RMS. RMS18 Scaler SERIES -LP15 RMS SERIES SALES SPECIFICATIONS OPTIONS FEATURES & BENEFITS

Transcription

1 RMS SERIES SALES SPECIFICATIONS RMS SERIES -LP15 RMS18 Scaler FEATURES & BENEFITS AT A GLANCE Weights & Dimensions: Operating Weight Overall Tramming Length Overall Width ~ 45,365lb (20,700kg) ~ 34 (10.3m) 7 (2.1m) Tramming Height Carrier Articulation Inside Turning Radius 8-6 (2.6m) +/ (3.7m) Outside Turning Radius Boom Swing / Hammer Swing Maximum Horizontal Reach ~ 21-3 (6.5 m) +/ (12.9m) Note: Weights & dimensions are nominal and vary depending on final engine, operator s enclosure, & option configuration. Engine Configurations: 7 0 (2.1m) 8 6 (2.6m) Deutz BF4M1013EC 115hp 2300rpm Deutz BF4M1013EC (154hp / 2300rpm Caterpillar C4.4 ACERT 127hp 2200rpm Deutz BF6M1013EC (210hp / 2300rpm Breaker Specifications: BX10 Operating Frequency: Low: bpm / High: bpm Impact Energy: 1000 ft/lbs (1350 joules) Tool Width: 3.1 (78mm) (1.8m) (1.9m) Tramming Length 34 (10.3m) High speed / high mobility underground scaling. +/-45 vehicle articulation for tight turning radius. Torque converter/transmission package provides low profile engine shroud height for improved operator visibility. Mid-ship operator compartment provides good visibility for both tramming and scaling functions. Four heavy duty tube-in-tube self-leveling stabilizers provide quick set up times and stable operation. Purpose-built heavy duty, large cross-section boom provides excellent dexterity and strength when performing scaling functions. Good operation visibility for precise scaling operations. OPTIONS Protective operator structure Seating configurations Air intake system Exhaust system Fuel filling system Hydraulic filling system Wheel chocks Tires Fire suppression system Electric power pack Boom greasing system Breaker greasing system Dust suppression system Air Flush System Dozer blade Breaker ENG RMS SCALER BREAKER TECHNOLOGY 1

2 RMS18 SCALER COVERAGE SALES SPECIFICATIONS RMS SERIES Top View Maximum Hammer Reach 180 of Breaker Swing Parallel Coverage at back height: 18 ft (4.6 m) 180 of Boom Swing Hammer Reach with boom retracted Side View Maximum Breaker Tool Reach Optimum Scaling range with tool at 30 RMS18 Boom Swing Boom Swing: +/- 90 Hammer Swing: +/- 90 Maximum Horizontal Reach: 28-0 (8.5 m) Optimum scaler coverage is attained within the vertical breaking coverage area. While scaling, the carrier should be in a non-articulated state (in-line) with the front and rear jacks down. 2 BREAKER TECHNOLOGY RMS SCALER ENG-0112

3 RMS SERIES SALES SPECIFICATIONS RMS18 TURNING RADIUS RMS18 DRIVING & SCALING SPECS R (3.6m) 21-4 R (6.5m) 9-10 (3m) Turning Radius Turning radius: Outside 21-4 (6.5m) / Inside 12 (3.7m) Turning radius: +/- 45 articulation LP15 CARRIER - COMMON FEATURES NOTES: 12 R (3.7m) Boom should remain in-line with the carrier during tramming for optimum stability R (3.6m) Recommended Drift Height for Tramming BTI recommends a minimum drift height with cab : 9-10 (3m). CHASSIS LP15 articulated 4-wheel drive, all welded construction ENGINE END OSCILLATION +/- 8 c/w heavy framed external walking beam CARRIER ARTICULATION +/- 45 by two opposing 4 (100mm) bore x 2 (50mm) rod steering cylinders complete with stick steering control HYDRAULIC SYSTEM Variable displacement load sensing hydraulic piston pump In-line hydraulic pressure filter / In-line return filter for boom & tram functions. Air over oil fin type oil cooler c/w 24 VDC fan Independent hydraulic circuit for hydraulic breaker Fixed displacement gear pump for hydraulic breaker ELECTRICAL SYSTEM 24 VDC start/run 80A alternator (depends on engine drive) Murphy Power Vu instrument cluster for electronic engines 2x- LED red tram marker lights & 2x- LED head lights on engine end (1800 LUMENS) 2x- LED red tram marker lights & 2x- LED head lights on boom end (3500 LUMENS) 2x- LED working lights on boom end (1800 LUMENS) 2x- LED working lights on protective structure (3500 LUMENS) STABILIZERS Qty four 4 (100 mm) bore x 2 (50 mm) rod cylinder reinforced tube-in-tube construction providing 17 (432 mm) of stroke and side telescopic feature Operated by 3 valve spools, one per each boom end stabilizer & one operating both engine end stabilizers providing a self-leveling function SCALER BOOM Heavy duty RMS series mobile boom system Rugged boom sections c/w heavy duty hydraulic cylinders & rotary actuators Two-axis hammer movement, for precision scaling +/- 90 Turntable Swing / +/- 90 Hammer Swing Portable umbilical cord remote control pendant for boom and breaker functions BX10 breaker c/w heavy duty scaling housing c/w extended chisel tool for scaling ENG RMS SCALER BREAKER TECHNOLOGY 3

4 RMS CARRIER CONFIGURATIONS NOTES: SALES SPECIFICATIONS RMS SERIES POWERTRAIN GROUPS Deutz BF4M1013EC (115hp / 86kw) Caterpillar C4.4 ACERT (127hp / 95kw) Deutz BF4M1013EC (154hp / 113kw) Deutz BF6M1013EC (210hp / 154kw, high altitude performance) PROTECTIVE STRUCTURE ROPS/FOPS certified canopy - open air ROPS/FOPS certified fully enclosed cab full width, with HVAC heat/air conditioner for engine driven applications OPERATOR SEAT Suspension Seat, swivel Air Ride Seat, swivel PASSENGER SEAT No passenger seat Suspension Seat, mine duty passenger seat Air Ride Seat, mine duty passenger seat AIR INTAKE SYSTEM Air Intake Filter Air Intake Precleaner EXHAUST SYSTEM Catalytic exhaust Exhaust Manifold and Turbo Coating Exhaust System Wrap FUEL SYSTEM Fuel Tank, 50 gallon (189 liter) Fuel Tank with Fast Fill, 50 gallon (189 liter) HYDRAULIC TANK Hydraulic Tank, 50 gallon (189 liter) Separate Hydraulic Tank, 23 gallon (87 liter) for Breaker Hydraulic Tank with Fast Fill, 50 gallon (189 liter) TIRES Foam Filled tires: 12:00 x 20, 28 ply Solid tires: 12:00 x 20 FIRE SUPPRESSION SYSTEM No fire suppression Fire Extinguisher, 1 x 20 lb (9 kg) Ansul Fire Suppression system Ansul Fire Suppression with auto detection ELECTRIC POWER PACK No power pack Power Pack, 50 HP electric/hydraulic Power Pack with Cable Reel, 50 HP electric/hydraulic WHEEL CHOCKS No Wheel Chocks Aluminum Wheel Chocks BOOM GREASING SYSTEM Point of use grease fittings - no remote greasing points Boom Manual Lube system, boom system only Boom Auto-Lube system, boom system only Air flush system BREAKER GREASING SYSTEM Point of use grease fittings - no remote greasing points Breaker Auto-Lube System, breaker only DUST SUPPRESSION SYSTEM No Dust Suppression system On-board system - 35 gal (132 liter) water tank DOZER BLADE No Dozer Blade Dozer Blade 4 BREAKER TECHNOLOGY RMS SCALER ENG-0112

5 RMS SERIES SALES SPECIFICATIONS 6-5 (2.0m) POWERTRAIN GROUP OPTIONS 7-2 (2.2m) Deutz BF4M1013EC Engine: Deutz BF4M1013EC, 4-cylinder, turbocharged, intercooled diesel, MSHA/Tier II, 115hp 2300rpm c/w fuel filter & water separator Torque converter: Dana C2000 series Transmission: Dana 20,000 series, long drop, remote mounted, electric shift. Three forward and three reverse speeds. Vehicle speeds with 12 x rpm with standard axle ratio: 1st gear: 2.4mph (3.9kph) 2nd: 6.2mph (10kph) 3rd: 11.4mph (18.3kph) Engine end axle: New Holland D65I, no-spin differential, wet disk SAHR emergency brakes, wet disk HASR service brakes. Boom end axle: New Holland D65I, no-spin differential, wet disk SAHR emergency brakes, wet disk HASR service brakes. Drivelines: Mechanics 6C and 7C 6-5 (2.0m) 7-2 (2.2m) Caterpillar C4.4 ACERT Engine: Caterpillar C4.4 ACERT electronic 4-cylinder, turbocharged, intercooled diesel, Tier III, 127hp (95kW)@2200rpm c/w fuel filter & water separator Torque converter: Dana C2000 series Transmission: Dana 20,000 series, long drop, remote mounted, electric shift. Three forward and three reverse speeds. Vehicle speeds with 12x rpm with standard axle ratio 1st gear: 2.4mph (3.9kph) 2nd: 6.2mph (10kph) 3rd: 11.4mph (18.3kph) Engine end axle: New Holland D65I, no-spin differential, wet disk SAHR emergency brakes, wet disk HASR service brakes. Boom end axle: New Holland D65I, no-spin differential, wet disk SAHR emergency brakes, wet disk HASR service brakes. Drivelines: Mechanics 6C and 7C 6-5 (2.0m) 7-2 (2.2m) Deutz BF4M1013EC Engine: Deutz BF4M1013EC, 4-cylinder, turbocharged, intercooled Diesel, MSHA/Tier II, 154hp 2300 RPM c/w fuel filter & water separator Torque Converter: Dana C270 series Transmission: Dana 32,000 series, long drop, remote mounted, electric shift Three forward and three reverse speeds. Vehicle speeds with 12:00x rpm with standard axle ratio: 1st gear: 2.4mph (3.9kph) 2nd: 6.2mph (10.9 kph) 3rd: 11.4mph (18.3 kph) Engine end axle: New Holland D65I no spin differential wet disk SAHR emergency brakes, wet disk HASR service brakes, complete with external walking beam, +/- 8 degrees oscillation Boom end axle: New Holland D65I no spin differential wet disk SAHR emergency brakes, wet disk HASR service brakes. Drivelines: Mechanics 6C and 7C 6-6 (2.0m) 9-11 (3.0m) Deutz BF6M1013EC High Altitude High Altitude Performance Engine: Deutz BF6M1013EC, 4-cylinder, turbocharged, intercooled Diesel, MSHA/Tier II, 210hp 2300 RPM c/w fuel filter and water separator derated for altitude Torque Converter: Dana C320 series Transmission: Dana 32,000 series, long drop, remote mounted, electric shift Three forward and three reverse speeds. Vehicle speeds with 12:00x rpm with standard axle ratio: 1st gear: 2.4mph (3.9kph) 2nd: 6.2mph (10.9 kph) 3rd: 11.4mph (18.3 kph) Engine end axle: New Holland D65I no spin differential wet disk SAHR emergency brakes, wet disk HASR service brakes, complete with external walking beam, +/- 8 degrees oscillation Boom end axle: New Holland D65I no spin differential wet disk SAHR emergency brakes, wet disk HASR service brakes. Drivelines: Mechanics 6C and 7C ENG RMS SCALER BREAKER TECHNOLOGY 5

6 PROTECTIVE STRUCTURE OPTIONS SALES SPECIFICATIONS RMS SERIES 8-6 (2.6m) 12:00x20 tires 8-4 (2.5m) 10:00x20 tires ROPS/FOPS Canopy Tested & certified ROPS/FOPS canopy, c/w guard bars to help protect operator and passenger from dangerous fly-rock. Complete with swivel operator seat. 8-2 (2.5m) 12:00x20 tires 8 (2.4m) 10:00x20 tires ROPS/FOPS Cab Full cab; covers operator, controls & passenger. Tested and certified ROPS/FOPS cab, c/w guard bars to protect operator and passenger from dangerous fly-rock. Includes heavy-duty safety glass, wiper/ washers, HVAC heat / air conditioning system, air pressurization system & operator swivel seat. OPERATOR SEAT OPTIONS Swivel Suspension Seat Swivel Air Ride Seat Mine duty swivel operator seat options available in suspension and air ride variations. PASSENGER SEAT OPTIONS No passenger seat Suspension seat (facing boom) Air Ride Seat (facing boom) AIR INTAKE SYSTEM OPTIONS Air Intake Filter A dry element filter with safety element and replacement indicator. Air Intake Precleaner A dry element filter with safety element and replacement indicator, complete with a cyclone Pre-cleaner. A pre-cleaner extends the life of an air filter by removing dirt & contaminants before reaching the filter & ejecting them via the exhaust. 6 BREAKER TECHNOLOGY RMS SCALER ENG-0112

7 RMS SERIES SALES SPECIFICATIONS EXHAUST SYSTEM OPTIONS Catalytic Exhaust A catalytic exhaust, purifier/silencer. No exhaust blanket. Exhaust Manifold and Turbo Coating Prevents fluids from igniting on hot engine and exhaust parts. High temperature performance: ideal for engine compartment components requiring long-term exposure to high temperatures. Non-flammable. Protects personnel from burns. Lowers ambient temperature; cooler engine compartment, less heat stress on operators and maintenance personnel. Exhaust System Wrap Prevents fluids from igniting on exhaust parts. High temperature performance. Non-flammable. Protects personnel from burns. Lowers ambient temperature; cooler engine compartment, less heat stress on operators and maintenance personnel. FUEL TANK OPTIONS Fuel Tank 50 gallon (189 liter) fuel tank, top fill. Fuel Tank with Fast Fill 50 gallon (189 liter) fuel tank complete with Fast Fill filling system. Designed for on-site fast fluid transfer. HYDRAULIC TANK OPTIONS Hydraulic Tank 50 gallon (189 liter) hydraulic tank, top fill, 4 psi pressurized cap. Hydraulic Tank with Fast Fill 50 gallon (189 liter) hydraulic tank complete with Fast Fill filling system. Designed for on-site fast fluid transfer. FIRE SUPPRESSION SYSTEM OPTIONS No Fire Suppression System Fire Extinguisher 1 x 20 lb (9 kg) fire extinguisher Ansul Fire Suppression Ansul fire suppression system, 6 nozzle fittings, c/w 2 actuators. Includes 20 lb (9 kg) fire extinguisher. Ansul Fire Suppression with Detection Ansul fire suppression system, 6 nozzle fittings, c/w 2 actuators. Includes a check fire detection and activation system. Includes 20 lb (9 kg) fire extinguisher ENG RMS SCALER BREAKER TECHNOLOGY 7

8 ELECTRIC POWER PACK OPTIONS No Power Pack bumper SALES SPECIFICATIONS RMS SERIES 10-8 (3.3m) Power Pack Power Pack, bumper mounted 50hp (37kW) electric motor, c/w starter panel. Advise voltage at time of order. Cable reel not included. Power Pack with Cable Reel Bumper mounted, 50hp (37kW) electric auxilliary electric/hydraulic power pack. 100cc/rev pump c/w starter panel and cable reel. Cable supplied by customer. Advise voltage at time of order (3.3m) DUST SUPPRESSION SYSTEM OPTIONS No Dust Suppression System On-board System Strategically located spray nozzles suppress dust at the pick tool. Activation switch is located on the remote control box. The system uses mine water. Cannot be combined with passenger seat option and/or ROPS/FOPS cab option. TIRE OPTIONS Pneumatic Tires 12:00 x 20; 20 ply, air filled, mine lug tread Foam Filled Tires 12:00 x 20; 28 ply, foam filled WHEEL CHOCK OPTIONS No Wheel Chocks Wheel Chocks - aluminum Complete with holder 8 BREAKER TECHNOLOGY RMS SCALER ENG-0112

9 RMS SERIES SALES SPECIFICATIONS BOOM GREASING SYSTEM OPTIONS Point of use grease fittings Point of use grease fittings, no remote greasing points Boom Manual Grease System Manual greasing system, boom only. Strategically placed grease manifolds which are easily accessible by grease gun for lubricating all boom cylinders and boom pivot pins. BREAKER GREASING SYSTEM OPTIONS Boom Auto-Grease System Auto grease system, boom only. VDC grease pump with a 5 gal (19 liter) reservoir, located midship. Timer activated automatic grease injector manifolds for lubricating all boom cylinders and boom pivot points. Point of Use Point of use grease fittings, no remote greasing points Breaker Auto-Grease System Auto greasing system, breaker only, c/w 2 gal (8 liter) 24 VDC electric driven grease pump and reservoir. Pump activates when breaker is fired via remote control. Use only BTI Chisel Paste. Air Flush System Air flush system clears debris from the breaker tool chamber. DOZER BLADE OPTION No Dozer Blade Dozer Blade Dozer blade is 7 (2.2m) wide, twin 5 (127mm) hydraulic cylinders in a low profile mounting configuration. Dozer blade option used to clean fallen loose material, allowing machine to get closer to the face for the next setup ENG RMS SCALER BREAKER TECHNOLOGY 9

10 BREAKER OPTIONS SALES SPECIFICATIONS RMS SERIES BX10 BREAKER SPECIFICATIONS Energy Class: 1,000 ft-lb (1,350 joule) Blows per minute: , High Speed 450-1,000 Oil Flow required: US gal/min (45-80 l/min) Working Pressure: 1,450-2,000 psi ( bar) Operating Weight: 948 lb (430 kg) Tool Diameter: 3.1 (78 mm) Tool Weight: 69 lb (31.3 kg) 180 of Rotation 25 (630mm) 8-5 (2.6m) 25 (630mm) 10 BREAKER TECHNOLOGY RMS SCALER ENG-0112

11 RMS SERIES SALES SPECIFICATIONS NOTES: ENG RMS SCALER BREAKER TECHNOLOGY 11

12 SALES SPECIFICATIONS RMS SERIES All dimensions and specifications are subject to change without notice. 12 BREAKER TECHNOLOGY RMS SCALER ENG-0112