Midmark Cabinet / Wall Light Installation

Transcription

1 Midmark Cabinet / Wall Light Installation [Full size template is available: ] warning Equipment is not suitable for use in the presence of a flammable anesthetic mixture. Equipment Alert Before installing the Midmark Cabinet / Wall Light, ensure the physical room requirements outlined are met. Applies to Models: (-002) (-002) (-001) (-001) Language of origin: English Physical Requirements NOTE: This install guide applies to Halogen and LED-style lights. Halogen LED Unit is shipped with a power cord and plug assembly. Where installation requires a power outlet, the outlet must be within 12 feet of wall or cabinet mounting in. (44.5 cm) in. (20.6 cm) 6.0 in. (15.2 cm) 360 AXIS F (constrained to 180 by wall) 56.0 in. (142.2 cm) Ceiling 93.5 in. (237.5 cm) 5.5 in. (14.0 cm) 16 in. on center (40.6 cm) Bottom of Mounting Bracket 18.0 in. (45.7 cm) AXIS D (does not rotate) 14.7 in. (37.3 cm) 96.0 in. (243.8 cm) Recommended height may vary due to 6 in. (15.2 cm) min. distance required for installation or personal preferences. All dimensions are based on a min. ceiling height of 8 ft. (244 cm). For every one inch below 8 ft. drop the mounting one inch. 62 5/16 in. (158.2 cm) 18.8 in. (47.8 cm) 16.0 in. (40.6 cm) 74.2 in. (188.5 cm) 75.0 in. (190.5 cm) 280 AXIS E 6.0 in. (15.2 cm) Floor Floor English Rev. R (6/21/13)

2 Physical Requirements...continued Equipment Alert Before installing the Midmark Cabinet / Wall Light, ensure the physical room requirements outlined are met. Center Column Installation 360 AXIS F 56.0 in. (142.2 cm) 93.5 in. (237.5 cm) 3.75 in. (9.53 cm) in. (11.75 cm) Ceiling 5.5 in. (14.0 cm) in. (20.6 cm) 6.0 in. (15.2 cm) 7.6 in. (19.3 cm) 14.7 in. (37.3 cm) 96.0 in. (243.8 cm) Bottom of Mounting Bracket Recommended min. 8 ft. (244 cm.) ceiling height due to the height of the central free standing cabinet and the 6 in. (15.2 cm) min. distance required between the light arm and the ceiling for installation. 62 5/16 in. (158.2 cm) Center Column 70.1 in. (178.1 cm) 75.0 in. (190.5 cm) 280 AXIS E AXIS D (does not rotate) 6.0 in. (15.2 cm) Floor Floor English-2

3 General Movement Characteristics General Information The support structure must be capable of supporting: System (only) Weight (Max.):...66 lbs (29.9 kgs) Torque (Max.): ft-lbs. (230.5 N m) In addition to supporting the above listed weights, the support structure must also be able to support the light without deflection. To prevent the suspension arm from drifting, the assembly must deflect no more than 1/16 in. (1.6 mm) over a 12 in. (30.5 cm) distance in. (142.2 cm) AXIS D 300 AXIS E 180 (no stops) 26.0 in. (66.0 cm) AXIS C 50 AXIS B in. (61.0 cm) AXIS A 180 English-3

4 Wall Mount Installation Location The wall mount assembly must be located so the operation of the light and arm assembly does not interfere with procedures or patient access. Power source must be within 12 feet of mounting location. Structure The wall mount backer plate must be leveled and secured with appropriate hardware to vertical wall studs or other substantial support structure capable of supporting the total weight of the light and arm assembly (refer to General Information). Power Source Light may be plugged into an appropriate wall outlet or wired to a suitable power source. The power source must be grounded, and protected by a 15 amp circuit breaker for 115 VAC operation or a 7.5 amp breaker for 230 VAC operation. All wiring must be applicable to state and local codes. * Recommended height may vary due to 6 in. (15.2 cm) min. distance required for installation or personal preferences. All dimensions are based on a min. ceiling height of 8 ft. (244 cm). For every 1 (2.54 cm) below 8 ft. drop the mounting 1. Step 1: Using template located on shipping box, place in position, level, and mark wall (outside) mount backer holes. Refer to chase installation manual for mounting hole locations. To install light, use hardware included with chase cabinet. (3/8 bolts, washers and nuts) Step 4: Remove light mount assembly from wall mount backer, four screws. Wall Mount Backer 16 in. (40.6 cm) on Center Wall Mount Backer Step 3: Slide wall mount cover from light mount assembly. Chase Light Mount Assembly Wall Mount Transformer 62 5/16 in. (158.2 cm) To Floor* Step 2: Remove transformer cover, four screws. English-4

5 Wall Mount Installation...continued Equipment Alert Failure to secure to a substantial structure with appropriate hardware capable of supporting the light assembly could result in equipment malfunctioning and damage. Step 5: Align mounting holes of wall mount backer with location holes on wall and secure with appropriate hardware. Check to assure wall mount backer is level. Step 6: Position light mount assembly on wall mount backer and secure with four screws. If supply voltage is 230 VAC refer to ADJUSTING TRANSFORMER FOR 230 VAC. 16 in. (40.6 cm) on Center Wall Mount Backer Step 7: Place wall mount cover in position on light mount assembly. Light Mount Assembly Wall Mount * Recommended height may vary due to 6 in. (15.2 cm) min. distance required for installation or personal preferences. All dimensions are based on a min. ceiling height of 8 ft. (244 cm). For every one inch below 8 ft. drop the mounting one inch. Transformer 62 5/16 in. (158.2 cm) To Floor* Step 8: Refer to Light Head and Arm Installation before installing transformer cover. English-5

6 Cabinet Mount Installation Location The cabinet mount assembly must be located so the operation of the light and arm assembly does not interfere with procedures or patient access. Power source must be within 12 feet of mounting location. Structure The cabinet mount must be leveled and secured to cabinet structure with appropriate hardware (1/4-20, grade 8, socket head cap screws) capable of supporting the total weight of the light and arm assembly (refer to General Information). Power Source Light may be plugged into an appropriate wall outlet or wired to a suitable power source. The power source must be grounded, and protected by a 15 amp circuit breaker for 115 VAC operation or a 7.5 amp breaker for 230 VAC operation. All wiring must be applicable to state and local codes. There are two sets of holes on the template for cabinet mounting. Inside holes are for drilling clearance holes when installing screws from the front into threaded holes or when using washers and nuts. The outer holes are when installing 1/4-20 screws through cabinet into mounting plate. Equipment Alert Failure to secure to a substantial structure capable of supporting the light assembly could result in equipment malfunctioning and damage. Mounting hardware must be 1/4 in.-20, grade 8, socket head cap screws and lockwashers. Step 1: Use existing holes from previous light or use template located on shipping box. Place template in position, level, and mark cabinet mounting holes. 1/4 Nylock nuts can be used when installation is on products other than Midmark. Step 2: Align mounting holes of mounting bracket with location holes on cabinet and secure with appropriate hardware. Check to assure mounting bracket is level. Outer Holes Template Inside Holes Mounting Bracket If supply voltage is 230 VAC refer to Adjusting Transformer for 230 VAC. Outer Holes Step 3: Refer to Light Head and Arm Installation before installing post mount cover. English-6

7 Adjusting Transformer for 230 VAC (Halogen ONLY) If supply voltage is 230 VAC, the following procedure must be performed before connecting power to light. Step 2: Disconnect brown lead from 115 V tap on transformer and connect to 230 V. Brown Lead Cabinet units may not have the post mount cover. Step 3: Install transformer cover and, where applicable, post mount cover. Transformer Post Mount Step 1: Remove transformer cover, one screw. English-7

8 Installing Plug to Power Cord If facility voltage is 230 VAC, install a properly rated plug according to local codes and regulations. Adjust transformer for 230 VAC operation. Step 2: A) Insert BROWN wire from power cord into hole (A) & tighten GOLD screw. B) Insert BLUE wire from power cord into hole (B) & tighten SILVER screw. C) Insert GREEN wire from power cord into hole (C) & tighten GREEN screw. Step 1: A) Remove screw as shown & three pronged portion of plug. B) Loosen two screws as shown & insert power cord into housing. Hole (A) Hole (C) Hole (B) Brown Wire Green Screw Green Wire The three pronged portion of plug may be installed in four different positions. Be sure two tabs on pronged portion align with notches in housing. Gold Screw Blue Wire Silver Screw Step 3: A) Rotate three pronged portion of plug to desired position in housing & secure with screw. B) Tighten two screws so that power cord is secured. Do not overtighten screws. Step 4: Plug power cord into properly rated receptacle & check for proper operation. English-8

9 Arm and Light Head Installation Fixed Arm Assembly Step 1: Place fixed arm assembly in position & connecting harness plug (A) from fixed arm to plug (B) on cabinet / wall mount assembly. Step 3: Insert collar onto fixed arm, snugging up set screw to hold it in place. A Bearing Housing B Key Collar Step 2: Insert fixed arm into bearing housing. Assure the collar is installed with the set screw toward the bottom. Do Not locate the set screw over the key. D C Flex Arm Step 4: Connect harness plug (C) from fixed arm to connector (D) in flex arm assembly. English-9

10 Arm and Light Head Installation...continued Equipment Alert To ensure quiet operation, apply a thin coat of lubricant (included w/light) to inside of fixed arm and bearing shaft of flex arm assembly. Fixed Arm Assembly Step 5: Insert end of flex arm into end of fixed arm. Install the key, then move collar down over the key & tighten set screw. : The set screw cannot be located over key. Step 8: On wall mount units, install transformer cover. Transformer Key Collar Step 6: Check level of fixed arm and, if necessary loosen or tighten four leveling screws. Flex Arm Leveling Screws Units are equipped with a separate 115 VAC plug for installation on the cord. The unit can also be direct wired to an appropriate circuit. Should a 230 VAC plug be desired it must be purchased locally. Step 7: Tighten mount screws to secure position. Mount Screws Step 9: Connect unit to the appropriate electrical supply. English-10

11 Tension Adjustments To adjust tension at Light pivot joint... A) Remove screw cover as shown. B) Loosen set screw. C) Loosen or tighten light pivot adjustment screw. D) Tighten set screw. Neck (Long Neck) Arm Pivot Adjustment Screws To adjust tension at Arm / Yoke pivot joints... A) Remove neck cover as shown (see ). B) Loosen or tighten appropriate screws to adjust tension. : Some halogen models have a short neck on the lighthead. It is not necessary to remove the neck cover on these models. Light Pivot Adjustment Screw Yoke Pivot Adjustment Screws Set Screw Short Neck Arm Pivot Adjustment Screw Yoke Pivot Adjustment Screw To adjust Flex Arm tension... A) Remove end cap and top cover as shown. B) Loosen or tighten adjustment nut as desired. Adjustment Nut English-11