Ultimate Electric Series Fryers

Transcription

1 Ultimate Electric Series Fryers Service & Parts Manual Frymaster Dean, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians. -Hour Service Hotline service@frymaster.com Price: $ APRIL 0

2 Please read all sections of this manual and retain for future reference. NOTICE This appliance is intended for professional use only and is to be operated by qualified personnel only. A Frymaster Dean Factory Authorized Servicer (FAS) or other qualified professional should perform installation, maintenance, and repairs. Installation, maintenance, or repairs by unqualified personnel may void the manufacturer s warranty. See Chapter of this manual for definitions of qualified personnel. NOTICE This equipment must be installed in accordance with the appropriate national and local codes of the country and/or region in which the appliance is installed. NOTICE TO U.S. CUSTOMERS This equipment must be installed in accordance with the appropriate national and local codes of the country and/or region in which the appliance is installed. NOTICE Drawings and photos used in this manual are intended to illustrate operational, cleaning and technical procedures and may not conform to onsite management operational procedures. NOTICE TO OWNERS OF UNITS EQUIPPED WITH CONTROLLERS U.S. This device complies with Part of the FCC rules. Operation is subject to the following two conditions: ) This device may not cause harmful interference, and ) This device must accept any interference received, including interference that may cause undesired operation. While this device is a verified Class A device, it has been shown to meet Class B limits. CANADA This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set out by the ICES-00 standard of the Canadian Department of Communications. Cet appareil numerique n emet pas de bruits radioelectriques depassany les limites de classe A et B prescrites dans la norme NMB-00 edictee par le Ministre des Communications du Canada. DANGER Improper installation, adjustment, maintenance or service, and unauthorized alterations or modifications can cause property damage, injury, or death. Read the installation, operating and service instructions thoroughly before installing or servicing this equipment.

3 DANGER The front ledge of the fryer is not a step. Do not stand on the fryer. Serious injury can result from slips or contact with the hot oil. DANGER Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. DANGER The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container at the end of frying operations each day. Some food particles can spontaneously combust if left soaking in certain shortening material. Additional information can be obtained in the filtration manual included with the system. WARNING No structural material on the fryer should be altered or removed to accommodate placement of the fryer under a hood. Questions? Call the Frymaster Dean Service Hotline at WARNING Do not bang fry baskets or other utensils on the fryer s joiner strip. The strip is present to seal the joint between the frypot. Banging fry baskets on the strip to dislodge shortening will distort the strip, adversely affecting its fit. It is designed for a tight fit and should only be removed for cleaning. NOTICE IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS MANITOWOC FOOD SERVICE EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID. FURTHER, FRYMASTER DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER.

4 Ultimate Electric Series Fryers Service & Parts Manual TABLE OF CONTENTS Page #. SERVICE PROCEDURES -. General -. Replace Computer/Controller -. Replace Interface Board -. Replace Transformer -. Replace Temperature Probe -. Replace Heating Element -.7 Replace High-Limit -9.8 Replace Frypot -0.9 Replace Contactor (Latching or Heating) -.0 Built-in Filter System Service Procedures -. Basket Lift Service Procedures -. Electric Interface Board Diagnostic Chart -7. Probe Resistance Chart -8. Element Wattage/Amperage Calculation Charts -8. Wiring Diagrams, Main /0V 7, 8E and 8UE -9.. FAST: 7, 8E and 8UE -0.. KSCFH8E FAST Export India V 8UE and EH V 8UE and EH7 -.. KSCFH8E -..7 BIH7 -. Wiring Diagrams, Basket Lifts -.. Modular Basket Lifts -.. Bell Crank Style Basket Lifts -7.7 Wiring Diagrams, Built-in Filtration V Systems V Systems /0V KFC Systems -0

5 Ultimate Electric Series Fryers Service & Parts Manual TABLE OF CONTENTS (CONT.) Page #. PARTS LIST -. Accessories -. Basket Lift Assembly (Modular) and Related Components -. Cabinetry and Related Components -.. EH7 & 8UE Electric -.. KFC8E Electric -8.. Door Components Spring-Loaded Door Pins -0.. Top Caps and Tilt Housing Components -. Computer and Related Components -. Contactor/Wireway Box and Related Components -. Filter Pan and Related Components -.. Under Fryer Filter (UFF) UFF 80 (00 Lb Capacity) -.. Under Fryer Filter (UFF) KFC8E Only -7.. Under Fryer Filter (UFF) KFC8E Export India Only -9.. Under Fryer Filter (UFF) Filter-Leaf/Suction Tube Assembly -0.. Single Under Fryer Filter (SUFF) BIH7 & 8UE -.7 Frypot and Drain Valve Components -.8 Oil Drain Flush Components -.9 Oil Drain Manifold Components -.0 Oil Return Manifold, Motor and Pump Components -. Oil Return Line Assemblies -8. Probes, High-Limits, Elements and Related Components -0. Tilt Safety Switch Components -

6 CHAPTER : SERVICE PROCEDURES. General Before performing any maintenance on your Frymaster Dean Ultimate Electric fryer, you must disconnect the electrical power supply. When electrical wires are disconnected, it is recommended that they be marked in such a way as to facilitate reassembly. DANGER Hot cooking oil or shortening will cause severe burns. Never attempt to move this appliance when filled with hot cooking oil or shortening, or to transfer hot cooking oil or shortening from one container to another. DANGER This equipment should be unplugged when servicing, except when electrical circuit tests are required. Use extreme care when performing such tests. This appliance may have more than one electrical power supply connection point. Disconnect all power cords before servicing. Inspection, testing and repair of electrical components should be performed by an authorized service agent only.. Replace Controller. Unscrew and remove two control panel screws on control panel front. Swing the panel open from the top.. Unplug wiring harness at plug on back of controller (arrow). Unplug controller ground wire from controller (circle).. Remove the control panel/controller by lifting the assembly from the hinged slots in the control-panel frame.. Reverse procedures to install new controller. Wire harness/connector and ground wire on controller back. -

7 CHAPTER : SERVICE PROCEDURES. Replace Interface Board. Unplug all power cords. Perform Procedure., Steps -, Replace Controller.. Unplug wire harness from the interface board (arrow). Remove all wiring from the terminals of the interface board, ensuring that each wire is marked for reattachment. Wire harness/connector.. Remove the nuts from each corner of the interface board and slide the board from the studs. Unplug connectors J and J, mark and unplug all other wiring on rear of the interface board. Ensure that standoffs remain in place on studs, prior to installing new interface board. Install the new interface board by reversing the previous procedures. Ensure that wire harnesses are connected to back of interface board prior to securing interface board. Also, ensure that wiring and wire harnesses are connected to the proper terminals. Nuts securing interface board (arrows). -

8 CHAPTER : SERVICE PROCEDURES. Replace Transformer. Unplug all power cords. Perform Procedure., Steps -, Replace Controller.. Remove all wiring from the terminals of the transformer to be replaced (arrows).. Remove the screws that secure the transformer to the component box.. Install the new transformer by reversing the preceding procedures. Make sure you reconnect the wiring to the proper terminals and the harnesses to the correct connectors.. Replace Temperature Probe. Unplug fryer from the electrical source.. Drain the cooking oil from the frypot.. Remove the fryer from the exhaust hood to gain access to the rear of the fryer.. Remove the screws from the back cover(s). Set the cover(s) and screws aside.. After removing back(s), remove two remaining screws securing the tilt housing cover (arrows). Remove the tilt housing. Mark and disconnect wiring from the transformer being replaced. Note: Early production model shown. Current production units have a one-piece back panel (remove all screws securing back panel). Older units have a three-piece back panel. Screws securing back cover and tilt housing. Remove two tilt-housing screws (arrows) after removing all other screws and back panel(s). -

9 CHAPTER : SERVICE PROCEDURES. Replace Temperature Probe (cont.). Disconnect the wire harness containing the probe wiring (arrows). It may be necessary to remove the wire ties. 7. Use a pin-pusher (P/N 80-8 or P/N see Section.7) to remove the red and white probe wires from the connector. Note probe pin location in plug. Pull the probe wires out of the insulation. Use a pin-pusher to remove probe wires from connector (arrows). 8. Remove the screw(s) securing the probe bracket to the element. Remove the metal wraps securing the probe to the element. Bracket Screw Probe Bulb Probe Bracket Remove probe bracket screw and bracket to remove probe. 9. Remove the probe bracket and the securing components from the probe bulb and element. Thread the probe wire through the hole (arrow) in the tilt plate assembly and remove the probe. Pull old probe wire through grommet to remove probe. -

10 CHAPTER : SERVICE PROCEDURES. Replace Temperature Probe (cont.) 0. Thread the new probe wire through the hole in tilt plate. Place the new temperature probe assembly onto the element and secure with the bracket and screws removed earlier. Clip the probe onto the rear of the element (arrow) in two places. The temperature probe assembly should be oriented in the same manner as the probe being replaced.. Thread the probe wires into the harness insulation. Note the pin positions and insert pins in the connector. Reconnect the harness and secure with a wire-tie.. Lower the element into the frypot with the lift handle. Secure probe bulb to the element back in two places with metal wire wrap (arrow).. Place the tilt housing cover over the tilt housing assembly and secure with screws. Slightly raising the elements will facilitate tilt-housing installation.. Install back cover(s) and secure with screws Install tilt housing and cabinet backs after probe installation is complete. -

11 CHAPTER : SERVICE PROCEDURES. Replace Heating Element. Perform Procedure., Replace Temperature Probe, Steps -7.. Unplug the element connectors for the element being removed (right element- -pin harness connector; left element- 9-pin harness connector). Remove the element wires from the connector. Press down on either side of the connector while pulling up on the top portion. The connector will open from the top. Note wiring configuration in connector before removing element wire pins. Pull all wires from the connector. Harness Connector Closed Push in on tabs to release top portion Top Portion Harness Connector Open. Remove the screws securing the temperature probe bracket from the element. Remove the probe clamp (metal wire-wrap). Set the temperature probe and probe-securing components aside. NOTE: Temperature probe removal is not required if the left element is being replaced. Remove metal wire wrap (arrow), and screws securing probe bracket to element (inset, arrow).. Disconnect the element springs from the tilt brackets. Disconnect element springs here. -

12 CHAPTER : SERVICE PROCEDURES. Replace Heating Element (cont.). Remove the element clamps and hardware before removing mounting-screws and nuts on the defective element. Remove all wireties securing element wiring, and then remove element from frypot.. Install the replacement element in the frypot and secure with the mounting hardware removed in Step. 7. Reinstall the temperature probe and probebracket components onto the replacement element. Element mounting screws on tilt-plate front. (Inset: element mounting plate on tilt-plate back.) 8. Route the element leads (terminals) to the rear of the fryer. Ensure the element-harness insulation is in place prior to installing connectors. Ensure element wire insulation is installed and that the wires are properly routed to prevent wire chafing. 9. Secure element wiring with wire-ties. Use wire-ties (arrows) to secure element wiring. -7

13 CHAPTER : SERVICE PROCEDURES. Replace Heating Element (cont.) 0. When replacing the left element (as viewed from the rear of the fryer), use the 9-pin connector, inserting the leads from the replacement element. Ensure the pin numbers match the numbers of the defective element wires. When all pin terminals have been fully inserted, close the connector by sliding the halves together until the tabs snap back into place (reverse procedure in this section, Step ). Check wire numbers to ensure correct wiring of the replacement element. When replacing the right element (as viewed from the rear of the fryer), follow the above procedure, inserting pin terminals into the corresponding holes in the -pin connector. Left Element 9-Pin Connector Right Element -Pin Connector. Connect the connectors, ensuring the latches lock in place (arrow).. Install the temperature probe wires (marked for re-assembly) in the corresponding pin locations. Ensure the connection is complete and the latches (arrow) are locked in place.. Reconnect the element springs. Older models have turnbuckles (arrow) to allow adjustment of the spring tension.. Place the tilt housing cover over the tilt housing assembly and secure with screws.. Install back covers and secure with screws.. Position fryer under exhaust hood. Older units have turnbuckles to adjust spring tension. Current production models are not adjustable. -8

14 CHAPTER : SERVICE PROCEDURES.7 Replace High-Limit. Perform Procedure., Replace Temperature Probe, Steps -.. Disconnect the wire harness containing the high-limit wires.. Use a pin-pusher (P/N 80-8 or P/N ) to remove the two high-limit wires from the wire harness connector (arrows). Note pin location in connector before removing wires.. Remove the high-limit from the frypot using an open-end wrench or other suitable tool.. Apply Loc-Tite PST 7 sealant to the replacement high-limit threads. Using a pin-pusher, remove two high-limit wires (arrows) from connector.. Screw the replacement high-limit into the frypot and tighten to inch-pounds torque. DO NOT OVERTIGHTEN. 7. Insert the replacement high-limit wires into the connector, ensuring each wire is in the correct hole.. Pin Pusher P/N Reconnect the high-limit wire-harness connector. 9. Install and secure the back cover(s). 0. Return fryer to operation. Place wrench here when removing and installing high-limit. -9

15 CHAPTER : SERVICE PROCEDURES.8 Replace Frypot. Perform Procedure., Replace Temperature Probe, Steps -7.. Perform Procedure., Replace Computer/Controller, Steps -.. Perform Procedure.7, Replace High-Limit, Steps -.. Disconnect the element wire harnesses.. Remove the screws securing the capping piece from the fryer. Remove the capping piece and set aside.. If the fryer has a built-in filtration system, remove all the plumbing from the frypot, including oil-return and drain plumbing. 7. Remove the screws securing the frypot to the front frame of the fryer. 8. Carefully lift the frypot from the cabinet. 9. Remove the drain valve from the old frypot and install on the new frypot. 0. Apply Loc-Tite Sealant PST 7 to the high-limit threads. Install high-limit into the new frypot.. Disconnect the tilt plate springs from the old frypot.. Remove the securing screws from the tilt plate. Lift the tilt plate/heating element assembly from the old frypot and install on the new frypot.. Follow the preceding steps in reverse to install the new frypot into the fryer.. NOTE: Apply Loc-Tite Sealant PST 7 to all pipefittings prior to installation. -0

16 CHAPTER : SERVICE PROCEDURES.9 Replace Contactor (Latching or Heating). Perform Procedure., Replace Computer/Controller, Steps -.. Identify faulty contactor. Remove all wiring connected to the contactor terminals (circles) inside the component box. Tape wire-pairs together and mark each wire-set or wire for reassembly.. Remove contactor-mounting screws (arrow) and remove the contactor.. Install the new contactor and connect the wiring removed in Step. Remove contactor-mounting screws after removing all wiring from the contactor (circles)..0 Built-in Filter System Service Procedures Troubleshooting Built-In Filtration Systems One of the most common errors is placing the filter paper on the bottom of the filter pan rather than over the filter screen. CAUTION Ensure that the paper support screen is in place prior to filter paper placement and filter pump operation. Improper screen placement is the major cause of filter system malfunction. Whenever the complaint is "the pump is running, but no oil is being filtered", check the installation of the filter paper, and ensure that the correct size is being used. While you are checking the filter paper, verify that the O-rings on the supply line connection are present and in good condition. Missing or worn O-rings allow the pump to take in air, decreasing its efficiency. In addition, oil leaks into the fryer and on the floor each time a frypot is filtered. -

17 CHAPTER : SERVICE PROCEDURES.0 Built-in Filter System Service Procedures (cont.) If the pump motor overheats, a circuit breaker will trip and the motor will not start until the breaker is reset. If the pump motor does not start, press the white reset button located under the component box, inside the cabinet. If the pump starts after resetting the breaker, then something is causing the motor to overheat. A major cause of overheating is when several frypots are filtered sequentially, thus overheating the pump and motor. Allow the pump motor to cool at least 0 minutes before resuming operation, and allow time for the motor to cool between sequential frypot filtering. Pump overheating can be caused by: Solidified shortening in the pan or filter lines, or Attempting to filter unheated oil or shortening. Cold oil and shortening are more viscous, causing the pump motor to load up and overheat. Always filter with the oil or shortening at operating temperature [~0 F (77 C)]. If the motor runs but the pump does not, there is a blockage in the pump. Incorrectly sized or installed paper/pads will allow food particles and sediment to pass through the filter pan and into the pump. When sediment enters the pump, the gears bind, causing the motor to overload, again tripping the thermal overload. Shortening that has solidified in the pump will also cause it to seize, with the same result. A pump seized by debris or hard shortening must be disassembled, cleaned, and then reassembled before continuing use. Use the following procedure:. Disconnect power to the filter system.. Remove the front cover of the pump to access the gears inside (see illustration below- 8-GPM pump shown), if the pump is accessible while still inside the cabinet. Remove bolts to remove pump cover. Remove debris or hardened shortening to free gears. -

18 CHAPTER : SERVICE PROCEDURES.0 Built-in Filter System Service Procedures (cont.). If the front cover is not accessible, the pump must be removed from the pump motor (remove input/output plumbing from the pump prior to removing pump). Remove three setscrews from the pump-shaft housing to disengage the pump from the motor. Remove the gears and thoroughly clean all internal components. Ensure the inside of the pump housing is free of any debris or hardened shortening before reassembling. Failure to completely clean the inside housing and ring gear will cause gear binding after reassembly. Filter paper/pads that are the wrong size or installed incorrectly will also allow food particles and sediment to pass through and clog the suction tube in the bottom of the filter pan. Particles large enough to block the suction tube may indicate that the crumb tray is not being used.. Basket Lift Service Procedures Ultimate Electric Series fryers may optionally be equipped with automatic basket lifts to ensure uniform cooking times. Electric fryers can be equipped with "modular" or "bell-crank" basket lifts. A modular basket lift (illustrated) consists of a toothed rod to which the basket lift arm is attached, a reversible-drive gear motor and a pair of roller-activated microswitches. The gear motor engages the teeth in the rod, moving it up or down, depending upon the direction of rotation of the motor. Microswitches at the upper and lower limits of movement stop the motor when the basket is in the full up or full down position. Timing circuitry in the controller initiates and stops basket lift operation depending upon the variables programmed by the operator. When the product button is pressed, or the manual control is activated, the timing circuitry activates a coil in the basket lift relay to supply power to the lower microswitch. The microswitches stop the motor at the lift s upper and lower travel limits and reverse the direction of current flow thus reversing the motor direction. Modular Basket Lift Assembly (Typical). -

19 CHAPTER : SERVICE PROCEDURES. Basket Lift Service Procedures (cont.) Simplified Schematic H N Normally Open Upper-limit Microswitch M or Basket Lift Relay Normally Closed Lower-limit Microswitch To computer/controller via interface board When the product button is pushed on the computer/controller, current flows through a coil in the basket lift relay, causing the lower circuit to be activated. The basket lift lowers, closing the normally open upper-microswitch. When the lower normally closed microswitch is opened by the downward moving lift rod, power to the motor ceases to flow. When the computer/controller timesout, the current to the relay coil is interrupted, allowing the upper circuit to be activated. The basket lift then raises and closes the lower microswitch. When the basket lift rod clears the upper microswitch, the microswitch opens, and power to the circuit is interrupted, stopping the motor. Pushing the product button or activating the manual control (if equipped) restarts the cycle. Problems with the modular basket lift design can be grouped into three categories: Binding/jamming problems Motor and gear problems Electronics problems -

20 CHAPTER : SERVICE PROCEDURES. Basket Lift Service Procedures (cont.) BINDING/JAMMING PROBLEMS Noisy, jerky or erratic movement of the lifts is usually due to lack of lubrication of the rods and their bushings. Apply a light coat of Lubriplate or similar lightweight white grease to the rod and bushings to correct the problem. With the modular basket lift, another possible cause of binding is improper positioning of the motor, which prevents the gear from correctly engaging the teeth in the rod. To correct the problem, loosen the screws that hold the motor in place and move it forward or backward until the rod has just enough slack to be rotated slightly. MOTOR AND GEAR PROBLEMS With the modular basket lift, the most likely problem to be encountered in this category is erratic motion of the lift due to a worn drive gear. Failure to keep the lift rod and bushings properly lubricated will cause unnecessary wear of the gear. The problem is corrected by replacing the worn gear. If the lift cycles correctly but fails to remain in the up position (i.e., goes up, but then slowly settles back down into the frypot), the problem is a failed motor brake. The motor must be replaced. If power is reaching the motor but the motor fails to run, the motor is burned out and must be replaced. ELECTRONICS PROBLEMS Within this category are problems associated with the relays, microswitches, capacitors, resistors, interface board, wiring, and controls. The most common problem in this category is a lift that continuously travels up and down. This is usually caused by a microswitch that is out of adjustment. Troubleshooting the electronics of a modular-type basket lift is simply a process of verifying current flow through the individual components up to and including the motor. Using a multimeter set to the 0 VAC range, check the connections on both sides of the component for the presence of the applied line voltage. The accompanying simplified wiring diagrams identify the components and wiring connection points. -

21 CHAPTER : SERVICE PROCEDURES. Basket Lift Service Procedures (cont.) Ultimate Electric Series fryers, used to cook large amounts of bone-in chicken in a single drop, are equipped with bell-crank style basket lifts. Two components, a cam and bell crank, are connected to the basket lift arm by a flat metal link. The cam is attached to a drive motor. The motor rotates the cam, thus raising or lowering the lift arm linked to the bell crank. A rolleractivated microswitch is used to limit travel. When the roller in the microswitch is in contact with the cam, the motor is energized. As the cam rotates, the roller loses contact with the cam and the motor power circuit is broken, de-energizing the motor. Bell-crank style basket lift. Timing circuitry in the controller initiates and stops basket lift operation. When the product button is pressed, the timing circuitry activates a coil in the basket lift relay to supply power to the motor. The microswitch stops the motor at the lift s lower travel limit and the switch contacts are reversed. At the end of the programmed cooking time, the timing circuit activates the coil once more and the lift rises until the microswitch again loses contact with the cam, opening the motor power circuit and stopping the motor. A typical bell-crank wiring diagram is shown below. REFERENCES TO LEFT & RIGHT ARE FROM REAR OF FRYER M WHT M LH SIDE RH SIDE BLK COM ALL RELAYS VDC COIL WHT COM N.O. N.C. NC NO NC NO N.O. N.C. COM COM RED NC NO NC NO PUR BLU ORG FUSE AMP B.L.COM LINE COM LINE LOAD B.L. LH B.L. COM GRD B.L. RH -

22 CHAPTER : SERVICE PROCEDURES. Electric Interface Board Diagnostic Chart The following diagram and charts provide ten quick system checks that can be performed using only a multimeter. Note: The sealed relays are not replaceable. If a relay fails, the interface board must be replaced K K K K Diagnostic LED Legend CMP indicates power from V transformer indicates power from V transformer HI (RH) indicates output (closed) from right latch relay HI (LH) not applicable to Ultimate Electric fryers HT (RH) indicates output from right heat relay HT (LH) not applicable to Ultimate Electric fryers AL (RH) indicates output (open) from right latch relay AL (LH) not applicable to Ultimate Electric fryers Meter Setting Test Pin Pin Results VAC Power 0 VAC Scale of J of J - VAC VAC Power 0 VAC Scale of J Chassis -0 VAC *Probe Resistance R X 000 OHMS of J of J See Chart Hi-Limit Continuity R X OHMS 7 of J of J 0 - OHMS Latch Contactor Coil R X OHMS 8 of J Chassis -0 OHMS Heat Contactor Coil R X OHMS 9 of J Chassis 8- OHMS *Disconnect -Pin harness from the computer/controller before testing the probe circuit. -7

23 CHAPTER : SERVICE PROCEDURES. Probe Resistance Chart Use the chart below when testing temperature probes and probe circuits for proper operation. Probe Resistance Chart F OHMS C F OHMS C F OHMS C F OHMS C F OHMS C Element Wattage/Amperage Calculation Charts Use the charts below when changing voltages or determining amperage for a given element configuration. L Three Phase Amperage L L To determine Three Phase Amperage, solve for Single Phase first: Wattage Voltage = Single Phase Amps Then divide the Single Phase Amperage by.7 to determine Three Phase Amperage. Example: 7,000W 0V = 70.8 Amps.7 = 0.9 Amps per Phase L Three Phase Wattage L L To compute the New Wattage Rating of an element if a different voltage is applied, use the following formula: New [ Old Voltage] X kw Listed = New Wattage Rating Example: If 08V supply is applied to a 7 kw element rated for 0V, the calculation is as follows: 08V [ 0V ] =.77 kw X 7,000 Watts -8

24 CHAPTER : SERVICE PROCEDURES. Wiring Diagrams, Main.. Wiring Diagram, Main- 08/0V: 7, 8E and 8UE -9

25 CHAPTER : SERVICE PROCEDURES.. Wiring Diagram, FAST: 7, 8E and 8UE -0

26 CHAPTER : SERVICE PROCEDURES.. Wiring Diagram, Main- KSCFH8E FAST Export (India) -

27 CHAPTER : SERVICE PROCEDURES.. Wiring Diagram, Main- 80V: 8UE and EH7 WHT 70C WHT C BLK C RED 7C PUR 7C BRN 0C BLU H BLU H BLU H BLK H BLK H BLK H RED 0C RED 8C* RED C RED 9C* GRN/YEL 7C WHT C BLK 7C WHT C BLK C BLU 8C BLU 9C 0V V YEL C ORG C ORG C YEL 7C L R LATCH CONTACTOR BRN 0C K K HEAT CONTACTOR BRN 0C 0V 80V DRAIN SWITCH BLK 8C 9 9 J FRY CM. COMPUTER (NO. 8078) TO INTERFACE BOARD 800D FUSE BLK C 0V V FUSE T T BLK C C TILT SWITCH PROBE WHT C HIGH LIMIT THERMOSTAT NC WHT BLK BLU 0C BLU C RED RED WHT To Basket Lift RED C WHT C BLU 7C RED C RED C BLU C J GND 80V ELEMENTS * Non Basket Lift Position COMPUTER INTERFACE BOARD (NO. 8079) TO FRY BM. COMPUTER GROUND TERMINAL WIRE PHASE, L, L, L TERMINAL BLOCK -

28 CHAPTER : SERVICE PROCEDURES.. Wiring Diagram, Main- 08V- 8UE and EH7 WHT 70C WHT C BLK C RED 7C PUR 7C BRN 0C BLU H BLU H BLU H BLK H BLK H BLK H GRN/YEL 7C WHT C BLK 7C WHT C BLK C BLU 8C BLU 9C RED C WHT C BLU 7C RED C RED C BLU C 08V V YEL C ORG C ORG C YEL 7C L R LATCH CONTACTOR BRN 0C K K HEAT CONTACTOR BRN 0C DRAIN SWITCH BLK 8C 9 9 J FRY CM. COMPUTER (NO. 8078) TO INTERFACE BOARD 80A FUSE BLK C 08V V FUSE T T BLK C C TILT SWITCH PROBE WHT C HIGH LIMIT THERMOSTAT NC WHT BLK BLU 0C BLU C RED RED WHT To Basket Lift BLU 8C J GND 08V ELEMENTS COMPUTER INTERFACE BOARD (NO. 8079) TO FRY BM. COMPUTER GROUND TERMINAL WIRE PHASE,, L L L L TERMINAL BLOCK WIRE PHASE, L, L, L TERMINAL BLOCK -

29 CHAPTER : SERVICE PROCEDURES.. Wiring Diagram, Main- KSCFH8E 7C 809B C NOTE: RIGHT FUSE HOLDER AND WIRE C ARE ELIMINATED LATCH CYCLING WIRE 7C GOES FROM LATCH CONTACTOR CONTACTOR CONTACTOR TO T. C C C T T C C C INTERFACE BOARD 0C C BLK C WHT TO FILTER BLK RED TILT SWITCH WHT HIGH LIMIT OIL TEMPERATURE SENSOR ON ELEMENT HEATING ELEMENT C COMPUTER (BACK) C C C C C C C C C C C C FUSE BLOCKS 0A FUSE EACH L L TERMINAL L L L BLOCK PHASE, WIRE DELTA GROUND 7C TO T TERMINAL BLOCK HEATING ELEMENT C C C C C C C C C C C C C C C L L L 77C CYCLING CONTACTOR 7C C C LATCH CONTACTOR C L L L C C V COM TRANSF 08V 0V CABLE TO REAR L L L L 0C C 8C 8C 7C 9C C C C C C C C C C 7C 8C 9C C C COM C DRAIN SWITCH V TRANSF 7C SPEAKER 8C BLK KSCFH8 WIRE WYE CONNECTION N L L L GROUND C C C C RED C 7C C C C C FLOAT SWITCH CABLE TO REAR 7C PIN CABLE C 8C BLK AMP PINS 7C WHT FUSE HOLDER 7 BLK BLK MALE AMP PINS FEMALE FUSE HOLDER -

30 CHAPTER : SERVICE PROCEDURES..7 Wiring Diagram, Main- BIH7 0A FUSE 0C WHT 0C BLK YEL 0C BRN C BRN DRAIN NC SWITCH COM 8C BLK NO FUSES USED ONLY FOR WIRE, PHASE 0A C WHT FUSE WIRE, PHASE, L, L, L TERMINAL BLOCK N L C WHT C WHT C BLK WHT BLK T T C BLK 9C WHT HIGH LIMIT THERMOSTAT BLK 0C BLK 0C C BY-PASS BLK C SWITCH BLK BLK C RELAY NC NO COM V TILT SWITCH HEAT TAPE - WATT 0C RED RED BOMB TAIL NC 8C BLK 9C WHT 0V V BLK WHT 0C BLU C BLU RED RED WHT YEL C 0V V C RED C WHT 7C BLU C RED C RED C BLU 08V OR 0V ELEMENTS R L 7C BLU LATCH K K HEAT CONTACTOR CONTACTOR C ORG C ORG H BLU H BLU H BLU H BLU H BLU H BLU J GND COMPUTER INTERFACE BOARD (NO ) GROUND TERMINAL WIRE PHASE,, L L TERMINAL BLOCK 0V ONLY L AMP FUSE WHT C WHT C WHT C BLK C CIRCUIT CB BREAKER RED C PROBE V NC OIL RETURN RED 80C 8C COM MICRO SWITCH YEL SHOWN IN OFF HIGH VOLTAGE SHOWN LOW VOLTAGE SHOWN NO WHT T T8 POSITION T T T8 T T T MOTOR T T P P BLK P P FOR CHANGE OF ROTATION INTERCHANGE LEADS T AND T8 BOMB ON THE MOTOR 00C WHT TAIL WHT 80B

31 CHAPTER : SERVICE PROCEDURES. Wiring Diagrams, Basket Lifts.. Modular Basket Lifts LEFT SIDE M RIGHT SIDE M RESISTORS**. µf **0V UNITS: TWO OHM **08-0V UNITS: FOUR 0 OHM. µf COM NC NO UPPER SWITCH NC COM NO NC COM NO COM NC NO COM NO NC COM NO NC UPPER SWITCH LOWER SWITCH LIN COM LINE LOAD B.L. LH B.L. COM GND B.L. RH LOWER SWITCH LEFT SIDE M RIGHT SIDE M 0V Basket Lifts Only- Three Sets of Resistors Ohm Ohm 0 Ohm -

32 CHAPTER : SERVICE PROCEDURES.. Bell-Crank Style Basket Lifts REFERENCES TO LEFT & RIGHT ARE FROM REAR OF FRYER M WHT M LH SIDE RH SIDE BLK COM ALL RELAYS VDC COIL WHT COM N.O. N.C. NC NO NC NO N.O. N.C. COM COM RED NC NO NC NO PUR BLU ORG FUSE AMP B.L.COM LINE COM LINE LOAD B.L. LH B.L. COM GRD B.L. RH -7

33 CHAPTER : SERVICE PROCEDURES.7 Wiring Diagrams: Built-in Filtration.7. Wiring Diagram, 80V Systems With Built-in Filtration BLK # WHT C P WHT# BLK C BLK C LOW VOLTAGE SHOWN T8 T T T T J BOX (DOUBLE) FUSE AMP JUCTION BOX COVER PLATE FUSE FUSE HOLDER GRN HEAT TAPE - WATT (TRIPLE) YEL 8C RED 80C YEL 8C RED 8C YEL 8C RED 8C INPUT V CIRCUIT WHT C BLK C CB CIRCUIT BREAKER 7 AMP-0V AMP-80V HIGH VOLTAGE SHOWN WHT# T T T8 T T BLK P SCF OIL RETURN TRANSFORMER/RELAY ASSY BLK 0C NC RELAY NO 0V COM V V RED C MOTOR P NC NC P COM COM FOR CHANGE OF ROTATION INTERCHANGE LEADS T AND T8 ON THE MOTOR NO OIL RETURN LH FRYER NO OIL RETURN CENTER FRYER MICROSWITCH SHOWN IN OFF POSITION NC COM NO OIL RETURN RH FRYER 800F -8

34 CHAPTER : SERVICE PROCEDURES.7. Wiring Diagram, 08V Systems With Built-in Filtration WHT C WHT C P BLK 0C BLK C BLK C HIGH VOLTAGE SHOWN T T T NC NC (DOUBLE) (TRIPLE) YEL 8C RED 80C YEL 8C RED 8C YEL 8C RED 8C INPUT 08V CIRCUIT BLK C WHT# BLK CB WHT C LOW VOLTAGE SHOWN T T T8 T T P BLK 0C SCF OIL RETURN TRANSFORMER/RELAY ASSY BY-PASS SWITCH 08V RELAY PN 9 NC NO COM V V RED C T8 T MOTOR COM COM P P FOR CHANGE OF ROTATION INTERCHANGE LEADS T AND T8 ON THE MOTOR NO OIL RETURN LH FRYER NO OIL RETURN CENTER FRYER MICRO SWITCH SHOWN IN OFF POSITION NC COM NO OIL RETURN RH FRYER 80A -9

35 CHAPTER : SERVICE PROCEDURES.7. Wiring Diagram, /0V KFC Systems With Built-in Filtration 80B V OUT TO RH FRYER CIRCUIT BLU BLK V 0V CIRCUIT BREAKER V - 7 AMP 0 V - AMP YEL YEL YEL V ORG YEL LH FRYER RH FRYER NC NO COM PUR RED YEL # NC BLK NO ORG COM V V YEL YEL # PUR ORG WHT YEL MANUAL BY PASS SWITCH CB BLK BLK KSCFH8E FILTER CIRCUIT BLK WHT INPUT V/0V FILTER CIRCUIT PUR ORG WHT YEL T T T8 T MOTOR T T FOR CHANGE OF ROTATION INTERCHANGE LEADS T AND T8 ON THE MOTOR RED NC COM NO NC COM WHT# BLK NO OIL RETURN MICRO SWITCH RH FRYER TRANFORMER VAC OR 0 VAC TO VAC OIL RETURN MICROSWITCH -0

36 CHAPTER : PARTS LIST. Accessories 7 Item Part Number Description Basket Hanger * 0-98 Cover, Vat- All Ultimate Electrics Thumbscrew, Basket Hanger 0-88 Joiner Strip Brush, Frypot * 80-0 Grid, Frypot W/Standoff * Grid, Frypot- FPH7 Systems Fry Basket, Twin Basket * Fry Basket, Full Basket 8-7 Caster, "- W/O Brake (Mounting Hardware Included) Caster, "- With Brake (Mounting Hardware Included) * Fryer s Friend (Clean-out Rod) * Not Illustrated -

37 CHAPTER : PARTS LIST. Basket Lift Assembly (Modular) and Related Components 0V Basket Lifts Only 08-0V Basket Lifts Only Item Part Number Description 00- Mount, Basket Lift Assembly 80-9 Motor Assembly- All EH7 Basket Lifts 0-770SP Resistor Assembly, 00/08/0V * 0-77SP Resistor Assembly, 0/0/0V 80-80SP Resistor Assembly, 0V (Used On 80V Fryers) * 807- Resistor, Ohm-0V (For 80V Fryers) * Resistor, 0 Ohm- 00V/0V (For 08/0V and 0/0 Fryers) * 807- Resistor, Ohm- 0V/0V (For 0/0V Fryers) * Not Illustrated -

38 CHAPTER : PARTS LIST. Basket Lift Assembly (Modular) and Related Components (cont.) Item Part Number Description Connector, -Pin 807- Capacitor, 0V Basket Lifts * 807- Capacitor, 08V Basket Lifts Microswitch Ring, Truarc Screw, Washer, Lock # Nut, Nut, 8-, Hex Keps Screw, -0 x ¾" * Screw, -0 x ¼" (Use with 08V Basket Lifts) Screw, (Drill #8) Screw #0-/ Hex Screw, Hex 8- x ½" 80-0 Basket Lift Rod Insulation, Switch Box Bushing, Bronze.0 ID Gusset Chassis, Left Chassis, Right Relay, VDC * 00- Enclosure, Basket Lift Assembly * 00- Mount, Conduit- Basket Lift Wire Harness Cover * 00- Cover, Basket Lift Wire Harness * Not Illustrated -

39 CHAPTER : PARTS LIST. Basket Lift Assembly (Modular) and Related Components (cont.) Item Part Number Description 0-9SP Roller Assembly, Bracket Bolt, ¼-0 x -¼" Hex Head S/S Washer, Flat- ¼" S/S Spacer, Tubular Basket Lift Roller Roller, Basket Lift Nut, Cap- ¼-0 S/S Screw, ¼-0 x ¾" Round Slotted S/S Basket Lift Arm- Left Basket Lift Arm- Right -

40 CHAPTER : PARTS LIST. Cabinetry and Related Components.. EH7 & 8UE

41 CHAPTER : PARTS LIST.. EH7 & 8UE (cont.) Item Part Number Description 0-7SP Cover Assembly, Dump Station Front 00- Guard, Rear Wire- Top 00- Guard, Rear Right Center Wire, Side 00- Channel, Bus Electric 00-8 Channel, Vessel- Outer Back Panel 00-8 Channel, Vessel- Outer Back Panel Shield, Burner- Heat Bracket, Lower Hinge Post, Door Channel, Front & Rear- Single and -Battery With Dump Station * 00- Channel, Front & Rear- -Battery With Dump Station 00- Channel, Base 00- Frame, Base- 7 Systems * 00-9 Frame, Base- BIH7 00- Base, Cabinet Lower Frame- 7 Systems * 00-9 Base, Cabinet Lower Frame- BIH7 00- Guard, Center Rear Wire 00-8 Cover, Structural Back- Lower 0- Panel, Inner-Left Side 7 0- Side, Cabinet- Left (With Hole) 8 0- Gusset, Side Panel- Left 9 0- Panel, Inner- Right Side 0 0- Side, Cabinet- Right (With Hole) 0- Gusset, Side Panel- Right 0-7 Duct, Door Access 0-88 Bracket, Cabinet Batter - Side, Cabinet- Left Side - Side, Cabinet- Right Side 8-8 Support, Leg Wireway, Control Panel * Not Illustrated -

42 CHAPTER : PARTS LIST.. EH7 & 8UE (cont.) Item Part Number Description Channel, Leg Support Slide, Filter Pan Support Bottom, Bus Channel 8-88 Cover, Bus Channel (With Bracket) 0-08SP 00-8 Panel, Door- Inner 00-0 Door Pin 0-7 Panel, Door- Outer Handle, Door Door Assembly (Door Pin Not Included) See Section.. For Additional Door Components * Screw, 0- x ½" Slotted Head (Use With 80-0) * Washer, ¼ Spring-Lock (Use With 80-0) Magnet, Door Back, Upper Cabinet Cover, Vent- Cabinet Back * Not Illustrated -7

43 CHAPTER : PARTS LIST.. KFC8E Electric

44 CHAPTER : PARTS LIST.. KFC8E Electric (cont.) Item Part # Description 0-99 Side Panel, Painted, LH ( use -78 for India) 0-99 Side Panel, Painted, RH (use -78 for India) Caster, Stationary- " Rigid 80-0 Leg Support, Channel- Leg/Caster 0-8 Gussets, L/H (use -78 for India) Gussets, R/H use -78 for India) Lower Hinge Bracket (Door) Door Panel, Inner (use 0-80 for India) 0 0-7SP Door Panel, Outer use 0-98 for India) * 0-08SP Door Assembly (Door Pin Not Included) (use 0-9 for India See Section.. For Additional Door Components 80-0 Magnetic Door Catch Handle, Door use for India) * Screw, 0- x ½" Slotted Head (Use With 80-0) * Washer, ¼ Spring-Lock (Use With 80-0) 00-0 Door Pin 0- Top Cap use 8-7 for India 8E)(use 0- for 8E Injdia) 0-80 Slide, UFF Filter Pan- Front (Long) (use 0-78 for India) 0-8 Slide, UFF Filter Pan- Rear (Short) (use 0-78 for India) Shield, Heat Base, Lower Frame Channel, Base Plate, Mounting (UFF) 00- Base, Upper 00- Channel, Bus 00-7 Cover, Access Duct 0- Panel, Inner- Right Side 0- Panel, Inner- Left Side Post, Door Guard, Wire- Center Guard, Wire- Top Guard, Wire- Right Side Center Back, Cabinet * 00- Closure, Lower Structural Back (Single Fryers) * Not Illustrated -9

45 CHAPTER : PARTS LIST.. KFC8E Electric (cont.) Item Part # Description 00-8 Cover, Back Vent * Screw, Hex Slotted Head With Washer- #8 x /8" 8- Housing, Tilt (use with studs for India 8E) (use 8-80 for 8E India) 0-88 Joiner Strip (use with slots for hooks for India) Hanger, Basket (use 0-78 with keyholes for India 8E) (use for 8E India) Thumbscrew, ¼ x -/8" Nickel-Plated * Not Illustrated.. Door Components Spring-Loaded Door Pins Item Part # Description 8- Panel, Door- Outer (Current Production UE Only) 00-0 Liner, Door (Current Production UE Only) Handle, Door (See Section.. and.. for connecting hardware) 80-0 Magnet, Door (Offset) 0-0SP Pin, Door Slotted (With Keeper) Spring, Door Hinge * Not Illustrated -0

46 CHAPTER : PARTS LIST.. Top Cap and Tilt Housing Components Item Part Number Description 0-7SP Tilt Housing (With Nutsert), -Battery EH7 W/Dump Station 0-7SP Tilt Housing - EH7 W/Dump Station 8- Tilt Housing, -Battery EH Tilt Housing, -Battery EH7 W/Dump Station 8-8 Tilt Housing, BIH/EH7- Single 8-09 Top Cap, -Battery EH Top Cap, -Battery EH Dump Station, EH7 * 8- Strainer (Screen), Dump Station Drain Grid, Dump Station 0 0-7SP Cover Assy, Dump Station- Front * Not Illustrated -

47 CHAPTER : PARTS LIST. Computers, Controllers and Related Components CM-S 7 8 -

48 CHAPTER : PARTS LIST. Computers, Controllers and Related Components (cont.) Item Part Number Description All Computers/Controllers Come With Bezels Except Item # 0-87 Computer, CM-III Full-Vat 0-0 Controller, Digital- Full-Vat * 0-0 Controller, Digital- Full-Vat- CE 0-00 Computer, KFC- Electric (Non-CE) * 0-00 Computer, KFC- Electric (CE) 0-08 Computer, CM-S (Segmented Programming) 80-7 Controller, Analog- Solid State ( On, Off) 0- Control Panel- All Ultimate Electrics 7 8- Bezel, Computer- All Except KFC8E * 8-88 Bezel, Computer- KFC8E Only 8 Electronic Thermostat Controller 0-98 Faceplate, Potentiometer Assembly- 8UE 80-0 Label, Faceplate- Electronic Thermostat Controller * Not Illustrated 0-080SP 8-0 Pot Assy, Electronic Thermostat Controller- 8UE Knob, Pot Assy- Electronic Thermostat Controller- 8UE -

49 PUMP OFF ULTIMATE ELECTRIC SERIES FRYERS CHAPTER : PARTS LIST. Contactor/Wireway Box and Related Components

50 CHAPTER : PARTS LIST. Contactor/Wireway Box and Related Components (cont.) Item Part Number Description 80- Interface Board- (All Except Electronic Thermostat Controller) Interface Board- (Electronic Thermostat Controllers Only) Transformer, 0V, 0/0 Hz V 0VA (80V Units) * Transformer, 08-0V, 0/0Hz V 0VA Transformer, 0V 0/0 Hz V 0VA (80V Units) * Transformer, 08-0V, 0/0Hz V 0VA * Transformer, 08-0V 0/0Hz V 0VA 807- Relay, VAC Contactor, Mercury- 0VAC 0-Amp (7 kw Units) * Contactor, Mercury- 0VAC 0-Amp ( kw Units) * Contactor, Mechanical 0VAC -Amp Contactor, Latching- 0-Amp, -Pole Fuse Holder, Buss Fuse * Fuse, 0-Amp Sound Device- All Except KFC8E Speaker, Sound- KFC8E Only Breaker, Circuit- Amp (0V Filter Circuit) * Breaker, Circuit- 7 Amp (0V Filter Circuit) Switch, Toggle- Filter Bypass- ON-OFF Fuse Block, Buss #98, -Pole 807- Power Block -Phase- WYE Only * Power Block -Phase- DELTA Only 8-8 Wireway Control Panel (Box)- All Ultimate Electrics * Cover, Wireway Control Box (Clear Lexan) * Transformer, 80V-0VA (With Basket Lift) * Transformer, 80V-0VA (Without Basket Lift) * Transformer, 0V 0/0 Hz -V 0VA (UFF 00 Pump Motor Relay) * Transformer, 08V, 0/0Hz V 0VA (UFF 00 Pump Motor Relay) * 8-09 Cover, 80V Transformer- Left Side * 00-9 Cover, Terminal Block- All Except Electronic Thermostat Controller * Cover, Terminal Block- Electronic Thermostat Controller Only * Not Illustrated -

51 CHAPTER : PARTS LIST. Filter Pan and Related Components- Built-in Filtration.. Under Fryer Filter (UFF) UFF 80 (00 Lb Capacity) Item Part Number Description 0-8SP Filter Pan, UFF 80 (00 Pound Capacity) 8- Support Grid (Bottom Pan Screen) Filter Paper, x " (00 Sheets) 8-9 Hold-down Ring, Weighted 8- Crumb Basket 0-87SP Filter Pan Cover, Front SP Filter Pan Cover, Back Bolt, ¼-0 x ½" Steel Insert, Caster Nut, Oval Locking- ¼ Screw, ¼-0 x ½" Caster, " -

52 CHAPTER : PARTS LIST.. Under Fryer Filter (UFF) KFC8E Only

53 CHAPTER : PARTS LIST.. Under Fryer Filter (UFF) KFC8E Only (cont.) Item Part Number Description 8-0 Pan, Filter- KFC8E 80-9 Grid, Filter- KFC8E Paper, Filter- -½ x -¾" (00 Sheets) 8-0 Ring, Hold-Down (No Handles)- KFC8E * 8-0 Handle, Hold-Down Ring- KFC8E 8-0 Crumb Basket- KFC8E 0-090SP Lid, Filter Pan- Front SP Lid, Filter Pan- Back Screw, SS- ¼-0 x ½" Phillips Head Insert, Mounting Plate- Caster Caster, " Nut, Nylock- ¼ Bolt, ¼-0 x ½" Hex Head Plug, SS- /8 Square Head Motor, Filter Pump- 0/0V / HP Pump, Filter- 8GPM Fitting, Oil Suction Start 8-00 Nipple, ½" NPT x Close BM Tee, ½" NPT BM 8-0 Plug, ½" NPT BM Nipple, ½ NPT x 7-¼" Elbow, ½" x Nipple, ½ NPT x -½" Union, ½" NPT BM 8-8 Tube, Suction Assembly Coupling, Full Disconnect, Male * 8-9 O-Ring, Disconnect (Qty: ) 0-080SP Drip Cup Assembly * Not Illustrated -8

54 CHAPTER : PARTS LIST.. Under Fryer Filter (UFF) KFC8E Export India Only Item Part Number Description Basket, Crumb 80-9 Ring, Hold-down 8-78 Lid 0-70SP Screen Assembly, Filter 8-7 Pan, Filter 8-08 Plug, ⅛" SS NPT, Sq-Head Caster, " Filter Pan * Nut, Nylock, ¼-0 * Not Illustrated -9

55 CHAPTER : PARTS LIST.. Under Fryer Filter (UFF) Filter-Leaf /Suction Tube Assembly Item Part Number Description 8-8 Filter Pan, UFF 80- Filter-Leaf Equipped 80-0 Filter Leaf 80-8 Fitting, Bottom- Filter Leaf 80-8 Fitting, Upper- Filter Leaf 8- Suction Tube Assembly- Filter Leaf * Plug, /8 Square S/S (Suction Port) 8- Crumb Basket 7 0-9SP Filter Pan Cover, Front 8 0-9SP Filter Pan Cover, Back Bolt, ¼-0 x ½" Steel Insert, Caster Nut, Oval Locking- ¼ Screw, ¼-0 x ½" Caster, " * Not Illustrated -0

56 CHAPTER : PARTS LIST.. Single Under Fryer Filter (SUFF) BIH7 and 8UE Item Part Number Description 0-SP Filter Pan, SUFF 0 BIH7 and 8UE 80- Caster, "-Swivel Nut, Nylock ¼ Plug, /8" SS Square Head * 8-08 Plug, Hex Socket, /8" NPT 8-79 Support Grid (Bottom Pan Screen)- SUFF 0 BIH Paper, Filter- x " Hold-Down Ring, Weighted- SUFF 0 BIH Crumb Basket Filter Pan Cover, Front Filter Pan Cover, Back * Not Illustrated -

57 CHAPTER : PARTS LIST.7 Frypot and Drain Valve Components High-Limit Location Included with Drain Valve Included with Drain Valve 7 8 Item Part Number Description 8- Frypot- EH7, 8UE & 8E * 8-90 Frypot- EH7 With Oil-Level Lines 8- Handle, Drain Valve- Filter Units Only * 8-87 Handle, Drain Valve- Single Fryers Only * 8-07 Cap, Drain Valve Handle- Red 00-7 Retainer, Drain Valve Nut 8-00 Insulation, Microswitch Microswitch (Domestic and CE) 0-9 Guard, Drain Valve Microswitch Nut, -0 Keps Hex- With External Teeth 8 8- Drain Valve- -½" Full Port W/ Microswitch Bracket * Not Illustrated -

58 CHAPTER : PARTS LIST.8 Oil Drain Flush Components Item Part Number Description 8-08 Bell Reducer, -½ x ½" 8-0 Elbow, Street- ½ x ½" Adapter, Male- /8 O.D. x ½" Flexline, /8 x 9-½" 8-00 Coupling, Full- ½" NPT BM Bracket, Flush Line Support Nipple, ½" x Close NPT BM Nipple, ½ x " NPT BM Elbow, ½" 90 NPT BM Flexline, /8 x " Valve, Ball- ½" * 8-8 Handle, Oil Flush Valve * 8-09 Cap, Oil Flush Valve Handle- Blue * Heater Strip- 0V/W " L * Not Illustrated -

59 CHAPTER : PARTS LIST.9 Oil Drain Manifold Components To Dump Station To Drain Valve To Drain Valve 8 Item Part Number Description 8- Elbow, with Bracket (Drain Valve Handle) 8-8 Drain Pipe, Left Side 0- Clamp, Center- Drain Pipe 8- Drain Pipe, Right Side 8-07 Tee, -½" NPT Male x -½" Long Drain Manifold Tube Pipe Cap, -½" NPT BM Nut, Slip Joint- -½" * 8-0 O-ring (Slip-Joint Nut) Coupling, Full -½"-SS Nipple, -½" x 8" NPT BM 8-07 Elbow, -½" x 90 SS * Not Illustrated -

60 CHAPTER : PARTS LIST.0 Oil Return Manifold, Motor and Pump Components PUMP MOTOR PUMP VESSEL OUTLET (REF) SEE DETAIL B VESSEL OUTLET (REF) SEE DETAIL C VESSEL OUTLET (REF) VESSEL ASSEMBLY (REF) VESSEL ASSEMBLY (REF) VESSEL ASSEMBLY (REF) PUMP MOTOR 7 (REF) 0 BRIDGE (REF) BRIDGE (REF) SEE DETAIL A 7 DETAIL A DETAIL C DETAIL B

61 CHAPTER : PARTS LIST.0 Oil Return Manifold, Motor and Pump Components (cont.) Item Part Number Description NOTE: Oil Return Components Will Vary From System To System- The Most Common Components Are Included Below Rinse Hose/Disposal Plumbing Components 8- Handle, -Way Valve- Wand/Dispose Nut, /-8 Hex * Washer, Nylon-.0 ID,.70 OD * Washer, Flat- /" SAE Cover, Microswitch * Nut, Microswitch Cover Microswitch, Roller 8-0 Insulation, Microswitch Switchbox 900- Support, Microswitch Mount Coupling Disconnect- Male Elbow, Street- ½" 90 NPT BM Nipple, ½ x -½" NPT BM Valve, Ball- Three-Way Nipple Weld Assembly- Three-Way Valve Bracket, Mounting Base * Screw, ¼-0 x ¾" Hex Head * Nut, ¼-0 Hex S/S 80-9 Adapter, Female- /8 OD x ½" 80-9 Flexline, /8 x 7-½" Flexline, /8 x 9-½" 80-8 Adapter, Male- /8 OD x ½" Elbow, Side Outlet- ½" NPT Nipple, ½ x -½" NPT BM Elbow, ½" 90 NPT BM Valve, Ball- ½" 8-0 Elbow, ½" NPT BM Drain Flush Components- -Battery & Larger Units 80- Tubing, Flare- Oil Return- -Battery Church s * Not Illustrated -