Original BMW Accessories. Installation Instructions.

Transcription

1 Original BMW Accessories. Installation Instructions. Park Distance Control (PDC) Retrofit Kit BMW 3 Series Coupé (E 9) BMW 3 Series Convertible (E 93) These installation instructions are not valid for cars with the aerodynamics package or M sport package SA 337) Retrofit kit No.: Park Distance Control retrofit kit, rear Park Distance Control retrofit kit, front Park Distance Control retrofit kit, rear Installation time The installation time for the rear PDC retrofit and the front PDC upgrade/retrofit is approx. 3.5 hours each. If the rear PDC retrofit and the front PDC upgrade are installed at the same time, the installation time is approx. 5.5 hours. The installation time may vary depending on condition of the car and the equipment in it. The installation time given does not include time needed for programming/encoding. The total costs for the programming time should be taken into account when calculating retrofitting costs (reimbursement through warranty is not permissible). Important information These installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies. In any event, the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge. All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations. If you experience installation or function problems, limit troubleshooting to approx. 0.5 hours for mechanical or.0 hour for electrical work. In order to reduce costs and avoid any additional expense, send a query immediately to the Technical Parts Support via the Aftersales Assistance Portal (ASAP). Specify the following information: - Chassis number - Part number of the retrofit kit - A precise description of the problem - Work steps already carried out Do not archive the hard copy of these installation instructions since daily updates are made by ASAP! Pictograms Denotes instructions that draw your attention to special features. Denotes the end of the instruction or other text. BMW AG, Munich /007 (Z/Z)

2 Installation information Ensure that the cables and/or lines are not kinked or damaged as you install them in the car. The costs thereby incurred will not be reimbursed by BMW AG. Additional cables/lines that you install must be secured with cable ties. If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used. After the installation work, the retrofit must be programmed / coded via the Retrofit or Conversion path. All pictures show LHD cars; proceed accordingly on RHD cars. Ordering instructions Check colour versions and technical equipment. The following parts are not supplied in the kits and must be ordered separately (see EPC for part number and details). For rear PDC retrofit - Control unit D - Sensors I For front PDC upgrade/retrofit - Control unit P - Sensors T - Clip trim Y - Centre console switch centre Z List of special equipment The following special equipment must be taken into consideration when installing the retrofit kit: SA 35 SA 507 SA 606 SA 609 SA 663 Towing hitch Park Distance Control (PDC), rear Business navigation system Professional navigation system BMW Professional radio Special tools required , Installation wedges BMW AG, Munich /007 (Z/Z)

3 Table of contents Section Page. Rear PDC retrofit parts list (E9 only) Rear PDC retrofit parts list (E93 only) Front PDC upgrade/retrofit parts list Preparatory work (E9 only) Preparatory work (E93 only) Rear PDC retrofit connection diagram Front PDC upgrade/retrofit connection diagram Rear PDC retrofit installation and cabling diagram (E9 only) Rear PDC retrofit installation and cabling diagram (E93 only) Front PDC upgrade/retrofit installation and cabling diagram (E9 only) Front PDC upgrade/retrofit installation and cabling diagram (E93 only) Installing the sensors at the rear (rear PDC retrofit) Installing the front sensors (front PDC upgrade/retrofit) Installing the signal generator (cars built before 09/07 without SA 606/609/663 only) Installing the control module (E9 only) Installing the control module (E93 only) Installing and connecting the rear PDC wiring harnesses (E9 only) Installing and connecting the rear PDC wiring harnesses (E93 only) Connecting power supply Installing and connecting the front PDC wiring harness (all cars) Installing and connecting the front PDC wiring harnesses (E9 only) Installing and connecting the front PDC wiring harnesses (E93 only) Installing the centre console switch centre (front PDC upgrade/retrofit) Concluding work and coding Front and rear PDC circuit diagram BMW AG, Munich /007 (Z/Z) 3

4 . Rear PDC retrofit parts list (E9 only) A B C D E F G H I J K L M N Z Legend A B C D E F G H I J K L M N Rear PDC wiring harness Supply cable Signal generator cable (for cars built before 09/07 without SA 606/609/663 only) Control unit (not supplied in the retrofit kit) Module holder Speed nut (3x) Self-tapping screw 4.8 x 6 mm (3x) Rear signal generator (for cars built before 09/07 without SA 606/609/663 only) Sensor (4x, not supplied in the retrofit kit) Disconnecting ring (4x) Sensor holder (4x, different coding) Fusible link 5 A Miniature connector (3x) Cable tie 00 x 3.6 mm (0x) BMW AG, Munich /007 (Z/Z) 4

5 . Rear PDC retrofit parts list (E93 only) A B C D E G H I J K L M N Z Legend A B C D E F G H I J K L M N Rear PDC wiring harness Supply cable Signal generator cable (for cars built before 09/07 without SA 606/609/663 only) Control unit (not supplied in the retrofit kit) Module holder Part deleted Screw M5 x mm (x) Rear signal generator (for cars built before 09/07 without SA 606/609/663 only) Sensor (4x, not supplied in the retrofit kit) Disconnecting ring (4x) Sensor holder (4x, different coding) Fusible link 5 A Miniature connector (3x) Cable tie 00 x 3.6 mm (0x) BMW AG, Munich /007 (Z/Z) 5

6 BMW NAVIGATION PROFESSIONAL 3. Front PDC upgrade/retrofit parts list O P Q R S T U V W X Y Z Z Legend O P Q R S T U V W X Y Z Cable tie 00 x 3.6 mm (0x) Control unit (not supplied in the upgrade kit) Front signal generator (for cars built before 09/07 without SA 606/609/663 only) Adapter (for cars built before 09/07 without SA 606/609/663 only) Front PDC wiring harness Sensor (4x, not supplied in the upgrade kit) Disconnecting ring (4x) SW 8-pin socket casing SW -pin socket casing (for cars built before 09/07 without SA 606/609/663 only) Sensor holder (4x, different coding) Trim (for cars without centre console switch centre, not supplied in upgrade kit) Centre console switch centre (not supplied in the retrofit kit) BMW AG, Munich /007 (Z/Z) 6

7 4. Preparatory work (E9 only) Conduct a brief test --- TIS No. Disconnect negative pole of battery The following components must be removed first of all Rear PDC retrofit Rear bumper trim Luggage compartment floor trim Right luggage compartment wheel arch trim Side trim at rear right (for cars built before 09/07 without SA 606/609/663 only) Backrest side section, rear seat, right Door sill strip, rear (interior) right Door sill strip, front (interior) right Side footwell trim on right A pillar Trim at the bottom right of the dashboard Glovebox Release fuse holder --- Front PDC upgrade/retrofit Front bumper trim Trim at the bottom right of the dashboard Pedal trim (for cars built before 09/07 without SA 606/609/663 only) Side footwell trim on right A pillar Heating/air-conditioning control Switch centre, centre console /054 Door sill strip, front (interior) right Door sill strip, rear (interior) right Backrest side section, rear seat, right Luggage compartment floor trim Right luggage compartment wheel arch trim BMW AG, Munich /007 (Z/Z) 7

8 5. Preparatory work (E93 only) Conduct a brief test --- TIS No. Disconnect negative pole of battery The following components must be removed first of all Rear PDC retrofit Rear bumper trim Luggage compartment floor trim Right luggage compartment wheel arch trim Rear seat Rear seat backrest Rear backrest partition --- Side trim bottom part at rear right (for cars built before 09/07 without SA 606/609/663 only) Door sill strip, front (interior) right Side footwell trim on right A pillar Trim at the bottom right of the dashboard Glovebox Release fuse holder --- Front PDC upgrade/retrofit Front bumper trim Trim at the bottom right of the dashboard Pedal trim (for cars built before 09/07 without SA 606/609/663 only) Side footwell trim on right A pillar Heating/air-conditioning control Switch centre, centre console /054 Door sill strip, front (interior) right Rear seat Rear seat backrest Rear backrest partition --- BMW AG, Munich /007 (Z/Z) 8

9 6. Rear PDC retrofit connection diagram A A A A3 B B B3 B4 B B5 A4 A5 C C C C Z Branch/ Item Designation Signal Cable colour / Cross-section Connection site in the car Abbreviation / Slot A Rear PDC wiring harness A Natural 8-pin socket casing On control unit D X803 A SW 3-pin socket casing On sensor I, rear right outside X803 A3 SW 3-pin socket casing On sensor I, rear right inside X80 A4 SW 3-pin socket casing On sensor I, rear left inside X80 A5 SW 3-pin socket casing On sensor I, rear left outside X800 B Supply cable B Double flat spring contact Terminal 5 GN/WS 0.50 mm Cars built before 03/07 only To fuse holder A400, 5-pin BL plug Cars built after 03/07 only To fuse holder A400, 5-pin BL plug B Eyelet M6 Terminal 3 Brown/black 0.50 mm On joint connector, in footwell on passenger side B3 Twisted cable CAN high OR/GN 0.35 mm To standard wiring harness, in footwell on passenger side B4 Twisted cable CAN low GN 0.35 mm To standard wiring harness, in footwell on passenger side B5 SW -pin socket casing On control unit D X300 X003 PIN 8 X00 PIN 7 X00 X500 X500 C Signal generator cable For cars built before 09/07 without SA 606/609/663 only --- C SW -pin socket casing On rear signal generator H X479 C Socket contact LS_HI+ BL/GN 0.35 mm C3 Socket contact LS_HI- SW/GN 0.35 mm With branch B5 on control unit D With branch B5 on control unit D X300 PIN 4 X300 PIN 0 BMW AG, Munich /007 (Z/Z) 9

10 7. Front PDC upgrade/retrofit connection diagram S9-S0 S S S S3 S7 S8 V W S4 S5 S6 Branch/ Item Designation Signal Cable colour / Cross-section Connection site in the car Abbreviation / Slot S Front PDC wiring harness S SW 3-pin socket casing On sensor T, front right outside X809 S SW 3-pin socket casing On sensor T, front right inside X808 S3 SW 3-pin socket casing On sensor T, front left inside X807 S4 SW 3-pin socket casing On sensor T, front left outside X806 S5 Socket contact,.5 mm LS_VO+ BL/GR 0.35 mm S6 Socket contact,.5 mm LS_VO- SW/RT 0.35 mm Only for cars built before 09/07 without SA 606/609/663 With socket casing W on front signal generator Q Only for cars built after 09/07 or with SA 606/609/663 Insulate and tie back Only for cars built before 09/07 without SA 606/609/663 With socket casing W on front signal generator Q Only for cars built after 09/07 or with SA 606/609/663 Insulate and tie back S7 Socket contact LS_VO+ BL/GR Only for cars built before 09/ mm without SA 606/609/663 With branch B5 to the control module P Only for cars built after 09/07 or with SA 606/609/663 Insulate and tie back S8 Socket contact LS_VO- SW/RT Only for cars built before 09/ mm without SA 606/609/663 With branch B5 to the control module P Only for cars built after 09/07 or with SA 606/609/663 Insulate and tie back X478 PIN X478 PIN X300 PIN Z X300 PIN BMW AG, Munich /007 (Z/Z) 0

11 7. Front PDC upgrade/retrofit connection diagram S9-S0 S S S S3 S7 S8 V W S4 S5 S6 Branch/ Item Designation Signal Cable colour / Cross-section S9 Socket contact U_WVR GN/VI 0.35 mm S0 Socket contact M_WVR BR/GE 0.35 mm S Socket contact D_WVR GE/BR 0.35 mm S Socket contact U_WVMR GN/GR 0.35 mm S3 Socket contact M_WVMR BR/BL 0.35 mm S4 Socket contact D_WVMR GE/SW 0.35 mm S5 Socket contact U_WVML GN/BR 0.35 mm S6 Socket contact M_WVML Brown/black 0.35 mm S7 Socket contact D_WVML GE/GN 0.35 mm S8 Socket contact U_WVL GN/SW 0.35 mm S9 Socket contact M_WVL BR/WS 0.35 mm S0 Socket contact D_WVL GE/GR 0.35 mm Connection site in the car With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P With socket casing V to control unit P Z Abbreviation / Slot X836 PIN 8 X836 PIN X836 PIN 7 X836 PIN 7 X836 PIN 0 X836 PIN 6 X836 PIN 6 X836 PIN 3 X836 PIN 5 X836 PIN 5 X836 PIN X836 PIN 4 V SW 8-pin socket casing To control unit P X836 W SW -pin socket casing For cars built before 09/07 without SA 606/609/663 only On front signal generator Q X478 BMW AG, Munich /007 (Z/Z)

12 8. Rear PDC retrofit installation and cabling diagram (E9 only) B H C D I A I * Z Legend A B C D H I Rear PDC wiring harness Supply cable Signal generator cable (for cars built before 09/07 without SA 606/609/663 only) Control unit Rear signal generator (for cars built before 09/07 without SA 606/609/663 only) Sensors LHD cars only Terminal 5 pick-up on fuse holder, plug X003 or X003 Terminal 3 pick-up on joint connector X00 CAN high and CAN low pick-up on standard wiring harness X500 and X500 * RHD cars only Terminal 5 pick-up on fuse holder, plug X003 or X003 Terminal 3 pick-up on joint connector X00 CAN high and CAN low pick-up on standard wiring harness X500 and X500 BMW AG, Munich /007 (Z/Z)

13 9. Rear PDC retrofit installation and cabling diagram (E93 only) B A H C I D A I * Z Legend A B C D H I Rear PDC wiring harness Supply cable Signal generator cable (for cars built before 09/07 without SA 606/609/663 only) Control unit Rear signal generator (for cars built before 09/07 without SA 606/609/663 only) Sensors LHD cars only Terminal 5 pick-up on fuse holder, plug X00 Terminal 3 pick-up on joint connector X00 CAN high and CAN low pick-up on standard wiring harness X500 and X500 * RHD cars only Terminal 5 pick-up on fuse holder, plug X00 Terminal 3 pick-up on joint connector X00 CAN high and CAN low pick-up on standard wiring harness X500 and X500 BMW AG, Munich /007 (Z/Z) 3

14 0. Front PDC upgrade/retrofit installation and cabling diagram (E9 only) S P T Q* Z T Q Z Legend P Q Control unit For LHD cars built before 09/07 without SA 606/609/663 only Signal generator front Q* For RHD cars built before 09/07 without SA 606/609/663 only Signal generator front S T Z Front PDC wiring harness Sensors Switch centre, centre console BMW AG, Munich /007 (Z/Z) 4

15 . Front PDC upgrade/retrofit installation and cabling diagram (E93 only) S T P Q* Z T Q Z Legend P Q Control unit For LHD cars built before 09/07 without SA 606/609/663 only Signal generator front Q* For RHD cars built before 09/07 without SA 606/609/663 only Signal generator front S T Z Front PDC wiring harness Sensors Switch centre, centre console BMW AG, Munich /007 (Z/Z) 5

16 . Installing the sensors at the rear (rear PDC retrofit) 8 mm 3 Clean and degrease the bumper trim () at the gluing points (). Drill through the bumper trim () in the centre of the marked holes (3) using a 3 mm twist drill bit. Enlarge the holes in the bumper trim () using a 8 mm step drill. Deburr the edges of the holes. 3 8 mm Z Fit sensors I into disconnecting rings J. I J Z I Fit sensors I into sensor holders K. K Z I I I Sensor holders K are coded. Check the descriptions on sensor holders K. The connection plugs for sensors I point towards the inside of the bumper trim (). K K K Affix sensor holders K to the bumper trim () as per the descriptions: - HI to the inside - HA to the outside K Z BMW AG, Munich /007 (Z/Z) 6

17 3. Installing the front sensors (front PDC upgrade/retrofit) 8 mm 3 Clean and degrease the bumper trim () at the gluing points (). Drill through the bumper trim () in the centre of the marked holes (3) using a 3 mm twist drill bit. Enlarge the holes in the bumper trim () using a 8 mm step drill. 3 Deburr the edges of the holes. 8 mm Z Fit sensors T into disconnecting rings U. T U Z T Fit sensors T into sensor holders X. X Z T T T Sensor holders X are coded. Check the descriptions on sensor holders X. The connection plugs for sensors T point towards the inside of the bumper trim (). X X X Affix sensor holders X to the bumper trim () as per the descriptions: - VLI to the left inside - VRI to the right inside - VA to the outside X Z BMW AG, Munich /007 (Z/Z) 7

18 4. Installing the signal generator (for cars built before 09/07 without SA 606/609/663 only) Rear PDC retrofit E9 only H C C Fit rear signal generator H into the side trim (). Connect branch C to rear signal generator H. Install the side trim () as described in TIS RA Route signal generator cable C along the standard wiring harness to the right-hand side of the boot Z H C E93 only Fit rear signal generator H into the side trim (). Connect branch C to rear signal generator H. Install the side trim () as described in TIS RA 5 43,05. Route signal generator cable C to right partition. C Z Front PDC upgrade/retrofit R Q Q/R All cars Clip front signal generator Q into adapter R. Clip the adapter R into the pedal trim (). The interlocks on front signal generator Q, adapter R and pedal trim () are coded. They will only fit into one position Z BMW AG, Munich /007 (Z/Z) 8

19 5. To install the control module (E9 only) F Rear PDC retrofit Place speed nuts F into the right-hand boot side section () Z Insert control unit D into module holder E. D E Z P Front PDC upgrade/retrofit Insert the control module P into the module holder E. E Z G Insert module holder E into the right-hand boot side section and secure it with self-tapping screws G. E Z BMW AG, Munich /007 (Z/Z) 9

20 6. To install the control module (E93 only) E Rear PDC retrofit The module holder guide () E must be inserted into the brace (). Insert module holder E into brace () and secure with screws G. G Z Insert control unit D into module holder E. E D Z Front PDC upgrade/retrofit Insert the control module P into the module holder E. E P Z BMW AG, Munich /007 (Z/Z) 0

21 7. To install and connect the rear PDC wiring harnesses (E9 only) Cars without SA 35 only Remove the sealing stopper () from the right rear closing panel () Z 30 mm 6 mm Cars with SA 35 only Mark the specified dimensions on the rear closing panel (). Drill through the rear closing panel () at the drilling point () and enlarge the hole using a 40 mm step drill bit. Deburr the hole and coat the bare surfaces with preservative Z All cars A A Route branch A to the boot and insert the grommet (). Route rear PDC wiring harness A into the holding lugs on the holder (). Connect branches A A5 to sensors I (not shown). Fit the bumper trim. A5 A4 A3 A Z For cars built before 09/07 without SA 606/ 609/663 only C A C B5 Route signal generator cable C to control unit D. Connect branches C and C3 to branch B5 as follows: - Branch C, BL/GN cable, to PIN 4 - Branch C3, SW/GN cable, to PIN 0 D C Z All cars Connect branch A and branch B5 to the control module D. BMW AG, Munich /007 (Z/Z)

22 8. To install and connect the rear PDC wiring harnesses (E93 only) Cars without SA 35 only Remove the sealing stopper () from the right rear closing panel () Z Cars with SA 35 only Remove the battery to prevent any damage when drilling. Drill through the rear closing panel () at the circular gradation () using a 40 mm step drill bit. Deburr the hole (3) and prime the bare surfaces Z All cars A A Route branch A to the boot and insert the grommet (). Route rear PDC wiring harness A into the holding lugs on the holder (). Connect branches A A5 to sensors I (not shown). Fit the bumper trim. A5 A4 A3 A Z A Route branch A in the cable duct () along the standard wiring harness to the installation site of the control module D (not shown) Z BMW AG, Munich /007 (Z/Z)

23 8. To install and connect the rear PDC wiring harnesses (E93 only) A For cars built before 09/07 without SA 606/ 609/663 only C C C3 B5 Route signal generator cable C to control unit D. Connect branches C and C3 to branch B5 as follows: - Branch C, BL/GN cable, to PIN 4 - Branch C3, SW/GN cable, to PIN 0 D Z All cars Connect branch A and branch B5 to the control module D. BMW AG, Munich /007 (Z/Z) 3

24 9. To connect power supply B-B4 E9 only Route branches B B4 along the standard wiring harness to the fuse holder () Z B-B4 E93 only Route branches B B4 along the standard wiring harness to the fuse holder () Z Cars built before 03/07 only Connect branch B, GN/WS cable, to PIN 8 of plug X003 (BL 5-pin). X00 M X003 B Z If PIN 8 is already occupied, disconnect socket contact from branch B and with miniature connector M connect to existing cable. Cars built after 03/07 only Connect branch B, GN/WS cable, to PIN 7 of plug X00 (BL 5-pin). If PIN 7 is already occupied, disconnect socket contact from branch B and with miniature connector M connect to existing cable. All cars Route branch B, brown/black cable, to the footwell on the passenger side. X00 Secure branch B to joint connector X00 (cable colours BR/SW). B Z BMW AG, Munich /007 (Z/Z) 4

25 9. To connect power supply B3 M Connect branch B3, orange/green cable, and branch B4, green cable, to the cables of the same colours on the twisted cables () on the standard wiring harness using miniature connectors M. B Z L Cars built before 03/07 only Fit the fuse holder (). Insert fusible link L into slot F Z Cars built after 03/07 only Fit the fuse holder (). Insert fusible link L into slot F 8. L 5 A Z BMW AG, Munich /007 (Z/Z) 5

26 0. To install and connect the front PDC wiring harness (all cars) S Connect front PDC wiring harness A to the holder () with cable ties and route it to behind the right headlight. Connect branches S S4 to sensors T (not shown). Fit the bumper trim. S S S3 S Z Route front PDC wiring harness S along the standard wiring harness through grommets () and () into the interior. S Z Only cars built after 09/07 or with SA 606/ 609/663 Insulate and tie back branch S5, blue/grey cable, and branch S6, black/red cable. For cars built before 09/07 without SA 606/ 609/663 only S5-S Z Route branch S5, blue/grey cable, and branch S6, black/red cable, along the standard wiring harness to the pedal trim (). S6 Connect branches S5 and S6 to socket casing W as follows: - Branch S5, blue/grey cable, to PIN - Branch S6, black/red cable, to PIN S5 Q Connect socket casing W to front signal generator Q. Fit the pedal trim (). W Z BMW AG, Munich /007 (Z/Z) 6

27 . To install and connect the front PDC wiring harnesses (E9 only) S7-S0 P Route branches S7 S0 along the standard wiring harness to control unit P Z V S9-S Z Connect branches S9 S0 to socket casing V as follows: - Branch S9, green/violet cable, to PIN 8 - Branch S0, brown/yellow cable, to PIN - Branch S, yellow/brown cable, to PIN 7 - Branch S, green/grey cable, to PIN 7 - Branch S3, brown/blue cable, to PIN 0 - Branch S4, yellow/black cable, to PIN 6 - Branch S5, green/brown cable, to PIN 6 - Branch S6, blue/black cable, to PIN 3 - Branch S7, yellow/green cable, to PIN 5 - Branch S8, green/black cable, to PIN 5 - Branch S9, blue/white cable, to PIN - Branch S0, yellow/grey cable, to PIN 4 In cars with an existing SA 507, branch B5 corresponds to plug X300 already fitted in the car. P S7 V S8 B Z Only cars built after 09/07 or with SA 606/609/663 Insulate and tie back branches S7 and S8. For cars built before 09/07 without SA 606/609/663 only Connect branches S7 and S8 to branch B5 as follows: - Branch S7, blue/grey cable, to PIN 5 - Branch S8, black/red cable, to PIN All cars Connect branch B5 and socket casing V on control unit P. BMW AG, Munich /007 (Z/Z) 7

28 . To install and connect the front PDC wiring harnesses (E93 only) S7-S0 P Route branches S7 S0 along the standard wiring harness to control unit P Z V S9-S Z Connect branches S9 S0 to socket casing V as follows: - Branch S9, green/violet cable, to PIN 8 - Branch S0, brown/yellow cable, to PIN - Branch S, yellow/brown cable, to PIN 7 - Branch S, green/grey cable, to PIN 7 - Branch S3, brown/blue cable, to PIN 0 - Branch S4, yellow/black cable, to PIN 6 - Branch S5, green/brown cable, to PIN 6 - Branch S6, blue/black cable, to PIN 3 - Branch S7, yellow/green cable, to PIN 5 - Branch S8, green/black cable, to PIN 5 - Branch S9, blue/white cable, to PIN - Branch S0, yellow/grey cable, to PIN 4 V S7 In cars with an existing SA 507, branch B5 corresponds to plug X300 already fitted in the car. Only cars built after 09/07 or with SA 606/ 609/663 P S8 B Z Insulate and tie back branches S7 and S8. For cars built before 09/07 without SA 606/ 609/663 only Connect branches S7 and S8 to branch B5 as follows: - Branch S7, blue/grey cable, to PIN 5 - Branch S8, black/red cable, to PIN All cars Connect branch B5 and socket casing V on control unit P. BMW AG, Munich /007 (Z/Z) 8

29 3. To install the centre console switch centre (front PDC upgrade/retrofit) Z Clip the centre console switch centre Z into the trim Y. Y BMW NAVIGATION PROFESSIONAL Z BMW NAVIGATION PROFESSIONAL Y Clip trim Y into the trim for the centre instrument panel. Connect the plug () from centre console switch centre Z to the heating/air-conditioning control (). Clip in the heating/air-conditioning control (). Z Z BMW AG, Munich /007 (Z/Z) 9

30 4. Concluding work and coding These retrofit systems require encoding. - Connect the battery Cars with an existing rear PDC only - Encode/program the front PDC retrofit via path Conversion All cars - Encode/program the retrofit via path Retrofit - Conduct a brief test - Conduct a function test - Re-fit the car components as required BMW AG, Munich /007 (Z/Z) 30

31 5. Front and rear PDC circuit diagram 0,35 GE/BR 0,35 BR/GE 0,35 GN/VI 0,35 BR/BL 0,35 GE/GR 0,35 GN 0,35 OR/GN 0,35 SW/RT 0,35 BL/GR 0,50 GN/WS X00/ B* X003/ B* A400 A ,35 BL/GN 0,35 SW/GN 0,50 BR/SW 5A X00/ B* B30/T* B3/T* B3/T* B33/T* F8 X500/ B3* X500/ B4* X300/ B5* A8/D*/ P* GN/SW 0,35 BR/WS 0,35 GN/BR 0,35 BR/SW 0,35 GE/GN 0,35 GN/GR 0,35 0,35 GE/SW GE/GR 0,35 GN/BR 0,35 GE/GN 0,35 GN/GR 0,35 BR/BL 0,35 GN/VI 0,35 BR/GE 0,35 GE/BR 0,35 0,35 GN/SW 0,35 BR/WS 0,35 BR/SW 0,35 GE/SW 5A F8 8 X806/ S4* X807/ S3* X808/ S* X809/ S* 7 8 X836/ V* Kl. 5 KL. 3 CAN_H CAN_L U_WVL M_WVL D_WVL U_WVML M_WVML D_WVML U_WVMR M_WVMR D_WVMR U_WVR M_WVR D_WVR LS_VO+ LS_VO- LS_HI+ LS_HI- U_WHL M_WHL D_WHL U_WHML M_WHML D_WHML U_WHMR M_WHMR D_WHMR U_WHR M_WHR D_WHR X300/ B5* X803/ A* 5 4 X478/ W* H40/Q* H45/H* X479/ C* X800/ A5* 3 X80/ A4* 3 X80/ A3* 3 X803/ A* 3 B34/I* B35/I* B36/I* B37/I* Z BMW AG, Munich /007 (Z/Z) 3

32 5. Front and rear PDC circuit diagram Legend A8 A400 Control unit, D* rear PDC and P* front PDC Fuse holder B30- B33 B34- B37 Front sensors, T* Rear sensors, I* H40 H45 Front signal generator, Q* (for cars built before 09/07 without SA 606/609/663 only) Rear signal generator, H* (for cars built before 09/07 without SA 606/609/663 only) X300 -pin SW socket casing, B5* X00 Terminal 3 pick-up joint connector contact, B* X00 5-pin BL socket casing, B* (cars built after 03/07 only) X003 5-pin BL socket casing, B* (cars built before 03/07 only) X478 -pin SW socket casing, W* (cars built before 09/07 without SA 606/609/663 only) X479 -pin SW socket casing, C* (cars built before 09/07 without SA 606/609/663 only) X500 Open cable, CAN high pick-up, B3* X500 Open cable, CAN low pick-up, B4* X803 8-pin natural socket casing, A* X806 3-pin SW socket casing, S4* X807 3-pin SW socket casing, S3* X808 3-pin SW socket casing, S* X809 3-pin SW socket casing, S* X800 SW 3-pin socket casing, A5* X80 3-pin SW socket casing, A4* X80 Black 3-pin socket casing, A3* X803 3-pin SW socket casing, A* X836 8-pin SW socket casing, V* All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram. Cable colours BL Blue OR Orange BR Brown RT Red GE Yellow SW Black GN Green VI Violet GR Grey WS White BMW AG, Munich /007 (Z/Z) 3