RZR 900 spring/shock installation

Size: px
Start display at page:

Download "RZR 900 spring/shock installation"

Transcription

1 RZR 900 spring/shock installation Thank you for purchasing the Shock Therapy Dual Rate Spring Kit for your RZR 900. Your item list: 2 Front upper coil springs, 2 Front lower coil springs, 2 Rear upper springs, 2 Rear lower springs, 4 nylon spring dividers, 4 Silent cross over rings, 4 cross over ring O- rings, 8 aluminum spring adaptors (only for Fox equipped cars) and one cross over spanner wrench. You will need to get a coil spring compressor if you don t already have one.

2 Here are the set up notes for each 900 spring kit: Fox 2 seat Walker 2 seat Walker 4 seat Front: Pre load Cross over Rear: Pre load Cross over First, remove your front shocks from your car. Be careful not to lose the mounting spacers and the O-rings that are on them. Place one shock in a vice, upside down so both of your hands are free. Loosen the pre load nut holding tension on the top of the coil springs. On a Fox this is two, rings jammed together. Walker shocks use a single aluminum ring. You will need to spin or thread these rings to the top of the shock to loosen the coil springs as much as possible. Now slide the bump stop down the shock shaft about two inches. If the spring is loose enough you can pull the bottom spring retainer down and slide it off the shock. If the spring is still too tight you will have to use a spring compressor to compress the spring enough to remove the spring retainer. With the retainer removed you can now remove the factory spring. Now, measure where the round threaded shock body ends and the

3 head of the shock starts, down to the FRONT cross over location listed on the first page and make a mark on the shock body. For instance, if you have a Fox equipped 2 seat RZR you will make a mark at 3.5. Our Fox kits utilize a spring adaptor to convert the stock Fox preload nut and retainer to 2.5 OD allowing it to accept the correct spring. You MUST install the top adaptor ring FIRST before installing the crossover. If you have a Walker equipped car you don t need any spring adaptors. Next, install the cross over ring with the round recess groove (Oring retainer) facing the bottom of the shock right at the mark. Use the supplied spanner wrench to tighten the outer ring locking the cross over ring in place (Fox only). Now, you can install the springs as marked in your kit with the front, upper spring first, then the nylon spring divider with the long side facing the bottom of the shock (away from the cross over ring) then the front lower spring. Make sure the ends of the springs touch the plastic spring divider on opposite sides of the divider. Another way to put this is that the springs end 180 degrees apart from each other on the divider. This will be important later. Using your spring compressor, compress the springs enough to install the lower spring perch with another spring adaptor ring (Fox only) between the coil spring and the spring perch. Again, the Walker equipped car does not use the adaptor rings. With the perch in place you can move the bump stop to hold the perch in place. Now let the tension off the springs. Last, thread the pre-load rings/collar toward the springs tightening the system. Move them down to the pre-load measurement listed on the first page. This measurement is from the same place at the top of the shock down to the top of the upper spring or the bottom of the spring adaptor ring. You can now install the front shocks on your car. Move the rear of the car and remove the rear shocks. With one in a vice, loosen the pre-load collar and remove the springs. You may need the spring compressor for this. Measure from the top where the threaded shock body stops and the top cap of the shock starts, down and make a mark for your rear cross over ring location. Next, slide the spring adaptor on (Fox) and install the rear cross over rings with the O-ring groove facing the bottom of the shock. Tighten the cross over and install the O-ring. Now, install the upper spring, nylon divider with the

4 long side facing the bottom of the shock, then the lower spring. Use the spring compressor and install the lower spring perch and lower adaptor (Fox). Release the spring compressor and thread the pre-load collar down to the pre-load distance listed on the first page. Now you can install the rear shocks on the car. Installing your shocks with the new springs is a pretty straight forward thing to do but there are some adjustments to the ride height that you must follow to ensure that your RZR is at the correct height for best performance. All RZRs are different weights depending on the accessories you have on it so you may need to adjust them a little to get your ground clearance correct. Once you have your shocks installed you must drive it to settle the suspension for any ground clearance measurements. Just pushing the RZR up and down a few times will not work! Once you have driven at least 100 yards or so then pull into your driveway or any other flat and hopefully level spot, slowly without using much, if any brakes so as not to cause the front to dip down for the measurement. Hop out and grab your tape measure. Check the rear of the RZR by measuring from the bottom of the frame to the ground, in the center of the chassis at the rear. This should be about 12 off the ground. Now measure the front at the bottom of the frame just behind the lower control arm mount and forward of the firewall. This should be 12.5 to 13 off the ground. The front should be higher because we want the RZR to be level or a bit higher than the rear with you are sitting in it. This means it will be an inch to.5 higher than the rear when empty.

5 See the pictures above and on the right to make sure you are measuring in the correct spots. If your RZR is sitting too low or too high then jack it up and adjust the preload collar accordingly. You can often spin the collar by hand just by grabbing the springs and twisting them and the collar together. If you have Fox shocks then use a standard screw driver to unlock the two preload collars and spin them up or down according. With Walker shocks you can use an extension in the pre-load collar holes to spin them. Any adjustment to the collar will change the ride height about double the amount you move the collar. For instance, if you move the preload collar down ½ it will raise the RZR about 1. Your springs are NEW and they will settle a bit with use. After about 200 miles they will be where they like to be permanently. Please check your ride height at around 100 and again at 200 miles and make more preload adjustments as needed. Never raise or lower the RZR to make the suspension stiffer or looser! The spring s job is to hold it up. All other tuning is done with the compression adjustor on the shock or the Silent cross over rings inside the upper coil spring. Now that you have the ride height dialed in lets go through the shock tuning procedure. Our goal with your new set up is to get the softest, most plush ride through all terrain as possible so that you don t feel the bumps, rocks, tracks, ect. For this reason start with all of the compression adjusters all the way loose or counter clockwise. This will be your softest ride. On a Walker shock the adjuster is a large knob on the reservoir of the shock you can turn by hand. On a Fox shock the adjuster can be a blue plastic knob or it can be a small adjuster that requires a standard screw driver to move it. Now pick your favorite trail and drive the RZR like you normally do. If it doesn t bottom out on the big hits or G outs then great, leave it where it is! But if you bottom out the front 6 or 7 times in a 30 minute blast then you need to add some compression to the shock. Turn the compression adjuster 2-3 clicks stiffer which is clockwise. Only adjust the front. There is no reason to stiffen up the back if the front is bottoming. Now run the same trail again and if the bottoming has stopped then you are done! If it still bottoms out a bit then add 2-3 clicks of compression until it stops. Same goes for the rear if it is the one that bottoms out the most. Just add 2-3 clicks of

6 compression on the adjuster until it stops. Now if you bottom out the RZR 1 time in an hour ride we would call that perfect. Anything can be bottomed out if you make a big mistake. At least you know where the limit is and the ride is as plush and smooth as it can be for 99% of everything you do. For the more advanced suspension tuners, you can play with the silent cross over rings as well. They control when, though compressing your suspension, the heavier lower spring comes into play and makes your suspension considerably stiffer. We set the collars location at an all-around, great place that we have found through testing. But, you can adjust it to suit your driving style too. The higher up the shock you run the collar the longer the suspension will remain soft and plush. The negative to this is that the higher up the shock you run the collar the more body roll you will get, the more front dive or rear squat you will get and the less help in the bump stage or big hits you will get. The lower you run the collar the quicker the suspension will move from soft to stiff. The advantage to this is less front dive or rear squat, less body roll and more help in the big hits without turning up the compression knob on the shocks. This may be a perfect thing if you are racing short course. The negative to this is that the plush ride will go away very quickly and the chatter and stiffness will start to creep back into your seat soon. Don t worry, all of these adjustments can always go back to where you started just by moving them back. Feel free to experiment and see what you like or dislike. Finally, more weight will make the RZR bottom out sooner so experiment with your shock adjusters to accommodate for more passengers. As a rule of thumb, we add 2-3 clicks of compression to the front if you add a 180lb passenger. If you have a 4 seater then you may add 1-2 clicks to the rear shocks for one rear passenger and 2-3 clicks for two rear passengers. These settings should compensate for the added weight so you can keep your speeds the same as you would by yourself. The cross over rings are designed to be rubbed by the coil springs. As the spring compresses it vibrates side to side and can rub the cross over ring. This is normal. Sometimes the springs don t sit perfectly flat on the plastic divider. You will notice this by looking at the plastic spring divider when the car is on the ground. If it is fairly straight with the shock body your good to go. But if it is

7 sitting sideways a bit then you can clock the springs differently to help this. Jack the car up and clock the upper and lower springs 90 degrees apart from each other by twisting them by hand instead of 180 degrees apart. This may get the divider to sit straighter and allow the upper spring to rub the cross over ring less. That s it. You are now all set to run and adjust your RZR like a pro! Experiment to try things and see what you prefer. Remember just put everything back to full soft, and start over if you lose your way on the adjustments. We hope this kit helps to make you the fastest and smoothest person in your group. Now go show off and have fun! Thank you.

Spring manual V3.1 ENGLISH

Spring manual V3.1 ENGLISH Spring manual V3.1 ENGLISH HYPERPRO TOOLS, used in this manual: Tool Description Part no. A, B, C Cartridge fork spring removal tool kit HP-T01 D Big Piston Fork end cap socket 45mm HP-T102 E Big Piston

More information

TOO TECH RACING SET-UP INSTRUCTIONS (For Non Twin Chamber Showa & KYB)

TOO TECH RACING SET-UP INSTRUCTIONS (For Non Twin Chamber Showa & KYB) TOO TECH RACING SET-UP INSTRUCTIONS (For Non Twin Chamber Showa & KYB) STEP 1: Measure suspension "Race Sag". (Most important adjustment there is) First: Put the bike on a center stand and release the

More information

Street-Lynx By. Reilly MotorSports, Inc. Installation Manual

Street-Lynx By. Reilly MotorSports, Inc. Installation Manual Street-Lynx By Reilly MotorSports, Inc. Installation Manual 1 1- Begin by removing your original rear suspension disconnect your brake lines, E-brake cables, and remove the driveshaft. To prevent fire

More information

C5/C6 Level 3 Coilover

C5/C6 Level 3 Coilover Part # 11510311-1998-2013 C5/C6 Level 3 CoilOver System Front Components: 11513111 Front Coilovers Recommended Tools Rear Components: 11516111 Rear Coilover Miscellaneous Components: 85000000 Spanner Wrench

More information

RZR XP 1000 Turbo Full Spring Kit

RZR XP 1000 Turbo Full Spring Kit RZR XP 1000 Turbo Full Spring Kit Polaris RZR XP 1000 Turbo 2016+ Part #: 5301154, 5301164, 5301174, 5301184, 5301194 Rev. 062018 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail:

More information

Part # GM F-Body Rear CoilOvers

Part # GM F-Body Rear CoilOvers Part # 1116111-198-00 GM F-Body Rear CoilOvers Recommended Tools 8-0 F-Body TQ Series Rear Coilovers Table of contents Page... Included components Page 3... Hardware List and Getting Started Page 4...

More information

For all Ram x4 Trucks, and all Ram x4 trucks.

For all Ram x4 Trucks, and all Ram x4 trucks. Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD 5 th GEN STEERING KIT

More information

Installation Instructions Camaro Level 2 Coilover. Part # Camaro Level 2 CoilOver System.

Installation Instructions Camaro Level 2 Coilover. Part # Camaro Level 2 CoilOver System. Part # 00-99-00 Camaro Level CoilOver System Front Components: 0 Front CoilOver Strut Recommended Tools Rear Components: 60 Rear Coilover Miscellaneous Components: 85000000 Spanner Wrench 99-00 Camaro

More information

DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS

DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION

More information

Cane Creek Double Barrel Instructions

Cane Creek Double Barrel Instructions Cane Creek Double Barrel Instructions Congratulations on your purchase of the Cane Creek Double Barrel rear shock. Developed in partnership with Öhlins Racing, the Double Barrel brings revolutionary suspension

More information

C5/C6 Level 2 Coilover

C5/C6 Level 2 Coilover Part # 5020-998-203 C5/C6 Level 2 CoilOver System Front Components: 530 Front Coilovers Recommended Tools Rear Components: 560 Rear Coilover Miscellaneous Components: 85000000 Spanner Wrench 998-203 C5/C6

More information

Step 5 Install the frame rail insert into the frame.

Step 5 Install the frame rail insert into the frame. COR-6372S, COR-6372D 63-72 C-10 Rear Coil-over KIT Tool s for the job Car Lift Floor Jack Chalks Jack Stands Standard Wrench set Standard Socket set Spring Compressor Phneumatic/ Electric Grinder Phneumatic/

More information

2006 RockShox Pike 454 Air U-turn

2006 RockShox Pike 454 Air U-turn a Guest Review by DGC Edited by Chris Streeter FEATURES The Maxle is possibly the best thing to come along on since external adjustable rebound. This is a true quick-release, 20mm thru-axle system. 5 seconds

More information

EZRyde Rear Suspension Adjustment and Tuning Manual

EZRyde Rear Suspension Adjustment and Tuning Manual EZRyde Rear Suspension Adjustment and Tuning Manual Track Tension 1. Support the rear of the snowmobile with a track stand or equivalent sturdy stand. 2. Hook a spring scale around a track clip at mid-span:

More information

Our goal is to make the install a breeze. Please read the entire guide before beginning.

Our goal is to make the install a breeze. Please read the entire guide before beginning. www.airkewld.com Page 1 of 6 IRS Axle Kit Install IRS Axle Kit Install Our goal is to make the install a breeze. Please read the entire guide before beginning. KITS SHOULD INCLUDE 2 - Control-arm mounting

More information

Shock manual V3.1 ENGLISH

Shock manual V3.1 ENGLISH Shock manual V3.1 ENGLISH 2 Shock manual v3.1 INDEX Page Hyperpro Shock Overview 4 Maintenance 5 Rear Shock unit, removal and installation M1 Mono shock (& Telelever front) 6 M2 Twin shock 6 M3 Link system

More information

Detroit Speed, Inc. DSE/JRi Front Strut Kit Camaro/Firebird P/N: & D

Detroit Speed, Inc. DSE/JRi Front Strut Kit Camaro/Firebird P/N: & D Detroit Speed, Inc. DSE/JRi Front Strut Kit 1982-92 Camaro/Firebird P/N: 030332 & 030332D The DSE/JRi Front Strut Kit is a high-performance aluminum body strut body with Detroit Tuned valving. The kit

More information

Adjustable Tie-rod Ends (Mm5TR-1)

Adjustable Tie-rod Ends (Mm5TR-1) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005-10 Adjustable Tie-rod Ends (Mm5TR-1) 3. Remove the front wheels. 4. Loosen

More information

Detroit Speed, Inc. Detroit Speed/JRi Front Strut Kit Camaro/Firebird P/N: & D

Detroit Speed, Inc. Detroit Speed/JRi Front Strut Kit Camaro/Firebird P/N: & D Detroit Speed, Inc. Detroit Speed/JRi Front Strut Kit 1982-92 Camaro/Firebird P/N: 030332 & 030332D The Detroit Speed/JRi Front Strut Kit is a high-performance aluminum body strut body with Detroit Tuned

More information

9th Gen Honda Civic INSTALLATION GUIDE Civic, Civic Si Kit Civic Si Kit Front Application

9th Gen Honda Civic INSTALLATION GUIDE Civic, Civic Si Kit Civic Si Kit Front Application 9th Gen Honda Civic 2012-15 Civic, 2012-13 Civic Si Kit 78526 2014+ Civic Si Kit 78556 Front Application INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely

More information

RZR XP 1000 HD Radius Rod Kit

RZR XP 1000 HD Radius Rod Kit RZR XP 1000 HD Radius Rod Kit Polaris RZR XP 1000 2014-2016 Part #: 5201509 Rev. 111517 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING

More information

# C5/C6

# C5/C6 Part # 00-998-0 C/C Level CoilOver System Front Components: 0 Front Coilovers Recommended Tools Rear Components: 0 Rear Coilover Miscellaneous Components: 8000000 Spanner Wrench 998-0 C/C Level Coilover

More information

RZR Full Spring Kit

RZR Full Spring Kit RZR 800 50 Full Spring Kit Polaris RZR 800 50 2008-2013 Part #: 5301204, 5301214 Rev. 082417 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY

More information

RZR Full Spring Kit

RZR Full Spring Kit RZR 900 50 Full Spring Kit Polaris RZR 50 2015+ Part #: 5301105, 5301115 Rev. 082317 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING

More information

Improves Traction and Lateral G s

Improves Traction and Lateral G s Tuesday, February 14, 2012 New Product Release: Griggs/VariShock Improves Traction and Lateral G s Double-Adjustable Ultra-Light Coil-Over Shock Absorbers Available NOW!! Can be used on any high performance

More information

Index. Page Number Section

Index. Page Number Section S H O C K S Index Page Number Section 1-4 GM Front Coil Over Installation 5-7 Front Smooth Body Shock Installation 7-8 Rear Smooth Body Shock Installation 8-11 Custom Coil Over Installation 12 Tuning and

More information

page 3 SCRATCH COIL 9, SCRATCH COIL 7

page 3 SCRATCH COIL 9, SCRATCH COIL 7 SCRATCH SUSPENSION SETUP GUIDE page 2 SCRATCH Air 8, Scratch AIR 6 page 3 SCRATCH COIL 9, SCRATCH COIL 7 page 4 Coil fork setup page 5 Coil SHOCK setup Suspension Setup Guide (Scratch 9, Scratch 7) Bike

More information

QuickTrick Alignment Tools

QuickTrick Alignment Tools QuickTrick Alignment Tools QuickTrick Alignment Kits are Professional quality tools designed for a lifetime of reliable service. QuickTrick Kits can be used on any vehicle for measurement of the alignment

More information

August 2001 THINGS THAT MAKE SPRING CHANGES WORK BACKWARDS

August 2001 THINGS THAT MAKE SPRING CHANGES WORK BACKWARDS August 2001 WELCOME Mark Ortiz Automotive is a chassis consulting service primarily serving oval track and road racers. This newsletter is a free service intended to benefit racers and enthusiasts by offering

More information

QA1 MOD Series Shock Installation and Quick Tuning Guide

QA1 MOD Series Shock Installation and Quick Tuning Guide QA1 MOD Series Shock Installation and Quick Tuning Guide 9919-237 Rev. 10092018 Introduction Congratulations on your purchase of QA1 s double adjustable MOD Series shocks with low-speed bleed adjustment!

More information

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System.

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System. Part # 22020-979-989 Mustang Level 2 CoilOver System Front Components: 2230 Front CoilOver Strut Recommended Tools Rear Components: 2260 Rear Coilover 225899 Rear Lower StrongArms 226699 Rear Upper StrongArms

More information

2013 RT / 2014RT / 2015 RT - Shock Spring Adjuster Installation Instructions

2013 RT / 2014RT / 2015 RT - Shock Spring Adjuster Installation Instructions 2013 RT / 2014RT / 2015 RT - Shock Spring Adjuster Installation Instructions Billet Aluminum Adjusters (2) Shock Spring Compressors (Optional) Spanner Wrench (1) BajaRon Decals Not Shown (4) Adjuster Scuff

More information

#0980 Intimidator 7 Direct Drive Racing Kit

#0980 Intimidator 7 Direct Drive Racing Kit #0980 Intimidator 7 Direct Drive Racing Kit 1 Thank you for purchasing the Intimidator 7! Within this kit you will find a race winning car with over 30 years of Custom Works design and quality. The latest

More information

Front Suspension Redo

Front Suspension Redo Front Suspension Redo Message: First, thanks to all the previous posters for guidance in my doing the suspension. As thanks, here s the updated document for doing the front suspension. Procedure: While

More information

Looking up the front of the engine from under the radiator. (Picture taken with belt under tension.)

Looking up the front of the engine from under the radiator. (Picture taken with belt under tension.) 8. If you re replacing the AC compressor drive belt as well, it s time to loosen its belt tensioner. The AC compressor belt tensioner is very obvious under the front of the car. Loosen the 13mm bolt, then

More information

LG CORVETTE GT2 COIL OVERS

LG CORVETTE GT2 COIL OVERS LG CORVETTE GT2 COIL OVERS THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Parts Inventory: 1. Assembled Front shock and spring 2. Assembled Rear shock and spring

More information

Fork Set-Up Guide DVOSUSPENSION.COM

Fork Set-Up Guide DVOSUSPENSION.COM Fork Set-Up Guide DVOSUSPENSION.COM Fork Set-Up Guide for Other Languages Pre-Ride Check DOWNLOAD FRANÇAIS ITALIANO DEUTSCH ESPAÑOL Guide d ajustement Guida di sintonia Tuning guide Guía de ajuste 6. Compress

More information

MM Rear Coil-Over Kit - Bilstein Shocks (MMCO-3)

MM Rear Coil-Over Kit - Bilstein Shocks (MMCO-3) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Rear Coil-Over Kit - Bilstein Shocks (MMCO-3) Read all instructions before

More information

Thanks for Ordering The Kawasaki KLX Adjustable Lowering Kit From

Thanks for Ordering The Kawasaki KLX Adjustable Lowering Kit From www.scootworks.com Thanks for Ordering The Kawasaki KLX Adjustable Lowering Kit From READ THIS BEFORE UNPACKING YOUR KIT! This instruction booklet contains detailed steps for installing the rear suspension

More information

Team Associated RC10B4 Tuning Guide

Team Associated RC10B4 Tuning Guide Team Associated RC10B4 Tuning Guide This document is a compilation of released pages from Associated Electric made for PetitRC, all credits must go to Associated Electric. Complete Tuning Guide: B4 Front

More information

Setup Guide and Chassis Tuning Tips (simple version) By Jim Daniels

Setup Guide and Chassis Tuning Tips (simple version) By Jim Daniels This document is released into the public domain and may be reproduced and distributed in its entirety so long as all credit to Jim Daniels remains. If you find this guide helpful please consider donating

More information

Kit 78631/ Hyundai Genesis Coupe

Kit 78631/ Hyundai Genesis Coupe Kit 78631/ 78632 Hyundai Genesis Coupe Rear Application (with and without shocks) (011609) ERN 8124 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before

More information

SUSPENSION SETUP GUIDE

SUSPENSION SETUP GUIDE For your Pivot suspension equipped bike to pedal and descend at its best, it is important to tune the suspension properly. Use this guide to familiarize yourself with the Pivot suspension setup procedures

More information

Welcome and enjoy tuning your Manitou ABS+ Compression Damping System! Purposefully engineered to raise your expectations.

Welcome and enjoy tuning your Manitou ABS+ Compression Damping System! Purposefully engineered to raise your expectations. Welcome and enjoy tuning your Manitou ABS+ Compression Damping System! Purposefully engineered to raise your expectations. PLEASE READ SERVICE INSTRUCTIONS PRIOR TO BEGINNING WORK. While revalving your

More information

Detroit Speed, Inc. QUADRA Link Rear Suspension Camaro/Firebird P/N:

Detroit Speed, Inc. QUADRA Link Rear Suspension Camaro/Firebird P/N: Detroit Speed, Inc. QUADRA Link Rear Suspension 1967-1969 Camaro/Firebird P/N: 041703 Figure 1 Item Component Quantity 1 Upper Link Front Pocket-Left 1 2 Upper Link Front Pocket-Right 1 3 Upper Shock Crossmember

More information

www.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm

More information

PS-8300-DA Shock, Double-Adjustable Remote & Piggyback TECHNICAL MANUAL

PS-8300-DA Shock, Double-Adjustable Remote & Piggyback TECHNICAL MANUAL PS-8300-DA Shock, Double-Adjustable Remote & Piggyback TECHNICAL MANUAL Main Office 150 Franklin St. P.O. Box 1056 Reading, PA 19603 (610) 375-6180 (610) 375-6190 Fax Table of Contents: PS 8300RM/PB DOUBLE

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

FLOAT 3 EVOL RC2 FACTORY SERIES OWNERS MANUAL

FLOAT 3 EVOL RC2 FACTORY SERIES OWNERS MANUAL FLOAT 3 EVOL RC2 FACTORY SERIES OWNERS MANUAL Contents CONGRATULATIONS... 3 CONSUMER SAFETY... 3 UNDERSTANDING THE FLOAT 3 EVOL RC2... 4 FOX PUMP... 5 OPTIONS... 5 ADJUSTABLE PROGRESSIVE DUAL-STAGE AIR

More information

SUSPENSION SETUP GUIDE

SUSPENSION SETUP GUIDE For your Pivot suspension equipped bike to pedal and descend at its best, it is important to tune the suspension properly. Use this guide to familiarize yourself with the Pivot suspension setup procedures

More information

MM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4)

MM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4) The lower spring perch is drilled

More information

2011+ Adjustable Tie-rod Ends (Mm5TR-2)

2011+ Adjustable Tie-rod Ends (Mm5TR-2) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2011+ Adjustable Tie-rod Ends (Mm5TR-2) Instructions 1. Set the parking brake

More information

Assembly Manual. 1/10th Formula 1 Car

Assembly Manual. 1/10th Formula 1 Car Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp

More information

J&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions

J&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions J&M Mustang Adjustable Panhard Rod (05-09) - Installation Instructions The below installation instructions work for the following products: J&M Mustang Adjustable Panhard Rod (05-09) Please read through

More information

1204AA Ford Mustang Double Adjustable Trailing Arms

1204AA Ford Mustang Double Adjustable Trailing Arms 1204AA 79-04 Ford Mustang Double Adjustable Trailing Arms Special Tools Required for this Installation - 4 post lift or alignment rack preferable - Air Chisel, Angle Finder (Digital Preferred), Dead blow

More information

Detroit Speed, Inc. Front Coilover Kit Race Double Adjustable Camaro P/N:

Detroit Speed, Inc. Front Coilover Kit Race Double Adjustable Camaro P/N: Detroit Speed, Inc. Front Coilover Kit Race Double Adjustable 2010+ Camaro P/N: 030321 Item Quantity Description 1 2 Front Strut Assembly (Double Adjustable) 2 2 Coilover Spring 250# x 2.5"ID x 8"L 3 2

More information

INSTRUCTION S G-Comp Front Suspension: Chevy Camaro Speedway Motors, Inc Kit Contents:

INSTRUCTION S G-Comp Front Suspension: Chevy Camaro Speedway Motors, Inc Kit Contents: INSTRUCTION S 350-500 G-Comp Front Suspension: 70-81 Chevy Camaro Speedway Motors, Inc. 2017 Kit Contents: 350500.1 G-Comp Subframe, Camaro 350500.2 G-Comp Sway Bar Kit, Camaro 350500.3 Hardware Kit, G-Comp

More information

Detroit Speed, Inc. QUADRA Link Rear Suspension Camaro/Firebird P/N:

Detroit Speed, Inc. QUADRA Link Rear Suspension Camaro/Firebird P/N: Detroit Speed, Inc. QUADRA Link Rear Suspension 1967-1969 Camaro/Firebird P/N: 041703 The Detroit Speed Inc., QUADRA Link rear suspension system is a great way to upgrade from an original leaf spring rear

More information

STEP #1: Remove the wheels from the truck. There are (6) 21mm lug nuts holding each wheel on... Remember Lefty Loosy, Righty Tighty.

STEP #1: Remove the wheels from the truck. There are (6) 21mm lug nuts holding each wheel on... Remember Lefty Loosy, Righty Tighty. - CustomTacos.com Page 1 of 36 How-To: Toytec Lift Install Read all of these install instructions prior to installing Toytec's suspension lift. I cannot be held responsible for any damages or personal

More information

2005 to 2008 #08 Metric Nova Chassis Set Up Sheet

2005 to 2008 #08 Metric Nova Chassis Set Up Sheet Springs 1 2005 to 2008 #08 Metric Nova Chassis Set Up Sheet Flat end of spring down on tubular lower a-arms. Left Front 800lb. Right Front 750lb. Left Rear 200lb. Right Rear 225lb. On Top of Tube Axle

More information

3 AND 5 LINK INSTALLATION MANUAL

3 AND 5 LINK INSTALLATION MANUAL 1127 E. Curry Rd. #3 Tempe, Arizona 85281 (480) 446-8442 www.levyracing.com 3 AND 5 LINK INSTALLATION MANUAL Thank you for your purchase of this Levy Racing quality product. Like all Levy Racing products,

More information

Commander XT/ Max Full Spring Kit

Commander XT/ Max Full Spring Kit Commander XT/ Max Full Spring Kit Can Am Commander XT/ Max 2011+ Part #: 5302104, 5302114, 5302124 Rev. 083117 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com

More information

Moddit. How to Install Stance Coilovers on a Subaru

Moddit. How to Install Stance Coilovers on a Subaru Moddit How to Install Stance Coilovers on a Subaru BRZ Let's get LOW (and maybe lighter and stiffer suspension)! In this article, we will install Stance ST- ZN6-XS Coilovers on the FRSport Subaru BRZ.

More information

Retro it Steering Column

Retro it Steering Column Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010

More information

Kit Lexus LS 400 (UCF10 and UCF20)

Kit Lexus LS 400 (UCF10 and UCF20) Kit 78659 Lexus LS 400 (UCF10 and UCF20) Rear Application MN-1032 (011701) ERN 8585 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding

More information

FOX Racing Shox Bypass Technical Manual.

FOX Racing Shox Bypass Technical Manual. FOX Racing Shox Bypass Technical Manual. The following technical manual will be using a 2.5 dia. shock with three tubes for descriptions and illustrations. Your shock may differ in the number of tubes,

More information

X4-X7 Hyper 600cc Chassis Setup Guide

X4-X7 Hyper 600cc Chassis Setup Guide Suggested Starting Setup on a Normal Condition 1/6 or 1/8 Mile Track, Winged Left Front Right Front Left Rear Right Rear Torsion Bar Size (+ Turns).675 (+0).675 (+0).725 (+0).750 (+1) Coil Size (+ Turns)

More information

After installation please observe the following points: Before installation please observe the following points:

After installation please observe the following points: Before installation please observe the following points: Before installation please observe the following points: Read all information in this manual carefully. All suspension components are fitted and removed acc. to the manufacturer s specifications for installing

More information

OWNERS MANUAL HEADSHOK FORKS

OWNERS MANUAL HEADSHOK FORKS OWNERS MANUAL HEADSHOK FORKS 1998 HEADSHOK MOTO FR INSTRUCTIONS The HeadShok Moto FR combines the versatility of a triple-clamp fork with the superior stiction-free performance of all the HeadShok forks.

More information

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS

More information

Spikes-Spider Hub Installation

Spikes-Spider Hub Installation Spikes-Spider Hub Installation The instructions that are provided with the Spikes Spiders are pretty good. I've created this page for two reasons: to show those that are thinking of buying a set exactly

More information

E.C.C. and AirTail Compressor Kit For the Airtail Suspension System Setup Instructions

E.C.C. and AirTail Compressor Kit For the Airtail Suspension System Setup Instructions E.C.C. and AirTail Compressor Kit For the Airtail Suspension System Setup Instructions Note: Please read and follow the Installation Instructions first, then read and follow these Setup Instructions completely

More information

Global West Suspension 655 South Lincoln Ave San Bernardino Ca Phone Fax Web address globalwest.

Global West Suspension 655 South Lincoln Ave San Bernardino Ca Phone Fax Web address globalwest. Global West Suspension 655 South Lincoln Ave San Bernardino Ca. 92408 Phone 877-470-2975 Fax 909-890-0703 Web address globalwest.net Mustang coilover instruction sheets for 64-66 Kit includes the following

More information

84-86 Ford SVO Mustang AC Installation Guide

84-86 Ford SVO Mustang AC Installation Guide 84-86 Ford SVO Mustang AC Installation Guide This installation guide is for the AC installation kit from Late Model Restoration. The Vendor is Hose Wizards that manufactures this great kit that provides

More information

STOP---READ THIS FIRST!

STOP---READ THIS FIRST! STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2011-13 FORD F-250 & F350 6 & 8 LIFT KITS 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196 (559) 277-0457 FAX www.mcgaughys.com

More information

INSTRUCTION G-Comp Rear Suspension: Chevy Camaro. Kit Contents:

INSTRUCTION G-Comp Rear Suspension: Chevy Camaro. Kit Contents: INSTRUCTION 350-700 G-Comp Rear Suspension: 70-81 Chevy Camaro Speedway Motors, Inc. 2017 Kit Contents: 350700.1 G-Comp Crossmember & Chassis Brace 350700.2 G-Comp Rear Crossmember Assembly 350700.3 G-Comp

More information

INSTALLATION INSTRUCTIONS CHEVY C-10 4-Link Rear End

INSTALLATION INSTRUCTIONS CHEVY C-10 4-Link Rear End INSTALLATION INSTRUCTIONS 73-87 CHEVY C-10 4-Link Rear End Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating to ensure proper

More information

STOP---READ THIS FIRST!

STOP---READ THIS FIRST! STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2007-2013 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART# 50700 & 50720) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196

More information

Installation Instructions for BMR Lowering Springs Performance ( Mustang GT)

Installation Instructions for BMR Lowering Springs Performance ( Mustang GT) Installation Instructions for BMR Lowering Springs Performance (2015-2017 Mustang GT) Time Required: 3+ hours Notes: This install was done with the performance springs from BMR, but install should be the

More information

Sport Sway Bar Kit Mustang

Sport Sway Bar Kit Mustang Sport Sway Bar Kit 22102 2005 Mustang Installation of Hotchkis Front Sway Bar 1F Raising Vehicle Securely block the rear wheels of the vehicle. Use a jack to lift up the front of the vehicle and use jack

More information

1. Remove the front struts by first disconnecting the ABS wire and brake line(retain hardware) from the factory strut.

1. Remove the front struts by first disconnecting the ABS wire and brake line(retain hardware) from the factory strut. Part # 12153111-2005 up Mustang Recommended Tools 2005-up Mustang Front TQ CoilOver Strut Installation Table of contents Page 2... Included components Page 3... Disassembly and Getting Started Page 4...

More information

UNDERDOG RACING DEVELOPMENT URD Traction Bar Installation

UNDERDOG RACING DEVELOPMENT  URD Traction Bar Installation URD Traction Bar Installation Introduction: UNDERDOG RACING DEVELOPMENT Thank you for choosing the URD Traction Bar for two wheel drive street trucks. More models coming soon! This bar is a true bolt on

More information

Detroit Speed, Inc. QUADRA Link Rear Suspension Nova P/N:

Detroit Speed, Inc. QUADRA Link Rear Suspension Nova P/N: Detroit Speed, Inc. QUADRA Link Rear Suspension 1968-1974 Nova P/N: 041704 The Detroit Speed Inc., QUADRA Link rear suspension system is a great way to upgrade from an original leaf spring rear suspension.

More information

Steeda S550 Mustang Front Coilover Installation Instructions For Part:

Steeda S550 Mustang Front Coilover Installation Instructions For Part: Steeda S550 Mustang Front Coilover Installation Instructions For Part: 555-8170 Tools required 1. Jack 2. Jack stands 3. Torque Wrench 4. 10mm wrench 5. 11mm wrench 6. 17mm wrench 7. 18mm socket 8. Plastic

More information

Learning to Set-Up Your Warrior Drive Belt Arizona Warrior (Rev4) BEFORE GETTING STARTED

Learning to Set-Up Your Warrior Drive Belt Arizona Warrior (Rev4) BEFORE GETTING STARTED BEFORE GETTING STARTED 1. A noise one guy calls 'howling' is the same noise another guy calls 'squealing' so unless you are both hearing the noise with your own ears its better to not assume a drive belt

More information

EVO-1108 EVO MFG Front Bolt-On Coilover Kit

EVO-1108 EVO MFG Front Bolt-On Coilover Kit EVO-1108 EVO MFG Front Bolt-On Coilover Kit 1 EVO-11090B Driver Shock Mount Tower 1 EVO-11091B Pass Shock Mount Tower 1 EVO-11092B Pass Lower B/O C/O Mount 1 EVO-11092DB Driver Lower B/O C/O Mount 2 EVO-12022CZ

More information

Speakers and Motors. Three feet of magnet wire to make a coil (you can reuse any of the coils you made in the last lesson if you wish)

Speakers and Motors. Three feet of magnet wire to make a coil (you can reuse any of the coils you made in the last lesson if you wish) Speakers and Motors We ve come a long way with this magnetism thing and hopefully you re feeling pretty good about how magnetism works and what it does. This lesson, we re going to use what we ve learned

More information

COBB WRX Sports Springs West 1820 South Salt Lake City, UT USA (801)

COBB WRX Sports Springs West 1820 South Salt Lake City, UT USA (801) COBB 3362 West 1820 South Salt Lake City, UT 84104 USA (801) 713-0035 2008 WRX Sports Springs Congratulations on your purchase of the COBB Sports Springs. The following instructions should assist you through

More information

2014 GM 1500 TRUCK STOP---READ THIS FIRST! 7" Lift KIT. **Read These Entire Instructions Before Starting Anything**

2014 GM 1500 TRUCK STOP---READ THIS FIRST! 7 Lift KIT. **Read These Entire Instructions Before Starting Anything** STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2014 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART #50768 & #50769 ) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196

More information

Detroit Speed, Inc. Rear Coilover Kit Camaro P/N: , D

Detroit Speed, Inc. Rear Coilover Kit Camaro P/N: , D Detroit Speed, Inc. Rear Coilover Kit 2010-15 Camaro P/N: 042430, 042430-D The Detroit Speed, Inc. 2010-15 Camaro rear coilover kit is a direct bolt-on assembly that completely replaces the OEM rear strut

More information

FLOAT 3 EVOL, R, RC, RC2 FACTORY SERIES AFTERMARKET SHOCK OWNER S MANUAL

FLOAT 3 EVOL, R, RC, RC2 FACTORY SERIES AFTERMARKET SHOCK OWNER S MANUAL FLOAT 3 EVOL, R, RC, RC2 FACTORY SERIES OWNERS MANUAL 2.5 PODIUM-X AFTERMARKET SHOCK OWNER S MANUAL CONTENTS CONGRATULATIONS... 3 CONSUMER SAFETY... 3 UNDERSTANDING THE FLOAT 3 EVOL SERIES... 4 FOX PUMP...

More information

INSTRUCTION G-Comp Unser Edition Rear Suspension: Chevy Nova. Kit Contents:

INSTRUCTION G-Comp Unser Edition Rear Suspension: Chevy Nova. Kit Contents: INSTRUCTION 350-400 G-Comp Unser Edition Rear Suspension: 62-67 Chevy Nova Speedway Motors, Inc. 2017 Kit Contents: 350003.1 G-Comp Chassis Brace 350003.2 G-Comp Front Support 350400.1 Chevy II Unser Rear

More information

Eibach Pro-System-Plus

Eibach Pro-System-Plus Eibach Pro-System-Plus Tools : - Floor Jack - 3 Jack Stands (4 preferred) - 2 wheel stoppers - Car wrench set - Fire torch - Bolt thread locker (use on every bolt you tight) Disclaimer: This guide is not

More information

Installation Instructions

Installation Instructions Part # 11210299-1993-2002 GM F Body Level 2 Shockwave System Front Components: 11212401 Front Shockwaves Recommended Tools Rear Components: 11215401 Rear Shockwaves Compressor System 30334000 Digital 3

More information

Owners manual. Öhlins Superbike front fork FG 170

Owners manual. Öhlins Superbike front fork FG 170 Owners manual Öhlins Superbike front fork FG 0 Including: Setting up your fork Changing springs and seals Service the fork Trouble shooting Technical info Spare parts & tools Öhlins super bike front fork

More information

OTK CHASSIS- SET UP GUIDE

OTK CHASSIS- SET UP GUIDE OTK CHASSIS- SET UP GUIDE Introduction This setup guide is created to facilitate a user of OTK equipment to reach an optimal chassis setup and on-track performance. The different tuning possibilities and

More information

Tacoma Front Suspension Install Instructions

Tacoma Front Suspension Install Instructions 1995-04 Tacoma Front Suspension Install Instructions Important notices: These instructions are intended only as a general guide for installing All-Pro products. For some items, specialized mechanical skills,

More information

QUICKTRICK PRODUCT IN- STRUCTIONS ALIGNMENT SIMPLE SOLUTIONS. Mr & Mrs QuickTrick. Made in the USA

QUICKTRICK PRODUCT IN- STRUCTIONS ALIGNMENT SIMPLE SOLUTIONS. Mr & Mrs QuickTrick. Made in the USA QUICKTRICK PRODUCT IN- ALIGNMENT SIMPLE SOLUTIONS Thank you for your support of QuickTrick products. You are supporting an American Dream business grown from the Garage and the race track to a World Wide

More information

.050 Allen key 1.5mm Allen key 1/16 Allen key 5/64 Allen key 3/32 Allen key Turnbuckle & 3/16 wrench

.050 Allen key 1.5mm Allen key 1/16 Allen key 5/64 Allen key 3/32 Allen key Turnbuckle & 3/16 wrench 1 Thank you for purchasing the Outlaw 4 Sprint Car! The Outlaw sprint car platform has been developed for loose dirt buggy tire racing. In this kit you will find the 4 th evolution of the car which features

More information

Retrofit Steering Column

Retrofit Steering Column Retrofit Steering Column INSTALLATION INSTRUCTIONS for 1965 Ford Falcon FOR PART NUMBER S: 1170906010, 1170906020, 1170906051, 1130906010, 1130906020, 1130906051 S INCE 1986 www.ididitinc.com 610 S. Maumee

More information