General Manager/Service Manager/Warranty Administrator. 2015FL-005 Attachment #2 1KD Diesel Turbo Replacement Campaign Repair Instructions
|
|
- Randolf Austin
- 5 years ago
- Views:
Transcription
1 Toyota Material Handling, U.S.A., Inc Inwood Drive (47201) P.O. Box 3009 Columbus, IN Date: September 4, 2015 To: From: Subject: General Manager/Service Manager/Warranty Administrator Gene Babinec III Warranty Administration Manager 2015FL-005 Attachment #2 1KD Diesel Turbo Replacement Campaign Repair Instructions Work Outline Toyota requests the replacement of the 1KD Diesel Turbo sub-assembly on select 2014/2015 Toyota forklift models 8FD35U-80U. Parts required: There is a kit available from TIEM service parts. Model 8FD35U-80U o Require kit: U (contains all parts required to complete Turbo Sub-assembly replacement) Parts return: The removed parts are not required for warranty parts return. Please destroy parts and recycle accordingly. Page 1 of 8
2 1. Work outline Replacement procedure for Turbo Charger Sub-assembly Replace the Turbo Charger S/A with new one Fig. 1 Engine room Fig. 2 Turbo Charger S/A 2. Parts to use - All parts included in Turbo Campaign Kit Part number: U , do not order individually. No Fig. Qty/ Part name Part number No. unit Remark 1 A TURBO CHARGER SUB-ASSY UL B BOLT, STUD For Inlet elbow pipe 3 C GASKET UL010 1 For Inlet elbow pipe 4 D GASKET For Water pipe 5 E GASKET, OIL INLET For Oil pipe 6 F BOLT, STUD For Turbo Stay 7 G NUT For Turbo Stay 8 H GASKET TURBO TO EXHAUST For Turbo - Exhaust Manifold 9 I NUT For Turbo - Exhaust Manifold 10 J GASKET, EXHAUST MANIFOLD, For Exhaust Manifold NO K NUT, LOCK For Exhaust Manifold 12 L GASKET, OIL OUTLET For Oil pipe 13 M GASKET For Oil pipe 14 N GASKET UL010 1 For Converter 15 O NUT For Converter 16 P GASKET, EXHAUST PIPE For Converter - Exhaust pipe 17 Q NUT For Converter - Exhaust pipe Please check whether the boxes include parts for 1KD by checking label Please check that "1KD" is written in the label Fig. 3 Label for identification 3. Work procedure and points Work safely according to "OPERATIONAL TIPS" in the repair manual for 8FG35U-80U series (. * CE104). * Long Life Coolant and oil remaining in the engine can be flushed during procedure. Page 2 of 8
3 Removal procedure of related parts from truck: (Fig. 4) 1) Park the truck on a level ground. 2) Set the parking brake. 3) Remove the key and keep it aside. 4) Open the engine hood and disconnect the battery negative terminal, remove the batteries and tray. 5) Remove the floor mat and the rear toe board. 6) Remove the radiator cover 7) Remove the relay block and injector driver 8) Drain coolant Fig. 4 Relay block and Injector driver Removal procedure of Turbo charger S/A from engine 9) Remove "1: Converter separator insulator No.1" 10) Remove "2: Intercooler hose No.1" and "3: Pipe" (Fig. 5) 11) Remove LH engine harness from the clamp and disconnect the connectors from sensor motor. (Fig. 6) Fig. 5 "2: Inter cooler hose No.1" Fig. 6 LH engine harness 12) Loosen the clamp on "4. Air hose", "5: Air hose No.2" and "6: Ventilation hose". (Fig. 7) 13) Remove bolts between "7: Intake pipe Assy" and "8: Manifold stay No.2". 14) Remove "5: Air hose No.2", "6: Ventilation hose" and "7: Intake pipe Assy". (Fig. 8) - Clamp to be unfixed - Bolt to be removed 7: Intake pipe Assy Fig. 7 "4: Air hose" Fig. 8 After removal of "7: Intake pipe Assy" and related parts Page 3 of 8
4 15) Remove "8: Manifold stay No.2". (Fig. 8) 16) Remove "9: Exhaust manifold heat insulator No.2" and "10: Turbo insulator". 17) Remove "11: Monolithic converter ASSY". 18) Remove rear clamps of turbo water hose and plug/cap as shown to minimize coolant loss. "12: Turbo water hose No.1" (Quantity 2) (Fig. 9) 19) Remove front bolt for "13: Turbo oil inlet pipe S/A" (13-A: Bolt) (Fig. 10) 12: Turbo water hose No.1 Fig. 9 "12: Turbo water hose No.1" Fig. 10 "13: Turbo oil inlet pipe S/A" 20) From beneath the truck, remove lower bolts for "13: Turbo oil inlet pipe S/A" (13-B: Bolt) (Quantity 2) and "14: Turbo charger stay". (Quantity 2) (Fig. 11) 21) Remove nuts connecting "15: Exhaust manifold "with "16: Turbo charger S/A", (Quantity 8) and remove "15. Exhaust manifold" with "16: Turbo Charger S/A" as shown. You may have to remove rear 4 manifold studs to clear weldment on some frames. (Fig. 12, 13) Fig. 11 "13: Turbo oil inlet pipe S/A" and "14: Turbo charger stay" Fig. 12 "15: Exhaust manifold" and "16: Turbo charger S/A" Fig. 13 "16: Turbo charger S/A" with manifold as shown Page 4 of 8
5 22) Remove "15.Exhaust manifold", "17: Compressor inlet elbow", "13: Turbo oil inlet pipe S/A", "18: Turbo water pipe S/A", and "14: Turbo charger stay" from "16: Turbo charger S/A " Installation procedure of turbo charger S/A components from Kit Part Number: U ) Install new Stud bolts (B: ) at (T=5-8ft. lbs) and new Gasket (C: UL010). 24) Install "17: Compressor inlet elbow" on new "16: Turbo charger S/A (A: UL010)" (T=10-18ft. lbs). 25) Install new Gasket (D: ) and "18: Turbo water pipe S/A" (T=6-11 ft. lbs) on new "16: Turbo charger S/A (A: UL010)". 26) Install new Oil inlet gasket (E: ) in accordance with Fig ) Install "13: Turbo oil inlet pipe" on new "16: Turbo charger S/A (A: UL010)" by hand starting "13-B: Bolt" (Quantity 2). Install this side into "16: Turbo charger S/A" Fig. 14 Stud bolt (B: ) installing direction Fig. 15 Oil inlet gasket (E: ) installing direction 28) Install new Stud bolt (F: ) (T=10-18ft. lbs) on the new "16: Turbo charger S/A (A: UL010)". (Fig. 16) 29) Add new nut (G: ) to (F: Stud bolt) that will attach "14: Turbo charger stay" to the "16: Turbo charger S/A (A: UL010)" hand starting. 30) Install new "Gasket Turbo to Exhaust (H: )" on "16: Turbo charger S/A" 31) Install "16: Turbo charger S/A" on "15: Exhaust manifold" by hand starting new Nuts (I: ). Install water pipe to turbo housing. 32) Install "16: Turbo charger S/A" on Engine Assy with "EXHAUST MANIFOLD, NO.1 Gasket (J: ) by hand starting Lock Nut (K: ). Note: Be careful not to damage the assembly during installation. 33) Tighten "15. Exhaust manifold" fully in accordance with the order in Fig. 17. (T=23-35ft. lbs) Fig. 16 Stud bolt (F: ) installing direction Fig. 17 "15. Manifold Exhaust" tightening order Page 5 of 8
6 34) From the beneath of the truck, install "14: Turbo charger stay" by hand starting lower bolts. (Fig. 18) 35) From the beneath of the truck, install new Oil outlet gasket (L: ), (Fig.18, 19) and "13: Turbo oil inlet pipe S/A" by tightening the lower bolts (13-B: Bolt) by hand starting. Fig. 18 "13: Turbo oil inlet pipe S/A" and "14: Turbo charger stay" Fig. 19 Oil outlet gasket (L: ) installing direction 36) Install new Gasket (M: ), and hand start the front bolt for 13: Turbo oil inlet pipe S/A (13-A: Bolt). (Fig. 20) 37) Tighten the bolts which connect "15: Exhaust manifold"&"16: Turbo charger S/A" fully. (T=30-46 ft. lbs.) 38) Tighten the front bolt for "13: Turbo oil inlet pipe S/A" (13-A: Bolt) fully. (T=21-31 ft. lbs.) 39) From the beneath of truck, tighten the nut connecting "13: Turbo oil inlet pipe S/A with "16: Turbo charger S/A" fully. (T=8-11 ft. lbs.) (Fig. 21) 40) From the beneath of the truck, tighten the lower bolts for 13: Turbo oil inlet pipe S/A (13-B: Bolt) fully. (T=7-10 ft. lbs.) (Fig. 22) Fig. 20 Front bolt for "13: Turbo oil inlet pipe S/A" (13-A) Fig. 21 "13: Turbo oil inlet pipe S/A" Fig. 22 "13: Turbo oil inlet pipe S/A" Page 6 of 8
7 41) From the beneath of the truck, tighten bolts for "14: Turbo charger stay" fully.(t=23-33ft. lbs)(fig. 23) 42) Install "12: Turbo water hose No.1" and the clamp in accordance with Fig. 24. (Quantity 2) (Fig. 24) Fig. 23 "14: Turbo charger stay" Fig. 24 "12: Turbo water hose No.1" 43) Install the new Gasket (N: UL010) on the new "16: Turbo charger S/A". 44) Install "11: Monolithic converter ASSY" by hand starting upper bolts. (Fig. 25) 45) Install "11: Monolithic converter Assy" on "16: Turbo charger S/A" by the new Nuts (O: ). (T=23-34 ft. lbs.) 46) Tighten upper bolts for "11: Monolithic converter Assy" fully. (T=11-20 ft. lbs.) Install cat heat shield. 47) Install the new Exhaust pipe gasket (P: ) and connect "11: Monolithic converter Assy" with "Exhaust pipe" by new nuts (Q: ) (T=23-34 ft. lbs.) 48) Install "10: Turbo insulator" (T=11-20 ft. lbs.) 49) Install LH engine harness into the clamp, and connect connector. (Fig.26) 50) Install "9: Exhaust manifold heat insulator No.2". (T=19-28 ft. lbs.) 51) Install "8: Manifold stay No.2". (T=19-28 ft. lbs.) 52) Install "5: Air hose NO.2", "6: Ventilation hose", and "7: Intake pipe Assy". (Fig.27) Fig : Monolithic converter ASSY Fig. 26 LH engine harness Fig. 27 "7: Intake pipe ASSY" and related parts Page 7 of 8
8 53) Install clamp for "6: Ventilation hose (Fig. 28) 54) Tighten the clamp for "8: Air hose No.2" (T= 1-4 ft. lbs.) (Fig. 29) Fig. 28 "6: Ventilation hose" Fig. 29 "5: Air hose No.2" 55) Tighten the clamp between "7: Intake pipe Assy" and "4: Air hose". (Fig.30) 56) Install "2: Intercooler hose No.1" and "3: Pipe". (Fig.31) 57) Install "1: Converter separator insulator No.1". 58) Fill coolant, and check engine oil level. 59) Install the relay block and the injector driver. 60) Install the floor mat and the rear toe board. 61) Install the battery and the battery tray. 62) Install the radiator cover 63) After completing all the repair work, make sure that the truck functions normally, check engine oil and coolant levels. Page 8 of 8
ENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More informationInstallation Instructions
2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com
More informationREMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
More informationENGINE ACCESSORIES. D20DT Engine. PCV valve and oil separator. Turbo charger. EGR pipe (LH, Center, RH) Cooling fan clutch. Auto tensioner.
01 41 ENGINE ACCESSORIES Engine GENERAL PCV valve and oil separator Turbo charger Power steering pump Fuel return hose Alternator EGR pipe (LH, Center, RH) Cooling fan clutch EGR valve Auto tensioner Cable
More informationSection 7.3 Water Manifold has been updated.
NUMBER: 08 DD15-11 S.M. REF.: 7.3 ENGINE: DD15 DATE: September 2008 SUBJECT: WATER MANIFOLD PUBLICATION: DDC-SVC-MAN-0002 Section 7.3 Water Manifold has been updated. 7.3 WATER MANIFOLD Coolant flows from
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009
NUMBER: 8 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationSupplement to Yanmar Kit Installation Instructions SAFETY
Supplement to Yanmar Kit Installation Instructions SAFETY This product is designed and intended only for use with a YANMAR engine. All safety and warning information contained in the Yanmar Operation Manual
More informationPARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More informationPARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More information6.4L EGR Delete With Intake Elbow
6.4L EGR Delete With Intake Elbow J I E C B F D G H A Part# A B C D E F G H I J PACKING LIST: QTY. 2 4 2 4 2 Description Exhaust Block-Off Plate Exhaust Gasket Coolant Line Plugs Brass Barbed Hose Connector
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More information2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
More informationCOMPONENTS ILLUSTRATION
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (a) Remove the windshield wiper motor and link assembly. 2. REMOVE COWL BODY MOUNTING REINFORCEMENT
More information4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions
4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions
More informationEM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL
92 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE ( FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for Pre Runner and 4WD Type) (a) Remove the
More informationREMOVAL AND INSTALLATION
303-08-1 Engine Emission Control 303-08-1 REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Cooler 6.4L Diesel, Vertical Cooler Item Part Number Description 1 Fuel cooler tube 2 W701317 Power steering
More informationSTARTER COMPONENTS FOR REMOVAL AND INSTALLATION
Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationEM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side
112 Intake Air Surge Tank Side Cylinder Head Side 1GR-FE ENGINE MECHANICAL ENGINE ASSBLY INSPECTION 1. INSPECT INTAKE MANIFOLD FOR WARPAGE (a) Using a precision straight edge and feeler gauge, measure
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More informationCHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More informationBD TrackMaster S D o d g e H P C R Installation Instructions
7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge
More informationV8 XJ Series/XK. Remove and destroy Bulletin , dated 02/02. Replace with this Bulletin. Revisions are marked with a bar and in bold text.
SERVICE V8 XJ Series/XK DATE 02/02 amended 05/02 TECHNICAL BULLETIN Coolant Leakage Heater Hoses Repair Procedure MODEL 303-48 1997-99 MY XK Range 1998-99 MY V8 XJ Series VIN 010343-042635 812256-878274
More informationPage 1 of 5 2004 Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationON-VEHICLE INSPECTION
452 DLC3 CAN VIM Intelligent Tester G035612E02 ON-VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Listen to the throttle control motor operating sounds. (1) Turn the ignition switch to ON. (2) When pressing
More informationIntake Manifold: Service and Repair Removal
1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling
More information2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION
XDP 6.0L Complete EGR Delete Kit w/up-pipe Item Number: XD169 PACKING LIST: 2 - Lined 3/4" Hose Clamps, 1-180 Coolant Tube, 1-3/4 Silicone Hose, 1 - Stainless Steel Up-pipe 1 - EGR Valve Block-Off Plate,
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More informationThis information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More informationPARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
More information1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder
ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION
More informationCLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica
CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release
More informationTURBOCHARGER ON VEHICLE INSPECTION TC 7
TC7 ONVEHICLE INSPECTION 1. INSPECT INTAKE AIR SYSTEM Check for leakage or clogging between the air cleaner and turbocharger inlet and between the turbocharger outlet and cylinder head. Clogged air cleaner...
More informationDODGE SRT-4 PART NUMBER P (with Turbo Toys) P (without Turbo Toys) P (Stage 2 to Stage 3R Upgrade Kit)
INFORMATION SHEET Stage 3R Turbo Upgrade Kit Components (1) Stage 3R PCM (4) 682 cc/min Fuel Injectors* (1) 3.0 bar MAP Sensor* (1) 3.0 bar TIP Sensor* (1) Block-off Connector for PCM (1) Mopar TD05HR
More information2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 7 SECTION 303-04F: Fuel Charging and Controls Turbocharger, 6.0L Diesel 2003 F-Super Duty 250-550/Excursion Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Turbocharger
More informationInstallation Instructions
BD DODGE CUMMINS PERFORMANCE E X H A U S T M A N I F O L D Installation Instructions Application List 2007-2015 6.7L / HE351 OE Turbo 1045965 2007-2015 6.7L / T4 S400 Turbo s 1045965-T4 PLEASE READ ALL
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationEngine. Table of Contents
Engine Table of Contents Sub-Headings Safety 2 Warnings 2 Cautions 2 Notes 2 Introduction 2 Tools Required 2 Preparatory Work 2 Hood, Bumper and Grill Removal 3 Charge Air Cooler and Radiator Removal 3
More informationEM 97 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSTALLATION
2TR-FE ENGINE MECHANICAL ENGINE ASSBLY 97 G038557E01 INSTALLATION 1. INSTALL ENGINE OIL PRESSURE SWITCH ASSBLY ( LU-1) 2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH (a) Install the engine mounting
More information18SP589* Series 60 Right Side EGR Bolt-Together System with Hydraulic Actuator Valve
18SP589* Series 60 Right Side EGR Bolt-Together System with Hydraulic Actuator Valve *Revision: 1/6/05 Introduction There are two new kits for different orientations of the hot pipe assemblies with a hydraulic
More informationPowerMax Diesel Upgrade For Cummins Engines
PowerMax Diesel Upgrade For Cummins Engines 00.5-007.5 Dodge Ram With Cummins 5.9L Item 3 4 5 6 7 8 9 0 3 4 5 6 7 8 Parts List Description Turbocharger Ancillary kit 773069- (includes) Installation Instructions
More informationDodge 24v ISB
1 BD KILLER B SINGLE TURBO KIT 1994-2002 Dodge 24v ISB Part #: 1045163 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION UNLESS AN EO# IS LISTED, THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES
More informationDURAMAX LMM EGR DELETE
007.5-010 DURAMAX LMM EGR DELETE Duramax LMM EGR Delete B K I J F D G H A C PACKING LIST: E Part # A B C D E F G H I J K QTY. 1 1 1 1 Description Billet Intake Block Off Plate with O-ring Exhaust Block
More informationOil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More informationTURBOCHARGER Toyota Celica DESCRIPTION OPERATION TURBOCHARGING SYSTEMS All Models
TURBOCHARGER 1988 Toyota Celica 1988 TURBOCHARGING SYSTEMS All Models DESCRIPTION Most models use a water-cooled turbocharger, mounted directly to the exhaust manifold with a wastegate assembly attached
More information1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
More informationINSTRUCTION BULLETIN
INSTRUCTION BULLETIN No. 9014163 Machine: M20 / M30 /T20/S30 Published: 10-2015 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More information2Charge Air Elbow, 1Install hose & Parts list. hardware kit. Clamp & O-ring. Downpipe clamp. Downpipe w/ Wrap 3 & Wrap Clamp.
Parts list 1Install hose & hardware kit 2Charge Air Elbow, Clamp & O-ring Downpipe w/ Wrap 3 & Wrap Clamp Downpipe clamp 4 4 Straight Boot 5 Exhaust manifold w/ 6 gaskets 5.9L Only 6.7L Only 4 Intake Pipe
More informationSLP Camaro ZL1 STAGE 2 (625 HP)
SLP - 2012 Camaro ZL1 STAGE 2 (625 HP) PART #26001 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More informationEXHAUST SYSTEM AND INTAKE MANIFOLD
J EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page EXHAUST SYSTEM... 1 EXHAUST SYSTEM DIAGNOSIS... 2 page SERVICE PROCEDURES... 3 TORQUE SPECIFICATIONS... 10 EXHAUST
More informationInstallation Manual v1.0: MST Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: MST Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: MST Kit Contents Figure 2: MST Hardware Kit Please make sure all of the components
More informationADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More informationDuramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationREMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.
EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER
More information2012 Mustang Workshop Manual. 14. Position the lower radiator hose assembly into the vehicle. Connect the lower radiator hose to the radiator.
14. Position the lower radiator hose assembly into the vehicle. Connect the lower radiator hose to the radiator. 15. Connect the coolant hose to the oil cooler. 16. Rotate the SC drive belt tensioner clockwise
More informationAll cores due 30 days after invoice date - no credit after 60 days.
NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.
More informationService Parts. Doosan 11.1 L. Engine. Engine Model: Generator Models: 180/200REZX 180/200RZX TP /09
Service Parts Engine Engine Model: Doosan. L Generator Models: 80/00REZX 80/00RZX TP-0 /09 Table of Contents Introduction... Numbering System Significance... Illustrations... How to Find Part Numbers...
More informationIncludes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses
Includes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More informationNOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
More information2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]
2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S] 1988 Toyota Celica 1988 TOYOTA ENGINES 2.0L & 2.0L Turbo 4-Cylinder Celica * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,
More informationPart# PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
16 November 2009 HPCR Dodge Twin Turbo Kit #1045430 1 BD Twin Turbo R700 Kit 2003-2007 Dodge HPCR ISBe Installation Instructions Part# 1045430 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. UNLESS AN
More information1998 F-150/250 Workshop Manual
Page 1 of 13 SECTION 303-01B: Engine 4.6L and 5.4L 1998 F-150/250 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 03/07/2000 Intake Manifold Removal WARNING: Do not smoke or carry lighted tobacco
More informationGHG14 DD15 Asymmetrical Turbocharger May Removal of the GHG14 DD15 Asymmetrical Turbocharger
5 31-13 1 5 31-13 SUBJECT DATE GHG14 DD15 Asymmetrical Turbocharger May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the GHG14 DD15 Asymmetrical
More informationENG-16, Turbocharger Replacement (Including Tips on K27 Turbocharger Installation)
ENG-16, Turbocharger Replacement (Including Tips on K27 Turbocharger Installation) Introduction Replacing the turbocharger on a 951 is not extremely difficult. However, it is very tedious because there
More informationAPR, LLC
+ 1. 3 3 4. 5 0 2. 5 1 8 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 + 1. 3 3 4. 5 0 2. 5 1 8 1 NOTES:
More information1999 F-150/250 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of
More informationCYLINDER HEAD (for Bank 2 4WD and Pre-Runner)
144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1
More informationEnergysaver 559FT. Rinnai New Zealand Limited Page 1 of 6 Rinnai Energysaver 559FT Spare Parts: 01-11
039 017 028 012 019 037 020 018 038 026 701 013 038 027 804 012 Top panel 1 5485 013 Control panel assembly 1 5486 016 Side panel RH 1 5488 017 Side panel LH 1 5489 018 Air filter assembly 1 3026 019 Front
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More informationScion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #
TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # 11518000 Vehicle Type Chassis Code Engine Code Transmission Model Year Scion FR-S DBA-ZN6
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationThis information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 1.2008 216 50 1(17) Sealant Crankshaft Cover, Replacement D16F Sealant Crankshaft Cover, Replacement W2005773
More informationInstallation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
More informationBD Twin Turbo Cobra Kit
14 September 2017 1045780-94 Dodge Cobra Kit (I-00377) 1 BD Twin Turbo Cobra Kit 2003-2012 Dodge HPCR Machined BD turbochargers only BUILDERS KIT Installation reccomendations to aid asssembly Does not
More informationInstallation Manual v1.0: P/N 202-A Aurora 3000/5000 Compound Turbo Kit Dodge Cummins 5.9
Installation Manual v1.0: P/N 202-A35-2272 Aurora 3000/5000 Compound Turbo Kit 2003-2007 Dodge Cummins 5.9 Please read all instructions before installation. Figure 1. Figure 2. Figure 3. Figure 4. 1. Install
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST
1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions
More informationInstallation Manual v1.1: Piece Pulse Flow Exhaust Manifold, Stock Replacement L Cummins
Installation Manual v1.1: 204-927-2326 2-Piece Pulse Flow Exhaust Manifold, Stock Replacement 2007.5-2016 6.7L Cummins Please read all instructions before installation. We suggest purchasing new gaskets
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationASSEMBLY/INSTALLATION INSTRUCTIONS
ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath
More information2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.
VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716
More information