SLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation.

Size: px
Start display at page:

Download "SLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation."

Transcription

1 SLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation.) NOTE: The Ultra has proven to exhibit distinct personalities from one sled to another. Ultra tuning does not follow the same rules we re accustomed to. Slight variations in clutching, carburetion, RPM or gearing can result in major performance losses. Please follow the instructions carefully. NOTE: Due to the large diameter of this pipe set, some slight hood and bellypan modifications are necessary for correct installation. Modifications include: removal or modification of screen kit, removal of two screen kit mount tabs on bottom of center louvers (see illustration 9). Bellypan outlet: Replacement, (included in kit) and trim plastic to allow for larger outlet. 1. Remove stock exhaust, Y-pipe and outside rear muffler support. Disconnect silencer EGT probe from white/yellow and white/red wires. This EGT probe and the computer box it is connected to is a backfire safety devise for the stock silencer; it is not required for the SLP pipe set. To disable the computer, disconnect the yellow wire and the black wire leading from the computer to the three-pin plug. Do not unplug the yellow wire leading to the voltage regulator.(see ILL.# 1A) NOTE: Engine will not run properly until computer is disabled. 2. Install three exhaust flanges included with pipe set and OEM exhaust gaskets on to cylinders. (All three flanges are the same, when properly installed, flanges should have a downward angle). 3. Shock tower heat tape installation: Supplied in parts kit are eight pieces of 1 ½ x 7" tape. Place tape as shown in illustration 1. NOTE: For best tape adhesion, all surfaces must be free from dirt and oil. 4. Install mag (right) side suspension tower heat shield (small formed steel plate). Position this plate on forward edge of suspension tower 3 3/4" (see illustration 2, line C) inward from outer forward edge of suspension tower. Mark and drill 3/16" holes and fasten into place with longer small head rivets and washers provided. 5. With notched end pointing to the left, position PTO (left) side heat shield to butt up to highest portion of shock tower (see illustration 3). Mark and drill 3/16" holes. Rivet in place with longer small-head rivets. RMK models: See illustration 3 for proper heat shield location. Starting Line Products, 743 Iona Road, Idaho Falls, ID (208) Fax: (208) ; 1

2 6. Installation of lower mag side heat shield (8"x7 ½ square aluminum plate): Position heat shield in bottom of belly pan on right side with the line of three holes pointing up toward the nose cone plate (see ILL 4). Slide heat shield between nose cone plate and belly pan, line up three holes in heat shield with holes in nose cone plate, rivet in place with short aluminum rivets provided. Using single hole at the bottom of heat shield as a guide, drill 3/16" hole in belly pan and rivet in place. (Insert this rivet from the outside of belly pan). 7. Exhaust outlet installation: Drill out rivets and remove OEM outlet plate. Remove and cut out template located in back of instruction sheet. Line up right front rivet hole in belly pan with rivet reference mark on template. Line right edge of template with the right edge of belly pan. Tape template securely in place. Using template as a guide, enlarge outlet hole in belly pan to match template. Insert SLP outlet plate into belly pan hole (spring hook forward) insert one large head rivet into right front hole in belly pan. Using plate as a guide, drill out the three remaining holes and rivet into place using large head steel rivets. NOTE: Before drilling holes, make sure right side of outlet plate is parallel with right edge of belly pan. NOTE: RMK models will have 1/4" bolts in place of rivets in the two front OEM outlet plate holes. The template positioning will be the same as stated above. 8. Remove bolt connecting steering drag link to bellcrank. Replace OEM bolt with shorter 1 ½ x3/8" bolt and shorter lock nut provided. Make sure bolt is installed head down. Torque to 25 ft. lbs. RMK models: Replace OEM bolt with allen head bolt provided in kit, install with bolt head up, torque to 25 ft. lbs. 9. Wire loom and speedometer cable location: Remove OEM aluminum loom/cable support located at base of windshield. Route wire loom and speedo cable as shown in ILL 5, rivet OEM loom/cable support (removed from hood) to secure wire loom to left shock tower as shown in illustration. Replace OEM loom/cable support with plastic tie provided. Secure loom/cable to hood at base of windshield with plastic tie to rubber o-ring securing windshield. NOTE: Cover wire loom with reflective heat tape provided in area s closest to pipe. 10. Spring clip installation: Remove top rear chain case cover bolt. Install spring clip torque bolt to 8 ft lbs. NOTE: Small end of spring clip should point to the rear. 11. Pipe installation: Head pipes are marked to identify location. Install mag (right) pipe first (marked M), center pipe second (marked C), PTO (left) pipe third (marked P). NOTE: The center pipe is a tight fit. It may be necessary to set the mag pipe in place, slightly to the right of flange. Install center pipe then connect mag pipe to cylinder flange. 2

3 12. Place OEM rubber anti-vibration insulator into mount on silencer (see illustration 6) and install silencer (see illustration 7) when installing silencer into belly pan outlet plate, apply silicone to edge of silencer outlet stops as shown in illustration 8. NOTE: Make sure cylinder flange rings do not bind when installing pipes. Place ring end gaps 180 degrees from each other. For best seal apply silicone sealer (Permatex #27 B or equivalent) to all joints including silencer outlet to belly pan outlet plate connection. NOTE: If you fail to seal all voids between the silencer outlet and the belly pan outlet, exhaust gases will be forced past the pipe into the engine compartment. Symptoms are similar to an extremely over-rich condition causing fouled spark plugs and severe engine bogging, especially when riding in deep powder at slow speeds. 13. Spring installation: Seven short and three long springs are supplied with kit. Six short springs connect cylinder flanges to pipes, use three OEM springs for pipe to silencer connections. One long spring hooks to front of center pipe and connects to the obround hole in aluminum nose plate. Second long spring connects the center head pipe to PTO pipe middle cone section. Third long spring connects rear of silencer to spring clip on chain case. The final spring connects from front of silencer outlet to outlet plate. NOTE: Make sure the spring connecting the pipe to the aluminum nose plate is correctly installed. Without this spring in place, pipes can wear on each other and even crack. 14. Relocate right-hand hood cable mount inboard 6 inches for proper cable length. Connect hood cable to hook on center pipe. (See Illustration 10). LUBRICATION OIL INJECTION ADJUSTMENT:Set at factory recommended setting. OIL RECOMMENDATIONS: For high performance trail applications use SLP brand XPT oil. CARBUETOR TUNING IMPORTANT NOTE: Carb tuning specifications included in this section are a base line and should be adjusted as needed for your particular atmosphere. Use exhaust gas temperature gauges or monitoring plug and piston color for tuning guide. IMPORTANT NOTE: Due to quality variance in present day fuels, SLP recommends unleaded premium for all snowmobiles with 92 or better octane. Fuels containing alcohol or clean air additives will require larger main jets, usually two sizes more than the SLP jetting chart. Jet needle must be raised one E clip position. 3

4 For Ultra 680 stock engine with pipe set #09-680, air box in place, remove the two inlet rubber tubes from top inlet of air box (leave three rubber tubes in bottom of air box). Do not alter air box in any other manner. Foam inlet filters should be glued into original position. A ltitu d e M eters (F eet) (0-3000) (3-6000) (6-9000) ( ) Tem p eratu re -20 & B elow -20 to to & A bove P TO 410 C enter 390 M ag 410 P TO 370 C enter 350 M ag 370 P TO 350 C enter 320 M ag 350 P TO 340 C enter 310 M ag 340 P TO 400 C enter 380 M ag 400 P TO 360 C enter 340 M ag 360 P TO 340 C enter 310 M ag 340 P TO 330 C enter 300 M ag 330 P TO 390 C enter 370 M ag 390 P TO 350 C enter 330 M ag 350 P TO 330 C enter 300 M ag 330 P TO 320 C enter 290 M ag 320 P TO 380 C enter 360 M ag 380 P TO 340 C enter 320 M ag 340 P TO 320 C enter 290 M ag 320 P TO 310 C enter 280 M ag 310 Altitude & higher Pilot Needle SLP SLP SLP Needle Jet 247-P P8 247-P4 Air Screw ¼-½ turn 1 turn 1 turn Elevation: 0-3,000 ft. Clutch Tuning Primary Spring - Blue, Polaris part # Primary Weight - 10 A, Polaris part # , 55 gram Secondary Spring - Blue, Polaris part # , or SLP part # Blue Stripe #2 Preload (# 3 preload for heavy snow conditions) Helix - Progressive, 42-34, SLP part # 40-42/34 Elevation: 3-6,000 ft. Primary Spring - Blue, Polaris part # * Primary Weight - 10 AL, Polaris part # , 53 gram Secondary Spring - Blue, Polaris part # , or SLP part # 40-42, Blue Stripe Helix - Progressive 42-34, SLP part # 40-42/34 # 2 Preload (# 3 preload for heavy snow conditions) Elevation: 6,000 & Higher Primary Spring - Black/Red, SLP part # (best) (Second choice - Blue, Polaris part # ) * Primary Weight - "10", Polaris part # (51 gram) Secondary Spring - Blue, Polaris part # , or SLP part # 40-42, Blue Stripe Helix - Progressive, 42-34, SLP part # 40-42/34 # 2 Preload (# 3 preload for heavy snow conditions) 4

5 Running RPM For Racing Specifications: Call SLP Tech. Line # IMPORTANT NOTES: Failure to perform the following adjustments could cause loss of performance and boggy low end power. 1. Belt side clearance. Be sure belt side clearance on drive clutch is not excessive. Recommended.010" to.030" between belt and clutch face. Re-shim spider if needed. Excessive clearance may cause a low end bog. 2. Type of belt. Use only SLP approved performance belts or stock Polaris brand belts. 3. Tuning variable. Due to riders weight and conditions the sled is used in, heavier or lighter clutch weights and /or springs may have to be used to achieve proper running RPM. 4. Belt free play. Proper belt free play is very important for best performance. Driven shims can be added or subtracted (or cam adjustment on later models) to adjust belt as tight as possible without creeping at an idle. 5. RMK models are geared too low (20/39 std.) for most applications. We recommend gearing up to 20/37 or 20/35. Gearing Recommendations NOTE: This pipe set is designed to peak at about the same RPM as the stock Ultra. The RMK Ultra is geared for clutch lock-up at about 80 mph. Since SLP pipes are designed to peak at about the same RPM as the stock Ultra, high speed performance will not be realized unless gearing is increased. Changing to smaller axle drivers will also reduce the gear ratio and should be compensated for with an increase in sprocket ratio ' 23/ ' 21/ ' & Above 20/35 5

6 For 1996 Ultra 680 With SLP # Pipe Set Note: Due to present day fuels and the dramatic horsepower increase with SLP pipes, the following must be adhered to for the best performance and reliability. A. Ignition System Condition: It has been noted that on some Ultra models high RPM timing is advanced more than our recommendations. If this condition exists, piston damage can occur even with rich jetting. The following information is mandatory for proper performance and dependability. Note: Timing at low RPM will vary from one sled to another when high RPM timing is correct. This will not cause any problems as long as timing at 3500 RPM does not exceed 26º. 1. Timing Specifications: To control midrange and top end, timing must be set at 8000 RPM. Low Elevation High Elevation 12º at 8000 RPM 14º at 8000 RPM 12º =.893mm or.035 BTDC 14º = 1.213mm or.048" BTDC Timing variance ± ½º 2. Spark Plugs: a. Average Trail Riding: NGK BR9ES b. Lake Racing, High Speed Use: NGK BR10ES 6

7 B. Fuel System Requirements 1. Fuel Shut-Off Valve: It has been noted that this valve requires special attention when moving lever to ensure that it is fully open. It has also been noted that the fuel valve can vibrate or accidently be moved from its open position and restrict fuel flow. Fuel lines or tank vent line, if pinched or kinked, can also reduce fuel flow. Fuel flow restriction can cause piston damage or failure. 2. Fuel Octane Requirements: a. Minimum 92 octane b. RMK Model: If used under 6,000 ft. altitude, use race fuel (100 octane or better.) 3. Oxygenated Fuels: Fuels containing clean air additives, MTBE, Ethanol, Methanol, or similar materials these fuels require additional jet size and are more prone to detonation, especially on long runs at one throttle position. Increase main jet by two sizes if using these fuels C. Cylinder Head Modification: Note: Higher-than-factory-recommended compression will reduce performance and reliability. 1. Low Altitude (0 ft. to 6,000 ft.): a. SP and SKS models, DO NOT mill heads for higher compression. Even minimal milling will require use of much higher fuel octane and/or richer fuel mixture. For pump fuel, stock heads are best. b. RMK model, DO NOT mill heads. Minimum of 100 octane race gas is necessary for under 6,000 ft. altitude for stock heads. 2. High Altitude (6,000 ft. and higher): a. SP and SKS models may use RMK heads for high altitude with 92 octane fuel. Machining of SKS and SP heads to duplicate the RMK heads for high altitude use is OK, but do not mill more than.015" from head surface. For more performance and reliability, use SLP Power Dome Heads. 7

8 Illustrations Illustration 1 Yellow Wire Rear of Sled Voltage Regulator Do Not Disconnect Yellow Yellow (Center) Disconnect Black (Toward Front of sled) Disconnect Red/White Yellow/White Disconnect Probe Illustration 1A 8

9 Illustrations Line C Illustration 2 = 1 7/16 Illustration 3 9

10 Illustrations Illustration 4 Illustration 5 10

11 Illustrations Illustration 6 Illustration 7 SILICONE Seal all open areas between silencer and belly pan plate. Illustration 8 11

12 Illustrations Cut Cut Illustration 9 6 Illustration 10 12

13 For 1997 Ultra SP Only 6 Place heat shield on left side shock tower as shown in illustration. Using heat shield as a pattern, drill two 3/16 holes in shock tower and fasten in place with provided rivets and backing washers. 13

14 CUT LINE RIGHT SIDE Illustrations Outlet Plate Template CUT LINE REFERENCE HOLE CUT LINE 14

15

SLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation.

SLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation. SLP PIPE INSTALLATION INSTRUCTIONS POLARIS 1996-97 ULTRA 680 SP SKS & RMK P.N. 09-6802 (Read instructions carefully before installation.) NOTE: The Ultra has proven to exhibit distinct personalities from

More information

XLT SPECIAL TRIPLE PIPE SET P.N Installation Instructions

XLT SPECIAL TRIPLE PIPE SET P.N Installation Instructions 1995-97 XLT SPECIAL TRIPLE PIPE SET P.N. 09-598 Installation Instructions Revised 8/20/02 Read instructions carefully before installation 1 - Remove stock exhaust, Y-Pipe, front and rear muffler support.

More information

XCR 600/ XLT TRIPLE PIPE SET P.N Installation Instructions

XCR 600/ XLT TRIPLE PIPE SET P.N Installation Instructions 1994-97 XCR 600/1993-97 XLT TRIPLE PIPE SET P.N. 09-5970 Installation Instructions Read instructions carefully before installation 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three

More information

POLARIS XLT-SPECIAL TRIPLE PIPE SET P.N

POLARIS XLT-SPECIAL TRIPLE PIPE SET P.N 1998-99 POLARIS XLT-SPECIAL TRIPLE PIPE SET P.N. 09-596 Important: Read instructions carefully before installation. 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three exhaust flanges,

More information

POLARIS XLT 580/600 INSTALLATION INSTRUCTIONS PART # READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET

POLARIS XLT 580/600 INSTALLATION INSTRUCTIONS PART # READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET Page 1 of 6 POLARIS 1993-97 XLT 580/600 INSTALLATION INSTRUCTIONS PART #09-595 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET 1. Remove stock exhaust, y-pipe, front and rear muffler

More information

POLARIS 700 XC/SKS/RMK SLP TWIN PIPE SET P.N

POLARIS 700 XC/SKS/RMK SLP TWIN PIPE SET P.N POLARIS 700 XC/SKS/RMK SLP TWIN PIPE SET P.N. 09-710 IMPORTANT: Read instruction carefully before installation. For engines with stock porting use either 09-700 glass pack pipe set or 09-710 canister pipe

More information

SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & # & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92

SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & # & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92 Page 1 of 5 SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & #09-10 1988 & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET #09-9 (For stock

More information

POLARIS Twin 600/700 SINGLE PIPE SET P.N

POLARIS Twin 600/700 SINGLE PIPE SET P.N 1997-1998 POLARIS Twin 600/700 SINGLE PIPE SET P.N. 09-718 Important: Read instruction carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been placed

More information

Single Pipe Set with OEM Silencer for /800 RMK/XC, /800 SKS, /800 Switchback and Switchback

Single Pipe Set with OEM Silencer for /800 RMK/XC, /800 SKS, /800 Switchback and Switchback Single Pipe Set with OEM Silencer for 2002-05 700/800 RMK/XC, 2003 700/800 SKS, 2004 700/800 Switchback and 2005 800 Switchback P.N. 09-836 Important: Read instructions carefully before installation. Note:

More information

SLP Twin Pipes for 2004 Arctic Cat 900 Mountain Cat Twin P.N (CP)

SLP Twin Pipes for 2004 Arctic Cat 900 Mountain Cat Twin P.N (CP) Setting the World s Performance Standards Twin Pipes for 2004 Arctic Cat 900 Mountain Cat Twin P.N. 09-907(CP) Contents of Pipe Set 1 - Plastic Zip tie 3 - Large Head Rivets 4 - Short s 1 - Red Silicone

More information

Sinlge Pipe for /800 Pro-X/Pro-X2/Pro-XR P.N

Sinlge Pipe for /800 Pro-X/Pro-X2/Pro-XR P.N Sinlge Pipe for 2003-04 700/800 Pro-X/Pro-X2/Pro-XR P.N. 09-9 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been

More information

POLARIS 700/800 PRO X SINGLE PIPE P.N

POLARIS 700/800 PRO X SINGLE PIPE P.N 2003-04 POLARIS 700/800 PRO X SINGLE PIPE P.N. 09-839 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been placed there

More information

SLP Twin Pipes for 2003 Arctic Cat 900 Twin

SLP Twin Pipes for 2003 Arctic Cat 900 Twin Setting the World s Performance Standards SLP Twin Pipes for 2003 Arctic Cat 900 Twin P.N. 09-902(CP) and 09-903(CP) IMPORTANT: Read instructions carefully before installation. 1. Remove stock exhaust,

More information

1-Remove stock exhaust, Y-Pipe, and silencer (Retain OEM springs and exhaust gaskets for pipe installation).

1-Remove stock exhaust, Y-Pipe, and silencer (Retain OEM springs and exhaust gaskets for pipe installation). Single Pipe Set for use with Performance Edition Kit for 2003-04 POLARIS 800 Pro X P.N. 09-848 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid

More information

Single Pipe Set for Big Block: /700 XC/SKS/RMK and /700 RMK/SKS For use with Stock Silencer P.N

Single Pipe Set for Big Block: /700 XC/SKS/RMK and /700 RMK/SKS For use with Stock Silencer P.N Single Pipe Set for Big Block: 2000 600/700 XC/SKS/RMK and 2001 600/700 RMK/SKS For use with Stock Silencer P.N. 09-732 Important: Read instruction carefully before installation. Note: Removal of pipe

More information

SLP Single Pipe for Polaris 600 H.O. Fusion/RMK/Switchback/Shift (Carb Models)

SLP Single Pipe for Polaris 600 H.O. Fusion/RMK/Switchback/Shift (Carb Models) SLP Single Pipe for 2006-09 Polaris 600 H.O. Fusion/RMK/Switchback/Shift (Carb Models) Part # 09-634 Kit Contents: 2-7 Insulated Heat Tape 1-1/8 Pipe Adjustment Washer 4-30 Reflective Heat Tape 1 - Wire

More information

SLP PART # ATTENTION DEALER

SLP PART # ATTENTION DEALER PART #09-8000 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following: The

More information

SLP Single Pipe Set for Arctic Cat 900 Mountain Cat Carb and EFI with Transfer Outlet Tube P.N CP/09-914CP

SLP Single Pipe Set for Arctic Cat 900 Mountain Cat Carb and EFI with Transfer Outlet Tube P.N CP/09-914CP Setting the Wld s Perfmance Standards SLP Single Pipe Set f 2004-05 Arctic Cat 900 Mountain Cat Carb and EFI with Transfer Outlet Tube P.N. 09-908CP/09-914CP Read instructions carefully and completely

More information

3- Remove stock silencer bracket from the bulkhead located above brake assembly (this bracket will not be used in installation).

3- Remove stock silencer bracket from the bulkhead located above brake assembly (this bracket will not be used in installation). SLP Single Pipe Set for 2004 ZR 900 P.N. 09-904CP Kit Contents: 2 1/4 Flat Washer 2 Large Head Rivets 2 1/4 Nylock Nuts 2 Rivet Washers 1 Stem Vibro Support 1 Medium Sping 1 pc 30 Reflective Heat Tape

More information

Part # SLP Single Pipe Set for G4 Ski Doo 850

Part # SLP Single Pipe Set for G4 Ski Doo 850 Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Part # 09-867 SLP Single Pipe Set for 2017-18 G4 Ski Doo 850 Parts List: 7-7 Insulated

More information

SLP PART # ATTENTION DEALER

SLP PART # ATTENTION DEALER SLP PART #09-883 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following:

More information

SLP PART # ATTENTION DEALER

SLP PART # ATTENTION DEALER SLP PART #09-872 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following:

More information

Classes INC. Northeast Snowmobile Racing INC SNOW DRAG RACING. Classes. Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open

Classes INC. Northeast Snowmobile Racing INC SNOW DRAG RACING. Classes. Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open INC Northeast Snowmobile Racing INC Classes SNOW DRAG RACING Classes Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open Improved Trail: 500, 600, 700, 800, Open Pro: ( $25 Entry

More information

SLP PART# ATTENTION DEALER

SLP PART# ATTENTION DEALER *015-09866* Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 PART# 09-866 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION

More information

Part # SLP Silencer for G4 Ski Doo 850

Part # SLP Silencer for G4 Ski Doo 850 Part # 09-867 SLP Silencer for 2017-18 G4 Ski Doo 850 Parts List: 7-7 Insulated Heat Tape (Part #090-29) 5-30 Reflective Heat Tape (Part #090-31) 1 - Inner Aluminum Heat Shield (Part #091-6057) 3-3/16

More information

Single Pipe for Ski-Doo REV H.O. (For use with ported engines only) #09-870

Single Pipe for Ski-Doo REV H.O. (For use with ported engines only) #09-870 the World s Performance Standards Single Pipe for 200-2006 Ski-Doo REV H.O. (For use with ported engines only) #09-870 Important: Read instructions carefully before installation. 1. Remove stock pipe and

More information

SLP Single Pipe Set for 2007 Arctic Cat M1000

SLP Single Pipe Set for 2007 Arctic Cat M1000 Single Pipe Set for 2007 Arctic Cat M1000 P.N. 09-876 Kit Contents: 1 - Silencer 1 - Spring Tab 1 - Large Head Rivet 1 - Short Spring 1 - Zip Tie 1-30 Reflective Heat Tape 1 - Y-Pipe 1 - Single Pipe Read

More information

2018 Junior Sprint Rules

2018 Junior Sprint Rules 2018 KidSprint Engine Rules Briggs World Formula 2018B All parts must be Briggs & Stratton factory production parts unless otherwise noted in these rules. No machining, polishing or alteration of any parts

More information

SLP Stage 2 Performance Kit for Polaris 800 Axys

SLP Stage 2 Performance Kit for Polaris 800 Axys Setting the World s Performance Standards 743 E. Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Stage 2 Performance Kit for 2015-17 Polaris 800 Axys The following tuning specification

More information

Performance Edition Kit (SLP Stage 4)

Performance Edition Kit (SLP Stage 4) Performance Edition Kit ( Stage 4) for 2011-15 Polaris 800 RMK, Pro-RMK, Switchback Assault, RMK Assault & Indy 2011-14 800 Rush & Switchback Congratulations! You have just purchased one of the best modifications

More information

Setting the World s Performance Standards

Setting the World s Performance Standards Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Lightweight Silencer for Polaris: 2016-17 800 Axys Models & 2017 600 Pro-RMK P/N 09-322

More information

Skidoo XM Etec Installation Instructions

Skidoo XM Etec Installation Instructions Thank you for purchasing your Silber Turbo kit. This product was designed to give you endless amounts of power and satisfaction. During the installation feel free to call us with any question or concerns

More information

Stock rubber isolator must remain in this location

Stock rubber isolator must remain in this location *015-09319* Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Lightweight Silencer for Polaris: 2015-18 800 Axys Models & 2016-18 600

More information

10. Oil injection pump must remain functional and in place lines may be removed and plugged. Premix gasoline may be used.

10. Oil injection pump must remain functional and in place lines may be removed and plugged. Premix gasoline may be used. STOCK SNOWMOBILE GENERAL REQUIREMENTS 1. The snowmobile must use OEM clutch, suspension, gas tank, cowl, hood and engine for the snowmobiles year and model. Factory options are not 2. Snowmobile and driver

More information

Local Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # engine will be allowed in this class.

Local Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # engine will be allowed in this class. Local Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # 124332-8201engine will be allowed in this class. o All parts will be stock unaltered Briggs & Stratton Animal

More information

INSTRUCTIONS. High Boost Upgrade Polaris PRO-RMK Polaris SKS 850 (155) 2019 Polaris ASSAULT 850. Page Number: 1 INSTRUCTIONS MODEL:

INSTRUCTIONS. High Boost Upgrade Polaris PRO-RMK Polaris SKS 850 (155) 2019 Polaris ASSAULT 850. Page Number: 1 INSTRUCTIONS MODEL: INSTRUCTIONS MODEL: FITS: High Boost Upgrade 2019 Polaris PRO-RMK 850 2019 Polaris SKS 850 (155) 2019 Polaris ASSAULT 850 Page Number: 1 INSTRUCTIONS Table of Contents Contents INSTRUCTIONS...1 Contents

More information

CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION

CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION V-Twin MFG. VT No. 32-9500 V-TECH 1 IGNITION KIT, SINGLE FIRE FITS EV SHOVEL, XL THRU 1997 VT No. 32-9503 V-TECH 1 IGNITION KIT, SINGLE FIRE FITS EV, SHOVEL, XL, WITH COIL AND WIRES This is a custom application

More information

CS340ES. Property of - Not for Resale A1

CS340ES. Property of   - Not for Resale A1 A1 CYLINDER HEAD - CYLINDER 1 8G8-11111-00-00 HEAD, CYLINDER 1......... 1 2 8G8-11121-00-00 HEAD, CYLINDER 2......... 1 3 NGK-BR9ES-00-00 PLUG, SPARK............. 2 4 8G8-11181-01-00 GASKET, CYLINDER HEAD

More information

Clutching for 2019 Polaris 850 RMK

Clutching for 2019 Polaris 850 RMK Clutching for 2019 Polaris 850 RMK Important: The following clutching information has been thoroughly tested and is highly recommended for proper performance and reliability. Primary weights, drive spring

More information

NOVICE 1, 2 & JUNIOR 1 & 2 DIVISIONS

NOVICE 1, 2 & JUNIOR 1 & 2 DIVISIONS NOVICE 1, 2 & JUNIOR 1 & 2 DIVISIONS 708 BRIGGS LOCAL OPTION 206 Briggs & Stratton (B&S) Model 124332 Type 8201 only. The intent of this class is to provide a sealed, simple-to-operate, ultra dependable

More information

World Formula TECH MANUAL

World Formula TECH MANUAL World Formula TECH MANUAL Section 1 General Rules 1. Only stock Briggs & Stratton World Formula Model # 124435-8101 will be used in this class except as provided in this Tech manual. All parts will be

More information

Setting the World s Performance Standards

Setting the World s Performance Standards Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Forced Air Hot Air Elimination Kit (Bed Fan Kit) For 800 RZR-4 P/N 67-165 Kit Contents:

More information

Revised 10/22/2014 Page 2 of?

Revised 10/22/2014 Page 2 of? 1.Remove side panels, hood, seat, fuel tank, and 2.Remove stock air box, remove fuel line muffler. Save exhaust springs and rubber muffler mounts for turbo bracket. Sand back surface flat for mounting.

More information

Kid Sprint Engine Rules Briggs World Formula

Kid Sprint Engine Rules Briggs World Formula Kid Sprint Engine Rules Briggs World Formula 2017 Jr Sprint Engine Rules Briggs World Formula effective 2/1/2017. All parts must bebriggs & Stratton factory production parts unless otherwise noted in these

More information

INSTALLATION INSTRUCTIONS for HI-1 and HI-2 MOTORCYCLE IGNITIONS. Part Numbers and INTRODUCTION COIL AND SPARK PLUG CABLE CONSIDERATIONS

INSTALLATION INSTRUCTIONS for HI-1 and HI-2 MOTORCYCLE IGNITIONS. Part Numbers and INTRODUCTION COIL AND SPARK PLUG CABLE CONSIDERATIONS INSTALLATION INSTRUCTIONS for HI- and HI- MOTORCYCLE S Part Numbers 8-000 and 8-000 CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION INTRODUCTION Crane HI- and HI- ignition systems are

More information

BA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)

BA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit

More information

2007 HOP-UP INFORMATION. Foreword

2007 HOP-UP INFORMATION. Foreword 2007 HOP-UP INFORMTION Foreword This manual contains the hop-up information for RM series of European specification and is intended to allow the standard model to achieve its maximum performance potential.

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: C

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: C Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-721C 2011-2013 MINI Cooper S L4-1.6L SEE NOTE* 2011-2013 MINI Clubman S L4-1.6L SEE NOTE* 2011-2013 MINI Cooper

More information

TURBO KIT INSTRUCTIONS

TURBO KIT INSTRUCTIONS Revision 12/20/10 TURBO KIT INSTRUCTIONS This turbo kit consists of the necessary parts to upgrade or add a turbo to your 22R/RE/RET. This kit may require some fabrication to address your particular application

More information

... TX-L MODEL NUMBER CONTENTS 2-3 BODY. 4-6 HOOD ASSEMBLY IGNITION ASSEMBLY. 8-9 SEAT ASSEMBLY STEERING ASSEMBLY.

... TX-L MODEL NUMBER CONTENTS 2-3 BODY. 4-6 HOOD ASSEMBLY IGNITION ASSEMBLY. 8-9 SEAT ASSEMBLY STEERING ASSEMBLY. .. ~ : l~ :;~, ~ 0 J-I-'olaris I I '. ... TX-L MODEL NUMBER 080639 CONTENTS BODY. HOOD ASSEMBLY IGNITION ASSEMBLY. SEAT ASSEMBLY... STEERING ASSEMBLY. CHAINCASE ASSEMBLY. DRIVE CLUTCH. DRIVEN CLUTCH. DRIVE

More information

2008 Arctic Cat 600 Sno Pro. Race School November 8, 2007 General Chassis Information Presented by Brian Dick

2008 Arctic Cat 600 Sno Pro. Race School November 8, 2007 General Chassis Information Presented by Brian Dick 2008 Arctic Cat 600 Sno Pro Race School November 8, 2007 General Chassis Information Presented by Brian Dick Chassis Self Pierce Riveted (SPR) tunnel assembly Engine/Lower Arm Frame assembly Upper Spar

More information

AMMC JUNIOR CLASS RULES

AMMC JUNIOR CLASS RULES AMMC JUNIOR CLASS RULES Classes Semi Pro: Pro: Ages 9-13, Machine: 0-550cc Fan Cooled Ages 13-17, Machine: 0-600cc Fan Cooled/Liquid Cooled GENERAL Snowmobile must have OEM engine, hood, intake, exhaust,

More information

General Rules for ALL classes: (Please read these rules and understand them before you sign up.)

General Rules for ALL classes: (Please read these rules and understand them before you sign up.) 2019 Long Lake Vintage Snowmobile Racing Association General Rules for ALL classes: (Please read these rules and understand them before you sign up.) NO CHANGES, Modification allowed UNLESS specified in

More information

#100 TO #199 SPORTSMAN 1600 LIGHT BUGGY TECHNICAL SPECIFICATIONS

#100 TO #199 SPORTSMAN 1600 LIGHT BUGGY TECHNICAL SPECIFICATIONS #100 TO #199 SPORTSMAN 1600 LIGHT BUGGY TECHNICAL SPECIFICATIONS DEFINITION 1600 Light Buggy is a one-person, limited 4-wheel car using Volkswagen type 1 stock components with a 1585 cc engine. All parts

More information

Big Block Installation

Big Block Installation Factory Five Racing, Inc. Big Block Installation 427 Shown here with fuel injection. 1 These instructions are designed to supplement the assembly manual where the assembly process is different from the

More information

DDR SERIES SYSTEM INSTALLATION INSTRUCTIONS

DDR SERIES SYSTEM INSTALLATION INSTRUCTIONS DDR SERIES SYSTEM INSTALLATION INSTRUCTIONS Read all Instructions before beginning!!!! Caution EXTREME DANGER Caution Do not use or mix any other manufacturer s products with any Nitrous Express products.

More information

SSK.1.3 Sound level shall not exceed 86 db(a) at 22.86m (75 ft.). See Section 19.5 (pg. 78).

SSK.1.3 Sound level shall not exceed 86 db(a) at 22.86m (75 ft.). See Section 19.5 (pg. 78). SKI Division SSK.1 SKI STOCK CLASS COMPETITION Intended to promote interest in Ski type personal watercraft competition, at a baseline level, and to enable individuals to become active competitors with

More information

Sno Pro 120. Model Number S2012ACAAAUSG SHARE OUR PASSION.

Sno Pro 120. Model Number S2012ACAAAUSG SHARE OUR PASSION. 2012Snowmobile Illustrated Parts Manual Sno Pro 120 Model Number S2012ACAAAUSG TM SHARE OUR PASSION. TABLE OF CONTENTS 2012 Sno Pro 120 (Model No. S2012ACAAAUSG) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY...

More information

AC 120 MODEL NUMBER S2008ACAAAUSG MODEL NUMBER S2008ACAAAUSP

AC 120 MODEL NUMBER S2008ACAAAUSG MODEL NUMBER S2008ACAAAUSP 2008 AC 120 Illustrated Parts Manual MODEL NUMBER S2008ACAAAUSG MODEL NUMBER S2008ACAAAUSP TABLE OF CONTENTS (Model No. S2008ACAAAUSG) (Model No. S2008ACAAAUSP) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY...

More information

Polaris Axys Sidekick Installation Instructions

Polaris Axys Sidekick Installation Instructions 2016-2017 Polaris Axys Sidekick Installation Instructions 1. Remove hood and side panels. 2. Remove fasteners and slide console back. 3. Remove belt and driven clutch. 4. Remove clutch cover/ oil-tank

More information

Typical Install Instructions

Typical Install Instructions Typical Install Instructions Read & understand all steps of these instructions before beginning this installation. WEBER Conversion Kit, VW T-1/2, up to 1835cc 32 / 36 DFEV Weber Carburetor These instructions

More information

Racing Performance Catalog & Reference Guide Model/Type:

Racing Performance Catalog & Reference Guide Model/Type: Version 4/08 Racing Performance Catalog & Reference Guide Model/Type: 124435 8105-01 Table of Contents SAFETY... 1 WORLD FORMULA General Specs...3 Special Tools...3 Torque Specs...3 Racing Specifics...3

More information

FUEL SYSTEM. Table of Contents. Specifications. Section 3A Fuel Delivery System. Models 6/8/9.9/10/15 CARBURETOR SPECIFICATIONS

FUEL SYSTEM. Table of Contents. Specifications. Section 3A Fuel Delivery System. Models 6/8/9.9/10/15 CARBURETOR SPECIFICATIONS FUEL SYSTEM Section 3A Fuel Delivery System Table of Contents Specifications............................. 3A-1 WMC Carburetor Specifications............. 3A-2 WMC Carburetor Specifications.............

More information

X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY

X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 2 of 80 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3570-001 1 /P Intake,

More information

CYLINDER HEAD - CYLINDER

CYLINDER HEAD - CYLINDER A1 CYLINDER HEAD - CYLINDER 1 8AY-11111-00-00 HEAD, CYLINDER 1......... 1 2 8A7-12499-00-00 JOINT................... 1 3 NGK-BR9ES-00-00 PLUG, SPARK............. 2 4 8AY-11181-00-00 GASKET, CYLINDER HEAD

More information

Illustrated Parts Manual

Illustrated Parts Manual ARCTIC CAT SHARE OUR PASSION. TM Illustrated Parts Manual AC 120 Model Number S2007ACAAAUSG Model Number S2007ACAAAUSO 2007 TABLE OF CONTENTS 2007 AC 120 (Model No. S2007ACAAAUSG) (Model No. S2007ACAAAUSO)

More information

ATV I l. l u. r a. Parts Manual ARCTIC CAT. 250 cc/300 cc

ATV I l. l u. r a. Parts Manual ARCTIC CAT. 250 cc/300 cc 2000 I l l u st ATV 250 cc/300 cc Model No. A2000ATE2AUSG (250 - Green) Model No. A2000ATE2AUSR (250 - Red) Model No. A2000ATF2AUSG (300 2x4 - Green) Model No. A2000ATF2AUSR (300 2x4 - Red) Model No. A2000ATF4AUSG

More information

TRAIL RMK 136 Model #S02SR5BS. E 2001 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /01

TRAIL RMK 136 Model #S02SR5BS. E 2001 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /01 TRAIL RMK Model #S0SRBS E 00 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /0 This page left blank intentionally. ACCS... AIR BOX... BLOWER HOUSING... BRAKE... CARBURETOR... CHAINCASE... CONSOLE...

More information

DFAC 72 or DFAC 95. U.S. Patent # 6,346,056

DFAC 72 or DFAC 95. U.S. Patent # 6,346,056 Congratulations! You have purchased the finest clutch kit available. This patented "dual quadrant" technology is revolutionary to the industry! This technology is ONLY AVAILABLE from Super Torquer Systems,

More information

Motorcycle Carburetor Theory 101

Motorcycle Carburetor Theory 101 Motorcycle Carburetor Theory 101 Motorcycle carburetors look very complex, but with a little theory, you can tune your bike for maximum performance. All carburetors work under the basic principle of atmospheric

More information

IAG Street Series Air / Oil Separator (AOS) For WRX

IAG Street Series Air / Oil Separator (AOS) For WRX P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

TORC SERIES COMPETITION RULES FOR SPORTSMAN 1600 BUGGY

TORC SERIES COMPETITION RULES FOR SPORTSMAN 1600 BUGGY TORC SERIES COMPETITION RULES FOR SPORTSMAN 1600 BUGGY DEFINED AS- A limited 4-wheel vehicle utilizing a type-1, 1600 c.c. Volkswagen air-cooled engine with one person in the vehicle. Division rules supersede

More information

Illustrated Parts Manual. ZR 120 Model Number S2005ZRAAAUSG Model Number S2005ZRAAAUSR

Illustrated Parts Manual. ZR 120 Model Number S2005ZRAAAUSG Model Number S2005ZRAAAUSR Illustrated Parts Manual ZR 120 Model Number S2005ZRAAAUSG Model Number S2005ZRAAAUSR 2 00 5 TABLE OF CONTENTS 2005 ZR 120 (Model No. S2005ZRAAAUSG) (Model No. S2005ZRAAAUSR) SKI AND SPINDLE ASSEMBLY.................................................

More information

Revised 10/23/2015 Page 2 of 10

Revised 10/23/2015 Page 2 of 10 1.Remove the gauge, side panels, hood and headlight. Remove the air box from the throttle bodies then remove the seat and gas tank. 2.Carefully remove temp sensor from air box using a small pick or screw

More information

Pump Gas Instructions for Polaris And 800 Models. Important Information before Installing This System:

Pump Gas Instructions for Polaris And 800 Models. Important Information before Installing This System: Pump Gas Instructions for Polaris 600 700 And 800 Models Important Information before Installing This System: Before you begin your turbo install, read through these instructions to determine if you are

More information

Briggs & Stratton. World Formula & Modified World Formula. Tech Manual

Briggs & Stratton. World Formula & Modified World Formula. Tech Manual Briggs & Stratton World Formula & Modified World Formula Tech Manual First Issued: May 22, 2007 Updated: January 2017 Jerry Mostek QMA Tech 2012 Quarter Midgets of America, Inc. WORLD FORMULA CLAIM RULE

More information

Illustrated Parts Manual

Illustrated Parts Manual 2010 Illustrated Parts Manual 120 Sno Pro Model Number S2010ACAAAUSG SHARE OUR PASSION ṬM TABLE OF CONTENTS 2010 120 Sno Pro (Model No. S2010ACAAAUSG) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY... 2

More information

Owner smanual. Banks Techni-Cooler System Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987

Owner smanual. Banks Techni-Cooler System Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987 Owner smanual with Installation Instructions Banks Techni-Cooler System 2013-16 Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987 Gale Banks Engineering 546 Duggan Avenue

More information

ELECTRIC START KIT KIT P/N

ELECTRIC START KIT KIT P/N ELECTRIC START KIT KIT P/N 2873876 Application 2002 Polaris EDGE Models with 500-600 Domestic Engines Before you begin, read these instructions and check to be sure all parts and tools are accounted for.

More information

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

Garden Tractor Rules Tuesday, July 23, :00pm

Garden Tractor Rules Tuesday, July 23, :00pm Garden Tractor Rules Tuesday, July 23, 2019 7:00pm Classes: Premiums: 1. Youth 900 lb. 12 HP and under 1 st - $25; 2 nd - $15; 3 rd - $10 2. Youth 900 lb. 16 HP and under 1 st - $25; 2 nd - $15; 3 rd -

More information

Arctic Cat ProClimb Sidekick Installation Instructions

Arctic Cat ProClimb Sidekick Installation Instructions 2013-2017 Arctic Cat ProClimb Sidekick Installation Instructions 1.Remove side panels, front bumper, and hood 2. Remove pipe, muffler, heat shield and ECU 3. Remove cross brace. Unplug the servo motor

More information

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles) P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

INSTALLATION INSTRUCTIONS for HI-4 DUAL FIRE MOTORCYCLE IGNITION. Part Number INTRODUCTION REMOVAL OF POINTS IGNITION TO 1977 MODELS

INSTALLATION INSTRUCTIONS for HI-4 DUAL FIRE MOTORCYCLE IGNITION. Part Number INTRODUCTION REMOVAL OF POINTS IGNITION TO 1977 MODELS INSTALLATION INSTRUCTIONS for HI- DUAL FIRE MOTORCYCLE IGNITION Part Number -00 CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION INTRODUCTION The HI- ignition system is intended for use

More information

PART NUMBER: MINI Cooper S L4-1.6L SEE * NOTE

PART NUMBER: MINI Cooper S L4-1.6L SEE * NOTE Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-699 2007-2010 MINI Cooper S L4-1.6L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may

More information

400 2x4/4x4 EFT SHARE OUR PASSION ṬM

400 2x4/4x4 EFT SHARE OUR PASSION ṬM SHARE OUR PASSION ṬM 400 2x4/4x4 EFT Model Number A2009IDG2BETR (Red - 2x4) Model Number A2009IDG2BETZ (Cat Green - 2x4) Model Number A2009IDG4BETR (Red - 4x4) Model Number A2009IDG4BETG (Green - 4x4)

More information

Reproduction. Not for. Briggsracing.com. CORPORATION Briggs & Stratton Corporation MS /08

Reproduction. Not for. Briggsracing.com. CORPORATION Briggs & Stratton Corporation MS /08 Briggsracing.com MS-5702-4/08 BRIGGS&STRATTON CORPORATION Post office box 702 Milwaukee, WI 53201 USA 414 259 5333 2008 Briggs & Stratton Corporation Version 4/08 Racing Performance Catalog & Reference

More information

TSS Fit Kit Installation Instructions Timbersled Snow Bike System

TSS Fit Kit Installation Instructions Timbersled Snow Bike System TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for

More information

TOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation

TOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear

More information

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation

More information

DISPLACEMENT: The maximum displacement that may be achieved in the Ski Superstock Class is 1500 cc.

DISPLACEMENT: The maximum displacement that may be achieved in the Ski Superstock Class is 1500 cc. SKSS.1 SUPERSTOCK CLASS COMPETITION Competitors in this class are allowed modifications to gain maximum machine and engine performance while restricting the build costs by prohibiting aftermarket hulls

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL F-SERIES DUAL ALTERNATOR VERSION 10/07 Blackbird Installation Supplement for Ford 6.0. Liter Dual Alternator Parts included in the 6.0

More information

Factory Pipe Bill of Materials 650 Super Jet

Factory Pipe Bill of Materials 650 Super Jet Factory Pipe Bill of Materials 650 Super Jet Item# Qty. Part Description 1 1 Factory Pipe tunable cast aluminum headpipe 2 1 Factory Pipe aluminum chamber 3 1 Factory Pipe tuned exhaust manifold 4 2 100-120mm

More information

PARTS MANUAL PN and MICROFICHE PN /03. OCTANE Model #W045402DA. E 2003 Polaris Sales Inc.

PARTS MANUAL PN and MICROFICHE PN /03. OCTANE Model #W045402DA. E 2003 Polaris Sales Inc. PARTS MANUAL PN 0 and MICROFICHE PN 00 /0 OCTANE Model #W00DA E 00 Polaris Sales Inc. This page left blank intentionally. TABLE OF CONTENTS OCTANE W00DA Parts Manual BATTERY BOX... BILGE PUMP... CARBURETOR...

More information

THANK YOU FOR CHOOSING KÜRYAKYN! -cont.-

THANK YOU FOR CHOOSING KÜRYAKYN! -cont.- I N S TA L L AT I O N H Y P E R C H A R G E R A I R C L E A N E R 9 4 1 0 FITS: KAWASAKI 95-UP VN800 VULCAN PART # INCLUDED 600163 1 Hypercharger Chrome with drilled back 8513 1 K&N Filter Element 8593

More information

Counter-clockwise, view to output shaft Mixture 1:50, 2-stroke-oil, fuel min. 95 octane (RON)

Counter-clockwise, view to output shaft Mixture 1:50, 2-stroke-oil, fuel min. 95 octane (RON) HIRTH 2703 Carburated - 55 hp The 2703 V is an air cooled, piston controlled 2-cylinder-inline-2-stroke engine with one or two carburetors and Nikasil coated cylinders. It has one of the highest power

More information

2019 Street Stock Rules

2019 Street Stock Rules Presented By 2019 Street Stock Rules 1) Car Body and Frame Any stock, production American-made vehicle including Camaro, Firebird and Mustang. Pickups will be allowed 1. Trunk pan may be removed for fuel

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 31129 REARVIEW CAMERA 2006 RL Issue Date OCT 2005 PARTS LIST Attachment Kit P/N: 08B21-SJA-B00 Template Rear camera trim 6-Pin connector

More information

2015 SLED PULL Rules and Regulations

2015 SLED PULL Rules and Regulations Super Stock Diesel Trucks Maximum weight of 7500lbs with driver. All drivers must have a valid state driver s license OEM or equivalent SFI restraint system is mandatory and must be worn. 2015 SLED PULL

More information

HSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam

HSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam HSR Carburetor Total Kits Installation Instructions HSR42 Kits: HSR45 Kits: #42-8 84-99 Evo Big Twin #42-19 99 - present Twin Cam #45-2 84-99 Evo Big Twin #45-3 84-99 Evo Big Twin #45-4 99 - present Twin

More information