Steel base polished and plated or furnished in prime or powder coat finish. Available Sizes. Inches MM Gauge

Transcription

1 McKINNEY Hinge Catalog Full Mortise Bearing Hinges Five Knuckle Standard Weight Series TA2314 TA2714 Available Options: Stainless steel base or available in brass or bronze base material polished and plated or furnished in prime or powder coat. Steel base polished and plated or furnished in prime or powder coat finish. NRP (non-removable pin) TB (ball bearing) TCA (concealed bearing) RC (round corner - 1 4" radius furnished unless specified otherwise) HT (hospital tip) BT (ball tip) ST (steeple tip) SSF (safety stud feature) QC (ElectroLynx hinge) 2, 4, 6, 8, 10 or 12 wire available CC (concealed circuit) 4, 6 or 8 wire available* CS- (concealed switch - handing required)* MM (magnetic monitoring) S (sherardizing, our additional rust resistant base under prime coat on steel base) Slip In (Type 1 or Type 2) Beveled Edge (where doors are beveled on hinge side specify TA4314 or TA4714) APPLICATION Available Sizes Inches MM Gauge x x x x x x x x x x x x x 6* x *Not available in Stainless * Not available in Stainless Packing: All standard weight full mortise non-ferrous hinges are packed with all machine x 1 2 wood screws. Steel hinges (except USP) are packed all machine x all wood screws. For special screws consult price book on availability. ANSI Cross Reference: McKINNEY Products Company 2006 Recommended for standard weight, medium frequency doors, or doors with closing devices. A2112 Brass, Bronze A5112 Stainless A8112 Steel January An ASSA ABLOY Group company

2 McKINNEY Hinge Architectural Hinges by McKinney Page 1 of 2 10/6/2010 Product Description nmlkji Catalog No: nmlkj Click Here For Catalog PDF's Hinge Thresholds and Weatherstrip Architectural Door Trim NOTE: We reserve the right, without notice, to make changes in specifications, construction, design, and details at any time in such manner as we may consider necessary or advisable. Corrections to reflect any such changes shall be included in subsequent updates to this website.

3 Overview Applications Access 600 TM RNE1 is ideal for Corporate campuses Educational facilities Healthcare facilities Government facilities Mortise Lock - ML20600 x RNE1 Cylindrical Lock - CL33600 x RNE1 Exit Device - ED5000N x 9600 x RNE1 Wiegand Open Architecture: Cost effective, easy system expansion Integrates mechanical door hardware with existing access control system The reader is housed within the exterior escutcheon* and works with 125 khz prox or MHz iclass credentials. M802 The M khz (proximity) version of Open Architecture Wiegand Access Control Platform offers a high level of security and convenience. The M802 requires a proximity card/fob/tag presentation to gain entry. The 125 khz reader operates on 12VDC. M812 The M MHz iclass (proximity) version of Open Architecture Wiegand Access Control Platform offers a high level of security and convenience. The M812 requires an iclass card/fob/tag presentation to gain entry. The MHz iclass reader operates on 12VDC or 24VDC. *Patent Pending Escutcheon Design corbinrusswin.com 2

4 Features ML20600 RNE1 Mortise Locks The Access 600 RNE1 mortise lock integrates into an existing Wiegand-compatible access control system and can monitor Latchbolt position, Request to Exit, and Door Position status, all within the lockbody. Secure door position monitoring feature ensures latchbolt is extended when door is closed. The Grade 1 Access 600 RNE1 mortise lock is designed to meet the rigors of high-traffic commercial, institutional, industrial and government applications. Constructed of heavy-gage steel, the lockbody features our patented Quick Reversible latchbolt, and a 1" stainless steel deadbolt. Features 12VDC or 24VDC solenoid operated mortise lock available as Fail Safe or Fail Secure (voltage must be specified) Monitoring Features Request to exit Secure door position monitors latchbolt and door position in series Handing Handed; quick reversibility The lockset can be re-handed without disassembling the lock body Door Thickness 1-3/4" (44mm) standard Optional door thicknesses in 1/8" increments available; see Quick Code section Backset 2-3/4" (70mm) Lockcase Heavy-gage chrome plated steel, 5-7/8" (149mm) x 4" (102mm) x 15/16" (24mm) Front Heavy-gage steel, 8" (203mm) x 1-1/4"(32mm) x 3/32" (2mm) Accommodates non-beveled and beveled doors Armored Front Wrought brass, bronze or stainless steel attached by machine screws to lockcase front Latch Patented, quick, reversible 2-piece mechanical with anti-friction insert 5/8" (16mm) x 1" (25mm) x 3/4" (19mm) U.S. Patent #6,349,982 Auxiliary Latchbolt 9/16" (14mm) effective throw and 3/8" (10mm) effective auxiliary latch deadlocking Deadbolt One-piece stainless steel, 19/32" (15mm) x 1-1/4"(32mm) x 1" (25mm) throw Standard trim is through bolted, not free floating Muséo trim is not through bolted, free floating Hub Steel, 5/16" (8mm) Strike Wrought brass, bronze or stainless steel ANSI straight lip standard, 4-7/8" (124mm) x 1-1/4" (32mm) x 1-1/8" (29mm) lip to center Optional strikes, lip lengths and ANSI wrought strike box available Cylinder A01, 6-pin, L4, keyed random, furnished standard for 1-3/4" (44mm) door Optional cylinders available Warranty 10-year limited mechanical 2-year limited electrical ANSI Meets A156.13, Grade 1 requirements Meets A117.1 Accessibility Code Meets A requirements 3

5 Escutcheons & Electrical Specifications ML20600 RNE1 Mortise Locks Highest point of projection 7/8" (22 mm) less lever 2-5/32" (55mm) Outside 7" (178mm) Escutcheons* Solid casting Highest point of projection 7/8" (22 mm) less lever Operating temperature -40 F (-40 C) to 135 F (57 C) LEDs indicate valid/invalid credentials Lever x sectional trim only Reader - M802 (125 khz proximity credentials) Reader requires 12 volts direct current 2-5/32" (55mm) Inside ML20600 x M802 Electrical Specifications: 12VDC System with 12VDC Solenoid Lock Reader Draw = 150mA (maximum) 12VDC Solenoid Draw = 800mA Total System Draw = 950mA 12VDC System with 24VDC Solenoid Lock Reader Draw = 150mA (maximum) 24VDC Solenoid Draw = 390mA Total System Draw = 540mA Highest point of projection 7/8" (22 mm) less lever 7" (178mm) Reader - M812 (13.56 MHz iclass credentials) Reader requires 12 volts or 24 volts direct current ML20600 x M812 Electrical Specifications: 12VDC System Reader Draw = 125mA (maximum) 12VDC Solenoid Draw = 800mA Total System Draw = 925mA * Patent Pending Escutcheon Design 24VDC System Reader Draw = 125mA (maximum) 24VDC Solenoid Draw = 390mA Total System Draw = 515mA 6

6 How to Order ML20600 RNE1 Mortise Locksets Function ML20610 x TCRNE1 ML20603 x TCRNE1 ML20660 x TCRNE1 ML20663 x TCRNE1 ML20630 x TCRNE1 ML20605 x TCRNE1 ML20680 x TCRNE1 ML20685 x TCRNE1 Lock Solenoid Voltage Quick Code Description Specify 12 Volts DC 24 Volts DC 12AD 24AD Finish* Description Specify Polished Brass, Clear Coated 605 Satin Brass, Clear Coated 606 Polished Bronze, Clear Coated 611 Satin Bronze, Clear Coated 612 Dark Oxidized Satin Bronze, Oil Rubbed Dark Oxidized Satin Bronze, Clear Coated 613L Polished Nickel 618 Satin Nickel 619 Polished Chrome 625 Satin Chrome 626 Satin Chrome with MicroShield 626C Bright Stainless Steel Satin Stainless Steel Satin Stainless Steel with MicroShield 630C Black Oxidized Bronze, Oil Rubbed Hand RH RHR LH LHR Credential M khz reader M MHz iclass reader Door Thickness Description Specify 1-3/4" (44mm) std 1-7/8" (48mm) D178 2" (51mm) D /8" (54mm) D /4" (57mm) D214 Consult factory for door thicknesses greater than 2-1/4 1 New, March Formerly 613 prior to March Escutcheon finished to match 629, 630 finish *See page 8 for finish options available for the Muséo Piet Lever Collection. For all quick codes see pages

7 125 khz Proximity Readers Corbin Russwin s line of proximity readers offers the latest technology and security. These readers can be mounted as required by the application [ie: in conjunction with electric latch retraction exit devices] on a wall or door frame. All units can be mounted inside and outdoors with vandal resistance construction. Wiegand Proximity Readers Product Number Function Description 752F F F F F F959 HID MiniProx model khz Mullion-mount Prox Reader Measures 6" high, 1.7" wide and 1" deep Mounts in junction box (included); 5-16VDC power supply required HID ThinLine II model khz Low Profile Prox Reader Measures 4.7" long, 3" wide and 0.68" deep Mounts in standard single gang electrical box; 5-16VDC power supply required HID ProxPro II model khz New Generation Prox Reader Measures 5" long, 5" wide and 1" deep Mounts in standard single gang electrical box; 5-16VDC power supply required HID ProxPro model khz Keypad Prox Reader (Keypad is configured for 8-bit data bursts) Measures 5" long, 5" wide and 1" deep Mounts in standard single gang electrical box, field adjustable for mounting directly to metal 10VDC VDC power supply required HID MaxiProx model khz Long Range Prox Reader (up to 24" prox range depending on prox credential used)) Measures 11.8" high, 11.8" wide and 1" deep Mounts on non-metallic surfaces; 12 or 24VDC power supply required HID ProxPoint Plus model khz Prox Reader Measures just 3.135" long, 1.72" wide and 0.66" deep Mounts inconspicuously on metallic surfaces such as mullions; 5-16VDC power supply required 752F979 HID model 5455 AGM00 Glass-mount kit for use with 752F929 and 752F939 For applications where reader will mount behind glass 29

8 Access Credentials The access credentials below are only compatible with the M802 (125 khz reader) option. Credential Features Only compatible with the M802 (125 khz reader) option Provides higher level of security when combined with keypad operation HID-based proximity cards, fobs or tags Allows integration into existing facilities with HID-based technology Standard credentials available with 26 bit Wiegand format and Corbin Russwin assigned site code HID credentials available with 26 bit and 33 bit format and customer assigned site code. For a higher level of security, custom cards, fobs or tags with unique site codes are available; consult factory. Corbin Russwin HID ProxCard II Only compatible with the M802 (125 khz reader) credential 26 bit format Blank (white) card or Corbin Russwin logo card 25/pkg. Dimensions: 2-1/8" x 3-3/8" (54mm x 86mm) Thickness:.070" nom. (1.8mm) 794F F F F389 C/R 26 bit ProxCard II blank ISO Prox II Only compatible with the M802 (125 khz reader) credential 26 bit format Blank (white) card or Corbin Russwin logo card Blank card can be printed with customer s text and graphics by others 25/pkg. Dimensions: 2-1/8" x 3-3/8" (54mm x 86mm) Thickness:.033" nom. (.84mm) 794F F F F369 C/R 26 bit ProxCard II with logo HID 26 bit ProxCard II with logo HID 26 bit ProxCard II without logo C/R 26 bit ISO ProxCard II blank C/R 26 bit ISO ProxCard II with logo HID 26 bit ISO ProxCard II with logo HID 26 bit ISO ProxCard II without logo DUO Prox II Only compatible with the M802 (125 khz reader) credential Multiple Technology Proximity Cards DuoProx dual technology, proximity and magnetic stripe technology. Enables integration into systems with existing magnetic swipe card readers Minimum order quantity: 100 each Custom cards or fobs with unique site codes for higher level of security 794F F F419 C/R DuoProx II - prox and magstripe with logo C/R DuoProx II - prox and magstripe w/o logo HID 26 bit DuoProx II - prox and magstripe MicroProx Tag The MicroProx Tag is a coin-sized (disk shaped) transponder that provides the ability to add HID proximity technology to a device. The MicroProx Tag has an adhesive backing which allows it to be secured to any non-metallic object. It is only compatible with the M802 (125 khz reader) credential. Easily Secured To: Employee badges PDAs Magnetic stripe cards Note: The MicroProx Tag should be attached to magnetic stripe cards so that contact with the magnetic card reader is avoided. Cell phones 26 bit format with Corbin Russwin site code or customer site code Sequence numbers marked on each Tag Gray color with HID Logo 10/pkg. (100 minimum order quantity) Dimensions: 1.285" x 0.070" (32.6mm x 1.78mm) For MicroProx Tag with customer site code, consult factory for minimum quantities 794F F449 C/R MicroProx tag HID MicroProx tag with customer site code 30

9 iclass Smart Card Readers iclass smart cards and readers make access control more powerful, more versatile, and most important of all, offer enhanced security through encryption and mutual authentication. At the same time, iclass is user-friendly, delivering the convenience, affordability and reliability of proximity technology. All Readers configured as follows: Wiegand output Standard iclass security (field configurable) Keypad: Buffer one key, no parity, 4 bit message (6130 ONLY) iclass Smart Card Readers Product Number Function Description 744F709 HID R10 Reader 6100 Mullion-mount Smart Card Reader Measures 4" long, 1.9" wide and.90" deep Mounts in single gang electrical box; 12VDC power supply required 744F719 HID R40 Reader 6120 Wall Switch Smart Card Reader Measures 4.8" long, 3.3" wide and 1.0" deep Mounts in single gang electrical box; 12VDC power supply required 744F729 HID RK40 Keypad Reader 6130 Wall Switch Keypad Smart Card Reader Measures 4.8" long, 3.3" wide and 1.1" deep Mounts in single gang electrical box; 12VDC power supply required 744F739 HID R90 Long Range Reader 6150 Wall Mount Smart Card Reader Read Only Measures 12" long, 12" wide and 1.25" deep Mounts in single gang electrical box; 12VDC power supply required 31

10 Accessories Requirements for Electrical and Data Transfer To answer the demand for "smart" electronic access control and locking solutions that require fast, easy, and cost-effective installation, ASSA ABLOY Group brands use the ElectroLynx standardized plug-in connectors and color-coded wiring system. With ElectroLynx, doorway components come pre-wired for easy hookup to the power source. Key to the system is the transfer device hinge that carries power from the frame to the locking hardware. Features of ElectroLynx: Makes it easy to bring power to the locking hardware Wires have connectors that snap together, like plugging a telephone into a jack To connect Access 600 RNE1 Series hardware to the electronic access control system, the following items are required: Access 600 RNE1 mortise or cylindrical lock, or exit device ASSA ABLOY Door Group pre-wired door, or ElectroLynx retrofit cable (order from McKinney) Electronic transfer device (ElectroLynx electronic transfer hinge or Electrical Power Transfer with standard hinge, from McKinney) ElectroLynx cable from the hinge to above the ceiling (order from McKinney) Information regarding cable selection, hinge requirements and order strings can be found in the McKinney Transfer Device Solutions catalog. Consult WIRE (9473) with questions on application specifications and requirements. McKinney QC12 ElectroLynx Hinges (or McKinney EL-EPT) are recommended for Access 600 RNE1 Applications Weatherseal Gasketing Gaskets provide sealing between escutcheons and door for exterior applications Gasketing and conduit recommended for use on non-fire rated exterior applications only To order separately, specify gasket part number(s) on page 35. Corbin Russwin ProxKey II Only compatible with the M802 (125 khz reader) credential 26-bit format Site code controlled by Corbin Russwin 10/pkg. (100 minimum order quantity) Dimensions: 1-29/32" x 29/32" x 11/32" (48mm x 23mm x 9mm) 794F F479 HID ProxKey II C/R 26 bit ProxKey II HID 26 bit ProxKey II Only compatible with the M802 (125 khz reader) credential 26-bit format Customer requested site code or range of fob numbers 10/pkg. Dimensions: 1-29/32" x 29/32" x 11/32" (48mm x 23mm x 9mm) To order specify 794F479 32

11 Accessories WT1 Wiegand Test Unit Designed for use with the Corbin Russwin Access 600 RNE1 Wiegand lock, the ASSA ABLOY Wiegand Test Unit is a user-friendly tool providing product demonstration to highlight important features and access control capabilities. Ideal for troubleshooting, the WT1 checks for: Proper wiring Card reader data integrity Lock functionality including lock/unlock, door position and REX WT1 Wiegand Tester Features: 12 or 24VDC solenoid lock voltage selectable Test in Fail Safe or Fail Secure locks Learn mode allows testing of specific cards without programming at the panel level Card reader data integrity is validated at test unit To order, specify WT1 33

12 Accessories, Parts and Quick Code Index Cylinder Options Part No./ Quick Code Description Cylindrical Mortise Exit Device 6P Conventional 6-pin std std 7P Conventional 7-pin LC Less Cylinder(s) std HS Security CHS Security IC PS Pyramid Security PCS Pyramid Security IC PHS Pyramid High Security Fixed Core PCHS Pyramid High Security IC CTP Pyramid IC with Temporary Construction Core CLP Pyramid IC Less Core C6 IC 6-pin CT6R IC 6-pin with Temporary Construction Core (Red) CT6B IC 6-pin with Temporary Construction Core (Blue) CT6G IC 6-pin with Temporary Construction Core (Green) CL6 IC 6-pin Less Core CLS6 SFIC 6-pin with Less Core CT6SD SFIC 6-pin with SFIC disposable temporary core CTSD SFIC 6- or 7-pin Small Format Disposable Core 1 C7 IC 7-pin CT7R IC 7-pin with Temporary Construction Core (Red) CT7B IC 7-pin with Temporary Construction Core (Blue) CT7G IC 7-pin with Temporary Construction Core (Green) CL7 IC 7-pin Less Core CLS7 SFIC 7-pin with Less Core CT7SD SFIC 7-pin with SFIC disposable temporary core CTPD Pyramid Disposable Core CT6D 6-pin with Disposable Core CT7D 7-pin with Disposable Core 0-bitted with 2 Blank Keys std std std KR Keyed random CMK Construction master keyed VKC0 Visual Key Control (VKC) - No bitting or keyset stamping on keys VKC1 Visual Key Control (VKC) - Keys only VKC2 Visual Key Control (VKC) - Cylinders and Keys (not for HS, CHS, PHS, or PCHS) VKC3 Visual Key Control (VKC) - Cylinders only (not for HS, CHS, PHS, or PCHS) CKC2 Concealed Key Control (CKC) - Cylinders with VKC keys CKC3 Concealed Key Control (CKC) - Cylinders Only (not for PHS, PCHS) 2 keys per Lock std std std KY# (e.g. KY6) More than 2 keys Note: 1. Specify M08 for levers to accept SFIC cores; which ship standard with temporary disposable core = available 36

13 Accessories, Parts and Quick Code Index Miscellaneous Options Part No./ Quick Code Description Cylindrical Mortise Exit Device M04 Torx head screws M06 Less cylinder, with tailpiece for Schlage cylinder M08 Lever to accept Best type core (NZD & PZD designs only) M09 Lever to accept Sargent cylinder (NZD & PZD designs only) M13 Rounded Corners on latch front M16 3/4" (19mm) throw fire latch M17 ANSI wrought strike box M20 Knurling outside and inside M21 Knurling outside only M22 Knurling inside only M23 Abrasive coat outside and inside M24 Abrasive coat outside only M25 Abrasive coat inside only M69 Lever to accept Schlage Interchangeable core (NZD & PZD design only) M54 Sex nuts and bolts (SNBs) M64 Wood screws for use on fire-rated solid wood or wood core doors M109 M110 High Impact End Clamp Flush End Cap Electrified Accessories BPS-24-1 Power supply VDC output BPS-24-2 Power supply 2 24 VDC output BPS-24-4 Power supply 4 24 VDC output BPS-12-1 Power supply 1 12 VDC output BPS-12-3 Power supply 3 12 VDC output EPTL Concealed transfer for over 120 swing doors 37

14 Accessories, Parts and Quick Code Index Strikes - ANSI Curved Lip Specify Lip to Center Cylindrical Mortise Exit Device SA100 1" (25mm) SA /8" (29mm) SA /4" (32mm) SA /8" (35mm) SA /2" (38mm) SA /4" (44mm) SA200 2" (51mm) SA /4" (57mm) SA /2" (64mm) SA /4" (70mm) SA300 3" (76mm) Strikes - ANSI Straight Lip Specify Lip to Center Cylindrical Mortise Exit Device SS078 7/8" (22mm) (standard) 1-1/8" (29mm) std SS /4" (32mm) SS /8" (35mm) SS /2" (38mm) SS /4" (44mm) SS200 2" (51mm) SS /4" (57mm) SS /2" (64mm) SS /4" (70mm) SS300 3" (76mm) Open Back Strike Specify Door Thickness Cylindrical Mortise Exit Device SB /4" (44mm) SB200 2" (51mm) SB /4" (57mm) SR118 Rabbeted front and strike Door Thickness - Mortise Specify D138 D134 D178 D200 D218 D214 Door Thickness 1-3/8" (35mm) 1-3/4" (44mm) 1-7/8" (48mm) 2" (51mm) 2-1/8" (54mm) 2-1/4" (57mm) Door Thickness - Cylindrical Specify std D214 Door Thickness - Exit Specify std D200 D214 Door Thickness 1-3/4" (44mm) to 2" (51mm) 2-1/8" (54mm) to 2-1/4" (57mm) Door Thickness 1-3/4" (44mm) 2" (51mm) 2-1/4" (57mm) Backset Specify Description Cylindrical Mortise Exit Device standard 2-3/4" (70mm) B /4" (95mm) B500 5" (127mm) Door Width Specify Description Cylindrical Mortise Exit Device W024 24" (610mm) standard 36" (914mm) std W048 48" (1219mm) 38

15 Functions ML20600 RNE1 Mortise Locks Outside Inside Series/Function Type Function Description ML20610 x TCRNE1 Fail Safe No Key Override No Deadbolt Entry Fail Safe - Power off unlocks outside trim Deadlocking latch Latch retracted by inside lever at all times Outside lever rigid except when valid user credential presented Request to exit and secure door position monitor are standard ML20603 x TCRNE1 Fail Safe With Key Override No Deadbolt Entry Fail Safe - Power off unlocks outside trim Deadlocking latch Latch retracted by inside lever at all times Outside lever rigid except when valid user credential presented Key outside retracts latch Request to exit and secure door position monitor are standard ML20660 x TCRNE1 Fail Safe No Key Override With Deadbolt Entry With Deadbolt Fail Safe - Power off unlocks outside trim Deadlocking latch Latch and deadbolt retracted by inside lever at all times Outside lever rigid except when valid user credential presented Turnpiece inside extends and retracts deadbolt Request to exit and secure door position monitor are standard ML20663 x TCRNE1 Fail Safe With Key Override With Deadbolt Entry With Deadbolt Fail Safe - Power off unlocks outside trim Deadlocking latch Latch and deadbolt retracted by inside lever and Deadbolt at all times Outside lever rigid except when valid user credential presented Key outside projects or retracts deadbolt and retracts latch Turnpiece inside extends and retracts deadbolt Request to exit and secure door position monitor are standard 4

16 Functions ML20600 RNE1 Mortise Locks Outside Inside Series/Function Type Function Description ML20630 x TCRNE1 Fail Secure No Key Override No Deadbolt Entry Fail Secure - Power off, trim outside is locked Deadlocking latch Latch retracted by inside lever at all times Outside lever rigid except when valid user credential presented Request to exit and secure door position monitor are standard ML20605 x TCRNE1 Fail Secure With Key Override No Deadbolt Entry Fail Secure - Power off, trim outside is locked Deadlocking latch Latch retracted by inside lever at all times Outside lever rigid except when valid user credential presented Key outside retracts latch Request to exit and secure door position monitor are standard ML20680 x TCRNE1 Fail Secure No Key Override With Deadbolt Entry With Deadbolt Fail Secure - Power off, trim outside is locked Deadlocking latch Latch and deadbolt retracted by inside lever at all times Outside lever rigid except when valid user credential presented Turnpiece inside extends and retracts deadbolt Request to exit and secure door position monitor are standard ML20685 x TCRNE1 Fail Secure With Key Override With Deadbolt Entry With Deadbolt Fail Secure - Power off, trim outside is locked Deadlocking latch Latch and deadbolt retracted by inside lever and Deadbolt at all times Outside lever rigid except when valid user credential presented Key outside projects or retracts deadbolt and retracts latch Turnpiece inside extends and retracts deadbolt Request to exit and secure door position monitor are standard 5

17 Available Trim Options ML20600 RNE1 Mortise Locksets Standard Lever A Rose B Rose F Rose Armstrong ASA ASB ASF Newport NSA NSB NSF Princeton PSA PSB PSF Citation CSA CSB CSF Dirke DSA DSB DSF Essex ESA ESB ESF Lustra LSA LSB LSF Regis RSA RSB RSF Armstrong Citation Dirke Essex* Lustra* Newport* Princeton* Regis Vineyard TM Frascati Merlot Tuscany Zinfandel G Rose FSG MSG TSG ZSG Muséo V Rose U Rose T Rose Y Rose X Rose W Rose Georgia V 101U 101T 101Y 101X 101W V 102U 102T 102Y 102X 102W V 103U 103T 103Y 103X 103W V 104U 104T 104Y 104X 104W V 124U 124T 124Y 124X 124W V 125U 125T 125Y 125X 125W salvador V 105U 105T 105Y 105X 105W V 106U 106T 106Y 106X 106W V 107U 107T 107Y 107X 107W V 108U 108T 108Y 108X 108W V 109U 109T 109Y 109X 109W V 110U 110T 110Y 110X 110W V 123U 123T 123Y 123X 123W marc V 111U 111T 111Y 111X 111W V 112U 112T 112Y 112X 112W V 113U 113T 113Y 113X 113W V 114U 114T 114Y 114X 114W V 115U 115T 115Y 115X 115W V 116U 116T 116Y 116X 116W V 130U 130T 130Y 130X 130W V 131U 131T 131Y 131X 131W V 132U 132T 132Y 132X 132W pablo V 117U 117T 117Y 117X 117W V 118U 118T 118Y 118X 118W V 126U 126T 126Y 126X 126W jackson V 119U 119T 119Y 119X 119W V 120U 120T 120Y 120X 120W V 121U 121T 121Y 121X 121W V 122U 122T 122Y 122X 122W V 127U 127T 127Y 127X 127W PIET 21L 21LV 21LU 21LT 21LY 21LX 21LW 21M 21MV 21MU 21MT 21MY 21MX 21MW 21S 21SV 21SU 21ST 21SY 21SX 21SW 21W 21WV 21WU 21WT 21WY 21WX 21WW 23M 23MV 23MU 23MT 23MY 23MX 23MW 25M 25MV 25MU 25MT 25MY 25MX 25MW Frascati Merlot Tuscany Zinfandel * 125* * * * * * * L 23M 127* 21M 25M 21S 21W *Complies with codes requiring lever to return to within 1/2" (13mm) of door face. 7

18 Available Trim Options ML20600 RNE1 Mortise Locksets Muséo Piet Lever Collection Trim and Finish Options Leather Insert Santoprene Insert Wood Insert Plain 21L 21S 21W 25M Trim Lever Finish Options Lever Style Shank Finish* Specify Insert Finish Specify Grip Finish** Specify 21L 629 or or 30 Black or Brown BK or BN 629 or or 30 21S 629 or or 30 Black BK 629 or or 30 21W 629 or or 30 Birch BH 629 or or 30 25M 629 or or 30 N/A or or 30 Polished with Satin Insert 21M With Raised Band 23M Trim Lever Style Shank Finish* Specify Lever Finish Options Insert Finish Specify Grip Finish Specify 21M M N/A * Rose and escutcheon finish is designated by shank finish selected ** Grip finish must match shank finish 8

19 2800ST Series Cam Action Door Closer OVERVIEW Features Smooth operation; efficient, powerful, heavy-duty Easier to open than rack-and-pinion door closers with track arms Slide track application with regular arm operating efficiency Slide track standard Adjustable spring size 1 through 6 Adjustable closing force Adjustable closing and latching speed Backcheck standard Non-handed Push or pull side installation Cast aluminum body Optional Feature Hold open DOOR SIZES Suitable for exterior and interior doors Recommended maximum interior door width 54" (137cm) Recommended maximum door weight 250 lbs. Standard opening range: - Push Side = Pull Side = 110 Note: Door openings greater than 110 can be achieved when an auxiliary door stop (by others) is used. Consult factory for details and templates. CERTIFICATIONS 10-year warranty (refer to current Norton price book for terms & conditions) Meets requirements for Americans with Disabilities Act (ADA) UL and UL10C listed ANSI/BHMA A156.4 certified 6/ ST - 3

20 2800ST Series Cam Action Door Closer STANDARD APPLICATIONS 2800ST HINGE (PULL) SIDE OF DOOR Maximum interior door width 54" (137cm). An auxiliary stop (by others) is suggested where severe conditions exist. 110 swing (trim permitting) Note: Door openings to 160 can be achieved if an auxiliary door stop (by others) is installed to dead stop the door. Consult factory for details. 1-1/2" 2" 3" 2-5/8" 2-5/8" NOTE: Contact factory for use on doors exceeding 250 lbs. PS2800ST STOP (PUSH) SIDE OF DOOR Minimum frame reveal is 1-1/2" (13mm). An auxiliary door stop is suggested when severe conditions exist. 110 swing (trim permitting) Note: Door openings up to 120 can be achieved if an auxiliary door stop (by others) is installed to dead stop the door. Consult factory for details. 1-1/2" 5-1/2" 2-5/8" 2-5/8" NOTE: Contact factory for use on doors exceeding 250 lbs. 2800ST /09

21 2800ST Series Cam Action Door Closer HOW TO ORDER No Prefix - Pull side installation PS - Push side installation H - Hold Open Prefix 2800ST x SUFFIX x FINISH Product Series FINISHES Product will be sprayed with a combination of waterborne acrylic and polyester powder coat. Description Specify Designation (BHMA) Complements the following finishes Old Designation Aluminum , 625, 629, 630, 651, 652 AL Statuary Bronze , 613 STAT Dull Bronze , 637, 639 DB Black Medium Amber Gold , 606, 632, 633 GB Prime Coat 600* SRI *600 is a special rust-inhibiting prime coat. Closers can be ordered prime coat only (specify closer x 600). An additional charge applies if finish coat is required over prime coat (ex: 2800ST x 600 x 689). 6/ ST - 5

22 2800ST Series Cam Action Door Closer PARTS LIST Track Assemblies Description Pull Side Push Side Arm Assembly Non-Hold Open 7701ST-1T 7701ST-5T Hold Open 7701ST-3T 7701ST-8T 2800ST-1A Spring Plate 1 Roll Pin 1 (2 Required) Buffer Spring 1 (2 Required) End Cap STEC (2 Required) Slide Track Assembly (See Chart) Arm Stud Clip 7700ASC Slide Assembly 7700SLD Roller Assembly* 1 Cushion Block 1 Stationary Block Assembly 1 * Hold Open Tracks Only 1 Part of Slide Track Assembly Screw Packs Closer Body Only SP2800B SP2800T SP2800S Closer Mounting Package Track Mounting Package Spline Kit Package 2800LAP (includes closer body screws only) Cover Package 2800P 2800ST /09

23 2800ST Series Cam Action Door Closer PARTS LIST Narrow Top Rail - #2888 Drop Plate: For use where the narrow top rail of the door prevents the closer from being mounted directly to the door surface. This drop plate must be used for closer mounted on a top rail between 1-7/8" and 3-3/8" (48mm and 86mm) in height. Retrofit Plate RP allows the 2800ST cam closer to replace the 4040 regular arm or parallel arm closers without modifying the existing hole patterns in the door. ARCHITECTURAL SPECIFICATIONS General Specifications Door Controls (interior) (exterior) swinging door(s) shall be cam and roller design contained within a precision cast aluminum housing. Door closing force shall be adjustable to ensure adequate closing control. Door closing speed shall be controlled by independent hydraulic adjustment valves in the sweep and latch range of the closing cycle. Door closer shall have an adjustable hydraulic backcheck valve to cushion the door speed if door is opened violently. Maximum door open shall be templated to (85 ), (90 ), (100 ), (110 ), conditions permitting. Door closer shall have hold open capability with an on/off selector and tension adjustment. Non-hold open units shall be U.L. Listed for self-closing door. Unit shall be in compliance with the requirements of the Americans With Disabilities Act (ADA). ANSI standards A Units shall meet C-UL US. 6/ ST - 7

24 Door Plates Mop Plate Kick Plate Stretcher Plate Up to 8"h x 48"w 6" to 12"h x 48"w 6" to 12"h and up to 48"w Width of Plates: Push Side: 2" less than door width. Pull Side: 1 1 2" less than door width. NFPA 80 STANDARDS Protection Plates: Factory-installed protection plates shall be installed in accordance with the listing of the door. Field-installed protection plates shall be labeled and installed in accordance with their listing. Exception: Labeling is not required where the top of the protection plate is not more than 16 in. (406 mm) above the bottom of the door. Armor Plate Up to 48"h x 48"w and available in most finishes Self-Drilling TEK Screws Cuts Door Plate Installation Time in Half Metal Door Plate - Economy Duty No. K1038 Material: Finishes: Fastener: Ordering: Weight: Options:.038" Thick Aluminum, Stainless Steel Brass Look Aluminum (BRS LK), US32D, US32DPAT, and US3LIFETIME #6 x 5 8 TH SMS Specify height x width x finish code. Add any options. 8" x 34" = 3.2 lbs. SA - self-adhesive mounting. TEK - self-drilling screws. Cutouts for locks, louvers, or windows. TORX - security torx screws. US32DPAT Patterned Stainless Steel Metal Door Plate - Standard Duty No. K1050, K1050F Material:.050" Thick Aluminum, Brass, Bronze, Stainless Steel Finishes: Available in standard architectural finishes, US32DBIO, US32D316, and US32316 (see page 7). Fastener: #6 x 5 8 TH SMS Ordering: Specify height x width x finish code. Add any options. Weight: 8" x 34" = 4.0 lbs. ANSI: J101 - metal armor plate, J102 - metal kick plate, J103 - metal stretcher & mop plate. Options: SA - self-adhesive mounting. TEK - self-drilling screws. Beveled 3 or 4 edges, specify B3E or B4E. CSK - countersunk holes. Cutouts for locks, louvers, or windows. TORX - security torx screws. Screw mounting (K1050F) and UL listed for use on 90-minute label wood doors and 3-hour label metal doors. 6/08 C1 Rockwood Manufacturing Company Phone:

25 dome stops Low Dome Stops No. 440, 441 Material: Solid cast brass with DuraFlex bumper. Finishes: Available in standard architectural finishes (see page 9). Other: Features: Options: No. 441 is packed with both WS and MS fasteners. For doors without thresholds (not undercut). Exterior pack screw packs, stainless steel plated to match use EXP suffix (440 x EXP) when ordering. No. Fastener Base Height Weight ANSI A #12 x 1 1 4" fh ws, plastic anchor 1 4" h x 1 7 8" dia " 2.1 lbs./10 L #12 x 1 1 2" fh ws, plastic anchor; #12-24 x 1" FH MS, lead anchor 1 4" h x 1 7 8" dia " 2.5 lbs./10 L02141 Dome Stop Combination Unit No. 441CU Material: Solid cast brass with DuraFlex bumper. Finishes: Available in standard architectural finishes (see page 9). Other: Features: Options: Set consists of 1 each No. 441 and 1 each No For use at doors with or without a threshold. Convertible for undercut or not undercut doors. Exterior pack screw packs, stainless steel plated to match use EXP suffix (441CU x EXP) when ordering. No. Fastener Base Height Weight ANSI A CU #12 x 1 1 2" fh ws, plastic anchor; #12-24 x 1 1 2" FH MS, lead anchor Dome stop: 1 4" h x 1 7 8" dia. Riser: 3 8" h x 2" dia " or 1 1 2" 3 lbs./10 L02141/ L Cast riser only 3 8" h x 1 7 8" dia. 3 8" 10 ozs./10 L02141 Cast Universal Dome Stop No. 441H Material: Solid cast brass with DuraFlex bumper. Finishes: Available in standard architectural finishes (see page 9). Features: Options: Low lip dome stop with height of high dome stop, eliminates the need to determine requirement for traditional low or high dome stop one stop for all applications. Integral cast pin for added strength. Universal screw pack included for all floor conditions. Exterior pack screw packs, stainless steel plated to match use EXP suffix (441H x EXP) when ordering. D4 No. Fastener Base Height Weight ANSI A H #12 x 1 1 4" FH WS, plastic anchor 7 32" h x 1 7 8" dia " 3.2 lbs./10 L02141 #12-24 x 1" FH MS, lead anchor L02161 Copyright 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.

26 Door Guard Protection Plates No. 605, 605SMS Door Guards & Silencers Material: Finishes: Features: Brass US3, US4, US5, US10, US10B, US26, US26D Protects corner of door from damage by door guard arm. No. Fastener Size Weight 605 self-adhesive tape 1 1 8" x 1" x 1 2" return 0.3 lbs./10 605SMS #6 x 5 8 FHSMS 1 1 8" x 1" x 1 2" return 0.3 lbs./10 Wall Guard No. 606 Material: Clear Rubber Other: Sold in sheets of 55. Features: Self-adhesive mounting. No. Fastener Size Weight 606 self-adhesive back 1" x 1" 0.4 lbs./55 Door Silencer No. 608CA Material: Clear Rubber Other: Sold in packages of 300. Features: Self-adhesive mounting. No. Fastener Size Weight 608CA 3 8" dia. x 1 8" metal or wood 0.2 lbs./ Door Silencers No. 608, 609 Material: DuraFlex Gray Rubber Other: Sold in packages of 100. ANSI No. Size Frame Type Weight A " dia. x 5 8" metal 1.3 lbs./500 L " x 3 4" wood 1.3 lbs./500 L03021 Revised 4/09 E9 Rockwood Manufacturing Company Phone: R

27 Transfer Device Solutions McKINNEY QC hinge transfers power from the power supply to the exit device electromechenical exit device with ElectroLynx 3" cable, minimum, needed between electromechanical exit and QC hinge Contents About ElectroLynx... 3 Transfer Device Decision Tree... 4 Hinge Wiring Requirement CORBIN RUSSWIN YALE SARGENT ElectroLynx Cables Special... 4 Standard McKINNEY Hinges, Concealed Circuit QC Hinge... 5 PoE Hinge Aluminum Continuous... 8 Stainless & Steel Continuous Door Cord and EPT... 9 Service Kit and Tools Standard Pinout Colors How ElectroLynx Helps To answer the demand for smart electronic access control and locking solutions that require fast, easy, and cost-effective installation, ASSA ABLOY Group brands use the ElectroLynx standardized plug-in connectors and color-coded wiring system. With ElectroLynx, doorway components come pre-wired for easy hookup to the power source. Key to the system is the transfer device hinge that carries power from the frame to the locking hardware. Overview: Makes it easy to bring power to the locking hardware Wires have connectors that snap together, like plugging a telephone into a jack Developed by ASSA ABLOY and rapidly becoming the industry standard Key Benefits of ElectroLynx Include: Fast, fool-proof, and future-proof installations Easy upgrades and retrofitting while maintaining fire rating Snap-together Molex connectors ensure proper connections No need to match up wires, create connections or drill holes in the door or frame Concealed wiring preserves aesthetics of the opening As part of their promise to provide innovative, fast and effective high security solutions to their customers, ASSA ABLOY Group companies offer ElectroLynx, a universal quick-connect system that simplifies the electrification of the door opening. ElectroLynx is a registered trademark of ASSA ABLOY Inc WIRE (9473)

28 Transfer Device Solutions Plug-and-Play 1 McKINNEY hinges and RIXSON pivots can have ElectroLynx connectors to transfer power from the incoming source through to the electrified hardware. The only hardwiring is from the building s wiring system to the opening All ElectroLynx retrofit cables are 12 conductor, supplied with an 8-pin connector and a 4-pin connector. If you are utilizing only 8-pin conductors or less, you can cut off the excess 4-pin conductor connectors. Pre-wired doors from CECO DOOR, CURRIES, BARON and GRAHAM have special harnesses built in to house the wiring components. 1 ElectroLynx is offered on the electrified hardware products of ADAMS RITE, CORBIN RUSSWIN, HES, RIXSON, SARGENT, SECURITRON and YALE 15'2" ElectroLynx cable from hinge location to ceiling Electric hinge or pivot bridges the power from the frame to the door In-the-door wiring harness brings power to the locking hardware or exit device Locking hardware or exit device comes pre-wired with connectors Pre-wired Doors The ElectroLynx system inside a door and frame includes a one-piece pre-fabricated wiring harness equipped with Molex connectors. The wiring harness consists of 8-pin and 4-pin ElectroLynx connectors with 22 gauge wire. It is an efficient labor-saving alternative to using conduit inside a door, which requires installation of wires at the job site. In addition to standard doors, fire rated doors from ASSA ABLOY companies - BARON, CECO DOOR, CURRIES and GRAHAM - are also available with ElectroLynx cabling WIRE (9473) 3

29 Transfer Device Solutions If you are not ordering ASSA ABLOY Door Group doors with the ElectroLynx cable pre-installed in the door, you must order an ElectroLynx retrofit cable to go between ANY hardware and the hinge. This includes 3" cables to go from the hinge to an exit device and up to a 15 cable to go up and around a full lite metal door. To ensure you order the correct ElectroLynx connecting cables, follow these steps: Are the doors preinstalled with ElectroLynx cables? YES You do not need to order a through-door cable Also order a 15' cable to go from the frame side hinge location, inside the wall up to the ceiling for termination NO Will the existing door accommodate a 5/8" chase or raceway to allow cable with Molex connectors be pulled through? Yes Example : - A hollow metal door with no obstructions or a 5/8" conduit or raceway No Examples : - Wood doors with a 3/8" raceway - Hollow metal doors with steel stiffeners YES NO Order cable with Molex connectors on both ends, illustrated below Order cable with one end with Molex connectors, and one end pinned, illustrated below What length of retrofit cable should you order? From the examples below, measure from the hinge location to the hardware location. * Add 2" to the length - Hollow metal door with full lite glass kits Door with 3 hinges Door with 4 hinges Door with full lite or steel-stiffened hollow metal Exit device with 3 hinges Exit device with 4 hinges Standard ElectroLynx Retrofit Cable Sizes Actual Cable Length 12 Conductor and Molex both ends 12 Conductor and Molex one end, pinned one end Typical Application 3" QC-C003 QC-C003P 6" QC-C006 QC-C006P Between hinge and the end of an exit device. 12" QC-C012 QC-C012P 26" QC-C200 QC-C200P 32" QC-C206 QC-C206P 38" QC-C300 QC-C300P Between hinge and through the door to the lockset or exit device trim. 44" QC-C306 QC-C306P 50" QC-C400 QC-C400P 15' 2" QC-C1500 QC-C1500P From the hinge location, up the jamb to above the ceiling, or up and around full lite or half lite metal door WIRE (9473)

30 Transfer Device Solutions McKINNEY QC Concealed Circuit Electric Hinges The McKINNEY ElectroLynx hinge is an intermediate connector that passes a constant flow of current between the source of power (jamb) and the actuated devices in the door (electric locks, exit devices, etc.) regardless of door position. Each hinge features concealed plug connectors that eliminate the need for separate or exposed wiring. Brass eyelets add protection and durability to the ElectroLynx hinge and common wire colors and standard connectors make installation quick and simple. Once installed, it will give no outward indication of its function and will transmit power efficiently and reliably, as long as the wire capacity is not exceeded. All ElectroLynx hinges are factory tested and specially packaged to minimize against damage during shipment. Installation instructions are packed with each hinge. 28 Gauge multi-strand wires are used. A 6" pigtail is provided for connection to the source wiring, and additional 6" pigtails may be requested. The wire colors are with the electromechanical hardware of other ASSA ABLOY brands. An 8 position connector is used for QC2, QC4 QC6 and QC8 wire hinges An 8 position and 4 position connector is used for QC12 wire hinges QC2, 4 or 6 hinges are available for special applications, but are not used with the decision tree found on page 4 Please call WIRE (9473) if you are in doubt regarding hinge requirements. Available up to 12 wires Rated 4 amp 24 volts AC or DC, 16 amp pulse for 300 milliseconds (cycle time not less than 5 seconds), 10 amp pulse for 250 milliseconds (cycle time not less than 5 seconds) Optional MG-16 mortar guard available (mortar guard required on steel frames) Steel and Stainless Steel QC hinges are UL listed for use up to and including 3 hour rated openings QC2 wire hinges provided with 8 position connector for new construction, specify QC2 * Consult customer service for availability How to order string 4½X4½ TA D QC12 Pigtail assembly 3- Knuckle 5- Knuckle TA314 TA714 TA386 TA786 Male connector TA2314 T4A3386 T4A3786 TA2895 T4A3395 T4A3795 QC12 Back of 12 wire hinge shown Full Mortise QC hinges are available in most BHMA and McKINNEY powder coat finishes Female connector WIRE (9473) 5

31 Transfer Device Solutions McKINNEY ElectroLynx Power over Ethernet (PoE) Hinge The McKINNEY ElectroLynx PoE, the next phase of Quick Connect hinge products by McKINNEY, provides for the passing of Ethernet data through the door opening. Installation is a snap with the friendly plug and play connectors which allow power to be linked from the incoming source through the door to the electrified hardware. PoE data is bidirectional. Brass eyelets add protection and durability to the PoE hinge which features common wire colors coordinated to work with intelligent Power over Ethernet electromechanical hardware from SARGENT and Corbin Russwin. The PoE hinge should be installed in the second from bottom hinge position on the door. Once installed, it will give no outward indication of its function and will transfer power and data efficiently and reliably, as long as the wire capacity is not exceeded. All PoE hinges are factory tested and specially packaged to minimize damage during shipment. Installation instructions are packed with each hinge. Along with the PoE hinge, mating PoE door and frame side harnesses are required, to complete the opening. The required PoE harnesses must be ordered separately (see below for detail). Specify suffix PoE. Consult factory for the availability of additional finishes and hinge types. Patent Pending Power over Ethernet Hinge Features Each hinge features two 6-position and two 4-position Molex connectors, 9 multistrand wires; 2 twisted pairs (26 AWG), 4 straight conductors (28 gauge) and 1 straight conductor (22 AWG) with concealed plug connectors that eliminate the need for separate or exposed wiring. Rated 350 ma 48 volts DC nominal, the hinge is capable of two PoE wiring configurations: 1. Power over Data (5 wire); Power and Data supplied together over the 2 twisted (26 AWG) pairs and the 22 AWG conductor is used for the earth ground connection. 2. Data with Power over spares (9 wire); Data over 2 twisted (26 AWG) pairs with Power over spare pairs (4 straight 28 AWG conductors) and the 22 Awg conductor is used for the earth ground connection. McKINNEY CATALOG # Description: 4.5 x 4.5 TA D PoE Standard Weight 5 Knuckle 4.5 x 4.5 T4A D PoE Heavy Weight 5 Knuckle Standard ElectroLynx Power over Ethernet (PoE) Harnesses Harness Length McKINNEY Catalog # Door Side Application 30" PoE-C206P 20" to 25" door width (doors with 3 butt hinges with PoE hinge in center to stile to stile raceway to lock prep). 36" PoE-C300P 26" to 31" door width (doors with 3 butt hinges with PoE hinge in center to stile to stile raceway to lock prep). 42" PoE-C306P 32" to 36" door width (doors with 3 butt hinges with PoE hinge in center to stile to stile raceway to lock prep). 48" PoE-C400P 37" to 42" door width (doors with 3 butt hinges with PoE hinge in center to stile to stile raceway to lock prep). 54" PoE-C406P 43" to 48" door width (doors with 3 butt hinges with PoE hinge in center to stile to stile raceway to lock prep). Frame Side Application 180" PoE-C1500P From the hinge location, up the jamb to wall/ceiling NOTES: The PoE door & frame harnesses can accommodate a variety of new (with raceway) and retrofit applications. Connectors are small enough to run through a 3/8" (min.) stile-to-stile door raceway. Connects to intelligent Power over Ethernet electromechanical hardware from Sargent and Corbin Russwin WIRE (9473)

32 Transfer Device Solutions Hinge Wiring Requirements CORBIN RUSSWIN Hinge YALE Hinge Access Control Products - All Device Types Access Control Products - All Device Types Access 600 Series RNE1 QC12 Symphony Series QC12 Access 800 Series NE1 QC8 eboss Series (Hard Powered) QC8 Access 800 Series AC2 (Hard Powered) QC8 Cylindrical Locksets 5400LN / 5300LN Series Cylindrical Locksets CL3300 Series All Functions / Options QC8 All Functions QC8 Mortise Locksets 8800 Series Mortise Locksets ML20900 Series All Functions / Options (Exception LBM, DBM) QC8 All Functions / Options QC8 LBM (Latchbolt Monitor) QC12 Electrified Exit Devices ED5000 / ED4000 DBM (Deadbolt Monitor) QC12 All Functions / Options (Exception M93, M61) QC8 Electrified Exit Devices 7000 Series M93 (Latch Bolt Monitor) Alone or in combination with any other option M61 (Alarmed Exit with M35 Hardwired Option) QC12 QC12 All Functions / Options (Exception O, A) O (Latch Bolt Monitor) Alone or in combination with any other option QC8 QC12 Electrified Exit Trim 9900 Series A (Alarmed Exit with HW Hardwired Option) QC12 All functions / Options QC8 Electrified Exit Trim 600 Series All functions / Options QC8 SARGENT Hinge Access Control Products - All Device Types Harmony Series QC12 Profile Series v.n1 QC8 Profile Series v.g1.5 (Hard Powered) QC8 Cylindrical Locksets 10 Line / 8 Line All Functions / Options QC8 Mortise Locksets 8200 Series All Functions / Options (Exception LX, DX) QC8 LX (Latchbolt Monitor) QC12 DX (Deadbolt Monitor) QC12 Electrified Exit Devices 80 Series All Functions / Options (Exception 56-, TL-, 59-, AL-) QC8 56- (Electronic Latch Retraction) Timer Function Only QC12 TL- (Electro-Luminescent) QC (Electroguard Delayed Egress) Remote Alarm, Latchbolt Mon. QC12 AL- (Alarmed Exit with 546 Harness - Hardwired Option) QC12 Electrified Exit Trim 700 Series All functions / Options QC8 Electrified Exit Devices AND Electrified Trim Combination All Options with All Trim (Exception 56-, TL-, 59-, AL-, 54-) QC (Electronic Latch Retraction) Timer Function Unavailable QC12 TL- (Electro-Luminescent) Unavailable QC (Electroguard Delayed Egress) Remote Alarm, Latchbolt QC12 Unavailable AL- (Alarmed Exit) Remote Reset and Door Position inputs QC12 Unavailable 54- (Trim Monitor Switch) Normally Closed Switch option QC12 Unavailable WIRE (9473) 7

33 Transfer Device Solutions McKINNEY Aluminum Continuous Electrified Hinges The McKINNEY electrified continuous hinge is furnished with bonded, 4-conductor flat cable with connectors at each leaf. Two options allow variable degrees of service to be performed at the specific location of current carrying cables via either a removable 8" or a pivoting 8" section of the hinge. Both of these options, SER and ACC are available as 4, 8 or 12 wire configurations on our Full Mortise Aluminum Continuous Hinges. Serviceable/Removable (SER) - The hinge is furnished to be installed in three sections, allowing the current carrying cables to be serviced or replaced without removing the door from the frame. Additionally the SER option allows the current carrying cables to be safely stored or delivered to the electrician or security contractor prior to the installation of the electrified hardware, eliminating the necessity of the electrician or security contractor being present when the doors are being hung. Available on full mortise aluminum continuous hinges Each electrical prep is supplied with a 48" and 96" wire harness ElectroLynx HC-6/4 or HC-6/8 pigtails are included in pack for installation with other ASSA ABLOY ElectroLynx products Electrical modification meets new SDI location at center of hinge Standardized prep locations on 83", 85", 95" and 120" hinges Accessible (ACC) The hinges are furnished to be installed in a single section with each leaf modified to pivot at the location of the current carrying cables and allow access to the cables and connected wiring. Electrical modification is in the center of the hinge. Features: Performance tested 1,250,000 cycles with the 4-conductor flat cable Each 4-conductor cable carries 4 24volts with a 16 amp inrush current for 300 milliseconds Each hinge is provided with a 4 amp in-line fuse to protect the cable from any overload or surge in power Flat cable conductor is warranted for 5 years Hinges are handed Serviceable SER option shown McKINNEY Stainless Steel Pin & Barrel Continuous Electrified Hinges Features: The McKINNEY EL option is available on FM300, FM3500 and FM3700 edge mount hinges (not available on raised barrel applications) 14 Gauge, type 304 stainless steel, features.25 diameter stainless pin Symmetrically templated hole pattern FM300 & FM3700 Supports weight up to 600 lbs.; FM3500 supports up to 900 lbs. (maximum 4'0" door width) Hinges are handed Optional ETAP electrical transfer prep available Available in 4, 8 or 12 wire configurations EL Concealed Current Transfer (Standard Prep Locations) For McK-FM300, McK-FM3500, McK-FM3700 EL-4 Qty (4) 28 Gauge Wires EL-8 Qty (8) 28 Gauge Wires EL-12 Qty (12) 28 Gauge Wires WIRE (9473)

34 Transfer Device Solutions Door Cord and Electrical Transfer (EPT) McK-EPT Electrical Power Transfer Installs in the door and frame edges Accepts a thick cable and protects it within a flexible steel shield Device that will work on most doors hung using butt hinges, continuous hinges or pivots Will not function on a center pivot door How to Order Part Number McK-EPT McK-EPTL McK-EL-EPT McK-EL-EPTL Description Electrical power transfer Electrical power transfer, long ElectroLynx EPT -12 wire ElectroLynx EPTL -12 wire EPT can be ordered with ElectroLynx by specifying McK-EL-EPT or McK-EL-EPTL. McK-TSB-C Door Cord Simplest and most economical solution for power transfer Consists of an 18" or 36" armored stainless steel cable and plastic end pieces in light gray and black Cable has an interior diameter of.25" Supports interior wire cables up to.2" How to Order Part Number McK-TSB-C McK-TSB-CXL Description Door cord with gray/black caps 18" cord Door cord with gray/black caps 36" cord WIRE (9473) 9

35 Transfer Device Solutions Service Kit and Tools QC-R001 Service Kit The service kit includes a quantity of every different type of connector and terminal required for repairing product connections/ terminations or pinning wires on certain retrofit harnesses. Contains 10 each 2, 4, 8 molex receptacles and plugs as well as corresponding terminals, extraction tool and pinning assembly guide. Female receptacle (8 circuit) Locking mechanism Male plug (8 circuit) Miscellaneous Parts Part Number Description 1 bag (100 pc) QC-RF2 Female receptacle (2ckt) 1 bag (100 pc) QC-RF4 Female receptacle (4ckt) 1 bag (100 pc) QC-RF8 Female receptacle (8ckt) 1 bag (100 pc) QC-RM2 Male plug (2ckt) 1 bag (100 pc) QC-RM4 Male plug (4ckt) 1 bag (100 pc) QC-RM8 Male plug (8ckt) 1 bag (100 pc) QC-FT2024 Female terminal (AWG 20-24) 1 bag (100 pc) QC-FT2630 Female terminal (AWG 26-30) 1 bag (100 pc) QC-MT2024 Male terminal (AWG 20-24) Female receptacle requires female terminal Male plug requires male terminal 1 bag (100 pc) QC-MT2630 Male terminal (AWG 26-30) 1 bag (10 pc) QC-DCC Pinning assembly guide QC-R003 Molex Hand Crimp Tool The crimp tool is required for adding Molex terminals (connector pins) to wires used with ElectroLynx products. The tool is intended for low volume, or repair requirements only. The plug and receptacle connectors are designed to mate and lock together as shown in the figure. Plug the connectors onto each other with the locking mechanism aligned as indicated. QC-DCC Pinning Assembly Guide Included with every pinned conductor to aid in wire assembly. QC-R002 Extraction Tool The extraction tool is a simple hand tool used to remove damaged terminals from an ElectroLynx female receptacle or male plug WIRE (9473)