SP904/3/4/5/7/8/10/11/13 Integrated Wireless Side Warning System

Size: px
Start display at page:

Download "SP904/3/4/5/7/8/10/11/13 Integrated Wireless Side Warning System"

Transcription

1 Fig 1 Operation Guide & Recommended Fitting Instructions. SP904/3/4/5/7/8/10/11/13 Integrated Wireless Side Warning System The SP904 integrated is a fully flexible, easily expandable vehicle blind spot warning system with a 3 year comprehensive warranty. Allowing for sensors to be installed to the cab area, nearside, offside of the body and or rear of a vehicle for reversing purposes, providing surround warning if required. It is suitable for rigid and tractor trailer vehicles with a coded wireless signal between trailer & tractor, whilst also allowing sensors fitted to the tractor to work independently when no trailer is present. OPERATION Front & sides warning on ignition Rear warnings on selecting reverse gear SPECIFICATION System shut down linked to speed usually above 12.5mph Traffic light visual warning from 1.5m for front/ side warnings (GREEN 1.5m, AMBER 1.0m, RED 0.6m) with AMBER directional LED which also flashes when obstruction within 0.6m via in cab display (CDU) Audible warning (3 loud Bleeps 0.6m) when obstruction in close proximity (side warning) Traffic light visual warning from 2.6m for rear with progressive audible bleeping (reverse gear only) Self test, self diagnosis function (see later) to ensure safe operation Fig 2 Rated Voltage 12 24v DC Operating Voltage 10v 32v Operating Temperature -20 C to 70 C Current Consumption Max 0.5A Communication Freq MHz Ultra Sonic Freq 40KHz Sensing angle 90 Speaker decibel 70dB

2 INSTALLATION Selecting the sensor hole positions is vital. Before commencing installation it is important to manually position the sensors on the vehicle to ensure correct sensing area. IF IN DOUBT TEL FOR TECHNICAL ASSISTANCE Fig3 Fig 4 A. The positional of the sensors above the road surface is vital. The optimum height is 70cm 10, always be aware before commencing installation the operating parameters of your vehicle and what you are looking to detect with the sonar system. B. The sensors should be located no further than 1 meter each apart C. See Fig 1 for suggested location of sensors(different vehicles may require a different location). Please note Cross rail and TFL require sensors around front nearside area D. Any continuous overhang can cause sonar echoes, which may confuse the processor. Again manually check position before installation commences E. It is essential that the sensors are fitted on a vertical surface so they project the ultrasonic beam parallel to the road F. Use the masking tape to accurately position the holes prior to drilling G. Drill holes diameter 26 mm (you may need to file out slightly) or attach brackets (available in standard or heavier duty) H. Insert Sensor Cables I. Ensure Arrow marked on the outer flange of the Sensor is pointing upwards in the 12 o clock position, (fig 4) J. Press the sensor home into the hole or tubular bracket, it is important that the sensors fit smoothly into the hole, excessive force may cause damage to the sensor therefore affecting the function of the system. ENSURE HOLE IS NOT TOO TIGHT as this can affect function K. It is possible you may require the sensor extension cable depending on location of sensors to be able to connect to ECU wire loom

3 Recommended Fitting Procedure ECU Attach ECU wire loom here firmly for rear sensors Attach ECU wire loom here firmly for right hand side Fig 5 Fig 6 Attach ECU wire loom here firmly for left hand side Fig 7 A. The ECU(fig 5)case is completely water proof and dirt proof B. The ECU wire loom (fig 7) for left or right side - Red power line should be connected to ignition. Black to negative C. The ECU wire loom (fig 7) for rear Red should be connect to reverse light feed, Black to negative D. NOTE ECU LOOM HAS CONNECTIONS FOR 3 SENSORS DO NOT PLUG THIS LOOM INTO CDU UNIT OR DAMAGE MAY OCCUR E. Connect each sensor cable to corresponding connection on ECU wire loom F. Plug ECU wireloom into ECU firmly at point highlighted (fig 6) through aperture/s and secure cable/s with water proof gland/s provided. The Water proof gland MUST be tightened with a spanner to ensure water proof seal

4 Recommended Fitting Procedure CDU Fig 8 Fig 9 Attach CDU sensor wireloom here Attach CDU power cable here Fig 10 Fig 11 A. The power cable should be connected to the CDU as highlighted in Fig 9 and passed through the base of the CDU bracket B. Connect the other end of the power cable Fig 10 to Ignition (Red) live, (black) negative. The speed wire is analogue (white) and should be connected to a suitable speed signal dependant on vehicle (should you decide not to connect this wire, sensors will be on all the time, in which case you must connect this wire to ground or a malfunction may occur), usually but not limited to B6 or B7 (V imp) at back of tachograph or on older tachograph PIN C3. Many vehicles will have body builder plug for speed signal, but this may need to be turned on by manufacturer/dealer. The speed signal is 5v square pattern C. Connect the CDU sensor wireloom Fig 11 to CDU as highlighted in Fig 9 D. NOTE CDU WIRE LOOM (fig11 ) HAS CONNECTIONS FOR 4 SENSORS AND ONLY USED ON SP904/4/5/7/8/10/11/13 IT IS NOT USED ON SP904/3. DO NOT PLUG CDU WIRE LOOM INTO ECU UNIT E. Connect the front sensors to the corresponding connection on the CDU wireloom F. For side sensors, please ensure CDU and ECU are on the same ignition feed, not one of Aux and one main power G. Attach the CDU bracket to the desired position in the cab, by using the 22mm countersunk screws and adhesive strip provided. H. Secure the CDU to the bracket by firmly depressing the units together I. Set the speed switch cut off by driving to desired speed and press button Fig 8 (this must only be done after ID registration and waiting at least 1 minute) J. Please note that the sensors connected to the CDU will work independently to those connected ECU K. )DUccc

5 ID Registration & Speed: Each system has an individual code supplied from the ECU and the sensors connected to the ECU will only work when ID registration has been completed. This system ensures that there will be no interference from other systems which are in close proximity. The SP904 CDU should have been pre registered with the ECU supplied. In the event of non function, please press and hold the button on the front of the CDU. You MUST do this prior to turning on ignition or for rear sensors engage reverse after pressing the button on the front of the CDU Fig 8. The CDU display will start to flash RED, release button, if successful, the display will then flash GREEN. Turn off the ignition and then turn on ignition and system should function with do-so-me tone heard. For tractor / trailer units you will need to carry out this procedure every time a trailer is changed. NOTE: THE SENSORS ON THE TRACTOR UNIT WILL CONTINUE TO FUNCTION (This tone is to confirm the CDU & ECU are communicating) The speed cut out has been set at the factory (provided you have connected the white speed 12.5mph To set the cut out at a different speed, start the engine, wait for do-so-me tone, then wait 1 minute, drive vehicle to desired cut out speed and press button on front of CDU fig 8. WARNING: DO NOT SET THE SPEED CUT OUT WHEN STATIONARY AS THIS MAY CAUSE THE SENSOR SYSTEM TO SHUT DOWN IMMEDIATELY ON START UP

6 FAULTS The SP904 integrated has a self test function for faulty sensors, when an amber light will be displayed in the CDU and an indication lamp to identify front, side or rear sensor fault. Faults on sensors connected to ECU will be displayed first. Example: Fault on sensor 2 connected to CDU and fault on Sensor C connected to rear ECU loom. CDU will display as fig 15 bleep 3 times, it will then display as fig 12 and bleep 2 times. It will follow this procedure a total of 3 times before switching off Please also see the table below Fig 12 Fig 13 fig 14 fig 15 FAULT DIAGNOSIS TABLE Fault Possible Cause Solution On start-up CDU displays as Fig 12. Single bleep every 3 seconds, 3 times On start-up CDU displays as Fig bleeps every 3 seconds, 3 times On start-up CDU displays as Fig bleeps every 3 seconds, 3 times On Start-up CDU displays as Fig 12. Single bleep followed by multiple bleeps On Start up CDU displays as Fig 13,14 or 15 Single bleep every 3 seconds 3 times Sensor on CDU cable 1 is reporting a fault Ensure sensor is correctly connected to cable or replace sensor Sensor on CDU cable 2 is reporting a fault Ensure sensor is correctly connected to cable or replace sensor Sensor on CDU cable 3 is reporting a fault Ensure sensor is correctly connected or replace sensor Multiple sensor fault reported or faulty CDU or faulty CDU wireloom Single bleep cable 1 2 bleeps cable 2 3 bleeps cable 3 4 bleeps cable 4 Sensor on ECU cable Left Fig 13 Right Fig 14 Rear Fig 15 Reporting fault on cable A Replace corresponding sensor first, if this does not resolve the issue. CDU should be replaced. Finally replace CDU wireloom Ensure sensor correctly connected or replace sensor

7 On Start up CDU displays as Fig 13,14 or 15 2 bleeps every 3 seconds 3 times Sensor on ECU cable Left Fig 13 Right Fig 14 Rear Fig 15 Reporting fault on cable B Ensure sensor correctly connected or replace sensor On Start up CDU displays as Fig 13,14 or 15 3 bleeps every 3 seconds 3 times Sensor on ECU cable Left Fig 13 Right Fig 14 Rear Fig 15 Reporting fault on cable C Ensure sensor correctly connected or replace sensor On Start up CDU displays as Fig 13, 14 or 15 alternatively with single and multiple bleeps each 3 times every 3 seconds System seems to operate very intermittently No sound or warning light from CDU Front sensors work, but side/ rear sensors do not CDU display goes red immediately when turning on ignition, bleeps 3 times and LED continues to flash CDU continues to give warning at high speed Sensor failure on more than one ECU wire loom, fault ECU or Faulty wireloom 1 bleep Sensor A 2 bleeps Sensor B 3 bleeps Sensor C Replace corresponding sensor first, if this does not resolve issue then replace ECU, finally replace Loom Sensor holes may be too tight Move sensors slightly out of their hole and check system operates. If so slightly enlarge aperture using a file and relocate sensor No obstruction detected CDU and ECU not communicating Faulty CDU Faulty ECU Speed cut out has been set to 0MPH When ECU & CDU communication do-so-me tone should be heard on start up for vehicles equipped with side sensors. The do-so-me tone will only be heard on engaging reverse on vehicles equipped with rear sensors Position vehicle within the detection parameters of the sensors Ensure both CDU wire loom and power are connected Press button on front of CDU fig 8, if this flashes red, possible failure of ECU If nothing is displayed in CDU and power connected, replace CDU Drive vehicle up to cut out speed and press CDU button No power to ECU or faulty ECU Rear sensors will only work in reverse. Sensor is detecting an obstruction Speed signal not set or speed wire not connected Turn on ignition, for side sensors and rear sensors follow ID registration procedure as outlined previously. If no do-some tone check to ensure power is being received to ECU If power received and system does not function replace ECU Ensure that there are no obstructions within the vicinity of the vehicle. There is no dead zone on the sensors therefore any overhang e.g. indicator housing will be detected or if sensors are located too close to the ground. Sensors may need to be installed in a different location Turn on engine and wait for do-so-me tone. Wait at least 1 minute. Drive to desired cut off speed e.g.10mph and press registration button fig 8 If this does not work call engineer to install signal

8 CERTIFICATIONS E Mark CE Mark

9 IP67 Sensor rating IP67 ECU rating Warning: The accurate operation of the system could be adversely affected by any of the following: Remember: Narrow radius obstacles such as wire, rope & cable. Items which absorb ultrasonic waves such as clothing, sponge & snow. Irregular reflection of ultrasonic waves on rough surfaces Strong electromagnetic waves close to the vehicle. Mud, rain & and snow covering the sensor surface. THIS DEVICE IS A DRIVING AID; THE DRIVING PROCESS IS ALWAYS THE DIRECT RESPONSIBILITY OF THE DRIVER.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Ultrasonic Rear Park Aid Kit (Kit # 9002-3000) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 4 Ultrasonic

More information

Backup Sensors Owner s Manual

Backup Sensors Owner s Manual 1ODYSSEY Backup Sensors Owner s Manual 2004 American Honda Motor Co., Inc. - All Rights Reserved. Contents Introduction... 3 Important Information... 4 How the Backup Sensors Work... 5 Limitations... 8

More information

P5000 Series Owners Manual 12/16/04 5:16 PM Page 1. Owners Manual

P5000 Series Owners Manual 12/16/04 5:16 PM Page 1. Owners Manual P5000 Series Owners Manual 12/16/04 5:16 PM Page 1 Owners Manual P5000 Series Owners Manual 12/16/04 5:16 PM Page 2 C ongratulations, You have made a wise investment and an excellent choice in selecting

More information

PARKING AID SYSTEM GENERAL 1. SPECIFICATIONS

PARKING AID SYSTEM GENERAL 1. SPECIFICATIONS 879004 123 GENERAL 1. SPECIFICATIONS 879004 The parking aid system emits the supersonic wave signals from the sensors on the rear bumper with a specific interval and detects the reflected signals from

More information

Backup Sensors User s Information CR-V

Backup Sensors User s Information CR-V Backup Sensors User s Information CR-V Contents Introduction... 3 Important Information... 4 How the Backup Sensors Work... 5 Limitations... 8 Operation... 10 Daily Inspection... 12 Caring for the Backup

More information

Backup Sensors User s Information CR-V

Backup Sensors User s Information CR-V Backup Sensors User s Information CR-V Contents Introduction... 3 Important Information... 4 How the Backup Sensors Work... 5 Limitations... 8 Operation... 10 Daily Inspection... 12 Caring for the Backup

More information

Backup Parking Sensor System

Backup Parking Sensor System User s Manual Backup Parking Sensor System 4 Rear In-Bumper Type Sensors Wireless LED Display with Built-in Audible Alert For Cars, VANs, SUVs, and Trucks MODEL 4015N FCC CE ISO9001 All Rights Reserved

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Ultrasonic Rear Park Aid Kit (Kit # 9002-3000) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 4 Ultrasonic

More information

SUBARU Rear Obstacle Detection System 2004 onward

SUBARU Rear Obstacle Detection System 2004 onward SUBARU Rear Obstacle Detection System IMPREZA 4 DOOR 2004 onward ENSURE THE SET-UP PROCEDURE IS CARRIED OUT FOLLOWING INSTALLATION (See Pg 4) IMPREZA 4 DOOR JUNE 04 MODEL ONWARDS KEY POINTS OF THE INSTALLATION

More information

REARSENTRY TM BASE KIT ROSTRA OBSTACLE SENSING SYSTEM CONTENTS

REARSENTRY TM BASE KIT ROSTRA OBSTACLE SENSING SYSTEM CONTENTS REARSENTRY TM ROSTRA OBSTACLE SENSING SYSTEM BASE KIT 250-1728 CONTENTS Parts List... 2 Parts Diagrams... 2 Before You Start... 5 Installation... 7 Troubleshooting Guide...11 Form #4713, Rev. B, 01-07-04

More information

Back-Up Sensor System

Back-Up Sensor System Back-Up Sensor System Model No.: PKC0RE Owner s Manual and Warranty Information OFF ON 0.4m/1.3ft 0.6m/2.0ft 1.0m/3.3ft 1.2m/4.0ft 1.5m/5.0ft LEFT RIGHT Read these instructions completely before using

More information

Adaptive cruise control (ACC)

Adaptive cruise control (ACC) Adaptive cruise control (ACC) PRINCIPLE OF OPERATION The Adaptive Cruise Control (ACC) system is designed to aid the driver to maintain a gap from the vehicle ahead or a set road speed if there is no slower

More information

Hyundai Accent Atlantic 2006 model on Rear Parking Aid

Hyundai Accent Atlantic 2006 model on Rear Parking Aid Hyundai Accent Atlantic 2006 model on Rear Parking Aid KEY POINTS OF INSTALLATION Ensure that the sensor is installed with the dot in the 12 o clock position and that a keyway is cut in the bumper to accommodate

More information

SUBARU Rear Obstacle Detection System 2004 onward

SUBARU Rear Obstacle Detection System 2004 onward SUBARU Rear Obstacle Detection System IMPREZA 5 DOOR 2004 onward ENSURE THE SET-UP PROCEDURE IS CARRIED OUT FOLLOWING INSTALLATION (See Pg 4) IMPREZA 5 DOOR JUNE 04 MODEL ONWARDS KEY POINTS OF THE INSTALLATION

More information

Adaptive cruise control (ACC)

Adaptive cruise control (ACC) Adaptive cruise control (ACC) PRINCIPLE OF OPERATION E94163 It is the drivers responsibility to stay alert, drive safely and be in control of the vehicle at all times. Keep the front of the vehicle free

More information

KIT Parking Sensor 814

KIT Parking Sensor 814 KIT Parking Sensor 814 INSTALLATION AND USE MANUAL UK AC 745/UK Rev. 04-01/14 1 3 x BLACK x BLUE 15 3 5 4 5 BROWN BLACK-BLUE R 13 MAIN UNIT BLACK 4 BLUE 6 6a 7 8 9 10 11 10 x 1 PRIMER 3M 498UV 13 14 15

More information

H 2 Hawkeye Reverse Assistance System Diagnostics & Frequently Asked Questions

H 2 Hawkeye Reverse Assistance System Diagnostics & Frequently Asked Questions H 2 Hawkeye Reverse Assistance System Diagnostics & Frequently Asked Questions Symptom Chart Symptom Possible Cause Repair A. No power supply to Control 1. LED Display does not prove-out when ignition

More information

Vehicle Rear Observation System With Integrated Parking Sensors

Vehicle Rear Observation System With Integrated Parking Sensors Vehicle Rear Observation System With Integrated Parking Sensors Model: CAMSBAR Installation/User Manual Features: 2.5" LCD Color Display 2 Ultra Sonic Rear Obstacle Sensors On-screen Display Function Automatically

More information

PAS(PARKING AID SYSTEM)

PAS(PARKING AID SYSTEM) (PARKING AID SYSTEM) 879003/879001/879000 (PARKING AID SYSTEM) GENERAL 1. COMPONENT SPECIFICATIONS... 3 OVERVIEW AND OPERATION PROCESS 1. SYSTEM CONFIGURATION... 2. ALARM INTERVAL AND TROUBLE SHOOTING...

More information

Rear EU Number Plate Sensor System User Manual SS-NP2

Rear EU Number Plate Sensor System User Manual SS-NP2 User Manual Introduction Congratulations on purchasing EchoMaster parking sensors. This ultrasonic detection system is designed to assist in the avoidance of obstacles while reversing. Disclaimer: EchoMaster

More information

4 Sensor Backup Obstacle Sensing System Model: ACAB104 Installation Manual

4 Sensor Backup Obstacle Sensing System Model: ACAB104 Installation Manual 4 Sensor Backup Obstacle Sensing System Model: ACAB104 Installation Manual 0 5 10 Features: Four reversing sensors detect obstacles between 1-7 feet Includes 0, 5, and 10 angle sensor sleeves to fit most

More information

Specifications. General

Specifications. General For sales & service call Transport Support Tel: +44 (0)1204 368 111 TS Rigid Inclinometer Installation and Operating Instructions ISO9001 CERTIFIED COMPANY United Registrar of Systems Cert. No.1820 Transport

More information

Backup Sensors User s Information Manual RIDGELINE

Backup Sensors User s Information Manual RIDGELINE Backup Sensors User s Information Manual RIDGELINE A Few Words About Safety Your safety, and the safety of others, is very important. Operating your vehicle s backup sensors safely is an important responsibility.

More information

Assembly instructions Original parking distance control system, Volkswagen

Assembly instructions Original parking distance control system, Volkswagen Assembly instructions Original parking distance control system, Volkswagen Set contents: 1 x controller 1 x buzzer 4 x sensor Set contents: 4 x covering rings 4 x protective rings Special tools, test and

More information

AUTOMATIC CONTROL ROLLING DOOR OPENER

AUTOMATIC CONTROL ROLLING DOOR OPENER AUTOMATIC CONTROL ROLLING DOOR OPENER INSTALLATION INSTRUCTION AUTOMATIC OBSTRUCT PHOTOELECTRIC BEAM ROLLING CODE SYSTEM AUTO CLOSE DOOR ANTI-THEFT SYSTEM INSTALLATION INSTRUCTION AND RDO OWNERS MANUAL

More information

HAWK401-A Reverse Assistance System

HAWK401-A Reverse Assistance System An ISO 9001:2008 Registered Company HAWK401-A Reverse Assistance System Introduction The HAWK401-A Reverse Assistance System is an ultrasonic distance monitoring system. When the vehicle is in reverse,

More information

Guardian System Maintenance Procedure

Guardian System Maintenance Procedure Guardian System Maintenance Procedure TITLE Guardian System Maintenance Procedure PRODUCT 1. Guardian System NUMBER MP-001 DATE 24 March 17 AUTHORISED BY Erica Collins REVISION # Original PREPARED BY Christian

More information

IMPORTANT SAFETY RECOMMENDATIONS

IMPORTANT SAFETY RECOMMENDATIONS - 1 - - 2 - IMPORTANT SAFETY RECOMMENDATIONS FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY RESULT IN SERIOUS PERSONAL INJURY, DEATH AND/OR PROPERTY DAMAGE The installation of the Automatic

More information

Hawkeye Plus Reverse Assistance System Installation Instructions

Hawkeye Plus Reverse Assistance System Installation Instructions An ISO 9001:2000 Registered Company Hawkeye Plus Reverse Assistance System Installation Instructions To aid in installation, first gain access to the connection points. Remove any interior panels covering

More information

ELECTRONIC POSITIVE AIR SHUTOFF

ELECTRONIC POSITIVE AIR SHUTOFF 12 January 2015 103675X Electronic positive air shutdown (I-00336) 1 ELECTRONIC POSITIVE AIR SHUTOFF 1036750 2007-2009 Dodge 6.7L 1036751 2010-2015 Dodge 6.7L 1036754 2008-2010 Ford 6.4L 1036755 2011-2014

More information

ADVANCED PARKING GUIDANCE SYSTEM SECTION 7 ADVANCED PARKING GUIDANCE SYSTEM. Advanced parking guidance system 192

ADVANCED PARKING GUIDANCE SYSTEM SECTION 7 ADVANCED PARKING GUIDANCE SYSTEM. Advanced parking guidance system 192 ADVANCED PARKING GUIDANCE SYSTEM SECTION 7 Advanced parking guidance system 192 191 Advanced parking guidance system The advanced parking guidance system helps back up parking by displaying a rear view

More information

WARNING WARNING WARNING. English Quick start guide CAUTION CAUTION. Installation Precautions

WARNING WARNING WARNING. English Quick start guide CAUTION CAUTION. Installation Precautions English Quick start guide Symbol Identification This manual uses symbols and icons to indicate safety precautions and concerns during the installation procedure. Be sure to carefully read and understand

More information

Bendix BlindSpotter Side Object Detection System. Installation Guide

Bendix BlindSpotter Side Object Detection System. Installation Guide Bendix BlindSpotter Side Object Detection System Installation Guide Bendix BlindSpotter Side Object Detection System BW2798 (Formerly VOIG0032) April 2013 General Table of Information Contents General

More information

CRUISE CONTROL SPEED LIMITER Rev. 4.0

CRUISE CONTROL SPEED LIMITER Rev. 4.0 INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series 231.0004530 Rev. 4.0 1 2 CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics module location... 5 4 Input

More information

Beep&Park kit fitting and operating instructions

Beep&Park kit fitting and operating instructions The kit consists of the following elements: Drill 18.5mm, 1 pc. Set of connectors, 4 pcs. Band clips, 15 pcs. Screws, 2 pcs. Control module (the type depends on the version), 1 pc. Sensors, 4 8 pcs. Single

More information

INSTALLERS PACK. Page 1

INSTALLERS PACK. Page 1 INSTALLERS PACK Page 1 Contents Installation procedure chart Installation procedure Installation Tool Requirements Installation form Tank Catalogue * Safety is paramount, use safety equipment and correct

More information

Eazidraw Cordless. Installation & Set Up Instructions. Electric Blinds & Curtains

Eazidraw Cordless. Installation & Set Up Instructions. Electric Blinds & Curtains Eazidraw Cordless Installation & Set Up Instructions Electric Blinds & Curtains Features Quiet, DC battery motor with low power consumption. Rechargeable battery with up to 500 uses between charges Fully

More information

Installation Manual for Rear Park Assist

Installation Manual for Rear Park Assist Installation help? 1. Go to www.echomaster.com 2. Click on the [Login Area] located on the side blue bar. 3. Click [Technician/Installer Training & Support Site] 4. Click [Return User/Click here to Log

More information

Transmission and Brake

Transmission and Brake TABLE OF CONTENTS Gear selector lever in automatic transmission*...-2 Driving tips for automatic transmission...-3 Gear selector lever positions...-5 Winter (W) / standard (S) mode... -11 Safety mode (automatic

More information

Bluefin Led Underwater lights.

Bluefin Led Underwater lights. Bluefin Led Underwater lights. P24 Single/Dual and Colourchange Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure

More information

CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Cruise Control Systems Celica DESCRIPTION Cruise control system consists of Cruise Control Electronic

More information

M670/M680BD MAGNALOCK SERIES Installation Instructions

M670/M680BD MAGNALOCK SERIES Installation Instructions Securitron www.securitron.com Tel 800.624.5625 techsupport@securitron.com M670/M680BD MAGNALOCK SERIES Installation Instructions Page 1 Rev. D, 12/14 Table of Contents Package Contents... 3 Mounting Hardware...

More information

Lighting GENERAL INFORMATION. Daytime running lamps. Condensation. Stop lamps. Halogen headlamps. Reversing lamps. Bi-Xenon headlamps

Lighting GENERAL INFORMATION. Daytime running lamps. Condensation. Stop lamps. Halogen headlamps. Reversing lamps. Bi-Xenon headlamps Lighting GENERAL INFORMATION There are three types of headlamp systems: Halogen high/low beam main lamp with a fill-in high beam halogen lamp alongside. Bi-xenon high/low beam main lamps with fill-in high

More information

capacity due to increased traction; particularly advantageous on road surfaces

capacity due to increased traction; particularly advantageous on road surfaces 42-800 Design and function of acceleration slip control (ASR I) A. General B. Driving with ASR I C. Overall function of ASR I D. Location of components E. Individual functions A. General The acceleration

More information

SUNROOF - SERVICE INFORMATION ADJUSTMENTS

SUNROOF - SERVICE INFORMATION ADJUSTMENTS SUNROOF - SERVICE INFORMATION DESCRIPTION OPERATION DIAGNOSIS AND TESTING POWER TOP - SUNROOF SUNROOF ASSEMBLY-MODULE REMOVAL INSTALLATION CHANNEL-DRAIN REMOVAL INSTALLATION COVER-GUIDE MECHANISM REMOVAL

More information

SPRAYSHOP ANALIZER IMPORTANT : TO BE READ BEFORE USING THE HIGH VOLTAGE FUNCTION

SPRAYSHOP ANALIZER IMPORTANT : TO BE READ BEFORE USING THE HIGH VOLTAGE FUNCTION : TO BE READ BEFORE USING THE HIGH VOLTAGE FUNCTION This equipment must not be operated by any person with a heart condition or is fitted with a pacemaker device. REMEMBER ELECTRICITY AND WATER DO NOT

More information

E61, E63, E64 BMW AG - TIS

E61, E63, E64 BMW AG - TIS VS-22 es Baugruppe/Group: 66 meeknet.co.uk/e64 Park Distance Control E60, E61, E63, E64 66 01 03 (051) weltweit Datum/Date: 06/2003 Update: 07/2004 Introduction Park Distance Control (PDC) is an item of

More information

Loose Ship Park Assist and Park View System

Loose Ship Park Assist and Park View System These features are available on all 3500 4500 and 5500 chassis/cabs. It has been developed to allow the up fitter to install back up camera (park view) and park assist (parktronics) on the up fit. Both

More information

STP116 STP188. Tyre Pressure Monitoring System. User manual

STP116 STP188. Tyre Pressure Monitoring System. User manual STP116 STP188 Tyre Pressure Monitoring System User manual What s Included Standalone display In-Vehicle Charger Wireless LCD display unit Built-in rechargeable lithium battery Auto backlight Selectable

More information

Model: PSB100. Rear Parking Sensor System. Installation Manual TABLE OF CONTENTS

Model: PSB100. Rear Parking Sensor System. Installation Manual TABLE OF CONTENTS Rear Parking Sensor System Model: PSB100 Installation Manual TABLE OF CONTENTS Warnings...2 Product Description...3 Packing List...3 Installation Instructions...4 Mounting the Sensors...4 Installing the

More information

IVTM Installation Manual

IVTM Installation Manual Integrated Vehicle Tire Pressure Monitoring IVTM Installation Manual 2nd edition Copyright WABCO 2006 Vehicle Control Systems An American Standard Company The right of amendment is reserved Version 002/06.06(us)

More information

INSTALLATION INSTRUCTIONS:

INSTALLATION INSTRUCTIONS: INSTALLATION INSTRUCTIONS: The CA-5030 is an ultrasonic parking assist system designed for use on the rear bumper of most cars and trucks. This system detects any people or objects behind the vehicle using

More information

2011 Infiniti QX Quick Reference Guide

2011 Infiniti QX Quick Reference Guide 21 Infiniti QX Quick Reference Guide 06 11 07 08 12 13 04 09 Behind steering wheel on column 11 05 10 03 14 17 18 19 20 21 15 16 INSTRUMENT BRIGHTNESS control SwITcH* HEADLIGHT AND TURN SIGNAL SwITcH windshield

More information

F3 COMPACT Metal Mine F3 Metal Mine Detector Detector SERVICE MANUAL. Version 1: January 2012 Part No:

F3 COMPACT Metal Mine F3 Metal Mine Detector Detector SERVICE MANUAL. Version 1: January 2012 Part No: F3 COMPACT Metal Mine F3 Metal Mine Detector Detector SERVICE MANUAL Version 1: January 2012 Part No: 4904-0005 Contents 1. Introduction... 3 2. Mechanical & Functional Testing... 4 3. Disassembly & Reassembly

More information

Instruction Manual. Backup Sensor Reversing System RVS-RS103

Instruction Manual. Backup Sensor Reversing System RVS-RS103 Instruction Manual Backup Sensor Reversing System RVS-RS103 RVS Systems, Inc. 2017 TABLE OF CONTENTS System Description............................ 03 Safety Information........................... 04 Before

More information

Main Harness Quantity: 1

Main Harness Quantity: 1 Smart Engine Start INSTALLATION MANUAL Genuine Part # : H001SVA900 Vehicle Model : WRX Kit Contents Service P/N: H001SVA910 Service P/N: H001SVA820 NOT USED NOT USED SES ECU Quantity: 1 Double-sided tape

More information

CHECKLIST & COMPONENTS

CHECKLIST & COMPONENTS Eclipse Compact www.rollershuttercompany.com Tel 0800 6444121 55mm Roller Garage Doors CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape measure Power drill 10mm A/F

More information

Bluefin Led Underwater lights.

Bluefin Led Underwater lights. Bluefin Led Underwater lights. P6N/P6CC Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure optimum performance and

More information

Automated Control Electronics (ACE ) System Operation and Diagnostics

Automated Control Electronics (ACE ) System Operation and Diagnostics Commercial Products Automated Control Electronics (ACE ) System Operation and Diagnostics PART NO. 98962SL This page is intentionally blank. Table of Contents Introduction... 1 Controller Operation and

More information

In-Wall Slide-Out REPAIR KIT MANUAL. Rev: Page 1 In-Wall Repair Kits Manual

In-Wall Slide-Out REPAIR KIT MANUAL. Rev: Page 1 In-Wall Repair Kits Manual In-Wall Slide-Out REPAIR KIT MANUAL Rev: 02.16.2017 Page 1 In-Wall Repair Kits Manual TABLE OF CONTENTS Safety Information 2 Introduction 2 Preliminary Visual Inspection 3 Assembly Removal Procedure 4

More information

Always remember to put your Series 60 LED on charge after use to prolong the life of the high capacity rechargeable battery.

Always remember to put your Series 60 LED on charge after use to prolong the life of the high capacity rechargeable battery. Thank you for purchasing the all new Series 60 LED OPERATION - QUICK START Although the Series 60 is packed full of features it is still simple to use. When the unit is packed down in torch/storage mode

More information

LEXUS LC/LCh CARBON FIBER LOWER GRILLE Preparation

LEXUS LC/LCh CARBON FIBER LOWER GRILLE Preparation Preparation Part Number: PT478-11175-05 Kit Contents Item # Quantity Reqd. Description 1 1 Carbon Fiber Lower Grille Insert 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 2 3 Additional

More information

4 Sensor Backup Obstacle Sensing System Model: ACAB104 Users Manual

4 Sensor Backup Obstacle Sensing System Model: ACAB104 Users Manual 4 Sensor Backup Obstacle Sensing System Model: ACAB104 Users Manual 0 5 10 Features: Four reversing sensors detect obstacles between 1-7 feet Includes 0, 5, and 10 angle sensor sleeves to fit most bumpers

More information

O5 GENERAL VEHICLE ISSUES

O5 GENERAL VEHICLE ISSUES O5 GENERAL VEHICLE ISSUES O5.1 GENERAL O5.1.1 Production vehicles are rarely suited to site work in their standard form, so before purchasing a vehicle, consideration should be given to the model s suitability

More information

ED BWS. Back Warning System. 1 Chonan Technical Service Training Center

ED BWS. Back Warning System. 1 Chonan Technical Service Training Center Back Warning System 1 Chonan Technical Service Training Center Chonan Technical Service Training Center 2 Objectives To understand the concept of back warning system. To understand the function of back

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n

More information

MOUNTING RAILS ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***

MOUNTING RAILS ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** 10/30/2017 PAGE 1 OF 6 Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 CM-16150-MR MOUNTING RAILS 2 2 CM-16150-FB.375" FRONT BRACKET 3 1 CM-16150-PSRB.375" PASSENGER SIDE REAR BRACKET 4 1 CM-16150-DSRB.375"

More information

mygrid Installation Notes

mygrid Installation Notes mygrid Introduction mygrid kits provide an easy to install, compliant, Solar Hybrid (On-Grid) or Off-Grid battery system. These installation notes outline all the processes required to effectively install

More information

Operators Guide: RoboSign Stop/Go Traffic Control System

Operators Guide: RoboSign Stop/Go Traffic Control System Operators Guide: RoboSign Stop/Go Traffic Control System RoboSign Remote controlled Stop/Go temporary traffic control system Operators Guide NZTA Conditions - Automated Stop/Go Traffic Control System NZTA

More information

Hydraulic Motorcycle Lift. Model CML3 & CML3 AIR Part No: ASSEMBLY & OPERATING INSTRUCTIONS 0212

Hydraulic Motorcycle Lift. Model CML3 & CML3 AIR Part No: ASSEMBLY & OPERATING INSTRUCTIONS 0212 Hydraulic Motorcycle Lift. Model CML3 & CML3 AIR Part No: 7610143 ASSEMBLY & OPERATING INSTRUCTIONS 0212 DO NOT ENTER UNDER THE PLATFORM UNLESS IT IS MECHANICALLY LOCKED (see instructions) DO NOT EXCEED

More information

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag. Part Number: 343870 F/Kit 17557 Product Deluxe Combination Winch and Non Winch Bull Bar Description: Suited to Nissan XTERRA 05ON USA Only vehicle/s: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG;

More information

AutoScan Satellite System LP

AutoScan Satellite System LP AutoScan AutoScan Satellite System 9630 9630-LP Installation and Operating Instructions Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920

More information

TE-BSM User Manual. l ::: J TECH SUPPORT. MetraDealer.com

TE-BSM User Manual. l ::: J TECH SUPPORT. MetraDealer.com TE-BSM User Manual ibeamusa.com MetraDealer.com techsupport@metra-autosound.com TECH SUPPORT l ::: J 800-253-8324 Features The TE-BSM Blind Spot Monitor is designed with the latest microwave technology

More information

PRODUCT INSTALLATION GUIDE

PRODUCT INSTALLATION GUIDE PRODUCT INSTALLATION GUIDE MODEL: PRODUCT CODE: PRODUCT DESCRIPTION: 4COMM 4COMMSFK CouplerTec Commercial Heavy Duty Electronic Rustproofing System 12V / 24V Four Capacitive Couplers KIT CONTENTS: ITEM

More information

SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine)

SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine) SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine) 21/7/2010 Parts List ITEM PART NO DESCRIPTION QTY 1 570-133-200 BODY - SNORKEL (SS41HF)

More information

Lighting GENERAL INFORMATION. Daytime running lamps. Halogen headlamps. Stop lamps. Bi-Xenon headlamps. Reversing lamps

Lighting GENERAL INFORMATION. Daytime running lamps. Halogen headlamps. Stop lamps. Bi-Xenon headlamps. Reversing lamps Lighting GENERAL INFORMATION There are three types of headlamp systems: Halogen high/low beam main lamp with a fill-in high beam halogen lamp alongside. Bi-xenon high/low beam main lamps with fill-in high

More information

Quick GUIDE Web edition

Quick GUIDE Web edition s60 Quick GUIDE Web edition WELCOME TO YOUR NEW VOLVO! Getting to know your new car is an exciting experience. Take a look at this Quick Guide to learn some of the most common functions quickly and easily.

More information

Series 1000 and Cutout

Series 1000 and Cutout 17.15.Remove the belt from the tractor. NOTE: There were a small number of tractors made using a CVT drive and a 2-speed (L-H-N-R) GT transaxle. The belt must pass over the center mounted gear selector

More information

TFL Gas Log Lighter (TFLGLL)

TFL Gas Log Lighter (TFLGLL) TFL Gas Log Lighter (TFLGLL) For Jetmaster Metal Fireboxes and Logpans CONTENTS Description Page No. Important information 2 Operation and Design 3 Controller Solenoid Cavity 4 Contents of a Kit 5 To install

More information

Introduction...3. System Overview...3. PDC Control Unit Sensors PDC Button Interfaces Activation of the PDC...

Introduction...3. System Overview...3. PDC Control Unit Sensors PDC Button Interfaces Activation of the PDC... meeknet.co.uk/e64 Table of Contents PARK DISTANCE CONTROL (PDC) Subject Page Introduction...............................................3 System Overview...........................................3 Components

More information

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:

More information

Eaton VORAD Always Alert/SmartCruise/BlindSpotter. More time on the road. Driver Instructions

Eaton VORAD Always Alert/SmartCruise/BlindSpotter. More time on the road. Driver Instructions Eaton VORAD Always Alert/SmartCruise/BlindSpotter More time on the road Driver Instructions Eaton VORAD Always Alert/SmartCruise/BlindSpotter VODR0035 October 2007 Warnings and Cautions Warnings and Cautions

More information

EXOTHERMIC CUTTING EQUIPMENT

EXOTHERMIC CUTTING EQUIPMENT EXOTHERMIC CUTTING EQUIPMENT Objectives By the end of this session, you will be able to: Identify the difference between the Arcair packages that are available to EU customers. Recognise the main components

More information

Operating Instructions. TEK 678 Display Unit with remote and 10 bar display

Operating Instructions. TEK 678 Display Unit with remote and 10 bar display Operating Instructions TEK 678 Display Unit with remote and 10 bar display V1/072017 Contents 1 Introduction... 3 2 Contents of Package... 3 3 Fuel and Tank Types... 3 3 Preparing the Tank... 3 4 Define

More information

All Bluefin Led lights are water tested so please be aware there may be moisture present on the light.

All Bluefin Led lights are water tested so please be aware there may be moisture present on the light. Bluefin LED Underwater lights. GW16IFM/GW20IFM/GW48CCIFM Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested to ensure optimum performance

More information

WWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER

WWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER WWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER Notice. Please read these instructions carefully before installing the Rolling Door motor 1. The motor must be installed and operated by a professional.

More information

Installation Guide Rollerdor RD55 Econ Roller Garage Door

Installation Guide Rollerdor RD55 Econ Roller Garage Door Installation Guide Rollerdor RD55 Econ Roller Garage Door 1 Finished door Rollerdor RD55 Econ Roller Garage Door CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape

More information

WARNING!! C-659 SUBKIT FIGURE 4

WARNING!! C-659 SUBKIT FIGURE 4 '0-'0 DODGE / TON TRUCKS '03-' DODGE 3/ & TON TRUCKS (WILL FIT /, 3/ & TON MEGA CAB SHORT BED) WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR

More information

INSTALLATION GUIDE Ultrasonic Sensors Series UX micro

INSTALLATION GUIDE Ultrasonic Sensors Series UX micro INSTALLATION GUIDE Ultrasonic Sensors Series UX micro For further information please see the data sheet at www.waycon.biz/products/ultrasonic-sensors/ FIRST STEPS WayCon Positionsmesstechnik GmbH would

More information

LIGHTNING PLUS 120 WATT / 6 OUTLET VOLT POWER SUPPLY & STROBE LIGHT KIT 6 Different Light Patterns 8006 SERIES INSTALLATION INSTRUCTIONS

LIGHTNING PLUS 120 WATT / 6 OUTLET VOLT POWER SUPPLY & STROBE LIGHT KIT 6 Different Light Patterns 8006 SERIES INSTALLATION INSTRUCTIONS LIGHTNING PLUS 120 WATT / 6 OUTLET 12-24 VOLT POWER SUPPLY & STROBE LIGHT KIT 6 Different Light Patterns 8006 SERIES INSTALLATION INSTRUCTIONS Your purchase of Wolo s LIGHTNING PLUS strobe light system

More information

Crossrail Vehicle Safety Equipment Supplementary Guidance. Works Information Ref:

Crossrail Vehicle Safety Equipment Supplementary Guidance. Works Information Ref: FRESNEL Lens RHD & LHD Vehicles Ref: 26.14.8 1 of 10 Product Description The Fresnel Lens is a visual device for lorry drivers and is not a mirror in the conventional sense. It is a clear thin plastic

More information

Montage- und Bedienungsanleitung

Montage- und Bedienungsanleitung Montage- und Bedienungsanleitung Installation and Operating Instructions Instrucciones de montaje y de servicio Instructions de montage et de service Istruzioni di montaggio e d uso Montage- en bedieningshandleiding

More information

Bluefin Led Underwater lights.

Bluefin Led Underwater lights. Bluefin Led Underwater lights. P3 Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure optimum performance and longevity.

More information

CPCS renewal test factsheet

CPCS renewal test factsheet CPCS renewal test factsheet Introduction to the CPCS renewal test The industry-led CPCS Management Committee has determined that key safety-related knowledge must be checked on each category prior to the

More information

ASNU Battleship MK2 Fitting Instructions

ASNU Battleship MK2 Fitting Instructions ASNU Battleship MK2 Fitting Instructions You will be required to disassemble certain parts from the stock fuel system and then integrate them into the battleship before reinstalling the system into the

More information

RPM Inductive XENON TIMING LIGHT

RPM Inductive XENON TIMING LIGHT RPM Inductive XENON TIMING LIGHT PART NO G4132 HANDBOOK RPM Inductive INDEX Page 1. XENON TIMING LIGHT 2 2. PRINCIPLE OF OPERATION 2 3. IMPORTANCE OF IGNITION TIMING 3 4. USE OF UNLEADED PETROL 3 5. TIMESTROBE

More information

OXFORD. OF690 Adventure. OF691 Touring. OF692 Sports. Page 2-7. v.8 switch 09/07/12

OXFORD.   OF690 Adventure. OF691 Touring. OF692 Sports. Page 2-7. v.8 switch 09/07/12 OXFORD Page 2-7 Page 8-13 Page 14-19 Page 20-26 OF690 Adventure Page 27-32 Page 33-39 OF691 Touring OF692 Sports www.oxprod.com v.8 switch 09/07/12 Oxford HotGrips : Fitting and User Instructions for part

More information

Ag Leader Technology. Combine Installation New Holland TC 57, 59. Monitor Installation

Ag Leader Technology. Combine Installation New Holland TC 57, 59. Monitor Installation Monitor Installation Figure 1. Monitor installed on right side cab window using window mount bracket. 1. If you are in very humid conditions where moisture may condense on the glass where you are mounting

More information

INSTALLATION INSTRUCTIONS:

INSTALLATION INSTRUCTIONS: INSTALLATION INSTRUCTIONS: The CA-5010.II is an ultrasonic parking assist system designed for use on the rear bumper of most cars and trucks. This system detects any people or objects behind the vehicle

More information

Package Contents. Mounting Hardware

Package Contents. Mounting Hardware Securitron Magnalock Corp. www.securitron.com Tel 800.624.5625 techsupport@securitron.com M680BDCX MAGNALOCK SERIES Installation Instructions Table of Contents Specifications 2 Configuring Options 3 Installation

More information