EDG6000 Electronic Digital Governor

Size: px
Start display at page:

Download "EDG6000 Electronic Digital Governor"

Transcription

1 INTRODUCTION GAC s digital governor is designed to regulate engine speed on diesel and gaseous fueled engines. When paired with a GAC actuator the EDG is a suitable upgrade for any mechanical governor system that needs flexibility, precision, or accurate control of governed speed. The EDG is designed for industrial engine applications from generator sets, and mechanical drives, to pumps or compressors. Electronic Digital Governor 3 INSTALLATION Vertical orientation allows for the draining of fluids in moist environments. Mount in a cabinet, engine enclosure, or sealed metal box. Computer SPECIFICATIONS PERFORMANCE Isochronous Operation ± 0.% Speed Range / Governor Idle Adjust Droop Range KHz Full Range - % regulation Speed Trim Programmable 0-0%, (default = %) Ambient Temperature Supply Polarity Power Consumption Speed Sensor Signal Actuator Load Share / Synchronizer Input Reverse Power Protection Transient Voltage Protection Overspeed Vibration Shock Testing ENVIRONMENTAL INPUT / OUTPUT -4 VDC Battery Systems (. to 33 VDC) Negative Ground (Case Isolated) 70mA max. Continuous Plus Actuator Current 0-0 VRMS MAX Amps Continuous 0- VDC ( V nominal, reversed, 7Hz / V Max) RELIABILITY -40 to 8 C (-40 to 80 F) Relative Humidity up to % All Surface Finishes Internet Connection COMPLIANCE / STANDARDS Agency Communications Dimension Weight Mounting PHYSICAL Smart VU Software A computer and an internet connection will be required to download and then run GAC s SmartVU software. CE and RoHS Requirements RS-3-C, SAE J3 See Section 3 Installation oz (70g) Any position, Vertical Preferred Fungus Proof and Corrosion Resistant Yes 0V Rated to A DC 7G, 0-0 Hz 0G Peak 0% Functional Testing 4 4 [.8 ] 00 [ ] 000 WIRING Avoid Extreme Heat 77 [ ] 8 [ 40 ] [ 8 ].37 4 pin AMPSEAL requires GAC mating connector EC0 or cable harness CH0 [mm] Dimensions: in * Keep reading for diagrams and/or additional notes PIN DEFINITION GAUGE S Actuator (+) # AWG Actuator (-) # AWG Polarity not required for actuator 3 Magnetic Pickup (+) #0 AWG * Ground to Terminal 4 Aux Input #0 AWG * 0 - V Range, V Nominal, Reverse Polarity Speed Select A #0 AWG * Ground to Enable Speed Select B #0 AWG * Ground to Enable 7 RS-3 Enable #0 AWG * Connect to ground to enable RS3 8 Overspeed Output # AWG * A Max Variable Speed Input #0 AWG Ground / Battery Pwr (-) / Magnetic Pickup (-) # AWG Battery Power (+) # AWG CAN Termination #0 AWG 3 (CAN H / RS3 TX) #0 AWG 4 (CAN L / RS3 RX) #0 AWG RECOMMENDATIONS * K Ω Resistive or 0- VDC selectable in software Battery Twisted Pair to Magnetic Speed Pickup A amp fuse must be installed in the positive battery lead to protect against any overload or short circuit * 0 Ohm Resistor Built-In, Jumper to CAN L #4 * Twist Wires 4 turns per foot. Shielded cable should be used for all external connections to the EDG control. One end of each shield, including the speed sensor shield, should be grounded to a single point on the EDG case. Electronic Digital Governor. PIB 44 E

2 EDG Mating Connector Basic Wiring 4 Magnetic Speed Pick-Up Fuse AMP Max - + Actuator - Battery + /4 VDC PIN Variable Speed Variable speed is enabled when Terminals and are not grounded. See WIRING COM- BINATIONS. A K potentiometer or a 0- VDC signal can be connected to terminal. Variable Speed can be used as a fixed speed setting if both SPEED MIN and SPEED MAX parameters are set to the same RPM and no potentiometer is connected. See section for Variable Speed Setup Procedure. 0 - VDC Signal K Potentiometer PIN 3 Magnetic Speed Pickup PIN 3 & 4 CAN or RS3 Wires must be twisted and/or shielded for their entire length (4 turns per foot) Gap between speed sensor and gear teeth should not be smaller than 0.0 in. (.mm) Speed sensor voltage should be at least VAC RMS during crank If the detects no input from the magnetic pickup, WARNING the EDG will set the actuator to 0V and set the speed to 0 RPM. After the EDG has detected loss of magnetic pickup, the LED # will flash red and the system must be reset. To reset the EDG, DC power must be cycled. If CAN termination is required, tie pin to pin See CAN WIRING below. CAN WIRING CAN 0 Ohm Open RS3 WIRING Tx Rx PIN 4 Accessory Input Case 4 3 The Aux Terminal accepts signals from: GAC Accessories connect directly to this terminal Auto Synchronizers Load Sharing Units Aux Other Governing Accessories Case 4 CAN H CAN L = optional CAN termination 8 7 DB Connector RS3 Enable to ground in order to commuicate (Pin 7). On CANbus there is only engine speed output. It can not take speed requests. The ECU ID is on the CANbus with message EEC Serial cable must be of straight-through type (common), and NOT of null modem/crossover type (uncommon). PIN & Open Terminals PIN 8 Speed Select Grounded Terminals Overspeed Output WIRING COMBINATIONS PIN PIN Speed Mode Open Open Variable Speed (or Fixed Speed) Ground Open Fixed Speed Open Ground Fixed Speed Ground Ground Fixed Speed 3 - Idle Setup of these speed modes will be reffered to in section. If the detects the engine speed has reached the WARNING value specified by OVERSPEED parameter (Main Menu), the will command the engine speed to 0 RPM and the actuator output to 0V. After the EDG has detected an overspeed, LED # will flash and the system must be reset. To reset the EDG, DC power must be cycled. LED DEFINITIONS LED # COLOR DEFINITION FLASHING GREEN Controller is powered and the microprocessor is initialized. FLASHING RED Controller has tripped overspeed. SOLID GREEN Controller has achieved the chosen running speed. FLASHING RED ALTERNATING RED & GREEN SOLID GREEN SOLID RED SOLID AMBER Will pulse when the controller has not reached running speed. Variable speed enabled and controller has achieved the chosen running speed. SPEED Select is enabled and controller has achieved the chosen running speed. SPEED Select is enabled and controller has achieved the chosen running speed. SPEED Select & is enabled and controller has achieved the chosen running speed. LED LED Electronic Digital Governor. PIB 44 E

3 SMARTVU The is programmed using GAC s SmartVU software. The SmartVU installation file and instructions can be found at: Setup Connection Menu If your PC only has a USB and no serial port, you need an adapter. You also need to find which COM port will communicate with the EDG. A tutorial on how to find your COM port can be found here: After the has been properly selected from the Setup Connection Submenu and SmartVU recognizes the device, parameters can then be adjusted using the Main Menu and the Governor Advanced Settings Menu. Pin 7 on the EDG must be grounded for communication to SmartVU. 7 PRE-START The following parameters must be set before starting the engine: Setup & Safety Overspeed Teeth Ramp Up Ramp Down Starting Parameters Crank Cutoff Actuator Ramp Rate Actuator Begin Point For more details on these parameters, refer to Section Main Menu Parameters 8 STARTING THE ENGINE Crank the engine with DC power applied to the governor system. The initial amount of power to the actuator is determined by the ACTUATOR BEGIN POINT parameter (default is 0% open). ACTUATOR RAMP RATE will control the rate at which fuel is increased to start the engine. ADJUSTING FOR STABILITY Once the engine is running at operating speed and at no load, the following governor performance adjustment can be made to increase engine stability. Setup Connection menu is found under the Configure pull-down menu. PARAMETER MAIN MENU ADJUSTMENT PROCEDURE Increase this parameter until instability develops. Main Menu P (GAIN) I (STABILITY) D (DEADTIME) Then, gradually decrease this parameter until stability returns. Finally, decrease this parameter one increment further to ensure stable performance. If instability persists, adjust the stability parameter. Follow the same adjustment procedure as the P parameter. If instability persists, adjust the deadtime parameter. Follow the same adjustment procedure as the P parameter. P, I, & D parameter adjustments may require minor changes after engine load is applied. Normally, adjustments made at no load achieve satisfactory performance. If further performance improvements are required, refer to Section () GOVERNOR ADVANCED SETTINGS and Section () SYSTEM TROUBLESHOOTING. For more details on these parameters, refer to Section GOVER- NOR ADVANCED SETTINGS. Click Save Data to Device to update governor s memory. 3 Electronic Digital Governor. PIB 44 E

4 MAIN MENU PARAMETERS Remember to save. Click Save Data to Device to update governor s memory. FIXED SPEED PARAMETERS Speed,,3 0-00,800,00 EDG selects one of three fixed speeds. Fixed Speed 3 is Idle Speed (RPM) Idle speed must be set below operation speed but above crank termination (00-00) even if it is not being used. VARIABLE SPEED PARAMETERS Speed Min 0-00 Minimum allowed RPM desired Speed Max 0-00 Maximum allowed RPM desired STARTING PARAMETERS Crank Cutoff Actuator Ramp Rate 0-0 Actuator Begin Point RPM at which EDG switches from starting to governing Throttle position s rate of change from the throttle begin point to 0%, during the start/crank cycle (% / s) Starting position of the actuator during the start/crank cycle (%) Perform the following precedure with the unit powered and the CAUTION engine not running to set the variable speed limits. The potentiometers must be calibrated to those limits afterwards. Variable Speed Setup Procedure In the [3 - Idle Speed] parameter under FIXED SPEED PARAMETERS, input a value 0 RPM below the desired idle speed setting. Navigate to the Governor Advanced Settings menu by clicking on the Options drop-down menu and selecting Governor Advanced Settings. SETUP & SAFETY Overspeed Cust. Dep. 0 Teeth Ramp Up Ramp Down RPM at which to automatically shut off the actuator Number of teeth on flywheel [freq(hz) = (RPM/0) x (# of gear teeth)] Allows for rapid engine speed response with minimal overshoot during engine start and acceleration (RPM/s) Allows for rapid engine speed response with minimal undershoot during engine deceleration (RPM/s) Select/enable the check box labeled Variable Speed Voltage. 4 Electronic Digital Governor. PIB 44 E

5 Return to the main page. Under VARIABLE SPEED PARAMETERS, input the desired idle RPM in the box labeled Speed min and hit the Enter key. GOVERNOR ADVANCED SETTINGS Governor Advanced Settings will further adjust engine stability and can be accessed through the Options pull-down menu on SmartVU s Main Menu.. Input the desired maximum RPM in the box labeled Speed Max and hit the Enter key. You can set the Speed min and max parameters to the same value with no input on pin and use as a fixed speed switch input. Variable Speed Pot Calibration After setting Speed min and max, set the speed input to its minimum; either 0 volts or turn the potentiometer full counter clockwise. Click the button labeled Speed Pot Calibration and hit enter ( or click the button labeled Save Data to Device ). 8. Set the speed input to its maximum; either volts or turn the potentiometer full clockwise.. Click the button leveled Speed Pot Calibration and hit enter ( or click the button labeled Save Data to Device ) The displayed values under Pot min and Pot max are in counts. When a k potentiometer is used as a variable speed input, the total speed range will be 0 to V, which is equivalent to 0 to counts displayed. When a 0 to V input is used, the full range of 0 to 3 counts will be displayed and the unit will operate at its best resolution. ENGINE RESPONSE PARAMETERS P I 0-0, 0 = Max Gain 0-0, 0 = Longest Time 0 Proportional (P) set point of the PID control 3 Integral (I) set point of the PID control D 0-0 Derivative (D) set point of the PID control Dither 0-0%. 0 = No Dither Fuel Limit 0-0% 0 Adds a high-frequency, low amplitude signal to the actuator to prevent the butterfly valve from sticking in harsh environment Maximum allowable throttle % the system can command UPDATE RATE & PID SCALE Update Rate Changes the rate at which the PID routine is called.(ms) P Scale If a PID Scale multiplier is changed I Scale (e.g. P Scale), the corresponding parameter (e.g. P) will be affected in D Scale 0-0 two ways. See below. PID Multipliers If the multiplier is decreased by, the corresponding parameter will double. If the multiplier is increased by, the corresponding parameter will halve. If Multiple PID (See SPECIAL FUNCTIONS below) is enabled, you can not change the PID scale. Simply disable and re-enable. SPECIAL FUNCTIONS Multiple PID Off, On OFF Enables or disables the multi-pid tables which displays a variable map over full engine speed and actuator duty cycle range. When multiple PID is enabled, the user has the ability to set the gain, stability, and Deadtime at each RPM and commanded actuator duty cycle in a -position (8 speeds by 7 positions with customizable axis values) table using the System Tuning menu. The System Tuning menu can be accessed through the Options drop-down Electronic Digital Governor. PIB 44 E

6 SPECIAL FUNCTIONS (CONTINUED) Overspeed Normally Open Off, On On Overspeed normally open (Box Checked), output voltage (Pin 8) is a 0 until the overspeed threshold is exceeded, at which point output (Pin 8) goes to battery Voltage. Off: Overspeed normally open (box Unchecked) output voltage (pin 8) is at battery voltage until the overspeed threshold is exceeded, at which point output goes to 0 V. Variable Speed Voltage Off, On Off Selects type of input for variable speed signal. Checked = 0- VDC, Unchecked = K Ohm Potentiometer Take caution when adjusting the up/down arrows on the Engine CAUTION Response Parameters on the Main Menu when multiple PID is enabled since any changes made will be reflected for the specific cell (speed vs. position) on the table and not the entire table itself. When a kω potentiometer is hooked up, you will have a range of 0 - V which is 0 - ADC. With 0 - V input enabled, you can use the full range of 0-3 ADC. AUX Aux Input Enable Off, On Off Enables or disables load sync input. SYSTEM TROUBLE SHOOTING SYSTEM INOPERATIVE If the engine governing system does not function, the fault may be determined by performing the voltage tests described in Steps through Positive (+) and negative (-) refer to meter polarity. Should normal values be indicated during troubleshooting steps, then the fault may be with the actuator or the wiring to the actuator. Tests are performed with battery power on and the engine off, except where noted. See actuator publication for testing procedure on the actuator. STEP 3 WIRES Power (-) & (+) Pick-Up 3 & Ground Actuator & Battery (-) & (+) NORMAL READING Battery Supply Voltage ( or 4V DC) 0 VAC RMS min while cranking 0-0 VDC while cranking PROBABLE CAUSE OF ABNORMAL READING DC battery power not connected. Check for blown fuse Low battery voltage Wiring error Gap between speed sensor and gear teeth too great Check Gap Improper or defective wiring to the speed sensor Resistance between 3 and Ground should be 30 to 00 ohms. See specific mag pickup data for resistance. Defective speed sensor. SPEED parameter set too low Short/open in actuator wiring Defective speed control Defective actuator, see Actuator Troubleshooting INSTABILITY Slow Periodic Non-Periodic INSTABILITY SYMPTOM An irregularity of speed below 3Hz. (Sometimes severe) Erratic Engine Behavior PROBABLE CAUSE OF ABNORMAL READING Decrease the update rate of the controller by decreasing the UPDATE Advanced parameter. (Each time UPDATE is changed, P, I, and D must be re-adjusted. Check fuel system linkage during engine operation for: a. binding b. high friction c. poor linkage Add a small amount of droop. Increasing the P parameter should reduce the instability but not totally correct it. If this is the case, there is most likely a problem with the engine itself. Check for: a. engine mis-firings b. an erratic fuel system c. load changes on the generator set voltage regulator. If unsuccessful in solving instability, contact GAC for assistance. GAC@governors-america.com or call: Silver Street, Agawam, MA 00 USA GAC@governors-america.com Electronic Digital Governor. PIB 44 E

7 UNSATISFACTORY PERFORMANCE SYMPTOM Engine Overspeeds Overspeed shuts down engine after running speed is reached Overspeed shuts down engine before running speed is reached Actuator does not energize fully Engine remains below desired governed speed NORMAL READING Do Not Crank. Apply DC power to the governor system. Manually hold the engine at the desired running speed. Measure the DC voltage between Terminals (-) & (+) on the speed control unit. PROBABLE CAUSE OF ABNORMAL READING After the actuator goes to full fuel, disconnect the speed sensor at Terminal If the actuator is still at full fuel-speed then the control unit is defective. If the actuator is at minimum fuel position and there exists an erroneous position signal, then check speed sensor If the voltage reading is 0 to 0 VDC: a. SPEED parameter set above desired speed b. Defective speed control unit If voltage reading is > 0 VDC then check for: a. actuator binding b. linkage binding If the voltage reading is below 0 VDC: a. Defective speed control unit Check #TEETH parameter. Incorrect number of teeth entered. Examine the SPEED and OVERSPEED operating parameters for the engine Check resistance between Terminals 3 & Ground. Should be 30 to 00 ohms. See specific Magnetic Pick-up data for resistance. SPEED parameter set too high. OVERSPEED set too close to SPEED. Actuator or linkage binding. Speed Control unit defective. OVERSPEED set too low If the speed sensor signal is erroneous, then check the wiring. Measure the voltage at the battery while cranking. If the voltage is less than: a. 7V for a V system, or b. 4V for a 4V system, Then: Check or replace battery. Momentarily connect Terminals and The actuator should move to the full fuel position. Measure the actuator output, Terminals &, while running under governor control. Actuator or battery wiring in error Actuator or linkage binding Defective actuator Fuse opens. Check for short in actuator or harness. If voltage measurement is within VDC of the battery supply voltage level, then fuel control is restricted from reaching full fuel position, possibly due to mechanical governor, carburetor spring, or linkage interference. SPEED parameter set too low 70 Silver Street, Agawam, MA 00 USA GAC@governors-america.com 7 Electronic Digital Governor. PIB 44 E

IGA225 Integrated Governor & Actuator

IGA225 Integrated Governor & Actuator INTRODUCTION GAC s integrated digital governor and actuator is designed to regulate engine speed on diesel and gaseous fueled engines. The IGA is a suitable upgrade for any mechanical governor system that

More information

EDG5500 Electronic Digital Governor With Quikset Display

EDG5500 Electronic Digital Governor With Quikset Display 1 INTRODUCTION EDG5500 Electronic Digital Governor With Quikset Display GAC s EDG5500 digital governor is designed to regulate engine speed on diesel and gaseous-fueled engines. The EDG system is a suitable

More information

ESD5500E Series Speed Control Unit

ESD5500E Series Speed Control Unit ESD5500E Series Speed Control Unit 1 SPECIFICATIONS INTRODUCTION PERFORMANCE Isochronous Operation ± 0.25% or better Speed Range / Governor 1-7.5 KHz Continuous Speed Drift with Temperature ±1% Maximum

More information

ESD5100 Series Speed Control Unit PART NUMBER ESD5120 ESD (127)

ESD5100 Series Speed Control Unit PART NUMBER ESD5120 ESD (127) ESD5100 Series Speed Control Unit 1 INTRODUCTI The ESD5100 Series speed control unit is an all electronic device designed to control engine speed with fast and precise response to transient load changes.

More information

EEG6500 Enhanced Electronic Governor

EEG6500 Enhanced Electronic Governor 1 2 INTRODUCTION GAC s EEG6500 digital governor is designed to regulate engine speed on diesel and gaseous-fueled engines. The EEG system is a suitable replacement for any mechanical governor system that

More information

ENGINE GOVERNING SYSTEMS

ENGINE GOVERNING SYSTEMS ENGINE GOVERNING SYSTEMS ESD5400 Series Speed Control Unit INSTALLATION The speed control unit is rugged enough to be placed in a control cabinet or engine mounted enclosure with other dedicated control

More information

ESD5550 / 5570 Series Speed Control Units

ESD5550 / 5570 Series Speed Control Units ESD5550 / 5570 Series Speed Control Units 1 The speed control unit is rugged enough to be placed in a control cabinet or engine mounted enclosure with other dedicated control equipment. If water, mist,

More information

EEG6550 Enhanced Electronic Governor

EEG6550 Enhanced Electronic Governor 1 2 INTRODUCTION Computer SPECIFICATIONS PERFORMANCE Isochronous Operation ± 0.25% Speed Range / Governor Idle Adjust Droop Range Speed Trim Supply Polarity Power Consumption Speed Sensor Signal Actuator

More information

ESD-5550/5570 Speed Control Unit. Manual

ESD-5550/5570 Speed Control Unit. Manual Manual Doc.-No. : ESD-5550- Version : 1.0 Date of Issue : HUEGLI TECH Switzerland This document, and the information contained herein is the intellectual property of HUEGLI TECH. It is to be used only

More information

ESD-5550/5570 Series - Speed Control Unit

ESD-5550/5570 Series - Speed Control Unit ESD-5550/5570 Series - Speed Control Unit Table 1. Starting Fuel Control ESD-5550/5570 Series Speed Control Units Speed Ramping Single Element Speed Switch (Overspeed) 2 Element Speed Switch (Overspeed

More information

ENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE. GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA , USA MEMBER

ENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE. GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA , USA MEMBER ENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE MEMBER GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA 01001-2907, USA LSM672 LOAD SHARING MODULE PRODUCT TECHNICAL INFORMATION PTI 4000 AUGUST

More information

ESD-5500E Series - Speed Control Unit

ESD-5500E Series - Speed Control Unit ESD-5500E Series - Speed Control Unit INTRODUCTION The ESD-5500E Series speed control unit is an all electronic device designed to control engine speed with last and precise response to transient load

More information

with discrete output (Overspeed) with auxiliary input (Synchronizer and Load Sharing)

with discrete output (Overspeed) with auxiliary input (Synchronizer and Load Sharing) Document: Digital Speed Governor Versions SDG-25 SDG-35 with discrete output (Overspeed) with auxiliary input (Synchronizer and Load Sharing) Integrated Heatsink Programming and Diagnostic Port Mode and

More information

ESC2301. Universal Electronic Governor Controller Operation Manual

ESC2301. Universal Electronic Governor Controller Operation Manual ESC2301 Universal Electronic Governor Controller Operation Manual *Replaces most Woodward, Barber Colman & Cummins Speed Controls Features Smoke Limit Control, Idle Speed Control, 12V or 24V input Suitable

More information

10V. the rack of the oil pump must be on the

10V. the rack of the oil pump must be on the P.E.D 20.. ESG2002 series ELECTRONIC GOVERNOR INSTRUCTION A1000C-W ELECTROMAGNETIC ACTUATOR Before inst al l el ectromag neti c, p lea se inspect that the rack of the oil pump shouldn' t be stuck in any

More information

PRODUCT SERIES: DPG-2100

PRODUCT SERIES: DPG-2100 Service Information PRODUCT SERIES: DPG-2100 DYNA Programmable Governor for Isochronous Generators Calibration and Troubleshooting for DPG-2101, DPG-2102, DPG-2103, DPG-2104 DPG-2100 The DPG-2100 governors

More information

EG3000. Generator Electronic Governor Controller Operation Manual

EG3000. Generator Electronic Governor Controller Operation Manual EG3000 Generator Electronic Governor Controller Operation Manual Smoke Limit Control, Idle Speed Control, suitable for Builtin, Non-Built-in and PT Pump Type Actuator. SP POWERWORLD LTD Willows, Waterside,

More information

EG3002. Electronic Engine Governor Controller User Manual

EG3002. Electronic Engine Governor Controller User Manual EG3002 Electronic Engine Governor Controller User Manual Engine Start Smoke Limiting function & IDLE Speed Setting For External, Built-in, PT-Pump type and hydraulic drive actuators Newly added extreme

More information

EG1065X. Compatible with Barber Colman* Dyn1-1065X series * Use for reference purpose only and not a genuine Barber Colman product.

EG1065X. Compatible with Barber Colman* Dyn1-1065X series * Use for reference purpose only and not a genuine Barber Colman product. EG1065X Generator Electronic Governor Controller Operation Manual Compatible with Barber Colman* Dyn1-1065X series * Use for reference purpose only and not a genuine Barber Colman product. Headquarters

More information

EG1069X. Generator Electronic Governor Controller Operation Manual

EG1069X. Generator Electronic Governor Controller Operation Manual EG1069X Generator Electronic Governor Controller Operation Manual Smoke Limit Controller Compatible with Barber Colman Dyn1-1069X series *Use for reference purpose only and not a genuine Barber Colman

More information

KT145 Series John Deere 6076 with Nippondenso Inj. Pump

KT145 Series John Deere 6076 with Nippondenso Inj. Pump KT145 Series John Deere 6076 with Nippondenso Inj. Pump 30 Years Strong! Introduction The KT145 Series Governor System Installation Kit provides the necessary brackets and hardware to install a GAC precise

More information

KT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump

KT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump KT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump 30 Years Strong! Introduction The KT101 Series Governor System Installation Kit provides the necessary brackets and

More information

KT230 Series Caterpillar 3406 Governor System Installation Kit

KT230 Series Caterpillar 3406 Governor System Installation Kit KT230 Series Caterpillar 3406 Governor System Installation Kit 30 Years Strong! Introduction The KT230 Series Governor System Installation Kit provides the necessary brackets and hardware to install a

More information

MD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version

MD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version MD10 Engine Controller Installation and User Manual for the MD10 Engine Controller. Full Version File: MartinMD10rev1.4.doc May 16, 2002 2 READ MANUAL BEFORE INSTALLING UNIT Receipt of shipment and warranty

More information

1.0 Features and Description

1.0 Features and Description 1.0 Features and Description The is an intelligent actuator designed for precise control of quarter turn valves and dampers. Using stepper motor technology, the SmartStep proportionally positions valves

More information

Kelly HSR Series Motor Controller with Regen User s Manual V 3.3. Kelly HSR Opto-Isolated Series Motor Controller with Regen.

Kelly HSR Series Motor Controller with Regen User s Manual V 3.3. Kelly HSR Opto-Isolated Series Motor Controller with Regen. Kelly HSR Opto-Isolated Series Motor Controller with Regen User s Manual HSR72601 HSR72801 HSR12401 HSR12601 HSR12901 HSR14301 HSR14501 HSR14701 Rev.3.3 Dec. 2011 Contents Chapter 1 Introduction... 2 1.1

More information

MAGPOWR Spyder-Plus-S1 Tension Control

MAGPOWR Spyder-Plus-S1 Tension Control MAGPOWR TENSION CONTROL MAGPOWR Spyder-Plus-S1 Tension Control Instruction Manual Figure 1 EN MI 850A351 1 A COPYRIGHT All of the information herein is the exclusive proprietary property of Maxcess International,

More information

MAGNAMAX DVR DIGITAL VOLTAGE REGULATOR

MAGNAMAX DVR DIGITAL VOLTAGE REGULATOR MAGNAMAX DVR DIGITAL VOLTAGE REGULATOR TECHNICAL MANUAL MODEL DVR 2000 AND DVR 2000C FIGURE 1 - FRONT AND REAR VIEW OF VOLTAGE REGULATOR...4 SECTION 1- INTRODUCTION...5 GENERAL DESCRIPTION...5 SPECIFICATIONS...5

More information

DYNA Power Control Manual For Plus 1, Plus 2, Plus 4 and Plus 6 Ft. Lb. Systems

DYNA Power Control Manual For Plus 1, Plus 2, Plus 4 and Plus 6 Ft. Lb. Systems DYNA Power Control Manual For Plus 1, Plus 2, Plus 4 and Plus 6 Ft. Lb. Systems General Information... 2 Installation... 3 Calibration and Adjustments... 5 Maintenance Troubleshooting... 6 Plus 1 & Plus

More information

5001TCP SPEED CONTROLLER

5001TCP SPEED CONTROLLER INSTALLATION AND SETTING UP MANUAL 5001TCP SPEED CONTROLLER WARNING Disconnect all incoming power before working on this equipment. Follow power lockout procedures. Use extreme caution around electrical

More information

HT-DDD100 Digital Dual Driver Governor. Instruction manual

HT-DDD100 Digital Dual Driver Governor. Instruction manual Instruction manual Doc. No.: HT-DDD100_MN_DE_ Version: 1.2 Edition: Table of contents Installation declaration (for an incomplete machine)... 4 1 General... 5 1.1 Introduction... 5 1.2 Safety instructions

More information

5001TCP SPEED CONTROLLER

5001TCP SPEED CONTROLLER VARIABLE SPEED DRIVE CONTROLLER INSTALLATION AND SETTING UP MANUAL 5001TCP SPEED CONTROLLER With PC101 Torque Limit Control WARNING Disconnect all incoming power before working on this equipment. Follow

More information

CENTROIDTM. AC Brushless Drive. Product Spec Sheet

CENTROIDTM. AC Brushless Drive. Product Spec Sheet 4 Axis, up to 2 KW motors Brake Output for each axis Overtemp and Overcurrent Protection All-software Configuration Self-cooled Fiber Optic Control CENTROIDTM AC Brushless Drive Product Spec Sheet AC Brushless

More information

Product Manual (Revision A, 8/2015) Original Instructions. ProAct II Digital Speed Control System. Technical Supplement

Product Manual (Revision A, 8/2015) Original Instructions. ProAct II Digital Speed Control System. Technical Supplement Product Manual 36060 (Revision A, 8/2015) Original Instructions ProAct II Digital Speed Control System Technical Supplement DEFINITIONS This is the safety alert symbol. It is used to alert you to potential

More information

INSTRUCTION MANUAL FOR VOLTAGE REGULATOR APR P/N

INSTRUCTION MANUAL FOR VOLTAGE REGULATOR APR P/N INSTRUCTION MANUAL FOR VOLTAGE REGULATOR APR 125-5 P/N 9168800100 Publication: 9168800990 Revision: J 03/09 INTRODUCTION This instruction manual provides information about the operation and installation

More information

ATB Series - Integral Throttle Body Actuators

ATB Series - Integral Throttle Body Actuators ATB Series - Integral Throttle Body Actuators INTRODUCTION Low-Cost, Maintenance Free, Compact Design Various Bore Sizes Available (25-85mm) Precise, Real-Time Engine Speed Control Flexible Design for

More information

60 Series Engine Controls

60 Series Engine Controls ECU 60 Series Engine Controls Use CAUTION since you are applying 120VAC RMS to the AC Input terminals and that it is always potentially their during engine run!!! ECU is a registered trademark of Engineering

More information

ATOTH-G Series BLDC Motor Controller. User s Manual

ATOTH-G Series BLDC Motor Controller. User s Manual ATOTH-G Series BLDC Motor Controller User s Manual Contents Chapter One Summary...1 Chapter Two Main Features and Specifications.2 2.1 Basic Functions...2 2.2 Features... 5 2.3 Specifications...6 Chapter

More information

Engine Controls & Actuation

Engine Controls & Actuation Engine Controls & Actuation Model 0175, 0250, 0300 Series DYNA 2000 & 2500 Linear Actuator APECS 4500 Controller DPG Speed Controls L-Series Position Controller with Integrated Throttle Body (ITB) L-Series

More information

Cascade CD101 Auto-Start Controller. Installation and Operations Manual Sections 40 & 75

Cascade CD101 Auto-Start Controller. Installation and Operations Manual Sections 40 & 75 Cascade CD101 Auto-Start Controller Installation and Operations Manual 00-02-0594 2018-02-15 Sections 40 & 75 In order to consistently bring you the highest quality, full featured products, we reserve

More information

Application Note CTAN #234

Application Note CTAN #234 Application Note CTAN #234 The Application Note is pertinent to the Unidrive SP Family A Guide to Tuning the Unidrive SP Introduction: The Unidrive SP provides a number of features that greatly assist

More information

PED 5000 ELECTRIC ACTUATOR

PED 5000 ELECTRIC ACTUATOR ENGINE GOVERNING SYSTEMS PRODUCT INFORMATION BULLETIN JAN 2002 PED 5000 ELECTRIC ACTUATOR INTRODUCTION The PED 5000 electric actuator is a rotatory output, linear torque, proportional servo. This electromechanical

More information

Kelly KDHA High Voltage Series/PM Motor Controller User s Manual

Kelly KDHA High Voltage Series/PM Motor Controller User s Manual Kelly KDHA High Voltage Series/PM Motor Controller User s Manual KDH07500A KDH07501A KDH07700A KDH07701A KDH09400A KDH09401A KDH09500A KDH09501A KDH12400A KDH12401A KDH12500A KDH12501A KDH14300A KDH14301A

More information

Kelly HPM High Power Full Bridge Permanent Magnet DC Motor Controller User s Manual

Kelly HPM High Power Full Bridge Permanent Magnet DC Motor Controller User s Manual Kelly HPM High Power Full Bridge Permanent Magnet DC Motor Controller User s Manual HPM72601 HPM72801 HPM12401 HPM12601 HPM12801 HPM14301 HPM14501 HPM14701 Rev.3.4 Dec. 2016 Contents Chapter1 Introduction...

More information

GENSET CONTROL MODULE A121A / A241A

GENSET CONTROL MODULE A121A / A241A Technical Data Sheet GENSET CONTROL MODULE A121A / A241A Features: Models for both 12V and 24V systems. One model for both spark ignition and diesel engines. 4-alarm light outputs with lamp-test provisions.

More information

INSTRUCTION MANUAL FOR. VOLTAGE REGULATOR Model: APR Part Number:

INSTRUCTION MANUAL FOR. VOLTAGE REGULATOR Model: APR Part Number: INSTRUCTION MANUAL FOR VOLTAGE REGULATOR Model: APR 125-5 Part Number: 9 1688 00 100 Publication Number: 9 1688 00 990 Revision H: 07/2001 CONTENTS SECTION 1 GENERAL INFORMATION...1-1 DESCRIPTION... 1-1

More information

ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual

ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual Headquarters : No.3, Lane 201, Chien Fu St., Chyan Jenn Dist., Kaohsiung, TAIWAN Tel : + 886-7-8121771 Fax : + 886-7-8121775 URL : http://www.kutai.com.tw

More information

225 SERIES ELECTRIC ACTUATOR

225 SERIES ELECTRIC ACTUATOR Generator Control Specialists 48A Ainsdale Street Telephone: 0500 800 225 P.O. Box 30 West Chermside, Qld 4032 Facsimile: 3350 1654 Grange, Qld 4051 Australia Mobile: 0427 22 00 18 Australia email: info@powersystems.com.au

More information

TCwin AND THE STC THROTTLE CONTROLLER... 3 INSTALLATION... 3 SOFTWARE INSTALLATION... 3 DEFINITION OF TERMS... 4 MAP EDITING KEYS... 4 DIAGNOSTICS...

TCwin AND THE STC THROTTLE CONTROLLER... 3 INSTALLATION... 3 SOFTWARE INSTALLATION... 3 DEFINITION OF TERMS... 4 MAP EDITING KEYS... 4 DIAGNOSTICS... 1 TCwin AND THE STC THROTTLE CONTROLLER... 3 INSTALLATION... 3 SOFTWARE INSTALLATION... 3 DEFINITION OF TERMS... 4 MAP EDITING KEYS... 4 DIAGNOSTICS... 5 WARNING LIGHT FLASH PATTERNS... 6 HOLDING PWM MAP...

More information

INTECH Micro 2300-RTD6

INTECH Micro 2300-RTD6 INTECH Micro 2300-RTD6 6 Channel RTD Input Station Overview. The Intech Micro 2300 Series is a system of modular I/O Remote Stations, that add an even lower cost option to Intech s already extensive intelligent

More information

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI II 1400-6 ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI ACSI 1426-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1092, REV. C INSTALLATION For C-UL Listed applications,

More information

DGC-2020 DIGITAL GENSET CONTROLLER

DGC-2020 DIGITAL GENSET CONTROLLER DIGITAL GENSET CONTROLLER Basler Electric s Digital Genset Controller (DGC-2020) is a highly advanced integrated genset control system. The DGC-2020 is perfectly focused, combining rugged construction

More information

Product Guide: Series III Pump Control Board Set (RoHS)

Product Guide: Series III Pump Control Board Set (RoHS) revised 04/08/10 Description: The Series III Pump Control Board Set provides motor drive and pump control for a wide assortment of pumps from Scientific Systems, Inc. The assembly consists of two circuit

More information

Model H30 Operation Manual

Model H30 Operation Manual Model H30 Operation Manual Model H30 Version 1.0 August 1, 2007 2 135 West Davenport Street Rhinelander WI 54501 Phone: 866.441.7997 Fax: 866.278.0036 info@houstonst.com www.houstonst.com 3 Table of Contents

More information

395693 8:237/ D8)- 04B)'("F8 06B 4E37 B0D6: 1:9DB:7 8:2E73 AB:2E1D EC3B!C 5E623 F8(',(.,&,(&(( PRODUCT USER GUIDE A,=B@>5C4B:>= 023;6 >7 T>=B6=BA! I.@>5C4B12@:2B:>=A 0 L -', 6;F EYWMbLa GNTNLaRWV 8TJYRORLJaRWV

More information

PowerOhm Installation Manual for BM R Series Braking Modules

PowerOhm Installation Manual for BM R Series Braking Modules PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

Product Manual (Revision C) Original Instructions. EPG (Electric Powered Governor) with Position Feedback. Installation and Operation Manual

Product Manual (Revision C) Original Instructions. EPG (Electric Powered Governor) with Position Feedback. Installation and Operation Manual Product Manual 82354 (Revision C) Original Instructions EPG (Electric Powered Governor) with Position Feedback Installation and Operation Manual General Precautions Read this entire manual and all other

More information

PowerOhm Installation Manual for LG ATV Series Braking Modules

PowerOhm Installation Manual for LG ATV Series Braking Modules PowerOhm Installation Manual for LG ATV Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

GENSET CONTROL MODULE LEVEL 1 A121CM / A241CM. Special logic to re-establish cranking following a false start.

GENSET CONTROL MODULE LEVEL 1 A121CM / A241CM. Special logic to re-establish cranking following a false start. Technical Data Sheet GENSET CONTROL MODULE LEVEL 1 A121CM / A241CM Features: Models for both 12V and 24V systems. One model for both spark ignition and diesel engines. 5-alarm light outputs with lamp-test

More information

Subject Underhood G System Error Codes and Symptoms System or Parts affected

Subject Underhood G System Error Codes and Symptoms System or Parts affected System or Parts affected Index Underhood70G (V90Gxxx) System or Parts affected... 1 Overview... 1 Identifying your System... 1 Retrieving Logged Error Messages... 1 Error Messages... 3 Error Message Table...

More information

Full Bridge Permanent Magnet DC Motor Controller User's Manual

Full Bridge Permanent Magnet DC Motor Controller User's Manual www.igreatway.com Email:info@igreatway.com V 3.3 Full Bridge Permanent Magnet DC Motor Controller User's Manual PM24101 PM24201 PM24301 PM36101 PM36201 PM48101 PM48201 PM48301 PM48401B PM48501B PM72101

More information

Kelly KDC Series/PM Motor Controller User s Manual

Kelly KDC Series/PM Motor Controller User s Manual Kelly KDC Series/PM Motor Controller User s Manual KDC48600 KDC48601 KDC48602 KDC48603 KDC72600 KDC72601 KDC72602 KDC72603 KDC72800 KDC72801 KDC72802 KDC72803 KDC12602 KDC12603 Rev.3.3 May 2011 Contents

More information

TTT802 Gearshift Controller, Part # R1N-S (Standard), -P (Paddleshift)

TTT802 Gearshift Controller, Part # R1N-S (Standard), -P (Paddleshift) First, Sign and Date Bln 2009-03-9 Updated, Sign and Date Bln 200-04-29 (0) User Manual TTT802 Gearshift Controller Firmware for R--N-2- TTT802 Gearshift Controller, Part # 2-620-9-RN-S (Standard), -P

More information

Filtered PWM Speed Control for Permanent Magnet DC Motors

Filtered PWM Speed Control for Permanent Magnet DC Motors Instructions for Installation and Operation Filtered PWM Speed Control for Permanent Magnet DC Motors Model 0794 Speed and Direction Control up to 5/8 HP NEMA-1/IP-20 Specifications Product Type:... WPM-2148E1

More information

ALR Series Electronic Linear Actuators

ALR Series Electronic Linear Actuators 1 The ALR Series Actuator is designed to replace the OEM equipped shut down solenoid. To properly install the ALR actuator, a precise measurement must be obtained from the removed OEM equipped shutdown

More information

ECU. Speed Switch Manual. Contents. ECU is a registered trademark of Engineering Concepts Unlimited Inc.

ECU. Speed Switch Manual. Contents. ECU is a registered trademark of Engineering Concepts Unlimited Inc. ECU Speed Switch Manual Contents ECU is a registered trademark of Engineering Concepts Unlimited Inc. Contents Unit review Magnetic pickup example AC input example Design Guide Troubleshooting guide 24

More information

C1 Controller & Driver. User s Guide

C1 Controller & Driver. User s Guide Controller & Driver User s Guide Page 1 of 12 Table of Contents Warnings & Notices 2 Quick Start Procedure 3 Factory Default Settings 4 System Setup Position 5 Force 5 Pressure 5 Flow 6 Wiring 7 Potentiometers/Tuning

More information

Product Manual (Revision B) Original Instructions. EPG Electrically Powered Governor Models 501 and Installation and Operation Manual

Product Manual (Revision B) Original Instructions. EPG Electrically Powered Governor Models 501 and Installation and Operation Manual Product Manual 82448 (Revision B) Original Instructions EPG Electrically Powered Governor Models 501 and 1701 Installation and Operation Manual General Precautions Read this entire manual and all other

More information

701 Digital Speed Control for Reciprocating Engines. Product Manual (Revision D) Original Instructions

701 Digital Speed Control for Reciprocating Engines. Product Manual (Revision D) Original Instructions Product Manual 85177 (Revision D) Original Instructions 701 Digital Speed Control for Reciprocating Engines 9903-466, 9905-211, 9905-212, 9905-213, 9905-214, 9905-215, 9905-216, 9905-457 Installation and

More information

Installation and Maintenance Instructions. World Leader in Modular Torque Limiters. PTM-4 Load Monitor

Installation and Maintenance Instructions. World Leader in Modular Torque Limiters. PTM-4 Load Monitor World Leader in Modular Torque Limiters Installation and Maintenance Instructions PTM-4 Load Monitor 1304 Twin Oaks Street Wichita Falls, Texas 76302 (940) 723-7800 Fax: (940) 723-7888 E-mail: sales@brunelcorp.com

More information

Product Manual (Revision D, 5/2015) Original Instructions. 2301A Speed Control. Installation and Operation Manual

Product Manual (Revision D, 5/2015) Original Instructions. 2301A Speed Control. Installation and Operation Manual Product Manual 82020 (Revision D, 5/2015) Original Instructions 2301A Speed Control Installation and Operation Manual General Precautions Read this entire manual and all other publications pertaining to

More information

MB A 12V/24V DC PROGRAMMABLE DUAL BATTERY ISOLATOR

MB A 12V/24V DC PROGRAMMABLE DUAL BATTERY ISOLATOR MB-3688 120A 12V/24V DC PROGRAMMABLE DUAL BATTERY ISOLATOR User Manual Warning and Precautions MB-3688 is built with corrosion resistant material and the main electronic assembly is well sealed inside

More information

LIPPERTCOMPONENTS, INC.

LIPPERTCOMPONENTS, INC. LIPPERTCOMPONENTS, INC. SCHWINTEK INWALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL Contents I. Controls 1-1 System components 1 1-1A versions C1 & C2 2 1-2 Motor wiring harness connections 3 1-3 Extend

More information

Dynamic Adjustment Procedure for 700-series Digital Controls. Application Note (Revision A,8/1998) Original Instructions

Dynamic Adjustment Procedure for 700-series Digital Controls. Application Note (Revision A,8/1998) Original Instructions Application Note 01304 (Revision A,8/1998) Original Instructions Dynamic Adjustment Procedure for 700-series Digital Controls (700, 701, 701A, 702, 705, 721, 723, 723PLUS, 828) General Precautions Read

More information

ES52. Auto Start Engine Controller. Full Version. Installation and User Manual for the ES52 Auto Start Engine Controller.

ES52. Auto Start Engine Controller. Full Version. Installation and User Manual for the ES52 Auto Start Engine Controller. ES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller. Full Version File: MAN-0001 R4.0, ES52 User Manual.doc Date: August 2017 Thank You For Purchasing

More information

Installation and Operating Manual. ActuCOM R8 IOM 8-18

Installation and Operating Manual. ActuCOM R8 IOM 8-18 Installation and Operating Manual Table of Contents 712 Trumbull Avenue Girard, Ohio 44420 1 General Information...4 1.1 Purpose and Scope...4 1.2 Audience...4 1.3 Intended Applications...4 1.4 Basic Control

More information

SALDET SALES & SERVICE, INC. CLINTON TOWNSHIP, MICHIGAN

SALDET SALES & SERVICE, INC. CLINTON TOWNSHIP, MICHIGAN Form 1254 BRAKETRON Electronic Motor Brake Instructions SALDET SALES & SERVICE, INC. CLINTON TOWNSHIP, MICHIGAN TABLE OF CONTENTS SECTION TITLE PAGE I. Introduction 1 II. Specifications 1 III. Principles

More information

Continental Hydraulics Installation Manual CEM-AA-A

Continental Hydraulics Installation Manual CEM-AA-A Continental Hydraulics Installation Manual CEM-AA-A Description: This power amplifier drives either single or dual solenoid proportional valve coils up to 2.6A. It is suitable to control current to proportional

More information

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery

More information

Small Full Bridge Permanent Magnet Motor DC Controller User Manual

Small Full Bridge Permanent Magnet Motor DC Controller User Manual Small Full Bridge Permanent Magnet Motor DC Controller User Manual SPM24051X SPM24101X SPM24121X SPM48051X SPM48101X SPM48121X SPM72051X SPM72101X SPM72121X SPM48151E SPM48181E SPM48221E SPM72151E SPM72181E

More information

Induction Power Supplies

Induction Power Supplies Induction Power Supplies 7.5kW; 135 400kHz 480V version (Integral Heat Station) User s Guide Model 7.5-135/400-3-480 SMD Control Brds Rev. D 5/08 Table of Contents 1. Specifications and features...3 2.

More information

Intelligent Hyper Speed Governor. Instruction manual

Intelligent Hyper Speed Governor. Instruction manual HT-HSG100 Instruction manual Doc. No.: HT-HSG100_MN_EN_ Version: 1.2 Edition: PC Software Version: 3.0.0.82 Firmware Version: 1.51 Hardware Version: D HUEGLI TECH AG (LTD) Switzerland Version: 1.2 Operating

More information

ES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller.

ES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller. ES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller. Full Version File: ES52rev2.63.doc October 24, 2006 2 Thank You For Purchasing This DynaGen Product

More information

Devices Supported: KEB48220 KEB48221 KEB48300 KEB48301 KEB48400 KEB48401 KEB48600 KEB48601 KEB72330 EB KEB72450 KEB EB KEB72600 KEB

Devices Supported: KEB48220 KEB48221 KEB48300 KEB48301 KEB48400 KEB48401 KEB48600 KEB48601 KEB72330 EB KEB72450 KEB EB KEB72600 KEB Kelly KEB Brushless Motor Controller User s Manual Devices Supported: KEB48220 KEB48221 KEB48300 KEB48301 KEB48400 KEB48401 KEB48600 KEB48601 KEB72330 KEB EB72 72331 KEB72450 KEB EB72 72451 KEB72600 KEB

More information

Service Manual Model S800 Smart Stand

Service Manual Model S800 Smart Stand Service Manual Model S800 Smart Stand Form #1-146 Rev. 10/3/13 Table of Contents Parts Breakdown 3 Monthly Maintenance Checklist 7 Smart Stand Operating Instructions 9 Scale Calibration 10 Advanced Smart

More information

PM300 VOLTAGE REGULATOR INSTRUCTION MANUAL

PM300 VOLTAGE REGULATOR INSTRUCTION MANUAL PM300 VOLTAGE REGULATOR INSTRUCTION MANUAL INTRODUCTION The PM300 voltage regulator is an encapsulated electronic voltage regulator that controls the output of a brushless AC generator by regulating the

More information

ABB Component Drives ACS150, 0.5 to 5 Hp

ABB Component Drives ACS150, 0.5 to 5 Hp ABB Component Drives ACS150, 0.5 to 5 Hp Technical Catalog BUSINESS PROFILE INDUSTRIES PRODUCTS APPLICATIONS EXPERTISE PARTNERS SERVICES Contents Choice 1: Simply contact your local ABB drives sales office

More information

Overview of operation modes

Overview of operation modes Overview of operation modes There are three main operation modes available. Any of the modes can be selected at any time. The three main modes are: manual, automatic and mappable modes 1 to 4. The MapDCCD

More information

ACCESSORY KIT INSTALLATION INSTRUCTIONS

ACCESSORY KIT INSTALLATION INSTRUCTIONS ACCESSORY KIT INSTALLATION INSTRUCTIONS Low Ambient Accessory For Air Cooled Split-System Air Conditioners YD360/480/600, YJ-30/-40/-50 and J30/40/50 YD Models 642546-UAI-A-080 GENERAL Standard operation

More information

Service Manual. Model L500 and L600 Smart Lift. WARNING: Cancer and Reproductive Harm - Form #1-144 Rev.

Service Manual. Model L500 and L600 Smart Lift. WARNING: Cancer and Reproductive Harm -   Form #1-144 Rev. Service Manual Model L500 and L600 Smart Lift WARNING: Cancer and Reproductive Harm - www.p65warnings.ca.gov. Form #1-144 Rev. 2/5/19 Table of Contents Parts Breakdown 3 Monthly Maintenance Checklist 5

More information

Service Manual Model S400 and S500 Smart Stand

Service Manual Model S400 and S500 Smart Stand Service Manual Model S400 and S500 Smart Stand Form #1-145 Rev. 10/3/13 Table of Contents Parts Breakdown 3 Monthly Maintenance Checklist 7 Smart Stand Operating Instructions 9 Scale Calibration 10 Advanced

More information

Service Manual Model L1000 Smart Lift

Service Manual Model L1000 Smart Lift Service Manual Model L1000 Smart Lift Form #1-147 Rev. 10/1/13 Table of Contents Parts Breakdown 3 Monthly Maintenance Checklist 5 Smart Lift Operating Instructions 7 Scale Calibration 8 Advanced Smart

More information

HGM1780 AUTOMATIC GENERATOR MODULE CONTENT 1. SUMMARY PERFORMANCE AND CHARACTERISTICS SPECIFICATION OPERATION...

HGM1780 AUTOMATIC GENERATOR MODULE CONTENT 1. SUMMARY PERFORMANCE AND CHARACTERISTICS SPECIFICATION OPERATION... CONTENT 1. SUMMARY...4 2. PERFORMANCE AND CHARACTERISTICS...4 3. SPECIFICATION...5 4. OPERATION...6 4.1. DISPLAY PANEL...6 4.2. LCD ICON INSTRUCTION...7 4.3. DISPLAY INSTRUCTIONS...7 4.4. DISPLAY DESCRIPTION...8

More information

2301A Load Sharing & Speed Control with Dual Dynamics. Product Manual (Revision NEW, 1990) Original Instructions

2301A Load Sharing & Speed Control with Dual Dynamics. Product Manual (Revision NEW, 1990) Original Instructions Product Manual 82046 (Revision NEW, 1990) Original Instructions 2301A Load Sharing & Speed Control with Dual Dynamics Installation and Operation Manual General Precautions Read this entire manual and all

More information

PowerOhm Installation Manual for BM R Series Braking Modules

PowerOhm Installation Manual for BM R Series Braking Modules PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

HGM1750 Genset Security Module USER MANUAL Smartgen Technology

HGM1750 Genset Security Module USER MANUAL Smartgen Technology HGM1750 Genset Security Module USER MANUAL Smartgen Technology CONTENT 1. SUMMARY... 4 2. PERFORMANCE AND CHARACTERISTICS... 5 3. SPECIFICATION... 7 4. OPERATION... 8 5. PROTECTION... 9 6. PARAMETER RANGE

More information

EPG Electrically Powered Governor. Installation and Troubleshooting Manual. Models 1712/1724 and 512/524 without Position Feedback

EPG Electrically Powered Governor. Installation and Troubleshooting Manual. Models 1712/1724 and 512/524 without Position Feedback Installation and Troubleshooting Manual EPG Electrically Powered Governor Models 1712/1724 and 512/524 without Position Feedback Manual 82329 (Revision J) WARNING DANGER OF DEATH OR PERSONAL INJURY WARNING

More information

CONTROL FEATURES AVAILABLE OPTIONS

CONTROL FEATURES AVAILABLE OPTIONS Vari Speed A2000 TABLE OF CONTENTS Control Features Options Application Data Operating Condition s Control Ratings Chart Mounting Dimensions Installation and Wiring Typical Wiring Diagram Schematic (Block

More information

UL/cUL FILE NUMBER E CE See last page of manual for CE Declaration of Conformity.

UL/cUL FILE NUMBER E CE See last page of manual for CE Declaration of Conformity. INSTALLATION, OPERATION and MAINTENANCE MANUAL MODEL SCPF1 15, 25, 40 & 65 AMP SCR POWER CONTROLS UL/cUL FILE NUMBER E151547 CE See last page of manual for CE Declaration of Conformity. AMETEK HDR POWER

More information

HGM1770 Automatic Generator Control Module OPERATING MANUAL Smartgen Electronic

HGM1770 Automatic Generator Control Module OPERATING MANUAL Smartgen Electronic HGM1770 Automatic Generator Control Module OPERATING MANUAL Smartgen Electronic CONTENT 1. SUMMARY... 4 2. PERFORMANCE AND CHARACTERISTICS... 4 3. SPECIFICATIONS... 5 4. OPERATION... 6 5. PROTECTION...

More information