Protector XL Floor-Mounted Laboratory Hoods Features & Benefits

Transcription

1 Protector XL FLOOR-MOUNTED LAORATORY HOODS

2 Protector XL Floor-Mounted Laboratory Hoods Features & enefits Protector XL Floor-Mounted Laboratory Hoods accommodate laboratory procedures that require over-sized equipment or maximum work area. Users with applications requiring distillation racks, extraction apparatus or large drums and carboys benefit from the increased height these hoods provide. Protector XL Floor-Mounted Laboratory Hoods are supplied in three depths and several widths up to 16 feet. Depending on the model, these hoods have vertical-rising or horizontal-sliding sashes. Front and side panels may be easily removed for lamp replacement and access to electrical supply connections. ETL-listed. Hoods carry the ETL mark signifying that they are certified to UL / , UL 1805 and AN/SA 22.2 No Durable and attractive exterior is glacier white, dry powder epoxycoated steel. Tempered safety glass sashes are anti-racking for smooth operation. Hoods feature either vertical-rising or horizontal-sliding sashes depending on hood model. When fully open, vertical-rising sashes do not extend above the hood. Adjustable baffles provide a uniform face velocity pattern across the sash opening of the hood. Fluorescent lighting illuminates the interior. The high-efficiency, instant start, T8 fluorescent lights are located outside the hood interior for corrosion-resistance and easy replacement. ontact Labconco for ordering information on explosionproof lighting. Pre-wired electrical components. Fluorescent lights and switches are factory-wired to the hood s single point junction box. One electrical duplex receptacle is factory-wired on fixtured models. Each hood is factoryprepared for up to four electrical duplexes and an airflow monitor. Interior working dimensions are offered in standard and larger depths. Working depths include 30", 36" and 48". Performance tested to ASHRAE y-pass airflow design ensures relatively stable face velocities. olor-coded service fixtures for gas, air, water, vacuum and other services have remote controls for use regardless of the sash position. Two service fixtures are pre-plumbed on fixtured models. Each hood is factory prepared for up to eight service fixtures (four on each side). Service access panels allow easy accessibility to plumbing from the front and inside of the hood. hemical-resistant, fiberglassreinforced composite panel liner surpasses all national codes for flame spread and has a bright white surface for excellent light reflectivity. 2

3 Protector XL Floor-Mounted Laboratory Hoods 6' Protector XL Floor-Mounted Laboratory Hood lower and ductwork must be ordered separately. Fixtured models feature: Two pre-plumbed service fixtures with forged brass valves, lower right side with brass tubing for gas and lower left side with copper tubing for cold water. omponents for converting either or both fixtures to air and vacuum are provided. Inlet tubing is not provided. One pre-wired 115 volt, 20 amp electrical duplex receptacle on lower right side. Requires Ductwork and lower 8' Protector XL Floor-Mounted Laboratory Hood lower and ductwork must be ordered separately. All models require (not included): Remote lower. Request lowers ooklet. Ductwork. Request lowers ooklet. All models feature: y-pass airflow design. Glacier white, dry powder epoxy-coated steel exterior. hemical-resistant, fiberglass-reinforced composite panel liner and adjustable upper and lower baffles with flame spread less than 25 per ASTM E-84. Removable front and side panels and exterior and interior service access panels for access to plumbing and electrical wiring. Pre-wired T8 fluorescent lighting, light and blower switches for 115 volt, 60 Hz operation. Shipped in multiple sections: top, bottom and sashes. Epoxy-coated stainless steel, 12.81" ID exhaust connection(s). 4', 5', 6' and 8' models feature: Two 3/16" thick tempered safety glass vertical-rising sashes framed with PV (4', 5' and 6' models) or epoxy-coated aluminum (8' models). Sashes do not extend above the hood when fully open. 8', 10', 12' and 16' models feature: Four 3/16" thick tempered safety glass horizontal-sliding sashes with epoxycoated aluminum frames and sash tracks. All models conform to the following regulations and standards: SEFA NFPA ASTM E84-09 ASHRAE ANSI Z UL / AN/SA 22.2 No UL 1805 Optional accessories for on-site installation include: Service Fixture Kits. See page 7. Side-Mount Oval upsink. See back cover. Electrical Duplex Kits. See back cover. Guardian Airflow Monitor Kits. See back cover. ontact Labconco at or for ordering information on ceiling enclosure and rear finish panel kits, fire extinguishers, explosion-proof lighting, solid epoxy floors, tissue screens and distillation grids; and for blower sizing assistance. Heights of switches, electrical receptacle and service fixtures meet requirements of ADA. 3

4 Ordering Information 4', 5', 6' and 8' Protector XL Floor-Mounted Laboratory Hoods with vertical-rising sashes Exterior Interior 12.81" (32.5 cm) Shipping Nominal atalog Depth (A) Depth () ID Exhaust Fluorescent Service Electrical Weight Width Number inches/cm inches/cm ollar(s) Lamps Fixtures Duplex lbs./kg 4 Feet / / ea. 25 watt / / / ea. 25 watt / / / ea. 25 watt /338 5 Feet / / ea. 32 watt / / / ea. 32 watt / / / ea. 32 watt /390 6 Feet / / ea. 32 watt / / / ea. 32 watt / / / ea. 32 watt /447 8 Feet / / ea. 25 watt / / / ea. 25 watt / / / ea. 25 watt /556 Nominal Total Exhaust FM and Static Pressure with sashes 50% open Width 100 fpm S.P. 80 fpm S.P. 4 Feet " " 5 Feet " " 6 Feet " " 8 Feet " " Ordering Information 8', 10', 12' and 16' Protector XL Floor-Mounted Laboratory Hoods with horizontal-sliding sashes Exterior Interior 12.81" (32.5 cm) Shipping Nominal atalog Depth (A) Depth () ID Exhaust Fluorescent Service Electrical Weight Width Number inches/cm inches/cm ollar(s) Lamps Fixtures Duplex lbs./kg 8 Feet / / ea. 25 watt / / / ea. 25 watt / / / ea. 25 watt / Feet / / ea. 32 watt / / / ea. 32 watt / / / ea. 32 watt / Feet / / ea. 32 watt / / / ea. 32 watt / / / ea. 32 watt / Feet / / ea. 25 watt / / / ea. 25 watt / / / ea. 25 watt /966 Nominal Sashes Total Exhaust FM and Static Pressure Width Open 100 fpm S.P. 80 fpm S.P. 8 Feet " " 10 Feet " " 12 Feet " " 16 Feet " 4

5 Dimensional Data 4', 5', 6' and 8' Protector XL Floor-Mounted Laboratory Hoods with vertical-rising sashes 4.91" (12.5 cm) 2.27" (5.8 cm) 4.91" 2.27" 12.81" ID Exhaust ollar TOP 4', 5', 6' 2.50" (6.4 cm) dia. Service Fixture Supply Holes F 12.81" (32.5 cm) ID Exhaust ollars TOP (8') 10.53" 2.50" dia. Service Fixture Supply Holes E Single Point Internal Junction ox 10.53" (26.7 cm) D Single Point Internal Junction ox A* * * D* E* F* H* 4' Hood (121.9) (97.2) (61.0) (99.6) (76.2) (149.4) (121.9) (97.2) (61.0) (114.8) (91.4) (149.4) (121.9) (97.2) (61.0) (145.3) (121.9) (149.4) 5' Hood (152.4) (127.6) (76.2) (99.6) (76.2) (149.4) (152.4) (127.6) (76.2) (114.8) (91.4) (149.4) (152.4) (127.6) (76.2) (145.3) (121.9) (149.4) 6' Hood (182.9) (158.1) (91.4) (99.6) (76.2) (149.4) (182.9) (158.1) (91.4) (114.8) (91.4) ( (182.9) (158.1) (91.4) (145.3) (121.9) (149.4) 8' Hood (243.8) (219.1) (61.0) (99.6) (76.2) (121.9) (149.9) (243.8) (219.1) (61.0) (114.8) (91.4) (121.9) (149.9) (243.8) (219.1) (61.0) (145.3) (121.9) (121.9) (149.9) *Inches (centimeters) A D Fluorescent Lights 4.19" (10.6 cm) 68.15" (173.1 cm) Viewing Height to Floor H Sash Opening Front Access Panel (one on each side) Service Fixture (one on each side) 115 Volt, 20 Amp Duplex Electrical Receptacle 2.00" (5.1 cm) Interior Access Panels 15.00" (38.1 cm) Upper abinet Lower ase E 36.00" 77.00" (195.6 cm) 84.00" (213.4 cm) 7.00" (17.8 cm) 95.00" (241.3 cm) Sash Frame to affle FRONT 2.50" (6.4 cm) dia. Ser Service Fixture Supply Holes SIDE ontact Labconco at or or visit for detailed AutoAD drawings. 5

6 Dimensional Data 8', 10', 12' and 16' Protector XL Floor-Mounted Laboratory Hoods with horizontal-sliding sashes A* * * D* E* F* G* H* 8' Hood (243.8) (219.1) (61.0) (99.6) (76.2) (121.9) (57.2) (109.9) (243.8) (219.1) (61.0) (114.8) (91.4) (121.9) (57.2) (109.9) (243.8) (219.1) (61.0) (145.3) (121.9) (121.9) (57.2) (109.9) 4.91" (12.5 cm) 2.27" (5.8 cm) 2.50" (6.4 cm) dia. Service Fixture Supply Holes F 12.81" (32.5 cm) ID Exhaust ollars TOP 8', 10', 12' 10.53" (26.7 cm) D Single Point Internal Junction ox 10' Hood (304.8) (280.0) (88.9) (99.6) (76.2) (127.0) (72.4) (140.3) (304.8) (280.0) (88.9) (114.8) (91.4) (127.0) (72.4) (140.3) (304.8) (280.0) (88.9) (145.3) (121.9) (127.0) (72.4) (140.3) 12' Hood (365.8) (341.0) (104.1) (99.6) (76.2) (157.5) (87.6) (170.8) (365.8) (341.0) (104.1) (114.8) (91.4) (157.5) (87.6) (170.8) (365.8) (341.0) (104.1) (145.3) (121.9) (157.5) (87.6) (170.8) 16' Hood (487.7) (462.9) (61.0) (99.6) (76.2) (121.9) (118.1) (231.8) (487.7) (462.9) (61.0) (114.8) (91.4) (121.9) (118.1) (231.8) (487.7) (462.9) (61.0) (145.3) (121.9) (121.9) (118.1) (231.8) *Inches (centimeters) Four ollars 4.91" (12.5 cm) 2.27" (5.8 cm) F 12.81" (32.5 cm) ID Exhaust ollars 2.50" (6.4 cm) dia. Service Fixture Supply Holes F 12.81" (32.5 cm) ID Exhaust ollars 10.53" (26.7 cm) D Single Point Internal Junction ox TOP (16') A Fluorescent Lights D 4.19" (10.6 cm) Front Access Panel (one on each side) 15.00" 7.00" (17.8 cm) 68.15" (173.1 cm) Viewing Height to Floor H Max Opening G Door Width Service Fixture (one on each side) 115 Volt, 20 Amp Duplex Electrical Receptacle 2.00" (5.1 cm) Interior Access Panels Upper abinet Lower ase E 77.00" (195.6 cm) 36.00" (91.4 cm) 84.00" (213.4 cm) 95.00" (241.3 cm) Sash Frame to affle FRONT SIDE ontact Labconco at or or visit for detailed AutoAD drawings. 6

7 Accessories Standard Service Fixture Kits For mounting on the left or right side of the Protector XL Floor-Mounted Laboratory Hood. Each kit includes one remotely-controlled service fixture with valve and 0.25" diameter tubing, color-coded fixture knob and color-coded hose connector. Inlet tubing is not included. Shipping weight 4 lbs. (1.8 kg) atalog # Kit Tubing Valve Knob/onnector Max. Max. Working olor Flow Rate Pressure ** old Water (W) opper rass Green 3.5 GPM (13.2 LPM) 40 psi Air (AIR) opper rass Orange 23.7 FM 40 psi Vacuum (VA) opper rass Yellow 8.6 FM 14.7 psi Gas (GAS) rass rass lue 29.0 FM (441 TU/sec) 40 psi Argon (ARG) opper rass Gray 20.2 FM 40 psi Hot Water (HW) opper rass Red 3.5 GPM (13.2 LPM) 40 psi Deionized/ Stainless Nickel-Plated & White 3.5 GPM (13.2 LPM) 40 psi Distilled Water (DI) Steel Stainless Steel Steam (STM) opper rass lack 0.5 LM/min 40 psi Nitrogen (NIT) opper rass rown 24.1 FM 40 psi * Oxygen (OXY) opper rass with Light Green 22.6 FM 40 psi Oxygen- ompatible Lubricant old Water Gooseneck Fixture Kits For mounting on the left or right side of any Protector XL Floor-Mounted Laboratory Hood with 30" interior depth. Each kit includes one remotely-controlled gooseneck with brass valve and 0.375" diameter copper tubing and green fixture knob. Inlet tubing is not included. ontact Labconco for ordering information on Gooseneck Fixture Kits for Protector Hoods with interior depths of 36" or 48". Shipping Weight 10 lbs. (4.5 kg) atalog # Kit Description Max. Flow Rate Max. Working Pressure ** old Water (W) For Hoods with Interior 3.5 GPM (13.2 LPM) 40 psi Gooseneck Depths of 24" to 30". Includes green epoxy-coated brass rigid/swivel gooseneck. Hot and old Water Mixing Gooseneck Fixture Kit For any Protector XL Floor-Mounted Laboratory Hood with interior depth of 24" to 30". Each kit includes one remotelycontrolled, white epoxy-coated, brass rigid/swivel gooseneck with brass valve and 0.25" diameter copper tubing, one green fixture knob and one red fixture knob. Inlet tubing is not included. ontact Labconco for ordering information on Gooseneck Fixture Kits for Protector Hoods with interior depths of 36" or 48". Shipping weight 11 lbs. (5.0 kg) atalog # Kit Description Max. Flow Rate Max. Working Pressure ** Hot (HW) and old Water (W) For Hoods with Interior 3.5 GPM (13.2 LPM) 40 psi Mixing Gooseneck Depths of 24" to 30" Deionized/Distilled Water Gooseneck Fixture Kit For mounting on the left or right side of any Protector XL Floor-Mounted Laboratory Hood with 30" interior depth. Each kit includes one remotely-controlled, gray PV rigid gooseneck with stainless steel valve and 0.25" diameter tubing and white fixture knob. ontact Labconco for ordering information on Gooseneck Fixture Kits for Protector Hoods with interior depths of 36" or 48". Inlet tubing is not included. Shipping weight 10 lbs. (4.5 kg) atalog # Kit Description Max. Flow Rate Max. Working Pressure ** Deionized/Distilled Water For Hoods with Interior 3.5 GPM (13.2 LPM) 40 psi (DW) Gooseneck Depths of 24" to 30" GPM=gallons per minute LPM=liters per minute FM=cubic feet per minute TU/sec=ritish thermal unit per second LM/min= pounds mass per minute *WaterSaver **Maximum allowable pressure is 200 psi with a working pressure of 40 psi. Requires 1.375" dia. drill hole in liner. 7

8 Accessories Side-Mount Oval Polypropylene upsink Mounts on side wall of Protector XL Floor-Mounted Hoods. 6" x 3" cupsink. 1.5" NPSM thread. Requires a 1.875" diameter drilled hole in liner. Shipping weight 4 lbs. (1.8 kg) National Pipe Straight Mechanical Duplex Electrical Receptacle Kits For mounting in left or right side of any 4', 5', 6', 7' or 8' Protector XL Floor-Mounted Laboratory Hood. Each kit includes duplex electrical receptacle, wiring, junction box and receptacle cover plate. ontact Labconco for ordering information on Duplex Electrical Receptacle Kits for Protector Hoods with widths of 10', 12' or 16'. atalog # Kit For Hood with exterior widths: Shipping Wt. lbs./kg volts, 20 amps A 4', 5', 6' and 8' 4/ volts, 20 amps A, GFI 4', 5', 6' and 8' 4/ volts, 20 amps A 4', 5', 6' and 8' 4/1.8 Guardian 1000 Digital Airflow Monitor Kits Monitor and alert the operator to low airflow conditions. Include face plate with circuit board, electrical power pack, airflow hose and flow hose adapter. LD displays actual airflow in fpm or m/sec from 0 to 999 fpm (0 to 5.0 m/s). Audible/visual alarm alerts user to sustained low velocity condition. alibration instructions displayed on LD. LED lights display red for alarm, yellow for caution, green for normal. Include temperature-compensated sensor, external alarm, night setback and alarm mute functions. UL and E listed. For installation in a factory-prepared cutout on upper portion of right fixture panel. ontact Labconco for ordering information on an optional factory-prepared RS-485 port for Modbus RTU communication. atalog # Description For use with: Shipping Wt. lbs./kg volts, 60 Hz Protector XL Floor-Mounted Laboratory Hood 6/ * 230 volts, 50 Hz Protector XL Floor-Mounted Laboratory Hood 6/2.7 Guardian 500 Airflow Monitor Kits Monitor and alert the operator to low airflow conditions. Include face plate with circuit board, electrical power pack, vinyl tubing and airflow tube adapter. From the monitor s face plate, the user can easily select and calibrate a setpoint between 30 and 250 fpm using a velocity meter and a screwdriver. A green LED glows to indicate safe when airflow is greater than the low setpoint. A red LED flashes to indicate low when airflow is below the low setpoint. An amber LED flashes when the sash is raised above the maximum safe working opening. An audible alarm sounds (and can be muted) when under low and sash high conditions. Include night setback, external alarm and alarm mute functions. For installation in a factory-prepared cutout on upper portion of right fixture panel. atalog # Description For use with Protector Hood: Shipping Wt. lbs./kg volts, 60 Hz Protector XL Floor-Mounted Laboratory Hood 6/ * 230 volts, 50 Hz Protector XL Floor-Mounted Laboratory Hood 6/2.7 Labconco orporation 8811 Prospect Avenue Kansas ity, Missouri FAX: labconco@labconco.com Home Page: ontact Labconco at or for ordering information on ceiling enclosure and rear finish panel kits, fire extinguishers, explosion-proof lighting, solid epoxy floors, tissue screens and distillation grids; and for blower sizing assistance by Labconco orporation Printed in the U.S.A. Product design subject to change without notice /12-James-1M-R1