BMW 745Li E65/E66 Rear Brake Pad Replacement By Jerry Incollingo (Jerry 745Li)
|
|
- Russell Gardner
- 5 years ago
- Views:
Transcription
1 Page 1 of 11 BMW 745Li E65/E66 Rear Brake Pad Replacement By Jerry Incollingo (Jerry 745Li) This guide will detail how to change the rear brakes on late model BMW E65 / E66 s. It was performed on a Li and should be similar for all models from 2002 to The approximate time to complete this project is one to two hours, based on your experience changing brakes. You will need the following: Wheel Chocks Jacks Stand 7mm 3/8 driver or #17 3/8 Torx driver 3/8 Socket Wrench Channel Locks Brake Grease / Anti Squeal Lubricant Brake Pads Brake Wear Sensor (needed if your idrive is telling to change the brakes) C-Clamp Figure 1
2 Page 2 of 11 Important: Safety First! You can be injured or even killed if the vehicle ends up on top of you. Do not rely solely on the jack to hold the vehicle in place while performing maintenance. You should wear eye protection as well. (I m the guy who get s picked on by the neighbors for wearing ear protection while cutting my lawn and eye protection for weed whacking). That said, let s begin: 1. Start by parking the vehicle on a flat, level surface. 2. Place your wheel chocks under each of the front tires 3. Loosen the wheel bolts on passenger back wheel using the tire iron included with the vehicle. It is located in the trunk, under the carper on the left side. Use care when loosening the bolts as you can scratch or ding the rim 4. Using the BMW jack raise the vehicle enough to remove the wheel. The jack is located in the trunk, on the right side below the fuse compartment 5. Using a jack stand as a supplement to the jack, place it under the cross brace near the rear of the vehicle. Because I could not fit mine under I used two 4x4 blocks of wood and located them near the jack. If someone knows the proper location to support the vehicle once lifted please let me know so I can update this documentation. Important: Stuck Wheels Many people have reported stuck wheels after removing the wheel bolts. This is usually due to corrosion around the center hub of the rotor where it meets the rim. I have found the best method to remove the stuck wheel is to remove the wheel bolts, jack up the vehicle, squirt WD- 40 into the lug holes and let it soak. Then, using a sledge hammer, gently hit the tire, not the rim, from the inside underneath the vehicle (See Figure 2). You should be able to move the rim outward a bit. Then, push it back from the other side and hit it with the sledge hammer again. Continue to do this until the wheel is free. Figure 2 6. With the wheel removed from the vehicle inspect the rotor. If there are any grooves in the rotor or the lining seems too thin you should replace them as well. I will not detail rotor replacement in this guide. See the guide on Front Brake Replacement for details
3 Page 3 of 11 on rotor replacement in the bimmerfest.com DIY section for the E65/ Remove the two dust caps from the caliper pins (See Figure 1) 8. Remove the guiding bolts by using your 7mm 3/8 hex driver (See Figure 1) a. If the 7mm Hex driver does not fit use a #17 3/8 Torx driver 9. Remove the brake pad clip by squeezing inward with your channel locks. The clip will pop out as you squeeze it (See Figure 3) Figure Remove the wear sensor from the inside brake pad by pulling it outward. It is very easy to break the plastic sensor, so if you are not replacing the sensor use extra care when removing it. The sensor is located on the passenger side only. (See Figure 4)
4 Page 4 of 11 Figure Remove the sensor by disconnecting it at the junction holder. First, gently pull the entire white connector out of the junction box. There is a plastic tab that you push in while pulling out to separate the socket housing. (See Figure 5) 12. Don t remove the whole sensor at once, rather, start at the socket housing and remove the old sensor connector first. Plug in the new sensor connector and follow the wire from the old sensor and replace it with the new sensor wire as you go. This way you won t have to remember how the wire was routed if you had removed it all at once 13. Once you have completely routed the new sensor wire tuck it out of the way until you are ready to connect it back into the brake pad
5 Page 5 of 11 Figure You may now remove the caliper and old pads. Most likely the caliper will be too tight to remove easily. If this is the case place you C-clamp around the caliper with one part of the C-Clamp on the back of the outside brake pad and the other part on the rear of the caliper itself. (See Figure 6) Tighten the clamp slightly and you will see the pad begin too loosen. Now pull the caliper away and remove the old pads. Note the orientation of the pads so you can put the new pads in correctly 15. Rest the caliper on the top of the front axel while you prepare the new pads. Take care to ensure it does not fall off. You may want to use a metal coat hanger to secure it to the axel (See Figure 7)
6 Page 6 of 11 Figure 6
7 Page 7 of 11 Figure Apply the disk brake grease to the back of the pads using a Q-tip or your finger (See Figure 8) 17. Also apply a small amount of grease to the two guiding bolts. As the brakes wear down the whole caliper slides along the guiding bolts, so keeping them lubricated is important
8 Page 8 of 11 Figure Using your C-clamp, push the round piston in the caliper back as far as it will go by pacing the threaded part of the C-clamp into the piston and the back of the C-clamp on the caliper. (See Figure 9) Slowly tighten the C-clamp to push the piston back. Take care not to pinch or damage the brake line. Some people remove the master cylinder cap in the engine compartment to before moving the pistons; however, I found this was not necessary
9 Page 9 of 11 Figure Once the piston is pushed back insert the brake pads into the caliper 20. Replace the caliper over the rotor 21. Replace and tighten the two guiding bolts 22. Replace the dust caps 23. Replace the clip by tilting it inward and pushing it back in place. (See Figure 10) 24. Take this opportunity to clean the rim inside and out before replacing it on the vehicle 25. Repeat these steps for the drivers side 26. Start the vehicle and depress the brake pedal several times to restore pressure to the rear brakes 27. Take it for a drive and listen for any squealing or any other problems 28. Reset the idrive rear brake counter by doing the following: (borrowed from E65/66 Front Bake Replacement & Computer Reset, thanks to paulmurphyhomes on bimmerfest.com) a. Start the vehicle
10 Page 10 of 11 b. Press and hold the trip meter button until a menu lights up in the speedometer display c. Press the trip meter button to scroll to "Rr. Brake" d. Press and hold trip meter button until a menu lights up in the tachometer display e. Press the trip meter button to scroll down to "RESET Rr. brake" in the menu in the tachometer display f. Press and hold the trip meter button. g. Remove the key and your computer should be reset Figure 10
11 Page 11 of 11 Clean those rims!
Installing Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More informationHawk Brake Pads ( Mustang GT/V6 Rear Pair)
Hawk Brake Pads (1994-2004 Mustang GT/V6 Rear Pair) The below installation instructions work for the following products: Hawk HPS Brake Pads (1994-2004 Mustang GT/V6 Rear Pair) Hawk Performance Ceramic
More informationHow to Change Front Brake Pads on a Toyota Corolla
How to Change Front Brake Pads on a Toyota Corolla Link to this article on (All other links in this document are disabled) Follow this picture guide to change the front brake pads on a 2003-2008 Toyota
More informationThe following information shows the steps to change the rear brake pads and rotors on an E36 chassis.
1 of 20 1/18/2010 9:15 PM See More DIY Articles Bookmark Site! The following information shows the steps to change the rear brake pads and rotors on an E36 chassis. Disclaimer: The following information
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationLowering Spring Installation on a Mustang GT
Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a
More informationNEW BRAKE INSTALLATION. Let us show you how a
Tech Article From Newsletter 17.2-2nd Quarter of 2011 NEW BRAKE INSTALLATION Let us show you how a Big Brake Install is easier than you think!! So, you have a 572 (or a hot 383) in your shoebox... you
More informationHow to install Front Brake Pads on your GT, V6
Time Necessary: Approximately 1.5 hours Tools Required: How to install Front Brake Pads on your 99-04 GT, V6 Jack Jack stands Torque wrench Ratchet Lug wrench 15mm socket 12mm socket Large C-clamp Syringe
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationThis document provides instructions for removing and installing a Front Wheel / Rotor on a Ducati Superbike. The torque values used are for the 748/916/996 from 1994 to 2001 and may be applicable for later
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More informationFORD COBRA JET SPRING INSTALLATION
FORD COBRA JET SPRING INSTALLATION Tools Needed: 1. Floor jack with rubber padding on lift point or vehicle lift 2. Jack stands (2) 3. Socket sizes 13/16, 3/4, 15mm, 8mm 4. Pliers 5. Breaker bar, ratchet
More informationServicing front brakes
46-1 Servicing front brakes C54 brake caliper, servicing Special tools and workshop equipment required VAG 1331 Torque wrench (or equivalent) VAG 1410 Torque wrench (or equivalent) VAG 1869/2 Brake pedal
More informationLand Rover Discovery 3. Bodsy s Brake Bible. Ian Bodsworth Disco3Club.co.uk June 2010 Version 1.2a
Land Rover Discovery 3 Bodsy s Brake Bible Ian Bodsworth Disco3Club.co.uk June 2010 Version 1.2a Change Record DATE Revision Update Notes Made By May 2010 1.2 Amended Torque Figures and bolt Ian Bodsworth
More informationFord Focus Front Brake Pad Replacement
2005-2007 Ford Focus Front Brake Pad Replacement Replacing the brake pads on all 2005-2007 Focus models with rear drum brakes. Written By: David Hodson ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION
More informationM-Force E36 Camber Plate Installation
Thank you for purchasing the Adjustable Camber Plate kit from Vorshlag Motorsports. In order to ensure proper installation and longevity of your kit, Vorshlag Motorsports recommends that you have your
More informationALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1)
ALLOY USA AXLE INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack Stands
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2005 2010 DROPPED SPINDLE DATSUN 720 2 WHEEL DRIVE PICK-UPS NISSAN HARDBODY 2WD PICK-UPS Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent
More informationInstallation Instructions for BMR Lowering Springs Performance ( Mustang GT)
Installation Instructions for BMR Lowering Springs Performance (2015-2017 Mustang GT) Time Required: 3+ hours Notes: This install was done with the performance springs from BMR, but install should be the
More informationBarton Short Throw Shifter 11/12 V6, GT Mustang:
Barton Short Throw Shifter 11/12 V6, GT Mustang: Tools Required: 10mm deep socket Socket wrench 10 extension for socket wrench Jack Jack stand Small piece of wood Small hook tool (recommended) *can be
More informationDodge Caravan Brake Pads and Rotors Replacement
2001-2007 Dodge Caravan Brake Pads and Rotors Replacement Written By: aelegg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide shows how easy it is for someone with little skills to
More informationSpecial tools required:
34 11 000 Removing and installing/replacing brake linings on both front disk brakes Special tools required: 34 1 080 34 6 320 Necessary preliminary tasks: Remove wheels. Observe safety instructions on
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you
More informationOVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf. This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same.
OVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same. Badly corroded calipers (caused by moisture in the
More informationThis chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models.
KYMCO MXU 500i/700i Repair Manual Brake System 9.Brake System This chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models. 1.Brake Discs... 9-3
More information1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4" fittings
1986 Rear Disk Brake Upgrade Being well prepared for a project of this size is the key to success. I thought I was well prepared by doing a lot of research and getting all of the required parts before
More informationSteeda Lower Control Arms ( )
Steeda Lower Control Arms (2005-2012) NOTE: The following installation was performed on a 2007 Mustang GT/California Special. The control arms were previously sold in a blue color, but now they are sold
More informationVolkswagen Passat Driveshaft Removal (B5 TDi)
Volkswagen Passat Driveshaft Removal (B5 TDi) About this guide This document is intended as an amateur maintenance guide to assist you with removal of the driveshaft in your VW Passat. The removal procedure
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationLMB-C6 CF Senior Member
LMB-C6 CF Senior Member Rotor install DIY... ****** FRONT: ****** Remove the wheel. To remove the rotor you need to remove the caliper and the bracket. There are 2 bolts for the caliper (top smaller bolt
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationFull Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra)
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra) Tools Required: Jack and jack stands (Or a lift) Metric sockets 8,12,15,18,21mm and a 12pt 12mm socket for driveshaft bolts T40 torx bit
More informationSaab 9-3 CV M04-, 4D/5D M06-
SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part
More information12. FRONT WHEEL/FRONT BRAKE/
12 4.5kgm 0.9kg-m 4.5kg-m 12-0 SERVICE INFORMATION... 12-1 HYDRAULIC BRAKE... 12-10 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-16 FRONT WHEEL... 12-3 STEERING HANDLEBAR... 12-19 FRONT BRAKE...
More informationSteeda Bumpsteer Kit (94-04) - Installation Instructions
Steeda Bumpsteer Kit (94-04) - Installation Instructions The below installation instructions work for the following products: Steeda Bumpsteer Kit (94-04) Please read through the instructions carefully
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive
More informationEGR Performance Brakes Assembly Instructions DODGE DANA 70 '87 - '93 (Will not fit stock sized dual rear wheels)
EGR Performance Brakes Assembly Instructions DODGE DANA 70 '87 - '93 (Will not fit stock sized dual rear wheels) Got Brakes? Parts List (2) Vented Rotors (2) Multi hole Cable Mount & L Brkt (2) Axle Tube
More informationPart Numbers: Complete Kits: C5 Base/Z06 Complete Header Package with Cats C5 Base/Z06 Complete Header Package without Cats
Product: Corvette Tri-Y Headers & Mid-Pipe Part Numbers: Complete Kits: 1150042 C5 Base/Z06 Complete Header Package with Cats 1150043 C5 Base/Z06 Complete Header Package without Cats Applications: Chevrolet
More informationInstallation Guide: Front Brake Pad
Installation Guide: Front Brake Pad Ninety percent of the brake pad changes you make during the life of your vehicle will be to the front brakes because they do 60% to 70% of the braking. On most cars,
More informationSUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm. Acrobat Printable Version
SUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm Introduction Acrobat Printable Version I'd like to thank Ben Davis for providing the pictures for this procedure. Ben took the time to take
More informationE31 Repair Procedure Replace Front Wheel Hub/Bearing Assembly
E31 Repair Procedure 31-21 Replace Front Wheel Hub/Bearing Assembly Disclaimer This repair procedure is provided as is and is not authoritative with respect to any BMW repair operation. Mark F. Fling is
More informationHow To: Replace Brembo front discs & pads
How To: Replace Brembo front discs & pads Necessary Tools required Good quality socket set. T55 Torx/spline bit of very good quality. T30 Torx/spline bit. T27 Torx /spline bit WD40 Mallet. Punch. Brake
More informationKG09100BK / KG09101BK GM WD.
KG09100BK / KG09101BK GM. 1988-2006 2 WD. KG09101BK KG09100BK Instruction Sheet: P10476-05 2013 Daystar Products International Inc. Tools Needed Quantity Description 1 Floor Jack 2 Jack Stands 2 Wheel
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2100 DROPPED FRONT SPINDLE CHEVROLET 2WD S-10 / S-15 PICKUP / BLAZER / JIMMY, including models with ABS General Motors G-Body Rear Wheel Drive Cars CONGRATULATIONS! You were selective
More informationDisco 3 Clock Spring / Rotary Coupler replacement
Disco 3 Clock Spring / Rotary Coupler replacement I recently had to change my Clock spring and thought some folks may find it helpful to see what it entailed. I did lots of reading around but couldn t
More informationPowerslot Mustang Rotors (Rear Pair GT/V6) - Installation Instructions
Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) - Installation Instructions The below installation instructions work for the following products: Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) Please
More informationInstallation Instructions for disc brakes
Installation Instructions for disc brakes Bedford CF 230-280, built 1974-1986, not suitable for vehicles with rear twin tyres Included 2 pcs. Wheel Hubs with Wheel Bolts, Mounted Brake Discs and Wheel
More informationRelease the electrical wire from the bracket -2- toward the left -A- and remove.
Page 1 of 8 Front Brake Pads, FBC-60, Removing and Installing Always replace on both axles. Special tools and workshop equipment required t Torque Wrench 5 50 Nm -V.A.G 1331- t Reversible Ratchet -V.A.G.
More informationReplace brake pads and discs - rear * (Volkswagen Golf )
Replace brake pads and discs - rear * (Volkswagen Golf 1997-2004) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2000 1984 1991 Toyota 2 Wheel Drive Pick-Ups 2 Front Dropped Spindles Congratulations!
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION REAR KIT SUM-BK1423 1999-2009 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time to read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767 3100-3200 3 DROPPED FRONT SPINDLE 73-87 1/2 TON C-10 PICK-UP / 1/2 TON BLAZER
More informationPerformance Brake Caliper Guide Bushing Set Installation Guide
Performance Brake Caliper Guide Bushing Set Installation Guide Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those
More informationHow to change front brake pads, and rotors and bleed brakes on a 98 VW Jetta GLS (Other models, like BMW, and Audi are similar)
How to change front brake pads, and rotors and bleed brakes on a 98 VW Jetta GLS (Other models, like BMW, and Audi are similar) This "how to" assumes you have some basic tools, and safety gear. Safety
More informationBMW E61 Hydraulic Pump replacement instructions
BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part
More informationBADEN'S BMW DIY #7 E46 Shock and Strut Replacement
- Baden's Car Pages web site - http://www.badenscarpages.ca - DIY #7 E46 Shock and Strut Replacement Posted By Baden On February 15, 2010 @ 1:38 PM In E46 39 Comments BADEN'S BMW DIY #7 E46 Shock and Strut
More informationMaintenance Information
Form 04584058 Edition 1 November 2004 Air Impactool 2141P and 2141PSP Maintenance Information Save These Instructions Disassembly General Instructions 1. Do not disassemble the tool any further than necessary
More informationCBEA/CJAA Timing belt procedure. Written by: greengeeker Photos by: DanG144, Kriesel, coalminer16. Required tools:
CBEA/CJAA Timing belt procedure Written by: greengeeker Photos by: DanG144, Kriesel, coalminer16 Required tools: 1. Securing pin 3359 (you need two of them!) 2. Crankshaft stop T10050 3. Counter-hold tool
More informationBrake master cylinder replacement
Brake master cylinder replacement 8-25-2010 I had replaced the front brake master cylinder a few years ago when it developed a bad leak, at that time, I ordered a new master cylinder from Spartan, very
More informationDISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:
Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationR-SE JK 4 DOOR Step Slider Install Instructions. *If any parts listed are missing or damages please call prior to install.
R-SE JK 4 DOOR Step Slider Install Instructions Parts List: 1 Divers side slider assembly 1 Passenger side slider assembly 1 wiring harness 1 control box 2 spacers 2 LED lights (optional) 10 SS Button
More informationDBK FULL-SIZE CHEVY DISC BRAKE conversion KIT
DBK5964 1959-1964 FULL-SIZE CHEVY DISC BRAKE conversion KIT impala, bel air, biscayne Installation Instructions does not fit 14" rims must ust 15" or larger for this kit to be installed correctly on your
More informationWARNING: Only perform this installation if you are experienced, fully equipped mechanic.
DYNATRAC V3.2 2005-Present Ford Super Duty 250/350-4x4, Front Axle, Free Spin Conversion Kit Some of the less common tools, which will be required: 6 point Spanner socket (OTC #7090-A or equivalent). These
More informationHawk HP Performance Brake Pads (94-98 GT/V6 Front Pair) - Installation Instructions
Hawk HP Performance Brake Pads (94-98 GT/V6 Front Pair) - Installation Instructions The below installation instructions work for the following products: Hawk HP Plus Performance Brake Pads (94-98 GT/V6
More information12. FRONT WHEEL/FRONT BRAKE/
12 12 12-0 SERVICE INFORMATION... 12-1 FRONT BRAKE... 12-7 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-18 STEERING HANDLEBAR... 12-3 FRONT FORK... 12-21 FRONT WHEEL... 12-4 SERVICE INFORMATION GENERAL
More informationMaximum Motorsports Camber Caster Plates (05-10):
Maximum Motorsports Camber Caster Plates (05-10): Tools Required: Lug Wrench 21mm Deep Socket 18mm Deep Socket 15mm Deep Socket 17mm Socket 13mm Socket 10mm Socket Torque Wrench (requires 166lb-ft capacity
More informationFORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1)
FORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack
More informationFord Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions
Ford Racing Front Rotor Upgrade Kit (05-10 V6) Installation Instructions Time Necessary: Approximately 1.5 hours Tools Required: 15 MM Socket Ratchet PryBar Floor Lift or: o Floor Jack o (2) Jack Stands
More information2003 Jaguar X-Type BRAKES' 'Disc - X-Type
REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.
More informationAmTryke Adult Recumbent Model JT2000 #50-FC-2000
AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC2001, RC2001X Applications: Mopar 8-3/4 & 9-3/4 Rear Axles Thank you for choosing Leed Brakes for your automotive product needs. Before
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION KITS A126-67 2002-11 GM 2500/3500 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationTOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation
TOYOTA TUNDRA 2007- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-34070 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake
More informationSUM Chevy Truck frame mount booster kit
SUM-760211 1955-1959 Chevy Truck frame mount booster kit Unboxing your kit: 1. Remove new booster, bracket assembly and master cylinder from their boxes and inspect the parts. 2. New boosters come with
More informationChange Your Tail Wheel Bearings (and Races)
Change Your Tail Wheel Bearings (and Races) Note: You must have the approval of a certified aircraft mechanic (A&P) to perform this procedure. This procedure worked with my tail wheel but yours may differ.
More informationGM FULL SIZE REAR DISC BRAKE KIT
GM FULL SIZE REAR DISC BRAKE KIT This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left). If your axle flange measures 3 1/8 from center to center, you need
More informationPIKE DUAL AIR PICTORIAL INSTRUCTIONS. INSTRUCTIONS FOR INSTALLING ENDURO FORK SEALS AND CHANGING SEMI-BATH OIL in RockShox PIKE Dual Air Forks
INSTRUCTIONS FOR INSTALLING ENDURO FORK SEALS AND CHANGING SEMI-BATH OIL in RockShox PIKE Dual Air Forks RECOMMENDED PARTS AND TOOLS -Bicycle work stand -Plastic bucket/drain pan -5mm Allen wrench -DH
More information1464. Interior Installation. Cover Rear Seat Support Cut the vinyl to approximately the size of the rear seat support.
Chapter 37 (Video Clip 37) - Interior Installation 1464. Interior Installation Cover Rear Seat Support 1465. Cut the vinyl to approximately the size of the rear seat support. 1466. Make a dry fit of the
More informationFitting Instructions. Revo MQB Golf/GTi/Octavia/Leon Intercooler. Recommended Tools. Contents RV581M Dealer installation advised.
RV581M100100 Recommended Tools Contents No. Description Tools Size Intercooler Torx Bit T25, T30 Bracket Kit llen Key 4, 5 mm Silicone Hoses Socket 7, 10, 16, 19 mm Hose Clamps Flat Head Screwdriver Small,
More informationBrake Caliper Rebuild - Part Numbers & Tips Per Jim Millet, 3/15/2005
Per Jim Millet, 3/15/2005 Not too difficult a job. Rears are easier than fronts to access. You ll need the following gasket sets: Front caliper gasket set, P/N 34 11 1 157 037, MSRP $13.58 Rear caliper
More information2015+ HELLCAT 6.2L HEMI System vehicle specific plate system xx
These installation instructions will guide you through installing the Nitrous Outlet 2015+ Hellcat 6.2L Hemi Vehicle Specific Plate System on your vehicle. Before you get started, remember to never use
More informationFord C4 and C6 Floor Mount Automatic Transmission Shifter Installation Instructions
Ford C4 and C6 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C4 and C6 Mount
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COMP. R AND COMP. S QUICK CHANGE KITS A200, A200-1 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully
More informationTOYOTA COROLLA LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description
More information02-10 GM 2500HD / HD & HD CLASSIC 6 2WD SUSPENSION KIT
92122000 92127400 02-10 GM 2500HD / 01-06 1500HD & 07 1500HD CLASSIC 6 2WD SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician
More informationkit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions
InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950
More informationCBEA/CJAA Timing belt procedure. Written by: greengeeker Photos by: DanG144, Kriesel, coalminer16. Required tools:
CBEA/CJAA Timing belt procedure Written by: greengeeker Photos by: DanG144, Kriesel, coalminer16 Required tools: Securing pin 3359 (need two of them!) Crankshaft stop T10050 Counter-hold tool T10172 Special
More informationBMW 3 SeriesE90 - E93 Factory Alarm Install
Instructions on a BMW 3 Series Factory Alarm Install. Written By: Danielle 2017 guides.drivediy.com Page 1 of 9 INTRODUCTION Tips on how to install a BMW 3 Series Factory alarm. Credit: CC 330i[E90Post.com
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More informationTools, Equipment and Supplies Needed:
153-162 DISC BRAKE/DUAL MASTER CYLINDER CONVERSION Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarifi cation.
More information