Installation Instructions
|
|
- Eunice Hicks
- 5 years ago
- Views:
Transcription
1 Instructions Created by an: DIY Underhood LED Lighting Kit (SKU# DIY-E-UHLK) Installation Instructions NOTICE: This Under Hood Light Kit was installed on a 2002 Toyota Tacoma. However, these instructions can easily adapt to any vehicle. CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and equipment. Suggested Tools: Combination Wrenches: 12 & 11mm. Needle Nose Pliers W/Wire Cutters Phillips Screwdriver (Optional) Power Hand Drill 5/16 Drill Bit (Supplied) Abrasive Paper Wire Crimpers Wire Strippers (for 26 & 20 Gauge Wire) Heat Gun (for heating the shrink tube) 1/6 Steel Welding Rod (for fishing the conductor through body cavities) Electrician s Tape Power Probe (or 12V Test Light) For additional copies of these and other instructions go to: and click on the Instructions tab.
2 Wiring Diagram LED Light Bar Butt Connectors 26 gauge Conductors 20 gauge Conductors Fuse Block 1A + - Battery Female Spade Connector Hood Switch
3 Step 1 Insert the supplied (20 GWA) back and red wire through the hood cavity as shown. Step 2 Continue feeding the wire into the cavity until it becomes visible at the rear of the hood. Step 3 Pull the wire out of the hood cavity using needle nose pliers. Tech Tip 3 Wire pulled out of the hood cavity.
4 Step 4 Fish a piece of wire (welding rod, coat hanger, etc) through the hood cavity as shown. Step 5 Have the fish wire extend out of the hood cavity about 4 as shown. Step 6 Connect the black and red wire to the fish wire using electricians tape. Step 7 Pull the black and red wire through the body cavity as shown. Note: Keep the connection as small as possible, yet strong enough to be pulled the wire through the hood cavity.
5 Tech Tip 7 Wire pulled through. Step 8 Pull the black and red wire through for about 2 feet and un-tape the fish wire. Step 9 Feed the fish wire through the hood cavity as shown. Step 10 Tape the black and red wire to the fish wire.
6 Step 11 Pull the black and red wire through the hood cavity. Continue pulling until you have about 1 foot of wire showing. Step 12 Disconnect the fish wire. Step 13 Determine the location of the light strip. The location should be based on the following considerations: Apply to a clean flat surface. Install where the lights will shine on the engine compartment. Lights will not be damaged when the hood is closed. Light strip will not extend past the hood. Once the light strip location is determined, clean the area using brake cleaner and a cloth. Note: This is so the light strip will adhere to the hood better.
7 Step 14 To further enhance adhesion of the light strip, wipe down the area with the alcohol wipes provided in the kit. Step 15 Adhere the light strip to the hood. Starting with the end of the light strip where the black and red wires are, begin pealing off the backing. Step 16 While pealing off the backing, stick the light strip to the hood. Press the light strip firmly into place insuring good adhesion. Step 17 Remove excess 26 gauge wire from the light strip using wire cutters. Caution: Do not cut too short. Leave yourself plenty of length to work with. We recommend 6 to 8 inches at least.
8 Step 18 Separate the two wires so they can be stripped. Step 19 Remove about 3/4 of insulation from both (Black and Red) wires using a 26 gauge wire stripper. Step 20 Twist the conductor strands together and wrap the conductor back around the insulation on both (black and red wires) as shown on the black wire here. (See Tech Tip 20) Tech Tip 20 Shows how to wrap the conductor around the insulator. Note: We wrapped the conductor around the insulation to make a better connection.
9 Step 21 Place the wire inside the supplied butt connector as shown. Note: Be sure the wire fits all the way down inside the metal part of the butt connector. Step 22 Crimp the butt connector on to the black wire. Then install a second butt connector on the red wire in the same manner as you did the black wire. Note: Be sure the crimping tool fits over the metal part of the butt connector. After crimping, tug gently on the connectors to be sure they are secure. Step 23 Strip both (black and red) 20 gauge wires. Step 24 Connect the red 20 gauge wire to the red 26 gauge (LED) wire and the black 20 gauge wire to the black 26 gauge (LED) wire. Note: Tug gently on each connection to be sure they are tight and secure.
10 Step 25 These butt connectors can be heated to shrink them down tight on the wire making a weatherproof connection. This can be done with a heat shrink heating tool, a cigarette lighter or even a match. Be careful not to overheat. It is easy to met the heat shrink material. Step 26 If possible, tuck the wires and butt connectors inside the hood cavity. Step 27 Remove any excess slack in the wires by pulling the wires back down through the hood. Tech Tip 27 This shows the slack being removed from the wire. Caution: Be careful not to pull too hard so as to break the wires loose from the butt connectors.
11 Step 28 Route the 20 gauge (black and red) wire such that it will not be damaged when the hood is closed. Also, make sure the wires are routed away from any other potentially damaging parts. Tech Tip 28 Notice how the windshield washer hose is routed and try to do something similar with the under hood 20 gauge wires. Step 29 Secure the 20 gauge wires in several places with the supplied zip ties. Step 29 Continued This shows the second zip tie location.
12 Step 29 Continued This shows the third zip tie location.
13 Method of Connecting the Red (or Positive) Wire to a Positive Power Source - Option 1 Comprising Steps Step 30 Locate a blank space in the fuse box that does not have a fuse in it and has power to one side with the ignition switch in the OFF position. This can be determined by using a common 12V test light or Power Probe as shown here. Step 31 Insert the supplied spade fuse box tap in the location determined in the previous step. Fuse Tech Tip 31 This shows a spade fuse box tap. Step 32 Connect the 20 gauge red wire to this fuse box tap. It may be necessary to modify the fuse box lid to allow the wire to pass through.
14 Method of Connecting the Red (or positive) Wire to a Positive Power Source - Option 2 Comprising Steps Toward Light Strip Toward Battery + Step 33 The 20 gauge red wire could be connected directly to the positive connection on the battery. Step 34 If you choose this option. Be sure to place the supplied fuse in series, to protect the circuit. Method of Connecting the Red (or positive) Wire to a Positive Power Source - Option 3 Comprising Steps 35-35B Step 35 Select an unused connection on this add on fuse block. Since this fuse block was already installed this is the option we chose. Tech Tip 35A This is the auxiliary blade fuse block that was already installed on this vehicle. It works very well when adding extra components to a vehicle. Note: Click HERE if you are interested in purchasing one of these fuse blocks from Low Range Off-Road.
15 Connect to this Screw Fuse Tech Tip 35B We made our connection here. Keep in mind you will need to add a fuse to make this work. 1A is what we recommend.
16 Connecting the Red (or positive) Wire to the Positive Power Source Step 36 Separate the black and red wire as far as needed to route the red wire properly. Note: Make sure the wires are routed in a safe place; away form any moving parts, sharp edges or heat sources. Step 37 Route the red wire to the 12V power source selected earlier using option 1, 2 or 3. Step 38 Estimate the length needed. Step 39 Cut the red wire to length. Note: Always cut the wire a bit longer than you really need to insure the wire will reach once you have added the connector.
17 Step 40 Strip the insulation from the wire. Usually about 1/4 is sufficient. Step 41 Install and crimp the supplied eyelet electrical connector. Step 42 Shrink the insulation by applying heat. Step 43 Connect the eyelet connector to the fuse block. Caution: It is best to leave the fuse out for now. This will guard against any accidental short circuiting.
18 Installing the Ground Wire Step 44 Determining where to install the ground switch. We recommend placing the switch as close to the hood stop as possible. This will give you a good idea as to how high to adjust the switch. Be sure that the switch has enough room below the installation location to extend downward without obstruction when the hood is in the closed position and the switch is fully depressed. The area of the hood that contacts the switch should be as flat (horizontal) as possible so as not to force the switch in a lateral (side-to-side) direction. Hood Stop Step 45 Drill a 5/16 hole in the location selected for the switch using the supplied 5/16 drill bit. We chose to drill this hole about 2 inboard of the hood stop. Bottom Nut and Washer Step 46 Remove the paint around the hole so the switch can make a good electrical ground. Step 47 Remove the bottom nut and washer.
19 Step 48 Insert the switch in the hole. Step 49 Install the washer and nut. Note: If the switch will not fit in the hole, you may need to ream the hole a bit more with the drill bit. The drill bit we supplied was sized a little small to insure a good, snug, electrical ground. Step 50 While holding the top nut with a 12mm open end wrench, tighten the bottom nut with a second 12mm wrench. Step 51 Check for proper adjustment. When the button is depressed all the way, it should be about 1/4 below the hood stop. Adjust as needed.
20 Step 52 Now push the switch all the way down and check under the mounting surface to see that there is no obstruction. If the switch hits ANYTHING you will need to make some sort of adjustment. You may need to bend the body a bit to gain the necessary clearance. Although it is not likely, you may need to relocate the switch by drilling the hole in another place. Step 53 Estimate the length of the ground wire. Be sure to leave plenty of length. Then, cut, strip and crimp the supplied female spade connector. Tech Tip 53 Female Spade Connectors. Step 54 Connect the female spade connector to the bottom of the ground switch.
21 Step 55 Install a 1A fuse. Step 56 With the ground switch in the up position the under hood lights should come on. If the lights come on go to the next step. If not check all connections and the fuse for proper condition and repair as needed. Step 57 Slowly lower the hood about 1/2 way and check to see that the wire near the hood hinge is routed in a safe place. Step 58 Continue closing the hood. When the hood is approximately 1 away from completely closing, the lights should go out. If they do, move on to the next step. If not, open the hood and adjust the switch up a little and try again.
22 Step 59 Close the hood all the way. If it closes properly with out obstruction and the lights go out as they should, the switch is properly adjusted. Congratulations! You have successfully installed an Under Hood LED light Kit. We hope these instructions have been helpful. If you have suggestions on how to make these instructions (or products) better, please us at:
23 As always, If you experience any difficulty during the installation of this product please contact Low Range Off-Road Technical Support at M-F during regular store hours. Thank you for purchasing from Low Range Off-Road. These instructions are designed as a general installation guide. Installation of many Low Range Off-Road products require specialized skills such as metal fabrication, welding and mechanical trouble shooting. If you have any questions or are unsure about how to proceed, please contact our shop at or seek help from a competent fabricator. Using fabrication tools such as welders, torches and grinders can cause serious bodily harm and death. Please operate equipment carefully and observe proper safety procedures. Rock crawling and off-road driving are inherently dangerous activities. Some modifications will adversely affect the on-road handling characteristics of your vehicle. All products sold by Low Range Off-Road are sold for off road use only. Any other use or application is the responsibility of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may under certain circumstances void your original dealer warranty. Modification of your vehicle may create dangerous conditions, which could cause roll-overs resulting in serious bodily injury or death. Buyers and users of these products hereby expressly assume all risks associated with any such modifications and use. Revised 12/03/14 Copyright 2014 Low Range Off-Road, LC All Rights Reserved
Installation Instructions
Instructions Created by an: Suzuki Samurai 1.3L Replacement Throttle Cable (SKU# SER-THC) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationInstallation Instructions
Instructions Created by an: Suzuki Samurai Door-less Mirror and Light Mount by Low Range Off-Road (SKU# SEB-LR-DMB) Installation Instructions CAUTION: Safety glasses should be worn at all times when working
More informationInstallation Instructions
86-95 Suzuki Samurai Replacement U-bolts, Stock and Extended Length (SKU# SSP-UB) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More informationInstallation Instructions
Instructions Created by an: Suzuki Samurai Roof Rack Kit for Hard Top, Tin Top by Low Range Off Road (SKU# SEB-RRTT) Installation Instructions CAUTION: Safety glasses should be worn at all times when working
More informationInstallation Instructions
Instructions Created by an: Samurai Rear Diamond Plate Corners (Pre-bent) (SKU# SEB-RDP) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationInstallation Instructions
Steering kit for Samurai Cross Over Steering Kits (SKU# SST-SSOTS) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and equipment.
More informationInstallation Instructions
Instructions Created by an: Suzuki Samurai Replacement Clutch (SKU# STM-CC) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and
More informationInstallation Instructions
Instructions Created by an: Suzuki Sidekick / Tracker / X90 / Vitara / Grand Vitara Defiant Armor Differential Guard (SKU# KAR-DG) Installation Instructions CAUTION: Safety glasses should be worn at all
More informationInstallation Instructions
86-89 Suzuki Samurai Pedal Rebuild Kit SKU# SIB-PRB! Instructions also includes clutch adjustment procedures. Installation Instructions W e a l s o s u p p l y replacement peddle pads. Click HERE for more
More informationInstallation Instructions
Instructions Created by an: DIY Alignment Toe Set Tool, 5 Patterns (SKU# DIY-TST) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More informationInstallation Instructions
86-95 Suzuki Samurai Corbeau Safari Fold And Tumble Rear Seat Bracket Seat Kit (SKU# SIB-RSBR) Instructions also Include:! SKU# CS-SAF Corbeau Safari Reclining Fold & Tumble Bench Seat!!!!! SKU# CS-2SB-LB
More informationLOW RANGE OFF-ROAD Suzuki Samurai Venturi Vent Tube Nozzle (SKU# SER-VENT) Installation Instructions
86-88 Suzuki Samurai Venturi Vent Tube Nozzle (SKU# SER-VENT) Installation Instructions For a video of this procedure click HERE, or go to our web site. Suggested Tools: CAUTION: Safety glasses should
More informationSuzuki Samurai Coated Stainless Steel Braided Brake Lines (SKU# SB-BL) Installation Instructions
Suzuki Samurai Coated Stainless Steel Braided Brake Lines (SKU# SB-BL) Installation Instructions SUZUKI SAMURAI FRONT BRAKE LINES SUZUKI SAMURAI REAR BRAKE LINES Notice: After completing this installation
More informationInstallation Instructions
Instructions Created by an: 1986-1995 Toyota Pickup 4Runner Hilux Front Ball Joint Spacer Kit - 2.5" 64mm Lift by Low Range Off-Road (SKU# TSP-BJS-1.5 & TSP-BJS-1.5-W/Shocks) Installation Instructions
More informationInstallation Instructions
86-95 Suzuki Samurai Heater Water Control Valve Wire Cable (SKU# SIB-HCVW) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and
More informationToyota Tundra Sequoia Differential Drop Kit by Low Range Off-Road (SKU# LR-TUNDDK)
Instructions Created by an: 2007-2015 Toyota Tundra 2008-2015 Sequoia Differential Drop Kit by Low Range Off-Road (SKU# LR-TUNDDK) CAUTION: Safety glasses should be worn at all times when working with
More informationInstallation Instructions
86-95 Suzuki Samurai Hood Latch & Release Cable (SKU# SEB- HLCK) Installation Instructions Note: S u z u k i h a s upgraded both of these parts and they will not work with the hood latches and release
More informationSuzuki Samurai Full Time 4WD Drive Flange Kit (SKU# SAX-DF)
Instructions Created by an: Suzuki Samurai Full Time 4WD Drive Flange Kit (SKU# SAX-DF) We recommend that you consider replacing the hub bolts when installing this kit. Click HERE for more info. CAUTION:
More informationInstallation Instructions
Instructions Created by an: 2005+ Toyota Tacoma BTB Front Coilovers by Low Range Off Road SKU# TAC-SP-05CO-BTB-650 Diff Drop Kit (SKU# LR-2GDDK) Instructions included Installation Instructions Revised
More informationInstallation Instructions
86-88 Suzuki Samurai Heater Control Valve (SKU# SER-HCV) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and equipment. Suggested
More informationInstallation Instructions
Suzuki Samurai 1 Inch and 2 Inch Body Lift Kit (SKU# SSP-BL) Installation Instructions Background: These instructions are designed for installing the 2 body lift. Our approach is to raise the entire body
More informationInstallation Instructions
Instructions Created by an: 2007-Present Toyota Tundra LRT Leveling Lift Kit - 4WD by Low Range Off-Road (SKU# LR-LRTundra) Instructions also apply to 2WD Kits. Installation Instructions Revised 7-11-17
More informationInstallation Instructions
Instructions Created by an: Inchworm Tacoma Dual Case Adapter Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools
More informationLow Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2
Low Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2 Installation Instructions Background: These instructions are designed for installing the 2 body lift. They can also be
More informationSuzuki Samurai to Toyota Front Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSFM) Installation Instructions
Suzuki Samurai to Toyota Front Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSFM) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationInstallation Instructions
Instructions Created by an: Revised 7-11-17 LRT 2005-2017 3/1 Leveling/ Lift Kit for Toyota Tacoma by Low Range Off-Road (SKU# LR-LRTACO) Installation Instructions Suggested Tools: CAUTION: Safety glasses
More informationInstallation Instructions
Instructions Created by an: Inchworm Gear Clockable Toyota Dual Transfer Case Adapter Kit, 21 or 23 Spline SKU# TCASE-IW-300-000 Installation Instructions CAUTION: Safety glasses should be worn at all
More informationInstallation Instructions
86-95 Suzuki Samurai Front Shackle (SKU# SSP-HDS1) Note: These instructions also apply to SKU# SSP-HDS3 Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when
More informationInstallation Instructions
86-95 Low Range Off Road Universal Front Shock Tower Kit for Suzuki Samurai (SKU# SSP-UST) Installation Instructions Revised 10/29/13 Suggested Tools: CAUTION: Safety glasses should be worn at all times
More informationInstructions Suzuki Samurai Brake System Bleeding. Suggested Tools:
86-95 Suzuki Samurai Brake System Bleeding Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and equipment. Suggested Tools: Brake Fluid, DOT
More informationInstallation Instructions
86-95 Suzuki Samurai HD Transfer Case Mount (SKU# STC-EOS) Revised 4/11/14 Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and
More informationInstallation Instructions
2003-Present Toyota 4Runner 2007-2014 FJ Cruiser 1.5" Rear Coil Spring Spacers by Low Range Off-Road (SKU# LR-FJ4RRS) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at
More informationInstallation Instructions
Instructions Created by an: Mini Spool for Samurai, Sidekick, Tracker, 26 Spline, Yukon (SKU# SAX-MS-YUK) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times
More informationInstallation Instructions
2003-Present Toyota 4Runner 2007-2014 FJ Cruiser LRT 3" Lift Kit by Low Range Off-Road (SKU# LR-LRFJ4RU) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when
More informationInstallation Instructions
Suzuki Samurai 26 Spline Lockright Locker w/o Couplers (SKU# SAX-1510) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationToyota V6 Adapter Plate, KIT
Toyota V6 Adapter Plate, 100086-1-KIT KIT Contents: 100086-1 Dual Adapter, V6 88-95 1.0 100088-1 Coupler, V6 23S-23S 1.0 100089-1 Bolt, M10-1.25x35 6.0 100091-1 Bolt, M10-1.25x30 Flat Head Allen Bolt 2.0
More informationInstallation Instructions
86-95 Suzuki Samurai Rear Wheel Bearing Kit (SKU# SAX-RWB) Instructions also include:! Rear Hub Bolt Kit!!!! (SKU# SAX-AS)!! SJ410 Backing Plate!!!! (SKU# SAX-410)! SJ413 Rear Drum Brake Hardware Kit!
More informationTrail-Creeper Dual Transfer Case Adapter
Trail-Creeper Dual Transfer Case Adapter Installation Instructions For Kits: 100001-1-KIT 21 Spline 100006-1-KIT 23 Spline KIT Contents: 23 or 21 Spline Coupler 1.0 Adapter Plate w/ Bearings Installed
More informationSuzuki Samurai 6.5 Transfer Case Gear Kit, KIT
Suzuki Samurai 6.5 Transfer Case Gear Kit, 105004-3-KIT Kit Contents: Gear, 26 Spline/26 Tooth 1.0 Gear, 44 Tooth 1.0 Gear, 58 Tooth/23 Tooth 1.0 Gear, 67 Tooth/ 27 Tooth 1.0 Counter Shaft 1.0 Counter
More informationIFS Eliminator Kit,
IFS Eliminator Kit, 110001-1 IFS Eliminator Kit Contents: Front Leaf Springs (choice 3", 4", or 5") 1.0 High Steer Crossover Steering Kit 1.0 Frame Tube Jig Kit 1.0 Steering Stabilizer Kit 1.0 U-bolt Flip
More informationInstallation Instructions
Suzuki Samurai Rear Disk Brake Kits by Low Range Off Road (SKU# SB-LRD) Also included in the instructions are:!!! SB-LRDB Suzuki Samurai Disk Brake Bracket Kit by Low Range Off Road!!! SB-LRDB-FK-1 Suzuki
More information86-95 Suzuki Samurai Complete Contact Spring Over Axle Pads (SKU# SSP-CCSP4) Installation Instructions
86-95 Suzuki Samurai Complete Contact Spring Over Axle Pads (SKU# SSP-CCSP4) Installation Instructions Revised 4/17/18 Front Pads (SSP-CCFP) Rear Pads (SSP-CCRP) Suggested Tools: CAUTION: Safety glasses
More informationInstallation Instructions
Instructions Created by an: 86-95 Suzuki Samurai Samurai Front Axle Knuckle Rebuild Kits (SKU# SAX-KRK) Installation Instructions Revised 6-6-14 Suggested Tools: CAUTION: Safety glasses should be worn
More informationInstallation Instructions
99-04 Suzuki Sidekick 2 Inch Budget Lift Kit Also fits 99-04 Tracker, Vitara, Grand Vitara or XL-7 Instructions Include:! SKU# KSP-BLKV Basic Kit!!!! SKU# KSP-C2BLKV-RS Basic Kit W/Rear Shocks!!!! SKU#
More informationInstallation Instructions
) Instructions Created by an: Suzuki Sidekick / Tracker "Game Changer" 4 Speed Auto to Toyota T-Case Adapter Kit (SKU# KTC-GC-21, KTC-GC-23) Installation Instructions Suggested Tools: CAUTION: Safety glasses
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationHush-O-Matic MRS Control Package
Hush-O-Matic MRS Control Package 06-49192 Congratulations on your purchase! The Hush-O-Matic MRS Control package allows you to choose a few different modes including always quiet and always loud. Controlling
More informationYour Legal Fuel Tank Source.
February 23, 2015 IS# 808 Page 1 of 13 THANK YOU FOR PURCHASING A TRANSFER FLOW 40 GALLON TOOLBOX REFUELING SYSTEM. PLEASE READ THE FOLLOWING PROCEDURES CAREFULLY BEFORE STARTING THE INSTALLATION. CAUTION:
More informationTrail Rocker Installation
Trail Rocker Installation Instructions Customizable Trail Rocker Control System For Installing Painless Part Number: 57100 Manual #90616 Painless Performance Products recommends you, the installer, read
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationCurb-Alert Installation Guide: C7 Stingray
Rev. 2014-07-28 Curb-Alert Installation Guide: C7 Stingray Page 1 of 18 To complete this procedure, you will need the following items: 13mm Socket (deep or standard will work) Flat head screw driver Coat
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationTrack Rocker Installation Instructions
Track Rocker Installation Instructions Customizable Track Rocker Control System For Installing Painless Part Number: 58100 Track Rocker Relay Center Manual #90641 Painless Performance Products recommends
More informationRemove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor.
2015 Ford Mustang Turn Signal Hood Kit Parts List: Quantity: Tool List: Bracket & pre-installed lamp 2 Flat head screwdriver Wiring harness 1 Phillips screwdriver PB-3660 Parts Bag 1 Ratchet & Socket set
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationINSTALLATION GUIDE. AV8900H Dual Multimedia Headrest Replacement System
INSTALLATION GUIDE AV8900H Dual Multimedia Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE AV8900H VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED
More informationI N S T A L L A T I O N G U I D E
I N S T A L L A T I O N G U I D E APPLICATION LENGTH MODEL YR PART # Ford F-250 / F-350 / F-450 Regular Cab * (48 ) 2008-2016 76234-01A Ford F-250 / F-350 / F-450 Super Cab * (60 ) 2008-2016 76234-01A
More informationI N S T A L L A T I O N G U I D E. Ford Transit - Single Sided A (All slider and barn door models)
I N S T A L L A T I O N G U I D E APPLICATION MODEL YR PART # Ford Transit - Single Sided 2014-2017 76159-01A (All slider and barn door models) INSTALLATION TIME 3-5 Hours Professional installation recommended
More informationTRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL SADDLE BOX STARTER KIT. Model: QDSKSA01. Part No.
TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL SADDLE BOX STARTER KIT Model: QDSKSA01 Part No. 24-0326 Rev. A ECN 5430 ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS
More informationRecommended tools: Estimated install time: Parts list:
Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi A4/S4. While the install is fairly straight forward, please review these instructions carefully before attempting
More information3-5 Hours Professional installation recommended
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Chevrolet Silverado500 / GMC Sierra 500 - Double Cab * 04-7 7554-0A Chevrolet Silverado500 / GMC Sierra 500- Crew Cab 04-7 7554-0A Chevrolet Silverado
More informationINSTALLATION MANUAL. Power-Pole Blade Edition Shallow Water Anchor. Installation Instructions
INSTALLATION MANUAL Power-Pole Blade Edition Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate the
More informationWRX/STI Engine Oil Cooler
2002-14 WRX/STI Engine Oil Cooler 2014-04-21 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationTrail Rocker Installation Instructions
Trail Rocker Installation Instructions Manual #90580 For Installing Painless Part Numbers: 57000 and 57001 Painless Performance Products recommends you, the installer, read this installation manual from
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious
More informationTrail Rocker Installation
Trail Rocker Installation Instructions 4, 6, or 8 - Switch Customizable Trail Rocker Switch Panel w/ Flanged Mount For Installing Painless Part Number: 57103, 57106, & 57109 Manual #90636 Painless Performance
More informationCERTAIN TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE
PAGE 1 OF 19 CERTAIN 2015-2017 TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE OVERVIEW In the affected vehicles, it may be possible for water to pool and
More information* * APPLICABLE MODELS: 2017 > CX-5
PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationSCION tc ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill
More informationAux. Battery and Isolator
Aux. Battery and Isolator ISOLATOR MOUNTING ALL YEAR VANAGONS Fig.1 1. Disconnect ground from main battery under passenger seat 2. Remove driver seat 3. Remove driver seat belt buckle from seat pedestal
More informationStep #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good t
How to make a ROV! Step #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good to have extras. Using the wire cutter,
More information= Experienced
I N S T A L L A T I O N G U I D E APPLICATION LENGTH MODEL YR PART # Ford F-250 / F-350 / F-450 Regular Cab * (48 ) 2002-2003, 2008-2016 75134-01A Ford F-250 / F-350 / F-450 Super Cab * (60 ) 2002-2003,
More informationInstallation Tips for your Remote Start system (for Toyota Camry & Prius C, ) Crimestopper RS0+ EVO-ALL T3468 rev#1.
Installation Tips for your Remote Start system (for Toyota Camry & Prius C, 2012-2014) Crimestopper RS0+ EVO-ALL T3468 rev#1.1 1/22/2015 Thank you for purchasing your remote start from MyPushcart.com -
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationSPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER. Read entire instructions thoroughly before starting. INSTALLATION INSTRUCTIONS TOOLS REQUIRED:
Read entire instructions thoroughly before starting. TOOLS REQUIRED: SPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER INSTALLATION INSTRUCTIONS Complete socket set Phillips screwdriver Torx drivers Wire strippers/cutters
More informationWiring Harness Update Kit Assembly Instructions Treker 4200/4400 NT & ST Series Manual No M
Wiring Harness Update Kit Assembly Instructions Treker 4200/4400 NT & ST Series Manual No. 700-364M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS
TITAN pt. no.: 99 0000 0509 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS I n B e d F u e l T a n k Shown
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More information2-3 Hours Professional installation recommended
INSTALLATION GUIDE APPLICATION AMP Part # Chevrolet Silverado1500 / GMC Sierra 1500 - Double Cab * 2014-18 78154-01A Chevrolet Silverado1500 / GMC Sierra 1500- Crew Cab 2014-18 78154-01A Chevrolet Silverado
More informationPart# JL AIR IT UP 4 Tire On Board Air Delivery System. (Requires External Air Source)
Part# 18-1819 JL AIR IT UP 4 Tire On Board Air Delivery System (Requires External Air Source) The most up-to-date instructions always visit www.updownair.com www.updownair.com 833-226-4863 I M P O R T
More informationThe Go Baby Go Build Manual
The Go Baby Go Build Manual The step-by-step guide to creating your own Go Baby Go Car 4488 Shockwave Robotics and Pacific University Index 1. List of Mat erials 2. Mechanical Assembly a. Installing the
More informationIT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.
Instructions for Universal Harness PRINT THESE INSTUCTIONS Gentex Mirror Installation Instructions Provided by www.rearviewautomirrors.com These instructions have been prepared to provide you with details
More informationConflicts: Vehicles with a sunroof
Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:
More informationATTENTION. Custom Dynamics UTV Turn Signal Kit Installation Instructions
Custom Dynamics UTV Kit Installation Instructions We thank you for purchasing the Custom Dynamics UTV LED Kit. Our products utilize the latest technology and high quality components to ensure you the most
More information#GL18006-L2 Honda Gold Wing 1800 & F6B models - All Years Lower Cowl LED Driving Lights INSTALLATION INSTRUCTIONS
#GL18006-L2 Honda Gold Wing 1800 & F6B models - All Years Lower Cowl LED Driving Lights INSTALLATION INSTRUCTIONS 1. Lay out and familiarize yourself with the parts included in the set. Remove the left
More informationI N S T A L L A T I O N G U I D E. Chevrolet Silverado / GMC Sierra - Ext Cab * A (Diesel Only)
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Chevrolet Silverado / GMC Sierra - Crew Cab 2011-201 751-01A (Diesel Only) Chevrolet Silverado / GMC Sierra - Ext Cab 2011-201* 751-01A (Diesel
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationFord 6.7L Installation of the Guardian Safety System
Ford 6.7L Installation of the Guardian Safety System Diesel Tech Industries Ltd. 14215-120 Avenue Edmonton, Alberta, Canada T5L 2R8 Phone: (780) 455-9876 info@dtiguardian.com www.dtiguardian.com DTI05-02.01/13
More informationContents. TCS/ Driver Mod Installation Manual
Contents Introduction... 1 TCS Packing List... 3 Tools Needed for Installation... 4 How to Properly Solder... 5 Soldering Standard Butt Connection... 5 Soldering T Connection... 6 How to Properly Crimp...
More informationGentex Homelink Installation Instructions
Gentex Homelink Installation Instructions Kit Contents: Item Qty Part Description 1 Number GENK-41 NVS Homelink Mirror GENK-42 NVS Homelink w/mood lights 1 of the GENK-45 NVS Homelink w/compass following
More information* * APPLICABLE MODELS: 2014 > Mazda 3
PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More information3-5 Hours Professional installation recommended
I N S T A L L A T I O N G U I D E APPLICATION MODEL YR PART # Toyota Tacoma Double Cab 2016 75162-01A Toyota Tacoma Access Cab* 2016 75162-01A * Modification required to running board assembly. See Item
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More information