DC-44 and DC-88 Series Non Spring Return Electronic Actuator Installation Instructions

Transcription

1 "" Delta Control Products, Inc. West Rose Garden Lane Phoenix, Z DC-44 and DC-88 Series Non Spring Return Electronic ctuator Installation Instructions Product Description This installation instruction describes the steps for direct-coupled mounting of the Delta DC-44 and DC-88 Series non-spring return rotary electronic valve and damper actuator. Parts Included for Damper Mounting a) ctuator b) Position indicator c) Mounting bracket d) Mounting screws a. e) mm hex key f) Coupling insert g) Handle (included on valve assemblies only) g. b. d. e. f. c. Required Tools mm hex key (provided) 4 mm (5/-in.) drill bit and drill Phillips screwdriver Marker or pencil Damper Mounting Instructions NOTE: Place the actuator on the damper shaft so that the front of the actuator is accessible. The label is on the front side.. Determine whether the damper blades will rotate clockwise or counterclockwise to open.. If the blades will rotate counter clockwise, slide the manual override switch to manual, and move the adjustment lever to the right. Return the switch to automatic. See Figure 5. To mount a (modulating) DCM-44/88 set the Dual In-line Package (DIP) switches to the required positions by following these steps:. ccess the DIP switches by raising the tab on the lower left side of the actuator. Refer to Figure. The factory setting is clockwise, with a direct-acting feedback signal (Refer to page 5 of this document for complete DIP switch setting instructions).. Close the tab over the DIP switches. To mount a (-position) DC-44-T/88 for counter clockwise rotation, be sure to follow the instructions for direction of rotation located in the wiring section when wiring the actuator to the controller. Clockwise to Open "" Counter Clockwise to Open DIP Switches DIP Switches Modulating Units Only Figure. Setting the Direction of Rotation Modulating Units Only

2 mm f 5 b 4 Figure. Mounting the ctuator to the Damper Shaft / CENTER THE MOUNTING RCKET IN THE SLOT CUTION: THESE HOLES FOR USE WITH CCESSORY KITS ONLY. DO NOT USE IN THE INSTLLTION OF DIRECT-COUPLED PPLICTIONS /! 4 mm 5/ in. c d d Figure 4. ttaching the Mounting racket Manual Override To move the damper blades and lock the position with no power present:. Slide the red manual override switch toward the back of the actuator.. Make adjustments to the damper position.. Slide the red manual override switch toward the front of the actuator. Once power is restored, the actuator returns to automated control. MNUL UTO Figure 5. Manual Override DC-44/88 Installation Instructions Page of 5

3 Dual uxiliary Switch Setting For product numbers with suffix only. Factory setting: = 5 = 85 Use a flat blade screwdriver to adjust the switch. The long arm of the X points the setting. Manually turn the red ring of the switch. The narrower tab on ring points to the setting. The scale for the auxiliary switch setting is valid only when the actuator is in position and clockwise rotation. ctuator Scale CW djustment range for Switches and Setting Interval: 5 Switching hysteresis ctuator Scale CCW Figure 6. uxiliary Switch djustment Mechanical Range djustment mm > Figure 7. Moving the Mechanical Range Stop. Loosen the stop set screw.. Move the screw along the track to the desired position, and fasten it in place.. To use the entire to V input signal to control the adjusted range, raise the tab located on the lower lefthand side of the actuator and locate the DIP switches. See Figure Set the self-adapt DIP switch to (On). 5. Close the tab over the DIP switches. For example, If you set the locking screw at 7 and turn the self-adapt switch ON, a 5V input signal will drive the damper to 5 (5% of its adjusted range). Factory Setting Shown = Off Figure 8. Self-dapt Switch in the On Position Slope and Offset djustment For DCM4-44-Z DCM4-88-Z only. Factory setting: Span U = Offset Uo = Use a flat-blade screwdriver to make adjustments. The long arm of the X points the setting. U Ys Uo 6 4 U 5 V Uo 4 Figure 9. DC-44/88 Installation Instructions Page of 5

4 Wiring ll wiring must conform to NEC and local codes and regulations. Use earth ground isolating step-down Class transformers. Do not use auto transformers. DC4-44-T and DC4-88-T Series 4 VC Three Position Control Direction of Damper Rotation DC-44/88 If the damper blades turn counterclockwise to open (CCW), reverse the 6 (violet) and 7(orange) wires at the controller. NEUT 4 VC 7 (Orange) 6 (Violet) VC 7 (Red) Earth Ground Isolating Class Transformer for 4 VC Power Figure. Three Position Control Table. Three position Control 4 VC 6 7 S Supply (SP) G Red M S S S5 S6 6 7 Control Signal CW Y Control Signal CCW Y FCTORY INSTLLED OPTIONS Violet Orange S Switch Common Q lack S Switch N.C. Q lack S Switch N.O. Q4 lack Switch Common Q lack S5 Switch N.C. Q lack S6 Switch N.C. Q4 lack Wiring Continued DCM4-44 and DCM4-88 Series 4 VC to V Modulating Control 8 9 M S S S S5 S6 S S S S5 S6 Table. Modulating Control Supply (SP) G Red Neutral (SN) G lack 8 9 to VDC Signal Y Gray Output to VDC U Pink FCTORY INSTLLED OPTIONS Switch Com Q lack Switch N.C. Q lack Switch N.O. Q4 lack Switch Com Q lack Switch N.C. Q lack Switch N.O. Q4 lack DC-44/88 Installation Instructions Page 4 of 5

5 Dual In-Line Package (DIP Switches) Raise the protective cover from the left to right to locate the DIP switches. MECHNICL RNGE STOP DIRECTION OF ROTTION SWITCH The Factory Setting is (OFF). When using the mechanical range stop to limit the angle of rotation, turn the self-adapting switch ON so that the adjusted range will become the new to % for the actuator logic. In this case, to % is not equal to. When the self-adapt feature is ON, it will automatically check the range after the voltage failure, or after the switch has been turned off and on with operating voltage supplied. The Factory Setting is Clockwise. The direction of rotation switch should match the damper rotation movement. OUTPUT SIGNL SWITCH The Factory Setting is Direct cting. s the clockwise angle of rotation increases, the output voltage increases. If the direction of rotation is CCW, the output signal switch should be set at reverse acting to match the direction of the rotation switch. Dimensions 7/6 () min 4 in. mm / (.8) ( ) / () 5/ () 5 7/6 (7) min in. 6mm min in. mm 7/6 (87) (5 7/6) /8 (68) 7-/6 (8) 5/6 (94) /8 (6) min. in. 6mm 5/ (4) /6 () /4 (7) Figure. Dimensions of the Delta DC-44 and DC-88 Series ctuator and Mounting racket. DC-44/88 Installation Instructions Page 5 of 5