STANDBY EMERGENCY CNG/LPG GENERATOR
|
|
- Morgan Parks
- 5 years ago
- Views:
Transcription
1 SECTION STANDBY EMERGENCY CNG/LPG GENERATOR PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Compressed natural gas (CNG) or liquefied petroleum gas (LPG) powered standby emergency generators. B. Related Sections: Concrete. 2. Division 15 - Mechanical Ductwork Automatic Transfer Switch Overcurrent Protective Devices SYSTEM DESCRIPTION A. Use of fuel oil system is not allowed SUBMITTALS A. Submit for review, properly identified product data material. B. Provide operating and maintenance manuals complete with replacement parts data for standby emergency generator system. C. Submit sample of written warranty with product data. D. Contract Closeout Submittal: Furnish the Board with manufacturer's certification and warranty assuring each item of equipment is complete and in good condition, free from damage, properly installed, connected, adjusted, and tested as to full power rating, stability, and voltage and frequency regulation QUALITY ASSURANCE A. Qualifications: Single source generator supplier and installer, acceptable to the standby emergency generator manufacturer, capable of providing, but not limited to, the following services: 1. Generator and electrical apparatus pertinent to the generator including the automatic transfer switches. 2. Complete fuel tank system. Project No. SPECIFICATION GUIDELINES
2 3. Sheet metal shrouding. 4. Plumbing pertinent to the fuel system and generator. 5. Exhaust system and piping. 6. Insulation of exhaust system. 7. Control wiring between generator and transfer switch, water heater, battery charging, and annunciator wiring. 8. Required warranty. 9. Other work required for a complete and operable system. B. The Board will not accept 2 or more subcontractors to do the Standby Emergency Generator work. C. Performance Requirements: Materials shall bear Underwriters Laboratories (UL) labels WARRANTY A. Furnish standby emergency generator set completely by manufacturer and warranted for a period of 5 years from date of substantial completion. PART 2 PRODUCTS 2.01 MANUFACTURERS A. Standby Electric Generator System: 1. Caterpillar. 2. Kohler. 3. Onan EQUIPMENT NOTE TO SPECIFIER: In the following sentence, specify the voltage requirements to suit project conditions. A. Standby Emergency Generator: Include an electric generator set rated for continuous standby service. B. Emergency Generator Fuel Tanks: Pressurized with uninterrupted, on-site, local fuel, such as CNG or LPG tanks. C. System shall be a package of new and current equipment consisting of: 1. A natural gas or electric engine driven generating set Project No. SPECIFICATION GUIDELINES
3 to provide standby power. 2. An engine start-stop control system. 3. An automatic load transfer control to provide automatic starting and stopping of the engine and switching of the load as specified in Section Mounted accessories as specified. D. The system shall be built, tested, and shipped by the manufacturer of the alternator so there is one source of supply and responsibility. The performance of this generating set series shall be certified by an independent testing laboratory as to the set's full power rating, stability and voltage and frequency regulation. NOTE TO SPECIFIER: The A/E shall provide the project specific information regarding engine performance requirements to suit project conditions. E. Engine: F. Engine Instrument Panel: G. Engine Controls: H. Alternator: Provide overcurrent protection on generator. I. Unit Performance: J. Alternator Instrument Panel: Wire, test, and shock mount on the generating set by the manufacturers of the alternator. It shall contain panel lighting, manual reset circuit breaker, frequency meter, running time meter, voltage adjusting rheostat, AC voltmeter (dual range, indicates all voltages), AC ammeter (dual range, indicates current in each phase), meter switch, voltmeter-ammeter phase selector with OFF position. K. Generator Mounting: 1. Concrete Pad: Provide a 6 inch high concrete pad under each emergency generator. 2. Equip with vibration isolators and mount on a welded steel base that shall provide suitable mounting to any level surface. L. Automatic Load Transfer Control: Complete automatic transfer switch shall be supplied by manufacturer of alternator. It shall include necessary relays and component Project No. SPECIFICATION GUIDELINES
4 parts, with electrically and mechanically interlocked switches. See Section M. Accessories: Furnish accessories needed for the proper operation of the generating set. These shall include but not be limited to an exhaust muffler, flexible exhaust connection, starting batteries, battery cables, battery charger, battery rack, fuel oil day tank, and fuel lines. 1. Exhaust Muffler: All-welded design, constructed of sheet and plate steel. Provide with all necessary flexible exhaust connections as indicated on mechanical drawings for installation by mechanical contractor. Exhaust muffler manufacture: Maxim M-41 with side inlet or accepted equivalent. 2. Insulation: The muffler and all indoor exhaust piping shall be properly lagged using Kaylo 1800 degree F. insulation. Insulation will be furnished and installed under the insulation section. 3. Jacket water heater shall be installed inline with engine cooling system. Jacket water heater to be rated at 2 KW, at application voltage, single phase. PART 3 EXECUTION 3.01 INSTALLATION A. Install standby emergency generator according to the manufacturer's recommendations and according to the requirements of NFPA 70 - National Electrical Code (NEC). 1. The following items of work relating to the emergency generators will be provided under other sections by different trades. a. Fuel System including main fuel oil storage tank, (day tanks), and piping, as specified. b. Cooling air intake and exhaust louvers. c. Sheetmetal ductwork interconnection between radiator and exhaust air louvers. d. Installation of mufflers and exhaust pipes and insulation of same. 2. The Installer shall be responsible for coordinating all trades to ensure the proper functioning of the entire systems including but not limited to fuel supply, exhaust equipment and air transfer system. This coordination shall include furnishing all required Project No. SPECIFICATION GUIDELINES
5 information to other subcontractors regarding fuel, exhaust and cooling system dimensions, pipe and duct sizes, etc. The Installer shall furnish a dimensioned plan layout indicating all generator dimensions, roughing dimensions, piping layout, duct layout, tank locations and elevations and all required electrical wiring and interconnections TESTS AND START-UP A. Tests: 1. The electric generator set shall receive the manufacturer's standard testing. 2. Before acceptance of the installation, the equipment shall be tested to show it will start automatically, subjected to full load test or that load available at the job-site, shut down and reset as required in these Specifications. 3. Before acceptance, any defects that become evident during this test shall be corrected at no additional cost to the Board. B. Start-up and Instructions: 1. On completion of the installation, perform the initial start-up by a factory-trained representative of the engine supplier. 2. At the time of start-up, operating instructions and maintenance procedures shall be thoroughly explained to operating personnel. 3. Two copies of operating and maintenance instruction books shall be supplied for the electric set and such auxiliary equipment as may require same. END OF SECTION Project No. SPECIFICATION GUIDELINES
************************************************************************************************************* PART 1 GENERAL 1.
16620 STANDBY EMERGENCY ELECTRICAL GENERATOR (CNG/LPG) ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number:
More information.3 Section Concrete Forms and Accessories: Installation of Anchor Devices, Setting Templates
Issued 2005/06/01 Section 16239 Power Generation to 30 kw Page 1 of 7 PART 1 GENERAL 1.1 RELATED WORK.1 Section 01355 Waste Management and Disposal..2 Section 01810 Commissioning..3 Section 03100 Concrete
More informationEMERGENCY GENERATOR SET
PART 8.1: EMERGENCY GENERATOR SET PART 1 - GENERAL I SCOPE A. This specification covers the design, furnishing, installation and start up of a factory built, production tested, operable, liquid cooled
More informationUniversity of Houston Master Construction Specifications Insert Project Name
SECTION 26 13 13 MEDIUM VOLTAGE SWITCHGEAR PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 263213 - ENGINE GENERATORS PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 22 1123.13 DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More information1. Division 26 Section "Elevator Shunt-Trip Fused Disconnect Switches".
SECTION 26 28 16 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections,
More informationSPECIAL SPECIFICATION 5066 Packaged Engine Generator System
2004 Specifications CSJ 2121-04-072 SPECIAL SPECIFICATION 5066 Packaged Engine Generator System 1. Description. Furnish and install packaged engine generator system complete with transfer switch and service
More informationSECTION AXIAL HVAC FANS
SECTION 233413 - AXIAL HVAC FANS 1. PART 1 GENERAL 1.1. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION ENCLOSED SWITCHES AND CIRCUIT BREAKERS
SECTION 26 28 16 ENCLOSED SWITCHES AND PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following individually mounted, enclosed switches and circuit breakers rated 600V AC and less: 1. Fusible switches.
More information1510 GENERATOR AND TRANSFER SWITCHES
SECTION 263216-GENERATOR AND TRANSFER SWITCHES PART 1 GENERAL 1.1 RELATED DOCUMENTS 1.2 INTENT 1.3 STANDBY A. Drawings and provisions of the "General Conditions" and "Special Requirements" and other Division
More informationIN2 Enclosed Switches and Circuit Breakers
Illinois Math and Science Academy DigitalCommons@IMSA Project Manuals IN2 2015 IN2 Enclosed Switches and Circuit Breakers Illinois Mathematics and Science Academy Follow this and additional works at: http://digitalcommons.imsa.edu/facility_in2_manuals
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationA. This Section includes Low Voltage Switchgear Work, as indicated on the drawings, and as specified herein.
16425 SWITCHBOARD ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 26 24 13 An optional keynote to
More informationIce Rink Renovation & New Clubhouse
SECTION 262913 - ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationB. Fabricate in accordance with ASHRAE handbooks and SMACNA duct manuals. A. Submit in accordance with Division-1 and Section
SECTION 15910 DUCT ACCESSORIES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract including General and Supplementary Conditions, Division-1 Specification Sections,
More informationQuik-Spec Coordination Panelboard Specifications
Quik-Spec Coordination Panelboard Specifications 30A - 400A Fusible Panelboards SECTION 26 24 XX (This Specification references CSI MasterFormat 2004) FUSIBLE BRANCH CIRCUIT PANELBOARDS PART 1 1.01 SUMMARY
More informationProduct Specification Guide Expansion and Deflection Couplings. SECTION Raceway and Boxes for Electrical Systems
Product Specification Guide Expansion and Deflection Couplings SECTION 26 05 33 Raceway and Boxes for Electrical Systems Specifier Notes: Delete any information below in Parts 1, 2 or 3 which is not required
More informationA. Equipment shall comply with applicable sections of the latest edition of the following standards:
SECTION 26 32 13 STANDBY GENERATOR SETS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationD. Operation and Maintenance Data. In addition to items specified in Division 1 Section "Operation and Maintenance Data," include the following:
SECTION 16211 - ELECTRICITY METERING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationMedium Voltage Standby non-paralleling Control GUIDE FORM SPECIFICATION
Medium Voltage Standby non-paralleling Control 1. GENERAL GUIDE FORM SPECIFICATION A. The requirements of the contract, Division 1, and part 16 apply to work in this section. 1.01 SECTIONS INCLUDE A. Medium
More informationUniversity of Delaware
SECTION 23 36 00 _ SUMMARY PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Constant/Variable volume supply terminal units. 2. Fan powered terminal units. 3. Exhaust valves B. Related Sections: Section
More informationA. Submit manufacturer's literature and technical data before starting work.
SECTION 16425 SWITCHBOARD PART 1 GENERAL 1.01 SUMMARY A. Related Section: 1. 16450 - Grounding. 1.02 SUBMITTALS A. Submit manufacturer's literature and technical data before starting work. B. Submit Shop
More informationA. This Section includes ac, enclosed controllers rated 600 V and less, of the following types:
SECTION 262913 600 VOLT ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 0 Specification
More informationVERTICAL LIFT FIRE/BLAST DOORS
International Door, Inc. 8001 Ronda Drive Canton, MI 48187 (800) 231-9521 Website: www.international-door.com Sales Dept. E-Mail: sales@international-door.com Engineering Dept. E-Mail: engineering@international-door.com
More informationSECTION CENTRIFUGAL HVAC FANS
SECTION 233416 - CENTRIFUGAL HVAC FANS 1. PART 1 GENERAL 1.1. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationENGINEERING MANUAL PRESSURE STEAM HUMIDIFIERS
Ogdensburg, New York, U.S.A. 1-866-NORTEC-1 Ottawa, Ontario, Canada 1-866-NORTEC-1 ENGINEERING MANUAL PRESSURE STEAM HUMIDIFIERS The LS Series is a cost effective way to provide precise humidity control,
More informationSECTION HVAC CONTROL SYSTEM PART 1 GENERAL 1.01 SUMMARY. A. Section Includes:
SECTION 15970 HVAC CONTROL SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Thermostats, temperature transmitters, controllers, automatic valves, dampers, damper operators, pneumatic/ electric
More informationSECTION WELDING FUME EXHAUST SYSTEM
SECTION 233500 WELDING FUME EXHAUST SYSTEM PART 1 - GENERAL 1.1 WORK INCLUDES Welding fume exhaust system and controls Accessories Additional System Equipment Engineering Support Commissioning 1.2 RELATED
More informationLINCOLN COUNTY STANDARD SPECIFICATIONS SECTION PACKAGED ENGINE GENERATORS, DIESEL
LINCOLN COUNTY STANDARD SPECIFICATIONS SECTION 16231 PACKAGED ENGINE GENERATORS, DIESEL 1.1 General Requirements It is the intent of this specification to secure emergency standby generators that have
More informationSECTION ENCLOSED CONTROLLERS
SECTION 16420 ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationUniversity of Houston Master Construction Specifications Insert Project Name SECTION ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL
SECTION 23 04 10 ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section
More informationDESIGN GUIDELINES LOW VOLTAGE SWITCHGEAR PAGE 1 of 5
DESIGN GUIDELINES LOW VOLTAGE SWITCHGEAR PAGE 1 of 5 1.1. APPLICABLE PUBLICATIONS 1.1.1. Publications listed below (including amendments, addenda, revisions, supplements, and errata), form a part of this
More informationSECTION ENCLOSED SWITCHES AND CIRCUIT BREAKERS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 29 21 ENCLOSED SWITCHES AND CIRCUIT BREAKERS SPEC WRITE NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not
More informationMECHANICAL AND ELECTRICAL COORDINATION SECTION MECHANICAL AND ELECTRICAL COORDINATION PART 1 - GENERAL
13686.00 MECHANICAL AND ELECTRICAL COORDINATION 230002-1 SECTION 230002 MECHANICAL AND ELECTRICAL COORDINATION 1.1 WORK INCLUDED PART 1 - GENERAL A. Work Included in This Section: Materials, equipment,
More informationSECTION ENGINE GENERATORS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 32 13 ENGINE GENERATORS A. This section specifies the furnishing, installation, connection, and testing of the 480v, 3 phase, 3 wire, 125eKW, 156KVA engine standby
More informationATTACHMENT A PRINCE EDWARD COUNTY INVITATION FOR BIDS # MOBILE DIESEL PACKAGED ENGINE GENERATOR SPECIFICATIONS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2
More informationA. Provide a complete system of overcurrent protective devises as indicated on the drawings, and as specified herein.
16475 OVERCURRENT PROTECTIVE DEVICES ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 26 28 16 An optional
More informationMEDIUM-VOLTAGE SWITCHGEAR
REVISION RECORD SECTION 16341 Medium-Voltage Switchgear REV DATE PAGE PARA NO. DESCRIPTION APPROVED BY 28SEP01 ALL Initial issue. 1 29SEP03 ALL General update with miscellaneous changes in entire document.
More informationSECTION ENGINE GENERATORS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 32 13 ENGINE GENERATORS SPEC WRITER NOTE: Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable in the
More informationSECTION AIR TERMINAL UNITS
SECTION 23 36 00 AIR TERMINAL UNITS PART 1 - GENERAL 1.1 SUMMARY A. Section includes constant volume terminal units, variable volume terminal units, dual duct terminal units, fan powered terminal units,
More informationSECTION DC POWER SUPPLY/BATTERY CHARGER
SECTION 26 33 05 PART 1 - GENERAL 1.1 THE REQUIREMENT A. The CONTRACTOR shall provide the single-phase heavy-duty industrial battery charger and all accessories required, complete and operable, in accordance
More informationSECTION EMERGENCY STANDBY POWER SYSTEM
PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall provide, install, and acceptance test a complete and operable emergency standby electric generating system, including all devices and equipment
More informationA. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems.
SECTION 220523 - PLUMBING VALVES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball valves. 2. Butterfly valves. 3. Swing check valves. 4. Spring loaded check valves. 5. Water pressure reducing
More informationSPECIAL SPECIFICATION 8334 Packaged Engine Generator
2004 Specifications CSJ 0196-07-027 SPECIAL SPECIFICATION 8334 Packaged Engine Generator 1. Description. Furnish and install packaged engine-generator of the types and ratings shown on the plans. Where
More informationSECTION (15444) - DOMESTIC WATER PACKAGED BOOSTER PUMPS
SECTION 22 11 23.13 (15444) - DOMESTIC WATER PACKAGED BOOSTER PUMPS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Packaged Domestic Water Booster Pumps B. Related Sections: 1.02 REFERENCES 1. Section
More informationBID SPECIFICATIONS FOR (1) 300kW STANDBY GENERATOR
BID SPECIFICATIONS FOR (1) 300kW STANDBY GENERATOR Bid Specifications for 300 kw Standby Generator Compliance CITY OF GENEVA PUBLIC WORKS DEPARTMENT ENGINE In-Line Six Cylinder, turbocharged ATAAC aspirated,
More informationDIVISION 26 ELECTRICAL SECTION CIRCUIT BREAKERS
DIVISION 26 ELECTRICAL SECTION 26 28 19 PART 1 GENERAL 1.01 DESCRIPTION A. Furnish and install circuit breakers in switchboards, distribution panelboards, and separate enclosures for overcurrent protection
More information1. The term "withstand" means "the unit will remain in place without separation of any parts from the device when subjected to the seismic forces.
SECTION 262816 - ENCLOSED SWITCHES AND CIRCUIT BREAKERS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Fusible switches. 2. Nonfusible switches. 3. Receptacle switches. 4. Shunt trip switches. 5.
More informationNote: All items shown in red require review, and possible input, for information required that is specific to the generator system being specified.
DIVISON 16 ELECTRICAL Section 16620A Diesel Engine Generator Set Note: All items shown in red require review, and possible input, for information required that is specific to the generator system being
More informationSECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY
SECTION 230533 - PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Static pressure
More informationSECTION ENGINE GENERATORS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 32 13 SPEC WRITER NOTE: Use this section lonely for NCA projects. Delete between //----// if not applicable to project. Also, delete any other item or paragraph
More informationSECTION GENERAL-SERVICE AIR COMPRESSOR PART 1 - GENERAL
13686.00 GENERAL SERVICE AIR COMPRESSOR 221519-1 SECTION 22 1519 - GENERAL-SERVICE AIR COMPRESSOR 1.1 RELATED DOCUMENTS PART 1 - GENERAL A. Drawings and general provisions of the Contract, including General
More informationBUSWAY Low Voltage (Pow-R-Flex)
BUSWAY LOW VOLTAGE (POW-R-FLEX) PART 1 GENERAL 1.01 1.02 SCOPE The Contractor shall furnish and install the busway system including all necessary fittings, hangers and accessories as specified herein and
More informationSECTION MOTOR CONTROLLERS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 29 11 SPEC WRITER NOTE: Use this section only for NCA projects. Delete between // ---- // if not applicable to project. Also, delete any other item or paragraph
More informationSECTION MOTOR CONTROLLERS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 29 11 MOTOR CONTROLLERS SPEC WRITER NOTE: Delete between // ---- // if not applicable to project. Also, delete any other item or paragraph not applicable to
More informationMichigan State University Construction Standards SECONDARY UNIT SUBSTATIONS PAGE
PAGE 261116-1 SECTION 261116 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSTANDBY 200 ekw 250 kva
DIESEL GENERATOR SET STANDBY 200 ekw 250 kva Image shown may not reflect actual package. Caterpillar is leading the power generation marketplace with Power Solutions engineered to deliver unmatched flexibility,
More informationSTATEMENT OF WORK. Sinnemahoning State Park Cameron County, Pennsylvania
STATEMENT OF WORK Purchase of One (1) LP Gas (Propane) Standby Generator Set and One (1) Service Entrance Rated Automatic Transfer Switch For Delivery to Visitors Center Sinnemahoning State Park Cameron
More informationSOUND-RETARDANT- VERTICAL LIFT DOORS
International Door, Inc. 8001 Ronda Drive Canton, MI 48187 (800) 231-9521 Website: www.international-door.com Sales Dept. E-Mail: sales@international-door.com Engineering Dept. E-Mail: engineering@international-door.com
More informationSECTION DUCTWORK ACCESSORIES
SECTION 15910 DUCTWORK ACCESSORIES PART 1- GENERAL SCOPE This sections includes accessories used in the installation of duct systems. Included are the following topics: PART 1- GENERAL Related Work Reference
More informationPROJ. NO SECTION HYDRONIC PUMPS
SECTION 23 21 23 HYDRONIC PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 23 2123 - PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationDISCONNECT SWITCH REQUIREMENTS FOR DISTRIBUTED GENERATION CUSTOMERS
Prepared by: SXZO DISCONNECT SWITCH REQUIREENTS FOR DISTRIBUTED GENERATION CUSTOERS 060559 Department: Electric Distribution Section: Design and Construction Approved by: D.Jantz (DWJ7) Date: 8/15/17 Rev.
More informationA. Products shall be designed, manufactured, tested, and installed in compliance with the following standards:
SECTION 26 29 13 ENCLOSED MOTOR CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationOptimizing Emergency Power Systems for Health Care Applications
2018 Annual Conference Optimizing Emergency Power Systems for Health Care Applications aka: Using the latest code changes to improve system reliability and maybe even save some $$$... Overview Michigan
More informationRotary Disconnect Switches, Bulletin 194R
ROCKWELL AUTOMATION PROCUREMENT SPECIFICATION PROCUREMENT SPECIFICATION Rotary Disconnect Switches Bulletin 194R NOTICE: The specification guidelines in this document are intended to aid in the specification
More informationPROJ. NO SECTION PACKAGED, OUTDOOR, CENTRAL-STATION AIR-HANDLING UNITS
SECTION 23 74 13 PACKAGED, OUTDOOR, CENTRAL-STATION AIR-HANDLING UNITS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationCity of Storm Lake Fire Department Heavy Rescue Specifications
INTENT OF SPECIFICATIONS City of Storm Lake Fire Department Heavy Rescue Specifications It shall be the intent of these specifications to provide a complete apparatus equipped as hereinafter specified.
More informationSTANDBY 40 ekw 40 kva PRIME 36 ekw 36 kva
DIESEL GENERATOR SET FEATURES Image shown may not reflect actual package. STANDBY 40 ekw 40 kva PRIME 36 ekw 36 kva Caterpillar is leading the power generation marketplace with Power Solutions engineered
More informationA. Work Included: Provide low voltage switchboard work as shown, scheduled, indicated, and as specified.
SECTION 26 24 13 LOW VOLTAGE SWITCHBOARDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationSTANDBY 80 ekw 100 kva PRIME 72 ekw 90 kva
DIESEL GENERATOR SET FEATURES Image shown may not reflect actual package. STANDBY 80 ekw 100 kva PRIME 72 ekw 90 kva Caterpillar is leading the power generation marketplace with Power Solutions engineered
More informationSECTION STANDBY GENERATOR
SECTION 26 32 13 STANDBY GENERATOR PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Specification Sections,
More informationSTANDBY 200 ekw 250 kva
DIESEL GENERATOR SET STANDBY 200 ekw 250 kva Caterpillar is leading the power generation marketplace with Power Solutions engineered Image shown may not reflect actual package reliability, and cost-effectiveness.
More informationSECTION HYDRAULIC FOUR FOLD DOORS MODEL 48 LOUVERS
SECTION 08350 HYDRAULIC FOUR FOLD DOORS MODEL 48 LOUVERS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1
More informationSECTION SWITCHGEAR. A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section.
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes metal-enclosed,
More informationEast Central College
SECTION 262726 - WIRING DEVICES PART 1 - GENERAL 1.1 WORK INCLUDES A. Base and Alternate Bids: 1. Contractor Provide: a. Wall switches. b. Receptacles c. Device plates and decorative box covers. 1.2 RELATED
More informationSECTION COMPRESSED-AIR PIPING FOR LABORATORY FACILITIES
Page 226113-1 SECTION 226113 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationStandby Power Systems
Source: Power Quality in Electrical Systems Chapter 13 Standby Power Systems The term standby power systems describes the equipment interposed between the utility power source and the electrical load to
More informationLow Voltage Automatic Transfer Switch Systems
Suitable for Emergency, Peak and Prime Power System Applications Low Voltage Automatic Transfer Switch Systems THE POWER AUTHORITY THE POWER AUTHORITY ASCO s experience and commitment to excellence in
More informationRPS Station. Solutions for the North American Solar Market
RPS Station Solutions for the North American Solar Market 2013/2014 Power, control and green solutions 3 RPS Station s RPS Station is a fully integrated photovoltaic power conversion system that is designed
More informationDefender Mini Online Emergency Central Lighting Inverter (CLI) Technical Specifications
Defender Mini Online Emergency Central Lighting Inverter (CLI) Technical Specifications PART 1 GENERAL 1.1 SUMMARY A. The Defender Mini CLI specification describes a single phase, online, solid state Lighting
More informationSECTION PACKAGED ENGINE GENERATOR SYSTEMS
PROJECT: SECTION 16620 PACKAGED ENGINE GENERATOR SYSTEMS PART 1 GENERAL 1.1 SUMMARY: A. This Section includes packaged engine-generator systems for emergency power supply with the following features: 1.
More information2018 Consultant s Handbook Division 26 Electrical 2413 Switchboards
1 General 1.1 Switchboards shall be U.L. listed and labeled. 1.2 Each switchboard shall have its own main disconnecting means unless it is located in the same room as its source of origin. In most cases
More information3. Customer shall provide space for metering equipment and meter base as per Springville City Power requirements.
A. General This Customer-Owned Generation Standards for Customer-Owned Grid Connected Electric Generating Systems sets forth the requirements and conditions for interconnected non-utility-owned electric
More informationIlluminator Series CR NEMA 3R
Illuminator Series CR NEMA 3R GUIDE SPECIFICATIONS And TECHNICAL DESCRIPTION For 3.0, 4.0, 5.0, 6.5, 8.0kVA / kw Series CR - Single Phase Uninterruptible Power System This description contains all the
More informationREQUIREMENTS FOR PARALLEL OPERATION FOR CUSTOMERS WITH GENERATION NOT EXCEEDING 50 kw
REQUIREMENTS FOR PARALLEL OPERATION FOR CUSTOMERS WITH GENERATION NOT EXCEEDG 50 kw FOREWARD Requirements for Parallel Operations for Customers with Generation Not Exceeding 50 kw is intended to be used
More informationSection SWITCHBOARDS. Introduction. Part 1 - General. Related Work
Section 16435 - SWITCHBOARDS Introduction Part 1 - General Related Work Section 16070 Seismic Anchorage and Restraint Section 16075 Electrical Identification Section 16080 Power Distribution Acceptance
More informationDER Commissioning Guidelines Community Scale PV Generation Interconnected Using Xcel Energy s Minnesota Section 10 Tariff Version 1.
Community Scale PV Generation Interconnected Using Xcel Energy s Minnesota Section 10 Tariff Version 1.3, 5/16/18 1.0 Scope This document is currently limited in scope to inverter interfaced PV installations
More informationSECTION MOTOR CONTROL
SECTION 26 24 19 MOTOR CONTROL PART 1 - GENERAL 1.1 SECTION INCLUDES A. Manual motor starters B. Magnetic motor starters C. Combination magnetic motor starters D. Solid-state reduced voltage motor starters
More informationDENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION MOTORS, STARTERS & DRIVES
PART 0 DESIGN STANDARDS 0.01 GENERAL DESIGN GUIDELINES A. Coordinate starter needs for mechanical equipment prior to 50% CD and confirm again for 100% CD submittal. B. Coordinate temperature controls requirements
More informationAir Handling Unit Construction Checklist
Air Handling Unit Construction Checklist Project: Date: AHU Tag: Location: Submittal / Approvals Submittal. The above equipment and systems integral to them are complete and ready for functional testing.
More informationSUBSTATION VACUUM CIRCUIT BREAKER (15.5KV)
SUBSTATION VACUUM CIRCUIT BREAKER (15.5KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities
More informationSUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV)
SUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products
More informationSUBSTATION VACUUM CIRCUIT BREAKER (38KV)
SUBSTATION VACUUM CIRCUIT BREAKER (38KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities
More informationFortress 1 Outdoor Emergency Central Lighting Inverter (CLI) Technical Specifications
Fortress 1 Outdoor Emergency Central Lighting Inverter (CLI) Technical Specifications PART 1 GENERAL 1.1 SUMMARY A. This specification describes a single phase, on-line, double conversion, solid state
More informationThis Manu-Spec specifies automatic swinging gate operators and accessories for residential, commercial, and industrial use GATE OPERATORS
7820 Gloria Avenue Van Nuys, California, 91406 Phone: (818) 787-1988 FAX: (818) 787-2214 Email: info@allomatic.net Website: allomatic.net This Manu-Spec utilizes the Construction Specifications Institute
More informationCLIENT: PROJECT: PO#: ESTIMATOR:
GENERATOR CONTROL DATA SHEET CLIENT: PROJECT: PO#: ESTIMATOR: PRIME MOVER FUEL: RPM: GOVERNOR SPEED ADJUST RHEOSTAT SUPPLIED WITH GOVERNOR: LOAD SHARING: REMOTE: PRIME MOVER PROTECTION LOW OIL PRESSURE
More information1500 or 1800 RPM. Engine Specifications C18 ATAAC, I-6, 4-Stroke Water-Cooled Diesel 145 mm (5.71 in) 183 mm (7.2 in) Compression Ratio 14.
Caterpillar is leading the power generation marketplace with Power Solutions engineered to deliver unmatched flexibility, expandability, reliability, and cost-effectiveness. Specifications Generator Set
More information