REVIT CONTENT GUIDE. Instance Properties. Manufacturer: File: Type Catalog: Rendering file: Schedule file:

Transcription

1 REVIT CONTENT GUIDE Manufacturer: File: Type Catalog: Rendering file: Schedule file: Cummins Power Generation, Inc. Generator_Diesel-QSK60-Cummins_Power-Ghost.rfa Not Applicable Not Applicable Schedule - Generator_Diesel-QSK60-Cummins_Power-Ghost.rvt Instance Properties Analytical Model Octave Band Hz* Octave Band Hz* Octave Band Hz* Octave Band Hz* Octave Band Hz* Octave Band Hz* Octave Band - 63 Hz* Octave Band Hz* Sound Power Level* Sound Pressure Level* Construction Alternator Model* MVSI804X Alternator Model is HVSI804X Alternator Model is LVSI804X Alternator Model is MVSI804X Configuration Available Has Control Box Has Spring Isolators Has Terminal Housing Bottom Entry Has Terminal Housing Top Entry Radiator Selection* Radiator is DQKAN 45 deg C Terminal Housing or Entrance Box Configuration* No Option Selected Data Cooling Coil Air Pressure Drop* in-wg Graphics Clearance Depth Generator End Clearance Depth Radiator End Show Clearance Areas Identity Data Equipment Number* Part Description* 2500 kw STANDBY Diesel Generator Set Part Number* DQKAN Page 1

2 Structural Operating Weight* Weight Disclaimer lb Wet Weight Value is Approximate and Calculated Fom the Configurable Options Type Properties The family contains the following 1 types: DQKAN kw Standby Power (Values for this type are shown below) Adsk Model Properties Engine Model* QSK78-G12 Analytical Model Exhaust Octave Band Hz* Exhaust Octave Band Hz* Exhaust Octave Band Hz* Exhaust Octave Band Hz* Exhaust Octave Band Hz* Exhaust Octave Band Hz* Exhaust Octave Band - 63 Hz* Exhaust Octave Band Hz* Construction Coolant Heater is 40 Deg F Ambient Coolant Heater is Sub 40 Deg F Ambient Data Emissions CO (g/hp-hr)* Emissions HC (g/hp-hr)* Emissions NOx (g/hp-hr)* Emissions PM (g/hp-hr)* Emissions SO2 (g/hp-hr)* Engine Lube Oil Capacity* gal Exhaust Gas Flow Rate* CFM Exhaust Stack Gas Temp* F Exhaust System Backpressure* in-wg Fuel Consumption Rate at Full Load* gal/h Heat Rejection to Aftercooler Circuit Coolant* Btu/h Heat Rejection to Jacket Water Coolant* Btu/h Page 2

3 Electrical Amperage* 0.43 ka Bus Voltage* V Coolant Heater Voltage* V Coolant Heater Voltage is 208 V Coolant Heater Voltage is 240 V Coolant Heater Voltage is 480 V Coolant Heater Voltge Selection 208 V Coolant Heater Wattage* W Frequency* Hz Load Classification* Power Number of Poles* 3 Power Rating* kw Voltage 4160 Voltage is Voltage is Voltage is Voltage is 416 Voltage is 4160 Voltage is 440 Voltage is 480 Voltage is 600 Wattage 2500 Electrical Loads Apparent Load Phase A* Apparent Load Phase B* Apparent Load Phase C* Identity Data Copyright* Copyright 2011 Cummins Power Generation, Inc. Date Last Modified* September 16, 2013 Description 2500 kw STANDBY Diesel Generator Set Equipment Abbreviation* GS Family Version* Manufacturer Cummins Power Generation, Inc. Model DQKAN Model Disclaimer* This Model Represents a Highly Customizable Piece of Equipment. For Accurate Selection Data, Contact Cummins Power Generation, Inc. Original Creation Date* September 16, 2013 Product Documentation Link* Product Page URL* Provide Feedback* URL Materials Product Material* Steel - Cummins - Green Halftone text in the property tables indicates that the value is locked from editing. *Indicates Shared Parameter and can be scheduled Loading and Placing into the Project One "Electrical Equipment" family is supplied and can be loaded into a Revit project through all traditional methods. The generator requires a work-plane host to be placed within the project (i.e. floor). Also, ensure that the visibility settings within the project are modified to have the Electrical Page 3

4 Equipment category visible. The Generator will come into the project with a transparent red box (clearance area) around it, deselect the Show Clearance Areas option to hide the clearance area. Project Behavior Within the type and instance properties dialogues, the user will find useful information for scheduling purposes such as Engine Model, Frequency, and other unique properties of the model. In Identity Data the user will find information specific to Cummins Power Generation, Inc. and the model, i.e.: family revision information, Cummins Power Generation, Inc. copyright information, part description, product URL and other specific data. *See scheduling description below. There are many options that are specific to one or a few types within the generator family, if an unavailable selection is made a red error box will surround the generator. The cause of the error and how to fix is can be found by referencing the construction parameter Configuration in the instance window. The generator features many different options in order to configure the product as necessary. Certain options can be utilized to change between alternators or to swap out the standard air cleaners for a heavy duty set. For more information about the available options and how they affect the model, *see Instance Parameter section below. Instance Parameter In the Instance Parameters, the user has the following options to modify: Equipment Number - For tagging each placed instance. Has Terminal Housing - For selecting either a top or bottom entry terminal housing for the right side of the generator. Has Spring Isolators - For selecting the use of the spring isolators. Has Heavy Duty Air Cleaners - For toggling between the standard and heavy duty air cleaners. Has Control Box - For selecting the use of a control box. Alternator Model is... - Use options to select an alternator for the generator. Show Clearance Areas - For toggling the visibility of the clearance area. Type Parameter Each type represents a manufactured product. Therefore, the type parameters should not be modified by the user for standard configuration. Please note: Product Documentation Link Directs a webpage to the products online listing. Equipment Abbreviation For filtering schedules. *See scheduling description below. Coolant Heater is 40 Deg F Ambient For toggling between the 40 deg F or Sub 40 deg F Coolant Heater. Voltage is - For selecting the desired voltage for the generator. Coolant Heater Voltage is - For selecting the desired Coolant Heater Voltage. Visibility For best performance, all model geometry is turned off inall views and represented through masking regions and symbolic/model lines that update automatically when a user changes view properties. Rendering When the family file is loaded into the project, standard Wiremold materials are imported. These may be modified, though ensure that the modification selection matches an actual manufacturer supplied option. Page 4

5 Schedule Creation Cummins Power Generation, Inc. products may be scheduled utilizing the schedule view in the given project file. Select and copy (Ctrl-C) the schedule from the sheet view and paste it (Ctrl-V) into a sheet in your project. The schedule filters are set to look for only those units designated with Manufacturer as Cummins Power Generation, Inc." and Equipment Abbreviation as "GS". Page 5