EINE TROUBLESHOOTI Diag. Code 14, 15 Ignition Signal Circuit CIRCUIT DESCRIPTION The ECU determines the ignition timing, turns on Tr1 at a predetermined angle ( CA) before the desired ignition timing
More informationDisconnect the battery power from the car.
Adding a safety fuse to the ignition circuit of 1956 to 1962 Corvettes Part 1 is for 1958 to 1962. Part 2 is for 1956 to 1957 Rich Mozzetta and Dave Zuberer Part 1-1958 to 1962 Here is a way to add a fuse
More informationInstallation Instructions for the Plug & Play Remote Start Package (EVOCHR4)
T6002 v1.1 02/2013 Installation Instructions for the Plug & Play Remote Start Package (EVOCHR4) For CHRYSLER Town & Country 2008-2012 Review the remote start installation manual for safety instructions!
More informationRostra Electronic Cruise Control Install On a Stratoliner or Roadliner
Rostra Electronic Cruise Control Install On a Stratoliner or Roadliner MATERIALS LIST: 1 - Rostra Part # 250-1223 (www.brandondist.com/products/cruise1223.htm) 1 - Signal Splitter part # 250-4369 1 - Engagement
More informationTriumph Street Triple VSM Grip Heater Install
Triumph Street Triple VSM Grip Heater Install Introduction: With winter fast approaching and with painful memories of last winter riding with the club it was time to do something about getting some grip
More informationContacts The moveable contact, which is the one affected by the armature is sometimes referred to as the hinge contact.
Relays & Wiring 101 Basically, a relay is an electrically operated, remotely controlled switch. A simple electromagnetic relay is an adaptation of an electromagnet. It consists of a coil of wire surrounding
More informationInstallation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013
Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader
More informationTo Install the Jolley magnetic electronic ignition system and new matched coil and resistor in Daimler Ferret.
To Install the Jolley magnetic electronic ignition system and new matched coil and resistor in Daimler Ferret. Ignition system parts purchased from Frank Jolley www.classicheads.com First problem is to
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationPrins autogassystemen b.v. Veldhoven
Prins autogassystemen b.v. Veldhoven MOUNTING INSTRUCTION ENGINE CONVERSION SET MAKE OF AUTOMOBILE: TYPE: ASTRA PISTON DISPLACEMENT: 2000 cc MT NUMBER OF VALVES: 16V ENGINE NUMBER: X20XEV INJECTION SYSTEM:
More informationHKS ELECTRONICS TECHNOLOGY SLD T6 HKS SPEED LIMIT DEFENCER
HKS ELECTRONICS TECHNOLOGY SLD T6 HKS SPEED LIMIT DEFENCER INSTRUCTIONS Pursuing the Ultimate in Engine Performance and Efficiency HKS Company Limited 212290 047T 18 th Oct 2000 Ver. 3-1. 02 Introduction
More informationASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds
ASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds Description: Very easy to build, The FK109 Led Flasher kit makes the perfect
More informationG - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.
More informationMODULE TEST UNIT. Part No: MTU-12 V2.1
MODULE TEST UNIT Part No: MTU-12 WHITE YEL ORANGE VEHICLE RED 150 Fused + 12 Volt BLACK 150 RED + 12 Volt Out BLACK Out WHITE Pulse ( adjustable by pot) Left High LED will light over 4.5 V Left Low LED
More informationMain Relay. Fixing your PGM-Fi Main Relay.
Main Relay Fixing your PGM-Fi Main Relay. Symptoms Problems starting the car, usually after a short run (when the interior is warm), though in bad cases the car may fail to start at any time. A classic
More informationInstallation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14
Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14 Thank you for purchasing your remote start from MyPushcart.com - an industry
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationTip: LED Lighting Improvements for Rheingold Set Date:
Hi All, Recently I came into possession of the 41928 Rheingold set and was excited to see that I could add a function decoder to switch the light functions on and off. The first problem is Märklin don
More informationOVERLOAD PROTECTION. All electrical circuits must have some means of protecting against overload.
AN OVERLOAD PROTECTION CIRCUIT FOR AN INVERTER OR AN ELECTRIC FUSE FOR THE A.C. MAINS SUPPLY WITH A RESET BUTTON. PROJECT NO. 103 BY OPIYO LYDIA ACHIENG EXAMINER : PROF. M.K. MANG OLI SUPERVISOR: DR. C.
More informationInstalling Ignition Coil relay
Installing Ignition Coil relay Above is a schematic diagram of the coil relay modification. All it really does is, it uses the existing 12 Volt positive that normally powers the coils, to power a relay,
More informationIntroduction. Open Loop vs. Closed Loop. The Purpose of an O 2 Sensor Clamp
Introduction This O 2 sensor clamp is designed for use with the Greddy emanage Ultimate engine control system. While these instructions are specific to the Mazda MX-5 Miata, the clamp will work on any
More informationQUASAR ELECTRONICS KIT No ELECTRONIC CAR IGNITION
QUASAR ELECTRONICS KIT No. 1058 ELECTRONIC CAR IGNITION General Description The advantages of having an electronic ignition in your car are well known. Let us mention them again: 1. Perfect burning of
More informationHow to Make a Solid State Instrument Voltage Regulator
Taken from the web page: http://chris66dad.tripod.com/id29.html How to Make a Solid State Instrument Voltage Regulator Note: Although this description was intended for a Ford Mustang, it also works for
More informationMegasquirt II with V3.0 PCB Stock Rotary CAS Setting up your 2 rotor engine to use a stock unmodified Mazda Crank Angle Sensor with Megasquirt
Megasquirt II with V3.0 PCB Stock Rotary CAS Last Updated: 2/November/2007 Setting up your 2 rotor engine to use a stock unmodified Mazda Crank Angle Sensor with Megasquirt Read through all of the steps
More informationV8 Gen. V Ford Mustang 2010 Update
V8 Gen. V Ford Mustang 2010 Update There were several updates to the Ford Mustang in the 2010 model year. This document outlines the differences between the installation steps necessary for the 2010 Mustang
More informationFitment Guide Volkswagen Golf GTI MK V1.0
Fitment Guide Volkswagen Golf GTI MK6 2010 V1.0 www.ecliptech.com.au You need 3 wires to fit the Shift-I to the GTI. Power and Ground from the diagnostics port (near driver s side knee) and the RPM signal
More informationWalthers/Life-Like USRA Steam Locomotive
North Raleigh Model Railroad Club Installing Decoders in N Scale Locomotives Detailed Instructions Walthers/Life-Like USRA 2-8-8-2 Steam Locomotive by David Derway May 17, 2010 Table of Contents Introduction...
More informationDTC 14 Ignition Signal Circuit
EG672 ENGINE DTC 14 Ignition Signal Circuit CIRCUIT DESCRIPTION The ECM determines the ignition timing, turns on Tr 1 at a predetermined angle ( CA) before the desired ignition timing and outputs an ignition
More informationMAKE OF AUTOMOBILE: MODEL YEAR: 2007 SYSTEM APPROVAL NUMBER ( R115 ) VSI-LPG 10 ENGINE SET NUMBER 364/
MAKE OF AUTOMOBILE: TYPE: FABIA PISTON DISPLACEMENT: 1400 NUMBER OF VALVES: 16 ENGINE NUMBER: BUD TRANSMISSION TYPE ( MT / AT ) MT VEHICLE CATEGORIES M or N M TYPE VSI INJECTOR ( NUMBER + COLOR ) 180/30410
More information470nF REG1 LM2940. VR3 100k 10k VR1 100 F. 470pF. 100nF. 100nF RELUCTOR Q2 BC k. 10k TP GND. 2.2nF TO RELUCTOR. 470nF REG1 LM2940 REG1 LM2940
Where to buy kits Jaycar and Altronics have full kits (including the case) available for the High Energy Electronic Ignition System. The Jaycar kit is Cat. KC-5513 while the Altronics kit is Cat. K4030
More informationGENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................................. 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION
More informationInstallation Tips for your Excalibur Remote Start (for Honda and Acura Vehicles) rev 11/28/2012
Installation Tips for your Excalibur Remote Start (for Honda and Acura Vehicles) rev 11/28/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationGENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................... 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION FOR DIAGNOSIS.......
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationFeature Description. Version History
TA2 Malfunction Indicator Lamp (MIL) and Engine Protection Document Number: FD-0007 Author: J. Goodloe Version: 03 Publish Date: 2016-03-18 Feature Description Version History Version Date Modified Sections
More informationBill of Materials: Spinning top brushless DC motor PART NO
Spinning top brushless DC motor PART NO. 2171006 The heart of this kit consists of a bifilar wound coil driven with two NPN transistors. While the circuit is easy, the coil will be tedious to wind since
More informationBMW 2002 M42 Swap Notes-THIS IS NOT FINISHED
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED This document is to help those that want to install an m42 into a BMW 2002. It is based around an e30 engine, trans, and wiring. You can use the e36 block/head/wiring
More informationJB1 and JB4 Install Guide for VAG EA888 Gen 3 engines 252hp version
JB1 and JB4 Install Guide for VAG EA888 Gen 3 engines 252hp version Use subject to terms and conditions posted at http://www.burgertuning.com/terms.htm THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING
More information(905)
(905)953-9260 Marc@M-Tuned.com Coolant Reroute Kit *Professional Installation Recommended but not required 1) Disconnect Negative Terminal from Battery in trunk. 2) Drain Coolant from your cooling system.
More informationM-TUNED COOLANT RE-ROUTE KIT
M-TUNED COOLANT RE-ROUTE KIT Part # MC-RR-216, MC-RR-218 Applications: 90-93 Miata 1.6L B6 94-97 Miata 1.8L BP More detailed instructions: http://www.etdracing.com/m-tuned/reroute.pdf 1) Disconnect Negative
More informationLED Flasher. R1 R2 100 F + C1 100 F +
LED Flasher. Specification Operates from a 6-12V supply. Alternately flashes two LEDs. Flash rate adjustable by changing the capacitor values and the 10k resistor values. Circuit Diagram 9V LED1 470 TR1
More informationTo avoid a short cut please file off the right half of the Y-hole flange.
Fitting instructions for automatic alternator controller for Moto Guzzi with Bosch alternator 1. alternator modification - 2. Fitting - 3. adjustment (ignition only) First remove the connector block of
More informationWater Temperature. GM LS Engine Gauges Installation Guide
2650-1563-00 GM LS Engine Gauges Installation Guide Water Temperature For water temperature, there is a port located on the right side (passenger side) of the engine, in the cylinder head, past the last
More informationBe sure to read item #4 or you will very likely damage something.
Installation Instructions for 82513 Reverse Lock Out Module Magnum, TR6060 or T56 6-Speed Be sure to read item #4 or you will very likely damage something. How It Works The electronic module contains a
More informationKawasaki Vulcan 1500 Classic
Floppy Disc Request Form If you do not have a CD-Rom drive and would like to receive the program and the alternate maps for your model on a 3 1/2 floppy disc, please fax this form to Dynojet at 1-702-399-1431
More informationFog Light setup for a 2003 XL F250 Super Duty using the OEM kit.
Fog Light setup for a 2003 XL F250 Super Duty using the 2005-2007 OEM kit. Since the kit (1C3Z15200BB) for the 2001-2004 series truck was not available anymore, I explored options to put a set of OEM fog
More informationJB1 for VAG EA888 Gen 3 engines Install Guide Last Updated: /201
JB1 for VAG EA888 Gen 3 engines Install Guide Last Updated: /201 Use subject to terms and conditions posted at http://www.burgertuning.com/terms.htm THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING
More informationInstallation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles)
Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to doit-yourself
More informationInstallation Tips for your Remote Start system (for Toyota Camry & Prius C, ) Crimestopper RS0+ EVO-ALL T3468 rev#1.
Installation Tips for your Remote Start system (for Toyota Camry & Prius C, 2012-2014) Crimestopper RS0+ EVO-ALL T3468 rev#1.1 1/22/2015 Thank you for purchasing your remote start from MyPushcart.com -
More informationAtlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes
Atlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an Atlas Silver
More informationIdle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana
Introduction An ISO 9001:2015 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2019 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications The A-ITC620-A1 is an
More informationThis year Märklin have released a coach which has included LED lighting with a currentconducting close coupler (single pole)
Hi All, Over the past few months I have been working at a steady pace to install LED lighting in my passenger coaches. The coach lighting must have LED lights to reduce power consumption on the layout
More informationMFI Pro - Instructional Manual (Toyota 1uzfe) Version 06.01
Tel: 011 3971953 - Fax: 011 3978197 - info@gotech.co.za www.got e ch.c o.za MFI Pro - Instructional Manual (Toyota 1uzfe) Version 06.01 Index: Introduction 1 Before You Begin 1 Basic Tools Required 2 Basic
More informationTechnical Sheet on Sprint Tachometers and MSD Ignition Systems. How to Install a Sprint Tachometer With a MSD 6A Ignition System
Technical Sheet on Sprint Tachometers and MSD Ignition Systems How to Install a Sprint Tachometer With a MSD 6A Ignition System Step 1: Wiring Procedures Sprint Tachometers are voltage-triggered tachometers
More informationModifying the exterior lighting of the Ram truck
Modifying the exterior lighting of the Ram truck The Ram truck has been designed and developed using standard incandescent lights. These lights are controlled by a computerized module called the Central
More informationATASA 5 th. ATASA 5 TH Study Guide Chapter 27 Pages Ignition Systems 68 Points. Please Read the Summary
ATASA 5 TH Study Guide Chapter 27 Pages 810 835 68 Points Please Read the Summary Before We Begin Keeping in mind the Career Cluster of Transportation, Distribution & Logistics Ask yourself: What careers
More informationAugust Alfa Giulia Forza Exhaust Controller Installation
August 2018 Alfa Giulia Forza Exhaust Controller Installation Forza Controller kit contents Forza Model B3A or Model E Controller (B3A is shown) Single electrical connector Special configuration Always
More informationDARK ACTIVATED COLOUR CHANGING NIGHT LIGHT KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE SOOTHING LIGHTING EFFECTS WITH THIS DARK ACTIVATED COLOUR CHANGING NIGHT LIGHT KIT
More informationTD5 BOOSTER INSTALLATION GUIDE
TD5 BOOSTER INSTALLATION GUIDE SAFETY NOTICE: Please ensure that you have removed the ignition key, and that you have it on you whilst fitting this device! Although this guide shows fitting instructions
More informationMFI Pro - Instructional Manual Version 05.01
58 Graniet Street, Jet Park, JHB - Tel: 0 397953 - Fax: 0 397897 www.got e ch.c o.za MFI Pro - Instructional Manual Version 05.0 Index: Introduction Before You Begin Basic Tools Required 2 Basic Components
More informationMGB V8 Roadster restoration project Report 128
20th March 2017. Sorry to keep you in suspenders between report 127 and report 128, with regards to the indicator stalk switch. INDICATOR & HORN STALK SWITCH - continued After removing all the internal
More informationIdle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana
An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2018 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications Introduction The A-ITC620-A1 is an
More informationInstallation Instructions for the Plug & Play Remote Start Package (EVOCHR5)
T6018 v1.1 02/2013 Installation Instructions for the Plug & Play Remote Start Package (EVOCHR5) For DODGE Nitro 2007-2011 Review the remote start installation manual for safety instructions! Overview Your
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1970-74 Cuda/Challenger FOR PART NUMBER S: 1620810010, 1620810020, 1620810051, 1620820010, 1620820020, 1620820051 S I NCE 1986 Instruction # 8000000005
More informationSUPER CAPACITOR CHARGE CONTROLLER KIT
TEACHING RESOURCES ABOUT THE CIRCUIT COMPONENT FACTSHEETS HOW TO SOLDER GUIDE POWER YOUR PROJECT WITH THIS SUPER CAPACITOR CHARGE CONTROLLER KIT Version 2.0 Teaching Resources Index of Sheets TEACHING
More informationCHAPTER 2. Current and Voltage
CHAPTER 2 Current and Voltage The primary objective of this laboratory exercise is to familiarize the reader with two common laboratory instruments that will be used throughout the rest of this text. In
More informationMAKE OF AUTOMOBILE: 316 / 318i E46 NUMBER OF VALVES:
MAKE OF AUTOMOBILE: TYPE: 316 / 318i E46 PISTON DISPLACEMENT: 1800 2000 cc NUMBER OF VALVES: 16V ENGINE NUMBER: N42B18A / N42B20A TRANSMISSION TYPE ( MT / AT ) MT VEHICLE CATEGORIES M or N M TYPE VSI INJECTOR
More informationHasse Mods for the Ampeg J20 Guitar Amp
Hasse Mods for the Ampeg J20 Guitar Amp The following is adapted from a post I put up on The Gear Page, in the Amp Techincal forum. It shows the mods I did to my Ampeg J20. Okay, here s my mods for this
More informationKawasaki Nomad
Floppy Disc Request Form If you do not have a CD-Rom drive and would like to receive the program and the alternate maps for your model on a 3 1/2 floppy disc, please fax this form to Dynojet at 1-702-399-1431
More informationMAKE OF AUTOMOBILE: PISTON DISPLACEMENT: 8300 NUMBER OF VALVES: 20 TRANSMISSION TYPE ( MT / AT ) TYPE VSI INJECTOR (COLOR ) VERSION ( LPG / CNG )
MAKE OF AUTOMOBILE: TYPE: PISTON DISPLACEMENT: 8300 NUMBER OF VALVES: 20 ENGINE NUMBER: SRT V10 Viper TRANSMISSION TYPE ( MT / AT ) AT TYPE VSI INJECTOR (COLOR ) YELLOW VERSION ( LPG / CNG ) LPG INJECTION
More informationCannondale Diagnostic Tool Manual
Cannondale Diagnostic Tool Manual For vehicles (ATV & Motorcycles) equipped with the MC1000 Engine Management System Software CD P/N 971-5001983 Data Cable P/N 971-5001984 POTENTIAL HAZARD Running the
More informationMotronic September 1998
The Motronic 1.8 engine management system was introduced with the 1992 Volvo 960. The primary difference between this Motronic system and the previous generation of Volvo LH-Jetronic engine management
More informationBASIC ELECTRICAL MEASUREMENTS By David Navone
BASIC ELECTRICAL MEASUREMENTS By David Navone Just about every component designed to operate in an automobile was designed to run on a nominal 12 volts. When this voltage, V, is applied across a resistance,
More informationInstallation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012
Installation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing
More information12-Volt Negative Ground Installation Instructions
12-Volt Negative Ground Installation Instructions For Part Number: 1183 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for 12-Volt negative
More informationIn the first part of this series on
by Mike Van Dyke In the first part of this series on diagnosing ECUs, we went over some basic visual diagnosis of common failures. In this, the second part of the series, we re going to go over some basic
More informationRemote Start Kit for GM Installation RS1/3/4/7 + ADS-DL Tip Sheet
Remote Start Kit for GM Installation RS1/3/4/7 + ADS-DL Tip Sheet rev 1.4 12/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to do-it-yourself
More informationMaxxECU quickstart guide ( )
Be a tuning mastermind. Like us. MaxxECU quickstart guide (2019-02-01) Online help! maxxecu.com/support Wiring diagrams Installation help Pinout Support maxxecu.com/support Legal disclaimer All performance
More informationInstallation Instructions for: EMS P/N Toyota Supra
Installation Instructions for: EMS P/N 30-1130 1989-1992 Toyota Supra! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS System
More informationF - BASIC TESTING Toyota Celica INTRODUCTION PRELIMINARY INSPECTION & ADJUSTMENTS VISUAL INSPECTION MECHANICAL INSPECTION
F - BASIC TESTING 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 4-Cylinder Basic Diagnostic Procedures Celica INTRODUCTION The following diagnostic steps will help prevent overlooking a simple problem.
More informationED COPYRIGHT PROTECTE
Tremec T56 / Magnum / TR-6060 Reverse Lockout Control Module Installation Instructions ***Make sure you read item #4 on next page (page 2) or you will very likely damage something. How It Works The electronic
More informationTHE BATTERY CHARGER OF RON PUGH
THE BATTERY CHARGER OF RON PUGH THANKS IS DUE TO RON PUGH WHO HAS KINDLY SHARED THE CONSTRUCTION DETAILS OF HIS VERY SUCCESSFUL BATTERY CHARGER WHICH IS COP=13 WHEN OPERATING AT 24 VOLTS. IF YOU DECIDE
More informationUNIVERSAL GAUGE WIRE HARNESS
2650-1797-00 UNIVERSAL GAUGE WIRE HARNESS For Installing Auto Meter Electric Speedometer, Tachometer, And Short Sweep Electric Oil Pressure, Water Temperature, Fuel Level, and Volt Meter Gauges. This harness
More informationCANBUS Emulator Mini V1.x. Overview - Installation and Operating Instructions
CANBUS Emulator Mini V1.x Overview - Installation and Operating Instructions Contents Overview... 2 Installation... 3 Basic Install... 3 With optional speed sensor input and reverse signal input... 3 Operation...
More informationRepairing a Loose Headlight Reflector Volvo V70XC ? Mark Pilant
Repairing a Loose Headlight Reflector Volvo V70XC 2001 200? Mark Pilant If you find yourself in a position where the headlight adjusters do not change the aiming of your headlight, it is possible one of
More informationKORG KR-55. µsync installation guide version 1.0, 14 October
KORG KR-55 µsync installation guide version 1.0, 14 October 2016 www.artefacts.nl Introduction The Korg KR-55 or KR-55b has no standard din sync input. Artefacts developed a piece of hardware to convert
More informationInstallation Directions for FINGER STICK and Blocker Plate
Installation Directions for FINGER STICK and Blocker Plate What is a Finger Stick? A Finger Stick is a simple circuit that modifies the MAF signal on LLY and LBZ engines (not LB7 engines) to expected levels
More informationALTERNATOR - HITACHI
ALTERNATOR - HITACHI 1986 Isuzu Trooper II 1986 Alternators & Regulators HITACHI ALTERNATORS Isuzu DESCRIPTION Hitachi alternators are conventional 3-phase, self-rectifying alternators. Three positive
More information