AUTO ISOLATOR I AN AUTOMATIC LOSSLESS BATTERY ISOLATOR FOR DUAL BATTERY SYSTEMS
|
|
- Neal Rose
- 6 years ago
- Views:
Transcription
1 INSTRUCTION MANUAL AUTO ISOLATOR I AN AUTOMATIC LOSSLESS ISOLATOR FOR DUAL SYSTEMS MODEL #: VOLTAGE: 12 VDC OUTPUT: 12 VOLTS, 3 AMPS PARALLELING : 200 AMPS File: IM Rev: revc Revised By: Date: YEAR WARRANTY
2 INTRODUCTION The Model AUTO ISOLATOR I system is a lossless isolator replacement for the conventional diode isolator. Designed to be installed in a vehicle with one or more Main batteries that must be isolated from one or more auxiliary batteries. The system consists of a voltage detector and controller Model CONT-12 and a separate 200-ampere rated solenoid, Model SOL-12HO for switching the batteries. In addition to maintaining battery isolation the AUTO ISOLATOR I may parallel the batteries on engine starting if the auxiliary battery has sufficient charge to assist in the cranking. A block diagram of the system appears in figure 1. PUSH BUTTON ALTERNATOR SENSE AUXILIARY SENSE PARALLELING AUXILIARY POWER IGNITION SWITCH ISOLATOR DRIVER VOLTAGE DETECTOR AUX. VOLTAGE DETECTOR TIMER Figure 1 Block Diagram 2
3 SYSTEM OPERATION The system receives its power from the ignition switch. With the switch OFF all the power is removed from the system and the solenoid is deenergized. As soon as the operator turns the ignition ON, the system is powered and detects the voltage of the main and auxiliary batteries. If the auxiliary battery voltage is 12.4 volts or greater, (indicating sufficient charge) cranking the engine will cause the paralleling solenoid to be energized. A 10-second timer will maintain the paralleling solenoid if the engine doesn t start immediately and must be cranked a second time. When the engine starts the alternator output raises the battery voltage. This increase in voltage is detected and the paralleling solenoid is held energized charging both batteries. If when the engine is started the auxiliary battery voltage is below 12.0 volts the paralleling solenoid is not energized while cranking. As soon as the engine starts, the alternator raises the main battery voltage and the solenoid is energized charging both batteries. Upon engine shutdown the ignition switch is placed in the OFF position. Power is removed from the Auto Isolator and the solenoid is de-energized. 3
4 INSTALLATION Install the CONT-12 Controller is a suitable location protected from the weather and engine heat. The SOL-12HO Solenoid may be mounted in the engine compartment or at a location to minimize the length of the battery cables. Install wiring per figure 2. THIS LINE SUPPLIES THE POWER TO OPERATE THE SYSTEM AUTO ISOLATOR I CONTROLLER CONT12 THIS LINE ENERGIZES THE AT ENGINE START IF THE AUXILIARY HAS SUFFICIENT VOLTAGE TO PROVIDE A BOOST +12VOLT FROM IGNITION SWITCH PARALLELING VOLT FROM SENSE LINE, CONNECT DIRECTLY TO SENSE LINE, CONNECT DIRECTLY TO #2 AWG MIN. AUXILIARY ALL WIRES #16 AWG EXCEPT AS NOTED Figure 2 AUTO ISOLATOR I Model INSTALLATION WIRING 4
5 CALIBRATION The voltage setpoints may be altered in the field to suit particular customer requirements. Adjustments are provided to adjust the main battery voltage at which the paralleling solenoid is energized. An additional adjustment permits adjusting the voltage below which the auxiliary battery will not be paralleled for starting boost. CW INCREASES VOLTAGE AUXILIARY VOLTAGE ADJUST VOLTAGE ADJUST INDICATOR ILLUMINATED WHEN VOLTAGE IS ABOVE SETPOINT 13.0 VOLTS INDICATOR ILLUMINATED WHEN AUXILIARY VOLTAGE IS ABOVE SETPOINT, 12.4 VOLTS C1 + U1 + C2 R6 OUTPUT C6 R9 U3 R3 R1 I2 CR3 CR4 Q1 R7 J1 R8 R15 VCC CR2 R18 C7 CI1 R10 CR1 R2 AUX. U5 R13 R17 R19 GND R21 U2 R4 I1 U4 C3 AUX. BAT. BAT. OK I4 OK R20 R11 C4 + R12 C5 KUSSMAUL ELECTRONICS CO I3 AUX R16 B ILLUMINATES DURING ENGINE CRANKING MEASURE AUX. BAT. VOLTAGE HERE MEASURE BAT. VOLTAGE HERE Figure 3 VOLTAGE ADJUSTMENTS AUTO ISOLATOR 1 5
6 SPECIFICATION AND OUTLINE CONTROLLER, Model CONT12 Volts to parallel, normal operation: Volts to parallel, start boost: Battery load: amps. Output current: 3 amps Weight:.4 lbs volts, field adjustable 12.4 volts, field adjustable, Model SOL-12HO Volts: 12 volts D.C. Coil current:.45 amps /16" DIA ,50 OUTLINE, AUTO ISOLATOR I CONTROLLER, CONT OUTLINE, AUTO ISOLATOR I, SOL-12HO 6
7 INSTALLATION RECORD DATE INSTALLED INSTALLED BY VEHICLE IDENTIFICATION VEHICLE OWNER WARRANTY POLICY All products of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Equipment is to be returned, shipping charges prepaid and will be returned, after repair, shipping charges paid. Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and/or use of the Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. 7
INSTRUCTION MANUAL. A battery protector for vehicles with equipment that Is operated with the engine not running. MODEL# INPUT: 12 Volts D.C.
INSTRUCTION MANUAL FILE: IM_091-141_Rev_B DATE: 10-02-03 LOAD MANAGER P A battery protector for vehicles with equipment that Is operated with the engine not running MODEL# 091-141 INPUT: 12 Volts D.C.
More informationAUTO PUMP STATUS CENTER
INSTRUCTION MANUAL AUTO PUMP STATUS CENTER VOLTAGE & PRESSURE MODEL #: 091-198-12-PP File: IM_091-198-12-PP_revD.indd Rev: D Revised By: MFG/PSS Date: 1-30-2015 3 YEAR WARRANTY scan using your mobile device
More informationAUTO REEL -AS MODEL #: AS AUTOMATIC CORD REEL WITH AUTO SAFE INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO REEL -AS AUTOMATIC CORD REEL WITH AUTO SAFE MODEL #: 091-220-20-120-AS INPUT: 120 Volts, 50/60 Hz, 20 Amps File: IM_091-220-20-120-AS_revA.indd Rev: A Revised By: JM Date: 06-09-2015
More informationSUPER AUTO EJECT DELUXE COVER WITH DIGITAL DISPLAY
INSTRUCTION MANUAL SUPER AUTO EJECT DELUXE COVER WITH DIGITAL DISPLAY MODEL #: 091-55-194X-XXX 194: 40A, 194A: 15A, 194B: 20A, 194C: 80A File: IM_091-55-194X-XXX Rev: A Revised By: PSS/JRN Date: 1-15-2018
More informationINSTRUCTION MANUAL MODEL # YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC.
FILE: 091-84.pmd DATE: 9-21-07 INSTRUCTION MANUAL AUTO THROTTLE 1 MODEL #091-84 AN AUTOMATIC HIGH IDLE CONTROLLER 3 YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC. 170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796
More informationINDUSTRIAL CHARGER AUTOMATIC BATTERY CHARGER SERIES 150 KUSSMAUL ELECTRONICS CO., INC. MODEL # XX YEAR WARRANTY INSTRUCTION MANUAL
INSTRUCTION MANUAL FILE: 091-106-150-XX-120 DATE: 10-2-2009 REV: A INDUSTRIAL CHARGER AUTOMATIC BATTERY CHARGER SERIES 150 MODEL # 091-106-150-XX-120 3 YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC. 170
More informationAUTO PUMP 12V MODEL #: V 12 VOLT DC AIR COMPRESSOR SYSTEM INSTRUCTION MANUAL. INPUT: Volts DC, 11 Amps OUTPUT: 100 PSI Max
INSTRUCTION MANUAL AUTO PUMP 12V 12 VOLT DC AIR COMPRESSOR SYSTEM MODEL #: 091-9-12V INPUT: 10-15 Volts DC, 11 Amps OUTPUT: 100 PSI Max File: IM_091-9-12v_revC1.indd Rev: C1 Revised By: PSS/JRN Date: 08-16-2017
More informationAUTO CHARGE 12 HO MODEL #: MODEL #: MODEL #: AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE 12 HO AUTOMATIC SINGLE OUTPUT BATTERY CHARGER MODEL #: 091-170-6 MODEL #: 091-170-12 MODEL #: 091-170-24 File: IM_091-170-xx_revd.indd Rev: D Revised By: MFG Date: 10-23-2013
More informationAUTO CHARGE LPC SERIES
INSTRUCTION MANUAL FILE: IM_091-206-12_revB REV: B REVISED BY: THN DATE: 09-17-2012 AUTO CHARGE LPC SERIES MODEL #091-206-12 LPC STANDARD DISPLAY INPUT: 115 volt, 50/60 Hz, 13 amps OUTPUT: 80 AMPERES 3
More informationAUTO CHARGE 1200 PUMP PLUS
FILE: 091-193-12.pmd REV: B REVISED BY: MFG DATE: 2-14-2011 INSTRUCTION MANUAL AUTO CHARGE 1200 PUMP PLUS AUTOMATIC BATTERY CHARGER MODEL #091-9-1200 INPUT: 115 volt, 50/60 Hz, 10 amps OUTPUT: 40 AMPERES
More informationAUTO CHARGE 3 STEP AUTOMATIC BATTERY CHARGER
INSTRUCTION MANUAL FILE: IM_091-120-XX-XX-(XXX)(XX)_revA.P65 REV: A REVISED BY: PSS DATE: 07-19-13 AUTO CHARGE 3 STEP AUTOMATIC BATTERY CHARGER R MODEL #091-120-XX-XX-(XXX)(XX) 3 YEAR WARRANTY 170 Cherry
More informationAUTO CHARGE 11HO PIM AUTOMATIC BATTERY CHARGER
BOOK# 091-11HO-PIM-1 INSTRUCTION MANUAL AUTO CHARGE 11HO PIM AUTOMATIC CHARGER MODEL #091-11HO-PIM NOTE : This charger is designed for vehicles with dual batteries and negative ground. INPUT :115 volts,
More informationAUTO CHARGE DUAL MODEL #: AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL. Ph: Fax:
INSTRUCTION MANUAL AUTO CHARGE DUAL AUTOMATIC DUAL OUTPUT BATTERY CHARGER MODEL #: 091-145-12 INPUT: 120 Volt, 50/60 Hz, 3.5 Amps OUTPUT BAT 1: 10 Amps OUTPUT BAT 2: 10 Amps File: IM_091-145-12_revb.indd
More informationBATTERY SAVER LOW RIPPLE HO
INSTRUCTION MANUAL BATTERY SAVER LOW RIPPLE HO LOW RIPPLE POWER SUPPLY / AUTOMATIC LOAD SWITCH FOR 12VDC VEHICLE SYSTEMS MODEL #: 091-195-12 INPUT: 120 Volt, 50/60 Hz, 4.5 Amps RMS OUTPUT: 13.2 Volts DC,
More informationAUTO-PUMP 12V HP-VER FOR VERTICAL MOUNT ONLY MODEL #: V-HP-VER 12VDC HIGH OUTPUT AIR COMPRESSOR SYSTEM INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO-PUMP 12V HP-VER 12VDC HIGH OUTPUT AIR COMPRESSOR SYSTEM FOR VERTICAL MOUNT ONLY MODEL #: 091-9-12V-HP-VER INPUT :10-15 volt, 11 amp OUTPUT :125 PSI MAXIMUM File: 091-9-12V-HP-VER_revA
More informationBATTERY SAVER LR HO with USB LOW RIPPLE POWER SUPPLY / AUTOMATIC LOAD SWITCH FOR 12VDC VEHICLE SYSTEMS
FILE: IM_091-195-12-USB_revB1 REVISED BY: PSS DATE: 06-28-2013 INSTRUCTION MANUAL BATTERY SAVER LR HO with USB LOW RIPPLE POWER SUPPLY / AUTOMATIC LOAD SWITCH FOR 12VDC VEHICLE SYSTEMS MODEL #091-195-12-USB
More informationINSTRUCTION MANUAL REMOTE OUTPUT: 40 AMPERES 3 YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC.
FILE: 091-53-12-REMOTE rev g.pmd REV: G 04-01-10 MFG INSTRUCTION MANUAL AUTO CHARGE 1200 REMOTE AUTOMATIC BATTERY CHARGER MODEL #091-53-12-REMOTE INPUT :115 volt, 50/60 Hz, 10 amps OUTPUT: 40 AMPERES 3
More informationDUAL 12 Volt-10 Amp AUTOMATIC BATTERY CHARGER
FILE: 091-145 DATE: 01-02-02 INSTRUCTION MANUAL DUAL 12 Volt-10 Amp AUTOMATIC BATTERY CHARGER MODEL #091-145 INPUT: 120 Volts, 50/60 Hz AC OUTPUT 1: 12 Volts, DC, Isolated OUTPUT 2: 12 Volts, DC, Isolated
More informationAUTO-PUMP 120 VAC AIR COMPRESSOR SYSTEM INSTRUCTION MANUAL. 170 Cherry Avenue West Sayville, NY
INSTRUCTION MANUAL AUTO-PUMP 120 VAC AIR COMPRESSOR SYSTEM MODEL #: #:091-9B-1 091-9B-1 INPUT :120 volt, 50/60 Hz, 1.8 AMPS OUTPUT: 100 PSI MAXIMUM File: 091-9B-1_revA1_GEN3 Rev: A1 Revised By:PSS/JRN
More informationHIGH PRESSURE AIR COMPRESSOR SYSTEM MODEL #: 091-9HP-220 INPUT:
INSTRUCTION MANUAL AUTO-PUMP HP 240 VAC HIGH PRESSURE AIR COMPRESSOR SYSTEM MODEL #: 091-9HP-220 INPUT: 220-240 Vac, 50 Hz, 1.3 Amps 230 Vac, 60 Hz, 1.2 Amps File: IM_091-9HP-220-RevB2.indd Rev: B2 Revised
More informationAUTO EJECT WP MODEL #: WP-012 MODEL #: WP-120 MODEL #: WP-120 AUTOMATIC SHORELINE DISCONNECT INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO EJECT WP AUTOMATIC SHORELINE DISCONNECT MODEL #: 091-18WP-012 MODEL #: 091-18WP-120 MODEL #: 091-20WP-120 File: IM_091-18wp_reve.indd Rev: E Revised By: SO Date: 09-22-2015 092
More informationSUPER 30 AUTO EJECT 30 AMP MODEL #: AUTOMATIC SHORE LINE DISCONNECT INSTRUCTION MANUAL
INSTRUCTION MANUAL SUPER 30 AUTO EJECT AUTOMATIC SHORE LINE DISCONNECT MODEL #: 091-159-30-120 30 AMP File: IM_091-159-30-120_revH.innd Rev: H Revised By: SO Date: 10-15-2015 2 YEAR WARRANTY scan using
More informationLPC 20 MODEL #: LOW PROFILE CHARGER AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL LPC 20 LOW PROFILE CHARGER AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays MODEL #: 091-207-12 INPUT: 120 Volt, 50/60 Hz, 7 Amps OUTPUT: 20 Amps File:
More informationINSTRUCTION MANUAL AUTO CHARGE MODEL # OUTPUT: 15 AMPERES 3 YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC.
File: 091-56-12 rev b.pmd Rev: B, Date: 4-1-10 INSTRUCTION MANUAL AUTO CHARGE 1000 AUTOMATIC BATTERY CHARGER MODEL #091-56-12 INPUT :115 volt, 50/60 Hz, 3.5 amps OUTPUT: 15 AMPERES 3 YEAR WARRANTY KUSSMAUL
More informationAUTO CHARGE 12 DV AUTOMATIC BATTERY CHARGER
File: 091-165-12-DV_revD.PDF Rev: D, Date: 02-25-16 INSTRUCTION MANUAL AUTO CHARGE 12 DV AUTOMATIC BATTERY CHARGER MODEL #091-165-12-DV INPUT: 115 or 230VAC, 50/60Hz OUTPUT: 13.2VDC (nom.), 12 Amperes
More informationAUTO CHARGE 4000 MODEL #: AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL. Ph: Fax:
INSTRUCTION MANUAL AUTO CHARGE 4000 AUTOMATIC DUAL OUTPUT BATTERY CHARGER MODEL #: 091-89-12 INPUT: 120 Volt, 50/60 Hz, 8 Amps OUTPUT BATTERY CHARGER: 40 Amps OUTPUT BATTERY SAVER: 5 Amps File: IM_091-89-12_reve.indd
More informationAUTO CHARGE D2 MODEL #: AUTOMATIC TRIPLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE D2 AUTOMATIC TRIPLE OUTPUT BATTERY CHARGER Designed Specifically for Vehicles with DDEC ENGINES MODEL #: 091-74-12 INPUT: 120 Volt, 60 Hz, 8 Amps OUTPUT VEHICLE BATTERY 1
More informationAUTO CHARGE 4000 MODEL #: LOW PROFILE CHARGER AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE 4000 LOW PROFILE CHARGER AUTOMATIC DUAL OUTPUT BATTERY CHARGER Unit supplied with this display MODEL #: 091-89-12 INPUT: 120 Volt, 50/60 Hz, 5 Amps OUTPUT: 45 Amps File:
More informationAUTO CHARGE 12HO-PIM AUTOMATIC BATTERY CHARGER
BOOK# 091-12HO-1 INSTRUCTION MANUAL AUTO CHARGE 12HO-PIM AUTOMATIC BATTERY CHARGER MODEL #091-12HO-PIM NOTE : This charger is designed for vehicles with a single battery system INPUT :115 volt, 50/60 Hz,
More informationSUPER 30 AUTO EJECT -AE
INSTRUCTION MANUAL SUPER 30 AUTO EJECT -AE AUTOMATIC AIR-ELECTRIC SHORELINE DISCONNECT MODEL #: 091-169-30-120 30 Amps Max, 120 Volt Max, 175 PSI Max File: IM_091-169-30-120_reva.indd Rev: B Revised By:
More informationLPC 40 MODEL #: LOW PROFILE CHARGER WITH PLC AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL LPC 40 LOW PROFILE CHARGER WITH PLC AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays MODEL #: 091-200-12 INPUT: 120 Volt, 50/60 Hz, 5 Amps OUTPUT: 40
More informationPUMP PLUS 2000 PLC MODEL #: PP AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL PUMP PLUS 2000 PLC AUTOMATIC DUAL OUTPUT BATTERY CHARGER Supplied with Dual Bar Graph Display MODEL #: 091-237-12-PP INPUT: 120 Volt, 60 Hz, 3.5 Amps OUTPUT BATTERY 1 and 2: 15 or 18
More informationINSTRUCTION MANUAL ENGINE IDLER MODEL # VOLTGAE MONITOR MODEL # YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC.
FILE: 091-84.P65 date: 06-02-99 INSTRUCTION MANUAL ENGINE IDLER MODULE PART OF A HIGH IDLE SYSTEM ENGINE IDLER MODEL #091-84-005 VOLTGAE MONITOR MODEL #091-84-004 3 YEAR WARRANTY KUSSMAUL ELECTRONICS CO.,
More informationAUTO CHARGE D PUMP PLUS
INSTRUCTION MANUAL AUTO CHARGE D PUMP PLUS AUTOMATIC DUAL OUTPUT BATTERY CHARGER Designed Specifically for Vehicles with DDEC ENGINES MODEL #: 091-9-DPP INPUT: 120 Volt, 60 Hz, 8 Amps OUTPUT VEHICLE BATTERY:
More informationINSTRUCTION MANUAL MODEL # NOTE : This charger is designed for vehicles with dual batteries and negative ground.
INSTRUCTION MANUAL FILE: 091-9-2000.P65 DATE: 4-23-2000 REV. A AUTO CHARGE 2000 PUMP-PLUS AIR COMPRESSOR / BATTERY CHARGER MODEL #091-9-2000 NOTE : This charger is designed for vehicles with dual batteries
More informationINSTRUCTION MANUAL CAUTION
FILE: IM_091-128-12E-40-115 Rev B., 2-16-2006 INSTRUCTION MANUAL AUTO CHARGE ODY q AUTOMATIC BATTERY CHARGER MODEL #091-128-12E-40-115 for ODYSSEY AGM BATTERIES CAUTION This charger is calibrated to the
More informationPUMP PLUS 1000 PLC MODEL #: PP AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL PUMP PLUS 1000 PLC AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays MODEL #: 091-215-12-PP INPUT: 120 Volt, 60 Hz, 3.5 Amps OUTPUT BATTERY 1 and 2: 15
More informationAUTO CHARGE 11 MODEL #: XX. AUTOMATIC BATTERY CHARGER U.L. Configuration INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE 11 AUTOMATIC BATTERY CHARGER U.L. Configuration MODEL #: 091-11-XX NOTE : This charger is designed for vehicles with dual batteries and negative ground. CAUTION This unit
More informationINSTRUCTION MANUAL ENGINE IDLER MODEL # YEAR WARRANTY KUSSMAUL ELECTRONICS CO., INC.
10-19-96 INSTRUCTION MANUAL ENGINE IDLER MODULE PART OF A HIGH IDLE SYSTEM ENGINE IDLER MODEL #091-84-005 3 YEAR WARRANTY ELECTRONICS CO., INC. 170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796 TEL: in NY 631-567-0314
More informationINSTRUCTION MANUAL AUTO-PUMP 220/240 VAC MODEL #091-9B-220. INPUT :220/240 volt, 50/60 Hz, 1.9/2.2 AMPS OUTPUT: 100 PSI MAXIMUM 1 YEAR WARRANTY
BOOK# 091-9B-220 4-18-2002 INSTRUCTION MANUAL AUTO-PUMP 220/240 VAC AIR COMPRESSOR SYSTEM MODEL #091-9B-220 INPUT :220/240 volt, 50/60 Hz, 1.9/2.2 AMPS OUTPUT: 100 PSI MAXIMUM 1 YEAR WARRANTY KUSSMAUL
More informationPUMP PLUS 1200 MODEL #: AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL UM LUS 1200 AUTOMATIC SINGLE OUTUT BATTERY CHARGER Unit supplied with one of these displays MODEL #: 091-193-12 INUT: 120 Volt, 60 Hz, 10 Amps OUTUT: 40 Amps File: IM_091-193-12_revH.indd
More informationPower Distribution System User s Manual. Model: PDS-100
Power Distribution System User s Manual Model: PDS-0 Section Page Product Overview... 1 I) General Information... 2 II) Important Safety Information... 2 III) Installation... 3 A) Materials Provided...
More informationTHE SUPER 16 AUTO EJECT
INSTALLATION GUIDE AND MANUAL 091-182 SUPER 16 AUTO-EJECT THE SUPER 16 AUTO EJECT AUTOMATIC SHORE LINE DISCONNECT 3 YEAR WARRANTY Assembled and Distributed in Europe by LUDO McGURK TRANSPORT EQUIPMENT
More informationSUPER AUTO EJECT AUTOMATIC SHORELINE DISCONNECT 3 YEARS WARRANTY. Assembled in the UK by LUDO McGURK TRANSPORT EQUIPMENT LTD WILMSLOW - U.K.
INSTALLATION GUIDE AND MANUAL SUPER AUTO EJECT AUTOMATIC SHORELINE DISCONNECT 3 YEARS WARRANTY Assembled in the UK by LUDO McGURK TRANSPORT EQUIPMENT LTD WILMSLOW - U.K. A KUSSMAUL ELECTRONICS CO., INC.PRODUCT
More informationMD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version
MD10 Engine Controller Installation and User Manual for the MD10 Engine Controller. Full Version File: MartinMD10rev1.4.doc May 16, 2002 2 READ MANUAL BEFORE INSTALLING UNIT Receipt of shipment and warranty
More informationAUTO CHARGE 12 AUTOMATIC BATTERY CHARGER
INSTRUCTION MANUAL FILE: 091-165-12 reve Rev: E, page 8 DATE: 7-02-15 AUTO CHARGE 12 AUTOMATIC BATTERY CHARGER MODEL #091-165-12 NOTE : This charger is designed for vehicles with a single battery and negative
More informationDURA-PANEL W OUTPUT: 12 VDC, 20 Watt W OUTPUT: 12 VDC, 50 Watt W OUTPUT: 12 VDC, 100 Watt
INSTRUCTION MANUAL DURA-PANEL RIGID SOLAR PANEL CHARGING SYSTEM 20W, 50W & 100W SOLAR PANELS SERIES 091-246-20W OUTPUT: 12 VDC, 20 Watt 091-246-50W OUTPUT: 12 VDC, 50 Watt Charge Controller 091-246-100W
More informationMAXIGARD A2000 SPEED SWITCH. Introduction
A107-05, Page 1 952-361-3026, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 MAXIGARD A2000 SPEED SWITCH Introduction The Maxigard A2000 Speed Switch is designed to monitor
More informationA5000GEC-24VDC ZERO SPEED SWITCH
A208-05, Page 1 952-361-3026, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 A5000GEC-24VDC ZERO SPEED SWITCH Introduction The MAXIGARD A5000GEC-24VDC is a zero speed switch
More informationES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller.
ES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller. Full Version File: ES52rev2.63.doc October 24, 2006 2 Thank You For Purchasing This DynaGen Product
More informationFAN-STOP INSTRUCTION MANUAL
Form 1289 FAN-STOP INSTRUCTION MANUAL IMPORTANT Read these instructions fully BEFORE INSTALLING. Equipment damage and personal injury may result from improper installation and/or use. 1. Instructions 1.
More informationGenerator Start Control Module
Generator Start Control Module Part# GSCM-mini-i ATKINSON ELECTRONICS, INC. 14 West Vine Street Murray, Utah 84107 Contact cbdsales@atkinsonel.com for the proper hookup diagram. Please include the generator
More informationSELECT DIAGNOSTIC GUIDE. INST028 Doc 3.02
SELECT DIAGNOSTIC GUIDE INST028 Doc 3.02 CONTENTS General Information...2 Select Call-Outs...3 Wire Diagram and Legend...4 Diagnostics...6 Excessive Voltage Drop Diagnostics...6 Static Diagnostics...7
More informationOWNER'S MANUAL POWER BOOSTER. Rechargeable 12 Volt DC power supply. Item # Enclose copy of original sales receipt
120 DAY LIMITED WARRANTY REGISTRATION FORM All NORTHERN TOOL+EQUIPMENT products are warranted to the original purchaser only for 120 days from the date of purchase, to be free of defects in materials and
More informationBattery Control Center - Diesel
Service Manual CAUTION: All servicing of the Battery Control Center should be done only by a qualified Service Technician. Inadvertent shorts inside the Battery Control Center could result in severe damage
More informationTABLE OF CONTENTS. Page 1
TABLE OF CONTENTS Safety Precautions and Warnings... 2 Introduction... 3 EZ-CHARGE Battery Conductance Testers... 3 EZ-CHARGE 100 Features... 3 EZ-CHARGE 200 Features... 4 Text Styles Used in this Manual...
More informationSELECT -24 INSTALLATION GUIDE. INST036 Doc 2.02
SELECT -24 INSTALLATION GUIDE INST036 Doc 2.02 CONTENTS General Information...2 Select-24 Diagram...3 Mounting the Select Controller...4 Dual Pole Nosebox Installation...5 Aux Harness Installation...6
More informationRK Standby Battery Operator s Manual
49-8104RK Standby Battery Operator s Manual Part Number: 71-0118RK Revision: C Released: 8/4/17 www.rkiinstruments.com Product Warranty RKI Instruments, Inc. warrants gas alarm equipment sold by us to
More informationBattery Tester. GxT Incorporated, Cheboygan MI, U.S.A. All Rights Reserved E040-01G. 40 & 42HD Operator s Manual
Battery Tester GxT Incorporated, Cheboygan MI, U.S.A. All Rights Reserved E040-01G 40 & 42HD Operator s Manual SPECIFICATIONS Measurement Range...Ferret 40... Ferret 42HD Battery Volts... 4.0 to 19.99...
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL VTC125d-6-12 Voltage Converter An ISO9001 and AS9100 Registered Company Battery Chargers Inverters Power Supplies Voltage Converters 8128 River Way, Delta B.C. V4G 1K5 Canada
More informationBLWS23MDAxS-160 Offline Series 110VAC, 3A Brushless Controller / Motor
BLWS23MDAxS-160 Offline Series 110VAC, 3A Brushless Controller / Motor User s Guide A N A H E I M A U T O M A T I O N 4985 E. Landon Drive Anaheim, CA 92807 e-mail: info@anaheimautomation.com (714) 992-6990
More informationData Bulletin. Ground-Censor Ground-Fault Protection System Type GC Class 931
Data Bulletin 0931DB0101 July 2001 Cedar Rapids, IA, USA Ground-Censor Ground-Fault Protection System Type GC Class 931 09313063 GT Sensor Shunt Trip of Circuit Interrupter Window Area for Conductors GC
More information8 Channel Intelligent Digital Line Output Converter with Auxiliary Input and Remote Level Control OWNERS MANUAL
8 Channel Intelligent Digital Line Output Converter with Auxiliary and Remote Level Control OWNERS MANUAL 1 Introduction Thank you for purchasing Pacific Audio Corporations (PAC) 8ch intelligent line output
More informationOperations Manual. Zero Speed Switch Sensor Model ZS09P
Zero Speed Switch Sensor Model ZS09P The must be referred to for correct installation. Failure to comply with the shall void all warranties and liabilities. Overview The Phares Electronics Model ZS09P
More informationCM3000 SIGNAL TRANSMITTER. Introduction. The MAXIGARD CM3000 is designed to convert shaft speed into a 4/20 ma or 0-10 VDC analog output signal.
CM228-03, Page 1 952-935-4201, INC. (Fax) 952-935-9628 3947 MEADOWBROOK ROAD, MINNEAPOLIS, MN 55426 800-328-0738 CM3000 SIGNAL TRANSMITTER Introduction The MAXIGARD CM3000 is designed to convert shaft
More informationFUSE PANEL. NTI-N NC(Y)/M3 NEBS Level 3 Certified NTI NCD(Y)/M3 Standard Panel with Diodes
0113-03K September 2, 2010 FUSE PANEL Technical Practice NTI-N250140-NC(Y)/M3 NEBS Level 3 Certified NTI-230140-NCD(Y)/M3 Standard Panel with Diodes FEATURES ƒ Negative (-) VDC input voltage, -24 or 48Vdc
More information# Traction Control Window Switch
1 INSTRUCTIONS # 82085 Traction Control Window Switch Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation,
More informationA1500, A1500NF SPEED SWITCH SINGLE SET POINT - SELF CONTAINED. Introduction
A186-05, Page 1 952-361-3026, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 A1500, A1500NF SPEED SWITCH SINGLE SET POINT - SELF CONTAINED Introduction The MAXIGARD A1500
More informationBLY17MDA-2W Series. 24V, 10A Brushless Controller/Motor. User s Guide. 910 East Orangefair Lane, Anaheim, CA
BLY17MDA-2W Series 24V, 1A Brushless Controller/Motor User s Guide A N A H E I M A U T O M A T I O N 91 East Orangefair Lane, Anaheim, CA 9281 e-mail: info@anaheimautomation.com (714) 992-699 fax: (714)
More informationGenerator Start Control Module
Generator Start Control Module Part# GSCM-mini-o ATKINSON ELECTRONICS, INC. 14 West Vine Street Murray, Utah 84107 Contact cbdsales@atkinsonel.com for the proper hookup diagram. Please include the generator
More informationModel: ACP-12 AUTO COMPRESSOR PUMP SYSTEM 12 VDC INSTALLATION & OPERATION MANUAL. Phone:
INSTALLATION & OPERATION MANUAL Model: ACP-12 AUTO COMPRESSOR PUMP SYSTEM 12 VDC Manual Part # M-ACP12 Revised 10/27/08 KK 1 INTRODUCTION The Auto Compressor Pump system is a compact 12 VDC electric motor
More informationVTC610 Series Voltage Converter. Installation & Operation Manual
VTC610 Series Voltage Converter Installation & Operation Manual IMPORTANT SAFETY INSTRUCTIONS 1) SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for this voltage
More informationPick and Hold Module Pin Assignment and Description
CONNECTION SIGNAL DESCRIPTION CONNECTION SIGNAL DESCRIPTION J1 + PWR This pin should be connected to the positive output of the driver power supply. The maximum voltage applied This should pin should not
More informationVTC1000 Series Voltage Converter. Installation & Operation Manual
VTC1000 Series Voltage Converter Installation & Operation Manual INTRODUCTION All new Current Mode switching design offers increased power and reliability in a compact package. Extra input and output filtering
More informationPLATINUM Sport Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE
PLATINUM Sport 2000 Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System
More informationWiring Installation Instructions for : Pressure. Wiring Installation Instructions for : Temperature. 2 1/16 Spek Pro Professional Racing Gauge
Wiring Installation Instructions for : Pressure DIAGRAM 1 Pressure Sensor 1/8 NPT 3 AMP Wiring Installation Instructions for : Temperature GAUGE 12-Pin Wiring Harness & Plug Firewall Grommet DIAGRAM 2
More informationTwo Channel Remote Shutdown Device
Installation & Operation Standard Features: Two Channel Remote Shutdown Device I. Introduction Latched shutdown for increased safety Powerful transmitter with 300 feet range Waterproof sealed transmitter
More information30 Amp Solar Charge Controller
V1.4-M 25Aug2017 30 Amp Solar Charge Controller Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other
More informationAEROMOTIVE Part # INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 16306 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
More informationIV. PROOF OF PURCHASE: A warranty claim must be accompanied by proof of the date of purchase.
PD9100 / 9200 SERIES POWER CONVERTER OWNERS MANUAL PROGRESSIVE DYNAMICS, INC. POWER CONVERTER LIMITED WARRANTY I. LIMITED WARRANTY: Progressive Dynamics, Inc. warrants its power converter to be free from
More informationDC to DC Step Up Converter Model: VTC305
DC to DC Step Up Converter Model: VTC305 Owner's Manual Please read this manual before operating your converter INTRODUCTION Step up a 12 VDC battery to between 13.5 and 17.0 or 24.0 and 27.5 VDC in 0.5
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL VTC180 DC/DC Converter An ISO9001 and AS9100 Registered Company Battery Chargers Inverters Power Supplies Voltage Converters 8128 River Way, Delta B.C. V4G 1K5 Canada T.
More informationSól Dual Voltage Buck Boost Solar Charge Controller Connection & Operation V1.00
Sól Dual Voltage Buck Boost Solar Charge Controller Connection & Operation V1.00 Connection Instructions Remove Bottom 4 cover to attach wires to terminal blocks then attach cover and flip over for mounting
More informationGSC300. Auto Start Engine Controller. Installation and User Manual for the GSC300 Auto Start Engine Controller. Full Version
GSC300 Auto Start Engine Controller Installation and User Manual for the GSC300 Auto Start Engine Controller Full Version File: GSC300_R2_6doc September 2009 LIMITED WARRANTY POLICY: The Northern Lights
More informationTCM D Single Zone, 24 Volt DC Timer Control Module User s Manual D-M-E Company
TCM-03-024D Single Zone, 24 Volt DC Timer Control Module User s Manual D-M-E Company D-M-E Company TCM-03-024D Page 1 SAFETY D-M-E Company products have been designed to be safe and simple to operate.
More informationWEB CONTROL PRODUCTS
WEB CONTROL PRODUCTS User Manual MB Tension Sensor (i) FORM NO. L-20127-G-0501 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual
More informationVC-30 / VC-40 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL
1. INTRODUCTION VC-30 / VC-40 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL This MCU controlled Step Down 24V to 12V DC-DC Converter has a programmable 12.0 to 15.0V output in
More informationC3000 SIGNAL TRANSMITTER. Introduction
C131-05, Page 1 952-361-3026, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 C3000 SIGNAL TRANSMITTER Introduction The MAXIGARD C3000 series is designed to convert shaft
More informationPLATINUM. Sport Haltech 13B Terminated Engine Harness QUICK START GUIDE
PLATINUM Sport 1000 Haltech 13B Terminated Engine Harness QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com
More informationGenerator Start Control Module
Generator Start Control Module Part# GSCM Rev C. Code Version: 5.13 ATKINSON ELECTRONICS, INC. 14 West Vine Street Murray, Utah 84107 Table of Contents Operations... 3 Specifications... 3 GSCM Wiring Diagram...
More informationSOLAR DASH CHARGING SYSTEM USER GUIDE
SOLAR DASH CHARGING SYSTEM Doc 1.01 INST049 INSTALLATION STEP 1 Place 20 watt solar panel in the dash of the vehicle facing up. Note: For ideal results position the vehicle in a manner in which the solar
More informationSTARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS
TJ STARTING SYSTEMS 8B - 1 STARTING SYSTEMS CONTENTS page DESCRIPTION AND OPERATION STARTER MOTOR... 2 STARTER RELAY... 3 STARTING SYSTEM... 1 DIAGNOSIS AND TESTING STARTER MOTOR... 8 STARTER MOTOR NOISE
More informationTD77-2 and ULB42-TD-2 TRAFFIC DIRECTOR CONTROL BOXES
TD77-2 and ULB42-TD-2 TRAFFIC DIRECTOR CONTROL BOXES Important: This product is used to direct traffic. Improper use may result in vehicular collision, personal injury and/or death. Star Headlight & Lantern
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More informationGSC300 Auto Start Engine Controller
GSC300 Auto Start Engine Controller Revision 2.9 Installation and User Manual for the GSC300 Auto Start Engine Controller File: MAN-0039 R2.9, GSC300 User Manual.doc May 2011 2 of 29 Thank You For Purchasing
More information# & XFI Chrysler Big Block ( A Series)/ Hemi/440RB Series Dual Sync Distributor
1 INSTRUCTIONS #305012 & 305013 XFI Chrysler Big Block (383-400A Series)/ Hemi/440RB Series Dual Sync Distributor Thank you for choosing products; we are proud to be your manufacturer of choice. Please
More informationES52. Auto Start Engine Controller. Full Version. Installation and User Manual for the ES52 Auto Start Engine Controller.
ES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller. Full Version File: MAN-0001 R4.0, ES52 User Manual.doc Date: August 2017 Thank You For Purchasing
More informationGSC300 Auto Start Engine Controller
GSC300 Auto Start Engine Controller Revision 2.12 Installation and User Manual for the GSC300 Auto Start Engine Controller File: MAN-0039 R2.12, GSC300 User Manual.doc June 2014 2 of 28 Thank You For Purchasing
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationInstallation Manual for the SHURflo LCB - G Pump Controller
Installation Manual for the SHURflo 902-200 LCB - G Pump Controller INDUSTRIAL PRODUCTS LIMITED WARRANTY SHURflo Industrial series pumps and products are warranted to be free of defects in material and
More information