1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission
|
|
- Margery Booth
- 6 years ago
- Views:
Transcription
1 1998 Ford EXPEDITION Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS SECTION C: Automatic Transmission 4R Expedition/Navigator Workshop Manual REMOVAL Procedure revision date: 02/11/2000 Transmission Special Tool(s) Transmission Jack Adapter or equivalent 307-F008 ( ) Torque Converter Holding Tool (T97T-7902-A) Torque Converter Holding Tools (T81P-7902-C) Removal 1. Place the transmission range selector lever in the NEUTRAL position. 2. Disconnect the battery ground cable (14301). 3. Raise the vehicle on a hoist; refer to Section If transmission disassembly is required, drain the transmission fluid; refer to Transmission Fluid Drain and Refill in this section. 5. Remove the transmission oil filler tube nut. 6. Remove the oil filler tube. 7. Position a suitable drain pan and disconnect the transmission fluid cooler tubes (7C140) at the cooler bypass valve.
2 8. Remove the driveshaft; refer to Section On 4x4 equipped vehicles; remove the transfer case assembly. Refer to Section B. 10. On super duty/motorhome applications, the transmission mounted parking brake assembly must be removed. Refer to Section NOTE: If the vehicle is equipped with a power take-off unit all or part of the PTO unit will need to be removed. Disconnect the shift cable from the transmission. 1. Disconnect the shift cable from the manual lever. 2. Disconnect the cable housing from the bracket and position aside. 12. Disconnect the digital transmission ranger (TR) sensor connector. 13. Disconnect the solenoid body connector. 14. If equipped, disconnect the turbine shaft speed (TSS) sensor and the output shaft speed (OSS) sensor. 15. Remove the starter motor (11001). Refer to Section On gasoline engines, remove the cylinder block opening cover.
3 17. On gasoline engines, disconnect the torque converter (7902). Rotate the crankshaft to position the torque converter-to-flexplate nut in the center of the cylinder block opening. Remove and discard the torque converter-to-flexplate nuts. 18. On gasoline engines, remove the flexplate inspection cover. 1. Remove the bolts. 2. Remove the inspection plate. 19. On diesel engines, remove the inspection cover. 1. Remove the bolts. 2. Remove the cover. 20. On diesel engines, remove and discard the torque converter-to-flexplate nuts. 21. CAUTION: Make sure any securing straps or the transmission jack adapter do not touch the cooler bypass valve (CBV). Do not use the CBV as a handle. Damage to the CBV may cause a leak and/or failure to the transmission assembly. Install the High Lift Transmission Jack with the Transmission Jack Adapter to the transmission.
4 22. Remove the exhaust and crossmember; refer to Section Remove the transmission. 1. Remove the six transmission-to-engine (diesel) mounting bolts or seven transmission-to-engine (gasoline) mounting bolts. 2. Gently rock the transmission side-to-side to disengage it from the locator dowels. 3. Move the transmission and the transmission jack rearward to clear the engine flexplate. 24. Install Torque Converter Holding Tool. 25. CAUTION: Use care while removing the transmission to avoid obstructions. CAUTION: Do not use the cooler bypass valve as a handle. Damage to the cooler bypass valve assembly may occur or damage to the case may result. CAUTION: If a safety strap is being used to hold the transmission to the High-Lift Transmission Jack, place the strap behind the cooler by-pass valve (CBV) to prevent damage to the cooler by-pass valve. Wiggle the transmission back and forth and lower the transmission out of the vehicle. 26. Remove the Torque Converter Holding Tool. 27. WARNING: The torque converter is very heavy. NOTE: Fluid loss will occur when the torque converter is removed. If required. remove the torque converter from the transmission (7003). 1. Install the Torque Converter Handles and position them at 6 o'clock and 12 o'clock. 2. Carefully remove the (A) torque converter from the (B) transmission by pulling evenly on the handles.
5
2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
More informationSECTION Automatic Transaxle/Transmission 4R70E/4R75E
307-01-i Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)... 307-01-2 307-01-2 Automatic
More informationTransmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
More information1999 Explorer/Mountaineer Workshop Manual
Page 1 of 5 SECTION 307-01B: Automatic Transmission 5R55E 1999 Explorer/Mountaineer Workshop Manual REMOVAL Procedure revision date: 07/27/1998 Transmission Special Tool(s) Torque Converter Holding Tool
More informationTransmission. Special Tool(s) Installation. All vehicles
Transmission Special Tool(s) Installation All vehicles 1. CAUTION: Prior to the installation of the transmission, the fluid, cooler lines and the cooler bypass valve must be cleaned. Transmission failure
More informationTransmission. All vehicles
INSTALLATION: TRANSMISSION (A... INSTALLATION: TRANSMISSION (AUTOMATIC TRANSAXLE/TRANSMISSION) 307 01 Automatic Transaxle/Transmission 2006 Mustang INSTALLATION Procedure revision date: 07/11/2008 All
More informationF o r d I n s t a l l a t i o n I n s t r u c t i o n s
1 DO NOT USE WATER-BASED TRANSMISSION FLUSHING FLUID THE LINING IN THE CONVERTOR CLUTCHES WILL DISINTIGRATE, RENDERING THE CONVERTOR USELESS AND WARRANTY WILL BE VOIDED. BD PERFORMANCE TRANSMISSION F o
More informationIN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
More informationPage 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
More informationBD PERFORMANCE TRANSMISSION
1 BD PERFORMANCE TRANSMISSION 2008-10 F o r d 6. 4 L ( 5 R 1 1 0 ) I n s t a l l a t i o n I n s t r u c t i o n s 4WD Part # 1064494 2WD Part # 1064492 Please read the instructions and warranty disclaimer
More informationBD PERFORMANCE TRANSMISSION
1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD PERFORMANCE TRANSMISSION 2008-10 F o r d 6. 4 L ( 5 R 1 1 0 ) I n s t a l l a t i o n I n s t r u c t i o n s 4WD Part # 1064494 2WD Part
More information2002 F-Super Duty /Excursion Workshop Manual
Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring
More information1998 Contour/Mystique Workshop Manual
SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290
More information2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
More information1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
More informationIN-VEHICLE REPAIR. Main Control Valve Body. Removal. 6. Disconnect the transaxle wiring harness electrical connector and TR sensor connector.
307-01-1 Automatic Transaxle/Transmission 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Material Item Thread Sealant with PTFE TA-24 Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid XT-2-QDX
More informationSTEPS Install the (A) input shaft with long spliced end first. Install the (B) aligning pin.
1999 Ford Truck Econoline E450 Super Duty V10-6.8L VIN S Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > 4R100 > Assembly STEPS 51-94 51. Install
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More informationChevrolet Ford Dodge LCT1000--LCT RH / 47RE / 48RE E4OD / 4R100. Transmission removal, Installation And testing
ATS Transmission Procedures Chevrolet Ford Dodge LCT1000--LCT2500 47RH / 47RE / 48RE E4OD / 4R100 Transmission removal, Installation And testing Please read before any work is done Removal NOTE: NOTE:
More information1996 Aerostar/Ranger/Explorer
Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch
More informationIN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
More information1999 Ford EXPLORER. Submodel: Engine Type: V8 Liters: 5.0 Fuel Delivery: FI Fuel: GAS. Main Control Valve Body
1999 Ford EXPLORER Submodel: Engine Type: V8 Liters: 5.0 Fuel Delivery: FI Fuel: GAS SECTION 307-01A: Automatic Transmission 4R70W 1999 Explorer/Mountaineer Workshop Manual DISASSEMBLY AND ASSEMBLY OF
More informationPage 1 of 8 2012 Ford F450 Super Duty 6.7L Eng Service Manual: ENGINE MECHANICAL - 6.7L DIESEL -- F250-F550 SUPER DUTY IN-VEHICLE REPAIR > OIL PAN - LOWER MATERIAL SPECIFICATIONS Item Motorcraft SAE 0W-30
More informationDISASSEMBLY. Transmission. All vehicles
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 DISASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Remover, Servo 307-347 (T97T-7D021-A)
More informationIN-VEHICLE REPAIR. Oil Pan Lower. Removal. 2. Disconnect the LH and RH battery ground cables. For additional information, refer to Section
303-01C-1 IN-VEHICLE REPAIR Oil Pan Lower Special Tool(s) 3-Bar Engine Support 303-F070 Lifting Eyes 303-D030 303-01C-1 2. Disconnect the LH and RH battery ground cables. For additional information, refer
More information1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More informationDISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More informationOwner smanual. Banks Billet Torque Converter
Owner smanual with Installation Instructions Banks Billet Torque Converter 2003-2007 Ford Power Stroke 6.0L Turbo-Diesel Pickups Equipped with TorqShift Transmissions 2005-2009 Ford 6.8L V10 Gas Pickup,
More informationDIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control module (PCM) 1 Pressure control solenoid
More informationREMOVAL AND INSTALLATION
310-00-1 Fuel System 310-00-1 REMOVAL AND INSTALLATION Fuel Tank and Filler Pipe Special Tool(s) Fuel Tank Drain Hose 310-F013 2. NOTE: Steps 2 through 5 are only necessary if servicing the fuel tank or
More information2004 Lincoln LS Workshop Manual
SECTION 310-00: Fuel System 2004 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/23/2004 Fuel Tank and Filler Pipe Printable View (541 KB) Special Tool(s) Fuel Drain Hose
More informationAutomatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
More informationDIAGNOSIS AND TESTING
307-01-1 Automatic Transmission 5R55S 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control Module (PCM) C175b 1 Shift Solenoid A (SSA)
More informationEngine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
More informationfile://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...
Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight
More information1999 F-Super Duty Workshop Manual
SECTION 308-02: Clutch Controls 1999 F-Super Duty 250-550 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/2/2000 Clutch Master Cylinder and Reservoir Removal CAUTION: Remove the entire
More informationSECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE IN-VEHICLE REPAIR Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission
More informationDISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.
308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More informationDESCRIPTION AND OPERATION. Description
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk73001.htm~gen~ref.htm Page 1 of 1 Section 07-03: Transmission, Manual, M5OD DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Description The M5OD
More information2006 Freestar/Monterey Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 12/01/2005
SECTION 303-01: Engine 3.9L and 4.2L IN-VEHICLE REPAIR Procedure revision date: 12/01/2005 Valve Cover LH Item Part Number Description 1 W708650 Oil level indicator tube bolt 2 6754 Oil level indicator
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
More information2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More information2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More information2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
More information1998 Escort/Tracer Workshop Manual
Page 1 of 11 SECTION 307-01: Automatic Transaxle/Transmission 1998 Escort/Tracer Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 03/05/1998 Main Control Valve Body Assembly
More informationWorkshop Manual. F-Super Duty : Powertrain. 03: Engine
Workshop Manual 1999 F-Super Duty 250-550 3: Powertrain 03: Engine 1999 F-Super Duty 250-550 Contents/Index GROUP 03: Engine SECTION 303-00: Engine System General Information SECTION 303-01A: Engine 5.4L
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More informationPage 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
More information1994 Bronco/Econoline/F-Series
Page 1 of 8 Section 10-01A: Fuel Tank, Filters, Lines and Electric Fuel Pump, Gasoline Engines REMOVAL AND INSTALLATION 1994 Bronco/Econoline/F-Series Workshop Manual Fuel Tank Steel Midship Fuel Tank,
More informationFUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".
More information2003 Escape Workshop Manual
Page 1 of 6 SECTION 211-02: Power Steering 2003 Escape Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/06/2005 Steering Gear Printable View (633 KB) Special Tool(s) Tie-Rod End Remover
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More information2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 16 SECTION 303-01C: Engine 7.3L Diesel DISASSEMBLY Procedure revision date: 05/21/2002 Engine Printable View (1761 KB) Special Tool(s) Cylinder Head Lifting Tool (D94T-6000-B) 303-D098 Damper
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More information2000 Ranger Workshop Manual
SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)
More informationFUEL PUMP CAMSHAFT TIMING CHECK
PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,
More information1994 Ford Mustang - Engine Mechanical > Engine Mechanical Components > Timing Chain Cove...
Page 1 of 6 1994 Ford Mustang : Engine Mechanical > Engine Mechanical Components > Timing Chain Cover & Seal > Removal & Installation > 5.0L Engine 5.0L Engine 1. Disconnect the negative battery cable
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationCrankshaft Rear Seal with Retainer Plate
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Crankshaft Rear Seal with Retainer Plate Special Tool(s) Installer, Crankshaft Rear
More informationATTENTION ADVANCE SERVICE BULLETIN INFORMATION
SUBJECT: NO: 21-10-98 Loss Of Fifth Gear GROUP: Transmission EFFECTIVE DATE: Sep. 11, 1998 CHRYSLER MAIL MANAGEMENT SYSTEM DATE: AUG. 28, 1998 ATTENTION ADVANCE SERVICE BULLETIN INFORMATION The following
More informationfile://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
More informationItems Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 4-speed full automatic 4-speed full automatic. 2nd rd
23-2 AUTOMATIC TRANSMISSION General Information/ Service Specifications GENERAL INFORMATION 23100010141 Items Vehicles with 4G63 engine Vehicles with 4D56 engine Transmission model R4AW2-6 V4AW2-6 Type
More informationFUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )
PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND
More informationDISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
More informationDRIVE AXLES. Differentials & Axle Shafts - Corvette
DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case
More informationEngine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
More informationSERVICE MANUAL Gearbox - Allison AT545 - Gearbox Installation
Gearbox - Allison AT545 - Gearbox Installation Oil level dipstick Gearbox oil cooler Auxiliary oil filter Modulator Page 3.4 Gearbox - Allison AT545 Checking Oil Level The dipstick and filler are situated
More information1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
More informationSteering Gear Replacement
Page 1 of 7 Steering Gear Replacement Removal Procedure Notice: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column
More informationPage 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding
More informationPage 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
More informationASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More information2005 Honda ACCORD. Submodel: EX Engine Type: V6 Liters: 3.0 Fuel Delivery: FI Fuel: GAS. Automatic Transmission Installation. Special Tools Required
2005 Honda ACCORD Submodel: EX Engine Type: V6 Liters: 3.0 Fuel Delivery: FI Fuel: GAS Automatic Transmission Installation Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger
More informationOwner smanual. Banks Billet TM Torque Converter Chevy/GMC Duramax Allison Transmission. with Installation Instructions
with Installation Instructions Owner smanual Banks Billet TM Torque Converter 2001-2010 Chevy/GMC Duramax Allison Transmission THIS MANUAL IS FOR USE WITH KITS 72510 Gale Banks Engineering 546 Duggan Avenue
More informationService Manual. 1320, 1520 and 1720
Service Manual Service Manual 1320, 1520 and 1720 THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF NEW HOLLAND OR IT S SUCCESSORS. NEW HOLLAND AND IT S SUCCESSORS ARE NOT RESPONSIBLE
More information1995 Chevrolet S10 Pickup - 2WD
1995 Chevrolet S10 Pickup - 2WD Submodel: Engine Type: Liters: Fuel Delivery: Fuel: Draining Procedure Caution: Gasoline or gasoline vapors are highly flammable. A fire could occur if an ignition source
More informationREPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More information8/28/2018 Engine 6.0L Diesel - Cylinder Head RH - in Vehicle Repair 2006 Ford F-550 MotoLogic. Specification
2006 F-550 Applies to: 6.0L Diesel Report a problem with this article SECTION 303-01C: Engine 6.0L Diesel 2006 F-Super Duty 250-550 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/03/2006
More informationPage 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover
More informationPage 1 of 8 303-01A Engine 2.3L 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid IN-VEHICLE REPAIR Procedure revision date: 10/05/2008 Cylinder Head Special Tool(s) Alignment Plate, Camshaft 303-465 (T94P-6256-CH)
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
More informationPage 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled
More informationLB LB LLY LLY 1000
6 November 2006 GMC/Chevy Allison Performance Transmission 1 BD PERFORMANCE TRANSMISSION Allison Installation Instructions 2WD Transmissions 4WD Transmissions 1064702 2000-2003 LB7 1000 1064704 2000-2003
More informationB&M / INTRODUCTION
INSTALLATION INSTRUCTIONS FOR B&M AUTOMATIC TRANSMISSIONS REPLACING GM TH350, TH400, and TH700R4 / 4L60 (not including 4L60E / electronic shift models) B&M part numbers: 102002-103005 - 107101-107104 107105-107106
More informationTransmission Electronic Control System
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 05/23/2008 Transmission Electronic Control System Electronic System
More information2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual MERCON V
2007 Explorer SECTION 307-01A: Automatic Transaxle/Transmission 5R55S 2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual Report a problem with this article IN-VEHICLE REPAIR Procedure revision
More informationEXHAUST SYSTEM AND INTAKE MANIFOLD
J EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page EXHAUST SYSTEM... 1 EXHAUST SYSTEM DIAGNOSIS... 2 page SERVICE PROCEDURES... 3 TORQUE SPECIFICATIONS... 10 EXHAUST
More information2010 Explorer, Mountaineer, Explorer Sport Trac Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 06/11/2009
SECTION 303-01B: Engine - 4.6L 2010 Explorer, Mountaineer, Explorer Sport Trac Workshop (3V) Manual IN-VEHICLE REPAIR Procedure revision date: 06/11/2009 Engine Lubrication Components - Exploded View Brackets,
More information2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt
2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More information2001 Chevrolet Corvette V8-5.7L VIN G
1 of 14 2/21/2013 10:34 AM 2001 Chevrolet Corvette V8-5.7L VIN G Vehicle» Engine, Cooling and Exhaust» Engine» Oil Pan» Service and Repair Oil Pan Replacement Removal Procedure 1. 2. 3. Remove the front
More informationReturn to Instruction Sheet index TCI Installation Instructions for Turbo Hydramatic 350C & 250C
Page 1 of 6 Return to Instruction Sheet index TCI 326300 Installation Instructions for Turbo Hydramatic 350C & 250C NOTE: This kit was not intended for installation in transmissions that are in poor general
More information