Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.

Size: px

Start display at page:

Download "Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B."

Jewel Horton
5 years ago
Views:

1 «1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept in a clean area. Remove the torque converter, taking care not to spill the transmission fluid. Before disassembly, clean the outer surface of the transaxle by using steam, cleaning fluid, etc. CAUTION: During disassembly, avoid using rags that can leave fabric particles on components as this can block passages and cause valves to stick. Clean the disassembled parts, and clean the oil passages with compressed air and check to be sure they are not clogged. Note: The casings allow separate repairs to be carried out on either the automatic transaxle or the final drive section. When a problem exists that only requires work on one section, separate the transaxle. Cover the section not requiring attention to prevent foreign material from entering the assembly. SPECIAL SERVICE TOOL(S) REQUIRED ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Description Tool Number ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Bench Mounted Holding Fixture T57L-500-B ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Clutch Compressor T87C B ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Stator and Driven Sprocket Bearing Remover T86P A ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Puller T58L-101-B ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Impact Slide Hammer T50T-100-A ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ Driver Handle T80T-4000-W ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.

2 Torque Converter, Oil Pump, Main Control Valve Body and Externally Mounted Controls

3 ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description 1 -- Speedometer Cable Sleeve Bolt 2 17B301 Speedometer Cable Sleeve Speedometer Gear 4 7A020 Fluid Level Indicator 5 -- Oil Filler Tube Bolt 6 7A228 Oil Filler Tube 7 7A103 Oil Pump 8 -- Oil Pump-to-Transaxle Bolts (8 Req'd) 9 -- Check Ball 10 7A286 Case Detent Spring Main Control Valve Body Bolts (9 Req'd)

4 12 -- Transmission Oil Pan Bolts (16 Req'd) 13 7A194 Transmission Fluid Pan 14 7A191 Oil Pan to Case Gasket 15 7A100 Main Control Valve Body 16 7A247 Park/Neutral Position Switch (PNP Switch) 17 7F037 Kickdown Solenoid 18 7A377 Vacuum Throttle Valve Diaphragm 19 7F351 Turbine Shaft Torque Converter 21 7B328 Oil Pump Shaft A -- Tighten to 8-11 N-m (71-97 Lb-In) B -- Tighten to 7-10 N-m (61-87 Lb-In) C -- Tighten to N-m (11-16 Lb-Ft) D -- Tighten to 5-8 N-m (43-69 Lb-In) ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 2. Pull the oil pump shaft (7B328) out of the turbine shaft (7F351). 3. Pull the turbine shaft out of the torque converter stator support. 4. Separate the kickdown solenoid wire from the wiring harness and remove the kickdown solenoid.

5 5. Remove the Park/Neutral Position Switch (PNP switch) (7A247). 6. Remove the vacuum throttle valve diaphragm (7A377) from the transaxle case. If it is difficult to remove, use pliers to grasp the flange. Remove the throttle control valve rod (7A380).

6 7. Remove the oil filler tube bolt securing the oil filler tube (7A228) to the transaxle. Remove the oil filler tube and fluid level indicator (7A020).

7 8. Remove the speedometer cable sleeve bolt securing the speedometer cable sleeve (17B301) and speedometer gear assembly to the transaxle and remove the speedometer cable sleeve and speedometer gear assembly. 9. Remove the 16 transmission oil pan bolts and remove the transmission fluid pan (7A194) from the transaxle. Discard the oil pan to case gasket (7A191). 10. Note: Be careful not to lose the check ball and detent spring (7D017), located in the slotted hole. Remove the nine main control valve body bolts securing the main control valve body (7A100) and filter. Remove the main control valve body from the transaxle. Note the position of each main control valve body bolt for installation reference.

8 11. Position the transaxle with the oil pump end facing down. With a flat-blade screwdriver inserted in the wide slot between the front clutch drum and the sun shell, pry down on the front clutch drum. Do this several times as you rotate the assembly two complete revolutions.

9 12. Measure the direct clutch drum end play by checking the clearance of the small slot between the direct clutch drum tabs and the sun shell slots. Record this measurement for reference upon reassembly. The standard end play is mm ( inch). 13. Remove the oil cooler hose fittings from the oil pump body. 14. Secure the direct clutch in place by tightening the band adjusting stop (7C492).

10 15. Remove the eight oil pump-to-transaxle bolts and note the position of each bolt for installation reference. Remove the oil pump assembly from the transaxle. 16. Place the oil pump assembly on a workbench with the outer surface face down. Hydraulic Apply Devices, Governor Assembly, and Front Planetary Gearset

11 ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description 1 7D028 Servo Piston Spring 2 -- Servo Piston 3 7D027 Intermediate Band Servo Retainer 4 7D064 Sun Shell 5 7D484 Sun Gear Spacer 6 7D063 Sun Gear 7 7A398 Front Planet Carrier 8 -- Front Ring Gear 9 7D029 Band Strut 10 7D034 Intermediate Band Direct Clutch Assembly

12 12 7A360 Forward Clutch Drum 13 7C492 Band Adjusting Stop 14 7Z114 Band Adjusting Stop Nut Governor Cover Bolt (3 Req'd) 16 7A301 Governor Cover 17 7C053 Governor Valve A -- Tighten to N-m (41-59 Lb-Ft) B -- Tighten to 8-11 N-m (71-97 Lb-In) ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 17. Remove the band adjusting stop and band adjusting stop nut (7Z114) from the transaxle case. As the band adjusting stop is removed, retrieve the intermediate band strut from inside the transaxle case. 18. Remove the intermediate band from the transaxle case through the oil pump opening. 19. Remove the direct clutch assembly.

13 20. Remove the forward clutch drum needle bearing located on the forward clutch drum. ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description 1 7D044 Direct Clutch Drum 2 7D029 Intermediate Band Strut 3 7D034 Intermediate Band

14 4 7F374 Forward Clutch Drum Needle Bearing 5 7A360 Forward Clutch Drum ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 21. Remove the front ring gear. 22. Remove the oil pump thrust washer if the thrust washer did not stay with the oil pump. 23. Remove the thrust bearing (7C096) located on the front ring gear. 24. Remove the forward clutch hub assembly. 25. Remove the thrust bearing and sun gear spacer (7D480) from the front planet carrier. ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description 1 7C096 Thrust Bearing 2 7A360 Front Ring Gear

15 3 7D014 Thrust Washer 4 7F374 Front Ring Gear Needle Bearing 5 7A166 Front Planet Carrier Thrust Washer 6 7A398 Front Planet Carrier 7 7D484 Sun Gear Spacer 8 7D063 Sun Gear ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 26. Remove the front planet carrier. 27. Remove the sun gear. 28. Remove the sun gear spacer.

16 29. Remove the sun shell. 30. Remove the sun shell thrust washer and thrust bearing.

17 ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description 1 7C096 Thrust Bearing 2 7D063 Sun Gear 3 7D484 Sun Gear Spacer 4 7D064 Sun Shell 5 7D066 Sun Shell Thrust Washer ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 31. Use a C-clamp and a socket to compress the servo piston into the transaxle case as shown.

18 32. WARNING: TO AVOID PERSONAL INJURY, WEAR EYE PROTECTION DURING THE FOLLOWING PROCEDURE. Use a flat-blade screwdriver to remove the servo piston retaining snap ring (7381). 33. Remove the servo retainer, servo piston and servo piston spring (7D028) by slowly loosening the C-clamp.

19 34. Disassemble the band apply servo by removing the servo piston spring. Remove the servo piston large seal (7D024). Discard the servo piston large seal. 35. Remove the governor cover bolts, governor cover and governor gasket (7B391). Discard the governor gasket. 36. Remove the governor (7C053) from the transaxle case.

20 37. Remove the 12 transaxle case-to-converter housing bolts. 38. Separate the transaxle case from the converter housing using a flat-blade screwdriver to pry the cases apart at the point shown. Remove the transaxle case. 39. Position the converter housing to remove the differential (4026). Internal Linkages, Rear Planetary Gearset and Low/Reverse Clutch

21 ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description 1 -- Drum Hub Assembly 2 7C096 Needle Bearing 3 7A166 Thrust Washer 4 7D171 Low One-Way Clutch Inner Race 5 7D006 Rear Carrier 6 7G347 Retaining Ring 7 7C096 Thrust Bearing

22 8 7D066 Sun Shell Thrust Washer 9 7D483 Low/Reverse Snap Ring 10 7A089 One-Way Clutch 11 7B066 Retaining Plate, One-Way Clutch 12 7A286 Case Detent Spring Detent Check Ball 14 7C493 Manual Control Lever Shaft 15 7F337 Manual Control Lever Shaft Seal 16 7E415 Ferrule 17 7E416 Spring Washer Retaining Pin Circlip 21 7C495 Park Lever Plate Manual Control Lever Nut 23 7A121 Park Actuator Support Park Actuator Lever Pivot Pin 26 7A232 Parking Lever Actuating Rod 27 7A206 Governor Inlet Tube 28 7D499 Governor Outlet Tube 29 7G101 Support Support Retaining Bolt 31 7A256 Manual Control Lever Manual Control Lever Arm 33 7A441 Parking Pawl 34 7D070 Parking Pawl Return Spring 35 7D071 Parking Pawl Shaft 36 7E085 Low/Reverse Clutch Dished Plate 37 7B164 Low/Reverse Clutch External Spline Clutch Plate 38 7B442 Low/Reverse Clutch Internal Spline

23 Clutch Plate 39 7D483(1) Low/Reverse Clutch Pressure Plate Retainer Snap Ring 40 7F341 Low and Reverse Clutch Hub 41 7D402 Low/Reverse Clutch Piston 42 7A548 Reverse Clutch Piston Large Seal 43 7D404 Reverse Clutch Piston Small Seal Manual Shaft O-Ring Manual Control Lever Nut A -- Tighten to N-m (22-29 Lb-Ft) ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ (1) - NOT used when the transaxle is assembled in production, however, it is required in assembly when servicing the transaxle. 40. Place a screwdriver underneath the governor outlet tube (7D469) and governor inlet tube (7A206) and gently pry outward. Remove the governor outlet tube and governor inlet tube. 41. Note the position of the parking pawl return spring (7D070) for installation reference. Remove the parking pawl assembly by pulling the parking pawl shaft (7D071) straight out.

24 42. Remove the drum hub assembly from the transaxle case. 43. Remove the one-way clutch race (7D171) and rear planet carrier from the converter housing. 44. Use a flat-blade screwdriver to remove the low/reverse snap ring from the one-way clutch race.

25 45. Separate the rear planetary carrier from the one-way clutch race. 46. Remove the rear planet carrier to ring gear needle bearing and rear planet carrier to ring gear thrust washer from the rear planet carrier. ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description 1 7D171 One-Way Clutch Race 2 7D006 Rear Planet Carrier

26 3 7G347 Snap Ring 4 7A166 Rear Carrier to Ring Gear Thrust Washer 5 -- Drum Hub Assembly 6 7C096 Rear Carrier to Ring Gear Needle Bearing ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 47. Before removing the one-way clutch (7A089), use a feeler gauge to measure the clearance of the one-way clutch retaining plate and the one-way clutch. The clearance should be mm ( inch). If the clearance is out of specification, adjust it by selecting the proper one-way clutch retaining plate at the time of installation. 48. WARNING: TO AVOID PERSONAL INJURY, WEAR EYE PROTECTION DURING THE FOLLOWING PROCEDURE. Use a flat-blade screwdriver to remove the snap ring securing the one-way clutch and the one-way clutch retaining plate to the transaxle case. Remove the one-way clutch and the one-way clutch retaining plate.

27 49. Remove the low/reverse clutch pack and the low/reverse clutch dished plate. 50. Use Clutch Compressor T87C B to place the recessed side of the large plate over the low and reverse clutch hub (7F341). Place the small plate on the opposite side of the case. Insert the bolt through the clutch compressor plates and tighten the nut until the tension is relieved from the low/reverse snap ring. 51. WARNING: TO AVOID PERSONAL INJURY, WEAR EYE PROTECTION DURING THE FOLLOWING PROCEDURE. Use a flat-blade screwdriver to pry the low/reverse snap ring from the snap ring groove. 52. Remove Clutch Compressor T87C B. 53. Remove the low/reverse clutch hub. 54. Remove the return springs from the low/reverse clutch piston. 55. WARNING: WHEN PERFORMING THE FOLLOWING PROCEDURE, USE CARE TO PROTECT YOURSELF FROM THE FORCE OF THE PISTON. KEEP YOUR FINGERS FROM BETWEEN THE WOOD BLOCK AND THE PISTON. EYE PROTECTION SHOULD ALSO BE USED WHEN PERFORMING THIS OPERATION.

28 To remove the low/reverse clutch piston, hold a wood block over the low/reverse clutch piston and apply a short burst of air pressure (not to exceed 400 kpa [60 psi]) into the low/reverse clutch piston apply port in the transaxle case as shown. 56. Remove the parking pawl actuator support bolts. Remove the parking pawl actuator support. 57. Remove the manual control lever nut at the end of the manual control lever assembly, holding the manual control lever (7A256) with an open-end wrench. 58. Remove the two circlips from the park actuator support (7A121).

29 59. Remove the park lever plate (7C495) and park actuator support from the manual control lever. 60. Remove the two manual control lever support bolts from the manual control lever support and slide the manual control lever out of the transaxle case. 61. Remove the parking lever actuating rod (7A232) and ferrule as an assembly from the transaxle case.

30 62. Position the transaxle with the oil pan opening facing up. Remove the roll pin securing the manual control lever shaft (7C493) to the transaxle case by lightly tapping the roll pin with a 3/32 inch pin punch and a hammer. 63. Carefully slide the manual control lever shaft out of the transaxle case, making sure not to lose the detent ball and case detent spring (7A286). 64. Remove the detent ball.

31 65. Use a small flat-blade screwdriver to remove the case detent spring. Differential, Idler Gear Assembly and Output Shaft

32 ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø Item Part Number Description Differential 2 -- Idler Gear and Idler Gear Shaft 3 -- Idler Gear Shaft Roll Pin 4 -- Bearing Housing Bolt (8 Req'd) 5 -- Bearing Housing (Part of 7005) Output Shaft 7 -- Torque Converter Stator Support Bolt (6 Req'd) 8 7A108 Torque Converter Stator Support Differential Oil Seal A -- Tighten to N-m (14-19 Lb-Ft)

33 B -- Tighten to N-m ( Lb-In) ƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒ ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒÿ 66. Lift the differential out of the converter housing. 67. Remove the idler gear shaft roll pin. Discard the idler gear shaft roll pin. 68. Remove the eight bearing housing bolts attaching the bearing housing to the converter housing.

34 69. Remove the idler gear and output gear assemblies by lightly tapping the idler gear shaft (7F358) with a brass drift and hammer. 70. Use a brass drift and hammer and tap lightly on the idler gear shaft to remove the idler gear and output gear assembly from the bearing housing. 71. Note: Separate or mark each output shaft bearing selective shim (7F405) upon removal for installation reference. Use Stator and Driven Sprocket Bearing Remover T86P A, Puller T58L-101-B, and Impact Slide Hammer T50T-100-A to remove the bearing race from the bearing housing. Remove the output shaft bearing selective shim from the bearing housing.

35 72. Use Puller T58L-101-B, Stator and Driven Sprocket Bearing Remover T86P A, and Impact Slide Hammer T50T-100-A to remove the differential side bearing races from the transaxle case and from the converter housing. Transaxle Case

36 Converter Housing 73. Use a flat-blade screwdriver to remove the differential oil seals. 74. Use Seal Remover TOOL-1175-AC or equivalent, and Impact Slide Hammer T50T-100-A to

37 remove the converter impeller hub seal (7F401) from the torque converter stator support. 75. Use Puller T58L-101-B and Impact Slide Hammer T50T-100-A to remove the output shaft bearing race from the torque converter stator support (still mounted in the converter housing). 76. Remove the six torque converter stator support bolts. 77. CAUTION: Have an assistant hold the torque converter stator support to prevent it from falling on the floor and being damaged. Use the appropriate step plate from Step Plate Adapter Set D80L-630-A or equivalent and Driver

38 Handle T80T-4000-W to remove the torque converter stator support. 78. Refer to «Cleaning and Inspection» for transaxle inspection.

DISASSEMBLY. Transmission. All vehicles

DISASSEMBLY. Transmission. All vehicles 307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 DISASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Remover, Servo 307-347 (T97T-7D021-A)