Driver & Stepping motor package CSA Series. Operation Manual

Size: px
Start display at page:

Download "Driver & Stepping motor package CSA Series. Operation Manual"

Transcription

1 Driver & Stepping motor package CSA Series CSA BX Operation Manual (Ver.3) 2012.Feb. RoHS compliant This operation manual describes product handling procedures and important information to use of product. Be sure to read this operation manual for safe operation before using/ Keep this manual near at hand after reading. Table of content Handling precaution for safe use Before using product 3 2. Product overview Product features and main functions Product lineup 4 3. Preparation & installation Unpack & check Name & function Power supply preparation Installing locations Installing method & precaution Cable & Connection with driver Connection with peripherals Switch setting Operation Timing chart LED Protective functions / Alarms General specifications Troubleshooting & countermeasure Periodical inspection Warranty Notes 30

2 Handling precaution for safe use Warning Handling the product breaching this 'warning' notice may cause critical accidents such as serious injuries or even death. Do not use the product under explosive or flammable environmental condition. It may cause fires or injuries. Installation, connection, operation, control and inspection must be done by only qualified personnel, Done only by unqualified personnel may cause fires or injuries. Connect the cable securely under this operation manual. Miss connection or improper connection may cause fires. Turn off the power supply of the application in the invent of the electricity failure. Sudden restarting of motor when power is restored may cause injuries or equipment damages. Turn off the power supply of the application when motor is exposed water splash. Operation under wet condition may cause fires. Do not disassemble or modify the motor. It may cause fires. Contact sales agent or sales office if the internal inspection or repair is required. Keep motor surface temperature 70 deg.c (158 deg.f) or lower. Excessive temperature rise may cause fires or injuries. Keep the motor away from inflammable goods. Improper motor installation may cause fires. Stop operation immediately and turn off the motor power supply, if unexpected system malfunction occurs. Otherwise, it may cause fires or injuries. Caution Handling the product breaching this 'Caution' notice may cause injuries or property damages. Be careful for the static electricity for the motor handing. Touching by electrified fingers may cause the motor damage. Do not use the motor beyond the motor specifications. It may cause property damages. Do not plug or unplug the connector during the power supply is turned on. It may cause electric shocks or property damages. Do not touch the motor output shaft (Rotating portion) during the operation. It may cause injuries. Do not touch the motor surface during the operation or even immediate after the operation. The motor surface temperature does not go down so quickly. it may cause burns. Equip external safety devices or emergency stop circuits for the case of application system failures or unexpected system malfunctions. Dispose the motor as industrial waste, if necessary. 2

3 1. Before using product < Before starting > This product described here is designed and manufactured for the use in general industrial machinery, including built in applications such as following Suggested applications. Note the product warranty policy does not apply and is void when product is used in the following None suggested applications. Suggested applications General industrial machinery including built in applications such as automatic assembling machines, machining fixture, inspection machines, factory automation machines. None suggested applications Applications that may significantly affect human lives or properties, such as safety devices, transportation equipment (including automobiles, automotive devices, aerospace and ships), medical devices, home-use electric or electronic appliances. 2. Product overview 2-1. Product features and main functions < Product features > This product is unique stepping motor and driver package that has open-loop stall detection mode and closed-loop operation mode. In open-loop stall detection mode, the motor run at open-loop condition and output alarm when motor stalls. In closed-loop mode, the motor keeps running and trace pulse order without stalling even when the motor like to lose synchronization to the input pulse by excessive acceleration order or impermanent overload beyond the motor performance. Also velocity filter can minimize vibration and achieve smooth drive during acceleration and deceleration. <Main functions> 2 type of motor operation modes for different application and situation Open-loop stall detection mode Closed-loop operation mode Smooth acceleration and deceleration with velocity filter Selectable in 4 steps resolution setting : 400, 800, 1600, 3200 PPR DC24V input and 13 steps current setting : A Protective function : Overheat, excessive regenerative voltage, low voltage, excessive load and excessive velocity Automatic power down function 3

4 2.2 Product lineup < Standard model > Item name Motor name Driver name CSA-BX42D2E PMSB-B42D2E CSA-BX42D4E PMSB-B42D4E CSA-BX56D1E PMSB-B56D1E CSA-BX56D3E PMSB-B56D3E CSA-BX56D5E PMSB-B56D5E PDSA-BX < Geared model > Item name Motor name Driver name CSA-BX42D2ESD PMSB-B42D2ESD CSA-BX56D1ESD PMSB-B56D1ESD PDSA-BX 3. Preparation & installation 3-1. Unpack & check Unpack and check the following items. 1.Motor driver (PDSA-BX) 1 2.Motor (PMSB Series) 1 3.Motor to Driver cable (60cm) 1 4.Driver signal cable (60cm) 1 5.Driver power cable (60cm) 1 6.Operation manual (This document) 1 Contact sales agent you purchased from or sales office if any missing or damage. 4

5 3.2 Name and function Motor PMSB-B42D E PMSB-B56D E PMSB-B42D2ESD PMSB-B56D1ESD Item name 1 Mounting pilot 2 Output shaft 3 Motor connector 4 Motor mounting holes (4holes) Description Pilot for positioning motor mount Rotating motor shaft (with flat) Mating connector for motor cable Hole for motor mounting 5

6 Driver PDSA-BX 6 3 Item name 1 Power cable connector (CN1) 2 Signal cable connector (CN2) 3 Motor cable connector (CN3) 4 DIP switch (SW1) 5 Rotary switch (SW2) 6 LED indicator 7 Mounting plate Description Mating connector for DC24V power supply cable connection M a t i n g c o n n e c t o r f o r s i g n a l c a b l e connection M a t i n g c o n n e c t o r f o r m o t o r c a b l e connection DIP switch for driver function setting Rotary switch for driving current setting 2 indicators for driver condition (POWER and ALARM) Mounting plate of driver (Working as heat dissipation) 6

7 3-3. Power supply preparation Prepare enough current capacity power supply referring the following chart. Input power supply voltage DC24V ± 10% Input power supply current capacity Enough capacity to supply current to the motor driving Minimum 3.0A power supply is recommended, when the motor size and motor driving current is not determined. Power supply that endures the inductive load is recommended, as the motor regenerates the current to the power supply. Using less capable power supply may cause unexpected motor malfunction such as unstable operation at high speed running or slow starting up time Installing locations This product is designed and manufactured for the use in general industrial machinery including built in applications. Installation must be under the following conditions. Indoor. No presence of evaporative, flammable or corrosive gas. Ambient temperature 0 to 40 Deg. C (32 to 104 Deg. F). Ambient humidity 85% or less (No freezing or condensing). No water and oil splash. No excessive dust or metal particle surroundings. Free from continuous mechanical vibration or excessive external impact. Location can be expected proper metallic heat dissipation. Free from excessive electromagnetic noise area. Ventilated and accessible area for periodical inspection. 7

8 3-5. Installing method & precaution No restriction of the motor installing orientation. Fit motor pilot for mounting plate hole. Mount the motor on appropriate flat metal plate that can be expected good isolation from vibration and good heat dissipation. Fix securely with 4 screws (or 4 bolts). Keep on gap between motor and metal plate. Bolts and screws are 'not " included in the package. Recommended bolts and screws are as follows. Motor name Hole for motor mounting Recommended bolts and screws PMSB-B42D E M3 (Depth 4.5mm) M3 4pcs PMSB-B56D E φ 4.5 Through hole (Thickness 5mm) M4 4pcs PMSB-B42D2ESD M3 (Depth 7mm) M3 4pcs PMSB-B56D1ESD M4 (Depth 8mm) M4 4pcs PMSB-B42D Series mounting PMSB-B56D Series mounting Bolt X 4 Hole for pilot Mounting plate Bolt X 4 PMSB-B42D2ESD mounting PMSB-B56D1ESD mounting Bolt X 4 Bolt X 4 Hole for pilot 8 Mounting plate

9 Mount the driver appropriate flat metal plate that can be expected good isolation from vibration and good heat dissipation. Fix securely with minimum 2 M3 screws and 2 spring washers horizontally or vertically. - PDSA-BX M3 bolts (or screw) X 2, Washers X 2 Driver mounting 1 Driver mounting 2 Bolt X 2 Mounting plate Bolt X 2 Mounting plate <Precaution> Keep enough free space more than 3cm for horizontal direction and 5cm for vertical direction for driver mounting. Attach the load onto the motor output shaft with the following procedure. When the load is attached to the motor shaft directly or applied through the mechanical coupling, align the center of the motor output shaft and the load center. When the load is applied through the belt or the gear, keep parallel between the motor output shaft and the load center. The motor and the driver generates temperature rise. Keep enough free space for good heat dissipation. Do not rotate the motor shaft more than 50 r/m(before gear reduction) by the external force. Keep the load within the following listed values. Otherwise, it may cause the shaft to bend or to break. Radial load value is measured at the top of the output shaft. Load direction Item name Thrust to the shaft Radial to the shaft PMSB-B42D E 3.5N (0.35kgf) 20N (2kgf) PMSB-B56D E 5.4N (0.54kgf) 50N (5kgf) PMSB-B42D2ESD 15N (1.5kgf) 10N (1kgf) PMSB-B56D1ESD 30N (3kgf) 30N (3kgf) 9

10 3-6. Cable & Connection with driver Connect 3 cables to the driver. Cables are hooked up by the connectors. Refer functions to the signal specifications of the cable connection <Precaution> Plug and unplug connectors must be done with power supply turned off. Plug the connector securely after confirming connector orientation. Improper connection may cause motor malfunction or the motor damage. Unplug connector pushing the lock part of the connector housing. Use the cable as short as possible and do not wind or bundle the remainders. Insulate the unused signal cables, or connect them to DC5V power or signal ground to prevent from contacting other devices. Use ferrite core, shield the cables by conductive tape or braided shield are recommended if the noise became a problem. CN3 CN1 CN2 Power supply cable connection Connect power supply cable to CN1. CN1 Signal specifications (CN 1 Mating connector : JST XAP-02-1) Pin Signal Specifications/ Description 1(RD) Vcc DC24V ± 10% 2(BK) GND Power GND Motor - Driver cable connection Connect motor - driver cable to CN3. CN3 Signal specifications (CN3 Mating connector : JST PAP-08VS) Pin Signal Specifications/ Description 1(WT) ENC_B Encoder B phase 2(GN) ENC_A Encoder A phase 3(BK) GND Encoder GND 4(BL) +5V Encoder power 5(YL) B Motor B phase 6(OR) A Motor A phase 7(RD) B Motor B phase 8(BR) A Motor A phase 10

11 Signal cable connection Connect signal cable to CN2. CN2 Signal specifications (CN2 Mating connector : JST GHDR-20V-S (F) ) Pin Signal Signal type 1(BR) NC - 2(BR/WT) NC - 3(RD/WT) NC - 4(RD) NC - 5(OR/WT) MST ー 6(OR) MST + Out 7(YL/WT) ALARM ー 8(YL) ALARM + Out 9(GN/WT) READY/ BUSY ー 10(GN) READY/ BUSY + Out AUTO_ 11(BL/WT) CURRENT ー In 12(BL) AUTO_ CURRENT + 13(VT/WT) MST_CLR ー 14(VT) MST_CLR + In 15(GR/ ENABLE ー WT) In 16(GR) ENABLE + 17(BK/WT) CCW ー (DIR ー ) 18(WT) CCW + (DIR +) In 19(PK/WT) CW ー (PLS ー ) 20(PK) CW + (PLS +) In Function N/A Stall alarm signal 1 System alarm signal Ready/Busy signal Automatic power down enable signal Stall alarm clear signal Motor enable signal CCW pulse signal (Direction signal) CW pulse signal (Pulse signal) Specifications/Description N/A Do not connect anything. Sealing signal cables properly not to contact each other. OFF: Openloop stall detection mode - Motor stall : Closedloop operation mode - Excessive deviation error or excessive load error ON : Normal operation OFF: System alarm ON: Normal operation OFF: Motor operation execute ON: Motor stop OFF: Motor holding current goes to SW1 No5pin set current 100[ms] after pulse signal input stopped. ON: Motor holding current is maintained at running current at SW2 OFF: Normal operation ON: Motor stall (Miss step) alarm clear OFF: Current disable ON: Current enable 2 pulse input mode - CCW pulse signal input 1 pulse input mode - Direction signal input OFF: CW direction/ ON: CCW direction 2 pulse input mode - CW pulse signal input 1 pulse input mode - Pulse signal input 1 To clear stall alarm signal, input signal to stall alarm clear. (See P21 for details.) 2 Alarm LED blinking cycle shows error description (See P23 for details). Bracket ( ) after pin number shows cable color. "OFF" in chart shows photocoupler off condition and "ON" in chart shows photocoupler on condition respectively. CW shows clockwise direction and CCW shows counterclockwise direction viewed from motor mounting surface. 11

12 3-7. Connection with peripherals. Driver & Power supply / External signal / Motor connection Connect the power supply and the controller referring the following examples. Connections must be done under the condition of the power supply turned off. < Driver & Power supply / External signal / Motor connection example> Bracket () after pin number shows cable color. R 1 and R 2 show external resistors for current limit. Improper connections may lead motor and other peripherals damages. 12

13 I/O signal diagram Input signal to the motor driver [ CW+(PLS+) / CW-(PLS ー ) / CCW+(DIR+) / CCW-(DIR ー ) / ENABLE+ / ENABLE ー / MST_ CLR+ / MST_CLR ー / AUTO_CURRENT+ / AUTO_CURRENT ー Signal ] Driver input is photocoupler input. Connect to external device referring the following connection example. < Input circuit example > 1) Connect directly without external resistor "R 1 " when applying DC+5V to V+, 2) Use external resistor "R 1 " to keep photocoupler current not to exceed 10mA when applying more than DC+5V to V+ The formula of the external resistor value is as follows. R 1 (External resistor value) >= ( (+v) Vce) / (Photocoupler current ) ohms Ex) When use DC+24[V] for V+, resistor value should be Approx. 2K ohms. Photocoupler current in the driver circuit should be 5 to 10mA Use +V in the range of 5 to 30V. Applying more than DC5V signal voltage without external resistor may cause driver damage. Output signal from the motor driver [ READY/BUSY+ / READY/BUSY ー / ALARM+ / ALARM ー / MST+ / MST ー Signal ] Driver output is photocoupler open-collector output. Connect to external device referring the following connection example. < Output circuit example > 1) Keep photocoupler current 10mA or lower confirming with the specifications of the controller. 2) Use external resistor "R2" to keep photocoupler current not to exceed 10mA, when expected current exceeds 10mA. The formula of the external resistor value is as follows. R 2 (External resistor value)>= ((+V)-VF-Vce) / ( Photocoupler current) Ohms VF shows voltage drop of the connected electrical component. Vce = 0.6V when photocoupler current is 1mA and Vce = 1.8V when photocoupler current is 10mA Use +V in the range of 5 to 30V. Withdrawing more than 10mA current without external resistor may cause driver damage. 13

14 3-8. Switch setting Before staring the operation, make the following set up with the switch on PDSA-BX driver board. These settings must be done with the power supply turned off. Switch ON Switch OFF SW1 SW2 Resolution setting (SW1 : Pin No. 1 & 2) Set the motor resolution (Pulse/Rotation) SW1 Pin No. Resolution Step Angle 1 2 (Pulse / Rotation) (Deg./Pulse) ON (Default) ON (Default) 400P/R 0.9 ON OFF 800P/R 0.45 OFF ON 1600P/R OFF OFF 3200P/R Setting higher resolution allows more precise step angle for each command pulse and reduce the motor running vibration. Use less than 100ms interval pulse command signal (More than 10pps) in 3,200 P/R setting. More than 100ms interval pulse command signal dose not work READY/BUSY output signal and automatic power down function correctly. Pulse input mode setting (SW1 : Pin No. 3) Set the pulse input mode. 13 SW1 Pin No.3 ON (Default) OFF Pulse input mode 2 pulse input mode (CW/CCW) 1 pulse input mode (PLS/DIR) Description 2 pulse input mode is to run the motor using CW (Clockwise) signal and CCW (Counterclockwise) signal respectively. With CW signal input, motor output shaft (viewed from the mounting surface side) rotates CW. With CCW signal input, the motor output shaft rotate CCW. 1 pulse input mode is to run the motor using PLS( Pulse) signal and DIR (Direction) signal. With PLS signal input the motor output shaft rotates and rotation direction is controlled by DIR signal. With DIR On, the motor output shaft rotates CW and with DIR Off, the motor output shaft rotates CCW direction.

15 Motor operation mode setting (SW1 : Pin No.4) Set the motor operation mode SW1 Pin No.4 ON (Default) OFF Motor operation mode Open-loop stall detection mode Closedloop operation mode Function Output alarm signal (MST) and stop motor operation without energized when motor stalls. Motor keeps operation and traces command pulse without stalling even when excessive acceleration order or impermanent excessive load applies. Description Motor runs in open-loop operation. Motor stall : When more than 3.6 Deg. deviation between rotor position and input pulse occurs, output stall alarm (MST) and motor stops without energized. Motor runs in closed-loop operation. Motor keeps operation and trace command pulse even when the deviation between rotor position and input pulse occurs by excessive acceleration or impermanent excessive load. Excessive deviation error : When the position deviation exceeds 1080 Deg, output stall alarm (MST) and motor stops without energized. Excessive load error : When more than 3.6 Deg deviation condition continues more than 5 seconds, output stall alarm and motor stops without energized. To clear stall alarm signal (MST), input signal to stall alarm clear (MST_CLR) is required (See P19 for details). Automatic power down current setting (SW1 : Pin No.5) Set the automatic power down current. The set parameter activates when Automatic power down signal input is "Off". SW1 Pin No.5 Setting ON (Default) Running current setting X 50% OFF Running current setting X 25% Set the automatic power down current separately from running current setting and effective for temperature rise prevention during motor holding condition. When automatic power down signal input (AUTO_CURRENT) is "On", the motor holding current is maintained at running current at SW2. Holding torque is getting lower in accordance with lower current setting. 15

16 Velocity filter setting (SW1: Pin 6, 7 & 8) Set velocity filter response time constant SW1 Pin No ON ON ON (Default) (Default) (Default) Setting 0ms (Filter inactive) ON ON OFF 2ms ON OFF ON 5ms ON OFF OFF 10ms OFF ON ON 20ms OFF ON OFF 50ms OFF OFF ON 70ms OFF OFF OFF 100ms Velocity filter setting makes smooth acceleration/deceleration and reduce vibration. < Velocity filter setting image > 0ms (Filter inactive) setting 50ms (Filter active) setting Input pulse velocity Motor rotation velocity Ready/Busy output signal timing Excessive time constant setting spoils the motor synchronization to the input pulse signal and delays the motor response time. Set parameter appropriately in accordance to actual application and the load condition. Improper velocity filter setting may cause motor stalling at 400P/R resolution setting in open-loop stall detection mode. It recommends to go higher resolution setting, shorten acceleration/deceleration time or change the load condition to avoid motor stalling. 16

17 Running current setting (SW2) Set motor running current and adjust motor rotating torque. Current [A] Rotary SW setting ( ± 20%) 0 (Default) 0.6A 1 0.8A 2 1.0A 3 1.2A 4 1.4A 5 1.6A 6 1.8A 7 2.0A 8 2.2A 9 2.4A A 2.6A B 2.8A C 3.0A D 3.0A E 3.0A F 3.0A Set motor running current as follows, if specific setting is not required. Item name Rotary SW setting Current [A] ( ± 20%) PMSB-B42D E 5 1.6A PMSB-B56D E B 2.8A PMSB-B42D2ESD 3 1.2A PMSB-B56D1ESD 9 2.4A Motor running torque goes lower if the running current setting is lower. Contrarily, the motor running torque goes higher if the running current setting is higher. If the running current setting is too high, the motor generates excessive temperature rise and result in motor burning. Keep the motor surface temperature at 70Deg. C( 158Deg.F) or lower. 17

18 4. Operation 4-1. Timing chart Motor operation and timing chart Operate the motor referring the following timing chart. 1 CW shows clockwise direction and CCW shows counterclockwise direction viewed from motor mounting surface. 2 "OFF" in chart shows photocoupler off condition and "On" in chart shows photocoupler on condition respectively. 3 Wait 5 seconds and more after power supply turned off when power supply resetting. 4 Initializing operation time varies in load condition. It takes approximately 1 second from motor enable signal input to Ready signal "On". 5 Acceleration / Deceleration time varies in operation mode, velocity filter setting and load condition. 6 Time to READY/BUSY signal varies in operation mode, velocity filter setting and load condition. 18

19 7 Wait time for direction change varies in operation mode, velocity filter setting and load condition. To secure appropriate wait time, it recommend to monitor READY/ BUSY signal. 8 When motor current enable is turned off, motor current shuts down, motor is not energized and position deviation check stops. When motor current enable is turned on, motor starts initializing operation and starts position deviation check. Do not start/stop motor operation with power supply switching and must use pulse signals for operation start/stop. Improper operation may cause injuries or property damage. 19

20 Pulse wave (CW/CCW) Input pulse signal referring the following chart. 1 CW shows clockwise direction and CCW shows counterclockwise direction viewed from motor mounting surface. 2 "OFF" in chart shows photocoupler off condition and "On" in chart shows photocoupler on condition respectively. Keep photocoupler off condition when pulse is stopped. Do not input CW pulse and CCW pulse in the same timing at 2 pulse input mode. Motor does not rotate correctly. 20

21 Stall alarm and stall alarm clear (MST/MST_CLR) Motor stops without energized with stall alarm (MST) output when motor stalls in open-loop stall detection mode, excessive deviation or excessive load in closed-loop operation mode. To restart motor operation, input signal on stall alarm clear (MST_ CLR) after removing the cause of stalling, excessive deviation or excessive load. 1 CW shows clockwise direction and CCW shows counterclockwise direction viewed from motor mounting surface. 2 "OFF" in chart shows photocoupler off condition and "On" in chart shows photocoupler on condition respectively. 3 Initializing operation time varies in load condition. It takes approximately 1 second from motor enable signal input to Ready signal "On". 4 Pulse signals are ignored when stall alarm (MST) outputs. When stall alarm (MST) outputs, motor stops without energized and no holding torque performs. System alarm cannot be cleared by stall alarm clear (MST_CLR) input. To clear stall alarm, input signal on stall alarm clear (MST_CLR) after removing the cause of stall, excessive deviation or excessive load. Start without removing the cause of problem may cause injuries or property damage. 21

22 4-2. LED Driver equips 2 LED indicators show driver and motor status by lighting and blinking. Make sure LED blinking cycles and error description when LED blinks and remove the cause of error. LED Name Color Type Light/Blink condition Power LED (Power supply indicator) Alarm LED (Alarm indicator) Green Orange Light Light Blink LED turns on when power supply is ON. LED turns on when position deviation occurs in closed-loop operation mode. LED blinks when error occurs or protective function works with stall alarm or system alarm signal output. It is possible to identify error description by blinking cycle time. See protective function and alarm column for more details Protective functions / Alarms Driver has alarm function to inform motor stalling including excessive deviation and excessive load and protective functions for system error. It is possible to identify the cause of alarm and system error by counting blinking cycles. Refer to the following page for recovering and countermeasure of problems. LED blinks in particular error cycle of 400ms light on and 400ms light off with 1.2 second interval N ms 400 ms 1.2 s 3 N 22

23 Alarm LED Blinking cycle and Error description Blinking cycle Output Error type Cause Reinstatement Stall alarm Stall alarm System alarm System alarm System alarm System alarm Stall detection Excessive deviation Excessive load Over heat Excessive regenerative voltage Motor stalling in open-loop stall detection mode Excessive position deviation in closed-loop operation mode Excessive load in closed loop operation mode Temperature of the thermistor on driver board reaches 80Deg. C Internal voltage goes more than 32VDC by regenerative voltage. Low voltage Input voltage goes less than 18VDC Excessive velocity Input pulse exceeds 80Khz or motor rotation velocity reaches 3,500 r/min Stall alarm clear (MST_ CLR) Stall alarm clear (MST_ CLR) Stall alarm clear (MST_ CLR) Power restarting Power restarting Power restarting Power restarting System alarm System error Problem of driver IC Power restarting System alarm Initialization error Motor initialization error Power restarting When stall alarm (MST) or system alarm outputs, motor stops without energized and no holding torque performs. Before re-start operation, remove the cause of stall alarm and system alarm. Start without removing the cause of problem may cause injuries or property damage. 23

24 5. General specifications < Standard model > 24 Item name Motor name Driver name CSA- BX42D2E PMSB- B42D2E CSA- BX42D4E PMSB- B42D4E CSA- BX56D1E PMSB- B56D1E PDSA-BX CSA- BX56D3E PMSB- B56D3E Flange size 42mm 56.4mm Resolution Driving method Power supply voltage CSA- BX56D5E PMSB- B56D5E 400P/R (0.9Deg.), 800P/R (0.45Deg.), 1,600P/R (0.225Deg.) Bracket() shows step angle at each resolution setting. 2 phase bipolar chopper drive DC24V±10% Current 1.6A/phase 2.8A/phase Maximum holding torque Rotor inertia Permissible inertia 0.23 N m 0.38 N m 0.44 N m 0.77 N m 1.40 N m (400P/R 0 pps) Approx. 40 g cm 2 Approx. 400 g cm 2 Approx. 70 g cm 2 Approx. 700 g cm 2 Approx. 153 g cm 2 Approx g cm 2 (400P/R 0 pps) Approx. 290 g cm 2 Approx g cm 2 Permissible thrust load 3.5 N (0.35 kgf) 5.4 N(0.54 kgf) Permissible radial load Motor mass Driver mass Insulation resistance Die-electrical strength Operating ambient temperature Operating ambient humidity Storage temperature Storage humidity Atmosphere Environmental 20 N (2kgf) at the top of output shaft Approx. 0.29kg Approx. 0.42kg Approx. 513 g cm 2 Approx g cm 2 50 N (5kgf) at the top of output shaft Approx. 0.51kg Approx. 0.08kg Approx. 0.71kg 500 VD.C Merger 100M ohms or more A.C.500V 50/60Hz 1 minute. 0 to 40 Deg.C No freezing. 85% or less. No condensing Driver : -10 to + 50 Deg.C. No freezing Motor : -20 to + 60 Deg.C. No freezing 85% or less. No condensing No corrosive gas, no dust surroundings, No water and oil splash. RoHS (2002/95/EC) Approx. 1.10kg

25 < Geared model > Item name CSA-BX42D2ESD CSA-BX56D1ESD Motor name PMSB-B42D2ESD PMSB-B56D1ESD Driver name PDSA-BX Flange size 42mm 60mm Resolution Driving method 4000 P/R(0.09Deg.), 8000 P/R(0.045Deg.), 16,000 P/R(0.0225Deg.), 32,000 P/R( Deg.) Bracket() shows step angle at each resolution setting. 2 phase bipolar chopper drive Power supply voltage DC24V ± 10% Current 1.2 A/ Phaze 2.4 A/ Phaze Permissible torque 1.0 N m 3.0 N m Permissible rotation speed Backlash r/min Approx.1 2 Deg. Rotor inertia Approx.40 g cm 2 Approx.135 g cm 2 Permissible inertia Approx.40,000 g cm 2 Approx.135,000 g cm 2 Permissible thrust load 15 N (1.5 kgf) 30 N (3 kgf) Permissible radial load 10 N (1kgf) at the top of output shaft 30 N (3kgf) at the top of output shaft Motor mass Approx. 0.38kg Approx. 0.81kg Driver mass Insulation resistance Die-electrical strength Operating ambient temperature Operating ambient humidity Storage temperature Storage humidity Atmosphere Environmental Approx. 0.08kg 500 VD.C Merger 100M ohms or more A.C.500V 50/60Hz 1 minute. 0 to 40 Deg.C No freezing. 85% or less. No condensing Driver : -10 to + 50 Deg.C. No freezing Motor : -20 to + 60 Deg.C. No freezing 85% or less. No condensing No corrosive gas, no dust surroundings, No water and oil splash. RoHS (2002/95/EC) 25

26 6. Troubleshooting & countermeasure When the motor cannot be operated correctly. Refer to the following troubleshooting and countermeasure list. If the incorrect operation persists, contact your sale agent or sales office. When Alarm LED does not blink Phenomenon Possible cause Countermeasure Motor is not energized. (Output shaft can be rotated by fingers like "power off" condition) Motor does not rotate Motor rotates in reverse direction. Cable miss connection or improper cable connection Power supply "Off" Motor current enable signal is "Off" (Pulse) signal cable miss connection, improper cable connection or disconnection. Motor running current is not set properly No pulse signal input. Improper switch (SW1)setting Reverse connection of CW input signal and CCW input signal at 2 pulse input mode. Input of the rotation direction signal is not correct at 1 pulse input mode. Incorrect switch (SW1) setting. Correct the connection of the cable with the power supply and the motor cable with driver Check if the power supply is "On" Set the motor current enable signal is "On" Check if the correct connection of the signal cable to the driver. Also check if the signal cable has not been damaged. Set the motor running current properly. Check if proper pulse signal from the controller applied. Correct the pulse input mode setting. Incorrect input mode setting may the cause no rotation of the motor. Connect CW pulse signal to CW signal input and CCW pulse signal to CCW signal input. Correct input signal logic of the rotation direction (Photocoupler on - CW direction and photocoupler off - CCW direction). Correct the pulse input mode setting. 26

27 Phenomenon Possible cause Countermeasure Unstable motor operation Motor generates excessive heat Motor does not generate expected torque. Motor rotation does not reach expected value Motor holding current does not go down. Motor generates excessive vibration (noise) Signal cable or motor cable miss connection or improper cable connection. Incorrect signal voltage input or incorrect frequency. Motor operation time is too long Motor holding current setting is too high Incorrect power supply voltage or power supply current capacity is not enough. Incorrect running current setting or incorrect holding current setting Correct the connection of the signal cable between driver and controller. Also check the correct connection of the motor cable between driver and motor. Also check if the cable has not been damaged. Check the signal voltage and frequency. Shorten the operating time or extend nonoperation interval. Also use external cooling fan for the motor to cool. Adjust the motor holding current at lower value. Check the power supply voltage. Prepare the power supply that has enough current capacity. Adjust the motor running current setting (SW2). Incorrect resolution setting Correct the resolution setting (SW1) Input pulse is too much or Check the supplied pulse from controller. less. Input pulse does not match Input enough pulse in accordance with required pulse after gear reduction. gear ratio. Automatic power down disabled. Set automatic power down enable. Incorrect motor holding current setting Correct holding current setting. Motor resonates Change the operation velocity or use the mounting rubber damper. Changing the resolution setting is also effective to minimize the motor resonance. Use velocity filter to reduce acceleration/ deceleration vibration. Load is small If output torque is too much against load, increase load or reduce the current setting. Use velocity filter to reduce acceleration/ deceleration vibration. 27

28 When Alarm LED blinks ALARM LED Blinking cycle Possible cause Motor stalling in open-loop stall detection mode. Excessive load, Excessive acceleration / Deceleration or vibration. Position deviation or load exceeds the motor tracing range in closed-loop operation mode. Excessive load or command pulse input is too fast beyond the motor performance. Overheat protection works. Temperature of the thermistor on driver board is too high. Excessive regenerative voltage protection works. Low voltage protection works Improper power supply voltage setting. Less capable power supply capacity. Wrong connection. Excessive velocity protection works. Command pulse input is too fast or motor velocity is too high. Driver operation problem. External noise, malfunction by external reason or breakdown. Initialization failure. Excessive load. Motor cable miss connection. Countermeasure Reduce the load if the cause is excessive load. Operate in trapezoidal acceleration / deceleration curve in accordance with the motor performance. Use velocity filter to reduce acceleration/deceleration vibration. Reduce the load if the cause is excessive load. Operate in accordance with the motor performance. Keep enough surrounding space for good heat dissipation. Mount the driver appropriate flat metal plate that can be expected good heat dissipation. Reduce the load if the cause is excessive load. Review and change trapezoidal acceleration / deceleration curve in accordance with motor performance. Check the power supply voltage setting, power supply capacity and connection. Keep maximum command pulse input less than 80Kpps and maximum motor velocity less than 3,500 rpm. Remove the source of noise. Re-start power supply. Reduce the load if the cause is excessive load. Correct the connection of the motor cable with driver. 28

29 7. Periodical inspection For the safety operation, it is recommended that periodical inspection be done after each motor operation. Stop operation immediately and turn off the motor power supply, if unexpected system malfunction occurs. Then, contact sales agent or sales office. Recommended inspection items - No unusual noise from the motor bearing and moving components. - No foul smell from the motor unit. - No misalignment between the center of the motor output shaft and the load center. - No looseness of the motor and the driver mounting screw. - No looseness of the cable connection and no unusual connection. - No damage and no excessive stress on the cable. 8. Warranty Within one (1) year from the date of invoice ("Warranty Period"), product breakage, deformation, or defect ("Defects") by cause of Shinano Kenshi, the product you purchased shall be repaired, or be replaced at no charge. This warranty excludes and dose not cover any defects arising from or related to the followings. (1) Use excluding Suggested applications (2) Abuse and misuse. (3) Acts of God (Earthquake, lightning, fire or flood) (4) Negligence in observing specifications, applications, precaution of using, use conditions, drawings, other matters that related to the product, product (including optional parts) operation manuals or against other indications regarding safe use. (5) Unauthorized machining, repairs, modifications or disassembly. (6) Use with another manufacture's devices. (7) Exceeding product life. (8) Other than above, defects cannot be attributed to Shinano Kenshi. After warranty period or out of the warranty, any and all repairs, replacements and consumable replacements will be charged appropriately. Shinano Kenshi is not liable for direct damages, loss of opportunities, special damages, incidental damages and other consequent damages or loss caused by production line stop of factory and factory facilities with using our products. 29

30 9. Notes Reprinting or copying this operation manual is prohibited. Product name, specifications, dimensions may change without notice for product improvement. Products shown in this manual may be discontinued without prior notice. Contact sales agents or sales offices if modification or machining is required. 30

31 < memo > 31

32 Designed and manufactured by Shinano Kenshi Co.,Ltd Kami-maruko, Ueda-shi, Nagano-ken, JAPAN TEL(81) FAX(81) Plexmotion support center Plexmotion@skcj.co.jp 2011 Shinano Kenshi Co.,Ltd. is a trademark of Shinano Kenshi Co.,Ltd.

Names and Functions of Driver Parts

Names and Functions of Driver Parts List of Motor Connection and Extended Accessories Installation Product Line Dimensions and Operation Functions Connection and Operation Names and Functions of Parts 5 Power Supply Input/ Regeneration Unit

More information

Instruction Manual. Selectable Microstep 5-ph Stepping Motor Driver RD-053MS RORZE CORPORATION

Instruction Manual. Selectable Microstep 5-ph Stepping Motor Driver RD-053MS RORZE CORPORATION Instruction Manual Selectable Microstep 5ph Stepping Motor Driver RD053MS RORZE CORPORATION Be sure to read the following precautions for your safety. This section describes safety precautions to avoid

More information

OPERATING MANUAL. Table of Contents. 5 Phase Stepping Motor and Driver. PN Geared Type HP Precautions...Page 2

OPERATING MANUAL. Table of Contents. 5 Phase Stepping Motor and Driver. PN Geared Type HP Precautions...Page 2 HP-4117-3 5 Phase Stepping and UPK W Series PN Geared Type OPERATING MANUAL C Table of Contents 1. Precautions...Page 2 2. Product Verification...Page 3 3. Names and Function of Parts... Page 4 4. Installation...Page

More information

STR3. Step Motor Drive. User Manual

STR3. Step Motor Drive. User Manual STR3 Step Motor Drive User Manual Contents 1 Introduction... 3 1.1 Overview... 3 1.2 Features... 3 1.3 Block Diagram... 4 1.4 Safety Instructions... 5 2 Getting Started... 6 2.1 Mounting Hardware... 6

More information

Instruction Manual. Selectable Microstep 2-ph Stepping Motor Driver RD-026MSA RORZE CORPORATION

Instruction Manual. Selectable Microstep 2-ph Stepping Motor Driver RD-026MSA RORZE CORPORATION Instruction Manual Selectable Microstep 2ph Stepping Motor Driver RD026MSA RORZE CORPORATION Be sure to read the following precautions for your safety. This section describes safety precautions to avoid

More information

NIDEC COPAL ELECTRONICS CORP.

NIDEC COPAL ELECTRONICS CORP. 1 / 8 Specifications Model No. TF037F-2000-F Issuing Date Aug.1, 2017 1.Scope This document applies to Blower TF037F-2000-F (hereinafter referred to as "PRODUCT"), a product of NIDEC COPAL ELECTRONICS

More information

Brake Pack SB50W. Standard AC Motors A-143. Standard AC Motors Intro duction. Brake Pack. AC Speed Control Motors Inverter.

Brake Pack SB50W. Standard AC Motors A-143. Standard AC Motors Intro duction. Brake Pack. AC Speed Control Motors Inverter. Standard AC SB5W Standard AC Intro duction Induction Reversible Right -Angle Gearheads SB5W AC Speed Control Inverter SB5W US ES2 FE1/FE2 Watertight, Dust-Resistant Torque Accessories Installation A-143

More information

Cat. No. I526-E1-1 USER S MANUAL 3G3IV-PLKEB2 /4. Braking Resistor Units 3G3IV-PCDBR2 B/4 B. Braking Units

Cat. No. I526-E1-1 USER S MANUAL 3G3IV-PLKEB2 /4. Braking Resistor Units 3G3IV-PCDBR2 B/4 B. Braking Units Cat. No. I526-E1-1 USER S MANUAL 3G3IV-PLKEB2 /4 Braking Resistor Units 3G3IV-PCDBR2 B/4 B Braking Units Thank you for choosing an OMRON Braking Resistor Unit and Braking Unit. Proper use and handling

More information

DRV-1. Step Motor Drive. User Manual Mentor Avenue Cincinnati, Ohio Tel (513)

DRV-1. Step Motor Drive. User Manual Mentor Avenue Cincinnati, Ohio Tel (513) DRV-1 Step Motor Drive User Manual 1776 Mentor Avenue Cincinnati, Ohio 45212 Tel (513) 318-4600 www.resolutionair.com 2 Contents 1 Introduction... 3 1.1 Overview... 3 1.2 Features... 3 1.3 Block Diagram...

More information

Completely free from the Concern of Loss of Position (Alarm Feneration when Step-Out) Perfect Positiooning and Completion (Positioning Completion

Completely free from the Concern of Loss of Position (Alarm Feneration when Step-Out) Perfect Positiooning and Completion (Positioning Completion Completely free from the Concern of Loss of Position (Alarm Feneration when Step-Out) Perfect Positiooning and Completion (Positioning Completion Signal Generation) Don t Care what the Phase of Motor is

More information

SR3-mini. Step Motor Drive User Manual. AMP & MOONS Automation

SR3-mini. Step Motor Drive User Manual. AMP & MOONS Automation SR3-mini Step Motor Drive User Manual AMP & MOONS Automation Contents 1 Introduction... 3 1.1 Overview...3 1.2 Features...3 1.3 Block Diagram...4 1.4 Safety Instructions...5 2 Getting Started... 6 2.1

More information

5-Phase Stepper Motor

5-Phase Stepper Motor Ordering Information Application model: Standard shaft type, Hollow shaft type, Shaft type+ A 8K M 5 6 6 B Motor type Motor phase Rated current Max. Holding torque Shaft type Motor length : provides single

More information

AC Motor Systems. Speed Control Systems B-137. Speed Control Systems Introduction. BHF Series FE200 ES01/ US Series

AC Motor Systems. Speed Control Systems B-137. Speed Control Systems Introduction. BHF Series FE200 ES01/ US Series AC Motor Systems Speed Control Systems Introduction BHF Series FE1/FE2 ES1/ES2 US Series FB FE1/ FE2 ES1/ ES2 US Installation Page BHF Series B-138 FE1/FE2 B-156 ES1/ES2 B-172 US Series B-22 B-137 RoHS-Compliant

More information

ASC Series OPERATING MANUAL. Table of Contents 1 Introduction Safety precautions Precautions for use Preparation...

ASC Series OPERATING MANUAL. Table of Contents 1 Introduction Safety precautions Precautions for use Preparation... HM-6163-12 ASC Series OPERATING MANUAL Thank you for purchasing an Oriental Motor product. This Operating Manual describes product handling procedures and safety precautions. Please read it thoroughly

More information

OPERATING MANUAL. High-efficiency AR Series. Stepping motor and driver package. Introduction. Applicable motor. Before use

OPERATING MANUAL. High-efficiency AR Series. Stepping motor and driver package. Introduction. Applicable motor. Before use HM-08 OPERATING MANUAL Stepping motor and driver package High-efficiency AR Series DC power input Built-in Controller Type (RS-8 communication function) Driver Introduction Before use Only qualified personnel

More information

Instruction Manual. Selectable Microstep 2-ph Stepping Motor Driver RD-021M8 RORZE CORPORATION

Instruction Manual. Selectable Microstep 2-ph Stepping Motor Driver RD-021M8 RORZE CORPORATION Instruction Manual Selectable Microstep 2-ph Stepping Motor Driver RD-021M8 RORZE CORPORTION e sure to read the following precautions for your safety. This section describes safety precautions to avoid

More information

Instruction Manual. Selectable Microstep 2-ph Stepping Motor Driver RD-023MS RORZE CORPORATION

Instruction Manual. Selectable Microstep 2-ph Stepping Motor Driver RD-023MS RORZE CORPORATION Instruction Manual Selectable Microstep 2ph Stepping Motor Driver RD23MS RORZE CORPORATION Be sure to read the following precautions for your safety. This section describes safety precautions to avoid

More information

Instruction Manual. 2-ph Stepping Motor Driver RD-123 RD-123H,RD-126 RORZE CORPORATION

Instruction Manual. 2-ph Stepping Motor Driver RD-123 RD-123H,RD-126 RORZE CORPORATION Instruction Manual 2-ph Stepping Motor Driver RD-123 RD-123H,RD-126 RORZE CORPORTION e sure to read the following precautions for your safety. This section describes safety precautions to avoid danger

More information

KL-8070D. Fully Digital Stepping Driver. Table of Contents 1. Introduction, Features and Applications...1 Introduction...1 Features...

KL-8070D. Fully Digital Stepping Driver. Table of Contents 1. Introduction, Features and Applications...1 Introduction...1 Features... Contents KL-8070D Fully Digital Stepping Driver Attention: Please read this manual carefully before using the driver! I Table of Contents 1. Introduction, Features and Applications...1 Introduction......1

More information

User s Manual. For DM860T. Fully Digital Stepper Drive. Version 1.0 Designed by StepperOnline All Rights Reserved

User s Manual. For DM860T. Fully Digital Stepper Drive. Version 1.0 Designed by StepperOnline All Rights Reserved User s Manual For DM860T Fully Digital Stepper Drive Version 1.0 Designed by StepperOnline 2017 All Rights Reserved Web site: www.omc-stepperonline.com E-Mail: sales@stepperonline.com Table of Contents

More information

St epping Mot or s C-i ORIENTAL MOTOR GENERAL CATALOG 2009/2010

St epping Mot or s C-i ORIENTAL MOTOR GENERAL CATALOG 2009/2010 C-i ORIENTAL MOTOR GENERAL CATALOG 29/21 C Introduction C-2 Stepping Motor and Driver Packages AC Input Stepping Motor and Driver Packages DC Input Stepping Motors AC Input AS Series C-14 DC Input ASC

More information

Brushless DC Motor Unit. Brushless DC Motor (24 V DC Input) 50 W Model 24DCM W Model 24DCM-372 MDS-01AL

Brushless DC Motor Unit. Brushless DC Motor (24 V DC Input) 50 W Model 24DCM W Model 24DCM-372 MDS-01AL Brushless DC Motor Unit Brushless DC Motor (24 V DC Input) 50 W Model 24DCM-371 100 W Model 24DCM-372 Driver MDS-01AL002-01 User s Guide Thank you for purchasing the Minebea 24DCM brushless DC motor unit.

More information

User Manual of 2MA2282

User Manual of 2MA2282 ECG-SAVEBASE EMAIL:EBAY@SAVEBASE.COM WEB: HTTP://STORES.EBAY.CO.UK/SAVEBASE User Manual of 2MA2282 High Performance Microstepping Driver ECG-SAVEBASE ECG Safety Statement Easy Commercial Global is not

More information

NIDEC COPAL ELECTRONICS CORP.

NIDEC COPAL ELECTRONICS CORP. NIDEC COPA EECTRONICS CORP. 1 / 5 Specifications Model No. TF037C-2100-F Issuing Date Aug.1, 2017 1. Scope This specification applies to Blower TF037C-2100-F (hereinafter referred to as "the PRODUCT"),

More information

AZ Series Motor OPERATING MANUAL. Introduction. Safety precautions. CE Marking

AZ Series Motor OPERATING MANUAL. Introduction. Safety precautions. CE Marking HM-6244-3 OPERATING MANUAL Closed Loop Stepping and Driver Package AZ Series Introduction Before use Only qualified personnel should work with the product. Use the product correctly after thoroughly reading

More information

MondoStep 7.8. High Performance Microstepping Driver. User s Manual. Version PROBOTIX All Rights Reserved

MondoStep 7.8. High Performance Microstepping Driver. User s Manual. Version PROBOTIX All Rights Reserved MondoStep 7.8 High Performance Microstepping Driver User s Manual Version 1.0 2010 PROBOTIX All Rights Reserved Attention: Please read this manual carefully before using the driver! Table of Contents 1.

More information

Operating Manual For Stepper Driver

Operating Manual For Stepper Driver Contents Table of Contents Operating Manual For Stepper Driver 5042 High Performance Micro stepping Driver Attention: Please read this manual carefully before using the driver! E L E C T R O N I C S 54

More information

Brushless Motors. BMU Series. Connector Type NEW. Easy speed control, easier to use. New connector type with smart wiring.

Brushless Motors. BMU Series. Connector Type NEW. Easy speed control, easier to use. New connector type with smart wiring. Brushless Motors BMU Series NEW Connector Type Easy speed control, easier to use. New connector type with smart wiring. The new connector type in the compact, high-efficiency BMU series, directly connects

More information

NIDEC COPAL ELECTRONICS CORP. 1 / 7. Model No. Issuing Date

NIDEC COPAL ELECTRONICS CORP. 1 / 7. Model No. Issuing Date NIDEC COPAL ELECTRONICS CORP. / 7 Specifications Model No. Issuing Date TF037C-200-P Aug., 207. Scope This specification applies to Blower Kit:TF037C-200-P (hereinafter referred to as "the PRODUCT"), a

More information

User s Manual. For DM542T. Full Digital Stepper Drive

User s Manual. For DM542T. Full Digital Stepper Drive User s Manual For DM542T Full Digital Stepper Drive Designed by StepperOnline Manufactured by Leadshine 2017 All Rights ReservedAttention: Please read this manual carefully before using the drive! #7 Zhongke

More information

CBM-105FN/FP Circuit Board

CBM-105FN/FP Circuit Board CBM-105FN/FP Circuit Board Features Adjustable acceleration and deceleration time (0 to 2.5s) Stable speed operation Manual or automatic recovery of the thermal overload device One (1) rotary switch to

More information

Stepper Motors ver ver.5

Stepper Motors ver ver.5 A Stepper s Stepper s A-1 Overview... A-2 Overview and... A-15 & Stepper and RK Series A-16 RK... A-47... A-51 Stepper Series A-52 Stepper Series A-8 See Full Product Details Online www.orientalmotor.com

More information

TOWA SEIDEN INDUSTRIAL CO., LTD.

TOWA SEIDEN INDUSTRIAL CO., LTD. INSTRUCTION MANUAL SOUNDING LEVEL METER MODEL: TLX-120AP/200AP Meanings of indications for safety used in this Instruction Manual are as follows. WARNING: Indicates that improper handling assumes the risk

More information

FE100/FE200. AC Speed Control Motors. Features

FE100/FE200. AC Speed Control Motors. Features AC Speed Control Motors FE1/FE2 Additional Information Technical reference Page G-1 Safety standards Page H-2 The FE1/FE2 is a speed controller using inverter technology that enables speed control to be

More information

2: A, B 3: A, B, Z 4: A, A _, B, B _ 6: A, A _, B, B _, Z, Z _

2: A, B 3: A, B, Z 4: A, A _, B, B _ 6: A, A _, B, B _, Z, Z _ Diameter mm Shaft Type/Hollow Type/Built-In Type Incremental Rotary Encoder Features Diameter mm flange type Suitable for measuring angle, position, revolution, speed, acceleration and distance Power supply:

More information

DC power supply connect to VF-AS1/PS1 Optional initial charger MCR-2550 Instruction manual

DC power supply connect to VF-AS1/PS1 Optional initial charger MCR-2550 Instruction manual DC power supply connect to VF-AS1/PS1 Optional initial charger Instruction manual NOTE 1. Make sure that this instruction manual is delivered to the end user of the optional initial charger. 2. Read this

More information

2-PHASE STEPPING SYSTEMS. Ver.4

2-PHASE STEPPING SYSTEMS. Ver.4 -PHASE STEPPING SYSTEMS Ver. DC input set model DC input driver Stepping Motor Motor size: mm sq. (.inch sq.) to mm sq. (.inch sq.), mm (.inch) Stepping motors with integrated drivers Stepping motor for

More information

NX Series. Tuning-Free AC Servo Motor Unit

NX Series. Tuning-Free AC Servo Motor Unit Tuning-Free AC Servo Motor Unit NX Series An AC servo motor unit that is capable of high accuracy control with easy operation. Smooth operation can be achieved in high inertia loads or belt drive applications

More information

Filterpack FR-BFP2-(H)0.4K to (H)15K

Filterpack FR-BFP2-(H)0.4K to (H)15K INVERTER INSTRUCTION MANUAL FR-BFP2-(H)0.4K to (H)15K 1. Product Checking... 1 2. Applicable Inverter... 1 3. Installation... 2 3.1 Inverter Installation (installation of the )...2 4. Wiring... 4 5. Main

More information

DRL Series DFC driver Photocoupler inputs

DRL Series DFC driver Photocoupler inputs HP-1420-5 Compact actuator DRL Series DFC driver Photocoupler inputs OPERATING MANUAL Table of Contents Thank you for purchasing an Oriental Motor product. This operating manual describes product handling

More information

BLE2 Series D-42. Brushless Motor and Driver Package. Features Overview of BLE2 Series. Quick & Reliable Wiring/Connecting

BLE2 Series D-42. Brushless Motor and Driver Package. Features Overview of BLE2 Series. Quick & Reliable Wiring/Connecting D-42 Brushless Motor and Driver Package BLE2 Series Technical reference Page H-1 Regulations & Standards Page I-2 $For $ detailed information about regulations and standards, please

More information

CVK Series. 1.8, 0.72 and 0.36 Stepper Motor and Driver Package. DC Input

CVK Series. 1.8, 0.72 and 0.36 Stepper Motor and Driver Package. DC Input .8,.7 and.36 Stepper Motor and Driver Package CVK Series DC Input Compact, standardized drivers, combined with performance driven high torque stepper motors, for the optimum results. mm, 8 mm, 35 mm, mm,

More information

VF-S11 RS485 built-in board option RS4003Z Instruction Manual

VF-S11 RS485 built-in board option RS4003Z Instruction Manual VF-S11 RS485 built-in board option RS4003Z Instruction Manual NOTICE 1. Make sure that this instruction manual is delivered to the end user of RS485 built-in option board. 2. Read this manual before installing

More information

SR8-Plus 2 Phase Step Motor Drive

SR8-Plus 2 Phase Step Motor Drive 2 Phase Step Motor Drive User Manual Rev. 1.1 AMP & MOONS Automation Contents 1 Introduction... 3 1.1 Overview...3 1.2 Features...3 1.3 Block diagram...4 2 Mounting the Drive... 4 3 Connections... 5 3.1

More information

DP-304/DP-304-L Stepper Drive

DP-304/DP-304-L Stepper Drive DP-304/DP-304-L Stepper Drive User Manual WUXI XINJE ELECTRIC CO., LTD. NO. DC06 20111128 1.0 Catalog 1. Summary... 1 1-1. Characteristic... 1 1-2. Application... 1 1-3. Electric characters... 1 2. Operation

More information

DC Input. Brushless Motors/AC Speed Control Motors D-89. Brushless Motors/AC Speed Control Motors D-89. BLH Series. Overview, Product Series

DC Input. Brushless Motors/AC Speed Control Motors D-89. Brushless Motors/AC Speed Control Motors D-89. BLH Series. Overview, Product Series Brushless /C Speed Control D-89 Overview, Series Brushless /C Speed Control Brushless Brushless BMU BLE2 BX BLH Series BLH C Speed Control DSC US2 ccessories Installation D-89 D-9 Brushless BLH Series

More information

Instruction Manual. 2-ph Stepping Motor Driver RD-122 RORZE CORPORATION

Instruction Manual. 2-ph Stepping Motor Driver RD-122 RORZE CORPORATION Instruction Manual 2-ph Stepping Motor Driver RD-122 RORZE CORPORTION e sure to read the following precautions for your safety. This section describes safety precautions to avoid danger to you or someone

More information

User Manual. T6 Tachometer. Online: Telephone: P.O. Box St. Petersburg, Florida 33736

User Manual. T6 Tachometer. Online:   Telephone: P.O. Box St. Petersburg, Florida 33736 User Manual T6 Tachometer Online: www.phareselectronics.com Telephone: 727-623-0894 P.O. Box 67251 St. Petersburg, Florida 33736 Table of Contents Overview... 1 Description... 1 Wiring... 1 T6 Tachometer

More information

BLH. 24 VDC Input 15W / 30W / 50W / 100W BLH

BLH. 24 VDC Input 15W / 30W / 50W / 100W BLH BLH 24 VDC Input 15W / 30W / 50W / 100W BLH BLH BLH BLH BLH 2 3 System Configuration Geared Type/Combination Type Parallel Shaft Gearhead/Round Shaft Type The system configuration shown above is an example.

More information

Servo Motors B-1. Introduction B-2. NX Series B-9. Accessories B-47

Servo Motors B-1. Introduction B-2. NX Series B-9. Accessories B-47 B Servo Motors Servo Motors Introduction B-2 NX Series B-9 Accessories B-47 Introduction NX Accessories This catalog contains information necessary for informed product selection. Additional product details

More information

Technical Explanation for Inverters

Technical Explanation for Inverters CSM_Inverter_TG_E_1_2 Introduction What Is an Inverter? An inverter controls the frequency of power supplied to an AC motor to control the rotation speed of the motor. Without an inverter, the AC motor

More information

Brushless Motors BLE2 Series

Brushless Motors BLE2 Series Brushless Motors BLE2 Series All New. An advanced Brushless DC package, which is both easy to use and feature rich. 3 W 6 W 12 W Evolution in Brushless Motors Introducing the BLE2 Series BLE Series models

More information

USER'S MANUAL MODEL DPD60001 MICROSTEP DRIVER PACK

USER'S MANUAL MODEL DPD60001 MICROSTEP DRIVER PACK COPYRIGHT Copyright 1997 by Anaheim Automation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,

More information

2-PHASE STEPPING SYSTEMS. Ver.5

2-PHASE STEPPING SYSTEMS. Ver.5 -PHASE STEPPING SYSTEMS Ver. DC Input Set Models DC Input Drivers Stepping Motors Motor size: mm sq. (. inch sq.) to mm sq. (. inch sq.), mm (. inch) Stepping Motors with Integrated Drivers IP Splash and

More information

OPERATING MANUAL. 2-Phase Stepping Motor Unit CSK Series

OPERATING MANUAL. 2-Phase Stepping Motor Unit CSK Series HP-7451 2-Phase Stepping Motor Unit CSK Series OPERATING MANUAL Thank you for purchasing an Oriental Motor product. This operating manual describes product handling procedures and safety precautions. Please

More information

2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE

2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE 2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE For Diaphragm Dosing Pumps FEM 1.02_.55 / FEM 1.09_.55 Controller board package, without pump: ID 160536 Operating and Installation Manual It is important to

More information

User s Manual. For M542. High Performance Microstepping Driver. Version All Rights Reserved

User s Manual. For M542. High Performance Microstepping Driver. Version All Rights Reserved User s Manual For M542 High Performance Microstepping Driver Version 1.0.2011 All Rights Reserved Attention: Please read this manual carefully before using the driver! Easy Commercial Global Technology

More information

OPERATING MANUAL. 5-Phase Stepping Motor Unit CRK Series

OPERATING MANUAL. 5-Phase Stepping Motor Unit CRK Series HP-4189-7 5-Phase Stepping Motor Unit CRK Series OPERATING MANUAL Thank you for purchasing an Oriental Motor product. This Operating Manual describes product handling procedures and safety precautions.

More information

SMD10 SMD11 SMD15 SMD30

SMD10 SMD11 SMD15 SMD30 SMD10 SMD11 SMD15 SMD30 Step Motor Drivers User Manual JVL Industri Elektronik A/S - January 1992 LB0009-02GB Revision 11th Feb 98 Contents 1.1 Introduction 2 1.2 Overview of Driver Models 3 1.3 Front

More information

MDC V, 30A Brushless Controller. User s Guide L East Orangefair Lane, Anaheim, CA

MDC V, 30A Brushless Controller. User s Guide L East Orangefair Lane, Anaheim, CA MDC150-012301 12V, 30A Brushless Controller User s Guide A N A H E I M A U T O M A T I O N 910 East Orangefair Lane, Anaheim, CA 92801 e-mail: info@anaheimautomation.com (714) 992-6990 fax: (714) 992-0471

More information

USERS GUIDE CSMD2 U440 (UNIPOLAR DRIVE) CSMD2 B440 (BIPOLAR DRIVE) CONVEX Microstep Driver FOR 2PH Step Motor < CONTENTS >

USERS GUIDE CSMD2 U440 (UNIPOLAR DRIVE) CSMD2 B440 (BIPOLAR DRIVE) CONVEX Microstep Driver FOR 2PH Step Motor < CONTENTS > CONVEX Microstep Driver FOR 2PH Step Motor CSMD2 U440 (UNIPOLAR DRIVE) CSMD2 B440 (BIPOLAR DRIVE) Manual no. CSMD2_440CE-ENG 991127 USERS GUIDE < CONTENTS > 1. Safety Cautions P.2 2. Unpacking and Inspection

More information

SR8. 2 Phase Step Motor Drive. User Manual Rev AMP & MOONS Automation

SR8. 2 Phase Step Motor Drive. User Manual Rev AMP & MOONS Automation SR8 2 Phase Step Motor Drive User Manual Rev. 1.1 AMP & MOONS Automation Contents 1 Introduction...3 1.1 Overview...3 1.2 Features...3 1.3 Block diagram...4 2 Mounting the Drive...4 3 Connections...5 3.1

More information

DC Input. Brushless Motors/AC Speed Control Motors D-117. Brushless Motors/AC Speed Control Motors D-117. BLH Series. Overview, Product Series

DC Input. Brushless Motors/AC Speed Control Motors D-117. Brushless Motors/AC Speed Control Motors D-117. BLH Series. Overview, Product Series Brushless /C Speed Control D-117 Overview, Series Brushless /C Speed Control Brushless Brushless BMU BLE BLF BX BLH Series BLH C Speed Control DSC BHF ccessories Installation D-117 D-118 Brushless BLH

More information

User s Manual-M752. Stepper Motor Driver. Version All Rights Reserved. Attention: Please read this manual carefully before using the driver!

User s Manual-M752. Stepper Motor Driver. Version All Rights Reserved. Attention: Please read this manual carefully before using the driver! User s Manual-M752 Stepper Motor Driver Version 1.0 2006 All Rights Reserved Attention: Please read this manual carefully before using the driver! Table of Contents 1. Introduction, Features and Applications

More information

SR4. 2 Phase Step Motor Drive. User Manual Rev AMP & MOONS Automation

SR4. 2 Phase Step Motor Drive. User Manual Rev AMP & MOONS Automation SR4 2 Phase Step Motor Drive User Manual Rev. 1.1 AMP & MOONS Automation Contents 1 Introduction...3 1.1 Overview...3 1.2 Features...3 1.3 Block diagram...4 2 Mounting the Drive...4 3 Connections...5 3.1

More information

DP-504/DP-508 Stepper Driver

DP-504/DP-508 Stepper Driver DP-504/DP-508 Stepper Driver User s Manual Xinje Electronic Co., Ltd. NO. DC011 20091223 1.0 DP-504/DP-508 series subdivision driver user s manual Content 1. Summary... 1 1-1. Characteristic... 1 1-2.

More information

Operation Manual. Document No.: KE KITZ EKSR Series Spring Return Type Electric Actuators. For KITZ Ball Valves

Operation Manual. Document No.: KE KITZ EKSR Series Spring Return Type Electric Actuators. For KITZ Ball Valves Document No.: KE-4041-00 Operation Manual KITZ EKSR Series Spring Return Type Electric Actuators For KITZ Ball Valves Thank you for choosing KITZ products. For safe and trouble-free function and performance

More information

BLU Series. RoHS-Compliant. Brushless DC Motor and Driver Package. Features

BLU Series. RoHS-Compliant. Brushless DC Motor and Driver Package. Features RoHS-Compliant Brushless DC Motor and Driver Package BLU Series The BLU Series combines a brushless DC motor and a panel-installation type driver, enabling speed control via simple wiring and easy operation.

More information

RoHS-Compliant Brushless Motor Systems FBL Series. Features

RoHS-Compliant Brushless Motor Systems FBL Series. Features Speed Control Systems RoHS-Compliant Brushless Motor Systems FB Series The FB Series consists of a high performance, compact, brushless motor and driver. This product is available with 75 W (1/1 HP) and

More information

DP-504/DP-508 Stepper Driver

DP-504/DP-508 Stepper Driver DP-504/DP-508 Stepper Driver User Manual WUXI XINJE ELECTRIC CO., LTD. NO. DC011 20100811 1.0 DP-504/DP-508 series subdivision driver user s manual Content 1. Summary... 1 1-1. Characteristic... 1 1-2.

More information

I. Safety precautions

I. Safety precautions . Safety precautions The items described in these instructions and on the inverter itself are very important so that you can use the inverter safely, prevent injury to yourself and other people around

More information

DP-153/DP-153-L Stepper Drive

DP-153/DP-153-L Stepper Drive DP-153/DP-153-L Stepper Drive User Manual WUXI XINJE ELECTRIC CO., LTD. NO. DC05 20120210 1.0 Catalog 1. Summary... 1 1-1. Characteristic... 1 1-2. Application... 1 1-3. Electric characters... 1 2. Operation

More information

B297SB-01-1K40. AnyWireASLINK System Product Guide. ASLINKSENSOR [Photo Interrupter type] -B297SB011K40 1/7- [Function] [Notes on Safety]

B297SB-01-1K40. AnyWireASLINK System Product Guide. ASLINKSENSOR [Photo Interrupter type] -B297SB011K40 1/7- [Function] [Notes on Safety] READER/WRITER LotNo.*** MADE JAPAN AnyWireAS System Product Guide ASSENSOR [Photo Interrupter type] B297SB-01-1K40 [Notes on Safety] Precautions that must be observed in order to use this system safely

More information

MSD Phase Step Motor Drive User Manual

MSD Phase Step Motor Drive User Manual MSD4822 2 Phase Step Motor Drive User Manual Contents 1 Introduction...3 1.1 Overview...3 1.2 Features...3 1.3 Block diagram...4 2 Mounting the Drive...4 3 Connections...5 3.1 Connector Diagram...5 3.2

More information

EVS RP6020. Instruction Manual

EVS RP6020. Instruction Manual Instruction Manual TDK Lambda BEFORE USING THE PRODUCT Be sure to read this instruction manual thoroughly before using this product. Pay attention to all cautions and warnings before using this product.

More information

Extended Panel Operation Manual RKP001Z-0

Extended Panel Operation Manual RKP001Z-0 Extended Panel Operation Manual RKP001Z-0 Table of Contents 1. NAMES AND FUNCTIONS OF MAIN PARTS...3 2. CONNECTION AND START-UP...4 3. DIMENSIONS...5 4. PROTECTION FUNCTION...6 5. SPECIFICATIONS...6 6.

More information

Operations Manual. Zero Speed Switch Sensor Model ZS09P

Operations Manual. Zero Speed Switch Sensor Model ZS09P Zero Speed Switch Sensor Model ZS09P The must be referred to for correct installation. Failure to comply with the shall void all warranties and liabilities. Overview The Phares Electronics Model ZS09P

More information

DMX-A2-DRV Integrated Advanced Step Motor Driver

DMX-A2-DRV Integrated Advanced Step Motor Driver DMX-A2-DRV Integrated Advanced Step Motor Driver DMX-A2-DRV Manual page 1 rev 3.10 COPYRIGHT 2008 ARCUS, ALL RIGHTS RESERVED First edition, May 2008 ARCUS TECHNOLOGY copyrights this document. You may not

More information

AK-G/AK-GB/AK-R/AK-RB Series

AK-G/AK-GB/AK-R/AK-RB Series 4mm/ 6mm/ 85mm Geared type/geared+rake built-in type 6mm Rotary actuator type/ Rotary actuator+rake built-in type Features Compact design and light weight with high accuracy, speed and torque Cost-effective

More information

Brushless Motors. Brushless Motors/AC Speed Control Motors. Brushless Motors/AC Speed Control Motors D-11. AC Input BX Series. AC Input BLF Series

Brushless Motors. Brushless Motors/AC Speed Control Motors. Brushless Motors/AC Speed Control Motors D-11. AC Input BX Series. AC Input BLF Series Brushless Motors/C Speed Control Motors Introduction Brushless Motors/C Speed Control Motors Brushless Motors C Input BX Series C Input BLF Series C Input BLE Series C Input BLU Series DC Input BLH Series

More information

Insulation method Zero-cross function Indicators Applicable output load Model number Phototriac coupler Yes Yes (See page 6) Main Circuit

Insulation method Zero-cross function Indicators Applicable output load Model number Phototriac coupler Yes Yes (See page 6) Main Circuit SSR with Failure Detection Function Detects failures in SSRs used for heater temperature control and simultaneously outputs alarm signals. This product supports the safe design of heater control systems,

More information

(with Class-1 AC resistive load) 3. G3PB-215B-2N-VD kW max. (25 A) G3PB-225B-3N-VD 2. G3PB-225B-2N-VD kw max. (35 A) G3PB-235B-3N-VD 2

(with Class-1 AC resistive load) 3. G3PB-215B-2N-VD kW max. (25 A) G3PB-225B-3N-VD 2. G3PB-225B-2N-VD kw max. (35 A) G3PB-235B-3N-VD 2 Solid-state Contactor (New Heat Sink Construction) G3PB Space and working time saved with new heat sink construction. Series now includes 480-VAC models to allow use in a greater range of applications.

More information

STEPPING SYSTEMS. Stepping Systems ENGLISH

STEPPING SYSTEMS. Stepping Systems ENGLISH STEPPING SYSTEMS Stepping Systems E ENGLISH STEPPING DRIVER The -phase Stepping System Stepping System Configuration Upper PLC Controller PC * Refer to the pages of driver for cable. DRIVER P~ P * Refer

More information

ZETA advanced microstep drive. Microstepping systems - the next generation... Automation. Quicker settling following a speed change

ZETA advanced microstep drive. Microstepping systems - the next generation... Automation. Quicker settling following a speed change ZETA-2 advanced microstep drive Microstepping systems - the next generation... The new ZETA series drives from Parker represent a true revolution in microstep drive design. Incorporating breakthrough techniques

More information

OPERATING MANUAL. 5-Phase Stepping Motor Unit UPK W Series

OPERATING MANUAL. 5-Phase Stepping Motor Unit UPK W Series HP-4108-4 5-Phase Stepping Motor Unit UPK W Series OPERATING MANUAL Thank you for purchasing an Oriental Motor product. This Operating Manual describes product handling procedures and safety precautions.

More information

RHINO MOTION CONTROLS

RHINO MOTION CONTROLS Installation Manual and Datasheet http://www.rhinomotioncontrols.com Page 1 [] Key Features Smooth and quiet operation at all speeds and extremely low motor heating Industrial grade performance for 2-Phase

More information

Technical Documentation

Technical Documentation Technical Documentation Product manual Holding brake controller Document: 0198441113316 Edition: V1.00, 03.2006 Important information The drive systems described here are products for general use that

More information

Pneumatic Drive Type Drill Bit Breakage Detection Sensor. DFM3 Series. The World's First!! Pneumatic-Drive Type. Catalog / Instruction Manual US.PAT.

Pneumatic Drive Type Drill Bit Breakage Detection Sensor. DFM3 Series. The World's First!! Pneumatic-Drive Type. Catalog / Instruction Manual US.PAT. Pneumatic Drive Type Drill Bit Breakage Detection Sensor DFM3 Series The World's First!! Pneumatic-Drive Type Catalog / Instruction Manual US.PAT. Pneumatic Drive Type Drill Bit Breakage Detection Sensors

More information

RoHS-Compliant. Brushless DC Motor and Driver Package BX Series

RoHS-Compliant. Brushless DC Motor and Driver Package BX Series RoHS-Compliant Brushless DC Motor and Driver Package BX Series RoHS-Compliant Brushless DC Motor and Driver Package BX Series The BX Series brushless DC motor and driver packages offer high performance

More information

The information in this chapter will enable you to: 90VAC to 50/60 Hz

The information in this chapter will enable you to: 90VAC to 50/60 Hz C H A P T E R ➃ Hardware Reference The information in this chapter will enable you to: Use this chapter as a quick-reference tool for most system specifications (dimensions and performance) Use this chapter

More information

INSTALLATION MANUAL. PRVC2 is available only for the Multi-V IV model (PRVC2 can not be installed for the previous Multi-V IV model)

INSTALLATION MANUAL. PRVC2 is available only for the Multi-V IV model (PRVC2 can not be installed for the previous Multi-V IV model) INSTALLATION MANUAL Low Ambient Control Kit Please read this installation manual completely before installing the product. Installation work must be performed in accordance with the national wiring standards

More information

Table 1: 2-pin Terminal Block J1 Functional description of BSD-02LH Module Pin # Pin Description Table 2: 10-pin Header J2 Pin # Pin Description

Table 1: 2-pin Terminal Block J1 Functional description of BSD-02LH Module Pin # Pin Description Table 2: 10-pin Header J2 Pin # Pin Description Functional description of BSD-02LH Module The BSD-02LH module is the part of the BSD-02 family of drivers. The main difference is higher microstepping resolution. The BSD-02LH is suitable for driving bipolar

More information

Hybrid Control System, Alpha Step

Hybrid Control System, Alpha Step B Hybrid Control System, Alpha Step Hybrid Control System B-1 Overview... B-2 Overview Hybrid Control System Battery-Free, Absolute Sensor Equipped AZ Series... B-16 Electric Linear Slides EZS Series AZ

More information

Please read Safety Considerations in operation manual before using. [Ai-M-42 Series] [Ai-M-56 Series] [Ai-M-60 Series] 67.5mm mm. 73.

Please read Safety Considerations in operation manual before using. [Ai-M-42 Series] [Ai-M-56 Series] [Ai-M-60 Series] 67.5mm mm. 73. i- Series 2-Phase Closed-Loop Stepper otor Features inimal heat generating, high torque motor (control voltage 55V) Higher cost-efficiency compared to conventional servo motors vailable in motor frame

More information

THT-500-A/R INSTRUCTION MANUAL TEMPERATURE AND HUMIDITY TRANSMITTER

THT-500-A/R INSTRUCTION MANUAL TEMPERATURE AND HUMIDITY TRANSMITTER INSTRUCTION MANUAL TEMPERATURE AND HUMIDITY TRANSMITTER THT-500-A/R No.THT51E1 2017.12 Thank you for purchasing our THT-500-A/R, Temperature and Humidity Transmitter (mounted within control panel). This

More information

High-efficiency AR Series DC power input Pulse input type USER MANUAL

High-efficiency AR Series DC power input Pulse input type USER MANUAL HM-60139 Stepping motor and driver package High-efficiency AR Series DC power input Pulse input type USER MANUAL Thank you for purchasing an Oriental Motor product. This manual describes product handling

More information

Outdoor UPS. User Manual. Contents. Please read carefully this manual before installing and using this product. 1 Introduction Safety...

Outdoor UPS. User Manual. Contents. Please read carefully this manual before installing and using this product. 1 Introduction Safety... Contents 1 Introduction...1 2 Safety...4 3 Product Specifications...6 Outdoor UPS User Manual 4 Installation...8 4.1 Inspection...8 4.2 Installing the UPS Cabinet...8 4.3 Connecting the Power Supply...10

More information

MBC01081 Series. Bipolar Microstep Driver. User s Guide E. Landon Drive Anaheim, CA

MBC01081 Series. Bipolar Microstep Driver. User s Guide E. Landon Drive Anaheim, CA MBC01081 Series Bipolar Microstep Driver User s Guide A N A H E I M A U T O M A T I O N 4985 E. Landon Drive Anaheim, CA 92807 e-mail: info@anaheimautomation.com (714) 992-6990 fax: (714) 992-0471 website:

More information

56 mm sq. (2.20 inch sq.)

56 mm sq. (2.20 inch sq.) 56 mm sq. (2.2 inch sq.) 1.8 /step RoHS Bipolar winding, Lead wire type Unipolar winding, Lead wire type p. 68 Customizing Hollow Shaft modification Decelerator Encoder Varies depending on the model number

More information

COMPACT BUT CUT OFF DC POWER CURRENT, POWER CAPSULE CONTACT RELAY

COMPACT BUT CUT OFF DC POWER CURRENT, POWER CAPSULE CONTACT RELAY COMPACT BUT CUT OFF DC POWER CURRENT, POWER CAPSULE CONTACT RELAY EB RELAYS (AEB) (1A type) FEATURES Compact and high capacity using double contacts in series and permanent magnet installed. (1,A/3 times)

More information