DORMA Gmbh + Co. KG Postfach 4009 D Ennepetal Telefon (02333) 7930

Transcription

1 1 DG 0 89 I x x x x /1 1 T Index: Screw chart Tools required Glass preperation Outside trim options Device installation Optional bottom strikes Rod cutting Rod ext ension Cy linder dogging opt ion PT30SPL glass prep Z Note: One set of f ixing instructions should be left with building owner after device has been installed. EN 1125 C LASSIFICATION NUMBER FOR THIS PRODUCT B A 9800FL AAA D ORMA Architectural Hardware 1003 West Broadway Steeleville, IL BS EN 1125 : 2008 European Norm Standard for Panic Exit Devices Operated By A Horizontal Bar. Product Classification 3,7,6,0,1,3,2,2,B,A Certification Body Ref Nr : 1121 DORMA Gmbh + Co. KG Postfach 4009 D Ennepetal Telefon (02333) 7930

2 (2) 1/4i20 x 1 1/2" (38mm) F.H.P.M. (12i15mm glass) Chassis M ounting (2) 1/4i20 x 1 1/4" (32mm) F.H.P.M. (10i12mm glass) (2) 10i32 x 3/8" (10mm) R.H.P.M. End Cap Bracket (3) 10i32 x 3/8" (10mm) P.H.P.M. Bolt To Door (3) 10i32 x 3/8" (10mm) P.H.P.M. Bolt To Door (2) 8i32 x 1/2" (13mm) R.H.P.M. Rod Retaining Clip M ount (2) M 5 O.H.P.M. ( M etal) #AD426 Keep P ack (2) #12 x 25 F.H.P. T. (Wood) #AD426 Keep P ack #AD439 Bottom Keep (Cement or Grout In P lace) (10) 8i32 x 1/4" (6mm) F.H.P.M. Chassis Cover, End Cap & Latch Covers (2) 8i32 x 3/8" (9. 5mm) F.H.P.M. End Cap M ounting (2) #10 x 25 F.H.P. T. End Cover M ounting 2

3 Note: If device is to be installed over glass lite panels, shim kit may be required, order GK9200. Outside Gaskets Inside patch fitting Outside patch fitting Glass Inside bushings Top bolt patch fitting assembly, mounting screws provided with patch fitting. Outside Gaskets Inside patch fitting Gaskets Outside patc h fitting Glass bus hings Inside Chassis spacer Glass bushings Chassis patch fitting assembly mounting screws provided with chassis assembly outside trim required. End cap fitting assembly, mounting, screws provided with patch fitting. Note: Patch fitting torque of no more then 12Nm for attachment to glass door. Outside Outside patch fitting Glass bushings Gaskets Inside patch fitting Inside Bottom bolt patch fitting assembly, mounting screws provided with patch fitting. Note: If device is to be installed over glass lite panels, shim kit may be required, order GK9200. Read the entire instruction sheet prior to installation. Before Installing Hardware: 1. Verify door width, handing and product with carton label for correct exit device and length. (See Step 1) 2. For hand reversal of chassis see page 6, for outside lever trim see page (5). 3. For less bottom rod device, delete bottom latch installation steps. Note: Less bottom rod device is not recommended where security is a primary concern. M5 Ë Tap, M6 Ë Tap Drill bits: 3.8mm, 4.2mm, 10mm, 13mm, 25mm & 38mm 5/32" Allen wrench for lever trim. Cross point screw driver Hack saw 3

4 Note: If device is to be installed over glass lite panels, shim kit may be required, order GK mm 53.5 mm 45 mm 20 mm 2 Places 70 mm 36.5 mm 22.5 mm 45 mm 16 mm 3 Places 20 mm 2 Places 1106 mm 1011 mm 915 mm 45 mm 37 mm 20 mm 2 Places Finshed floor or t hreshold 6 mm 4

5 LHRB TRIM SHOWN RHRB OPPOSITE ZODTTGD ZK23TGD ZK08/ 09EPTGD ZR23TGD ZR08/ 09EPTGD Tig hten Securely IMPORTA NT Note: All lever handles except for "clutch" are shipped unattached. T o install; Place handle in desired position and attach with allen screw located in back of trim plate. 5/32" Allen wrench required. T o change hand on "clutch" trim rotate and "break" lever around to desired hand. IMPORTA NT NOT E: Standard tail piece as shipped will fit 13 É 15mm thick glass. For 10 É 12 mm glass it will have to be shortened by approximately 3mm. See below. 3 mm All trims are free wheeling. (Handle will rotate when locked. ) Remove for 10mm glass thickness. Fixing of "EP" cylinder Insert "EP" cylinder into adapter, secure wit h set screw supplied with cylinder. Insert adapter/ cyilnder assembly thru trim and secure assembly wit h (2) 8 œ 32 screws as shown. F or "09" function (key only re œ movable when locked) insert addtional 8 œ 32 screw as shown. 09 Function Screw "EP" adapter Cy linder Mount ing Screw (2) 5

6 DISA SSEMBLE RHR (Rig ht Hand Reverse) REASSEMBLE LHR (Left Hand Reverse) Rotate chassis 180 Degrees d a c b e f g L onger leg down. Once handing of d oor has been ver ified with chassis assembly, install chassis and ou tside tri m to push side of d oor us ing bushings, gaskets and spacer as show n be low, secure with screws provided. Note: Patch fitting torque of no more then 12Nm for attachment to glass door. Chassis spacer (1) Chassis backplate (1) (2) 1/4 20 x 1 1/2"(38mm) F.H.P.H.M.S. Gaskets (2) Glass bushings (3) 6

7 Prepare to install touch bar and rail on door. NOTE: Verify strikes, stile width, any trim and stop height prior to making any cuts. Cutting is required for glass door applications. Size AA: Fits 1220mm door opening with minor cutting. Can be cut to fit a 838mm minimum door opening. Size BB: Fits 915mm door opening with minor cutting. Can be cut to fit a 686mm minimum door opening. Size CC: Fits 915mm door opening with minor cutting. Using a shorter touch pad then the standard "BB" Standard factory rail length. A = 1105mm B = 800mm C = 800mm D = 800mm size allows it to be cut to 610mm door opening. Verify device length with box label; "AA", "BB" or "CC", ie. 9800FLTGD BB Example: C L CL Fixing Cent res 36mm "X" 1mm Cutting length "X" = Fixing centre  37mm Note: Glass door applications will require cutting of the standard length "FL" touch bar and rail assembly. Depress touch bar as shown, tape and cut to length as shown Touch bar. should be approximately 5mm longer then rail once it is released to upward position. Filler Touch bar and rail assembly Tape 5mm 47mm Install rear end cap patch fitting and s as shown below, secure with screws provided in asembly pack. Outside Outside patch fitting Gaskets (2) Glass bushings (2) I nside I nside patch fitting 7 Note: Patch fitting torque of no more then 12Nm for attachment to glass door.

8 Install touch bar and rail assembly and end cap to door. Remove two 8ã32 screws from chassis, slide touch bar and rail assembly under rear of chassis. I nstall (2) two 8ã32 x 10mm P.H. P. M. to secure touchbar to chassis. Bracket should be flush aga inst patch fitting and tight against rear of rail. H ol d rear mounting bracket tightly against door and rear of rail. Secure with proper fasteners. (2) 8ã32 x 10mm P.H. P. M. "Remove protective ing from the touchbar and rail assembly prior to installing on door." 8

9 Install top and bottom patch fitting assemblies to door as shown below, secure with screws provided in assembly packs. Note: Patch fitting torque of no more then 12Nm for attachment to glass door. Gaskets (2) Outside Inside patch fitting Outside patch fitting Inside Glass bushings (2) Gaskets (2) Outside Inside patch fitting Outside patch fitting Inside Glass bushings (2) 9

10 Install top latch assembly and bottom slide bolt assembly to patch fittings on door. S ecure with (3) 10t32 x 3/8" (10mm) P.H. P.H.M.S. as shown. (3) 10t32 x 3/8" (10mm) P.H. P.H.M.S. (3) 10t32 x 3/8" (10mm) P.H. P.H.M.S. 10

11 Install top rod and adjust top latch assembly. Rods shipped cut to length for 2134mm door opening. O ptional 2438mm door opening available, ( must be requested at time of ordering). F or doors over 2438mm and up to 3048mm request "ETR" package at time of ordering. F or top rod length other than "standard" see chart below. O rder 2438mm option and cut to length. D epress tripping lever and ensure that top latch is fully extended and in dead locked position. B o lt should not be able to be depressed. B e ll crank of chassis should be com pletly dow n in home position. Thread top rod onto adjusting bolt until hole in bottom of rod aligns with hole in rear of top portion of bellcrank, bottom of rod should sit on top of bell crank. Insert leg of retaining plate through hole in rod and hole in bellcrank, install x 1/2" (13mm) screw and tighten securely. NOTE: If horizontal reference line is moved from the recommended mounting height, new rods may have to be ordered. Remove 8/32 x 13mm phillips head screw from ret aining plate as shown. If cutting is required "Do Not Cut Threaded End". (S ee Chart) below, and cutting instructions on page15. Use supplied drill jig and 4. 3mm drill bit if new hole is required. 2134mm Standard Top Rod 895mm 2438mm Optional Top Rod 1200mm 610mm "ETR" Extended top DOOR HEIGHT TOP ROD LENGTH 2032mm 794mm 2083mm 845mm 2134mm 895mm 2184mm 946mm 2235mm 997mm 2286mm 1048mm 2337mm 1099mm 2388mm 1149mm 2438mm 1200mm rod extension. "D o no t cut." 11

12 Check for proper function of device and top latch assembly. Depress touch bar slowly, top latch bolt should retract fully. Hold bar depressed, push in and hold top tripping lever. Latch bolt should be flush or slightly depress in top latch case. If this is found, release touch bar and tripping lever top latch bolt should remain captured by tripping lever. Push in on tripping lever and release top latch bolt, bellcrank should drop completely down and top latch should be fully extended and dead locked. (You should not be able to push the bolt in. ) If top bolt does not retract fully or can be pushed in, adj ustment of top rod is rel quired: Remove 8l3 2 screw and retaining plate; rotate rod left (clocklwise) to lengthen, half turns at a time. Relinstall retaining plate and screw; check for dead lock after each turn. Install top keep. See spotting templates located in rear of booklet if not already done. Check for proper alignment and operation with top latch after installation. #10 x 25 F.H.P.T.S. (Wood) M5 O.H.P.M.S. (Metal) 16mm 38mm 32mm 27mm 38mm #AD426 St rike #AD426A Strike w ith optional transom mount 12

13 Installation of bottom slide bolt or latch assembly. NOTE: If horizontal reference line is moved from the recommended mounting height, new rods may have to be ordered. If cutting is required "Do Not Cut Threaded End". Use supplied drill jig and 4. 3mm drill bit if new hole is required. Remove 8/32 x 13mm phillips head screw f rom retaining plate as shown. Thread bottom rod approximately 1/2 way on to slide bolt assembly. With bell crank down and top latch fully extended and dead locked. Insert rod and slide bolt assembly in to bottom latch bracket as shown, rotate rod until hole in rod aligns with hole in bell crank. Insert retaining clip and secure with 8 32 x 13mm screw. Bottom rod 851mm Check to see that there is approximately 16mm of bolt hanging down and that bolt moves up and down freely in latch case. With bell crank down and top latch fully extended and dead loc ked. Aprox. 16mm F or o ptional pullman latch: Thread rod approximately 1/2 way on to adjusting bolt, tilt rod upward, rotate rod clock? w ise to shorten, counter clock? w ise lengthen until hole in rod aligns with hole in bell crank. Bolt should be dead locked when down just as top bolt. A djust rod until dead lock is achieved. Installation of standard bottom keep. F or additional keep installations see page 15. No. AD 439 Keep 25mm 6mm Ref. Finished floo r Edge of door 19mm Note: Drill 19m dia. hole x 25mm deep. (Grout in place) 15mm 15mm 5mm ref. 13mm C L Edge of door See device te mplate 13

14 Verification of rod adjustments. Top latch should be fully extend and dead latched as shown and bell crank should drop completely down. B. A. Block open door, push inward on tripping lever and release top latch bolt as shown. Check for dead lock by attempting to push downward on top latch bolt (it should not push in). "Only" if it can be pushed in adjust rods per step below. C. To adjust: Re move 8Œ32 screw, reœ move retaining plate, rotate top rod right (counter clockœwise) to shorten and left (clockœwise) to lengthen. Rotate half turns at time, reðinstall retaining plate and screw after each turn and check for dead lock of top latch bolt. G. Close door and check that top and bottom latch bolts align and engage in top and bottom strikes. H. After rods are fully adjusted ensure that top and bottom rod retaining plate screws are tight. I. Check device operat ion by opening and closing door several times from inside. Check and operate outside trim if installed. Repeat rod adjustment procedure if: Top latch is not held retracted Bottom slide bolt does not clear strike or floor. Latches do not work properly with outside trim J. Install end cap, center case and latch s. (2) 8 ¼3 2 x 6mm P.H.F.H.U.C.M.S. (2) #10 x 25mm F.H.P.T.S. (8) 8 ¼3 2 x 6mm P.H.F.H.U.C.M.S. Flush D. Depress and hold touch bar. Push in on tripping lever and hold depressed, check position of top latch bolt. It should be flush to slightly depressed in top latch bracket. E. Release t ripping lever and touch bar, top latch should reœ main in retracted posit ion K. Standard hex key dogging, depress touch bar insert supplied hex key and rotate clock wise to dog and counter clock wise to undog. Slide bolt clears strike F. With top latch held retracted by t ripping lever, check bottom slide bolt to ensure it clears the strike, t hreshold, and floor by unblocking and swinging door. If adj ustment is required; follow same steps as in step C above for top rod until proper clearance is achieved. 14

15 #AD416 Keep Edge of door 4 6 mm 1 6 mm For surface strike drill (2) 8mm diameter x 25mm deep holes for anchors. 6 mm Ref. 15mm Finished floor #12 x 25mm F.H.P.T.S. Edge of door C L See device template for backset. 13mm Lead anchors 60 mm 5mm Ref. Top of threshold 15mm #AD431 Keep Edge of door 13mm 44mm Drill (2) 1 0 mm dia. holes x 51mm deep for anchors. #1/452 0 x 25 R.H.P.M.S. 1 6 mm 1 6 mm 13mm 15mm 1/4" Ref. Lead anchors Edge of door C See device L template for backset. Note: 42mm x 42mm max. square cutout x 25mm deep. #A D340 Strike 15mm NOTE: Drill 16mm dia. x 13mm deep min. for slide bolt. Edge of door 6mm Ref. Finished floor Edge of door C L 51mm 25mm For surface strike; drill (2) 8mm dia. x 25mm deep for anchors. Top of threshold 15mm 5 mm Ref. 13mm 15

16 NOTE: Rods shipped standard from factory for 2134mm seven foot door opening. Optional rod pack for 2438mm eight foot openings available "must be noted at time of order". For doors under 2134mm seven foot subtract difference from bottom of top rod, cut per details and redrill hole for retaining plate. For doors over 2134mm seven foot but under 2743mm nine foot a 610mm two foot rod extension "ETR" is available. Thread top rod and rod extension together, deduct difference, cut from bottom of top rod and redrill hole for retaining plate. "Do not cut Actual door opening height rod extension". For doors over 2438mm eight foot but under 3048mm ten foot the 610mm two foot rod extension "ETR" is added to the 2438mm eight foot rod pack. Thread top rod and rod extension together, deduct difference, cut from bottom of top rod and redrill hole for retaining plate. "Do not cut rod extension". NOTE: If horizontal reference line is moved from the reco mmended 1024mm height, new rods will have to be ordered. Drill Jig (Supplied) Tape "Do not cut threaded end" 4.3mm Drill Thru, use small hole in drill jig. For "ETR" (Extended Top Rod) devices. *Do not cut extension piece! C o nnecting link Thread rods t ogether securely. "Loctit e may be used for added security". Standard top rod 16

17 Cylinder specifications and cams; 17. 4mm Min 8mm 25. 4mm Mi n mm M ax. Note: When using IC core cylinders, ensure that cam is in proper position prior to installing the new core. Arrow Assa Best Corbin Falcon Useable Cams 001 Std. ( Yale) C136 A ' 3 Ilco/ Unican Lori Sargent Schlage Yale SC1 SC ' 8 2' Std. 13 ' 0664 or 13 ' Witness Marks Correct In'co rrect Cylinder dogging option on full length touch bar and rail; (See cam specifications above. ) To change cylinder: 1. R emove end cap, end & end cap mounting bracket. 2. R e move from chassis and two chassis to touch bar mounting screws. 3. R emove ( 6) touch bar to rail mounting screw from underside of rail. 4. Flip rear arm assembly outward from underside of touch bar. 5. R e move cylinder nut on underside of touch bar. 6. R emove cylinder and mounting plate. 6. Insert new cylinder facing as shown in detail. 7. Install mounting bracket and cylinder nut. 8. Flip rear arm assembly back under touch bar. 9. R e' i nstall touch bar to rail with ( 6) screws. 10. Install touch bar & rail back on to chassis with ( 2 ) screws. Note: DORMA mortise cylinder supplied. To use other manufacture cylinders, "L" less cylinder is available. 11. R e' i nstall end cap mounting bracket R e ' i nstall end cap, end & chassis. 17

18 Note: If device is to be installed over glass lite panels, shim kit may be required, order GK9200. R80 mm 37 mm 161 mm 148 mm 68 mm 36 mm R55 mm 3 mm 53.5 mm 20 mm 45 mm 20 mm 2 Places 135 mm 36.5 mm 22.5 mm 45 mm 16 mm 3 Places 20 mm 2 PLACES 1106 mm 1011 mm 915 mm 45 mm 37 mm 20 mm 2 Places Finshed floor or thres hold 6 mm 18

19 DORMA 9800FLTGD SURFAC E PANIC BOLT FIXING INST RUCT IONS This device is intended for use on single and/ or double outward opening panic ty pe doors. Category of project ion = Category 2 Field of door application = Cat egory A Maximum of 5mm door distort ion allow ed t o ensure saf e ex it. Maximum of a 1000N pulling f orce achieved against t he fix ing screw s. WA RNING The safety features of this product are essential to its compliance with EN 1125 (2008). No modification of any kind, other than those described in these instructions, is permitted. Panic devices manufactured in accordance with EN 1125 : (2008) will provide a high degree of safety and reasonable security provided they are fitted to doors and frames of equal quality and in good condition. The doors must be correctly hung and free from binding or any distortion. This device is not recommended for wood hollow core doors. IMPORTANT This equipment must be installed by a competent fitter. If these fixing instructions are not followed, then no responsibility for malfunction will be accepted by the manufacturer, and warrantee claims may be considered invalid. These fixing instructions must be passed to the user after installation has been completed. EN 1125 CLASSIFICATION NUMBER FOR THIS PRODUCT B A DOOR SIZES This product is suitable for doors up to Size A 838mm to 1220mm wide, 2500mm high. Size B 68 6mm to 915mm wide, 2500mm high. Size C 610mm to 915mm wide, 2500mm high. (Doors above 2500mm fall outside the scope of EN 1125) 200Kg door mass maximum.