REMOVAL AND INSTALLATION
|
|
- Denis Lindsey
- 6 years ago
- Views:
Transcription
1 Engine Cooling REMOVAL AND INSTALLATION Radiator, Cooling Fan and Shroud Special Tool(s) Wrench, Fan Clutch Nut (T84T-6312-D) Holding Wrench, Fan Pulley (T84T-6312-C) Disconnect Tool, Transmission Cooler Line Removal 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section If servicing the radiator lower fan shroud or the radiator, drain the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section. 3. Remove the parts in the order indicated in the following illustrations and tables. To remove individual parts, only carry out the listed steps: Part Cooling fan 1, 10, Steps Cooling fan shroud 1, 8, 9, 12-14, 16, 17 Radiator 1-14, Copyright 2002, Ford Motor Company Last updated: 11/20/2002
2 Engine Cooling Item Part Number Description Item Part Number Description 1 8C291 Upper air deflector Lower degas bottle hose Upper degas bottle hose clamp Upper degas bottle hose A/C tube Upper radiator hose clamp Upper radiator hose Transmission cooler lines Lower radiator hose clamp Lower radiator hose Lower degas bottle hose clamp (Continued)
3 Engine Cooling Item Part Number Description Item Part Number Description Radiator fan shroud screws ( T558 Inner air deflector req d) 21 A/C condenser support bracket bolt 13 N Radiator upper fan shroud bolt (2 req d) 14 8K618 Radiator upper fan shroud Radiator Cooling fan 16 N Radiator lower fan shroud 4. To install, reverse the removal procedure. bolt (2 req d) If servicing the radiator lower fan shroud or 17 8K619 Radiator lower fan shroud the radiator, fill and bleed the cooling system. For additional information, refer to Cooling System Draining, Filling and 18 Lower air dam push pin (4 Bleeding in this section. req d) 19 Radiator bracket bolt (4 Item 9: Lower Degas Bottle Hose req d) 1. Remove the lower degas bottle hose from the clip on the radiator lower fan shroud. (Continued)
4 Engine Cooling Item 10: A/C Tube 1. On 4.6L engines, detach the A/C tube from the retainers. Item 11: Transmission Cooler and A/C Tubes 1. Disconnect the transmission cooler tubes. Remove the safety retainers from the transmission cooler tubes. Using the special tool, disconnect the quick coupler. If equipped, loosen and remove the screw clamp from the hose. Item 12: Radiator Fan Shroud Screw Removal Note 1. Not all vehicles will have these radiator fan shroud screws. If vehicle is equipped with these screws, please discard them. Item 15: Cooling Fan 1. CAUTION: Cardboard must be placed against the radiator when removing the cooling fan. Failure to follow these procedures can result in damage to the vehicle. Place a piece of cardboard against the radiator to prevent damage while removing the cooling fan. 2. Using the special tools, remove the fan blade and the clutch assembly. 2. Remove the A/C tube brackets from the engine front cover. Item 17: Radiator Lower Fan Shroud Removal Note 1. Remove the power steering tube from the clip on the radiator lower fan shroud.
5 Engine Cooling Item 19: Radiator Bracket Bolt 3. Remove the right inner air deflector from the A/C condenser. 1. If necessary, remove the radiator brackets. Item 21: A/C Condenser Support Bracket Bolt 1. If necessary, remove the condenser brackets. Item 22: Radiator 1. NOTE: It will be necessary to lift the radiator assembly up off the mounts and set it on the frame in order to separate the A/C condenser from the radiator. NOTE: RH side shown, LH side similar. Remove the radiator up off the mounts and set it on the frame. 4. CAUTION: Do not allow the A/C condenser to hang freely or damage to the A/C lines could occur. NOTE: LH shown, RH similar. Using mechanics wire, support both sides of the A/C condenser. 2. Remove the left inner air deflector from the A/C condenser.
6 Engine Cooling NOTE: It is not necessary to evacuate the A/C 8. Disconnect the hose. system. The A/C condenser can remain in the vehicle. NOTE: It will be necessary to lift the A/C condenser up off the lower support. Move the A/C condenser toward the front of the vehicle. Remove the radiator and transmission cooler as an assembly and place it on a bench. 9. NOTE: RH shown, LH similar. Remove the four bolts and the bracket. 6. Remove the bolts and the transmission cooler. Item 22: Radiator 1. NOTE: RH shown, LH similar. Position the bracket and install the four bolts. 7. Remove the splash shield pin-type retainers.
7 Engine Cooling Connect the hose. 3. Install the splash shield pin-type retainers. 6. NOTE: LH shown, RH similar. Remove the mechanics wire from the A/C condenser and position the condenser onto the lower mounts. 4. Install the transmission cooler and bolts. 7. Install the right inner A/C air deflector shield. 5. Set the radiator assembly on the frame.
8 Engine Cooling Install the left inner A/C air deflector shield. Item 11: Transmission Cooler and A/C Tube 1. Install the A/C tube brackets to the engine front cover. Item 21: A/C Condenser Support Bracket 1. If necessary, install the condenser brackets. 2. Connect the transmission cooler tubes. Item 19: Radiator Bracket If equipped, install and tighten the screw 1. If necessary, install the radiator brackets. clamp from the hose. Item 17: Radiator Lower Fan Shroud Installation Note 1. Install the power steering tube to the clip on the radiator lower fan shroud. Item 15: Cooling Fan 1. CAUTION: Cardboard must be placed against the radiator when installing the cooling fan. Failure to follow these procedures can result in damage to the vehicle. Place a piece of cardboard against the radiator to prevent damage while installing the cooling fan. 2. Using the special tools, install the fan blade and the clutch assembly. Using the special tool, connect the quick coupler. Install the safety retainers from the transmission cooler tubes.
9 Engine Cooling Item 10: A/C Tube 1. On 4.6L engines, attach the A/C tube to the retainers. Item 9: Lower Degas Bottle Hose Installation Note 1. Secure the lower degas bottle hose in the clip on the lower cooling fan shroud.
1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More informationREMOVAL AND INSTALLATION
303-08-1 Engine Emission Control 303-08-1 REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Cooler 6.4L Diesel, Vertical Cooler Item Part Number Description 1 Fuel cooler tube 2 W701317 Power steering
More informationIN-VEHICLE REPAIR. Oil Pan Lower. Removal. 2. Disconnect the LH and RH battery ground cables. For additional information, refer to Section
303-01C-1 IN-VEHICLE REPAIR Oil Pan Lower Special Tool(s) 3-Bar Engine Support 303-F070 Lifting Eyes 303-D030 303-01C-1 2. Disconnect the LH and RH battery ground cables. For additional information, refer
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More information2002 Taurus/Sable Workshop Manual
SECTION 211-02: Power Steering REMOVAL AND INSTALLATION 2002 Taurus/Sable Workshop Manual Power Steering Pump Pulley CII Pump Special Tool(s) Installer, Power Steering Pump Pulley 211-009 (T65P-3A733-C)
More informationM-6642-MB Boss Oil Cooler INSTALLATION INSTRUCTIONS
!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician!
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More information2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
More informationINSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block.
303-01B-1 INSTALLATION Engine 303-01B-1 Special Tool(s) 3-Bar Engine Support Kit 303-F072 Lifting Brackets, Engine 303-050 (T70P-6000) Modular Engine Lift Bracket 303-F047 (014-00073) or equivalent 2.
More informationfile://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...
Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More information1999 Villager Workshop Manual
Page 1 of 5 SECTION 303-03: Engine Cooling 1999 Villager Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/27/1998 Cooling System Draining, Filling And Bleeding Draining WARNING: Do not open
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More information2012 Mustang Workshop Manual. 14. Position the lower radiator hose assembly into the vehicle. Connect the lower radiator hose to the radiator.
14. Position the lower radiator hose assembly into the vehicle. Connect the lower radiator hose to the radiator. 15. Connect the coolant hose to the oil cooler. 16. Rotate the SC drive belt tensioner clockwise
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More information1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
More informationPage 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C
More information1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
More informationAutomatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
More information2008 Saturn Aura V6-3.6L
1 of 14 7/17/2016 7:26 PM 2008 Saturn Aura V6-3.6L Vehicle» Engine, Cooling and Exhaust» Cooling System» Radiator» Service and Repair» Radiator Replacement Radiator Replacement (LY7 - Gas, 6 Cyl, 3.6L,
More informationIN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
More informationPage 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
More informationM-5220-MSVT GT500 with Quad Side Exhaust INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationSECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger Body On... 303-04D-2 303-04D-2 Fuel Charging and Controls
More informationMuncie Power Products
Muncie Power Products CMKF08-6400-P8-AC 2008-2010 Ford F-250-550 6.4L Diesel W-WO/AC, WO/Dual Alt. WO/Vacuum Pump INSTALLATION NOTES 1. Using a 8mm socket or wrench, disconnect the negative battery cables
More information1996 Aerostar/Ranger/Explorer
Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch
More informationINSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block.
303-01B-1 INSTALLATION Engine 303-01B-1 Special Tool(s) 3-Bar Engine Support Kit 303-F072 Lifting Brackets, Engine 303-050 (T70P-6000) Modular Engine Lift Bracket 303-F047 (014-00073) or equivalent 2.
More informationPage 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More informationTiming Belt: Service and Repair
2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator
More information2003 Escape Workshop Manual
Page 1 of 6 SECTION 211-02: Power Steering 2003 Escape Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/06/2005 Steering Gear Printable View (633 KB) Special Tool(s) Tie-Rod End Remover
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More informationEngine Removal and Installation
Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle
More informationSECTION A Engine Cooling
303-03A-i Engine Cooling 303-03A-i SECTION 303-03A Engine Cooling CONTENTS PAGE DESCRIPTION AND OPERATION Engine Cooling... 303-03A-2 Coolant Flow Diagram... 303-03A-3 303-03A-2 Engine Cooling 303-03A-2
More informationTHIS BULLETIN IS BEING PROVIDED IN ADVANCE. DO NOT ORDER PARTS OR PERFORM ANY ACTIONS RELATED TO THIS BULLETIN UNTIL JANUARY 15, 2008.
NUMBER: 24-008-07 GROUP: Heating & A/C DATE: December 18, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
More information1 of 3 3/1/ :50 AM
Fan Clutch Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=76&... 1 of 3 3/1/2016 11:50 AM Coupling unit - Viscous Fan Service Repair No
More information2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
More information2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
More information1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1)
1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) Service and Repair Notes REMOVAL STEPS Preparation: Battery ground cable 1. Radiator upper fan shroud Remove from radiator. 2. Cooling fan assembly
More information10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
More informationTiming Belt. Removal 6A 27 ENGINE MECHANICAL (6VD1 3.2L)
Removal 1.Disconnect battery ground cable. 2.Remove air cleaner assembly. 3.Remove radiator upper fan shroud from radiator. 4.Move drive belt tensioner to loose side using wrench then remove drive belt.
More informationPhone Fax
Directions for Installation of ECS Paxton Supercharger Kit Disconnect battery Remove stock serpentine belt Remove stock belt tensioner, save the 2 bolts for later use on supercharger bracket Remove alternator
More information2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
More informationTiming Belt. Removal ENGINE MECHANICAL (6VD1 3.2L) 6A-27
Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator upper fan shroud from radiator. 4. Move drive belt tensioner to loose side using wrench then remove drive
More informationIN-VEHICLE REPAIR. Main Control Valve Body. Removal. 6. Disconnect the transaxle wiring harness electrical connector and TR sensor connector.
307-01-1 Automatic Transaxle/Transmission 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Material Item Thread Sealant with PTFE TA-24 Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid XT-2-QDX
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
More informationFULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L
2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST
More informationREMOVAL AND INSTALLATION
310-00-1 Fuel System 310-00-1 REMOVAL AND INSTALLATION Fuel Tank and Filler Pipe Special Tool(s) Fuel Tank Drain Hose 310-F013 2. NOTE: Steps 2 through 5 are only necessary if servicing the fuel tank or
More information2000 Ranger Workshop Manual
SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationCOMPONENT LOCATION INDEX
COMPONENT LOCATION INDEX 2011-12 ENGINE Cooling System - TSX V6 Fig. 1: Identifying Cooling System Components RADIATOR CAP TEST 2. Wait until the engine is cool, then carefully remove the radiator cap
More informationENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.
REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.
More informationRigMaster Power Service and Repair Manual Document # S400909
Document # S400909 S4.0 Enclosure Parts Breakdown for 2005 and newer To perform many of the repair procedures in this manual it may be necessary to remove a portion of the enclosure to gain access to components.
More informationSECTION 1D2 M161 ENGINE COOLING
SECTION 1D2 M161 ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More information1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
More informationPage 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover
More informationEngine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
More informationRemove four nuts, then the cooling fan assembly.
The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.
More informationTiming Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
More information2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
More information2002 Jeep Grand Cherokee Laredo
Removal WARNING: DO NOT REMOVE THE CYLINDER BLOCK DRAIN PLUGS OR LOOSEN THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE. SERIOUS BURNS FROM COOLANT CAN OCCUR. REFER TO COOLING SYSTEM DRAINING.
More informationIN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Disconnect the eight ignition coil electrical connectors.
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components 303-01A-1 Special Tool(s) Compressor, Valve Spring 303-581 (T97T-6565-A) Holding Tool, Crankshaft 303-448 (T93P-6303-A) 3. Disconnect the eight ignition
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
More informationEXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT
EXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT External Oil Filter with Coolant Filter Kit PACKING LIST: QTY. 4 4 Description Oil Filter Coolant Filter Small Brass 90 Fitting Large Brass 90 Fitting
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT & BALANCE SHAFT BELT
More informationPage 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More informationSECTION Automatic Transaxle/Transmission 4R70E/4R75E
307-01-i Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)... 307-01-2 307-01-2 Automatic
More informationFan Shroud: Service and Repair Fan cowling To remove 1. Remove the upper engine cover.
Fan Shroud: Service and Repair Fan cowling To remove 1. Remove the upper engine cover. 2. Remove the battery cover and undo the battery cables. 3. Remove the battery cooling pipe by releasing it from the
More informationIN-VEHICLE SERVICE. Engine Components
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown
More informationGENERAL PROCEDURES. Component Bleeding. Master Cylinder Priming In-Vehicle or Bench
206-00-1 Brake System General Information 206-00-1 GENERAL PROCEDURES Component Bleeding Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equivalent
More informationREPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2008-105 FORD 6.4 LITER DIESEL F-SERIES VERSION 3/10 Parts Blackbird Wiring Manual Installation Supplement 6.4 liter Diesel Owner s Manual Includes Warrantee Registration
More informationSECTION 1D1 M162 ENGINE COOLING
SECTION 1D1 M162 ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More informationEngine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
More informationDISASSEMBLY AND ASSEMBLY
205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More informationDISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
More information6.4L EGR Delete With Intake Elbow
6.4L EGR Delete With Intake Elbow J I E C B F D G H A Part# A B C D E F G H I J PACKING LIST: QTY. 2 4 2 4 2 Description Exhaust Block-Off Plate Exhaust Gasket Coolant Line Plugs Brass Barbed Hose Connector
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationIN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding
More informationCERTAIN 2018 MODEL YEAR EXPEDITION AND NAVIGATOR VEHICLES EQUIPPED WITH R-1234YF REFRIGERANT - SPECIAL R-1234YF REFRIGERANT SERVICE INFORMATION
PAGE 1 OF 33 CERTAIN 2018 MODEL YEAR EXPEDITION AND NAVIGATOR VEHICLES EQUIPPED WITH R-1234YF REFRIGERANT - SPECIAL R-1234YF REFRIGERANT SERVICE INFORMATION OVERVIEW This program provides special service
More informationLocations. Select Vehicle New TSBs Technician's Reference Isuzu Truck Rodeo LS 2WD V6-3.2L
1 of 4 5/16/2008 1:06 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2001 Isuzu Truck Rodeo LS 2WD V6-3.2L Conversion Calculator
More informationChrysler 2.0L DOHC timing belt procedure REMOVAL
Chrysler 2.0L DOHC timing belt procedure REMOVAL CAUTION: Camshaft or crankshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL F-SERIES DUAL ALTERNATOR VERSION 10/07 Blackbird Installation Supplement for Ford 6.0. Liter Dual Alternator Parts included in the 6.0
More information11/29/2017 Engine Cooling - Coolant Pump - Removal and Installation 2010 Ford Edge MotoLogic Engine Cooling 2010 Edge, MKX
2010 Edge Report a problem with this article 303-03 Engine Cooling 2010 Edge, MKX REMOVAL AND INSTALLATION Procedure revision date: 10/04/2010 Coolant Pump Special Tool(s) Camshaft Holding Tool 303-1248
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationTiming Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage.
1991 Daihatsu Truck Rocky L4-1589cc 1.6L SOHC Page 1 Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. Repair any water leakage
More informationIN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
More informationREMOVAL AND INSTALLATION
501-10-1 Seating 501-10-1 REMOVAL AND INSTALLATION Seat Exploded View, Front Front Seat Backrest NOTE: LH shown, RH similar. 1 64417 Backrest trim cover 2 14D696 Heated seat element (if equipped) 3 64810
More informationM-5220-MB Mustang GT Side Exhaust Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationIntake Manifold: Service and Repair Removal
1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More informationDESCRIPTION AND OPERATION
303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589
More information