Verax 75 and Verax VPA Installation Manual

Size: px
Start display at page:

Download "Verax 75 and Verax VPA Installation Manual"

Transcription

1 Verax 75 and Verax VPA Installation Manual JP3 Measurement 4109 Todd Lane Austin TX

2 Table Of Contents: 1. Facilities Requirements page 3 2. Unpacking and Handling page 5 3. Mounting the Control Panel page 7 4. Mounting the Probe Assembly page 9 5. Probe Assembly to Control Panel Connections page Z-purge installation (optional) Page Heater Blanket for Probes (optional) Page Power Up and Commissioning Page

3 1) Facilities Requirements: Intended Use: The Verax 75 is an optical NIR analyzer for determining the constituents and physical properties of a hydrocarbon fluid stream by using NIR spectroscopy to model the parameter of interest. Contact a JP3 sales representative to discuss the range of analysis available. The Verax 75-Z model incorporates a Z-purge system for mounting in a Class I / Division 2 location. Location Rating: Verax 75 Analyzer is in a Type 4 NEMA Enclosure, and all provided fittings are Type 4 rated. For General Purpose Location, Conforms to ANSI/UL Std For Class I / Division 2 A,B,C,D, T Code- T4 a Type Z- pressurization must be used. With Z-purge, Conforms to NFPA Std 496 Certified to CAN/CSA Std C22.2 No Operational temperature range: -29C to 50C (-20⁰ F to 122⁰F). Electrical Input Requirements: Per Customer Specification one of the two options below: V AC, Hz, Amp Or, 24V DC, 3.5 Amp The input electrical configuration is indicated on the warning tag below the antenna on the left side of the box (see Figure 3) For surge protection a 20A breaker is recommended as the customer-provide disconnection device Other Facilities Requirements (for Z-purge only): Instrument Air or Nitrogen Supply pressure: psig Safe Pressure Set Point: 0.25 water column Safe pressure flow rate: SCFH Exchange Flow Rate: 4 SCFH 3

4 Explanation of Warning Labels: The following warning applicable only when using the Z-purge option: WARNING PRESSURIZED INCLOSURE This enclosure must not be opened unless the area atmosphere is known to be below the ignitable concentration of combustible materials or unless all the devices within have been de-energized AVERTISSEMENT : BOÎTIER SOUS PRESSION: Ce boîtier ne doit pas être ouvert à moins que l'atmosphère de la zone ne soit inférieure à la concentration inflammable de matières combustibles ou à moins que tous les dispositifs qui s y trouvent n aient été mis hors tension. The following warning applicable only when using the Z-purge option: WARNING: Power must not be restored after enclosure has been opened and until enclosure has been purged for 3.5 minutes for Verax 75-Z model or 6 minutes for Verax 75M-Z AVERTISSEMENT: L'alimentation ne doit pas être rétablie après l ouverture du boîtier et jusqu'à ce que le boîtier ait été purgé pendant 3,5 minutes pour le modèle Verax 75-Z ou 6 minutes pour le modèle Verax 75M-Z. The following warning applicable to all models: The model and electrical configuration on the warning label are specified with punched holes next to the applicable value. Le modèle et la configuration électrique sur l'étiquette d'avertissement sont spécifiés avec des trous percés à côté de la valeur applicable Figure 1: Warning Label Located on the left side of the analyzer below the antenna port. (see Figure 3) 4

5 2) Unpacking and Handling: Shipped Materials: Verax Analyzer Control Panel (qty 1) Probe Assembly (qty 1) Antenna (qty 1) Z-purge w/ fittings (optional, 1 set) Handling Instructions: Weight: 51lbs Dimensions: 24 x 30 x 9.35 Mounting Holes: 18 x Uncrate and mount the analyzer to unistrut or other mounting surface capable of handling the weight of the unit. Do not drop Front View Side View Figure 2 Verax 75 Analyzer Control Panel - Dimensions 07/01/2015 Verax Single ChInstallation Manual, Rev H 5

6 Antenna Fitting Wiring Terminal Blocks Incoming Power Connection Serial # & Warning Label Radio / Modem PC PLC Ethernet Switch (Comm) RTD and Transducer Terminal Block Spectrometer Figure 3 Verax 75 Analyzer Control Panel Front View 6

7 3) Mounting the Control Panel: Mounting Requirements: Select a location that is easily accessible at grade level. Mounting holes are provided for easy installation. The Probe Assembly must be mounted next to the analyzer separation is limited by 10 linear feet of fiber. Shade is required if mounting outdoors where ambient temps can exceed 90⁰ F. Do not mount the analyzer in such a way to make it difficult to operate the customer-provided electrical disconnect device (witch, breaker or other) Antenna Connection: 1. 16dB Antenna is provided along with a 90 degree fitting. 2. Attach Antenna to the fitting on the upper left of the Analyzer Panel using the 90 degree fitting (see Figure 3 for location of the fitting). 1. Fiber Optic Connection: 2. The Fiber is passed through the flex conduit/liquid tight fittings on the bottom of the analyzer control panel. Customer provides flex conduit. 3. Send Fibers will be labeled with 2 Red Shrink Tube reading SEND. 4. Receive Fibers will be labeled with 2 Yellow Shrink Tube reading RECEIVE. 5. Pull the fibers through the flex conduit, and let the excess hang coiled up under the analyzer until ready to connect to the probe assembly. 6. Leave the caps on the end of the fiber. Do not let the fiber drag on the ground. 7. See Section 5 for instructions to connect the fiber to the probe assembly Figure 4 Fiber Optic Cables installed with the Liquid Tight Fitting and Flex Conduit 7

8 Pass-through for Electrical Wires: The Verax Control Panel is shipped without holes or wire ways for most of the incoming electrical service or fiber connections. The only pre-positioned holes are: The Antenna fitting (top left), and Two fittings for the fiber (bottom left) Additional wire pass-throughs will need to be installed by the customer. The placement of these holes is left up to the customer s installation teams in order to provide maximum flexibility to bring the cables and fiber from below or above, and attach them to the Verax Control Panels with a sufficient size conduit or fitting. All connections or fittings chosen by the customer should by rated for Type 4 enclosure. After the wires and fibers are run, all ports and pass-throughs must be plugged with duct putty or some other standard industry practice to assure the sealed integrity of the enclosure. The customer must plan for the following cables when choosing the size and placement of ports on the Verax Control Panel: One Incoming Electrical Cable One Incoming communications Cable One RTD cable from the probe assembly One Transducer cable from the probe assembly Read instructions in Section 6 regarding where these fibers/cables attach inside the control panel before you start cutting holes. The customer is responsible to protect the inside of the control panel when cutting or punching holes for the wire way. DO NOT ALLOW METAL SHAVINGS TO FALL ON THE ELECTRICAL CONNECTIONS OR COMPONENTS INSIDE THE CONTROL PANEL. Contact your local JP3 sales representative to discuss options 8

9 4) Mounting the Probe Assembly: Placement: The Probe Assembly are typically mounted to a unistrut frame, or other solid structure Probes should be accessible at grade level. Pressure and Temp Rating: All probe windows and probe assemblies are tested to 1500 psi Operational temperature range: -29C to 50C (-20⁰ F to 122⁰F). Bypass Probe Configuration: For a bypass probe assembly, the customer taps into the process stream they want to monitor, plumbs the fluid to the inlet on probe assembly, and back to the process stream. (see Figure 4 on the next page) It is highly recommended that the customer supply a stinger at the inlet and return of the pipe you are monitoring in order to pull fluid from the center of the pipe. Either ½ or ¼ Swagelok fittings are supplied on the inlet and return ports of the probe assembly. Customer supplies ¼ or ½ stainless steel tubing as dictated by the fittings supplied on the probe assembly. ½ is typical for liquids ¼ is typical for gas The customer must assure sufficient flow of liquid or gas over the probe windows by providing a pressure drop of at least 2 inaq (or 20 SCFH) from inlet to outlet. Choosing the correct inlet and return points on the process pipe is critical to assure flow. Often choosing inlet and return points such that flanges, valves, meters or similar instruments are located between these two points is sufficient to provide the necessary bypass pressure differential. Actual Installation details vary by location and application; consult with JP3 Sales representative to discuss options. When using a heater blanket with the probe assembly, 120VAC, 2 Amp service is required. The junction box must be within 4 feet of the probe assembly. 9

10 P from Inlet to Return must be at least 2 inaq (inches of water) Inlet Stinger to sample from center of the pipe Return Figure 5 Example Probe Bypass Arrangement Receive Fiber Sealcon Fitting Inlet Port Transducer 21 RTD Service Port DO NOT REOME CAP Send Fiber Sealcon Fitting 13.2 Service Port DO NOT REMOVE CAP Return Port Conduit Housing 4.4 Top-Down View Figure 6 Bypass Probe Assembly 10

11 5) Probe Assembly to Control Panel Connections Connect Fiber Optics to Probe Assembly: Warning Read Carefully Fiber optic cable is extremely sensitive to sharp bend angles and contamination. Handle very carefully to avoid kinks and keep the ends capped until ready to attach to the probes. Maintain a minimum 7 bend radius when running/routing the fiber from control box to probe assembly It is recommended that the fiber optic cable be run in it s own dedicated conduit, or elevated cable trays. Do not place fiber in ground level open cable trays where it can be stepped on. Keep the fiber ends capped until you a are ready to connect the ends. Attach Fiber to Probe Assembly: 1. Open the conduit housing on the probe assembly 2. Install the fiber using LT50 fittings and flex conduit at either end of the probe assembly (see Figure 6). The flex conduit approach offers the best protection for the fiber. 3. Connect the fiber to the back of the probe inside the conduit housing by screwing the fiber end onto the threaded probe connection. (see Figure 7) 4. DO NOT THROW AWAY THE KNURLED CAPS. These should be left in the conduit housing to be used to protect fiber and probe connections when disconnected during servicing. 5 Replace conduit housing cover Liquid Tight Fitting Figure 7 Fiber Installation on Probe Assembly Fiber/Probe Connection Point 11

12 JP3 Measurement Fiber Optic Cable Specification JP3 uses a custom optical fiber assembly, design and characterized to maximize the characteristics of the optical loop from laser to probe and back to the detector. The following are specifications important for handling and installation of the fiber: 600um-core multimode fiber with a Kevlar jacket. 5.5mm black PVC weather proof furcation jacket, UV resistant Outdoor rated construction, and all components nonconductive (most similar to OFNR indoor construction) Weight = 22 lbs/1000 feet Max Installation Tension, 180 lbs (800N) Max Operating Tension, 90 lbs (400N) Installation Temp Range, 15⁰ F to 176⁰ F (-20 to 80 C) Operational temp range, -20⁰ F to 122⁰ F (-29C to 50C) Minimum Bend Radius = 7 Male SMA connections on both ends. Each end will be labeled as below: Figure 8 Fiber Assembly dimensions and labeling 12

13 Wire the Probe Assembly to the Control Panel: 1. The Analysis Points on the RTD and Transducer terminals are numbered 1-2 from top to bottom 2. Run the RTD and transducer cables through customer-provide wire pass through port and route to the terminal blocks on the left side of the panel. 3. Connect the RTD cable to number 1 on the RTD terminal block, as shown in Figure 9: one red wire to the top terminal tier the other red wire to the middle terminal tier the white wire to the bottom terminal tier 4. Connect the transducer cable to number 1 on the transducer terminal block as shown in Figure 9: Red wire on the top terminal tier Black on the second terminal tier Brown on the third terminal tier Gray on the bottom terminal tier Figure 9 RTD and Transducer Wiring Instructions 13

14 Connect the Ethernet Communications Cable: 1. Run the Ethernet communications cable through customer-provide wire pass through and route to the Ethernet switch on the right side of the analyzer control panel. ( See Figure 3) 2. Connect to any available Ethernet port Connect Main Power: For 24V DC Power Configuration 1. Run the power cable through customer-provide wire pass through port and route to the terminal blocks on the upper right side of the analyzer control panel. ( See Figure 3) 2. Connect hot wire to 24V fuse 3. Connect neutral wire to 0V terminal Figure 10 Main 24VDC Power Wiring Instructions Components shown inside dotted line only included with v AC option 14

15 Connect Main Power: For VAC Power Configuration 1. Run the power cable through customer-provide wire pass through port and route to the terminal blocks on the upper right side of the analyzer control panel. ( See Figure 3) 2. Connect hot wire to V fuse 3. Connect neutral wire to 0V terminal 4. Connect ground wire to the green/yellow ground terminal Figure 11 Main VAC Power Wiring Instructions Components shown inside dotted line only included with v AC option 15

16 6) Z-Purge Installation (optional): Warning Read Carefully You must install the Z-purge if the Verax 75 will be in a Class I / Division 2 Hazardous location. Installation: Mounting Configuration and Pipe Routing are shown below in Figures 11 and 12. All fittings are ¼ Figure 12 Pipe Fitting Schematic, (Viewed from back of Verax Panel) 16

17 Figure 13 Z-Purge Hardware Configuration. 17

18 7) Probe Heater Blanket (optional): Installation: Heater blankets are designed to wrap around the sample cell cross to keep the probes warm and free of paraffins. Electrical: Heater blankets use Thermon self-regulating 12W/ft heating tape 2Amp, 120V AC electrical service A 5 pigtail is provided using ½ flex conduit. Figure 14 Heater Blanket 18

19 8) Power-up and Commissioning: Power Up Sequence: To Engage Power engage the fuses in the following order V fuse (if applicable for the AC configuration only) 2. 24V fuse (Power to PLC, Switch) 3. 12V fuse (Powers PC and Radio) 4. 12V fuse (Powers Spectrometer) Figure 15 Power up sequence 4th 3rd 2nd 1st At this point the Verax 75 Analyzer is ready to be commissioned. Contact JP3 Field Service team to complete installation and commissioning. Contact JP3 Field Service team for all maintenance and servicing needs

READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER RISK OF SHOCK DISCONNECT POWER BEFORE INSTALLATION

READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER RISK OF SHOCK DISCONNECT POWER BEFORE INSTALLATION UR Series LED Upgrade Kit Includes: 24" Linear Option IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL

More information

IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:

IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: ZR-RK Series LED Retrofit Troffer Kit Includes: ZR22RK and ZR24RK Standard and Emergency Luminaires IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed

More information

TubeTrace Tubing Bundles

TubeTrace Tubing Bundles for Custom CEMS and Analytical Umbilicals English Units Receiving, Storing and Handling... 1. Inspect materials for damage incurred during shipping. Report damages to carrier for settlement. 2. Identify

More information

Spun Bay Installation Standard Version (non dimmable), Hook Mount

Spun Bay Installation Standard Version (non dimmable), Hook Mount Spun Bay Installation Standard Version (non dimmable), Hook Mount WARNING: Make sure that all power is turned off while installing fixture. Do not turn power on until fixture is completely installed. Turn

More information

MOONRING 1.5 MOONRING 3

MOONRING 1.5 MOONRING 3 INSTALLATION INSTRUCTIONS MOONRING 1.5 MOONRING 3 MR1.5 & MR3 Suspended, Ceiling LED n A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings!

More information

INSTALLATION INSTRUCTIONS MOONRING 1 LP1/MR1

INSTALLATION INSTRUCTIONS MOONRING 1 LP1/MR1 INSTALLATION INSTRUCTIONS MOONRING 1 LP1/MR1 Suspended, Ceiling LED n A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.

More information

SloanLED THINLED. Constant Current. Installation Guide

SloanLED THINLED. Constant Current. Installation Guide SloanLED THINLED Constant Current Installation Guide Product covered in this guide: ThinLED CC: Part Number Description 701228-18-A Amber ThinLED Constant Current 701228-18-B Blue ThinLED Constant Current

More information

VA-4233-AGx Series Electric Valve Actuators

VA-4233-AGx Series Electric Valve Actuators Installation Instructions VA-4233 No. 1 Issue Date June 30, 2014 VA-4233-AGx Series Electric Valve Actuators Installation Refer to Figures 2 through 4 for proper actuator orientation before attempting

More information

Power Connection Kit installation instructions

Power Connection Kit installation instructions Operating instructions & Parts Manual ET00 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and

More information

BITZER Capacity Controller for CSH Compressors Temperature Sensor

BITZER Capacity Controller for CSH Compressors Temperature Sensor only. The Temperature Controller has been obsoleted. The below data is for informational purposes only BITZER Capacity Controller for CSH Compressors Temperature Sensor The BITZER CSH Capacity Controller

More information

INSTALLATION INSTRUCTIONS FOR Owner's Copy FILTERED AND REGULATED POWER SUPPLY VOLTS DC INPUT: Hz.

INSTALLATION INSTRUCTIONS FOR Owner's Copy FILTERED AND REGULATED POWER SUPPLY VOLTS DC INPUT: Hz. 103158 March 9, 2011 FOR INDOOR USE ONLY Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045 (830)629-2900 / 1-800-729-3839 / Fax (830)620-6711 E-MAIL: detex@detex.com INTERNET: www.detex.com

More information

Flow Computer Installation

Flow Computer Installation Flow Computer Installation WARNING: Only personnel who are experienced with field wiring should perform these procedures. All field wiring must conform to the National Electrical Code, NFPA 70, Article

More information

ClassicSeries Compressor Installation

ClassicSeries Compressor Installation ClassicSeries Compressor Installation Applies to Models: CL21-115 Volts CL22, CL32, CL52-208- 230 Volts Equipment Alert Compressor system must be installed per local plumbing and electrical codes. Note:

More information

Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series)

Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) GE Lighting Installation Guide Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) Features UL 1598 Suitable for Wet Locations IP66 Rated Ingress Protection BEFORE YOU BEGIN Read these

More information

Wet Rated Batten LED Luminaire

Wet Rated Batten LED Luminaire Installation Guide Wet Rated Batten LED Luminaire LED Lighting System BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING / AVERTISSEMENT RISK OF ELECTRIC SHOCK Turn power off before

More information

MODELS 2 & 4 Top Conduit Linears

MODELS 2 & 4 Top Conduit Linears INSTALLATION AND MAINTENANCE MANUAL SAFESITE AND DUROSITE LED LINEAR FIXTURE Document No: 9100-127-1885-99 Rev E December, 2016 MODELS 2 & 4 Top Conduit Linears These instructions contain important safety

More information

Lumination TM LED Luminaires LAL Series - Continuous Run Option

Lumination TM LED Luminaires LAL Series - Continuous Run Option GE Lighting Installation Guide Lumination TM LED Luminaires LAL Series - Continuous Run Option BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC

More information

GVB-8 (Boost) Manual

GVB-8 (Boost) Manual www.genasun.com GVB-8 (Boost) Manual Solar Charge Controllers with Maximum Power Point Tracking For models: GVB-8-Pb-12V: 12V Lead-Acid/AGM/Gel/Sealed/Flooded GVB-8-Pb-24V: 24V Lead-Acid/AGM/Gel/Sealed/Flooded

More information

GV-10 Manual 10.5A / 140W IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. Solar Charge Controllers with Maximum Power Point Tracking

GV-10 Manual 10.5A / 140W IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. Solar Charge Controllers with Maximum Power Point Tracking GV-10 Manual Solar Charge Controllers with Maximum Power Point Tracking For models: GV-10-Pb-12V: GV-10-Pb-CV: 12V Lead-Acid/AGM/Gel/Sealed/Flooded 12V Custom Multi-Stage Lead-Acid/AGM/Gel/ Sealed/Flooded

More information

Cable Cubby 1202 and 1402 Installation Guide

Cable Cubby 1202 and 1402 Installation Guide Cable Cubby 0 and 40 Installation Guide IMPORTANT: Go to www.extron.com for the complete user guide, installation instructions, and specifications. This guide provides instructions for an experienced technician

More information

CSD Series Current Devices Split Core

CSD Series Current Devices Split Core CSD Series Current Devices Split Core Installation Instructions CSD-CF0A0-1 CSD-CF0J0-1 CSD-CA1G0-1 Part. 24-10345-34, Rev. D Issued March 31, 2014 Supersedes April 5, 2013 Applications The Current Switch

More information

PowerAir Compressor Installation

PowerAir Compressor Installation PowerAir Compressor Installation Applies to Models: P21-115 Volts P22, P32-230 Volts P52, P72-230 Volts Equipment Alert Compressor system must be installed per local plumbing and electrical codes. Model

More information

INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5. LP3.5 Suspended LED. A nd Avenue, Unit 1. CA P E W alwusa.

INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5. LP3.5 Suspended LED. A nd Avenue, Unit 1. CA P E W alwusa. Oakland, INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5 LP3.5 Suspended LED A 1035 22nd Avenue, Unit 1 n CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.

More information

FAIRCHILD T5200 SERIES ELECTRO-PNEUMATIC TRANSDUCER Installation, Operation and Maintenance Instructions

FAIRCHILD T5200 SERIES ELECTRO-PNEUMATIC TRANSDUCER Installation, Operation and Maintenance Instructions FAIRCHILD T500 SERIES ELECTRO-PNEUMATIC TRADUCER Installation, Operation and Maintenance Instructions Identification Number Underwriting Group Factory Mutual Canadian Standard T (F) (C) 500- Approval Class

More information

MODELS. 2 & 4 Low Profile Linears

MODELS. 2 & 4 Low Profile Linears INSTALLATION AND MAINTENANCE MANUAL SAFESITE LED LINEAR FIXTURE Document No: 9100-127-2182-99 Rev D December, 2016 MODELS 2 & 4 Low Profile Linears These instructions contain important safety information,

More information

SAVE THESE INSTRUCTIONS

SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be

More information

LAL SERIES LED LUMINAIRE

LAL SERIES LED LUMINAIRE INSTALLATION, OPERATION & MAINTENANCE DATA SHEET LAL SERIES LED LUMINAIRE CAUTION: LAL SERIES LED LUMINAIRE Before installing, make sure you are compliant with area classifications, failure to do so may

More information

Single-Phase Step Voltage Regulators

Single-Phase Step Voltage Regulators Voltage Regulators Catalog Data CA225001EN Supersedes March 2017 COOPER POWER SERIES Single-Phase Step Voltage Regulators Contents GENERAL....2 STANDARD FEATURES....4 OPTIONAL ACCESSORIES...4 ARRESTERS....4

More information

Lumination TM LED Luminaire RC/LRC/RX/LRX Series - New Construction Frame

Lumination TM LED Luminaire RC/LRC/RX/LRX Series - New Construction Frame Installation Guide Lumination TM LED Luminaire RC/LRC/RX/LRX Series - New Construction Frame BEFORE YOU BEGIN Read these instructions completely and carefully. RISK OF ELECTRIC SHOCK Turn power off before

More information

I. Pendant Mount Installation

I. Pendant Mount Installation LED HIGH BAY MAX Luminaires for High Bay Applications HBM SERIES IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: 1 THIS

More information

INSTALLATION INSTRUCTIONS LED Canopy Retrofit Kit

INSTALLATION INSTRUCTIONS LED Canopy Retrofit Kit INSTALLATION INSTRUCTIONS LED Canopy Retrofit Kit TRMUNV065ECxyyZ TRAUNV065ECxyyZ Installation Instructions subject to change without notice. Page 1 of 8 1.0 INSTALLATION WARNINGS 1. 2. 3. 4. 5. 6. "THIS

More information

RAPID SHUTDOWN COMBINER

RAPID SHUTDOWN COMBINER RAPID SHUTDOWN COMBINER Installation and Operation Guide Revision B 2017, Yaskawa Solectria Solar IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 1. General Safety Information This manual contains

More information

INSTRUCTION BOOK FOR. Dual Masking Electrol

INSTRUCTION BOOK FOR. Dual Masking Electrol INSTRUCTION BOOK FOR Dual Masking Electrol Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand

More information

Installation Instructions

Installation Instructions Accessory Ultra-Violet Germicidal Lamps 40RM007-034, 40RMQ008-016 and 40RMS008-024 Air Handler Units Installation Instructions Part Numbers: CRDBLFIX001A00, CRDBLFIX002A00, CRDBLFIX003A00, CRDBLFIX004A00,

More information

COLUMN DESCRIPTIONS AND FUNCTIONS: COL # LENGTH TUBING TYPE COLUMN DESCRIPTION L1-1A 5M METAL CAP 1.0um MXT-WAX MM METAL CAP L1-1B 60M METAL CAP

COLUMN DESCRIPTIONS AND FUNCTIONS: COL # LENGTH TUBING TYPE COLUMN DESCRIPTION L1-1A 5M METAL CAP 1.0um MXT-WAX MM METAL CAP L1-1B 60M METAL CAP COLUMN DESCRIPTIONS AND FUNCTIONS: COL # LENGTH TUBING TYPE COLUMN DESCRIPTION L1-1A 5M METAL CAP 1.0um MXT-WAX - 0.53MM METAL CAP L1-1B 60M METAL CAP 1.5um MXT-1-0.53MM METAL CAP FUNCTION OF COLUMN COMPLETES

More information

F-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide

F-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide F-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide 11451 Belcher Road South, Largo, FL 33773 USA Tel +1 (727) 447-6140 Fax +1 (727) 442-5699 1054-7 / 34405 www.onicon.com sales@onicon.com

More information

MODELS SafeSite LED Linear, Class I Div V, 2 & 4 Versions

MODELS SafeSite LED Linear, Class I Div V, 2 & 4 Versions INSTALLATION AND MAINTENANCE MANUAL SAFESITE LED LINEAR FIXTURE Document No: 9100-127-1622-00 Rev E December, 2016 MODELS SafeSite LED Linear, Class I Div. 1 347-480V, 2 & 4 Versions All the above Models

More information

Switchgear Skid, C1192

Switchgear Skid, C1192 CUSTOM SOLUTIONS 15kV Modular Stairs stored on floor in front of battery bay Ground grid stored on front tongue of trailer Stairs deployed for unit access Storage box for fencing materials and other parts

More information

poollux Power plx-pw60 & plx-pw100

poollux Power plx-pw60 & plx-pw100 poollux Power plx-pw60 & plx-pw100 ETL LISTED Conforms to UL STD 379; Certifi.ed.to.CSA.STD.C22.2.#218.1 5005508 Installation Instructions Read all instructions before attempting to perform installation

More information

Operating Instructions

Operating Instructions DuroSite & SafeSite Area Light with Adapters Important Information: These instructions contain safety information, read and follow them carefully. Dialight will not accept any responsibility for injury,

More information

DUST ALERT BinMaster Price Book binmaster.com Subject to change without notice 1

DUST ALERT BinMaster Price Book binmaster.com Subject to change without notice 1 DUST ALERT - 3000 BinMaster Price Book 01-2019 binmaster.com Subject to change without notice 1 DUST ALERT - 3000 Dust Alert - 3000 The Dust Alert with integrated electronics and sensing probe utilizes

More information

CYCLOPS Z Purge Indicator

CYCLOPS Z Purge Indicator Low cost Simple to install & use Highly reliable & maintenance free Enclosure vent is part of casing Local & remote status indicator Casing available in anodized aluminum & 316 stainless steel 12 or 24

More information

WARNING/AVERTISSEMENT. Coupez l alimentation électrique à la boîte de fusibles ou au disjoncteur avant servicing or installing product.

WARNING/AVERTISSEMENT. Coupez l alimentation électrique à la boîte de fusibles ou au disjoncteur avant servicing or installing product. Tetra Contour LS LED Lighting System GEXNLBL-1, GEXNLGL-1, GEXNLRD-1, GEXNL65-1, GEXNL32-1 Installation Guide 24 Volt BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT

More information

Replacement Parts List

Replacement Parts List Replacement Parts List PARTS & SERVICE DEPARTMENT Nashville, Tennessee 877-554-5544 Fax: 615-882-2918 parts_team@lochinvar.com www.lochinvar.com Copper-Fin II Boilers Water Heaters CH CF 992-2072 50 17

More information

AIR ZONE INTERNATIONAL MIXED-FLOW AIR COLUMN UNIT

AIR ZONE INTERNATIONAL MIXED-FLOW AIR COLUMN UNIT ZONE INTERNATIONAL MIXED- COLUMN UNIT 5220 TED ST. HOUSTON, TEXAS 77040 (713) 460-4040 FAX (713) 460-4050 WWW.ZONEINC.COM ZONE INTERNATIONAL MIXED- COLUMN UNIT T DUCT COLLAR INLET (A x B) PRIMARY RETURN

More information

GVB-8 (Boost) Manual

GVB-8 (Boost) Manual GVB-8 (Boost) Manual Solar Charge Controllers with Maximum Power Point Tracking For models: GVB-8-Pb-12V: 12V Lead-Acid/AGM/Gel/Sealed/Flooded GVB-8-Pb-24V: GVB-8-Pb-36V: GVB-8-Pb-48V: GVB-8-Pb-CV: 24V

More information

M9109-GGx-5 Series Proportional Electric Non-spring Return Actuators

M9109-GGx-5 Series Proportional Electric Non-spring Return Actuators 34-636- 1360, Rev. C Installation Instructions M9109-GGx-5 Issue Date March 2016 M9109-GGx-5 Series Proportional Electric Non-spring Return Actuators Installation IMPORTANT: Use this M9109-GGx-5 Series

More information

Generator Fire Safety: Generator assemblies should be located outside the building.

Generator Fire Safety: Generator assemblies should be located outside the building. SECTION 33 70 00 - ELECTRICAL DISTRIBUTION PACKAGED GENERATOR ASSEMBLIES Generator Fire Safety: Generator assemblies should be located outside the building. All fuel piping from the outside of the building

More information

IMPORTANT: SAFETY INSTRUCTIONS Important: Instructions de securité

IMPORTANT: SAFETY INSTRUCTIONS Important: Instructions de securité MUV-401H MultiVoltage Germicidal Air Purifier Installation & Maintenance Instructions UNPACKING THE UNIT Each MUV-401H germicidal air purifier is shipped with the germicidal lamp placed in a lamp box.

More information

Specification for Heated Instrument Tubing in Process Applications* (March 29, 2007)

Specification for Heated Instrument Tubing in Process Applications* (March 29, 2007) Specification for Heated Instrument Tubing in Process Applications* (March 29, 2007) 1.0 SCOPE This specification outlines the minimum requirements for electrically traced or steam/fluid traced instrument

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS AR24 REMOTE CONTROLLED SURGICAL LIGHT TEC-B-0022 REV5 1/14 Page 1 EQUIPMENT LABELS AND SPECIFICATIONS ATTENTION, CONSULT MANUAL FOR FURTHER INSTRUCTIONS. INDICATES SPECIAL USER

More information

INSTALLATION INSTRUCTIONS LED RETROFIT ASSEMBLY (LRA) Rev F

INSTALLATION INSTRUCTIONS LED RETROFIT ASSEMBLY (LRA) Rev F SAFETY S IMPORTANT SAFETY INFORMATION SUITABLE FOR DRY OR DAMP LOCATIONS. NOT FOR USE WITH PHASE CUT DIMMERS. Risk of shock. Disconnect power before installation. DANGER CONVIENT AUX EMPLACEMENTS HUMIDES.

More information

Revision THERMO TECHNOLOGIES. USDT 2001 Differential Controller. Installation and User s Guide

Revision THERMO TECHNOLOGIES. USDT 2001 Differential Controller. Installation and User s Guide Revision 8 THERMO TECHNOLOGIES USDT 2001 Differential Controller Installation and User s Guide USDT 2001 DIFFERENTIAL CONTROLLER Installation and User s Guide Table of Contents Introduction General Information

More information

30A SMART ENERGY MANAGEMENT SYSTEM TM

30A SMART ENERGY MANAGEMENT SYSTEM TM 30 Amp EMS Display Panel P/N 00-00903-030 (Black) 30 Amp EMS Distribution Panel P/N 00-0091-000 CAUTION The 30A SMART EMS is a centralized power switching, fusing, and distribution center. Power from the

More information

INSTRUCTION BOOK FOR. Tensioned Dual Masking Electrol

INSTRUCTION BOOK FOR. Tensioned Dual Masking Electrol INSTRUCTION BOOK FOR Tensioned Dual Masking Electrol Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read

More information

CYCLOPS Z Purge Indicator

CYCLOPS Z Purge Indicator Low cost Simple to install & use Highly reliable & maintenance free Enclosure vent is part of casing Local & remote status indicator Casing available in anodized aluminum & 316 stainless steel 12 or 24

More information

Automatic Changeover Medical Manifold Installation, Operation and Maintenance Manual

Automatic Changeover Medical Manifold Installation, Operation and Maintenance Manual Automatic Changeover Medical Manifold Installation, Operation and Maintenance Manual Andersen Medical Gas 12 Place Lafitte Madisonville, LA 70447 http://www.themedicalgas.com 1-866-288-3783 Model Number:

More information

RF Point Level Control with Sensor Monitor

RF Point Level Control with Sensor Monitor The 681 Point Level Control utilizes DPDT relays to provide switching for peripheral devices (such as pumps) in level applications. A sensor attached to the control acts as an antenna to transmit the process

More information

Specification Grade Contemporary Wall Mount/Technical Installation Data

Specification Grade Contemporary Wall Mount/Technical Installation Data AVAILABLE CONFIGURATIONS RECESSED MOUNT SURFACE MOUNT MOUNTING REQUIREMENTS A. Recessed Mount: Minimum 4-Gang Box, 1-5/8 in. Deep (72.8 Cubic Inches) with 4-Gang Box Cover (20.3 Cubic Inches) B. Surface

More information

Technical Offer. Antek Model 6200 Analyzer Determine Total Sulfur and Total Nitrogen in a single analyzer

Technical Offer. Antek Model 6200 Analyzer Determine Total Sulfur and Total Nitrogen in a single analyzer Technical Offer Antek Model 6200 Analyzer 2015.4 Determine Total Sulfur and Total Nitrogen in a single analyzer Meet sulfur regulations and control your process with continuous sulfur and/or nitrogen measurements

More information

C Power Connection Kit

C Power Connection Kit 1548-4000C Power Connection Kit For use with Dekoron 2700 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4000C electrical connection kit distirbuted by Heat-Line is

More information

IMPORTANT INSTRUCTIONS INSTALLATION AND STARTUP MODEL GDCP-A CONTROL PANEL

IMPORTANT INSTRUCTIONS INSTALLATION AND STARTUP MODEL GDCP-A CONTROL PANEL IMPORTANT INSTRUCTIONS INSTALLATION AND STARTUP MODEL GDCP-A CONTROL PANEL WARNING USE OF HOUSING FOR FIELD WIRING WILL VOID THE FACTORY WARRANTY. Transmitter is considered water resistant only when the

More information

LS1 SERIES IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

LS1 SERIES IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE. The LS1 Series of commercial and industrial LED fixtures is designed to be used in utility strip applications using suspension or surface mount installation. The LS1 Series is designed for use in 120 277V,

More information

SERIES VAC Microprocessor Based Direct Spark Ignition Control FEATURES DESCRIPTION APPLICATIONS THE TOTAL SOLUTION FOR GAS IGNITION CONTROL

SERIES VAC Microprocessor Based Direct Spark Ignition Control FEATURES DESCRIPTION APPLICATIONS THE TOTAL SOLUTION FOR GAS IGNITION CONTROL SERIES 35-72 120 VAC Microprocessor Based Direct Spark Ignition Control 35.72.03 FEATURES Two Mounting Configurations Open Board With Stand-Off's - saves space and cost Potted - protection for washdown

More information

SERVOMEX 335A2014 PURGE ASSY Operator Manual

SERVOMEX 335A2014 PURGE ASSY Operator Manual SERVOMEX 335A2014 PURGE ASSY Operator Manual Part Number: 335A2014-MAN Revision: 1 Language: English Installation Manual Model 2700 Analyzer Purge Assembly i User and Installation Manual Ref: 335A2014/335A2010/335A1023

More information

M Remote Mounting Kit

M Remote Mounting Kit M9208-250 Remote Mounting Kit Installation Instructions M9208-250 Part No. 34-636-2200, Rev. A Issued August 29, 2014 Applications IMPORTANT: Use this M9208-250 Remote Mounting Kit only to control equipment

More information

System 350 S350C Temperature Slave Stage Module

System 350 S350C Temperature Slave Stage Module FANs 930, 930.5, 125, 121 Product/Technical Bulletin Issue Date April 8, 2014 System 350 Temperature Slave Stage Module The Temperature Slave Stage Module is used in conjunction with the A350 Temperature

More information

INSTALLATION GUIDE FOR VM-3000 SERIES INTEGRATED VOICE EVACUATION SYSTEM

INSTALLATION GUIDE FOR VM-3000 SERIES INTEGRATED VOICE EVACUATION SYSTEM For Service Technicians only INSTALLATION GUIDE FOR VM-3000 SERIES INTEGRATED VOICE EVACUATION SYSTEM This manual describes works to be performed with the unit's case open. Leave all these works to a qualified

More information

P66 Series Electronic Fan Speed Controls

P66 Series Electronic Fan Speed Controls FANs 125, 121 Pressure Controls Section P Product/Technical Bulletin P66 Issue Date 0498 P66 Series Electronic Fan Speed Controls The P66 is a pressure actuated electronic motor speed controller. This

More information

Overview. Selection of System Components VT BBK/CWH. Chart LNG Vehicle Tank and Fuel System Installation Guidelines

Overview. Selection of System Components VT BBK/CWH. Chart LNG Vehicle Tank and Fuel System Installation Guidelines Overview The information contained in this bulletin is intended to provide general installation guidelines and recommended specifications. It will aid an up-fitter or OEM in system design and/or installation

More information

FOR USE WITH MODEL NUMBERS:

FOR USE WITH MODEL NUMBERS: INSTALLATION AND MAINTENANCE MANUAL SAFESITE /DUROSITE HZx/ STW SERIES WITH MOUNTING ACCESSORIES Document No: 9100-127-2297-99 Rev C AUGUST 2015 FOR USE WITH MODEL NUMBERS: HZXXXXXW01 HZXXXXXW45 HZXXXXXS45

More information

M9109 Series Electric Non-spring Return Actuators

M9109 Series Electric Non-spring Return Actuators 34-636- 1190, Rev. D Installation Instructions M9109 Issue Date 03/1/16 M9109 Series Electric Non-spring Return Actuators Installation IMPORTANT: Use this M9109 Series actuator only to control equipment

More information

m WARNING! READ m BEFORE INSTALLATION

m WARNING! READ m BEFORE INSTALLATION m WARNING! READ m BEFORE INSTALLATION 1. GENERAL: A failure resulting in injury or damage may be caused by excessive overpressure, excessive vibration or pressure pulsation, excessive instrument temperature,

More information

Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications

Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications WPC-1 Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications Installation Instructions: Read these instructions in their entirety before performing any installation work. FOR USE WITH POOL AND

More information

Mizer Single Pump and Starter Box

Mizer Single Pump and Starter Box Mizer Single Pump and Starter Box Table of Contents Line Diagram... 2 Overview... 3 Booster Pump Specifications... 3 Water... 3 Electrical... 3 Models... 3 Mounting... 4 Electrical... 6 Motor Rotation...

More information

CSR COMPACT FUSED INTERLOCKED ARKTITE RECEPTACLE - 30 & 60 AMP Installation & Maintenance Information IF 1440

CSR COMPACT FUSED INTERLOCKED ARKTITE RECEPTACLE - 30 & 60 AMP Installation & Maintenance Information IF 1440 CSR COMPACT FUSED INTERLOCKED ARKTITE RECEPTACLE - 30 & 60 AMP Installation & Maintenance Information IF 1440 APPLICATION SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE CSR compact fused interlocked ARKTITE

More information

Operations and Service Manual. X30208 Load Bank

Operations and Service Manual. X30208 Load Bank Operations and Service Manual Read all instructions before using the load bank Contents 1. Components... 3 Total Assembly... 3 2) Specifications... 4 a)... 4 3) Receiving... 5 4) Safety... 5 a) Ground

More information

Replacement Parts List

Replacement Parts List Replacement Parts List PARTS & SERVICE DEPARTMENT Nashville, Tennessee 615-889-8900 Fax: 615-882-2918 parts_team@lochinvar.com www.lochinvar.com Copper-Fin 2 Commercial Pool Heaters CP 992-2072 51 16 19

More information

HOMELINK DOOR OPENER KIT

HOMELINK DOOR OPENER KIT HOMELINK DOOR OPENER KIT P/N 2882082 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain

More information

OmniAire Omnitec Design, Manufacturing Air Purification Equipment Since 1988

OmniAire Omnitec Design, Manufacturing Air Purification Equipment Since 1988 OmniAire 18000 Omnitec Design, Manufacturing Air Purification Equipment Since 1988 For your larger projects the OmniAire 18000 is the right tool. The modular design of this system allows for ease of transport

More information

WarmlyYours ET-SR Series Heating Cable Installation Manual for Roof & Gutter Deicing

WarmlyYours ET-SR Series Heating Cable Installation Manual for Roof & Gutter Deicing WarmlyYours ET-SR Series Heating Cable Installation Manual for Roof & Gutter Deicing Free Design Service 24/7 Installation Support (800) 875-5285 www.warmlyyours.com Assembly Tools Needed Utility knife

More information

Weather-Proof Thermal Mass Flow Meter for Pipe - Duct

Weather-Proof Thermal Mass Flow Meter for Pipe - Duct MF200A Series Weather-Proof Thermal Mass Flow Meter for Pipe - Duct Feature & Application n Accuracy ±1.0% reading n Watch-dog software n Wide turn-down ratio 300 : 1 n Repeatability ±0.15% FS n 16 x 2

More information

Cable Cubby 1200 and 1400 Installation Guide

Cable Cubby 1200 and 1400 Installation Guide e NT: R.com for thtion O P IM tron talla w.ex uide, ins ations. o ww Go t te user g specific nd ple com ctions, a u instr 00 and 400 Installation Guide This guide provides instructions for an experienced

More information

Lumination TM LED Luminaires Suspended LED Fixture (Series EP14)

Lumination TM LED Luminaires Suspended LED Fixture (Series EP14) GE Lighting Solutions Installation Guide Lumination TM LED Luminaires Suspended LED Fixture (Series EP14) Features Long life (50,000 hour rated life) 5 year warranty IP30 Dry location rated BEFORE YOU

More information

Special Specification 6058 Battery Back-Up System for Signal Cabinets

Special Specification 6058 Battery Back-Up System for Signal Cabinets Special Specification Battery Back-Up System for Signal Cabinets 1. DESCRIPTION 2. DEFINITIONS Install a Battery Back-Up System (BBU System) for traffic signals that will provide reliable emergency power

More information

HTP PTP/ PTJ Power Connection Kit for Pipes

HTP PTP/ PTJ Power Connection Kit for Pipes HTP 1548-40PTP/1548-40PTJ Power Connection Kit for Pipes For use with Dekoron 2700 and 2300 Families of Heating Cables. 1548-81HTJ/81HTP for use with 2000 Series Heating Cables. Installation Instructions

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PROPANE GAS CONVERSION KIT High Altitude Only / 2001 6000 FT (610 1829m) Small Package Products / 40,000 130,000 Btu/hr NPLPCONV014C00 This kit is used on: Two Models: PGR5 (Two

More information

Tetra minimax. LED Lighting System. BEFORE YOU BEGIN Read these instructions completely and carefully. Installation Guide

Tetra minimax. LED Lighting System. BEFORE YOU BEGIN Read these instructions completely and carefully. Installation Guide Installation Guide Volt Tetra minimax LED Lighting System GEMMRD-W, GEMMGL-W, GEMMBL-W BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSMENT RISK OF ELECTRIC SHOCK Turn

More information

Installation Instructions: ACCENT SYSTEM

Installation Instructions: ACCENT SYSTEM Installation Instructions: ACCENT SYSTEM READ THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS WILL VOID YOUR WARRANTY! INSTALLATION TIPS Read this entire

More information

CAT-1 Series 3. Installation Guide. The Valley Group, Inc. 871 Ethan Allen Hwy. Suite 104 Ridgefield, CT 06877

CAT-1 Series 3. Installation Guide. The Valley Group, Inc. 871 Ethan Allen Hwy. Suite 104 Ridgefield, CT 06877 CAT-1 Series 3 Installation Guide The Valley Group, Inc. 871 Ethan Allen Hwy. Suite 104 Ridgefield, CT 06877 (203) 431-0262 (203) 431-0296 FAX tvg@cat-1.com Installation of Load Cells for CAT-1 Systems

More information

IMPORTANT: SAFETY INSTRUCTIONS

IMPORTANT: SAFETY INSTRUCTIONS MUV-401H GERMICIDAL AIR PURIFIER Installation & Maintenance Instructions UNPACKING THE UNIT Each MUV-401H germicidal air purifier is shipped with the germicidal lamp placed in a lamp box. Carefully remove

More information

Going the Distance - Solving Power Reach Issues With Diverse DAS Solutions

Going the Distance - Solving Power Reach Issues With Diverse DAS Solutions GE Critical Power Going the Distance - Solving Power Reach Issues With Diverse DAS Solutions Paul Smith Technical Marketing Manager GE Critical Power Paul Smith (214) 385-9070 Paul.D.Smith@GE.com Terrell

More information

INSTRUCTION BOOK FOR. Tensioned Large Advantage Deluxe Electrol

INSTRUCTION BOOK FOR. Tensioned Large Advantage Deluxe Electrol INSTRUCTION BOOK FOR Tensioned Large Advantage Deluxe Electrol Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following:

More information

Lifeline Medical Systems

Lifeline Medical Systems Installation, Operation and Service Manual Lifeline Medical Systems Fully-Automatic Manifold For Use With Liquid Cylinders LQ x HP Liquid x High-Pressure Models Part No. 6-847703-00 Rev. C00 Pg. 1 Introduction

More information

Idle Timer Controller - A-ITC520-A Ford E Series Ford F250 - F Ford F250 - F550 (*B-ITC520-A) F650/F750

Idle Timer Controller - A-ITC520-A Ford E Series Ford F250 - F Ford F250 - F550 (*B-ITC520-A) F650/F750 An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC520-A 2009-2018 Ford E Series 2008-2016 Ford F250 - F550 2017-2018 Ford F250 - F550 (*B-ITC520-A) 2016-2018 F650/F750 *Uses the Ford 24-Pin

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PROPANE GAS CONVERSION KIT High Altitude Only / 2001 6000 FT (610 1829m) Small Package Products / 40,000 130,000 Btu/hr NPLPCONV014B00 This kit is used on: Two Stage Models: PGR5

More information

CLIMAGUARD Outdoor Heat Exchangers

CLIMAGUARD Outdoor Heat Exchangers Product Overview : CLIMAGUARD Outdoor Heat Exchangers TX23 Model TX38 Model TX52 Model 132 Product Overview : Lab- and field-tested to seal out extreme weather CLIMAGUARD Outdoor Heat Exchangers PRODUCT

More information

Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications

Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications WPC1-XXXX-T Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications Installation Instructions: Read these instructions in their entirety before performing any installation work. FOR USE WITH

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 6400 Vehicle Dock INSTALLATION INSTRUCTIONS " " " " " " " " " " " " " " " " " " " " " " " " " " " " PN: 962-020-006 Revision B August 1998 " NOTICE The information contained herein is proprietary and is

More information

Idle Timer Controller - ITC515-A Ford Transit Contact InterMotive for additional vehicle applications

Idle Timer Controller - ITC515-A Ford Transit Contact InterMotive for additional vehicle applications An ISO 9001:2008 Registered Company Idle Timer Controller - ITC515-A 2015-2018 Ford Transit Contact InterMotive for additional vehicle applications Overview The ITC515-A system will shut off gas or diesel

More information