Effect of concave plug shape of a control valve on the fluid flow characteristics using computational fluid dynamics

Size: px
Start display at page:

Download "Effect of concave plug shape of a control valve on the fluid flow characteristics using computational fluid dynamics"

Transcription

1 Effect of concave plug shape of a control valve on the fluid flow characteristics using computational fluid dynamics Yasser Abdel Mohsen, Ashraf Sharara, Basiouny Elsouhily, Hassan Elgamal Mechanical Engineering Department Faculty of engineering Alexandria University-Egypt ABSTRACT: control valves are commonly used as fluid flow control equipment in many engineering applications. Thus it is more and more essential to know the flow characteristic inside the valve. Due to the fast progress of the flow simulation and numerical technique, it becomes possible to observe the flow inside a valve and to study its performance. This paper presents the modeling and simulation of a control valve. The flow system in a control valve has a complex structure and non-linear characteristics, because of its construction and the fluid flow phenomena associated with it. the three-dimensional CFD simulation is conducted to observe the fluid flow characteristics when a control valve is equipped with different concave plug shapes and different openings. Furthermore, the results of the three-dimensional analysis can be used in the design for low noise and efficiency improvement. Keywords: flow induced valve, characteristics for flow passing throw control valve, plug geometry effect on flow passing control valve, Control valve CFD analysis, control valve plug geometry effect on its vibration, effect of valve configuration on flow passing throw valve, INTRODUCTION The optimum design of a control valve requires a preliminary estimation of the lift force acting on the plug for the flow passing through it. In order to solve this problem, many experimental measurements on specific valves are needed. Alternatively, a numerical analysis can be performed by means of computational fluid dynamics (CFD) codes. In previous works, the fluid forces acting on an open center directional control valve were the aim of studies the evaluation of the driving forces acting on ¾ hydraulic center directional control valve by means of computational fluid dynamic analysis are studied [1]. Macro et al. [2,3],Del Vescovo and Lippolis [4]analyzed the effects that different spool edge shapes produce on the flow force profile during the axial spool movement. Del Vescovo et al. [5-7]analyzed the difference between the fluid dynamics behavior of a proportional valve and a traditional one. Recently, Computational Fluid Dynamics (CFD) has been experiencing rapid advances due to both computer technology progress and efficient algorithms that have been developed to solve the Navier- Stokes (N-S) equations used in the flow analysis around ship hull. The work contributed to the numerical solution of the viscous flow around ship-like bodies is discussed in [8]. The experimental and numerical works on a three-dimensional, complex geometry, control valve were performed for model validation and improved understanding of valve flow features is discussed in [9]. The compressible air flow in a typical puffer chamber with moving contact between fixed electrodes has been studied using computational fluid dynamics techniques [10]. In recent years, the valve manufacturers across the world focused their attention towards developing high 2016 RS Publication, rspublicationhouse@gmail.com Page 159

2 performance control valve designs to outweigh the problems caused by the conventional control valve. Typical problems faced in the industry with conventional control valves are the vibration of the system. This vibration in the system t can be attributed to many reasons like pressure force affecting on the valve plug under the partialvalve-opening condition. In this paper, the attention has been focused on the plug control valve, and that the modeled geometry is necessarily three dimensional although the periodicity of the geometrical domain has been exploited in order to reduce the computational efforts. Physical Boundary Trim Area Inlet Flow Velocity Outlet Flow Figure 1: An internal view for the valve configuration Model description and boundary conditions and grid generation In this section the plug with a different concave shape is describe and the grid generations require getting the best solution. And show the boundary condition used in this study. 1-Flat face plug:- In this case a plug is used with flat faced as shown in figure 2. The plug opening is to be changed from 10% to 40% 2- Plug with concave shape no. 1 Figure 2: flat face plug 2016 RS Publication, rspublicationhouse@gmail.com Page 160

3 In this case a plug with concave shape is considered (see figure 3). The shape follows the equation 2 y = х х Figure 3: Plug with concave shape no.1 3-Plug with concave shape no. 2 In this case the plug geometry (see figure 4) follows the equation 2 y = х х Figure 4: plug with concave shape no.2 The Boundary condition Symmetry boundary conditions were used at the plane of symmetry of the valve body and plug assembly. All solid boundaries were represented assuming the no slip condition to exist. Inlet conditions were represented by uniform velocity sufficient to provide the required large Re flow. The 2016 RS Publication, rspublicationhouse@gmail.com Page 161

4 inlet velocity varies from 1m/s to 5m/s. the valve opining varies from 10% to 40%. The Body Forces are neglected. Outlet boundary condition set as with uniform pressure. Grid generations The grid used in the numerical study was a tetrahedral grid. After an initial investigation for the grid independence, a grid size of 40 by 25 was used. The nodes of the grid were clustered in the plug and seat region since this was the area of largest flow gradient. In addition, an effort was mad to reduce the grid distortion. Figure 5 shows the geometry of the valve body and plug arrangement and the flow field meshing. Figure 5: Valve body and plug arrangement with field mesh RESULTS AND DISCUSSION Analysis of flow passing through the control valve is performed using CFD model. A flat faced plug and two plugs with the different concave shapes are considered RS Publication, rspublicationhouse@gmail.com Page 162

5 lift force(n) International Journal of Advanced Scientific and Technical Research Issue 6 volume 6, November-December 2016 Flat faced plug The CFD results in Fig. 6 show that the relation between the valve percent opening and lift force when the flow passing throw the valve with flat face plug with the different inlet velocities. It can be seen when the valve opening is small, the lift force is large at the same flow inlet velocity. When the valve opening is large, the lift force is small at the same flow inlet velocity. As the flow inlet velocity increases the lift force increases for the same valve opening. This means that the lift force reaches its maximum value at smallest opening for the same inlet velocity and it reaches its maximum value at highest flow inlet velocity at the same valve opening. The lift force reaches its minimum value at the large valve opening for the same flow inlet velocity v=1m/s v=2m/s v=3m/s v=4m/s v=5m/s 0 0% 10% 20% 30% 40% 50% valve opening Figure 6: Relation between lift force acting on flat faced plug and percentage valve opening for different inlet velocities Plug with different parabolic shapes. The relation between the lift force and valve opening for two plugs having concave shape are shown in figures 7 and 8. For all plug geometry the lift force increases when the valve opening decreases. And it also increases when the inlet velocity increases. The lift force attains its maximum value at smallest opening and it reaches its minimum value at opening 40%. After 40% opening it reaches an asymptotic value for all plug geometries. At small inlet velocity the change of lift force with valve opening is low. At high velocity inlet the change of it is high. The comparison between the previous result for flat faced plug geometry and the latter result shows that 2016 RS Publication, rspublicationhouse@gmail.com Page 163

6 lift force (N) lift force(n) International Journal of Advanced Scientific and Technical Research Issue 6 volume 6, November-December 2016 the lift force decreases when the concave plug geometry curvature increases. The lift force attains its maximum value for flat face plug. The lift force reaches its minimum value for the plug shape no v=1m/s v=2m/s v=3m/s v=4m/s v=5m/s 0 0% 10% 20% 30% 40% 50% valve opening Figure 7: Relation between lift forces acting on plug with concave shape no.1 and percentage valve opening for different inlet velocities v=1m/s v=2m/s v=3m/s v=4m/s v=5m/s 0 0% 10% 20% 30% 40% 50% valve opening Figure 8: Relation between lift force acting on plug with concave shape no.2 and percentage valve opening for different inlet velocities 2016 RS Publication, rspublicationhouse@gmail.com Page 164

7 Examination of valve pressure contours Figure 9-17 displays the numerical pressure contours with valves different plugs.each valve is shown at opening 10, 20, 30, and 40 percent. In each case the pressure decreases in the downstream direction with the largest pressure gradient occurring in the plug and seat region. No significant pressure changes are observed upstream of valve only minor changes are observed downstream of the plug. The pressure changes are observed when the valve percent opening, flow inlet velocity and valve plug geometry change. At small valve opening the pressure increases around the plug region and it decrease at low inlet velocity. The pressure for flat face plug region is higher than the concave plug region and it decreases to minimum forthe concave plug no. 2. Figure 9: Pressure contours for flat faced plug at valve opening 10% and v=1m/s Figure 10: Pressure contours for flat faced plug at valve opening 20% and v=3m/s 2016 RS Publication, Page 165

8 Figure 11: Pressure contours for flat faced plug at valve opening 40% and v=5m/s Figure 12: Pressure contours for p1 plug at valve opening 10% and v=1m/s 2016 RS Publication, Page 166

9 Figure 13: Pressure contours for p1 plug at valve opening 20% and v=3m/s Figure 14: Pressure contours for p1 plug at valve opening 40% and v=5m/s 2016 RS Publication, Page 167

10 Figure 15: Pressure contours for p2 plug at valve opening 10% and v=1m/s Figure 16: Pressure contours for p2 plug at valve opening 20% and v=3m/s 2016 RS Publication, Page 168

11 Figure 17: Pressure contours for p2 plug at valve opening 40% and v=5m/s CONCLUSIONS The analysis of flow passing through the control valve using a three-dimensional model has been investigated by solving the Navier-stokes and the continuity equations using comsol CFD code. From the results it is concluded that 1- The lift force acting on the plug decreases when the plug concave shape curvature increases for constant valve opening and for the same inlet velocity. 2- The lift force acting on the plug increases when the valve opening decreases for specific plug shape and the same inlet velocity. 3- The lift force acting on the plug increases when the inlet velocity increases for the same plug shape and the same valve opening. REFRENCES [1] R. Amirante, G. Del Vescovo and A. Lippolis, Evaluation of the flow forces on an open centre directional control valve by means of a computational fluid dynamic analysis. Journal of Energy conversion and management. Vol. 47, PP (2006). [2] Macor A,Badin D.Turbulence modeling influence on flow force analysis in hydraulic directional control valves.in :proceeding of the 54 th congress nazionle ATI, 1999 [in Italian]. [3] Macor A. Experimental analysis on a directional valve with a flat notch metering section. In: proceeding of the 57 th congresso nazional ATI, pisa, 2002 [in Italian]. [4] Del Vwscovo G, Lippolis A. Flow force analysis on an electro piloted hydraulic directional control valve. In proceeding of the 3 rd international congress Minihydro, Maratea, 2001 [in Italian] [5] Del Vescovo G, Lippolis A. CFD analysis of flow forces on spool valves. In : Proceedings of the 1 st international confrance on computational method in fluid power technology, Melbourne November 26-28,2003;2003. [6] Del Vescovo G,Lippolis A.Three dimensional analysis of flow forces on directional control valves. Int J Fluid power 2003;4(2). [7] Del Vescovo GLippolis A. flow forces analysis on a four way valve. In: proceedings of 2 nd FPN PhD international symposium, Modena, July 3-6, 2002; RS Publication, rspublicationhouse@gmail.com Page 169

12 [8] S. Hayashi, T.Matsui and T. Ito, Study of flow and thrust in nozzle-flapper valves Journal of fluid engineer. Trans. ASME, Vol 45, PP (1975). [9] K. K. Botros, G.H. Dunn and J. A. Hrycyk, Riser-Relief valve dynamic interaction Journal of Fluids Engineering. Vol. 119 PP (1997). [10] B. Min, F. Xin, C. Ying, Scholl Frank, Computational fluid dynamic approach to pressure loss analysis of hydraulic spool valve Journal of Energy Conversion Management. Vol. 149 PP (2000) RS Publication, Page 170

International Journal of Scientific & Engineering Research, Volume 5, Issue 7, July-2014 ISSN

International Journal of Scientific & Engineering Research, Volume 5, Issue 7, July-2014 ISSN ISSN 9-5518 970 College of Engineering Trivandrum Department of Mechanical Engineering arundanam@gmail.com, arjunjk91@gmail.com Abstract This paper investigates the performance of a shock tube with air

More information

Design and Test of Transonic Compressor Rotor with Tandem Cascade

Design and Test of Transonic Compressor Rotor with Tandem Cascade Proceedings of the International Gas Turbine Congress 2003 Tokyo November 2-7, 2003 IGTC2003Tokyo TS-108 Design and Test of Transonic Compressor Rotor with Tandem Cascade Yusuke SAKAI, Akinori MATSUOKA,

More information

Numerical Study on the Flow Characteristics of a Solenoid Valve for Industrial Applications

Numerical Study on the Flow Characteristics of a Solenoid Valve for Industrial Applications Numerical Study on the Flow Characteristics of a Solenoid Valve for Industrial Applications TAEWOO KIM 1, SULMIN YANG 2, SANGMO KANG 3 1,2,4 Mechanical Engineering Dong-A University 840 Hadan 2 Dong, Saha-Gu,

More information

Effect of Stator Shape on the Performance of Torque Converter

Effect of Stator Shape on the Performance of Torque Converter 16 th International Conference on AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 16 May 26-28, 2015, E-Mail: asat@mtc.edu.eg Military Technical College, Kobry Elkobbah, Cairo, Egypt Tel : +(202) 24025292

More information

SOLAR FLAT PLATE COLLECTOR HEAT TRANSFER ANALYSIS IN THE RAISER WITH HELICAL FINS Mohammed Mohsin Shkhair* 1, Dr.

SOLAR FLAT PLATE COLLECTOR HEAT TRANSFER ANALYSIS IN THE RAISER WITH HELICAL FINS Mohammed Mohsin Shkhair* 1, Dr. ISSN 2277-2685 IJESR/May 2015/ Vol-5/Issue-5/352-356 Mohammed Mohsin Shkhair et. al./ International Journal of Engineering & Science Research SOLAR FLAT PLATE COLLECTOR HEAT TRANSFER ANALYSIS IN THE RAISER

More information

CFD Analysis and Comparison of Fluid Flow Through A Single Hole And Multi Hole Orifice Plate

CFD Analysis and Comparison of Fluid Flow Through A Single Hole And Multi Hole Orifice Plate CFD Analysis and Comparison of Fluid Flow Through A Single Hole And Multi Hole Orifice Plate Malatesh Barki. 1, Ganesha T. 2, Dr. M. C. Math³ 1, 2, 3, Department of Thermal Power Engineering 1, 2, 3 VTU

More information

Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics

Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics M. Metwally Lecturer, Ph.D., MTC, Cairo, Egypt Abstract Modern offset printing machine, paper

More information

CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate

CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate Sandeep M, U Sathishkumar Abstract In this paper, a study of different cross section bundle arrangements

More information

Theoretical and Experimental Investigation of Compression Loads in Twin Screw Compressor

Theoretical and Experimental Investigation of Compression Loads in Twin Screw Compressor Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2004 Theoretical and Experimental Investigation of Compression Loads in Twin Screw Compressor

More information

FLOW AND HEAT TRANSFER ENHANCEMENT AROUND STAGGERED TUBES USING RECTANGULAR VORTEX GENERATORS

FLOW AND HEAT TRANSFER ENHANCEMENT AROUND STAGGERED TUBES USING RECTANGULAR VORTEX GENERATORS FLOW AND HEAT TRANSFER ENHANCEMENT AROUND STAGGERED TUBES USING RECTANGULAR VORTEX GENERATORS Prabowo, Melvin Emil S., Nanang R. and Rizki Anggiansyah Department of Mechanical Engineering, ITS Surabaya,

More information

Influence of pantograph fixing position on aerodynamic characteristics of high-speed trains

Influence of pantograph fixing position on aerodynamic characteristics of high-speed trains DOI 1.17/s4534-17-125-y Influence of pantograph fixing position on aerodynamic characteristics of high-speed trains Liang Zhang 1 Jiye Zhang 1 Tian Li 1 Weihua Zhang 1 Received: 28 September 216 / Revised:

More information

ABSTRACT I. INTRODUCTION III. GEOMETRIC MODELING II. LITERATURE REVIW

ABSTRACT I. INTRODUCTION III. GEOMETRIC MODELING II. LITERATURE REVIW 2017 IJSRSET Volume 3 Issue 5 Print ISSN: 2395-1990 Online ISSN : 2394-4099 Themed Section: Engineering and Technology Performance Analysis of Helical Coil Heat Exchanger Using Numerical Technique Abhishek

More information

THE EFFECT OF BLADE LEAN ON AN AXIAL TURBINE STATOR FLOW HAVING VARIOUS HUB TIP RATIOS. Dr. Edward M Bennett

THE EFFECT OF BLADE LEAN ON AN AXIAL TURBINE STATOR FLOW HAVING VARIOUS HUB TIP RATIOS. Dr. Edward M Bennett THE EFFECT OF BLADE LEAN ON AN AXIAL TURBINE STATOR FLOW HAVING VARIOUS HUB TIP RATIOS Dr. Edward M Bennett ABSTRACT The effect of simple lean on an axial turbine stator was examined using a threedimensional

More information

Unsteady Flow Condition of Centrifugal Pump for Low Viscous Fluid Food

Unsteady Flow Condition of Centrifugal Pump for Low Viscous Fluid Food International Journal of Fluid Machinery and Systems DOI: http://dx.doi.org/.593/ijfms.7..4.43 Vol., No. 4, October-December IN (Online): 88-9554 Original Paper Unsteady Flow Condition of Centrifugal Pump

More information

Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results

Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2012 Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured

More information

CFD analysis on the aerodynamics characteristics of Jakarta-Bandung high speed train

CFD analysis on the aerodynamics characteristics of Jakarta-Bandung high speed train CFD analysis on the aerodynamics characteristics of Jakarta-Bandung high speed train Tony Utomo 1,*, Berkah Fajar 1, and Hendry Arpriyanto 2 1 Mechanical Engineering Department, Faculty of Engineering,

More information

Investigation for Flow of Cooling Air through the Ventilated Disc Brake Rotor using CFD

Investigation for Flow of Cooling Air through the Ventilated Disc Brake Rotor using CFD International Journal of Thermal Technologies E-ISSN 2277 4114 2015 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijtt/ Research Article Investigation for Flow of Cooling Air

More information

Analysis of Exhaust System using AcuSolve

Analysis of Exhaust System using AcuSolve Analysis of Exhaust System using AcuSolve Abbreviations: CFD (Computational Fluid Dynamics), EBP (Exhaust Back Pressure), RANS (Reynolds Averaged Navier Stokes), Spalart Allmaras (SA), UI (Uniformity Index)

More information

CFD on Cavitation around Marine Propellers with Energy-Saving Devices

CFD on Cavitation around Marine Propellers with Energy-Saving Devices 63 CFD on Cavitation around Marine Propellers with Energy-Saving Devices CHIHARU KAWAKITA *1 REIKO TAKASHIMA *2 KEI SATO *2 Mitsubishi Heavy Industries, Ltd. (MHI) has developed energy-saving devices that

More information

NUMERICAL INVESTIGATION OF PISTON COOLING USING SINGLE CIRCULAR OIL JET IMPINGEMENT

NUMERICAL INVESTIGATION OF PISTON COOLING USING SINGLE CIRCULAR OIL JET IMPINGEMENT NUMERICAL INVESTIGATION OF PISTON COOLING USING SINGLE CIRCULAR OIL JET IMPINGEMENT BALAKRISHNAN RAJU, CFD ANALYSIS ENGINEER, TATA CONSULTANCY SERVICES LTD., BANGALORE ABSTRACT Thermal loading of piston

More information

INVESTIGATION OF HEAT TRANSFER CHARACTERISTICS OF CIRCULAR AND DIAMOND PILLARED VANE DISC BRAKE ROTOR USING CFD

INVESTIGATION OF HEAT TRANSFER CHARACTERISTICS OF CIRCULAR AND DIAMOND PILLARED VANE DISC BRAKE ROTOR USING CFD SDRP JOURNAL OF NANOTECHNOLOGY & MATERIAL SCIENCE. INVESTIGATION OF HEAT TRANSFER CHARACTERISTICS OF CIRCULAR AND DIAMOND PILLARED VANE DISC BRAKE ROTOR USING CFD Research AUTHOR: A.RAJESH JUNE 2017 1

More information

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine Available online atwww.scholarsresearchlibrary.com Archives of Applied Science Research, 2016, 8 (7):31-40 (http://scholarsresearchlibrary.com/archive.html) ISSN 0975-508X CODEN (USA) AASRC9 Comparison

More information

Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny. Turbomachinery 2015, Design of HP and LP turbine connection

Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny. Turbomachinery 2015, Design of HP and LP turbine connection Turbostroje 2015 Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny Turbomachinery 2015, Design of HP and LP turbine connection J. Hrabovský 1, J. Klíma 2, V. Prokop 3, M. Komárek 4 Abstract:

More information

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Vikas Kumar Agarwal Deputy Manager Mahindra Two Wheelers Ltd. MIDC Chinchwad Pune 411019 India Abbreviations:

More information

Chapter 7: Thermal Study of Transmission Gearbox

Chapter 7: Thermal Study of Transmission Gearbox Chapter 7: Thermal Study of Transmission Gearbox 7.1 Introduction The main objective of this chapter is to investigate the performance of automobile transmission gearbox under the influence of load, rotational

More information

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS 8 FASCICLE VIII, 8 (XIV), ISSN 11-459 Paper presented at Bucharest, Romania ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS Laurentia ANDREI 1), Gabriel ANDREI 1) T, Douglas

More information

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY CFD ANALYSIS OF GAS COOLER FOR ASSORTED DESIGN PARAMETERS B Nageswara Rao * & K Vijaya Kumar Reddy * Head of Mechanical Department,

More information

IMPROVING BOILER COMBUSTION USING COMPUTATIONAL FLUID DYNAMICS MODELLING

IMPROVING BOILER COMBUSTION USING COMPUTATIONAL FLUID DYNAMICS MODELLING REFEREED PAPER IMPROVING BOILER COMBUSTION USING COMPUTATIONAL FLUID DYNAMICS MODELLING VAN DER MERWE SW AND DU TOIT P John Thompson, Sacks Circle, Bellville South, 7530, South Africa schalkv@johnthompson.co.za

More information

(1) Keywords: CFD, helicopter fuselage, main rotor, disc actuator

(1) Keywords: CFD, helicopter fuselage, main rotor, disc actuator SIMULATION OF FLOW AROUND FUSELAGE OF HELICOPTER USING ACTUATOR DISC THEORY A.S. Batrakov *, A.N. Kusyumov *, G. Barakos ** * Kazan National Research Technical University n.a. A.N.Tupolev, ** School of

More information

INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING

INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING Journal of KONES Powertrain and Transport, Vol. 7, No. 4 200 INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING Emil Toporcer, Peter Tunik University of Žilina, Faculty of Mechanical Engineering Department

More information

Fig 2: Grid arrangements for axis-symmetric Rocket nozzle.

Fig 2: Grid arrangements for axis-symmetric Rocket nozzle. CFD Analysis of Rocket-Ramjet Combustion Chamber 1 Ms. P.Premalatha, Asst. Prof., PSN College of Engineering and Technology, Tirunelveli. 1prema31194@gmail.com 1 +91-90475 26413 2 Ms. T. Esakkiammal, Student,

More information

Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM

Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM V Prabhu Raja, J Kanchana, K Ramachandra, P Radhakrishnan PSG College of Technology, Coimbatore - 641004 Abstract Loss of machining

More information

Analysis of Air Flow and Heat Transfer in Ventilated Disc Brake Rotor with Diamond Pillars

Analysis of Air Flow and Heat Transfer in Ventilated Disc Brake Rotor with Diamond Pillars International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2016 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Analysis

More information

Computational Fluid Dynamics in Torque Converters: Validation and Application

Computational Fluid Dynamics in Torque Converters: Validation and Application Rotating Machinery, 9: 411 418, 2003 Copyright c Taylor & Francis Inc. ISSN: 1023-621X print DOI: 10.1080/10236210390241646 Computational Fluid Dynamics in Torque Converters: Validation and Application

More information

CONJUGATE HEAT TRANSFER ANALYSIS OF HELICAL COIL HEAT EXCHANGE USING CFD

CONJUGATE HEAT TRANSFER ANALYSIS OF HELICAL COIL HEAT EXCHANGE USING CFD CONJUGATE HEAT TRANSFER ANALYSIS OF HELICAL COIL HEAT EXCHANGE USING CFD Rudragouda R Patil 1, V Santosh Kumar 2, R Harish 3, Santosh S Ghorpade 4 1,3,4 Assistant Professor, Mechanical Department, Jayamukhi

More information

CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump

CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump ISSN 2395-1621 CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump #1 SuhasThorat, #2 AnandBapat, #3 A. B. Kanase-Patil 1 suhas31190@gmail.com 2 dkolben11@gmail.com 3 abkanasepatil.scoe@sinhgadedu.in

More information

Investigation of converging slot-hole geometry for film cooling of gas turbine blades

Investigation of converging slot-hole geometry for film cooling of gas turbine blades Project Report 2010 MVK160 Heat and Mass Transport May 12, 2010, Lund, Sweden Investigation of converging slot-hole geometry for film cooling of gas turbine blades Tobias Pihlstrand Dept. of Energy Sciences,

More information

CFD ANALYSIS OF PRESSURE DROP CHARACTERISTICS OF BUTTERFLY AND DUAL PLATE CHECK VALVE

CFD ANALYSIS OF PRESSURE DROP CHARACTERISTICS OF BUTTERFLY AND DUAL PLATE CHECK VALVE CFD ANALYSIS OF PRESSURE DROP CHARACTERISTICS OF BUTTERFLY AND DUAL PLATE CHECK VALVE Adarsh K M 1, Dr. V Seshadri 2 and S. Mallikarjuna 3 1 M Tech Student Mechanical, MIT-Mysore 2 Professor (Emeritus),

More information

ENGINE COMBUSTION SIMULATION USING OPENFOAM

ENGINE COMBUSTION SIMULATION USING OPENFOAM ENGINE COMBUSTION SIMULATION USING OPENFOAM K. S. Kolambe 1, S. L. Borse 2 1 Post Graduate Engineering Student, Department of Mechanical Engineering. 2, Associate Professor, Department of Mechanical Engineering

More information

Friction and Vibration Characteristics of Pneumatic Cylinder

Friction and Vibration Characteristics of Pneumatic Cylinder The 3rd International Conference on Design Engineering and Science, ICDES 214 Pilsen, Czech Republic, August 31 September 3, 214 Friction and Vibration Characteristics of Pneumatic Cylinder Yasunori WAKASAWA*

More information

Enhance the Performance of Heat Exchanger with Twisted Tape Insert: A Review

Enhance the Performance of Heat Exchanger with Twisted Tape Insert: A Review Enhance the Performance of Heat Exchanger with Twisted Tape Insert: A Review M.J.Patel 1, K.S.Parmar 2, Umang R. Soni 3 1,2. M.E. Student, department of mechanical engineering, SPIT,Basna, Gujarat, India,

More information

e t Performance of Extended Inlet and Extended Outlet Tube on Single Expansion Chamber for Noise Reduction

e t Performance of Extended Inlet and Extended Outlet Tube on Single Expansion Chamber for Noise Reduction e t International Journal on Emerging Technologies 7(1): 37-41(2016) ISSN No. (Print) : 0975-8364 ISSN No. (Online) : 2249-3255 Performance of Extended Inlet and Extended Outlet Tube on Single Expansion

More information

Computational flow field analysis of a Vertical Axis Wind Turbine

Computational flow field analysis of a Vertical Axis Wind Turbine Computational flow field analysis of a Vertical Axis Wind Turbine G.Colley 1, R.Mishra 2, H.V.Rao 3 and R.Woolhead 4 1 Department of Engineering & Technology Huddersfield University Queensgate Huddersfield,

More information

COMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER

COMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER COMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER Masaru SHIMADA*, Hideharu YAMAMOTO* * Hardware System Development Department, R&D Division JATCO Ltd 7-1, Imaizumi, Fuji City, Shizuoka, 417-8585 Japan

More information

University of Huddersfield Repository

University of Huddersfield Repository University of Huddersfield Repository Colley, Gareth, Mishra, Rakesh, Rao, H.V. and Woolhead, R. Performance evaluation of three cross flow vertical axis wind turbine configurations. Original Citation

More information

COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report R0. By Kimbal A.

COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report R0. By Kimbal A. COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report 412509-1R0 By Kimbal A. Hall, PE Submitted to: WESTFALL MANUFACTURING COMPANY May 2012 ALDEN RESEARCH

More information

Numerical Investigation of the Effect of Excess Air and Thermal Power Variation in a Liquid Fuelled Boiler

Numerical Investigation of the Effect of Excess Air and Thermal Power Variation in a Liquid Fuelled Boiler Proceedings of the World Congress on Momentum, Heat and Mass Transfer (MHMT 16) Prague, Czech Republic April 4 5, 2016 Paper No. CSP 105 DOI: 10.11159/csp16.105 Numerical Investigation of the Effect of

More information

Marc ZELLAT, Driss ABOURI and Stefano DURANTI CD-adapco

Marc ZELLAT, Driss ABOURI and Stefano DURANTI CD-adapco 17 th International Multidimensional Engine User s Meeting at the SAE Congress 2007,April,15,2007 Detroit, MI RECENT ADVANCES IN DIESEL COMBUSTION MODELING: THE ECFM- CLEH COMBUSTION MODEL: A NEW CAPABILITY

More information

NUMERICAL INVESTIGATION OF FLUID FLOW AND HEAT TRANSFER CHARACTERISTICS ON THE AERODYNAMICS OF VENTILATED DISC BRAKE ROTOR USING CFD

NUMERICAL INVESTIGATION OF FLUID FLOW AND HEAT TRANSFER CHARACTERISTICS ON THE AERODYNAMICS OF VENTILATED DISC BRAKE ROTOR USING CFD THERMAL SCIENCE: Year 2014, Vol. 18, No. 2, pp. 667-675 667 NUMERICAL INVESTIGATION OF FLUID FLOW AND HEAT TRANSFER CHARACTERISTICS ON THE AERODYNAMICS OF VENTILATED DISC BRAKE ROTOR USING CFD by Thundil

More information

Aerodynamic Characteristics of Sedan with the Rolling Road Ground Effect Simulation System

Aerodynamic Characteristics of Sedan with the Rolling Road Ground Effect Simulation System Vehicle Engineering (VE) Volume 2, 2014 www.seipub.org/ve Aerodynamic Characteristics of Sedan with the Rolling Road Ground Effect Simulation System Yingchao Zhang 1, Linlin Ren 1, Kecheng Pan 2, Zhe Zhang*

More information

Transactions on Modelling and Simulation vol 10, 1995 WIT Press, ISSN X

Transactions on Modelling and Simulation vol 10, 1995 WIT Press,   ISSN X Flow characteristics behind a butterfly valve M. Makrantonaki," P. Prinos,* A. Goulas' " Department of Agronomy, Faculty of Technological Science, University of Thessalia, Greece * Hydraulics Laboratory,

More information

Marc ZELLAT, Driss ABOURI, Thierry CONTE and Riyad HECHAICHI CD-adapco

Marc ZELLAT, Driss ABOURI, Thierry CONTE and Riyad HECHAICHI CD-adapco 16 th International Multidimensional Engine User s Meeting at the SAE Congress 2006,April,06,2006 Detroit, MI RECENT ADVANCES IN SI ENGINE MODELING: A NEW MODEL FOR SPARK AND KNOCK USING A DETAILED CHEMISTRY

More information

Thermal Analysis of Shell and Tube Heat Exchanger Using Different Fin Cross Section

Thermal Analysis of Shell and Tube Heat Exchanger Using Different Fin Cross Section Thermal Analysis of Shell and Tube Heat Exchanger Using Different Fin Cross Section J. Heeraman M.Tech -Thermal Engineering Department of Mechanical Engineering Ellenki College of Engineering & Technology

More information

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS POLISH MARITIME RESEARCH Special Issue 2018 S2 (98) 2018 Vol. 25; pp. 30-34 10.2478/pomr-2018-0070 MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

More information

THERMAL ANALYSIS OF DIESEL ENGINE PISTON USING 3-D FINITE ELEMENT METHOD

THERMAL ANALYSIS OF DIESEL ENGINE PISTON USING 3-D FINITE ELEMENT METHOD INTERNATIONAL JOURNAL OF MANUFACTURING TECHNOLOGY AND INDUSTRIAL ENGINEERING (IJMTIE) Vol. 2, No. 2, July-December 2011, pp. 97-102 THERMAL ANALYSIS OF DIESEL ENGINE PISTON USING 3-D FINITE ELEMENT METHOD

More information

Advanced Aerodynamic Design Technologies for High Performance Turbochargers

Advanced Aerodynamic Design Technologies for High Performance Turbochargers 67 Advanced Aerodynamic Design Technologies for High Performance Turbochargers TAKAO YOKOYAMA *1 KENICHIRO IWAKIRI *2 TOYOTAKA YOSHIDA *2 TORU HOSHI *3 TADASHI KANZAKA *2 SEIICHI IBARAKI *1 In recent years,

More information

COMPUTATIONAL FLUID DYNAMICS ANALYSIS OF THE ACOUSTIC PERFORMANCE OF VARIOUS SIMPLE EXPANSION CHAMBER MUFFLERS

COMPUTATIONAL FLUID DYNAMICS ANALYSIS OF THE ACOUSTIC PERFORMANCE OF VARIOUS SIMPLE EXPANSION CHAMBER MUFFLERS COMPUTATIONAL FLUID DYNAMICS ANALYSIS OF THE ACOUSTIC PERFORMANCE OF VARIOUS SIMPLE EXPANSION CHAMBER MUFFLERS Middelberg, J.M., Barber, T.J., Leong, S. S., Byrne, K.P and Leonardi, E. School of Mechanical

More information

A Study on Performance Enhancement of Heat Exchanger in Thermoelectric Generator using CFD

A Study on Performance Enhancement of Heat Exchanger in Thermoelectric Generator using CFD IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 10 March 2016 ISSN (online): 2349-6010 A Study on Performance Enhancement of Heat Exchanger in Thermoelectric

More information

Flow Behavior and Friction Factor. in Internally Grooved Pipe Wall

Flow Behavior and Friction Factor. in Internally Grooved Pipe Wall Adv. Studies Theor. Phys., Vol. 8, 2014, no. 14, 643-647 HIKARI Ltd, www.m-hikari.com http://dx.doi.org/10.12988/astp.2014.4573 Flow Behavior and Friction Factor in Internally Grooved Pipe Wall Putu Wijaya

More information

EXPERIMENTAL INVESTIGATION OF THE FLOWFIELD OF DUCT FLOW WITH AN INCLINED JET INJECTION DIFFERENCE BETWEEN FLOWFIELDS WITH AND WITHOUT A GUIDE VANE

EXPERIMENTAL INVESTIGATION OF THE FLOWFIELD OF DUCT FLOW WITH AN INCLINED JET INJECTION DIFFERENCE BETWEEN FLOWFIELDS WITH AND WITHOUT A GUIDE VANE Proceedings of the 3rd ASME/JSME Joint Fluids Engineering Conference July 8-23, 999, San Francisco, California FEDSM99-694 EXPERIMENTAL INVESTIGATION OF THE FLOWFIELD OF DUCT FLOW WITH AN INCLINED JET

More information

Integrated 1D-MultiD Fluid Dynamic Models for the Simulation of I.C.E. Intake and Exhaust Systems

Integrated 1D-MultiD Fluid Dynamic Models for the Simulation of I.C.E. Intake and Exhaust Systems Integrated -MultiD Fluid Dynamic Models for the Simulation of I.C.E. Intake and Exhaust Systems G. Montenegro, A. Onorati, F. Piscaglia, G. D Errico Politecnico di Milano, Dipartimento di Energetica, Italy

More information

The Effect of Spark Plug Position on Spark Ignition Combustion

The Effect of Spark Plug Position on Spark Ignition Combustion The Effect of Spark Plug Position on Spark Ignition Combustion Dr. M.R. MODARRES RAZAVI, Ferdowsi University of Mashhad, Faculty of Engineering. P.O. Box 91775-1111, Mashhad, IRAN. m-razavi@ferdowsi.um.ac.ir

More information

Abstract In this study the heat transfer characteristics inside a rectangular duct with circular, rectangular, drop

Abstract In this study the heat transfer characteristics inside a rectangular duct with circular, rectangular, drop International Journal of Scientific & Engineering Research, Volume 7, Issue 5, May-2016 25 INVESTIGATION OF HEAT TRANSFER CHARACTERISTICS IN A RECTNAGULAR CHANNEL WITH PERFORATED DROP SHAPED PIN FINS C.

More information

PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE

PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE PREDICTION OF PISTON SLAP OF IC ENGINE USING FEA BY VARYING GAS PRESSURE V. S. Konnur Department of Mechanical Engineering, BLDEA s Engineering College, Bijapur, Karnataka, (India) ABSTRACT The automotive

More information

Flow Characteristics in an Augmentation Channel of a Direct Drive Turbine for Wave Power Generation

Flow Characteristics in an Augmentation Channel of a Direct Drive Turbine for Wave Power Generation The 10 th Asian International Conference on Fluid Machinery 21 st 23 rd October 2009, Kuala Lumpur Malaysia Paper ID: AICFM0131 Flow Characteristics in an Augmentation Channel of a Direct Drive Turbine

More information

Gauge Face Wear Caused with Vehicle/Track Interaction

Gauge Face Wear Caused with Vehicle/Track Interaction Gauge Face Wear Caused with Vehicle/Track Interaction Makoto ISHIDA*, Mitsunobu TAKIKAWA, Ying JIN Railway Technical Research Institute 2-8-38 Hikari-cho, Kokubunji-shi, Tokyo 185-8540, Japan Tel: +81-42-573-7291,

More information

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4

More information

PHYSICAL MODEL TESTS OF ICE PASSAGE AT LOCKS

PHYSICAL MODEL TESTS OF ICE PASSAGE AT LOCKS Ice in the Environment: Proceedings of the 16th IAHR International Symposium on Ice Dunedin, New Zealand, 2nd 6th December 22 International Association of Hydraulic Engineering and Research PHYSICAL MODEL

More information

Study on Flow Fields in Variable Area Nozzles for Radial Turbines

Study on Flow Fields in Variable Area Nozzles for Radial Turbines Vol. 4 No. 2 August 27 Study on Fields in Variable Area Nozzles for Radial Turbines TAMAKI Hideaki : Doctor of Engineering, P. E. Jp, Manager, Turbo Machinery Department, Product Development Center, Corporate

More information

Development of Variable Geometry Turbocharger Contributes to Improvement of Gasoline Engine Fuel Economy

Development of Variable Geometry Turbocharger Contributes to Improvement of Gasoline Engine Fuel Economy Development of Variable Geometry Turbocharger Contributes to Improvement of Gasoline Engine Fuel Economy 30 MOTOKI EBISU *1 YOSUKE DANMOTO *1 YOJI AKIYAMA *2 HIROYUKI ARIMIZU *3 KEIGO SAKAMOTO *4 Every

More information

A LES/RANS HYBRID SIMULATION OF CANOPY FLOWS

A LES/RANS HYBRID SIMULATION OF CANOPY FLOWS BBAA VI International Colloquium on: Bluff Bodies Aerodynamics & Applications Milano, Italy, July, - 8 A ES/RANS HYBRID SIMUATION OF CANOPY FOWS Satoru Iizuka and Hiroaki Kondo Nagoya University Furo-cho,

More information

Effects of Dilution Flow Balance and Double-wall Liner on NOx Emission in Aircraft Gas Turbine Engine Combustors

Effects of Dilution Flow Balance and Double-wall Liner on NOx Emission in Aircraft Gas Turbine Engine Combustors Effects of Dilution Flow Balance and Double-wall Liner on NOx Emission in Aircraft Gas Turbine Engine Combustors 9 HIDEKI MORIAI *1 Environmental regulations on aircraft, including NOx emissions, have

More information

FLOW CONTROL THROUGH VORTEX SHEDDING INTERACTION OF ONE CYLINDER DOWNSTREAM OF ANOTHER. Jonathan Payton 1, and *Sam M Dakka 2

FLOW CONTROL THROUGH VORTEX SHEDDING INTERACTION OF ONE CYLINDER DOWNSTREAM OF ANOTHER. Jonathan Payton 1, and *Sam M Dakka 2 International Journal of GEOMATE, May, 2017, Vol.12, Issue 33, pp. 53-59 Geotec., Const. Mat. &Env., ISSN:2186-2990, Japan, DOI: http://dx.doi.org/10.21660/2017.33.2565 FLOW CONTROL THROUGH VORTEX SHEDDING

More information

Spray Injectors within Large Capacity Molten Sulfur Combustion: Fluid- Structure Interaction Study

Spray Injectors within Large Capacity Molten Sulfur Combustion: Fluid- Structure Interaction Study Available online at w w w.sciencedirect.com Procedia Engineering 00 (2013) 000 000 2nd International Symposium on Innovation and Technology in the Phosphate Industry [SYMPHOS 2013] Spray Injectors within

More information

INTERNATIONAL JOURNAL OF DESIGN AND MANUFACTURING TECHNOLOGY (IJDMT) CONSTANT SPEED ENGINE CONROD SOFT VALIDATION & OPTIMIZATION

INTERNATIONAL JOURNAL OF DESIGN AND MANUFACTURING TECHNOLOGY (IJDMT) CONSTANT SPEED ENGINE CONROD SOFT VALIDATION & OPTIMIZATION INTERNATIONAL JOURNAL OF DESIGN AND MANUFACTURING TECHNOLOGY (IJDMT) International Journal of Design and Manufacturing Technology (IJDMT), ISSN 0976 6995(Print), ISSN 0976 6995 (Print) ISSN 0976 7002 (Online)

More information

THE INFLUENCE OF THE MICROGROOVES ON THE HYDRODYNAMIC PRESSURE DISTRIBUTION AND LOAD CARRYING CAPACITY OF THE CONICAL SLIDE BEARING

THE INFLUENCE OF THE MICROGROOVES ON THE HYDRODYNAMIC PRESSURE DISTRIBUTION AND LOAD CARRYING CAPACITY OF THE CONICAL SLIDE BEARING Journal of KONES Powertrain and Transport, Vol. 19, No. 3 2012 THE INFLUENCE OF THE MICROGROOVES ON THE HYDRODYNAMIC PRESSURE DISTRIBUTION AND LOAD CARRYING CAPACITY OF THE CONICAL SLIDE BEARING Adam Czaban

More information

Australian Journal of Basic and Applied Sciences

Australian Journal of Basic and Applied Sciences AENSI Journals Australian Journal of Basic and Applied Sciences ISSN:1991-8178 Journal home page: www.ajbasweb.com Efficient and Environmental Friendly NO x Emission Reduction Design of Aero Engine Gas

More information

New fem model for thermal analysis of medium voltage fuses

New fem model for thermal analysis of medium voltage fuses Technical collection New fem model for thermal analysis of medium voltage fuses 2007 - Conferences publications E. Torres A J. Mazón E. Fernández I. Zamora NEW FEM MODEL FOR THERMAL ANALYSIS OF MEDIUM

More information

Numerical Investigation of the Gas Leakage through the Piston-Cylinder Clearance of Reciprocating Compressors

Numerical Investigation of the Gas Leakage through the Piston-Cylinder Clearance of Reciprocating Compressors Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Numerical Investigation of the Gas Leakage through the Piston-Cylinder Clearance of

More information

AERODYNAMIC DESIGN OPTIMIZATION OF A 200 KW-CLASS RADIAL INFLOW SUPERCRITICAL CARBON DIOXIDE TURBINE

AERODYNAMIC DESIGN OPTIMIZATION OF A 200 KW-CLASS RADIAL INFLOW SUPERCRITICAL CARBON DIOXIDE TURBINE Proceedings of Shanghai 2017 Global Power and Propulsion Forum 30 th October 1 st November, 2017 http://www.gpps.global GPPS-2017-0109 AERODYNAMIC DESIGN OPTIMIZATION OF A 200 KW-CLASS RADIAL INFLOW SUPERCRITICAL

More information

IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 11, 2016 ISSN (online):

IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 11, 2016 ISSN (online): IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 11, 2016 ISSN (online): 2321-0613 Effect of Aspiration Pressure on Convergent Nozzle Employed for Gas Atomization of Liquid

More information

CFD Simulation of a Scroll Compressor Oil Pumping System

CFD Simulation of a Scroll Compressor Oil Pumping System Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2000 CFD Simulation of a Scroll Compressor Oil Pumping System J. de Bernardi Danfoss Maneurop

More information

EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE

EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE Chapter-5 EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE 5.1 Introduction The development of modern airfoil, for their use in wind turbines was initiated in the year 1980. The requirements

More information

ANALYSIS OF BLADES OF AXIAL FLOW FAN USING ANSYS. Mahajan Vandana N.,* Shekhawat Sanjay P.

ANALYSIS OF BLADES OF AXIAL FLOW FAN USING ANSYS. Mahajan Vandana N.,* Shekhawat Sanjay P. Research Article ANALYSIS OF BLADES OF AXIAL FLOW FAN USING ANSYS. Mahajan Vandana N.,* Shekhawat Sanjay P. Address for Correspondence Department of Mechanical Engg. S.S.B.T s College of Engg. and Technology,

More information

INFLUENCE OF TEMPERATURE ON THE PERFORMANCE TOOTHED BELTS BINDER MAGNETIC

INFLUENCE OF TEMPERATURE ON THE PERFORMANCE TOOTHED BELTS BINDER MAGNETIC INFLUENCE OF TEMPERATURE ON THE PERFORMANCE TOOTHED BELTS BINDER MAGNETIC Merghache Sidi Mohammed, Phd Student Ghernaout Med El-Amine, Doctor in industrial automation University of Tlemcen, ETAP laboratory,

More information

Heat Transfer in Rectangular Duct with Inserts of Triangular Duct Plate Fin Array

Heat Transfer in Rectangular Duct with Inserts of Triangular Duct Plate Fin Array Heat Transfer in Rectangular Duct with Inserts of Triangular Duct Plate Fin Array Deepak Kumar Gupta M. E. Scholar, Raipur Institute of Technology, Raipur (C.G.) Abstract: In compact plate fin heat exchanger

More information

Numerical Computation of Flow Field in the Spiral Grooves of Steam Turbine Dry Seal

Numerical Computation of Flow Field in the Spiral Grooves of Steam Turbine Dry Seal American Journal of Aerospace Engineering 2017; 4(5): 54-58 http://www.sciencepublishinggroup.com/j/ajae doi: 10.11648/j.ajae.20170405.11 ISSN: 2376-4813 (Print); ISSN: 2376-4821 (Online) Numerical Computation

More information

Vedant D. Vyas 1, Dr. D. B. Jani. 2 1,2 PG research scholar (CAD/CAM) Mechanical engineering department, GEC-Dahod. IJRASET: All Rights are Reserved

Vedant D. Vyas 1, Dr. D. B. Jani. 2 1,2 PG research scholar (CAD/CAM) Mechanical engineering department, GEC-Dahod. IJRASET: All Rights are Reserved CFD Simulation of Air Flow in CFBC Boiler under Different Geometry of Nozzle Grid Vedant D. Vyas 1, Dr. D. B. Jani. 2 1,2 PG research scholar (CAD/CAM) Mechanical engineering department, GEC-Dahod. Abstract:

More information

Structural Analysis of Pick-Up Truck Chassis using Fem

Structural Analysis of Pick-Up Truck Chassis using Fem International Journal of ChemTech Research CODEN (USA): IJCRGG, ISSN: 0974-4290, ISSN(Online):2455-9555 Vol.9, No.06 pp 384-391, 2016 Structural Analysis of Pick-Up Truck Chassis using Fem Rahul.V 1 *,

More information

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating

More information

Research in hydraulic brake components and operational factors influencing the hysteresis losses

Research in hydraulic brake components and operational factors influencing the hysteresis losses Research in hydraulic brake components and operational factors influencing the hysteresis losses Shreyash Balapure, Shashank James, Prof.Abhijit Getem ¹Student, B.E. Mechanical, GHRCE Nagpur, India, ¹Student,

More information

Vibration Measurement and Noise Control in Planetary Gear Train

Vibration Measurement and Noise Control in Planetary Gear Train Vibration Measurement and Noise Control in Planetary Gear Train A.R.Mokate 1, R.R.Navthar 2 P.G. Student, Department of Mechanical Engineering, PDVVP COE, A. Nagar, Maharashtra, India 1 Assistance Professor,

More information

Driver roll speed influence in Ring Rolling process

Driver roll speed influence in Ring Rolling process Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 207 (2017) 1230 1235 International Conference on the Technology of Plasticity, ICTP 2017, 17-22 September 2017, Cambridge, United

More information

CFD ANALYSIS ON LOUVERED FIN

CFD ANALYSIS ON LOUVERED FIN CFD ANALYSIS ON LOUVERED FIN P.Prasad 1, L.S.V Prasad 2 1Student, M. Tech Thermal Engineering, Andhra University, Visakhapatnam, India 2Professor, Dept. of Mechanical Engineering, Andhra University, Visakhapatnam,

More information

China. Keywords: Electronically controled Braking System, Proportional Relay Valve, Simulation, HIL Test

China. Keywords: Electronically controled Braking System, Proportional Relay Valve, Simulation, HIL Test Applied Mechanics and Materials Online: 2013-10-11 ISSN: 1662-7482, Vol. 437, pp 418-422 doi:10.4028/www.scientific.net/amm.437.418 2013 Trans Tech Publications, Switzerland Simulation and HIL Test for

More information

Harmonic Analysis of Reciprocating Compressor Crankcase Assembly

Harmonic Analysis of Reciprocating Compressor Crankcase Assembly IOSR Journal of Engineering (IOSRJEN) www.iosrjen.org ISSN (e): 2250-3021, ISSN (p): 2278-8719 PP 16-20 Harmonic Analysis of Reciprocating Compressor Crankcase Assembly A. A. Dagwar 1, U. S. Chavan 1,

More information

Optimization of Seat Displacement and Settling Time of Quarter Car Model Vehicle Dynamic System Subjected to Speed Bump

Optimization of Seat Displacement and Settling Time of Quarter Car Model Vehicle Dynamic System Subjected to Speed Bump Research Article International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347-5161 2014 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Optimization

More information

A Method to Define Profile Modification of Spur Gear and Minimize the Transmission Error

A Method to Define Profile Modification of Spur Gear and Minimize the Transmission Error A Method to Define Profile Modification of Spur Gear and Minimize the Transmission Error Authors: Marco Beghini Fabio Presicce Ciro Santus Collaboration between: Mech. Dept. University of Pisa - Italy

More information

inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering August 2000, Nice, FRANCE

inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering August 2000, Nice, FRANCE Copyright SFA - InterNoise 2000 1 inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering 27-30 August 2000, Nice, FRANCE I-INCE Classification: 0.0 EFFECTS OF TRANSVERSE

More information

Influence of Ground Effect on Aerodynamic Performance of Maglev Train

Influence of Ground Effect on Aerodynamic Performance of Maglev Train 2017 2nd International Conference on Industrial Aerodynamics (ICIA 2017) ISBN: 978-1-60595-481-3 Influence of Ground Effect on Aerodynamic Performance of Maglev Train Shi Meng and Dan Zhou ABSTRACT Three-dimensioned

More information