General Information. Assembly Instructions. Point-Row Option 2004-

Transcription

1 3000-3S Used with: S General Information! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! These instructions explain how to install the Point- Row Option. The point-row option allows you to raise and lower openers on each drill section independently. These instructions apply to: A S Point Row Assembly Instructions apply for 3S-3000 drills built before December 2004, up to and including S/N S1699. These drills have a single inline hydraulic filter. Definitions Right-hand and left-hand as used in this manual are determined by facing the direction the drill will travel while in use. Assembly Instructions Manual Update Refer to the S operator s manual for detailed information on safely operating, adjusting, troubleshooting and maintaining the Point-Row Option. Refer to the parts manual for part identification M S Operator s Manual P S Parts Manual Before You Start Pages 14 and 15 are a detailed listing of parts included in the Point-Row Option package. Use this list to inventory parts received. Hydraulic Assembly Refer to Figure 1 1. Unscrew hoses from tee fittings (1) on mounting bracket. Remove and discard tee fittings Figure 1 Removing Fittings Copyright 2000 Printed 02/16/ M Rev. A

2 2 Refer to Figure 2 2. Pre-assemble fittings in block. Assemble the 3/4" elbows (2) in side ports as shown. Assemble 9/16" elbows (3) in the ports in the front of the block. Assemble 3/4" plugs (4) in side ports as shown Refer to Figure 3 Figure 2 Installing Elbows 3. Mount block (5) on mounting bracket using 3/8" x 3 3/4" bolts (6), washers and locks nuts Figure 3 Mounting Block M Rev. A 2/16/2005

3 3 Refer to Figure 4 4. Using a reducer fitting (7), assemble gauge (8) on new pressure-control valve. a. Assemble reducer fitting into top-rear port. b. Apply sealant to threads on gauge. c. Thread gauge into reducer fitting until gauge is tight and facing forward. Refer to Figure 5 5. Mount the new pressure-control valve (9) on the mounting bracket using 1/4" x 2 1/4" bolts (10), flat washers, lock washers and nuts. Place the new decals (11) under the pressure-control valves. Figure 4 Reducer Fitting Figure 5 Mounting Valve 2/16/ M Rev. A

4 4 Refer to Figure 6 6. Assemble new 21" hoses (12) to top-front ports on new pressure control valves. Using tee fittings (13), assemble new 18" hoses (14) and 86" hoses (15) to bottom ports. Using adaptor fittings (16), assemble remaining 86" hoses (17) to rear ports. 7. Route 86" hoses (15 and 17) from new pressure control valves back to drill frame. 8. Connect hoses to new block. Connect 21" hoses to lower-front ports in block. Connect 18" hoses to top-front ports in block. Connect hoses to block in same order as valves. (For example, connect hoses from center valve to center ports in block.) Figure 6 Hoses M Rev. A 2/16/2005

5 5 Refer to Figure 7 9. At the drill frame, remove the tee fittings (18) in the wing hydraulic circuit Figure 7 2/16/ M Rev. A

6 6 Refer to Figure Using two elbow fittings, connect hoses from the pressure-control valve on the far left (19) to left wing cylinders. 11. Using two more elbow fittings, connect hoses for pressure-control valve on the far right to right wing cylinders (20) Figure Using the existing tee fittings, connect hoses from the pressure control valve in the center (21) to center section cylinders. IMPORTANT: Connect hoses from rear port in the pressure-control valves to the base end of cylinders. Connect hoses from bottom port in pressure-control valves to rod end of cylinders M Rev. A 2/16/2005

7 7 Refer to Figure Connect hoses from tractor outlets to the elbow fittings (22) in the side of the block as follows. On drills with bypass valve at tractor: Connect hose from filter (23) to V1 (upper elbow). Connect the other hose (24) to V2 (lower elbow). On drills with bypass valve on drill: Connect hose from filter (23) to V1 (upper elbow). Connect hose from top rear port on bypass valve to V2 (lower elbow) Figure 9 Refer to Figure Secure hydraulic hoses under hose clamps on tongue (23) and frame (24) Figure 10 2/16/ M Rev. A

8 8 Mount Control Box Refer to Figure Mount control box (1) in a convenient location in tractor cab. Plug harness extension (2) into control box. Connect control box to a 12-volt power source such as your tractor battery. NOTE: Connect red wire to positive terminal and black wire to negative terminal. 2. Route wiring harness (3) through drill tongue. 3. Plug two-pin connectors (4) from wiring harness into coils on block. Look for letters L, C and R on leads to identify left, center and right. 4. Plug wiring-harness lead into control-box lead (5). 5. Secure wiring harness so it will not be damaged during lifting, folding, transporting or field turns. 6. If your tractor does not require a bypass valve to operate the S, discard solenoid (6) provided in point-row kit. NOTE: Contact your tractor dealer to verify if a bypass valve is needed to operate the S with your tractor. On models S1399 and beyond, if you install a bypass valve on your tractor, install solenoid (6) into front port in bypass valve. Plug twopin connector on harness extension (7) into solenoid. On drills with bypass valve at tractor: Install solenoid (6) into front port in bypass valve. Plug two-pin connector on harness extension (7) into solenoid. On drills with bypass valve on drill: Install solenoid (6) into top port on bypass valve (8).Plug two-pin connector from monitor lead(s) marked with letter "S" into solenoid. Figure M Rev. A 2/16/2005

9 9 Right-Hand Drive Refer to Figure Remove U-joint (1) from shaft by driving out roll pin. Drive out remaining roll pins and remove inner shaft (2) from drill. Discard inner shaft. 2. Remove drive chains (3). Remove drive sprocket (4) from outer shaft. Drive out remaining roll pins. Disassemble the clutch link (5) from clutch. 3. Disassemble clutch (6) from outer shaft by compressing the spring and sliding out the dowel pin. Remove and discard outer shaft (7). Save the clutch for later re-assembly onto center drive. 4. Replace the discarded shafts with the 6-foot shaft provided in the kit. As you install the new shaft, slide the new clutch provided in kit onto the shaft. Assemble new clutch on shaft in the same orientation as the old clutch. 5. Secure clutch to shaft. Re-assemble drive sprocket on shaft. Re-install roll pins. Reroute drive chains. Re-assemble clutch link. Re-install U-joint. Figure /16/ M Rev. A

10 10 Center Drive Refer to Figure Remove center drive shaft (1). a. Remove drive chains and acremeter (2). b. Fertilizer drills: Remove chain from center sprocket (3). c. Disassemble breakaway jaw (4) from shaft. d. Knock out remaining roll pins at sprockets and bearings. e. Remove shaft and sprockets from drill. Discard shaft. Figure M Rev. A 2/16/2005

11 11 Refer to Figure On grain-only drills, install a bearing and flanges (4) on the left side of the center bearing bracket. Use 5/16" carriage bolts, lock washers and nuts. Figure Refer to Figure Rework the clutch removed from the righthand drive. Disassemble the clutch adaptor (5) and plate sprocket (6). Discard the plate sprocket and the bolts that were holding the adaptor on the clutch. Re-assemble the adaptor onto the clutch using 1/4" x 2" bolts, lock washers and existing roll pins. Figure /16/ M Rev. A

12 12 Refer to Figure Assemble drive sprocket (7) and the acremeter (8) onto the new 23 11/16" shaft (9). Install the shaft by sliding it through the bearings on the left and center bearing brackets. Figure Assemble breakaway jaw (10) onto new 23 7/16" shaft (11). Loosen nuts on flanges at the right bearing bracket. Install shaft through far-right bearing. 6. Assemble reworked clutch (12) onto 23 7/16" shaft. 7. Slide clutch adaptor (13) over the end of the 23 11/16" shaft. Secure shafts by re-installing roll pins and retightening bolts on bearing flange. 8. Align breakaway jaws for proper contact. Refer to "Align Transfer Drive Shaft," under Leveling the Drill, Drill Preparation and Setup in the S operator s manual. 9. Re-install drive chains M Rev. A 2/16/2005

13 13 Refer to Figure Assemble clutch linkage. First, U-bolt the cam bracket (14) under the center bearing bracket using 3/8" U-bolts and lock nuts. Position cam bracket so the inside edge of the right ear is 3 5/32" from the edge of the center bearing bracket Refer to Figure 18 Figure Pin the shut-off cam (15) between the cambracket ears using clevis pin and cotter pin. 12. Attach the clutch link (16) to shut-off cam and clutch using 3/8" nylock jam nuts. 13. Use a 5/16" x 1 1/2" bolt and two nuts to secure link spring (17) to the clutch link. Hook other end of spring to center bearing bracket as shown. 14. U-bolt the shut-off bracket (18) to the opener frame directly below the cam bracket. Use 1/2" U-bolts, lock washers and nuts. Position the bracket between openers so the bracket will engage the cam when openers are lifted Figure 18 2/16/ M Rev. A

14 A 3S-3000 POINT ROW ACCESSORY Your kit includes: Qty. Part No. Part Description D 1/4 MARKER HYD HOSE GUARD D CLUTCH ENGAGE ARM D CLUTCH ENGAGE TAB H CLUTCH SHUTOFF LINK, 00 SERIES H SUBFRM CLUTCH BRKT,SOLID STAND D CLUTCH SHUTOFF CAM, 00 SERIES D POWER SHAFT 7/8 HEX CTR CLUTCH K 3S-3000F LH WING CLUTCH ASSY H CLUTCH SHUTOFF CAM PIVOT BRKT D SHAFT 7/8 HEX,POINT ROW-CENTER D SHAFT 7/8 HEX, POINT ROW-RH C CABLE TIE 21" LONG C HHCS 5/16-18X1 1/2GR C HHCS 3/8-16X1 GR C HHCS 3/8-16X3 3/4 GR C HHCS 3/8-16X1 1/4 GR C HHCS 1/4-20X2 GR C RHSNB 5/16-18X1 GR C HHCS 1/4-20X2 1/4 GR C NUT HEX 1/4-20 PLT C NUT HEX 5/16-18 PLT C NUT LOCK 3/8-16 PLT C NUT HEX 3/8-16 PLT C NUT HEX 1/2-13 PLT C NUT NYLOCK JAM THIN 3/ C WASHER LOCK SPRING 1/4 PLT C WASHER LOCK SPRING 5/16 PLT C WASHER FLAT 3/8 USS PLT C WASHER LOCK SPRING 3/8 PLT C WASHER LOCK SPRING 1/2 PLT C WASHER FLAT 1/4 USS PLT C PIN CLEVIS 3/4 X 1 1/ C PIN COTTER 1/8 X 1 1/4 PLT C PIN ROLL 1/4 X 1 1/2 LG PLT C U-BOLT 3/8-16 X 6 1/32 X C U-BOLT 1/2-13 X 3 1/32 X C SPRING EXT 1 1/16 ODX.120WX C PRESSURE GAUGE 3000 PSI C VALVE PRESS REDUCING W/CHECK C MANIFOLD ASY 3S-3000 POINT C BYPASS CARTRIDGE AND SOLENOID C TE 9/16MJIC 9/16MJIC 9/16MORB C EL 9/16MJIC 9/16MORB C AD 9/16MORB 9/16MJIC C EL 3/4MORB 9/16MJIC C PL 3/4MORB HOLLOW HEX C EL 9/16MJIC C HH3/8R /16FJIC C HH3/8R /16FJIC C HH3/8R /16FJIC9/16MORB90 2/16/ M Rev. A

15 A 3S-3000 POINT ROW ACCESSORY (Cont d) Your kit includes: Qty. Part No. Part Description C AD 9/16MORB 1/4FNPT C DECAL RIGHT SECTION C DECAL LEFT SECTION C DECAL CENTER SECTION C FLANGETTE 52 MST C BRG7/8HEX BR 52MM SPHRICAL C 3 SECT POINT ROW WIRE HARNESS C POINT ROW CONTROL BOX C POINT ROW EXT W/ POWER LEAD 2/16/ M Rev. A