Type 2 Push-Through 37 Ton Log Splitter. Assembly Manual

Size: px
Start display at page:

Download "Type 2 Push-Through 37 Ton Log Splitter. Assembly Manual"

Transcription

1 Type 2 Push-Through 37 Ton Log Splitter Assembly Manual Refer to this manual for the following models: RS37PT-LF09PC-16-1 RS37PT-LF09EC-16-1 RS37PT-LF09EC-16-2 RS37PT-LF13EC-22-1 RS37PT-LF13EC-22-2 RS37PT-LF15EC-22-1 RS37PT-LF15EC-22-2

2 Welcome to RuggedMade. This manual explains how to assemble your new log splitter. Please read this manual completely before assembling your splitter. Certain components must be installed in a specific sequence. The splitter arrives in a wooden crate containing all of the components and hardware that you will need. If you purchased the optional log lift and log catcher tray kit, it will arrive in a separate crate. You will need some basic tools, hydraulic fluid, engine oil, and PTFE thread seal tape. You will also need a battery if you purchased the optional electric start kit. We recommend a high quality 12N9-4B-1 12-volt battery. This will fit in the battery tray. See detailed battery spec at the end of this manual.

3 RS-737 Hardware Guide

4 Open the crate(s). Remove everything except the beam and cylinder assembly. The crate contains the following: Wheels (2) Fenders (2) Log Cradles o No Lift Kit: (2) o With Lift Kit: (1) Hardware Kit (Stored inside support leg) o Nuts and Bolts o Wheel bearing dust caps & cotter pins Suction Hose o 16GPM Pump: 1 inch o 22GPM Pump: 1-1/4 inch High pressure hose Pump to Valve 1 ¾ inch High Pressure Hose Valve 1 to Cylinder Push Side Return Line: ¾ inch Pre-Filter: Installed in Hydraulic Tank Hydraulic Tank Tongue, Hitch Coupler for 2 Ball, and Chains (2) Support Bi-pod Leg with Locking Pin Log Lift Kit (Optional) o Log Lift Tray (Upper Half & Lower Half) with Pins (2) o Brackets (2) and Pin o Log Lift Cylinder and Pins (2) o Hoses (2) o Valve and Elbow Fittings and Male-Male Coupler Fitting o Log Catcher Tray with Pins (2) Fittings various sizes Hydraulic Cylinder Main: 5 x 30 x 3 Hydraulic Cylinder Log Lift (if equipped) Beam Slip-on 4-way Blade Engine, Engine Manual, Spark Plug Tool Electric Start Kit (Optional) o Battery Tray, Rubber Strap, Positive & Negative Wires Valve for Main Cylinder Pump Pump Mount Jaw Coupler

5 Tools & Materials Required Wrenches/Sockets: o 12mm o 13mm (short & deep socket) o 14mm o 15mm x 2 o 16mm x 2 o 18mm Medium-size Phillips-Head and straight slot Screwdrivers Allen Key: 4mm (For jaw coupler set screws) Vice-grip Pliars Needle-nose Pliars Diagonal Cutting Pliars Large Adjustable Wrench Channel Locks Rubber Mallet Knife PTFE Thread Seal Tape For NPT (National Pipe Thread) taper threads on fittings Thread Lock (Blue) Engine Oil Volume: Approx. 1 quart Specification: 10W-30 4-stroke Hydraulic Fluid Volume: 12 gal Specification: AW32 (10-weight)

6 Tongue & Bi-Pod Support Leg Start by installing the support leg on the tongue. Note orientation: leg should swing away from hitch coupler when retracted. Use one of the long bolts with a 16mm head. Do not over-tighten the bolt because it acts as a hinge, allowing the leg to swing up and down. Use a locking pin to lock the leg in the down position. Install the tongue under the beam near the blade using four bolts and nuts.

7 Fenders Install the two fenders on the hydraulic tank. Use the 4 short bolts with 13mm heads from the hardware kit.

8 Wheels Make sure the bearings (two per wheel) are greased. Remove wheel nuts from axles. Install wheels with valve stems facing out. The wheels are equipped with taper roller bearings for durability. Be careful not to push the bearings out of the wheel hubs during installation. Install one large washer over the outer bearing Tighten the castellated nut so that two notches line up with the cotter pin hole in the end of the axle. The wheel should still be able to rotate freely. Insert one cotter pin through the hole in the axle and the notches of the castellated nut. Bend the pin back so that the dust cover will fit over it. Tap the dust cap into place with a rubber mallet.

9 Frame-and-Cylinder Assembly Use an engine hoist, forklift, or other means to safely lift the beam out of the crate. Maintain a horizontal orientation. NOTE: Use caution while maneuvering beam. Never place any parts of your body under it Beam is extremely heavy! Position the hydraulic tank (with wheels installed) under the rear of the beam. Line up the holes on the mounting plate on top of the tank with the holes in the bottom of the beam. There are multiple sets of holes. This allows varying amounts of room for the operator to stand between the log lift and the hydraulic tank. Keep in mind, the farther away from the blade you install the tank, the heavier the front of the splitter will be. We recommend installing the tank using the holes closest to the front (blade end) of the splitter. For additional standing room, use the set of holes second closest to the front of the splitter. Bolt the tongue and support leg assembly to the bottom of the blade end of the beam. After the tank and tongue are bolted to the beam, lower the splitter to the ground. Make sure the support leg is locked in the down position.

10 Log Cradle Install both log cradles by passing the bolts through both cradles and the vertical web of the I-beam. If your splitter is equipped with a log lift, install the single provided log cradle opposite the log lift at the same time as installing the log lift bracket. NOTE: The bolts go through the log lift bracket, the vertical part of the I- beam, and the log cradle.

11 Log Lift The log lift can be installed on either side of the beam, depending on operator preference. [Installing the log lift on the same side as the engine is preferred by some people who operate the splitter alone. Some people operate the splitter with two people one to load logs and one to control the valves and engine. They might prefer to install the log lift on the side opposite the engine.] There are two Log Lift Brackets: one L bracket sits inside the I-beam one flat bracket mounts under the beam Install both brackets on one side of the beam. Install the single log cradle on the opposite side. The bolts pass through the beam to secure the L lift bracket and the cradle. Install the upper half of the log lift table by lining up the brackets and inserting the long hinge pin. Install the log lift cylinder by inserting the two short hinge pins. Secure all hinge pins with spring clips on both sides. Check for free movement.

12 Engine Installation Place engine on engine platform. Pump should face the rear of the splitter, away from the towing coupler. Use 4 medium sized bolts, washers, and nuts to secure the engine to the platform. IMPORTANT: CHECK OIL LEVER BEFORE OPERATING!!! Engine may ship without engine oil Add oil according to the instructions in the engine manual. Check the dipstick to make sure the engine has the correct amount of oil. Oil must be up to top of threads in filler port. Lower levels may activate the low-oil cut-off switch. Electric Start Kit Battery Tray and Spacer Plate If you purchased the electric start provision kit, install the battery tray under the engine between the platform and the beam. The two bolts that secure the engine on the beam side pass through the holes at the top of the battery tray. Install the spacer plate under the side of the engine near the wheel this will ensure the engine is level. You will need to provide a 12 volt battery. The battery tray is designed to hold a 12N9-4B-1 (See detailed spec below). Follow the instructions for your battery regarding adding electrolyte and/or distilled water and initial charging. Connect the positive and negative wires to the terminals on the battery. Do not over-tighten. Install the battery in the tray. Bend the upper tab away from the engine drain plug slightly. Secure the battery with the rubber strap provided by hooking both ends on the metal tabs on the battery tray.

13 Connect the negative (BLACK) wire to the bolt that holds the engine onto the platform. Connect the positive (RED) wire to the post on the back of the starter solenoid. Bundle the wires together and secure with the wire bracket provided and/or zip ties. NOTE: The electric start control panel is the on-off switch.

14 Jaw Coupler Tighten the set screws after the first five hours of operation. Check every 100 hours thereafter. To tighten the set screws, remove the safety panel on the pump mount. Use a 3mm allen key to tighten the four set screws in the jaw coupler. Use the pull start to gently turn the engine over so that all four set screws can be reached. Replace the protective cover when finished tightening the set screws.

15 Log Lift Valve If you purchased the log lift kit, connect the second valve to the main valve and install on the valve platform. A Male-Male coupler is included. Hydraulic Fittings Install the remaining hydraulic fittings. Note that PTFE thread tape must be used on the tapered threads of all NPT fittings. Do NOT apply tape to the JIC compression end of fittings. Wrap the tape in the correct direction so that installing the fitting will not push the tape off. Hydraulic Hoses and Fittings Install the fittings and hoses per the pictures below Hydraulic Fluid Add 12 gallons of AW32 (10-weight) hydraulic fluid. Do not top off. Cylinder will be jerky at first, but system will purge air automatically.

16 Return Line Filter (optional) If you purchased the optional return line filter, follow these assembly steps: 1. Install the provided 1-1/4 to 1-1/4 Male-Male fitting between the OUTLET port of the filter housing and the RETURN port on the hydraulic tank. The return port is welded to the side of the tank below the vented fill cap. It is not the port under the engine platform. 2. Install the 1-1/4 to ¾ Male-Female fitting on the INLET port of the filter housing. The 1-1/4 end goes in the filter housing Install a ¾ NPT elbow fitting in the Female end Connect the ¾ return hose to the compression end of the elbow 3. Install the rubber gasket in the channel under the lip of the filter housing. Apply hydraulic fluid to the gasket first Make sure the gasket is seated properly 4. Screw the filter element onto the housing until it contacts the base of the housing. Then TIGHTEN ½ TURN. 5. After adding hydraulic fluid, RUN SYSTEM and CHECK FOR LEAKS. 6. Replace filter element when replacing hydraulic fluid. Note: PTFE thread tape must be used on the tapered threads of all NPT fittings connected to the filter housing What you will receive with filter kit

17 Valve Auto-Return Detent Adjustment Your log splitter valve features an auto-return detent. The lever will stay in the retract position until the rod is fully retracted. A relief valve senses an increase in pressure when the piston reaches the end of the cylinder. This kicks the valve lever into the neutral position. The relief valve setting may need to be adjusted periodically. You will need a 22mm wrench to loosen the lock nut and a 16mm wrench to adjust the relief bolt. NOTE: Make all adjustments with the engine off and cycle the valve lever to release built-up pressure. Valve kicks off into neutral before rod is fully retracted The relief valve pressure setting is too low. Loosen the lock-nut closest to the valve. Turn the bolt clockwise ¼ turn to tighten the relief spring. Tighten the lock nut, start the engine, and test the valve. Continue making adjustments of ¼ turn until the kick-off pressure is suitable. Valve stays in retract position even after rod is fully retracted The relief valve pressure setting is too high. Loosen the lock-nut closest to the valve. Turn the bolt counter-clockwise ¼ turn to loosen the relief spring. Tighten the lock nut, start the engine, and test the valve. Continue making adjustments of ¼ turn until the kick-off pressure is suitable. NOTE: The auto-return detent relief valve sticks out from the side of the valve. There is also a main relief valve located next to the lever. Do not confuse these two. NOTE: The auto-return function increases the speed and convenience of splitting wood, but always pay attention to the position of the rod and push plate on the retract stroke. There are pinch points that can cause injury.

18 Slip-On 4-Way Blade This will split logs into four pieces. It can significantly increase splitting efficiency. Only use it with logs that are 24 inches in diameter or less. The bevel in the leading edge of the horizontal blades must always face UP.

19 Towing Use caution when transporting the splitter. It does not have a suspension, so maximum safe towing speed is 40mph on smooth roads, and lower for uneven road surfaces. Be sure to attach the safety chains, secure the log catcher and outer panel of the log lift, and lock the support leg in the upright position when towing. Check tire pressure before towing. Before towing, turn off the fuel petcock and run the engine until it stops. This will prevent fuel from passing through the carburetor and entering the crankcase of the engine.

20 RuggedMade by IMS 7 Market Street Rockland, MA Tel: RUGGED ( ) info@ruggedmade.com Website:

Please read all instructions before operation!!

Please read all instructions before operation!! 1 Flow Rate: 8gpm Pressure Range: 0-2000psi RPM: 60 (load free) Torque: 600 ft lb HP: 13 Honda Engine Features: Auxiliary Flat Faced Male and Female Quick Disconnects Ship Weight: 510 lbs Reservoir Capacity:

More information

Safety Assembly Operation Service and Adjustment Repair Parts 1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI PHONE FAX

Safety Assembly Operation Service and Adjustment Repair Parts 1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI PHONE FAX swisherinc.com OWNER S MANUAL MODEL NO. LS622 LS826 LS934 LS10534D LOG SPLITTER IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. Rev.07.04.2001 Safety

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

NORTHSTAR TRAILERS. Assembly Guide for SPORTSTAR II Trailer

NORTHSTAR TRAILERS. Assembly Guide for SPORTSTAR II Trailer NORTHSTAR TRAILERS Assembly Guide for SPORTSTAR II Trailer Congratulations! You are the proud owner of a NORTHSTAR trailer. Please follow the instructions and steps in this manual for proper assembly.

More information

NORTHSTAR TRAILERS. Assembly Guide for MULTISTAR Trailer

NORTHSTAR TRAILERS. Assembly Guide for MULTISTAR Trailer NORTHSTAR TRAILERS Assembly Guide for MULTISTAR Trailer Congratulations! You are the proud owner of a NORTHSTAR trailer. Please follow the instructions and steps in this manual for proper assembly. TRAILER

More information

NORTHSTAR TRAILERS. Assembly Guide for SPORTSTAR I Trailer

NORTHSTAR TRAILERS. Assembly Guide for SPORTSTAR I Trailer NORTHSTAR TRAILERS Assembly Guide for SPORTSTAR I Trailer Congratulations! You are the proud owner of a NORTHSTAR trailer. Please follow the instructions and steps in this manual for proper assembly. We

More information

AmTryke Adult Recumbent Model HP1000 #50-HC-1000

AmTryke Adult Recumbent Model HP1000 #50-HC-1000 AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

OPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300

OPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300 1-800-223-4540 ** 602-437-5020 OPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300 READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING MACHINE Contents Safety Instructions Pg 3 Operating Instructions Pg 4-5 (Light

More information

INFEED HOPPER COMPONENTS. Parts may not be exactly as shown. Bandit. Copyright 1/12

INFEED HOPPER COMPONENTS. Parts may not be exactly as shown. Bandit. Copyright 1/12 INFEED HOPPER COMPONENTS 80 INFEED HOPPER COMPONENTS 1. 626-200019 Folding Pan for Infeed Hopper 2 a. 900-4901-83 Folding Pan Spring Lock & Trap Door Lock b. 900-7900-93 Black Rubber Cap (Not Shown) 3

More information

VALVE AND PLUMBING KIT 2408TL LOADER AGCO & MASSEY FERGUSON TRACTORS

VALVE AND PLUMBING KIT 2408TL LOADER AGCO & MASSEY FERGUSON TRACTORS ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT 2408TL LOADER AGCO & MASSEY FERGUSON TRACTORS AGCO MASSEY FERGUSON CAB ROPS ST34A 1533 X ST41A 1540 N/A X TRACTOR AND VALVE KIT GENERAL

More information

IAG Air / Oil Separator (AOS) For STi

IAG Air / Oil Separator (AOS) For STi IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,

More information

** DO NOT EXCEED THE RECOMMENDED VEHICLE TOWING WEIGHT RATING ** DODGE RAM 1500

** DO NOT EXCEED THE RECOMMENDED VEHICLE TOWING WEIGHT RATING ** DODGE RAM 1500 10/3/2017 DODGE RAM 1500 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE

More information

Service Kit

Service Kit Service Kit 753-05607 Date: Subject: Models Affected: April 17, 2009 (Revised 6/08/2009) Hydraulic Cylinder Seal Replacement XINGHUI 4.5 Cylinder 718-0769A Read through and understand these instructions

More information

AmTryke Adult Recumbent Model JT2000 #50-FC-2000

AmTryke Adult Recumbent Model JT2000 #50-FC-2000 AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

ASSEMBLY MANUAL SMC 2491 LOADER VALVE AND PLUMBING KIT INSTRUCTIONS KUBOTA TRACTORS

ASSEMBLY MANUAL SMC 2491 LOADER VALVE AND PLUMBING KIT INSTRUCTIONS KUBOTA TRACTORS ASSEMBLY MANUAL Keep With Loader Operator's Manual SMC 2491 LOADER VALVE AND PLUMBING KIT INSTRUCTIONS KUBOTA TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB L5450 X X Valve and plumbing kit can be installed

More information

Oil pan, oil strainer and valve body, removing and installing

Oil pan, oil strainer and valve body, removing and installing Page 1 of 44 38-1 Oil pan, oil strainer and valve body, removing and installing WARNING! Do not run engine with the oil pan removed or without ATF filling and do not tow vehicle. Notes: Always replace

More information

Rollstar Shade Installation Instructions

Rollstar Shade Installation Instructions Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the

More information

SUT-250-S (These instructions are used for SUT-250-SCLC also)

SUT-250-S (These instructions are used for SUT-250-SCLC also) SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16,

More information

INSTRUCTION MANUAL ALL TERRAIN PALLET TRUCK HAND PALLET TRUCK

INSTRUCTION MANUAL ALL TERRAIN PALLET TRUCK HAND PALLET TRUCK INSTRUCTION MANUAL ALL TERRAIN PALLET TRUCK HAND PALLET TRUCK WARNING! 1. Read and understand instruction manual before using the pallet truck. 2. Do not place hands or feet under the pallet truck at any

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

SUT-450-I ASSEMBLY REQUIREMENTS

SUT-450-I ASSEMBLY REQUIREMENTS SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473.3664 F:620.869.9031 Turnoverball Gooseneck Hitch Installation Instructions

More information

Final Assembly Instructions Portside Cruiser

Final Assembly Instructions Portside Cruiser Final Assembly Instructions Portside Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert cycling

More information

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax) INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing

More information

UNPACK AND IDENTIFY THE FOLLOWING PARTS.

UNPACK AND IDENTIFY THE FOLLOWING PARTS. SUT-500-S ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first

More information

Remove the rear tire and the (8) 13mm bolts holding the tire carrier to the tailgate. Remove the 3rd brake light wiring harness.

Remove the rear tire and the (8) 13mm bolts holding the tire carrier to the tailgate. Remove the 3rd brake light wiring harness. J108781 2 4 Rear Bumper & Tire Carrier & Optional Flood Lights Jeep Wrangler JK (2007-2017) Tools Required: Basic Hand Tools 35mm Socket Tape Measure Grease Gun Straight Edge Remove the rear tire and the

More information

UNPACK AND IDENTIFY THE FOLLOWING PARTS.

UNPACK AND IDENTIFY THE FOLLOWING PARTS. SUT-350-AIT ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first

More information

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

Suzuki GS1000G fork seal replacement

Suzuki GS1000G fork seal replacement Suzuki GS1000G fork seal replacement Before you start you require: 1) To read workshop service manual for your model 2) Socket allen key M8 3) Torque wrench 4) Special tool to hold inner, make your own,

More information

ASSEMBLY MANUAL. Keep With Operator s Manual

ASSEMBLY MANUAL. Keep With Operator s Manual ASSEMBLY MANUAL Keep With Operator s Manual 2-6347 VALVE AND PLUMBING KIT INSTRUCTIONS SMC 64Q LOADER KUBOTA TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB B2150DT & B2150HSD X X B8200DT & B8200HSD X X B9200DT

More information

WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil.

WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. Things needed for assembly. -2 tubes of blue loc-tite. I don

More information

SMF / DSF / DTF SMF / DSF / DTF 200

SMF / DSF / DTF SMF / DSF / DTF 200 2006 SMF / DSF / DTF 200 1 The drawings in this parts book have been scaled so that parts can be easily recognized. 1 CYLINDER ASSY 2 CYLINDER ASSY Ref # Part # Description 1 410 0001A CYLINDER HEAD COVER

More information

Our goal is to make the install a breeze. Please read the entire guide before beginning.

Our goal is to make the install a breeze. Please read the entire guide before beginning. www.airkewld.com Page 1 of 6 IRS Axle Kit Install IRS Axle Kit Install Our goal is to make the install a breeze. Please read the entire guide before beginning. KITS SHOULD INCLUDE 2 - Control-arm mounting

More information

Page 1 of HP B&S Vanguard Engine

Page 1 of HP B&S Vanguard Engine 1405 Page 1 of 41 14 HP B&S Vanguard Engine 1405 Page 2 of 41 14 HP B&S Vanguard Engine Ref # Part Number Qty S/P/F Description BS-28Q777-0647-E1 1 14 HP B&S Vanguard Engine 1 BS-496412 1 Cylinder Assembly

More information

VALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X

VALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X TRACTOR AND VALVE KIT GENERAL

More information

Bonneville/Thruxton A.R.K. Guide

Bonneville/Thruxton A.R.K. Guide Kit Includes: 1. Hardware 2. 3M Double Sided Tape 3. Jet Kit 4. Carburetor Support Brace 5. 2 x K&N Air Filters 6. Crankcase Breather Filter Fits The Following Motorcycles: Triumph Thruxton Triumph Bonneville

More information

ASSEMBLY MANUAL VALVE AND PLUMBING KIT INSTRUCTIONS NEW HOLLAND TRACTORS WITH TANDEM GEAR PUMP HYDRAULIC SYSTEM

ASSEMBLY MANUAL VALVE AND PLUMBING KIT INSTRUCTIONS NEW HOLLAND TRACTORS WITH TANDEM GEAR PUMP HYDRAULIC SYSTEM ASSEMBLY MANUAL 715809002 BUNDLE 2-6437 Keep With Operator's Manual VALVE AND PLUMBING KIT INSTRUCTIONS NEW HOLLAND TRACTORS WITH TANDEM GEAR PUMP HYDRAULIC SYSTEM MODEL 2WD 4WD LESS CAB WITH CAB 5640,

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08

More information

Perfect Park 7000 Installation & Unloading Instructions Operating Manual

Perfect Park 7000 Installation & Unloading Instructions Operating Manual Perfect Park 7000 Installation & Unloading Instructions Operating Manual 1) Always file a claim with the truck line if the lift has been damaged! (If you don t originally notice the damage, but find some

More information

SSR200 Zongshen 200cc Dirt Bike (VIN PREVIX LZSJ)

SSR200 Zongshen 200cc Dirt Bike (VIN PREVIX LZSJ) Page 1 of 19 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > SSR200 Zongshen 200cc Dirt Bike (VIN PREVIX LZSJ) SSR200 Zongshen 200cc Dirt Bike (VIN PREVIX LZSJ) SSR200 Zongshen

More information

6280 PART NUMBERS & DIAGRAMS

6280 PART NUMBERS & DIAGRAMS EXTERNAL PARTS 112 73330 111-2D 73313 73315 6280HD-146 136 230 73242 73205 73213 162 206 207 73245 179 73020 168 178 206 73228 73221 241 73221 6280-110 Wheel Spacer (Not Shown) 6280-111-2D Wheel with Hub

More information

Mustang Shaker

Mustang Shaker 2005-2009 Mustang Shaker CDC #110050 ( 05/ 06) or 0711-7000-01 ( 07/ 09) Component Check List: Quantity/Description Part # CDC Installer 1 - Engine Cover Assembly 114050 1 - Aluminum Shaker Scoop 183020

More information

13AU609H063 (1999) Page 1 of 25 Axle & Wheels Front And Steering Assembly

13AU609H063 (1999) Page 1 of 25 Axle & Wheels Front And Steering Assembly 13AU609H063 (1999) Page 1 of 25 Axle & Wheels Front And Steering Assembly 13AU609H063 (1999) Page 2 of 25 Axle & Wheels Front And Steering Assembly 1 683-0304 1 S Frame 2 710-0604A 1 /P Self-tapping Screw,

More information

Land Cruiser FJ80 and FZJ80 Double Swingout Rear Bumper Installation Instructions PRELIMINARY

Land Cruiser FJ80 and FZJ80 Double Swingout Rear Bumper Installation Instructions PRELIMINARY Land Cruiser FJ80 and FZJ80 Double Swingout Rear Bumper Installation Instructions Fits 1991-1997 80 Series Land Cruiser / Lexus LX450 PRELIMINARY Thank you for purchasing a Rear Bumper for your Land Cruiser.

More information

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis. Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers

More information

SERVICE INSTRUCTIONS ASSEMBLY & DISASSEMBLY T50X DOUBLE ACTING HYDRAULIC SERIES ACTUATORS

SERVICE INSTRUCTIONS ASSEMBLY & DISASSEMBLY T50X DOUBLE ACTING HYDRAULIC SERIES ACTUATORS Page 1 of 7 SERVICE INSTRUCTIONS ASSEMBLY & DISASSEMBLY T50X DOUBLE ACTING HYDRAULIC SERIES ACTUATORS INTRODUCTION This service procedure is offered as a guide to enable general maintenance to be performed

More information

400 2x4/4x4 EFT SHARE OUR PASSION ṬM

400 2x4/4x4 EFT SHARE OUR PASSION ṬM SHARE OUR PASSION ṬM 400 2x4/4x4 EFT Model Number A2009IDG2BETR (Red - 2x4) Model Number A2009IDG2BETZ (Cat Green - 2x4) Model Number A2009IDG4BETR (Red - 4x4) Model Number A2009IDG4BETG (Green - 4x4)

More information

Final Assembly Instructions: Runaround Cruiser

Final Assembly Instructions: Runaround Cruiser Final Assembly Instructions: Runaround Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert

More information

B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:

B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F: B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS 66748 P:620.473.3664 F:620.473.3766 NOTE: We recommend reading instructions before beginning the installation. GM OEM Mount System Slider

More information

PARTS CATALOG ODYSSEY INCLUDES MOWER

PARTS CATALOG ODYSSEY INCLUDES MOWER PARTS CATALOG 8-3350 ODYSSEY INCLUDES MOWER INDEX PAINT ENGINES GENERAL INFO PRODUCT IDENTIFICATION NUMBERS (P.I.N.) OR SERIAL NUMBERS (S/N) ENGINE MODEL, SERIAL AND SPECIFICATION NUMBERS TRACTOR MODEL

More information

DIAMOND CONCRETE SAW PARTS LIST MODEL CC8000 P R O D U C T S. (Revised )

DIAMOND CONCRETE SAW PARTS LIST MODEL CC8000 P R O D U C T S. (Revised ) DIAMOND P R O D U C T S CONCRETE SAW PARTS LIST MODEL CC8000 (Revised 10-15-2002) Table of Contents Page Saw Controls Legend. 3 Drawing 1. Frame Group. 4-5 Drawing 2. Arm Assembly... 6-7 Drawing 3. Hydraulics

More information

LPE C5 Battery Relocation Kit

LPE C5 Battery Relocation Kit LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction

More information

2800 VIBRO-TILL FIELD CULTIVATOR ASSEMBLY INSTRUCTIONS Series. Kongskilde

2800 VIBRO-TILL FIELD CULTIVATOR ASSEMBLY INSTRUCTIONS Series. Kongskilde 2800 VIBRO-TILL FIELD CULTIVATOR Kongskilde 2800 Series *Model may not be exactly as shown. Kongskilde reserves the right to make changes to product designs and specifications without notice or obligation

More information

S/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly

S/N 1H019H - 1H310H Page 1 of 33 46 Cutting Deck Assembly 1180 S/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly 1180 S/N 1H019H - 1H310H Page 2 of 33 46" Cutting Deck Assembly 1 17982 1 S Reinforcement Spindle Plate 2 618-0430 1 S Spindle Assembly w/

More information

ASSEMBLY MANUAL. 45-Foot Air Double Disc Drill. Amity Technology, LLC th Avenue North Fargo, ND (701)

ASSEMBLY MANUAL. 45-Foot Air Double Disc Drill. Amity Technology, LLC th Avenue North Fargo, ND (701) ASSEMBLY MANUAL 45-Foot Air Double Disc Drill Amity Technology, LLC 2800 7th Avenue North Fargo, ND 58102 (701) 232-4199 www.amitytech.com TABLE OF CONTENTS Main Frame 1 Wing Lock Towers 3 Wing Frames

More information

1. Seat 6. Side cover 11. Fuel pump retainer. 4. Mud guard 9. Fuel pump gasket : Do not reuse.

1. Seat 6. Side cover 11. Fuel pump retainer. 4. Mud guard 9. Fuel pump gasket : Do not reuse. LT-A450** K8 ~ L0 LT-A500** K9 ~ L1 LT-A750** K8 ~ L1 Fuel Tank Removal, Inspection and Installation Procedure Necessary Tools Ratchet handle (9.5 sq) Socket wrench (10 mm, 9.5 sq) Socket wrench (12 mm,

More information

Part Number: 2073T000 PARTS MANUAL. Serial Number & up WXR740/L. Trailer Wood Splitter

Part Number: 2073T000 PARTS MANUAL. Serial Number & up WXR740/L. Trailer Wood Splitter PARTS MANUAL Serial Number 000 & up Trailer Wood Splitter Foreword This Wallenstein parts manual is prepared to assist customers in ordering quality OEM replacement parts. Regular maintenance combined

More information

Model ET 5000W Operation and Service Manual

Model ET 5000W Operation and Service Manual Model ET 5000W Operation and Service Manual Patented 5/16 BALL Load Capacity: 5000 lbs The ET 5000W ESCALATE TRAILER offers ground level roll-on loading and roll-off unloading of equipment with non-tilting

More information

WX540-LEU Trailer Log Splitter Parts Manual

WX540-LEU Trailer Log Splitter Parts Manual EMB Manufacturing Inc. Boomer Line St. Clements, On N0B M0 Canada Ph: (59) 99-98 Fax: (59) 99- www.embmfg.com WX50-LEU Trailer Log Splitter Parts Manual S/N E9USXDS000 & After Refer to the operators manual

More information

90 Utility Model Number A2013KUB2BUSZ SHARE OUR PASSION.

90 Utility Model Number A2013KUB2BUSZ SHARE OUR PASSION. 2013 90 Utility Model Number A2013KUB2BUSZ TM SHARE OUR PASSION. TABLE OF CONTENTS 2013 ATV 90 (Model No. A2013KUB2BUSZ) BODY PANEL AND HEADLIGHT ASSEMBLY... 1 FRONT AND REAR RACK ASSEMBLY... 2 FRAME AND

More information

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS

More information

235/245400, , 28N

235/245400, , 28N Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters

More information

Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.

Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings

More information

Sherco Setup and Lubrication Guide

Sherco Setup and Lubrication Guide Sherco Setup and This guide is designed to provide the Sherco owner with instructions on how to: Set up a new bike Clean and re-oil the air filter Change the transmission oil Change the fork oil Repack

More information

40 Plug Aerator Model# AE-40T

40 Plug Aerator Model# AE-40T 40 Plug Aerator Model# AE-40T 11122010 Pre-assembly Instructions: For best results, follow all directions step by step. Read entire step instructions first, and then proceed with the set up. Open all boxes

More information

UNPACK AND IDENTIFY THE FOLLOWING PARTS.

UNPACK AND IDENTIFY THE FOLLOWING PARTS. SUT-250-M2 ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first

More information

Parts Manual for the Wright Z

Parts Manual for the Wright Z Parts Manual for the Wright Z Serial numbers 40581 & Higher Check www.wrightmfg.com for the latest revision Rev 9/2007 Shown with OPTIONAL Grass Collection System 2006 Wright Manufacturing Inc., All Rights

More information

A B C D E F. Tools Required (supplied by others)

A B C D E F. Tools Required (supplied by others) Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)

More information

MAZDASPEED3 Intercooler Instructions

MAZDASPEED3 Intercooler Instructions MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through

More information

L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT

L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT 6/15/2016 #1050311D 2010-12 6.7 Dodge Cummins FlowMAX Lift Pump Kit (I-00329) - 1-2010-12 6.7L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT Installation Instructions P/N # 1050311D PLEASE READ ALL INSTRUCTIONS

More information

RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.

RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS. RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR 2007-2016 JEEP WRANGLER ALL MODELS. Rear Bumper Installation Instructions 1) Remove factory rear bumper, (this includes all tow hitch

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F: B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 6678 P:620.73.366 F:620.869.903 RAM OEM Mount System Installation Instructions 25,000 LBS.

More information

C44090 HP325 PACBRAKE COMPRESSOR CONVERSION

C44090 HP325 PACBRAKE COMPRESSOR CONVERSION C44090 HP325 PACBRAKE COMPRESSOR CONVERSION APPLICATIONS: DODGE 2003-2007 5.9L CUMMINS Compressor Replacement Instructions for C14030, C14045, C44030, C44045, C44049 & C44052 with Air Tank KIT CONTENTS

More information

BEFORE BEGINNING INSTALLATION

BEFORE BEGINNING INSTALLATION COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations

More information

Mulching and Finishing Mowers MP and FP

Mulching and Finishing Mowers MP and FP Mulching and Finishing Mowers MP and FP Parts Manual Locke Turf 0 Highway E, Opp, Alabama, () -00 Transport Wheel, Tire & Spindle MP and FP ALPHABETICAL INDEX CONTENTS PAGE 00 Hydraulic Cylinder (Rear)

More information

INSTALLATION AND USER MANUAL

INSTALLATION AND USER MANUAL INSTALLATION AND USER MANUAL SDKIT-730 & SDKIT-734 100% Bolt-On 150 PSI Train Horn System for 2011-2015 F-250 & F-350 Super Duty P/N SDKIT-730 P/N SDKIT-734 Thank you for purchasing a Kleinn Air Horns

More information

WX540-LEU Trailer Log Splitter Parts Manual

WX540-LEU Trailer Log Splitter Parts Manual EMB Manufacturing Inc. Boomer Line St. Clements, On N0B M0 Canada Ph: (9) 99-98 Fax: (9) 99- www.embmfg.com WX0-LEU Trailer Log Splitter Parts Manual S/N E9USES00 & After Refer to the operators manual

More information

Parts Manual for the Wright Z

Parts Manual for the Wright Z Parts Manual for the Wright Z Serial numbers 40581 & Higher Check www.wrightmfg.com for the latest revision Rev 6/2010 Shown with OPTIONAL Grass Collection System 2010 Wright Manufacturing Inc., All Rights

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

VALVE AND PLUMBING KIT 2409 LOADER CUB CADET & KIOTI TRACTORS

VALVE AND PLUMBING KIT 2409 LOADER CUB CADET & KIOTI TRACTORS ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT 2409 LOADER CUB CADET & KIOTI TRACTORS TRACTOR MODELS CUB CADET 8404, 8454 KIOTI DK45, DK50 ROPS X X TRACTOR AND VALVE KIT GENERAL INFORMATION

More information

Return to Instruction Sheet index TCI Torqueflite Trans-Scat Kit

Return to Instruction Sheet index TCI Torqueflite Trans-Scat Kit Page 1 of 11 Return to Instruction Sheet index TCI 220000 Torqueflite Trans-Scat Kit This kit can be installed in a few hours by carefully following directions. Read all instructions first to familiarize

More information

14A6816H190 GT-2150 (2003) Page 1 of 28 Carburetor

14A6816H190 GT-2150 (2003) Page 1 of 28 Carburetor 14A6816H190 GT-2150 (2003) Page 1 of 28 Carburetor 14A6816H190 GT-2150 (2003) Page 2 of 28 Carburetor TC-640221 1 /P Carburetor (Incl 184 of Engine Parts Lists) 1 TC-640216 1 Throttle Shaft & Lever Assembly

More information

PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION

PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION INSTALLATION INSTRUCTIONS PART NUMBER: L0SXC000 DESCRIPTION: 09 ASCENT TRAILER HITCH PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION SAFETY PRECAUTION: When installing Trailer Hitch,

More information

MAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS

MAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent

More information

FlexJet - Flex Cable Replacement

FlexJet - Flex Cable Replacement P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer

More information

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS.

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS. TITAN pt. no.: 02 0000 0209 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS Gen6 Extended Capacity Replacement

More information

Solar Dolly. Assembly Manual

Solar Dolly. Assembly Manual Solar Dolly Assembly Manual Components and Hardware 5 5 4 4 7 7 6. 1. Battery Box 2. Stabilizer Legs (R,L) 3. Uprights (R, L) 4. Adjustable Angle Brackets 5. Panel Brackets (R,L) 6. Controller Mounting

More information

First, check and record the camber and caster readings, they will be adjusted later.

First, check and record the camber and caster readings, they will be adjusted later. First, check and record the camber and caster readings, they will be adjusted later. The caliper-mounting bosses are machined perpendicular to the spindle so they are an excellent place for the level.

More information

EZ Build Assembly and Installation

EZ Build Assembly and Installation Form No. 1-1108 April 2014 EZ Build Assembly and Installation 41125 Drive Pro 5.0-6.8 Plow with E-72 12V Hydraulic Unit and 41175 Drive Pro 6.8-7.6 Plow with E-72 12V Hydraulic Unit Meyer Products LLC

More information

Corken Compressor Repair

Corken Compressor Repair Corken Compressor Repair Click photo to make move Gauge Openings Inspection plate with model and serial #s Oil filter and oil pump assembly Crankcase breather vent Crankcase breather location. If excess

More information

WARNING!! C-659 SUBKIT FIGURE 4

WARNING!! C-659 SUBKIT FIGURE 4 '0-'0 DODGE / TON TRUCKS '03-' DODGE 3/ & TON TRUCKS (WILL FIT /, 3/ & TON MEGA CAB SHORT BED) WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR

More information

Subaru 5-Speed Double Adjustable Short Throw Shifter

Subaru 5-Speed Double Adjustable Short Throw Shifter Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw

More information

TransLift TL 2550K Parts Manual

TransLift TL 2550K Parts Manual TransLift TL 2550K Parts Manual Tink, I nc. 2361 D urham Dayton H w y D urham, C A 95938 Toll Free 888-367-8465 Fax 530-895-0751 w w w.tink inc.co ṁ Table of Contents Full Assembly View... 2 Tank View...

More information

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake

More information

MODELS 1324 & 1624 & 1824

MODELS 1324 & 1624 & 1824 THE MODELS 1324 & 1624 & 1824 HYDRAULIC TRENCHERS CONGRATULATIONS! You are now the proud owner of a BARRETO trencher. Please take a moment of your time to look over the following information. Familiarize

More information

Parts List See cover Page

Parts List See cover Page Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let

More information

Next, set the bar level and tighten it down. Do this on both the driver and passenger sides.

Next, set the bar level and tighten it down. Do this on both the driver and passenger sides. Next, set the bar level and tighten it down. Do this on both the driver and passenger sides. Using two tape measures, measure the outside width at the front and the rear of the tubes. The front dimension

More information

Bow Extension Cylinders

Bow Extension Cylinders Bow Extension Cylinders Level of difficulty: Fairly easy to intermediate very rewarding! Requires some patience. Tools needed: - 5-mm Allen wrench or socket (only for 90-95 models) - Needle nose pliers

More information

OUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS)

OUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS) 80052 March 6, 1995 OUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS) ITEM STOCK DESCRIPTION QTY. 51 15759 LIFT UNIT (E-47H) 1 52 817000 020 10" CYLINDER 2 53 15370

More information