SECTION WIRING DEVICES
|
|
- Cory Joseph
- 5 years ago
- Views:
Transcription
1 SECTION WIRING DEVICES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. General: Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification sections, apply to this section DESCRIPTION A. General: Provide factory fabricated wiring devices in type, color and electrical rating for the service indicated to provide convenient access to the electrical system for portable and permanent connections, and control of fixed outlets. B. Ratings: Voltage and ampere rating of switches and receptacles shall be marked on the device, and shall conform to Voltage and Ampacity of system to which applied. C. Hardware: Devices consist of all the necessary hardware to complete an installation and provide a margin of safety by inaccessibility of live electrical components DIMMING CONTROLS QUALITY ASSURANCE A. Manufacturers: Firms regularly engaged in manufacture of wiring devices, of types and ratings required, whose products have been in satisfactory use in similar service for not less than 5 years. Fully test all dimmers for proper operation prior to shipment from the factory. Equipment shall be as that manufactured by Lutron Electronics Co., Hubbell Manufacturing Co., Leviton Manufacturing. B. Installer: A firm with at least 5 years of successful installation experience on projects with electrical installation work similar to that required for the project. C. Warranty: Provide a minimum one-year warranty from time of installation acceptance RECEPTACLES AND SWITCHES QUALITY ASSURANCE A. Manufacturers: Manufacturers shall be companies regularly engaged in manufacture of wiring devices, of types and ratings required, whose products have been in satisfactory use in similar service for not less than 5 years. Acceptable manufacturers are Pass & Seymour, Hubbell, and Leviton Manufacturing. WIRING DEVICES
2 B. Installer: A firm with at least 5 years of successful installation experience on projects with electrical installation work similar to that required for the project. C. Compliance: Comply with the latest edition of the following standards; 1. NEMA WD1, WD3 and WD5 2. UL 5, 20 and ANSI/IEEE Standard C (Formerly IEEE 587) a. Test withstand voltage surges of up to 6000 volts and current surges of up to 200 amperes without damage. D. Warranty: Provide a minimum one-year warranty from time of final acceptance SUBMITTALS A. Wiring Devices: Submit manufacturer's product data on all wiring devices listed on the drawings including; 1. Colors 2. Dimensions 3. U.L. Label 4. Finish 5. Voltage 6. Wiring diagrams 7. Application information B. Coverplates and Identification: Submit type of identification used for coverplates to comply with the Identification Section as specified herein. Screws to match coverplate color SEQUENCING AND SCHEDULING A. Coordination: Coordinate with other work including wires/cables, electrical boxes and fittings, and raceways, to properly interface installation of all wiring devices. WIRING DEVICES
3 PART 2 - PRODUCTS 2.01 CONVENIENCE RECEPTACLES A. Twenty Ampere Receptacles: Provide commercial specification grade single or duplex receptacles, 2-pole, 3-wire grounding, with green hexagonal equipment ground screw, ground terminals and poles internally connected to mounting yoke, 20 ampere, 120 volts, with metal plaster ears, side wiring, NEMA configuration 5-20R unless otherwise indicated. B. Color: Devices connected to the normal system shall be grey in color, unless otherwise noted, for back of house and exterior locations (Mech, elec, storage, dishwashing, Burger King kitchens). C. Color: Devices connected to the normal system shall be white in color, unless otherwise noted, for main dining, Burger King dining, offices. D. Device Type: Unless otherwise noted, in all public areas, provide all receptacles as the duplex modular type. Provide standard devices in nonpublic areas such as storage rooms, janitor's closet, mechanical spaces, and electrical rooms. E. Construction: Heavy duty nylon face and wraparound mounting strap, locked into and on the body, utilizing heavy-gauge brass ground contacts riveted to strap. Include automatic self-grounding spring to assure ground continuity between mounting strap and metal wall box. T-slot one piece copper alloy contact wipes which interface with plug blades inserted at 3 points. Line terminals shall be screw terminals and accept #14 to #10 AWG copper conductors. F. Ground Fault Circuit Interrupter: Provide commercial specification grade, duplex, ground fault circuit interrupter receptacles, grounding type, UL rated Class A, Group 1, 20 ampere ratings, 125 volts, 60 Hz; with solid state ground fault sensing and signalling; with 5 milliampere ground fault trip level; equipped with 20 ampere receptacle configuration, NEMA 5-20R. Device shall contain test and reset pushbuttons, with a visual display of the tripped position. All outside receptacles (weatherproof) shall be duplex G.F.C.I. type. Interrupter shall resist tripping from the effects of radio frequency (RF) signals from 10 to 450 MHz. G. Isolated Ground: Manufacturer shall be Pass & Seymour, Leviton or Hubbell. Pass & Seymour Leviton Hubbell P/S 15A P/S 20A 15A 20A 15A 20A 6262-ISP 6362-ISP 8280-I 8380-I 8200 HIS 8300-HIS WIRING DEVICES
4 2.02 SWITCHES A. Toggle Switches: Provide specification grade, fast-make positive-break, flush single-pole, three and four way, silent operation toggle switches, 20 ampere, 120 volt AC or 277 volt AC as required, with mounting yoke insulated from mechanism, equipped with plaster ears, and side-wired screw terminals. B. Two Pole Switches: Provide two pole switches where drawings indicate the switching of 208 volt systems consisting of two phase conductors. C. Security Key Switches: Provide key switches where drawings indicate, where a degree of security requires limited access to control of the lighting system. D. Pilot Light Handle: Handle glows when switch is on. Handle color shall be clear, unless otherwise indicated. E. Thermal Switch: Provide fractional horsepower switch with melting alloy type overload relay, with number of poles to coordinate with the equipment being controlled. Surface or flush mounted cover, as required, equipped with padlocking device and pilot light. Provide overload relay heaters for each pole of the switch, sized per the manufacturer's instruction, and adjust heater size to permit normal operation of the motor. F. Color: Match receptacle device. Colors for locations identified in PLUGS AND CONNECTORS A. Standard: Comply with NEMA Standards Pub. No. WD WIRING DEVICE ACCESSORIES A. Faceplates: Unless otherwise noted, provide smooth faced nylon, single and ganged switch, receptacle, telephone, blank and other outlet wall plates for wiring devices, with ganging and cutouts as required B. Multigang: Provide all necessary hardware and frames to properly mount various devices in combinations. C. Exterior Device Covers: Provide "Weatherproof" duplex with stainless steel hinged cover. Device opening shall be standard or modular, to be compatible with the device provided for elsewhere in these specifications. D. Color: Unless otherwise noted, provide colored faceplates to match devices listed elsewhere in these specifications. WIRING DEVICES
5 2.05 PRODUCT DESIGN SELECTION A. Decora Premium Specification Grade Receptacles: Provide extra heavy duty specification grade receptacles as follows; Description Leviton Hubbell P & S 15 amp Single #16251 #2151 # amp Duplex #16262 #2152 # amp Single #16351 #2161 # amp Duplex #16362 #2162 # amp Duplex GFCI #6898 #GF-5362 #2091-S 20 amp Duplex Isolated Gnd. #16362-IG #IG-2162 #IG amp Duplex TVSS #5380 #5352-IS #6362-SP B. Standard Commercial Specification Grade Receptacles: Provide standard commercial specification grade receptacles as follows; Description Leviton Hubbell P & S 15 amp Single #5015 #5251 # amp Duplex #CR15 #CR15 # amp Single #5801 #5351 # amp Duplex #CR20 #CR20 # amp Duplex GFCI #6898 #GF-5352 #2091-S C. Premium Standard Specification Grade Switches: Provide premium standard specification grade switches as follows; Description Leviton Hubbell P & S 20 amp Single # #1221 #20AC1 20 amp 3-way # #1223 #20AC3 20 amp 4-way # #1224 #20AC4 20 amp Single-Locking #1221-2L #1221-L #20AC1-L 20 amp 3-way-Locking #1223-2L #1223-L #20AC3-L 20 amp 4-way-Locking #1224-2L #1224-L #20AC4-L 20 amp Single-Pilot #1221-2PL #1221-PL #20AC1- CPL 20 amp 3-way-Pilot #1223-2PL #1223-PL #20AC3- CPL D. Decora Commercial Specification Grade Switches: Provide commercial specification standard commercial grade switches as follows; WIRING DEVICES
6 Description Leviton Hubbell P & S 20 amp Single #2121 #2121 # amp 3-way #2123 #2123 # amp 4-way #2124 #2124 # amp Single-Locking #1221-L #1221-L #521-L 20 amp 3-way-Locking #1223-L #1223-L #523-L 20 amp 4-way-Locking #1224-L #1224-L #524-L 20 amp Single-Pilot #1221-2PL #1221-2PL #20AC1- CPL 20 amp 3-way-Pilot #1223-2PL #1223-2PL #20AC3- CPL E. Motor Starter Switches: Provide motor starter type switches as follows; Description Square D Manual motor starter Class 2510 switch with overloads Manual motor starter Class 2510 switch with overloads and pilot light F. Device Covers: Provide device covers as follows; Description Leviton Hubbell P & S Stainless steel coverplate #302 S/S #302 #302 Thermoplastic nylon 807--series ---- RP series coverplate 804--N series Weatherproof stainless ---- # WP-8 steel coverplate Weatherproof stainless SP-26L steel coverplate locking type WIRING DEVICES
7 PART 3 - EXECUTION 3.01 INSTALLATION OF WIRING DEVICES A. General: Provide wiring devices, in accordance with manufacturer's written instructions, applicable requirements of NEC and National Electrical Contractors Associations "Standard of Installation", and in accordance with recognized industry practices to ensure that products serve intended function. B. Completion: Delay installation of devices until wiring and wall finish is completed. C. Support: Devices shall be securely supported to box, not supported to device plate. Device shall trim out flush with front of plate. Do not support the device by loosening device mounting screws and attaching the coverplate for leveling. D. Adjustment: Provide receptacles and switches only in electrical boxes which are clean, free from excess building materials, debris, etc. Adjust devices to plumb when tightened, and in position to receive faceplate. Devices shall not be leveled by using the mounting screws, outlet boxes shall be flush to wall finish prevent leveling problems. Tighten devices and provide securely, so that there shall be no movement during usage. E. Position: Position ground pin at the top of the device in vertical application, unless otherwise noted. F. Wiring: Provide screw terminal connections using a single conductor only. Do not "back-stab" devices. Provide single whips for all multiple conductor connections within each box APPLICATION OF COVER PLATES A. Mounting: Provide coverplates in true vertical or horizontal alignment as applicable. Plates shall be properly secured by means of screws which have heads with finish matching the plate. Secure plates so as to maintain a snug fit against wall surfaces with no gaps. B. Replacement: Replace all coverplates which are warped, cracked, chipped, or whose color does not match the balance of the installation. Replace screws whose threads do not allow the drawing up tight of the coverplate to the device. WIRING DEVICES
8 3.03 CLEANING A. Soiled Devices: Clean devices soiled prior to acceptance inspection, to remove all debris and foreign materials, such as paint, varnish, drywall compound, etc. B. Solutions: Do not use liquid cleaning solutions, etc. on the face of the devices without written direction from the Engineer/Architect TESTING A. Ground testing: Provide ground testing procedures as specified herein. Prior to energizing circuitry, test wiring devices for electrical continuity, and for short circuits. B. Polarity: Subsequent to energization, test wiring devices for proper polarity, and to demonstrate operations as required in this and other sections of this Specification. C. Recording: Record all tests as required in other sections of this specification. END OF SECTION WIRING DEVICES
East Central College
SECTION 262726 - WIRING DEVICES PART 1 - GENERAL 1.1 WORK INCLUDES A. Base and Alternate Bids: 1. Contractor Provide: a. Wall switches. b. Receptacles c. Device plates and decorative box covers. 1.2 RELATED
More informationA. Products shall be designed, manufactured, tested, and installed in compliance with the following standards:
SECTION 26 27 26 WIRING DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General Provisions,
More informationA. Products shall be designed, manufactured, tested, and installed in compliance with the following standards:
SECTION 26 29 13 ENCLOSED MOTOR CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationSECTION PANELBOARDS
SECTION 16470 PANELBOARDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. The general provisions of the contract including General and Special Conditions and General Requirements shall apply to all work under
More informationUniversity of Houston Master Construction Specifications Insert Project Name SECTION ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL
SECTION 23 04 10 ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section
More informationSECTION ENCLOSED SWITCHES AND CIRCUIT BREAKERS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 29 21 ENCLOSED SWITCHES AND CIRCUIT BREAKERS SPEC WRITE NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not
More informationDIVISION 16 - ELECTRICAL SECTION 16xx0 MANUFACTURED WIRING SYSTEM ACCESS FLOOR
DIVISION 16 - ELECTRICAL SECTION 16xx0 16xx0-1. GENERAL MANUFACTURED WIRING SYSTEM ACCESS FLOOR The modular convenience power system ensures the electrification and delivery of power from the power panels
More informationElegance Electrician s Installation Guide
Elegance Electrician s Installation Guide CentraLite Systems, Inc. 6420 Wall St. Mobile, AL 36695 Phone: 877-466-5483 Fax: 251-607-9119 2003-2005 CentraLite Systems, Inc. Revised 10/20/2005 ELECTRICIAN
More informationSECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationMichigan State University Construction Standards SECONDARY UNIT SUBSTATIONS PAGE
PAGE 261116-1 SECTION 261116 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationIN2 Enclosed Switches and Circuit Breakers
Illinois Math and Science Academy DigitalCommons@IMSA Project Manuals IN2 2015 IN2 Enclosed Switches and Circuit Breakers Illinois Mathematics and Science Academy Follow this and additional works at: http://digitalcommons.imsa.edu/facility_in2_manuals
More informationSECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 22 1123.13 DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationA. This Section includes ac, enclosed controllers rated 600 V and less, of the following types:
SECTION 262913 600 VOLT ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 0 Specification
More informationWARREN COUNTY, N.Y. M/E REFERENCE
SECTION 262000 - ELECTRIC DISTRIBUTION PART 1 - GENERAL 1.1 DESCRIPTION A. Provide a complete secondary distribution system as indicated on the Contract Documents and as specified herein. 1.2 QUALITY ASSURANCE
More informationSTRAIGHT BLADE PLUGS & CONNECTORS
STRAIGHT BLADE PLUGS & CONNECTORS Quick-thread assembly screws and cord-grip screws come backed-out, ready-to-wire. See-through, thermoplastic terminal chamber for clear view of terminals and wire connections.
More informationSection SWITCHBOARDS. Introduction. Part 1 - General. Related Work
Section 16435 - SWITCHBOARDS Introduction Part 1 - General Related Work Section 16070 Seismic Anchorage and Restraint Section 16075 Electrical Identification Section 16080 Power Distribution Acceptance
More informationUniversity of Houston Master Construction Specifications Insert Project Name
SECTION 26 13 13 MEDIUM VOLTAGE SWITCHGEAR PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationDESIGN GUIDELINES LOW VOLTAGE SWITCHGEAR PAGE 1 of 5
DESIGN GUIDELINES LOW VOLTAGE SWITCHGEAR PAGE 1 of 5 1.1. APPLICABLE PUBLICATIONS 1.1.1. Publications listed below (including amendments, addenda, revisions, supplements, and errata), form a part of this
More informationTRI-SERVICE ELECTRICAL WORKING GROUP (TSEWG) 03/05/09 TSEWG TP-11: UFC N BEST PRACTICES
TSEWG TP-11: UFC 3-500-10N BEST PRACTICES UFC 3-500-10N was developed by NAVFAC and was used as the starting point for the tri-services development of UFC 3-500-10, Design: Electrical Engineering. UFC
More informationDIVISION 26 ELECTRICAL SECTION CIRCUIT BREAKERS
DIVISION 26 ELECTRICAL SECTION 26 28 19 PART 1 GENERAL 1.01 DESCRIPTION A. Furnish and install circuit breakers in switchboards, distribution panelboards, and separate enclosures for overcurrent protection
More informationSECTION MOTOR CONTROL
SECTION 26 24 19 MOTOR CONTROL PART 1 - GENERAL 1.1 SECTION INCLUDES A. Manual motor starters B. Magnetic motor starters C. Combination magnetic motor starters D. Solid-state reduced voltage motor starters
More informationA. Provide a complete system of overcurrent protective devises as indicated on the drawings, and as specified herein.
16475 OVERCURRENT PROTECTIVE DEVICES ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 26 28 16 An optional
More information1. The term "withstand" means "the unit will remain in place without separation of any parts from the device when subjected to the seismic forces.
SECTION 262816 - ENCLOSED SWITCHES AND CIRCUIT BREAKERS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Fusible switches. 2. Nonfusible switches. 3. Receptacle switches. 4. Shunt trip switches. 5.
More informationMECHANICAL AND ELECTRICAL COORDINATION SECTION MECHANICAL AND ELECTRICAL COORDINATION PART 1 - GENERAL
13686.00 MECHANICAL AND ELECTRICAL COORDINATION 230002-1 SECTION 230002 MECHANICAL AND ELECTRICAL COORDINATION 1.1 WORK INCLUDED PART 1 - GENERAL A. Work Included in This Section: Materials, equipment,
More informationA 120V BR GFI Recpt. Features. Material, Color, and Finish. Description
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 AllenWatson@elliottelectric.com 2095 20A 120V BR GFI Recpt. Pass & Seymour/Legrand Catalog Number 2095 Manufacturer Pass
More informationBUSWAY Low Voltage (Pow-R-Flex)
BUSWAY LOW VOLTAGE (POW-R-FLEX) PART 1 GENERAL 1.01 1.02 SCOPE The Contractor shall furnish and install the busway system including all necessary fittings, hangers and accessories as specified herein and
More informationSECTION ENCLOSED CONTROLLERS
SECTION 16420 ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION DISTRIBUTION AND GROUNDING
SECTION 16400 DISTRIBUTION AND GROUNDING PART 1 GENERAL 1.01 SECTION INCLUDES A. Furnishing and installation of a complete electrical distribution and grounding system. B. Furnish and install motor control
More informationSwitches & Motor Controls
Toggle Switches... A-2 Traditional Switches... A-2 CO/ALR Switches... A-14 Lev-Lok Modular Switches... A-15 Decora Switches... A-16 Appliance Switches... A-23 Anywhere RF Remote Switches... A-25 Manual
More informationA. Motors shall be designed, built, and tested in accordance with the latest revision of the following standard documents.
PART 1: GENERAL 1.01 This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is to apply the
More informationA. Work Included: Provide low voltage switchboard work as shown, scheduled, indicated, and as specified.
SECTION 26 24 13 LOW VOLTAGE SWITCHBOARDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationSECTION ENCLOSED SWITCHES AND CIRCUIT BREAKERS
SECTION 26 28 16 ENCLOSED SWITCHES AND PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following individually mounted, enclosed switches and circuit breakers rated 600V AC and less: 1. Fusible switches.
More informationA. Submit manufacturer's literature and technical data before starting work.
SECTION 16425 SWITCHBOARD PART 1 GENERAL 1.01 SUMMARY A. Related Section: 1. 16450 - Grounding. 1.02 SUBMITTALS A. Submit manufacturer's literature and technical data before starting work. B. Submit Shop
More informationMULTI 9 System Catalog IEC Rated C60N/H/L Circuit Breakers
IEC Rated C60N/H/L Circuit Breakers Standard Features Fast Closing Allows increased withstand to the high inrush currents of some loads Trip-free mechanism: Contacts cannot be held in the on position when
More informationSECTION MOTORS, MOTOR STARTERS, VARIABLE FREQUENCY DRIVES AND ELECTRICAL WORK
PART 1 - GENERAL 1.1 GENERAL: SECTION 15150 MOTORS, MOTOR STARTERS, VARIABLE FREQUENCY DRIVES AND ELECTRICAL WORK A. The Mechanical Contractor shall furnish to the Electrical Contractor for installation,
More informationHorizontal Circuit Switchers
> Transformer Protection > CIRCUIT SWITCHERS C A T A L O G B U L L E T I N General Application Southern States Types CSH and CSH-B Horizontal Circuit Switchers provide an economical, versatile, space saving
More informationHorizontal Circuit Switchers
> Transformer Protection > CIRCUIT SWITCHERS C A T A L O G B U L L E T I N General Application Southern States Types CSH and CSH-B Horizontal Circuit Switchers provide an economical, versatile, space saving
More informationISIMET/MAPA, LLC, an affiliate of WCM Industries, Inc. 103 CJ Wise Parkway Naples, TX (903) fax (903)
ISIMET/MAPA, LLC, an affiliate of WCM Industries, Inc. 103 CJ Wise Parkway Naples, TX 75568 (903) 897-0737 fax (903) 897-0740 Pedestal Starter-Disconnect Pedestal Starter Controller Installation Instructions
More informationSPECIFICATION HIGH IMPACT RESISTANT THERMOPLASTIC
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 2095TRWRI 20A 125V Spec TR & WR Gfci Rec Pass & Seymour/Legrand Catalog Number 2095TRWRI Manufacturer Pass & Seymour/Legrand
More information1. Division 26 Section "Elevator Shunt-Trip Fused Disconnect Switches".
SECTION 26 28 16 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections,
More informationThree-Phase Pole Mounted Recloser
Three-Phase Pole Mounted Recloser Page 1 of 8 Table of Contents 1 GENERAL... 3 2 CONSTRUCTION... 3-5 3 BUSHINGS... 5 4 LINE CONNECTOR... 5 5 TOOLS....5 6 NAMEPLATES..6 7 PAINT... 6 8 EXTERNAL HARDWARE
More informationSlim is in. Hospital Grade SmartlockPro Slim GFCI Receptacles. Specification and Ordering Guide
Hospital Grade SmartlockPro Slim GFCI Receptacles Specification and Ordering Guide n Shallow profile design is easier to install in all electrical boxes n Same SmartlockPro advantages you've come to rely
More informationSPECIFICATIONS - DETAILED PROVISIONS Section Vertical Hollowshaft Electric Motors C O N T E N T S
Revised 04/14/2016 SPECIFICATIONS - DETAILED PROVISIONS Section 16151 - Vertical Hollowshaft Electric Motors C O N T E N T S PART 1 - GENERAL... 1 1.01 SCOPE... 1 1.02 SPECIFIC PROJECT REQUIREMENTS...
More informationMipco Connections for Refrigerated Containers. No One Does It Like Mipco. The Mipco. Advantage. Reliability. Safety. Easy Installation & Service
No One Does It Like Mipco Mipco Interlocked Reefer Power Outlets are used extensively in port terminals and shipboard applications to provide a safe, watertight electrical connection for refrigerated containers.
More informationOverload Relay Heater Tables
Overload Relay Tables of Elements for Overload Relays General Use only when motor full load current is not known. Motor amps will vary depending on the type and manufacturer of the motor. These average
More informationInstruction Sheet for Powertite Plug, Connector and Receptacle
330087 Instruction Sheet for Powertite Plug, Connector and Receptacle Powertite 200 Amp Pin & Sleeve Receptacles, Cable Connectors and Plugs: NEMA 4X. 600 Volt AC, 250 Volt DC. Wire Recess Diameter:.687.
More informationQuik-Spec Coordination Panelboard Specifications
Quik-Spec Coordination Panelboard Specifications 30A - 400A Fusible Panelboards SECTION 26 24 XX (This Specification references CSI MasterFormat 2004) FUSIBLE BRANCH CIRCUIT PANELBOARDS PART 1 1.01 SUMMARY
More informationFACT SHEET Standard: Electrical Safety
What is a Ground Fault Circuit Interrupter? FACT SHEET The ground-fault circuit interrupter, or GFCI, is a fast-acting circuit breaker designed to shut off electric power in the event of a ground-fault
More informationA. This Section includes Low Voltage Switchgear Work, as indicated on the drawings, and as specified herein.
16425 SWITCHBOARD ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 26 24 13 An optional keynote to
More informationD. Operation and Maintenance Data. In addition to items specified in Division 1 Section "Operation and Maintenance Data," include the following:
SECTION 16211 - ELECTRICITY METERING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationMedium Voltage Standby non-paralleling Control GUIDE FORM SPECIFICATION
Medium Voltage Standby non-paralleling Control 1. GENERAL GUIDE FORM SPECIFICATION A. The requirements of the contract, Division 1, and part 16 apply to work in this section. 1.01 SECTIONS INCLUDE A. Medium
More informationFused Coordination Panelboard
Fused Coordination Panelboard SOLUTIONS GUIDE SOLUTIONS GUIDE Branch Circuit Protection Introducing Mersen s Fused Coordination Panelboard Selective Coordination is required in several locations as defined
More informationSECTION GENERAL-SERVICE AIR COMPRESSOR PART 1 - GENERAL
13686.00 GENERAL SERVICE AIR COMPRESSOR 221519-1 SECTION 22 1519 - GENERAL-SERVICE AIR COMPRESSOR 1.1 RELATED DOCUMENTS PART 1 - GENERAL A. Drawings and general provisions of the Contract, including General
More informationA. Fan motors and associated equipment shall be sized to operate at 110% of calculated loads and capacities.
PART 1: GENERAL 1.01 This design guidelines contained herein includes the requirements electric motors utilized for electric motor driven systems at Texas State University. It is the intention of this
More informationSECTION HYDRAULIC FOUR FOLD DOORS MODEL 48 LOUVERS
SECTION 08350 HYDRAULIC FOUR FOLD DOORS MODEL 48 LOUVERS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1
More informationUniversity of Houston Master Construction Specifications Insert Project Name
SECTION 26 24 14 600 VOLT DRAWOUT SWITCHGEAR PART 1 - GENERAL 1.01 SECTION INCLUDES: A. Individually mounted rear-accessible low voltage switchgear ANSI rated switchgear and low voltage power circuit breakers
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationIce Rink Renovation & New Clubhouse
SECTION 262913 - ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSUBSTATION VACUUM CIRCUIT BREAKER (15.5KV)
SUBSTATION VACUUM CIRCUIT BREAKER (15.5KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities
More informationSECTION MOTORS AND VARIABLE FREQUENCY DRIVES
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Related Sections: 1. Section 15050 - Basic Mechanical Requirements. 2. Section 15051 - Motors. 3. Section 15185 - Hydronic Pumps. 4. Section 15625 - Centrifugal
More informationSUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV)
SUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products
More informationSUBSTATION VACUUM CIRCUIT BREAKER (38KV)
SUBSTATION VACUUM CIRCUIT BREAKER (38KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities
More informationOTEC Transfer switch open transition
Specification sheet OTEC Transfer switch open transition 40 1200 amp Description OTEC transfer switches are designed for operation and switching of electrical loads between primary power and Standby generator
More informationSECTION MOTOR CONTROLLERS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 29 11 SPEC WRITER NOTE: Use this section only for NCA projects. Delete between // ---- // if not applicable to project. Also, delete any other item or paragraph
More informationA. Provide variable frequency drives to operate variable torque loads as shown on the Drawings and as specified herein.
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION 23 90 71 PART 1 GENERAL 1.01 DESCRIPTION A. Provide variable frequency drives to operate variable torque loads as shown on the Drawings
More informationA 120V 20A Gfci RCPT. Features. Dimensions and Weight. Description. Manufacturer Information PASS & SEYMOUR GTIN
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 1597 15A 120V 20A Gfci RCPT Pass & Seymour/Legrand Catalog Number 1597 Manufacturer Pass & Seymour/Legrand Description
More informationSTATE OF NEW JERSEY DEPARTMENT OF TRANSPORTATION TRENTON, NEW JERSEY 08625
STATE OF NEW JERSEY DEPARTMENT OF TRANSPORTATION TRENTON, NEW JERSEY 08625 SPECIFICATIONS FOR A 19 INCH RACK BASE MOUNT (HEATER/AC) (ENVIRONMENTAL FIELD TERMINAL CABINET) N. J. Specification No. Effective
More informationProduct Specifications for Aluminum Vertical Break Switches
1. General a) This specification covers the design, manufacture, and shipment of aluminum vertical break switches, both air-break and load-break configurations, for substation and transmission switching
More informationSPECIFICATION HIGH IMPACT RESISTANT THERMOPLASTIC/NYLON
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 2094 Gfci Rec 20a120v20a Pass & Seymour/Legrand Catalog Number 2094 Manufacturer Pass & Seymour/Legrand Description Receptacle,
More informationSECTION DC POWER SUPPLY/BATTERY CHARGER
SECTION 26 33 05 PART 1 - GENERAL 1.1 THE REQUIREMENT A. The CONTRACTOR shall provide the single-phase heavy-duty industrial battery charger and all accessories required, complete and operable, in accordance
More informationPREFACE ********************************************************** IT IS NOT INTENDED THAT THESE STANDARDS BE COPIED AND USED AS A SPECIFICATION!
PREFACE This publication has been prepared as a guide for Architectural and Engineering (A&E) firms in the preparation of documents for the design and construction of new structures and the remodeling
More informationCHAPTER V RESIDENTIAL WIRING
CHAPTER V RESIDENTIAL WIRING 5.1. THE SERVICE ENTRANCE Buildings and other structures receive the electrical energy through the service entrance. In residential wiring, the electric company supply this
More informationCENTER BREAK GROUP OPERATED AIR BREAK SWITCHES RATED 15.5kV THROUGH 170kV EFFECTIVE DATE: 10/25/16 REV B
CENTER BREAK GROUP OPERATED AIR BREAK SWITCHES RATED 15.5kV THROUGH 170kV EFFECTIVE DATE: 10/25/16 REV B TCV2 Hubbell has a policy of continuous product improvement. Please visit hubbellpowersystems.com
More informationControls. CONTROLS AND ACCESSORIES PRODUCT FAMILY FEATURES DIMMERS DIMENSIONS SPECIFICATION SERIES STANDARD FEATURES
SPECIFICATION SUBMITTAL s The contractor s choice in rugged, linear slide dimmers. www.lutron.com/nova CONTROLS AND ACCESSORIES Slide-to-Off s Preset s Select light level with slider; slide down to off
More informationUBC Technical Guidelines Section Edition Commissioning of Electrical Systems Page 1 of 5
Page 1 of 5 1.0 GENERAL 1.1 Coordination Requirements.1 UBC Building Operations Electrical Technical Support.2 UBC Energy & Water Services 2.0 REQUIREMENTS FOR COMMISSIONING AND TESTING 2.1 Testing.1 Unit
More informationCITY OF LOMPOC UTILITIES DEPARTMENT ELECTRICAL DIVISION SPECIFICATION NO. ELE-112 SUBSTATION CLASS VACUUM CIRCUIT BREAKERS OCTOBER 2008
CITY OF LOMPOC UTILITIES DEPARTMENT ELECTRICAL DIVISION SPECIFICATION NO. ELE-112 SUBSTATION CLASS VACUUM CIRCUIT BREAKERS OCTOBER 2008 SPECIFICATION NO: ELE_112_R1.doc Page 1 of 3 Rev. 10/28/2008 SPECIFICATION
More informationSTRAIGHT BLADE PLUGS & CONNECTORS
STRAIGHT BLADE PLUGS & CONNECTORS Quick-thread assembly screws and cord-grip screws come backed-out, ready-to-wire. See-through, thermoplastic terminal chamber for clear view of terminals and wire connections.
More informationSECTION MOTOR CONTROLLERS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 29 11 MOTOR CONTROLLERS SPEC WRITER NOTE: Delete between // ---- // if not applicable to project. Also, delete any other item or paragraph not applicable to
More informationDesign Standard. Purpose: Design Standard:
Design Standard Purpose: This design standard has the purpose of creating a consistent application of motor-control centers throughout the East Side Union High School District, therefore achieving a standard
More informationModel Description Vac. Max rating Pedestal Only: 36 Utility Pedestal W/O Disconnect General Duty Series:
MAPA Products MPD-XX / Pedestal Disconnect 30, 60, 100 amp February 2014 Pedestal Disconnect Installation Instructions Parts List MAPA Products Fusible Rainproof Pedestal Mounted Safety Switch provides
More informationElectropneumatic Timing Relays Series 7000 Industrial
DESIGN FEATURES Available in On-Delay, True Off-Delay, and On/Off-Delay. Timing from 0.1 seconds to 60 minutes, fully calibrated in linear increments. Oversize time-calibrated adjustment knobs, serrated
More informationHospital Products HBL Extra Heavy Duty Hospital Grade Duplex Receptacles
HBL Extra Heavy Duty Duplex Receptacles Features and Benefits One-piece nickel-plated brass integral ground strap for greater corrosion resistance Patented ground contact provides redundant grounding Unique
More informationB. Fabricate in accordance with ASHRAE handbooks and SMACNA duct manuals. A. Submit in accordance with Division-1 and Section
SECTION 15910 DUCT ACCESSORIES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract including General and Supplementary Conditions, Division-1 Specification Sections,
More informationIndustrial Control Transformers
6 Industrial Control Transformers Section 6 Industrial Control Transformers provide a low and safe control voltage for the operation of electromagnetic devices, such as motor starters, contactors, solenoids
More informationSOLAR HEATING SYSTEM
SECTION 13600 SOLAR HEATING SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 07600 - Flashing and Sheet Metal. 2. 07900 - Joint Sealers. 3. 15260 - Thermal Insulation (Plumbing). 4. 15410 - Piping
More informationSECTION MOTORS & MOTOR CONTROLLERS
SECTION 15170 MOTORS & MOTOR CONTROLLERS PART 1 GENERAL 1.01 SECTION INCLUDES A. Electric motors. B. Motor controllers for Packaged equipment. 1.02 SUBMITTALS A. Wiring diagrams with electrical characteristics
More informationTypical Specification
Engineered to Order Built to Last Typical Specification VAULT VRPFI, TWO POSITION, ROTARY PUFFER SWITCHGEAR PART 1- GENERAL 1.1 DESCRIPTION A. The switch shall consist of manually operated load interrupting,
More informationUTILITY DISTRIBUTION SYSTEMS
SECTION 11419 UTILITY DISTRIBUTION SYSTEMS PART 1 GENERAL 1.01 SECTION INCLUDES A. Related Sections: 1. 11401 - Custom Fabricated Equipment. 2. 11405 - Cooking Equipment. 3. Division 15 - Water supply,
More informationType MTS Miniature Test Switches
Type MTS Miniature Test Switches o o o o Compact and versatile Front- and back-connected styles Safe, durable, rugged and reliable Recognized by CUL & UL DESCRIPTION In many panelboard, switchgear, metering,
More informationQuick Start Guide TS 910 & TS 920
Quick Start Guide TS 910 & TS 920 DANGER HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH Read and understand this quick start guide before installing and operating the transfer switch The installer
More informationSECTION MOTOR REQUIREMENTS for HVAC
PART 1 GENERAL 1.1 SECTION INCLUDES A. Single-phase electric motors B. Three-phase electric motors 1.2 REFERENCES SECTION 23 05 13 MOTOR REQUIREMENTS for HVAC A. ABMA 9 - Load Ratings and Fatigue Life
More informationArrow Hart hospital grade GFCI modular receptacles
Technical Data Arrow Hart hospital grade GFCI Description 2-pole, 3-wire grounding 15A 125V/AC 20A 125V/AC TAMPER RESISTANT SGFH20_MOD Design features ArrowLink modular plug and connector incorporate a
More informationWP Plugs and DS Receptacles For FS and FD Cast Device Boxes
WP Plugs and DS Receptacles For FS and FD Cast Device Boxes Weatherproof 3F Application: WP plugs and DS receptacles are used: wherever dust, dirt, moisture and corrosion are a problem outdoors or in locations
More informationCovers for Cast Iron or Aluminum Device Boxes
Single Gang Blank cover for enclosing splices and taps where device not used. Sheet DS100 Flush Sheet steel DSS100 For GFI receptacles. Sheet steel DS23 GFI For square handle general use snap or toggle
More informationThis is intended to provide uniform application of the codes by the plan check staff and to help the public apply the codes correctly.
SUPPLEMENTAL CORRECTION SHEET FOR SOLAR PHOTOVOLTAIC SYSTEMS (ELEC) This is intended to provide uniform application of the codes by the plan check staff and to help the public apply the codes correctly.
More informationLow Voltage Switchgear Type WL Low Voltage Metal-Enclosed Switchgear
13 Low Voltage Switchgear Siemens Type WL low voltage metal-enclosed switchgear is designed, constructed and tested to provide superior power distribution, power monitoring and control. At the heart of
More informationInstalling Power Components
This chapter provides instructions on how to install and reinstall power components in the Cisco NCS 4016 chassis. It also covers connecting and disconnecting power and powering on the chassis. The Cisco
More informationMAGNETIC MOTOR STARTERS
Chapter 6 MAGNETIC MOTOR STARTERS 1 The basic use for the magnetic contactor is for switching power in resistance heating elements, lighting, magnetic brakes, or heavy industrial solenoids. Contactors
More informationWallplates & Weather Protective Covers
SECTION C Wallplates & Weather Protective Covers Our broad offering of wallplates are the final touch for any application and are available in standard size, mid-size and oversize. Choose from a variety
More informationArc Fault Circuit Interrupter (AFCI) FACT SHEET
Arc Fault Circuit Interrupter (AFCI) FACT SHEET THE AFCI The AFCI is an arc fault circuit interrupter. AFCIs are newly-developed electrical devices designed to protect against fires caused by arcing faults
More information