POP 4000 SERIES RIVET TOOLS

Size: px
Start display at page:

Download "POP 4000 SERIES RIVET TOOLS"

Transcription

1 POP 4000 SERIES RIVET TOOLS PRT4000 MCS4000 INSTRUCTION MANUAL Ver:2 05 Aug 2002 WARNING: ONLY TRAINED SERVICE PERSONNEL SHOULD PERFORM SERVICE PROCEDURES. IMPORTANT READ THE FOLLOWING SAFETY INSTRUCTIONS CAREFULLY

2 CONTENTS SECTION PAGE I DESCRIPTION AND MODEL IDENTIFICATION 2 II PREPARATION FOR OPERATION 3 III SERVICE PROCEDURES 4 IV DISASSEMBLY & ASSEMBLY INSTRUCTIONS 5 1 Handle Cap Assembly 5 2 Intensifier Assembly 6 3 Air Valve and Pressure Regulator Assembly 7 4 Handle Replacement 7 IV MAINTENANCE SCHEDULE 8 DISCONNECT TOOL FROM AIR SUPPLY BEFORE ATTEMPTING SERVICE. SERVICE SHOULD ONLY BE PERFORMED BY TRAINED PERSONNEL. SAFETY INSTRUCTIONS 1. It is recommended to wear eye protection when operating the tool. 2. To avoid injury do not point the tool at anyone. 3. Do not exceed recommended maximum air pressure (5.5 bar, 80psi). 4. Disconnect the tool from the air supply when not in use for an extended period of time or before proceeding with any maintenance procedures. Take care to control air hoses when disconnecting to prevent whipping. 5. Do not attempt to operate the tool with the Nose Housing removed. This exposes potential pinch points and could result in injury. 6. Do not tamper with Fill Screw. Loosened screws may result in malfunction or injury due to air or hydraulic pressure. 7. Do not operate the tool without either the deflector (PRT Option) or the collector (MCS Option) installed on the tool. Spent rivet mandrels may be forcefully ejected. 8. Always clear the tool of spent rivet mandrels before setting a new fastener. Failure to do so may result in tool jams or forceful ejection of spent mandrels. 9. Use caution when operating the tool, compressed air is released through the front of the Intensifier Chamber. Do not direct exhaust towards anyone. 10. Inspect the tool at regular intervals for damage and proper function. Replace damaged parts immediately. Do not connect a damaged tool to an air supply. 11. Use only genuine POP brand replacement parts

3 I DESCRIPTION AND MODEL IDENTIFICATION The 4000 Series tools are light weight air-hydraulic Rivet Tools capable of setting commercial blind rivets up to and including 3.2mm (1/8 ) diameter in aluminium. Two models are available. PRT4000 MCS4000 Setting Tool with mandrel deflector only. Setting Tool with automatic vacuum Mandrel Collector attached. PRT4000 and MCS4000 are supplied set up for 3.2mm (1/8 ) diameter rivets. A nosepiece is included for 2.4mm (3/32 ) rivets. Additionally, front end components can be ordered to set 2.0mm (5/64 ) Micro rivets. Refer to Set Up Procedures, Section II of this manual for more information. PACKED IN CARTON - MODELS PRT4000 and MCS4000 Part Number Part Name Data Model PRT4000 Rivet Tool Assembled (no airline) PRG Deflector Safety device - PRT4000 only PRT Spanner 8mm 19mm multi-spanner PRT Cap Spanner 52mm cap spanner PRM Hex Wrench 5mm hex wrench PRN314 Nosepiece 2.4mm (3/32 ) open end rivets AN Coupler Air line coupler Operator s Instructions MCS Version (additional items) MCS4000 MCS complete kit (see Parts List, page 10 for kit contents) SPECIFICATIONS PRT4000 MCS4000 Weight: 1.055kg (2.33 lbs.) 1.2kg (2.64 lbs.) Length: 155mm (6.10 in.) 236mm (9.2 in.) Height: 230mm (9 in.) 230mm (9 in.) Stroke: 16mm (.63 in.) 16mm (.63 in.) Pulling Force: 3.3kN (742 lbs.) 3.3kN (742 lbs.) Operating Pressure: bar (65-80 psi.) bar (65-80 psi.) Air Consumption: 0.9 litres/rivet 0.9 litres/rivet litres/min (MCS) I.1 THEORY OF OPERATION When connected to an air supply and the trigger operated, pressurized air pushes the Air Piston / Ram Assembly. The Ram Assembly forces hydraulic fluid from the reservoir in the handle into the main bore where it pushes the hydraulic piston and the attached pulling mechanism rearward. As the Pulling Jaws move towards the rear, they grip the rivet mandrel and set the rivet. Releasing the trigger enables the return spring to push the hydraulic piston forward to the starting position. The hydraulic fluid is forced back returning the Ram Assembly and Air Piston to the starting position. The compressed air used to set the rivet is exhausted through the front of the Intensifier Chamber. The hydraulic piston is fully returned, the broken rivet mandrel is released as the Jaws are forced open again by the Nosepiece. If the tool is equipped with a Mandrel Collection System (MCS models) the mandrel will be drawn out of the tool and deposited in the Collector Bottle, which should be emptied every 100 mandrels

4 II PREPARATION FOR OPERATION CAUTION: Do not connect to air supply until all tool parts are properly installed. It is recommended to wear eye protection when operating this tool. II.1 AIR SUPPLY REQUIREMENTS Use a dry, filtered air supply regulated to bar (65-80psi). It is not necessary to lubricate the air supply. Excess oil, water or debris in the air supply will necessitate more frequent tool service and significantly reduce the operating efficiency of the Mandrel Collection System. II.2 TOOL CAPABILITY 1. Select the appropriate Nosepiece from the chart below. The PRT4000 and MCS4000 tools are assembled with Nosepiece PRN414 (01) suitable for 3.2mm (1/8 ) rivets. 2. To set 2.4mm (3/32 ) rivets replace the installed Nosepiece PRN414 (01) with PRN314 (02) supplied in carton. 3. To set 2.0mm (5/64 ) Open or 3.2mm (1/8 ) Closed End rivets, additional components are needed. NOSEPIECE CHART II.3 CHANGING TOOL SET UP FOR DIFFERENT RIVET SIZES To prevent mandrel jams and maximise jaw life, it is important to install the correct Nosepiece, Jaws, Jaw Pusher and Mandrel Guide tube. Procedure 1. Place the tool in a soft-jawed vice, gripping the tool in the centre of the handle. 2. For Nosepieces PRN 314, PRN 414 and PRN 424, simply remove the Nosepiece fitted, replace with the required Nosepiece, and tighten. 3. For 2mm Micro rivets remove the installed Nosepiece and Nose Housing (03). 4. Remove the Jaw Guide (04), Jaws (05) and Jaw Pusher (06). 6. Install the correct Jaw Pusher (06). 7. Install the correct Jaws (05). 8. Re-install the Jaw Guide (04) and tighten. 9. Replace the Nose Housing (03) and tighten. 10. Install correct Nosepiece and tighten

5 II.4 OPERATION 1. Attach tool to suitable air supply. 2. Ensure the deflector (36) PRT4000, or collector (106) MCS4000, is in place before operating tool. 3. Insert a rivet mandrel into the Nosepiece. If the tool is equipped with a Mandrel Collection System (MCS4000) the rivet will be held in the tool by vacuum. 4. Position rivet into work piece. 5. Squeeze the trigger (27) to set the rivet. Once the rivet is set, release the trigger. If using a PRT4000 be sure to clear the mandrel from the tool by tipping the tool to let the mandrel slide either out of the front or out of the back of the tool. If using the MCS4000, the mandrel will be automatically extracted into the Mandrel Collector Bottle, which should be emptied every 100 mandrels. CAUTION: Read the Operator Instruction Leaflet before operating the tool. III III.1 SERVICE PROCEDURES SERVICING THE JAWS, JAW PUSHER AND JAW PUSHER SPRING Regular cleaning of the Jaws and front-end parts will prevent mandrels sticking in the Jaws and extend the Jaw life. Procedure 1. Disassemble the tool front end as described in Section II.3. Clean Jaws (05) using a brush and solvent. If jaw teeth show significant wear replace both jaws. 2. Check Jaw Pusher Spring (07) for fatigue. A new spring measures 54mm (2 1/8 ) in length. Replace spring if shorter than 46mm (1 7/8 ). 3. Thoroughly clean the inside of the Jaw Guide (04), Nose Housing (03), the Jaw Pusher (06) and wipe out debris from around other exposed parts. 4. Lightly oil Jaws (05) and Jaw Pusher (06) before reassembling. 5. Reassemble parts in reverse order. Ensure Jaw Guide (04), Nose Housing (03) and Nosepiece (01) are tightened. III.2 REPLENISHMENT OF HYDRAULIC FLUID A shortened stroke indicates minor hydraulic fluid loss. Hydraulic fluid can be replaced without fully disassembling the tool. CAUTION: The tool must be disconnected from the air supply before attempting to replenish hydraulic fluid. Procedure 1. Place the tool, inverted, in a soft-jaw vice, with the Chamber (52) pointing up. 2. Remove Chamber Cap (53) with the Cap Spanner (PRT ) provided. 3. Remove the Air Piston Assembly (51) from the Chamber. 4. Add oil into the bore at the base of the Chamber, inside the tool handle. Fill to approximately 8mm from the top of the bore. (For oil specification see page 7). 5. Temporarily replace Air Piston Assembly (51). Pump the Air Piston 2 3 times into the bore to remove air bubbles. 6. Remove Air Piston Assembly once more. Re-check oil level. If the oil level is lower, repeat the above procedure until a satisfactory oil level is achieved. 7. When the oil level is correct, replace Air Piston Assembly (51) and push firmly into place. Replace Chamber Cap (53) and tighten. 8. Rotate tool into an upright position in the vice (chamber at bottom)

6 9. Loosen Fill Screw (16) with 5mm Hex wrench (PRM530-49) provided, to remove excess oil and air bubbles. 10. After the excess oil and air has been removed, tighten Fill Screw (16) using Hex wrench provided. 11. Reconnect to Air Supply. CAUTION: Do not depress the trigger when Fill Screw (16) is loose. This will cause oil to be forced out under great pressure. If oil loss is rapid or excessive refer to Section IV of this manual for seal replacement procedures IV PRT4000 & MCS4000 DISASSEMBLY & ASSEMBLY INSTRUCTIONS IMPORTANT READ SAFETY INSTRUCTIONS ON PAGE 1 OF INSTRUCTION MANUAL DISCONNECT TOOL FROM AIR SUPPLY BEFORE ATTEMPTING SERVICE SERVICE SHOULD BE PERFORMED BY TRAINED PERSONNEL ONLY SERVICE NOTES All disassembly procedures should be performed in a clean, well-lit work area. O-rings, seals and sealing surfaces should be lightly lubricated with a white mineral oil based grease such as Lubriplate 130-AA or equivalent prior to assembly. Do not use solvents other than approved hydraulic fluid to clean O-rings or seals. FRONT END ASSEMBLY (see Changing Tool Set-Up for Different Rivet Sizes Section II.3 on page 3) IV.1.i HANDLE CAP ASSEMBLY (PRT4000) 1. Remove Deflector (36). 2. Unscrew End Cap (24) using 24mm spanner (PRT ). 3. The End Cap (24), Cap Assembly (34) and Return Spring (20) can be removed. 4. Remove O-rings (21) and (33). IV.1.ii HANDLE CAP ASSEMBLY (MCS4000) 1. Remove Collector End (110), M10 nut (103) and Collector (106). 2. Unscrew End Cap (24) using 24mm spanner (PRT ). 3. The End Cap (24), MCS Cap Assembly (101) and Return Spring (20) can be removed. 4. Remove O-rings (102), (107), (21), and (33)

7 ASSEMBLE IN REVERSE ORDER Lubricate O-rings prior to installation. IV.1.iii CONVERSION PRT4000 TO MCS4000 Remove Handle Cap assembly as per Section III.1.i replace Cap Assembly (34) with MCS Cap Assembly (101) and Deflector (36) with Collector (106). IV.2 INTENSIFIER ASSEMBLY (PNEUMATIC PISTON) 1. Loosen the Fill Screw (16). 2. Place the tool, inverted, in a soft jawed vice with the Chamber (52) facing up. 3. Remove Chamber Cap (53) using Cap Spanner (PRT ). 4. Remove Air Piston Assembly (51). 5. Ease out O-Ring (47) from Air Piston (51). 6. Place a 13mm spanner on the Lock Nut (50) and a 6mm hex wrench on the top of the Ram (43). Hold the spanner while turning the hex wrench anti-clockwise. Remove Ram from Air Piston. 7. Inspect O-Ring (47) and Rubber Cushion (45). Replace if necessary. ASSEMBLE IN REVERSE ORDER Refer to section II.2 for Hydraulic Fluid Charging Procedure. IV.3 PULLING HEAD ASSEMBLY (HYDRAULIC PISTON) 1. Secure tool upright in a soft jaw vice. 2. Remove Nose Housing (03), Jaws (05), Jaw Pusher (06), Jaw Spring (07), Jaw Guide (04). 3. Remove Handle Cap Assembly as per Section III.1.i/ii. 4. Loosen but do not remove Fill Screw (16). 5. Push the Hydraulic Piston (08) out of the rear of the tool. Take care as oil spillage will occur at this point. 6. Inspect O-Rings 2 x (18) and replace as necessary. 7. Using internal circlip pliers, remove C-Ring (10) from front of tool. Pull out Seal Sleeve (12) from front of tool. 8. Inspect all O-Rings (11), (13), (15) for damage / wear. Replace as necessary. ASSEMBLE IN REVERSE ORDER Ensure all O-Rings and the bore of the tool are lubricated. IV.4 AIR VALVE AND PRESSURE REGULATOR ASSEMBLY 1. Place tool inverted in a soft jaw vice, with Chamber (52) facing up. 2. Remove Valve Cap (56) using large flat blade screwdriver. 3. Remove Spring (61). 4. Hold tool upright and let Valve (60) drop out of tool. 5. Remove hexagonal Set Screw from Trigger Lever Cap (30) using a 2mm hex wrench. 6. Depress and hold Trigger (27), and remove Cap Assembly (30). 7. Drive out Spring Pin (31) beware of slight spring pressure. 8. Remove Valve Pusher (57), Spring (58) and Copper Washer (59), and O-Ring (37). 9. To disassemble Trigger Rod from Trigger Lever, drive out Spring Pins (28) x Remove Trigger (27) from Trigger Lever by driving out Spring Pin (26)

8 ASSEMBLE IN REVERSE ORDER -Lubricate all O-rings and seals prior to installation. IV.5 HANDLE REPLACEMENT Note: It is normally not necessary to disassemble the Handle (09) from the Chamber (52) unless either component has been damaged. 1. Loosen and remove Fill Screw (16). Drain Hydraulic fluid from tool. 2. Remove Front End Assembly (refer to section II.3 ). 3. Remove Handle Cap Assembly (section III.1.i/ii) 4. Remove Intensifier Assembly (Pneumatic Piston) (section III.2). 5. Remove Pulling Head Assembly (section III.3) 6. Remove Air Valve / Regulator Assembly (section III.4) 7. Place tool inverted, in a soft jaw vise with Chamber (52) facing up. 8. Using a special tool number (TT 1111), undo Lock Nut (42). Separate Handle (09) from Chamber (52). ASSEMBLE IN REVERSE ORDER - Lubricate all O-rings and seals prior to installation. Take care not to wrinkle or cut O-rings during assembly. APPROVED HYDRAULIC FLUIDS MOBIL - DTE26* EXXON - NUTO H-68 SHELL - TELLUS 68 TEXACO - RANDO HD

9 V MAINTENANCE SCHEDULE DAILY 1. Inspect tool and air supply hose for damage. Replace damaged parts immediately. 2. Purge air supply filters to eliminate accumulated dirt, oil and water. 3. Ensure that air pressure is regulated at 5.5 bar (80 psi). 4. Check tightness of Fill Screw (16), Nosepiece (01) and Nose Housing (03). 5. Lubricate Jaws (05), with light oil or Jaw Lube. WEEKLY OR EVERY 15,000 CYCLES 1. Dismantle Front End Assembly, thoroughly clean all parts, check Jaws (05), Jaw Pusher (06) and Jaw Pusher Spring (07) for wear and replace as needed. 2. Lightly lubricate all parts before reassembly. ANNUALLY OR EVERY 500,000 CYCLES 1. Dismantle tool and replace all seals and O-rings. Inspect all parts for wear or damage and replace as necessary. 2. Lightly lubricate all seals, O-rings and front end parts before reassembly

10 PRT / MCS 4000 PARTS DIAGRAM MANDREL COLLECTION SYSTEM - 9 -

11 PARTS LIST No. Article No Description Qty No. Article No Description Qty PRT 4000 Setting Tool O-Ring P9(1A) MCS 4000 Setting Tool O-Ring P58(1A) PRN414 Nosepiece-3.2mmØ Rivets PRT Ram Washer PRN314 Nosepiece-2.4mmØ Rivets PRT Air Piston Washer PRT Nose Housing Nut M8-T PRH820-11A Jaw Guide PRT Air Piston PRG402-8A Jaws PRT Chamber PRT Jaw Pusher PRT Air Chamber Cap PRT SUS Pipe 3.0x O-Ring G PRT Jaw Pusher Head O-Ring AN500A PRG Jaw Pusher Spring PRT Valve Cap PRT A Hydraulic Piston Assy PRT Valve Pusher PRT A Handle PRT Valve Spring C-Ring PTW PRT Copper Washer O-Ring P18(1B) PRT Valve PRT Seal Sleeve PRT Spring O-Ring P12(1B) Backup Ring PSL600CJ-13 1 ACCESSORY PARTS Pentaseal PSL600CJ-14 1 Article No Description Qty PRT Fill Screw PRN Hex Wrench PRT Fill Washer PRT Spanner O-Ring P22(1B) PRT Cap Spanner Backup Ring T2P AN Coupler PRT Return Spring O-Ring S26(1A) 1 OPTIONAL PARTS PRT Tool Hanger 1 Article No Description Qty E-Ring PRN424 Nosepiece-3.2mm Ø Closed End PRT End Cap PRN214 Nosepiece-2.0mm Ø Rivets Set Screw SS-M6* PRT Jaw Pusher 2.0mm Ø Rivets PRM Spring Pin PRG Jaws-2.0mm Ø Rivets PRT Trigger Spring Pin SPIN-3*8AW 2 MCS PARTS LIST PRT Trigger Rod 1 No. Article No Description Qty PRT Trigger Lever Cap Complete MCS Kit Spring Pin SPIN-3*14AW MCS MCS Cap Assembly PRT Trigger Lever O-Ring P7A(1A) O-Ring P16(1A) Hexagon Thin Nut M10 T PRT Cap Assembly MCS4000A-09 MCS Nozzle Set Screw SS-M4* MCS4000A-06 Collector Lock Nut PRG Deflector MCS4000A-07 Collector O-Ring PRL O-Ring 1033(1A) O-Ring P4(1A) MCS4000A-07-1 Collector Body Pentaseal PS MCS4000A-07-2 Collector Cover Backup Ring T2P MCS4000A-07-3 Collector End O-Ring P15(1B) O-Ring P16(1A) PRT Lock Nut O-Ring PRL PRT A Ram E-Ring Toothed Lock Washer TLW-A PRT A Rubber Cushion 1 Emhart Fastening Teknologies Walsall Road, Birmingham B41 1BP, UK Tel: +44 (0) Fax: +44 (0)

FPC815 Pneumatic Rivet Tool

FPC815 Pneumatic Rivet Tool WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. FPC815 Pneumatic Rivet Tool FPC Corporation warrants

More information

FPC835M Air Hydraulic Rivet Tool

FPC835M Air Hydraulic Rivet Tool WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at -800-860-3838 before returning it to the place of purchase. FPC835M Air Hydraulic Rivet Tool FPC Corporation warrants

More information

Air Hydraulic Rivet Tool

Air Hydraulic Rivet Tool WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. FPC845M Air Hydraulic Rivet Tool FPC Corporation

More information

M39075 ( IF- 1) Integra- Fuse Rivet Tool

M39075 ( IF- 1) Integra- Fuse Rivet Tool M39075 ( IF- 1) Integra- Fuse Rivet Tool Marson is making installation easier than ever with the new Marson Integra-Fuse (IF-1) It s the one-and-only tool needed for single-pull installations of open-end

More information

Cylinder Maintenance & Repair Instructions

Cylinder Maintenance & Repair Instructions Cylinder Maintenance & Repair Instructions PENINSULAR CYLINDER CO. Model HP High Pressure Hydraulic Cylinders Proximity Switch & Non Proximity Switch Designs - High Pressure NFPA Hydraulic Cylinder ( 5,000

More information

Rivet Tool PRS1060LS. Instruction Manual

Rivet Tool PRS1060LS. Instruction Manual Rivet Tool Instruction Manual This rivet tool is exclusively for pop rivets. Read this manual thoroughly before using the rivet tool, and keep it in a handy place where rivet operator can refer to it any

More information

GBP784B INSTALLATION TOOL

GBP784B INSTALLATION TOOL GBP784B INSTALLATION TOOL GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP. 14500 Barber Drive (586) 771-7664 Warren, Mi 48088 (586) 771-2665 Fax e-mail:solutions@gagebilt.com / www.gagebilt.com TABLE

More information

RH160E. Rivet Nut setting Tool (Spin /Pull) Instructions & Parts List

RH160E. Rivet Nut setting Tool (Spin /Pull) Instructions & Parts List RH160E Rivet Nut setting Tool (Spin /Pull) Instructions & Parts List This spin-pull tool automatically threads the fastener onto the mandrel. Press the trigger just once and the fastener is installed.

More information

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2 SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER

More information

GB7624 GAGE BILT MADE IN U.S.A. HYDRAULIC INSTALLATION TOOL

GB7624 GAGE BILT MADE IN U.S.A. HYDRAULIC INSTALLATION TOOL GB7624 HYDRAULIC INSTALLATION TOOL PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT

More information

Safety, Operation and Maintenance Instructions For Long & Short Nose Upholstery Air Stapler (NS10 & NS11)

Safety, Operation and Maintenance Instructions For Long & Short Nose Upholstery Air Stapler (NS10 & NS11) Safety, Operation and Maintenance Instructions For Long & Short Nose Upholstery Air Stapler (NS10 & NS11) Important: Drop 3 drops of oil into the stapler air inlet BEFORE first use. See page 2. Please

More information

SUMP PUMP ASP-25 OPERATION & MAINTENANCE GUIDE

SUMP PUMP ASP-25 OPERATION & MAINTENANCE GUIDE SUMP PUMP ASP-25 OPERATION & MAINTENANCE GUIDE Operation & Maintenance Guide OPERATION: ASP-25 pneumatic pump is designed to remove water from trenches, ditches, manholes, industrial sumps and excavations.

More information

Hydro-Pneumatic Power Tool

Hydro-Pneumatic Power Tool Service Manual Original Instruction Hydro-Pneumatic Blind Rivet Tool ProSet XT3 Blind Rivet Tool - 76003 Hydro-Pneumatic Power Tool Fig. 1 3 3 2 4 & 5 1 2 1 6 7 Fig. 2 8 1p 1n 1l 1o 1m 1k 1j 1h 1i 1f 1g

More information

Servicing the Tool. Service Kit SERVICE KIT. For all servicing we recommend the use of the service kit (part number (S)).

Servicing the Tool. Service Kit SERVICE KIT. For all servicing we recommend the use of the service kit (part number (S)). Servicing the Tool Service Kit For all servicing we recommend the use of the service kit (part number 07900-04750(S)). SERVICE KIT ITEM PART Nº DESCRIPTION Nº OFF ITEM PART Nº DESCRIPTION Nº OFF 07900-00002

More information

USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool

USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool Additional copies of this manual are available at: USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool 4068 Hydro-Pneumatic Blind Rivet Nut and Stud Installation Tool

More information

Manual & Power Tools.

Manual & Power Tools. Manual & Power Tools www.emhart.com POPNut Manual & Power Tools The NEW range of POPNut Manual Tools are ideal for a wide range of applications including light engineering work, site work and repair &

More information

Shock Absorber Rebuild Manual

Shock Absorber Rebuild Manual Shock Absorber Rebuild Manual Model PODIUM RC3 FOX RACING SHOX 130 Hangar Way, Watsonville, CA 95076 PHONE 800.369.7469 FAX 831.768.7026 Email: psservicemw@ridefox.com Website: www.ridefox.com Disclaimer

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS SETTING TOOL FOR RIVKLE BLIND RIVET NUTS AND STUDS CONTENTS I TOOL DESCRIPTION... p 2 II ACCESSORIES... p 4 III TOOL USE... p 6 IV MAINTENANCE... p12 V TROUBLESHOTTING AND SOLUTIONS...

More information

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,

More information

Maintenance Information

Maintenance Information 16573347 Edition 2 February 2014 Air Grinder Series 88H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

INTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco

INTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco Rockcrawler Steering Shop Manual page1 The following is from the Ford 1978 Truck Shop Manual, Volume 1 Chassis. It is provided here as a courtesy to classic Ford owners who would like to perform their

More information

User Instruction Manual ZT-1017-VS ZT-6000-VS

User Instruction Manual ZT-1017-VS ZT-6000-VS User Instruction Manual ZT-1017-VS ZT-6000-VS FOR SALES, SERVICE OR TECH SUPPORT CALL: 1800-BUY-RIVET or 1-800-289-7483 CONTENTS Safety Page 3 Specifications Page 3 Preparing the tool for service Page

More information

Maintenance Information

Maintenance Information 16573370 Edition 2 February 2014 Air Grinder 99V Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Instruction Manual Model# RK-8000M

Instruction Manual Model# RK-8000M Instruction Manual Model# RK-8000M For sales, service or support call your local distributor or: 1800-BUY-RIVET or 1-800-289-7483 www.rivet.com CONTENTS Features Page 3 Safety Page 3 Specifications Page

More information

4069 Operating Instructions

4069 Operating Instructions 4069 Operating Instructions SETTING TOOL FOR RIVKLE BLIND RIVET NUTS AND STUDS CONTENTS I TOOL DESCRIPTION... p 2 II ACCESSORIES... p 4 III TOOL USE... p 6 IV MAINTENANCE... p12 V TROUBLESHOTTING AND SOLUTIONS...

More information

SD Bendix E-12 & E-15 Dual Brake Valve DESCRIPTION

SD Bendix E-12 & E-15 Dual Brake Valve DESCRIPTION SD-03-6 Bendix E- & E-15 Dual Brake Valve TREADLE UPPER BODY ASSEMBLY PRIMARY DELIVERY ( ) 1 SECONDARY DELIVERY ( ) LOWER BODY ASSEMBLY MOUNTING PLATE PRIMARY SUPPLY ( SUP-1) PRIMARY SUPPLY ( SUP-) PRIMARY

More information

PACKING, HANDLING, TRANSPORTING AND STORING MOTORS

PACKING, HANDLING, TRANSPORTING AND STORING MOTORS PACKING, HANDLING, TRANSPORTING AND STORING MOTORS Make sure that the shaft of the motor is not loaded in any way and is protected from knocks. Axial loads or shocks may easily damage the bearings inside

More information

EQUALIZER International Limited 10T(I) Integral Hydraulic Spreading Wedge Repair Instruction Manual

EQUALIZER International Limited 10T(I) Integral Hydraulic Spreading Wedge Repair Instruction Manual EQUALIZER International Limited 10T(I) Integral Hydraulic Spreading Wedge Repair Instruction Manual INDEX THE EQUALIZER 10T(I) Integral Hydraulic Wedge SECTION CONTENTS PAGE NO (S) 03 04 05 06 07 08 09

More information

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.

More information

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP

OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP PAGE 1 OF 10 OPERATING INSTRUCTIONS & SERVICE MANUAL BLUE MAX II HYDROSTATIC TEST PUMP EFFICIENT, EASY OPERATION Air operated pump Wide range of pressures and volumes Easy to operate controls Output pressure

More information

GRSM17 Pneumatic Center Punch Tool Owner s Manual and Operating Instructions

GRSM17 Pneumatic Center Punch Tool Owner s Manual and Operating Instructions Owner s Manual and Operating Instructions Table of Contents Page Information 2 Safety Guidelines and Warranty 3 Overview and Installation 4 Air System Requirements 5 Setting Controls 6 Installing Clamps

More information

Maverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.0 SHOCK SERVICE MANUAL

Maverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.0 SHOCK SERVICE MANUAL Maverick American 3085 Bluff Street Boulder, CO 80301 Tel: 303-415-0370 Fax: 303-415-0676 www.maverickamerican.com ML7.0 SHOCK SERVICE MANUAL 1. OVERVIEW 1.1. The Maverick ML7.0 rear shock is an oil damped

More information

Air Operated 1:1 Oil Ratio Pump OP-11

Air Operated 1:1 Oil Ratio Pump OP-11 INSTRUCTION MANUAL Air Operated 1:1 Oil Ratio Pump OP-11 Congratulations on purchase of this World Class Air Operated Oil Ratio Pump! S1221, Rev C World-class Industrial Oil Dispensing pumps with guaranteed

More information

AIR/HYDRAULIC INJECTION GUN MODEL INSTRUCTIONS

AIR/HYDRAULIC INJECTION GUN MODEL INSTRUCTIONS I. OPERATION & DESCRIPTION The Air / Hydraulic Injection Gun is a high-pressure tool that should be used with caution and according to these instructions. IMPORTANT: The Gun is 0,000 psi rated. Do not

More information

WCI-20 Power-Pak Coldwork Hydraulic Power Supply Rev B

WCI-20 Power-Pak Coldwork Hydraulic Power Supply Rev B WCI-20 Power-Pak Coldwork Hydraulic Power Supply Rev B OM-PS-9303-2 Seattle, Washington WCI-20 Power Pak Manual Table of Contents Section 1 Introduction 1.1 Introduction... 1 1.2 Safety Precautions...

More information

Swirl Wheelbase and Interface Workshop Manual.doc

Swirl Wheelbase and Interface Workshop Manual.doc Swirl WHEELBASE AND INTERFACE WORKSHOP MANUAL IMPORTANT Please read these instructions carefully Before attempting to maintain the Wheelbase or Interface Document No: 056-02 v3 Page 1 of 34 June 2018 Fig

More information

Pressure Relief Valve Maintenance Manual

Pressure Relief Valve Maintenance Manual Technical Manual 1098T Pressure Relief Valve Maintenance Manual Farris Engineering Division of Curtiss-Wright Flow Control Corporation TABLE OF CONTENTS - Manual Revision 0 Introduction & Safety Tips...

More information

Operation and Maintenance Guide Pneumatic Piston Scabbler

Operation and Maintenance Guide Pneumatic Piston Scabbler Operation and Maintenance Guide Pneumatic Piston Scabbler X2 1SC, 1SC STD 3SC, 3SC STD Read this manual carefully before installing, operating or servicing this Pneumatic Piston Scabbler. It s the responsibility

More information

Instruction Manual Model# RK-187

Instruction Manual Model# RK-187 Instruction Manual Model# RK-187 FOR SALES, SERVICE OR TECH SUPPORT CALL: 1800-BUY-RIVET or 1-800-289-7483 CONTENTS Features Page 3 Safety Page 3 Specifications Page 3 Air supply Page 4 Operation Page

More information

RIV302-E Heavy Duty Riveter / 39062

RIV302-E Heavy Duty Riveter / 39062 RIV302-E Heavy Duty Riveter / 39062 This durable air/hydraulic riveter, with its fully adjustable vacuum system that holds the rivet in the nosepiece, allowing the operator to rivet at any angle with one

More information

SAI GM Series Piston Hydraulic Motor Crankshaft Design Radial Piston Motors

SAI GM Series Piston Hydraulic Motor Crankshaft Design Radial Piston Motors SAI GM Series Piston Hydraulic Motor Crankshaft Design Radial Piston Motors www.chinawinches.cn (Dimension: inch) Brief Performance Table of Sai GM Series Piston Hydraulic Motor (Full range GM05- GM9 series)

More information

Work shop manual. Öhlins Steering damper Road & Track

Work shop manual. Öhlins Steering damper Road & Track Work shop manual Öhlins Steering damper Road & Track Including: Introduction Safety instructions Dismantling the steering damper Assembling the steering damper Filling oil Introduction All of Öhlins advanced

More information

SERVICE INSTRUCTIONS Air Motor

SERVICE INSTRUCTIONS Air Motor SERVICE INSTRUCTIONS Air Motor 338905 DESCRIPTION The air motor has a 3" diameter piston with a -5/8" stroke. When the pump-tube upper packing is not incorporated into the air motor, the air motor is considered

More information

Service Sheet SSJ0452P. J0452 Coupler with Pump API Coupler

Service Sheet SSJ0452P. J0452 Coupler with Pump API Coupler Sheet:, 17/04/12, Rev: 2 As a part of a continuous commitment to product development the company reserves the right to alter the specification of its products without prior notice J0452 Coupler with Pump

More information

Eclipser 2500/2800 OPERATING MANUAL. and Continuous Coil (CC) Clipping System. ENCORE (EA) ECLIPSER 2500 and 2800 SERIES

Eclipser 2500/2800 OPERATING MANUAL. and Continuous Coil (CC) Clipping System. ENCORE (EA) ECLIPSER 2500 and 2800 SERIES Eclipser 2500/2800 and Continuous Coil (CC) Clipping System Encore Eclipser 2500 Series (Green) Hartco Eclipser 2500 (Black) not shown OPERATING MANUAL ENCORE (EA) ECLIPSER 2500 and 2800 SERIES Pneumatic

More information

MOREHOUSE INSTRUMENT COMPANY, INC. 60,000 LBS CAPACITY AIRCRAFT PART NUMBER SCALE S FORCE CALIBRATION PRESS PART NO.

MOREHOUSE INSTRUMENT COMPANY, INC. 60,000 LBS CAPACITY AIRCRAFT PART NUMBER SCALE S FORCE CALIBRATION PRESS PART NO. INDEX 1. GENERAL SPECIFICATION AND DRAWING 804000-03... 2 2. ASSEMBLY INSTRUCTIONS... 5 3. OPERATING INSTRUCTIONS... 6 4. MAINTENANCE INSTRUCTIONS... 7 5. CERTIFICATE OF CAPACITY LOAD TEST AND OVERLOAD...

More information

SC-400, SC-550, SC-650 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK

SC-400, SC-550, SC-650 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK REV D: 0/8 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. ALL PURPOSE BREAKING SAW

More information

Hard Seat Fluid Pressure Regulator

Hard Seat Fluid Pressure Regulator Instruction Sheet P/N 04742-02 Description The Nordson hard seat fluid pressure regulator is designed for use with abrasive coatings. The regulator body is constructed of stainless steel with a nickel-plated

More information

INSTALLATION AND MAINTENANCE OF TOP LOADING ARM

INSTALLATION AND MAINTENANCE OF TOP LOADING ARM INSTALLATION AND MAINTENANCE OF TOP LOADING ARM D TABLE OF CONTENTS 1. INTRODUCTION 04 2. SPECIFICATION OF THE REDLANDS LOADING ARM 04 3. INSTALLING THE LOADING ARM 3.1. Installation Procedures 05 4.

More information

JARVIS. Model HTC -80 Hog Toe Cutter

JARVIS. Model HTC -80 Hog Toe Cutter Model HTC -80 Hog Toe Cutter HTC -80 Standard HTC -80 Pistol Grip EQUIPMENT SELECTION... Ordering No. HTC--80 Standard... 4025061 HTC--80 Pistol Grip... 4025100 HTC--80 Pistol Grip Long... 4025114 without

More information

Disassembly Instructions hp. Dynafile II Models: 40352, 40353

Disassembly Instructions hp. Dynafile II Models: 40352, 40353 Disassembly Instructions - 0.4 hp. Dynafile II Models: 40352, 40353 Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever

More information

Maintenance Information

Maintenance Information 51984144 Edition 6 May 2014 Air Paving Breaker MX60 & MX90 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Model 210HP Beadbreaker

Model 210HP Beadbreaker 00020HP:99900657: 2040409 Model 20HP Beadbreaker PARTS AND SERVICE MANUAL IOWA MOLD TOOLING CO., INC. BOX 89, GARNER, IA 50438-089 TEL: 64-923-37 TECHNICAL SUPPORT FAX: 64-923-2424 MANUAL PART NUMBER 99900657

More information

Maintenance Information

Maintenance Information 16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

GB2620 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL

GB2620 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL GB2620 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)

More information

rings used in the TuckAway Electric Monitor (#3352)

rings used in the TuckAway Electric Monitor (#3352) STYLE 3352 O-Ring Ring Replacement Guide The following tools & materials are required for disassembly & servicing of the O-rings rings used in the (#3352) 5/64 Allen wrench 7/64 Allen wrench* 3/16 Allen

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts

More information

OTECO INC. 2 RESET RELIEF VALVE 2 L.P.T. INLET & OUTLET INSTALLATION & MAINTENANCE MANUAL PART NO

OTECO INC. 2 RESET RELIEF VALVE 2 L.P.T. INLET & OUTLET INSTALLATION & MAINTENANCE MANUAL PART NO Page 1 of 9 OTECO INC. 2 RESET RELIEF VALVE 2 L.P.T. INLET & OUTLET INSTALLATION & MAINTENANCE MANUAL PART NO. 130250 Page 2 of 9 TABLE OF CONTENTS 1. PERIODIC MAINTENANCE 2. SPARE PARTS LIST 3. PROCEDURES

More information

Maintenance Information

Maintenance Information 80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing

More information

A REPAIR KIT PART NUMBER IS AVAILABLE AND CONTAINS ALL THE PARTS NORMALLY REPLACED DURING A STANDARD MAINTENANCE REPAIR.

A REPAIR KIT PART NUMBER IS AVAILABLE AND CONTAINS ALL THE PARTS NORMALLY REPLACED DURING A STANDARD MAINTENANCE REPAIR. AZ Pump Instructions PUMP NOT RUNNING PROPERLY: Check to be sure air pressure is reaching the pump, check to be sure air filter is not clogged; clean or replace as required. Check to be sure fluid filter

More information

ORIGINAL INSTRUCTIONS G715A. Pneumatic-hydraulic Riveter E. Warner Ave Santa Ana, CA

ORIGINAL INSTRUCTIONS G715A. Pneumatic-hydraulic Riveter E. Warner Ave Santa Ana, CA ORIGINAL INSTRUCTIONS G715A Pneumatic-hydraulic Riveter 1224 E. Warner Ave Santa Ana, CA 92705 www.cherryaerospace.com DESCRIPTION The Cherry G715A Pneumatic-Hydraulic Riveter is designed specifically

More information

Maintenance Information

Maintenance Information 16575243 Edition 2 October 2013 Air Screwdrivers 1R Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

VALVE AND PLUMBING KIT NEW HOLLAND 7310 LOADER NEW HOLLAND TRACTORS

VALVE AND PLUMBING KIT NEW HOLLAND 7310 LOADER NEW HOLLAND TRACTORS ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT NEW HOLLAND 73 LOADER NEW HOLLAND TRACTORS MODEL 2WD FWA LESS CAB WITH CAB TT55 X X X TT75 X X X Valve and plumbing kit can be installed

More information

SD Bendix E-7 Dual Brake Valve DESCRIPTION OPERATION APPLYING: NORMAL OPERATION - PRIMARY CIRCUIT PORTION

SD Bendix E-7 Dual Brake Valve DESCRIPTION OPERATION APPLYING: NORMAL OPERATION - PRIMARY CIRCUIT PORTION SD-03-818 Bendix E-7 Dual Brake Valve DESCRIPTION The Bendix E-7 dual brake valve is a suspended, pedal-operated type brake valve with two separate supply and delivery circuits for service and emergency

More information

Genesis Double Adjustable Shock Assembly and Repair

Genesis Double Adjustable Shock Assembly and Repair Genesis Double Adjustable Shock Assembly and Repair General Operating Description The Genesis Adjustable Shock is adjusted by moving one or both of two bypassing sliding valves. These valves slide longitudinally

More information

Service Manual. Balanced Piston First Stage

Service Manual. Balanced Piston First Stage Service Manual Balanced Piston First Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Balanced Piston First Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS CLEANING AND LUBRICATION...

More information

HPB45 and HPB55 Series Hydraulic Paving Breakers

HPB45 and HPB55 Series Hydraulic Paving Breakers SERVICE MANUAL HPB45 and HPB55 Series Hydraulic Paving Breakers Serial Codes GMN, GMP, GMR, and GMT Read and understand all of the instructions and safety information in this manual before operating or

More information

Maintenance Information

Maintenance Information 04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

VLW18TE, VLW18TI HYDRAULIC VERTICAL LIFTING WEDGES. Operator Instruction Manual INNOVATION IN ITS MOST FUNCTIONAL FORM

VLW18TE, VLW18TI HYDRAULIC VERTICAL LIFTING WEDGES. Operator Instruction Manual INNOVATION IN ITS MOST FUNCTIONAL FORM VLW18TE, VLW18TI HYDRAULIC VERTICAL LIFTING WEDGES Operator Instruction Manual info@equalizerinternational.com www.equalizerinternational.com INNOVATION IN ITS MOST FUNCTIONAL FORM INDEX SECTION CONTENTS

More information

EXOTHERMIC CUTTING EQUIPMENT

EXOTHERMIC CUTTING EQUIPMENT EXOTHERMIC CUTTING EQUIPMENT Objectives By the end of this session, you will be able to: Identify the difference between the Arcair packages that are available to EU customers. Recognise the main components

More information

Disassembly Instructions hp. Mini-Dynafile II

Disassembly Instructions hp. Mini-Dynafile II Disassembly Instructions - 0.4 hp. Mini-Dynafile II Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever to deplete the

More information

20 TONNE HYDRAULIC PRESS MODEL NO: CSA20FBT

20 TONNE HYDRAULIC PRESS MODEL NO: CSA20FBT 20 TONNE HYDRAULIC PRESS MODEL NO: CSA20FBT PART NO: 7614058 OPERATION & MAINTENANCE INSTRUCTIONS WARNING: Read these instructions before using the press GC0516 INTRODUCTION Thank you for purchasing this

More information

767 Hydraulic Hand Pump

767 Hydraulic Hand Pump INSTRUCTION MANUAL 767 Hydraulic Hand Pump Serial Code ABM Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product

More information

Instruction Manual Model# RK-8000S

Instruction Manual Model# RK-8000S Instruction Manual Model# RK-8000S FOR SALES, SERVICE OR TECH SUPPORT CALL: 1800-BUY-RIVET or 1-800-289-7483 CONTENTS Features Page 3 Safety Page 3 Specifications Page 3 Air supply Page 4 Operation Page

More information

SW14.5TI INTEGRAL HYDRAULIC FLANGE SPREADING WEDGE. Repair Manual INNOVATION IN ITS MOST FUNCTIONAL FORM

SW14.5TI INTEGRAL HYDRAULIC FLANGE SPREADING WEDGE. Repair Manual INNOVATION IN ITS MOST FUNCTIONAL FORM SW14.5TI INTEGRAL HYDRAULIC FLANGE SPREADING WEDGE Repair Manual info@equalizerinternational.com www.equalizerinternational.com INNOVATION IN ITS MOST FUNCTIONAL FORM INDEX SECTION CONTENTS PAGE NO. 1

More information

A-320 Balanced 1st Stage

A-320 Balanced 1st Stage Technical Manual A-320 Balanced 1st Stage A Manual for Repair and Maintenance Technicians View: Select Full Screen mode to use page arrows. FEATURES Extra durable satin chrome plated brass body. Fully

More information

EURO BEAD BREAKER MODEL # Instruction Manual Parts Breakdown

EURO BEAD BREAKER MODEL # Instruction Manual Parts Breakdown EURO BEAD BREAKER MODEL #10107 Instruction Manual Parts Breakdown Operation WARNING The optional air/hydraulic pump is capable of generating fluid pressure up to 10,000 PSI. Keep both hands on the handles

More information

TRIM AND TILT TABLE OF CONTENTS TRIM AND TILT

TRIM AND TILT TABLE OF CONTENTS TRIM AND TILT TRIM AND TILT TABLE OF CONTENTS SERVICE CHART................................................................... 326 SYSTEM DESCRIPTION............................................................. 328

More information

STOP. 44" High Speed Sweeper. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts

STOP. 44 High Speed Sweeper. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts Operator's Manual STOP 44" High Speed Sweeper Model No. 486.029 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product, read this manual and

More information

Audi-Larm TM Audible Alarm: AirHawk II Air Mask

Audi-Larm TM Audible Alarm: AirHawk II Air Mask Audi-Larm TM Audible Alarm: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 011 (L) Rev. 0 MSA 2010 Prnt. Spec. 10000005389(I) Mat. 10104323 Doc. 10104323 REPLACEMENT KITS AND PARTS LIST Item P/N Description

More information

Baumann Sanitary Diaphragm Angle and Inline Control Valve

Baumann Sanitary Diaphragm Angle and Inline Control Valve Instruction Manual 84000 Valve Baumann 84000 Sanitary Diaphragm Angle and Inline Control Valve Contents Introduction... 1 Scope of Manual... 1 Safety Precautions... 2 Maintenance... 2 Flow Direction...

More information

Maintenance Information

Maintenance Information 80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 3 in. (77 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20346, 3M Overhaul Service Kit, contains all the replacement parts that naturally wear

More information

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS WITH HYDRAULIC CONTROL PACKAGE PART NUMBER: SE-023 REVISION:

More information

MP-4V Heavy Duty Riveter / 39048

MP-4V Heavy Duty Riveter / 39048 MP-4V Heavy Duty Riveter / 39048 This newly designed heavy-duty air/hydraulic riveter is ergonomically designed with the professional in mind. The lightweight 3.7 lbs. well balanced MP-4V includes a Vacuum

More information

GMR-S and GMR40-S Disc Brake Caliper - Spring Applied, Air Released

GMR-S and GMR40-S Disc Brake Caliper - Spring Applied, Air Released (GMR) 9 (GMR) ø GMR-S and GMR-S Disc Brake Caliper - Spring Applied, Air Released DB Nominal dimensions given. For specific dimensions please contact Twiflex Limited. For GMR Mk caliper details see DB

More information

OWI 35C-7/ 35C-7H PIPE SPINNER

OWI 35C-7/ 35C-7H PIPE SPINNER OWI 35C-7/ 35C-7H PIPE SPINNER OIL WORKS, INC.. manufactures the OWI 35C-7 pipe spinner in Pneumatic and Hydraulic Versions at our facility in Odessa, TX. We offer new and rebuilt units, and stock a full

More information

MODEL 25-OM-10-C & 25-OA-10-C HYDRAULIC BOOSTER

MODEL 25-OM-10-C & 25-OA-10-C HYDRAULIC BOOSTER SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.powerteam.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031

More information

SW9TM, SW14.5TI, SW15TE

SW9TM, SW14.5TI, SW15TE SW9TM, SW14.5TI, SW15TE FLANGE SPREADING WEDGES Operator Instruction Manual info@equalizerinternational.com www.equalizerinternational.com INNOVATION IN ITS MOST FUNCTIONAL FORM INDEX SECTION CONTENTS

More information

OPERATING INSTRUCTIONS AND SERVICE MANUAL

OPERATING INSTRUCTIONS AND SERVICE MANUAL OPERATING INSTRUCTIONS AND SERVICE MANUAL 55NAL--270-4 55NL--724-4 55RNL-2-LS-4- COMPLETE TOOL MODEL NO. CODE NO. 55NAL--270-4 20270 55NL--724-4 220724 READ SAFETY RECOMMENDATIONS 55RNL-2-LS-4-24089 BEFORE

More information

Section 5. Maintenance. Risk of Burns. Relieving Pressure. Important when Using Cleaning Agents. Maintenance 5-1

Section 5. Maintenance. Risk of Burns. Relieving Pressure. Important when Using Cleaning Agents. Maintenance 5-1 5-1 Section 5 WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. NOTE: is an important

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

Service Tools. Service and Repair Manual Model 900/950/990 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION ITEM PART NO.

Service Tools. Service and Repair Manual Model 900/950/990 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION ITEM PART NO. 12 1 3 2 4 5 8 10 6 7 9 11 14 24 12 13 17 22 29 18 23 25 19 26 15 20 27 21 16 22 33 37 38 32 31 36 30 34 35 40 41 42 43 ITEM PART NO. DESCRIPTION 1 9170 0231 30 LONG ALLEN KEY 2 9170 0737 20 3/32 PIN PUNCH

More information

Actuator Maintenance Manual, E-Type size 8 to 150

Actuator Maintenance Manual, E-Type size 8 to 150 English Actuator Maintenance Manual, E-Type size 8 to 150 Precautions - Warning Always take care to follow this manual in order to correctly maintain the TruTorq actuators. Before removing the actuator,

More information

Plus ESG45GL Battery-powered Cable Cutter

Plus ESG45GL Battery-powered Cable Cutter INSTRUCTION MANUAL Serialnummer GATOR Plus ESG45GL Battery-powered Cable Cutter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool.

More information

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS 82-L0352 REV 8 4-27-2011 WARNING! HYDRAULIC COMPONENTS CAN CAUSE SERIOUS INJURY OR DEATH IF PROPER SAFETY PRECAUTIONS ARE

More information

SERIES OPERATION AND MAINTENANCE MANUAL

SERIES OPERATION AND MAINTENANCE MANUAL SERIES OPERATION AND MAINTENANCE MANUAL This manual CONTAINS IMPORTANT WARNINGS, S and OTHER INSTRUCTIONS. Read and understand the instruction manual Carefully, before use and retain it for reference.

More information

SD Bendix Manual Slack Adjusters DESCRIPTION ADJUSTING MECHANISM OPERATION

SD Bendix Manual Slack Adjusters DESCRIPTION ADJUSTING MECHANISM OPERATION SD-05-1200 Bendix Manual Slack Adjusters WORM SHAFT (LOCK SCREW) FIGURE 1 - POSITIVE LOCK TYPE SLACK ADJUSTER DESCRIPTION In an s-cam type foundation brake, the final link between the pneumatic system

More information

CROSBY SERIES BP OMNI-TRIM PRESSURE RELIEF VALVES INSTALLATION, MAINTENANCE AND ADJUSTMENT INSTRUCTIONS

CROSBY SERIES BP OMNI-TRIM PRESSURE RELIEF VALVES INSTALLATION, MAINTENANCE AND ADJUSTMENT INSTRUCTIONS Before installation these instructions must be read fully and understood cause misalignment of the valve parts. It is recommended that the valves be left in their original shipping containers and that

More information