Converting a Series Land Rover to front wheel disc brakes using the kit made by Torrel Industries Ltd,
|
|
- Kerry Wilkins
- 6 years ago
- Views:
Transcription
1 Converting a Series Land Rover to front wheel disc brakes using the kit made by Torrel Industries Ltd, Torrel Industries ltd Series Land Rover front brake conversion kit: Difficulty - Low Except for one section, the manual is very good. The project is no more difficult than rebuilding the front brakes and replacing the bearings. A person well experienced with rebuilding Series Land Rover front brakes and hubs can carry out the conversion in a day. Less experienced people will need a weekend for the project. There are no special modifications needed. Everything is bolt on. Special tools needed You will need your normal work on Series Land Rover tool kit, including the hub wrench, a tube of your favourite gasket sealant and fresh brake fluid. Special tools that a Series Land Rover owner might not have are: 10mm socket or wrench for the bleed nipple, 15 mm socket, 11 mm socket, 8 mm hex socket, T60 Torx socket (The torx socket comes as part of the kit). You will need a torque wrench that will read 150 lb ft of torque and a method of applying that much torque on a couple special fasteners (rent someone from the local gym?). The project The disc brake kit came in a sturdy compact wood box that weighs in at over 100 lbs (umph!). From the beginning everything seems well designed and user friendly. Each screw that needs to be removed to open the box is marked with a spot of raspberry paint. Opening the box the parts are well packed and the small parts are bagged. The kit comes with everything you will need for the conversion except for wheel bearings. Series Land Rover wheel bearings seldom go bad so you are expected to reuse the ones on your vehicle after inspecting them to insure that they are indeed in good condition. The kit even comes with all new lock tabs, oil seals and a package of Permatex thread locker. Throughout the project the one thing that stood out to me is that someone went through a lot of effort to to make the conversion as easy to perform as possible, from the marking of the screws on the shipping container, to the well written manual to the way some components were partially assembled to show how they go together, to the way components were grouped in individual wrapping.
2 Contents of the box as unpacked This is the back plate. It goes where the drum brake back plate is mounted and holds the caliper frame in location. The two back plates provided in the kit are sided and are stamped "Left" and "Right" to help you mount them correctly.
3 The two pictures above show the hub and rotor preassembled. Mel chose 11 inch rotors as being that largest that will fit all Series 16 inch wheels. It is my understanding that kits with larger diameter rotors restrict which 16 inch steel rims will fit without a wheel spacer. Note: I use Discovery I steel wheels. I found my wheels to be a very tight press fit onto the hubs. If I were to do another conversion, I would make a trial fitting between the hub and wheel before mounting the hub then file down any excess metal if the wheels do not slide on prior to assembling the kit. One of the hubs was a tighter fit for the wheel than the other, so be sure to check both. Here is a hub side view. The disc brake hub is slightly longer than the drum brake hub to place the rotor in the correct position for the calipers. This hub is a custom casting. The studs are a larger diameter than the standard series wheel studs.
4 This picture shows the centre section of the rotor. The rotors are from "sport models" of Chevy Luminas and Chevy Monte Carlos equipped with 286mm brakes. The centre of the rotor has been cut to a larger diameter and new mounting holes were drilled. Replacements are available through the kit manufacturer and their dealers. The two piston caliper and the brake pads. The pads lock onto the calipers Here is the most confusing part of the assembly The rubber brake hoses are handed and I found the instructions to identify which is which to be a little difficult to understand. 1. Is the tang mention in the instructions. This hose goes on the left side of the vehicle. 2. Is the rounded point mentioned in the instructions (round surface where 2 adjacent hex flats would be). This hose goes on the right side of the vehicle. The calipers are marked R & L, but are fitted to the Land Rover opposite the manufacturer's marking. So the #1 hose is assembled to the caliper marked "R" and goes on the left side of the vehicle. The #2 hose is assembled to the caliper marked "L" and goes on the right side of the vehicle.
5 Here is the left side back plate installed. It fits where the drum brake back plate was and uses the same fixing bolts and lock tabs. The hole in the top tab is lined up with the rear bolts on the top swivel pin. The hole on the lower tab lines up with the swivel housing oil fill plug. Next step is to lock the lock tabs. Here is a little trick. If you pre bend the lock tabs just a little, about 2/3rds of the way down their length, they will not interfere with the bolt head and the ends are off the back plate enough to get a tool under them to bend them into place. They can be a pain to lock if left flat. The holes are offset on the tabs. Be sure to mount the tabs so that the locking tabs do not partially cover the centre back plate hole. Here is the rotor and hub assembly installed with free play adjusted. The process for mounting the hub and adjusting the bearings is the same as with a drum brake hub. Series Land Rovers wheel bearings need to be set a little loose. The workshop manual explains how to set the play with a dial indicator. Here is an alternate method that a lot of people use. Mount the hub and inner hub nut. Tighten down the inner hub nut to eliminate all free play on the bearings. Spin the hub and retighten the inner nut to make sure the bearings are seated properly and that there is no free play Back off the inner hub nut one and a half flats of the nut. This will provide the free play needed for the bearings. Add the lock washer and outer nut per the manual instructions.
6 Here is the caliper mounting bracket mounted to the back plate The caliper is held to this bracket by two long slip pins that go through the two corrugated rubber boots at the back of the frame. The caliper is free to move on the pins. The pistons press one pad against the rotor, pushing the caliper away from the rotor which engages the pad rigidly mounted to the caliper. The slip pins that mount the caliper to the caliper mounting bracket get torqued to 80 pounds of torque. You can see a horizontal silver cylindrical object next to the lower rubber boot on the caliper mounting bracket. That is one of the two special bolts that mounts the bracket to the frame plate. This puppy is what requires the 148 pounds of torque. This is one side finished and ready to mount the wheel. Yes that is the bottom of a power steering box at the top of the picture and no I do not use the stock tab for mounting the brake hose to the frame. I find that the lower otherwise unused frame mounting tab allows for greater downwards articulation without stretching the rubber brake hose.
7 Going one step farther The lower caliper mounting bracket securing bolt may interfere with removing the swivel housing oil fill plug. If it does the instructions suggest shortening the filler plug so that you can get it off and back on. Even if there is no interference with the plug it will be harder to get the plug on and off and to fill the reservoir. Swivel housings are not handed. You can switch the housings between both sides of the Land Rover and not affect steering, suspension or anything. If they are switched, the filler plug ends up facing forward away from the brake caliper. If you need to remove the swivel assembly to work on axles, differential, replace the swivel seal, work on swivel pins or whatever, you might consider switching the housings to the other axle side. Of course you will needs to keep the steering arms in their original sides. Additional information from the manufacturer: Designing the conversion: During design of the disc brake system we concluded that the only economically practicable approach would be to adapt a widely available disc brake system to the Series Land Rover in a way the minimized the need for any other changes to the Land Rover. Due to the relatively large size of the Series Land Rover swivel ball housing, space between the swivel ball housing and the inner wheel rim is quite limited. We determined that the AC Delco dual piston floating caliper system used on many GM cars was the best choice because of its low profile. The AC Delco calipers and caliper brackets and brake pads can be used without modification and the (GM designed) rotors can be modified using general purpose machine tools to fit our Land Rover application. Because the design is based on relatively straight forward modifications to widely available rotors we are able to commit to providing customers replacement rotors as long as replacement rotors for GM cars are available. Which master brake cylinder: Question: The calipers are 2 pot and the 88 master cylinder is designed to push fluid into a single cylinder at each front brake. Does an 88 master brake cylinder pump enough volume for the disc brakes & get good pedal height on the first try or do you recommend switching to 109 master cylinder? Reply: During application, the pads in a disc brake system are displaced much less than the shoes on a drum brake system so a smaller volume of brake fluid must be moved by the master cylinder. This is offset to some extent buy the larger cross sectional area of the disc brake caliper pistons as compared to the drum brake cylinders but a disc brake system in good condition will have less pedal travel and the pedal will "feel" firmer than in a drum brake system. Note that "pressure" is as important a design consideration as "volume" in choosing a master cylinder. I recommend upgrading any Land Rover to a dual braking system for the significant additional safety margin the dual system provides. Power boost is helpful (and commonly used) in disc brake systems which do not have the same "positive feedback" characteristics as drum brake systems. Mel
55-64 Full Size Chevy
55-64 Full Size Chevy Installation Instructions Power Disc Conversion 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand tools. The only tools you may not
More informationA/F/X Body GM Installation Instructions Manual Disc Conversion
A/F/X Body GM Installation Instructions Manual Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body DBMC09 & PVK71 pictured above (Booster, master & valve setups may vary by upgrades selected) Your
More information1969 Camaro. Concourse Style Disc Brake Conversion Kit Instllation Instructions
Concourse Style Disc Brake Conversion Kit Instllation Instructions 1969 Camaro (1970 Chevelle Kit Shown) This document contains our regular disc brake conversion instructions with the addition of GM assembly
More informationA/F/X Body GM Installation Instructions
A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 68-74 X Body 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand
More information55-64 Full Size Chevy Installation Instructions Standard Disc Conversion
55-64 Full Size Chevy Installation Instructions Standard Disc Conversion DBMC09, PV71 & PVB71 Pictured (Booster, master cylinder & valve setups may vary by upgrades selected) Your new disc brake conversion
More informationA/F/X Body GM Installation Instructions Manual Disc Conversion
A/F/X Body GM Installation Instructions Manual Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body DBMC09 & PVK71 pictured above (Booster, master & valve setups may vary by upgrades selected) Your
More information55-64 Full Size GM (Impala, Bel Air, etc.) This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
SUM-BK1624A Full Size GM Installation Instructions Rear Disc Conversion 55-64 Full Size GM (Impala, Bel Air, etc.) This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured
More informationA /F/X Body Instruction Packet Rear Disc Conversion
A /F/X Body Instruction Packet Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes (pictured left). Rotor
More informationMopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion
Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern
More informationFord 8, 9 Small Bearing Installation Instructions Rear Disc Conversion
Ford 8, 9 Small Bearing Installation Instructions Rear Disc Conversion This kit is for Ford 9 rear axles with the small (2.835 ) style bearing and Ford 8 rear ends. This kit is designed to work with axles
More information60 76 A Body Mopar Power Disc Conversion Installation Instructions
62-72 B & E BodyMopar 60 76 A Body Mopar Power Disc Conversion Installation Instructions Special A-Body only parts shown below (In addition to parts above for A-Body cars, part # MDC66DC & MDC46DC) Your
More informationSignature Series A/F/X Body GM Installation Instructions Power Disc Conversion
Signature Series A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body Your new disc brake conversion kit can be bolted up with standard hand tools. The
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC2001, RC2001X Applications: Mopar 8-3/4 & 9-3/4 Rear Axles Thank you for choosing Leed Brakes for your automotive product needs. Before
More informationGM FULL SIZE REAR DISC BRAKE KIT
GM FULL SIZE REAR DISC BRAKE KIT This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left). If your axle flange measures 3 1/8 from center to center, you need
More informationFull Size GM Installation Instructions
Full Size GM Installation Instructions Rear Disc Conversion 55 64 Full Size GM (Impala, Bel Air, etc.) This kit is for axle with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you
More informationA/F/X Body GM Installation Instructions Power Disc Conversion
A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body DBMC09, PVK71 & RPB1001 pictured above (Booster, master & valve setups may vary by upgrades selected)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationMopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion
Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern
More informationEGR Performance Brakes Assembly Instructions DODGE DANA 70 '87 - '93 (Will not fit stock sized dual rear wheels)
EGR Performance Brakes Assembly Instructions DODGE DANA 70 '87 - '93 (Will not fit stock sized dual rear wheels) Got Brakes? Parts List (2) Vented Rotors (2) Multi hole Cable Mount & L Brkt (2) Axle Tube
More informationFull Size GM Installation Instructions Rear Disc Conversion
Full Size GM Installation Instructions Rear Disc Conversion 65 68 Full Size GM (Impala, Bel Air, etc.) This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION REAR KIT SUM-BK1423 1999-2009 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time to read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take
More informationSignature Series A/F/X Body GM Installation Instructions Rear Disc Conversion
Signature Series A/F/X Body GM Installation Instructions Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes
More informationRED LINE LANDCRUISERS LLC. FJ40-70 series BIG BRAKE KIT INSTRUCTIONS
RED LINE LANDCRUISERS LLC. FJ40-70 series BIG BRAKE KIT INSTRUCTIONS Tired of not have the brake performance on your land cruiser? Have you upgraded to 35,37" Tires, a V8? Well, This brake kit is for you.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Disc Brake Spindle Kit SUM-BKA2447 1964-72 A-BODY 1967-69 F-BODY 1968-74 X-BODY Thank you for choosing SUMMIT RACING for your braking needs. Please take the time to read and carefully
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationA /F/X Body Instruction Packet Rear Disc Conversion
A /F/X Body Instruction Packet Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes (pictured left). If your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A120-4 & A120-5 1964-1/2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive
More informationDBK FULL-SIZE CHEVY DISC BRAKE conversion KIT
DBK5964 1959-1964 FULL-SIZE CHEVY DISC BRAKE conversion KIT impala, bel air, biscayne Installation Instructions does not fit 14" rims must ust 15" or larger for this kit to be installed correctly on your
More informationNEW BRAKE INSTALLATION. Let us show you how a
Tech Article From Newsletter 17.2-2nd Quarter of 2011 NEW BRAKE INSTALLATION Let us show you how a Big Brake Install is easier than you think!! So, you have a 572 (or a hot 383) in your shoebox... you
More information82-92 CAMARO, FIREBIRD/78-87 REGAL, MONTE CARLO, GRAND PRIX/ S-10 RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS
82-92 CAMARO, FIREBIRD/78-87 REGAL, MONTE CARLO, GRAND PRIX/ S-10 RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 82-92 CAMARO/78-87 REGAL YOU WILL NEED TO MODIFY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R1 REAR DRUM TO DISC BRAKE CONVERSION KIT A130-3 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FORCE 10 SPORT R1 REAR DISC CONVERSION KIT A126-50 2005-10 Chevrolet Silverado and GMC Sierra Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationA/F/X Body GM Installation Instructions
A/F/X Body GM Installation Instructions Rear Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body This kit is for axle with a 3 1/8 spread center to center on the top two bolt holes (pictured left).
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationINSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125 1968-81 CAMARO & FIREBIRD 10 & 12 BOLT W/"C" CLIPS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KITS W156-6 & W156-7 1965-74 MOPAR B & E BODY Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationA /F/X Body Instruction Packet Rear Disc Conversion
A /F/X Body Instruction Packet Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes (pictured left). If your
More informationSignature Series A/F/X Body GM Installation Instructions Power Disc Conversion
Signature Series A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body Your new disc brake conversion kit can be bolted up with standard hand tools. The
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationINSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT
INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-4 FULL FLOATING AXLE OR A130-5 (1 PIECE AXLE) Thank you
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KITS: A132-1, A133, A133-1 A134, A134-1 1968-73 MUSTANG/FORD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FX4 ELITE REAR DISC CONVERSION KITS WITH INTERNAL PARKING BRAKE A110-14, A111-25, A111-29 for FORD 8" & 9" REAR ENDS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS POWER FRONT DISC CONVERSION KIT A126-7 1963-66 CHEVY C10 PICKUP NON-POWER FRONT DISC CONVERSION KIT A126-8 1963-72 CHEVY C10 PICKUP Thank you for choosing STAINLESS STEEL BRAKES
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A130 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A157 1991-2004 Dodge Dakota 2WD 1991-2002 Dodge Dakota 4WD 1998-2002 Dodge Durango Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for
More informationDBMC09, PVK71 & RPB1001 pictured above (Booster, master & valve setups may vary by upgrades selected)
A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body DBMC09, PVK71 & RPB1001 pictured above (Booster, master & valve setups may vary by upgrades selected)
More information82-04 S-10 and Midsize GM --- Rear Disc Brake Conversion
82-04 S-10 and Midsize GM --- Rear Disc Brake Conversion 82-04 S-10 and Midsize GM --- Rear Disc Brake Conversion EARLY STYLE 82-92 S-series trucks 78-04 G-body and some F-body LATE STYLE 92-03 S-series
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KITS A148-9 & A148-15 1949-54 Chevy Trucks Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please take the time to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-3 1965-72 GM A-BODY 10 & 12 BOLT AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A121-1, A121-2, A121-3, A121-4 1967-69 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION KITS A126-67 2002-11 GM 2500/3500 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128 1990-1995 JEEP WRANGLER (YJ) WITH DANA 35 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases
More informationASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH DIAMETER SOLID ROTOR PINTO / MUSTANG II
ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH 0.75 DIAMETER SOLID ROTOR 97-978 PINTO / MUSTANG II (FIVE LUG CONFIGURATION ONLY)* PART NUMBER GROUP 0-03-B DISC BRAKES SHOULD ONLY BE INSTALLED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KIT A129-2 1959-64 Full Size Chevrolet Car and FRONT DISC BRAKE CONVERSION KITS A129-3 & A129-4 1965-68 Full Size Chevrolet Car Thank you for choosing
More informationPPM-8022 / PPM-8042 JEEP JK STAGE 2 SYNERGY SUSPENSION SYSTEM Version 1
POLY PERFORMANCE MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8022 / PPM-8042 JEEP JK STAGE 2 SYNERGY SUSPENSION SYSTEM Version 1 GENERAL NOTES: These instructions are also available
More information79-93 MUSTANG RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS. FOR ANY QUESTIONS, PLEASE CALL M-F 8:00a.m.-8:00p.m. EST.
79-93 MUSTANG RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 FORD OWNERS ATTENTION! WHEEL OFFSET Due to the design characteristics of the front suspension of a fox
More informationPPM-8023 / PPM-8043 JEEP JK SYNERGY STAGE 3 SUSPENSION SYSTEM Version 1
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8023 / PPM-8043 JEEP JK SYNERGY STAGE 3 SUSPENSION SYSTEM Version 1 GENERAL NOTES: These instructions are also available on our website;
More informationOur goal is to make the install a breeze. Please read the entire guide before beginning.
www.airkewld.com Page 1 of 6 IRS Axle Kit Install IRS Axle Kit Install Our goal is to make the install a breeze. Please read the entire guide before beginning. KITS SHOULD INCLUDE 2 - Control-arm mounting
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KIT A120-20, A120-21 1964 1 /2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationPPM-D44538RJK JK Rear 5.38 Ring and Pinion Installation Instructions Version 1
PPM-D44538RJK JK Rear 5.38 Ring and Pinion Installation Instructions Version 1 GENERAL NOTES: Gear set up and installation should be performed by someone experienced in gear and axle set up Special tools
More informationAPPLIED GMC / 1 (800) KATO RD. FREMONT, CA GMC ALL DISC BRAKE KIT
APPLIED GMC 510-440-1101 / 1 (800) 752-7502 47626 KATO RD. FREMONT, CA 94538 GMC ALL DISC BRAKE KIT Shade Tree Mechanic's Guide to Disc Brake Upgrade Installation Instructions Written by: Edited by: Randy
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 970-973 FORD MUSTANG (DRUM / DISC SPINDLE) PART NUMBER GROUP 0-905 WARNING INSTALLATION OF THIS KIT SHOULD ONLY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KITS SUM-BK1200, SUM-BK1201, SUM-BK1202, SUM-BK1203 1964-72 A-BODY 1967-69 F-BODY 1962-74 X-BODY (NOTE: 62-64 X-BODY REQUIRES 5-LUG STEERING ARMS)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A158 1994-97 Dodge Ram 1500 (2WD & 4WD) and REAR DISC BRAKE CONVERSION KIT A158-1 1998-01 Dodge Ram 1500 (2WD & 4WD) Thank you for choosing STAINLESS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-1 FULL FLOATING AXLE OR A130-2 (1 PIECE AXLE) Thank you for choosing STAINLESS
More informationDODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION
More information2014 GM 1500 TRUCK STOP---READ THIS FIRST! 7" Lift KIT. **Read These Entire Instructions Before Starting Anything**
STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2014 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART #50768 & #50769 ) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationNotice: Refer to Adding Fluid to the Brake System Notice in the Preface section.
Page 1 of 6 2008 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2065646 Front Disc Brake Pads Replacement Removal Procedure Tools Required J 23738-A Hand Vacuum Pump.
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.8 OFFSET) BOLT CHEVY PART NUMBER GROUP 0-7 INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED BY PERSONS EXPERIENCED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A118 pre-1985 Ford F150 (except 1983-1984 w/super H/D axle) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More informationWARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil.
WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. Things needed for assembly. -2 tubes of blue loc-tite. I don
More informationNote: The transmission mount just happened to be upside down in this picture. (c) 2015 Total Cost Involved Engineering, Inc. All Rights Reserved.
1970-1981 Chevy Camaro & Pontiac Firebird Custom IFS Installation Instructions 1-855-693-1259 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATION. IF ANY
More informationRevised BX-1000 BLACK MAX
Revised 8-22-12 BX-1000 BLACK MAX PLEASE READ THROUGH THE ENTIRE MANUAL BEFORE INSTALLING YOUR BRAKE SYSTEM WARNING - DO NOT USE BRAKE FLUID - USE ATF HYDRAULIC FLUID ONLY **IMPORTANT** DO NOT USE ANY
More informationBrake Upgrades for FWD/4WD with 5x100 stud pattern
Brake Upgrades for FWD/4WD with 5x100 stud pattern These started out as my original front brakes, & because I m more of a twisty road person, than straight line speed, I didn t think they d be adequate.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-3 1988-98 CHEVY K1500 4WD 10" DRUMS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS SUM-BK1329-X, SUM-BK1329-99904, SUM-BK1330-X, SUM-BK1330-99904 CHRYSLER 8 3 /4", 9 3 /4" and 2-PIECE REAR AXLES Thank you for choosing SUMMIT RACING
More information63-82 CORVETTE IMPALA KIT INSTRUCTIONS
63-82 CORVETTE 61-69 IMPALA KIT INSTRUCTIONS RACE, STREET, 2 PISTON AND 4 PISTON FRONT KITS ARE ALL COVERED IN THESE INSTRUCTIONAL SHEETS. 1 AEROSPACE COMPONENTS 727.347.9915 Preparing the spindle: You
More informationReplacing the hub oil seal.
Replacing the hub oil seal. The most common reason for hub oil seal failure is a blocked axle breather, so check this first before you start. Remove the brass bell-shaped fitting on the top of the axle,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS A112, A112-1 & A112-93 1979-93 FORD MUSTANG with 7.5" & 8.8" AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-2 1955-70 FULL SIZE CHEVROLET Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125-42 GM 10 & 12 Bolt Rear Axles with Staggered or non-staggered Shocks with C-Clips Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR FORGED SUPERLITE BIG BRAKE FRONT HUB KIT WITH 3.00 DIAMETER VENTED ROTOR 968-969 FORD MUSTANG (DISC BRAKE SPINDLE ONLY) PART NUMBER GROUP 0-950 WARNING INSTALLATION OF THIS KIT
More informationBX-1000 Hydraulic Brake System Azusa 8 inch Diameter Wheel
BX-1000 Hydraulic Brake System Azusa 8 inch Diameter Wheel Installation Manual Made by Free Bird Innovations - 1380 Legion Road - Detroit Lakes - MN 56501 PLEASE READ THROUGH THE ENTIRE MANUAL BEFORE INSTALLING
More informationSlowly lower the floor jack. The spring will then come right out.
Jack up the rear, install a set of jack stands and remove the rear tires. Put a floor jack under the lower transverse link (lower control arm) jack up the lower control arm about one inch. With the jack
More informationMOPAR RACE/STREET FRONT BRAKE KIT INSTRUCTIONS. FOR ANY QUESTIONS, PLEASE CALL M-F 8:00a.m.-8:00p.m. EST.
MOPAR RACE/STREET FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 You will need some items for best results when installing your Aerospace Brake kit. The following is recommended: At least
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationDISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:
Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain
More informationSTEERING AND SUSPENSION SYSTEMS
STEERING AND SUSPENSION SYSTEMS UNIT 12: WHEEL AND TIRE DESIGN LESSON 1: WHEEL DESIGN I. Basic wheel construction A. Wheels are made from stamped steel or cast or forged aluminum or alloys. B. A wheel
More informationFor all Ram x4 Trucks, and all Ram x4 trucks.
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD 5 th GEN STEERING KIT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W120-22, W120-23 1964 1/2-69 MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More information'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
More informationMtd kit: Honda Engine Conversions for classic minis. mtd installation manual For Classic minis
Mtd kit: Honda Engine Conversions for classic minis mtd installation manual For Classic minis 1959 2001 Dear Customer, We welcome you to the Honda Powered Mini World. Thank you and Congratulations for
More information