PLATINUM PRO PLUG-IN Nissan Z32 300ZX

Size: px
Start display at page:

Download "PLATINUM PRO PLUG-IN Nissan Z32 300ZX"

Transcription

1 PLATINUM PRO PLUG-IN Nissan Z32 300ZX (HT ) QUICK START GUIDE

2 LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System to be free from defects in material or workmanship for a period of 12 months from the date of purchase. Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service. Lockin Pty Ltd trading as Haltech suggests that the purchaser retain the dealer s dated bill of sale as evidence of the date of retail purchase. If the Haltech TM Programmable Fuel Injection System is found to be defective as mentioned above, it will be replaced or repaired if returned prepaid along with proof of purchase. This shall constitute the sole liability of Lockin Pty Ltd trading as Haltech. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representations, either expressed or implied, including any implied warranty of merchantability or fitness. In no event shall Lockin Pty Ltd trading as Haltech, be liable for special or consequential damages. DISCLAIMER Haltech will not be held responsible for any damage caused by the incorrect installation or tuning of this product. It is the installers responsibility to ensure the wiring connections and pinouts match that of the vehicle the unit is being installed into. Haltech has taken all care to make sure the connections match the specified vehicles listed, but variations in wiring and connections on vehicles can occur and therefore this should be checked BEFORE the unit is installed. Haltech highly recommends installation and tuning of this product is to be carried out by a professional, with an understanding on installing and tuning engine management systems. Misuse of this product can destroy your engine. WARNING HALTECH OFF-ROAD USAGE POLICY It is unlawful to tamper with your vehicle's emissions equipment. This ECU is designed and sold for Sanctioned Offroad/Competition Non-Emissions Controlled Vehicles only. Using this product for street / road use on public highways is prohibited by law. It is the responsibility of the installer and/or user of this product to ensure compliance with all applicable local and federal laws and regulations. Please check with your local vehicle authority before using this product. GENERAL INSTALLATION WARNING Avoid open sparks, flames or operation of electrical devices near flammable substances. Always disconnect the battery cables when doing electrical work on your vehicle. Do not charge the battery with a 24 Volt truck charger or reverse the polarity of the battery or any charging unit. Do not charge the battery with the engine running as this could expose the ECU to an unregulated power supply that could destroy the ECU and other electrical equipment. All fuel system components and wiring should be mounted away from heat sources, shielded if necessary and well ventilated. Disconnect the Haltech ECU from the electrical system whenever doing any arc welding on the vehicle by unplugging the wiring harness connector from the ECU. After completing the installation, make sure that there are no fuel leaks, and no wiring left un-insulated in case a spark or short-circuit occurs and causes a fire. Also make sure that you follow all proper workshop safety procedures. If you're working underneath a jacked-up car, always use safety stands!

3 PLATINUM Pro Plug-in Nissan Z32 / 300ZX Quick Start Guide Congratulations on purchasing a Haltech Engine Management System. This fully programmable Plug and Play product opens the door to virtually limitless performance modification and tuning of your vehicle. Programmable systems allow you to extract all the performance from your engine by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions. This quick start guide will walk you through installation of the Platinum Pro ECU into a vehicle. This guide is accompanied by the full service manual located on the software CD provided with the ECU that you or your tuner will need to refer to before completing your installation and configuration. Supported Vehicles The Platinum Pro Plug-in Nissan Z32 / 300ZX ECU supports the following: Nissan Z32 / 300ZX Platinum Pro Plug-in Nissan Z32 / 300ZX Kit Includes Haltech Platinum Pro Plug-in ECU USB Cable Software CD Quick Start Guide Loaded Basemap Your Platinum Pro Plug-in has been programmed with a basemap to suit a Nissan Z32 / 300ZX running a VG30DETT engine using a standard MAF sensor. Alternatively, a basemap using the Haltech ECU Internal MAP Sensor as a load reference is available in the following folder for you to upload into your ECU: C:\Users\<username>\Documents\Haltech\ECUMaps\Nissan\Z32 If you choose this basemap, then please make sure you connect the Haltech ECU Internal MAP sensor to the intake manifold prior to starting the vehicle. Please ensure you load, modify and check the corresponding basemap for your application before attempting to start the vehicle.

4 ECU Installation To install your new Platinum Pro Plug-in to your Nissan Z32 / 300ZX, please follow the procedures below. You will require the following tools Screwdrivers Phillips No 2, Small Flat Socket set with 10mm socket Cable Ties / 3M Velcro tape or similar 1. Locate your factory ECU. This will be located in the foot well of the passenger side of the vehicle. To access, pull back the carpet and unscrew the four 10mm bolts securing the cover in place. Remove the cover to access the ECU. Figure 1 Left hand footwell showing ECU cover Figure 2 Factory ECU Mounting Location with cover removed

5 2. With the ignition turned off remove the 3 x 10mm bolts mounting the ECU to the vehicle. Proceed to remove the bolt in the centre of the ECU connector using a 10mm socket and gently ease the connector out. Be sure to pull the connector out squarely so as not to cause any damage to the pins or wires. With the connector disconnected the ECU can be removed from the vehicle. Figure 3 Mounting Bolt Locations 3. Remove the 4 screws securing the mounting bracket to the factory ECU. Attach this bracket to the Haltech ECU as shown in figure 4 below using cable ties and 3M tape. Re install into vehicle. Figure 4 Platinum Pro Plug-in ECU mounted in factory location

6 4. (Optional) If the OEM Air Flow Meter has been removed, then the internal MAP sensor is required as the main load sensor. Please connect the internal MAP sensor to the manifold with vacuum line. This is best achieved by obtaining a T piece and connecting between the fuel pressure regulator and the manifold. Please see pictures below Figure 5 T piece installation location Figure 6 Internal MAP sensor vacuum line installed

7 5. With the ECU installed do not attempt to start the vehicle. You will need to configure the ECU. The ECU is pre-configured for use with a VG30DETT standard engine. If this is your setup then you will not have to load a basemap. However, it is still strongly recommended that you check your settings before starting your engine. With the corresponding basemap loaded into the ECU, a standard engine should be able to be started at this point. If your engine is not standard please adjust any configuration settings affected according to your setup. Figure 7 Haltech ECU Manager Software 6. With the engine started and running its time to tune. This is best achieved by your nearest engine tuner. See the listing of Haltech dealers on our website to find the one closest to you. Figure 8 Haltech ECU Manager Software tuning page

8 ECU Manager Software ECU Manager software is used for setup, calibration and diagnostics and can be found on the CD supplied with this unit or downloaded from the Haltech website. Minimum System Requirements Operating System: Windows 2000 SP4 / XP / Vista / Windows 7 Processor Speed: 1GHz RAM: 256 Mb Video Card: 128MB graphics card with 3D acceleration USB: 1.1 Hard Drive Space: 250Mb Minimum Screen Resolution: 1024 x 768 pixels Installing ECU Manager Installing ECU Manager onto your PC is performed similar to any other Windows software package. Installation is outlined below to ensure correct installation: 1.Insert the CD-ROM into your PC s CD-ROM drive. The CD should automatically launch into the Haltech Browser. If the CD does not run automatically double click on the My Computer icon on the desktop, double click on the Haltech icon (CD- ROM drive) to start the browser software. 2.The Browser will display the disclaimer and you will need to agree to the terms stated before allowing to progress. Read the Disclaimer and click on AGREE if you agree. 3.Now you will be able to access all the information contained on the CD 4.To download the Platinum Software, click on the Platinum Series ECU Manager Link. You will be prompted to install the software. Click Install to install ECU Manager and the Data Log viewer. 5. Follow the software prompts and install the software. With your programming cable (USB) attached to your ECU and the other end connected to your laptop, power up the ECU by turning your key to IGN. Start the programming software on your PC and go online with the ECU.

9 ECU Manager / ECU Manuals Detailed manuals can be found in the software by pressing your F1 key or by selecting the Help tab located at the top left of the screen ECU Manager File Extensions When ECU manager saves the map from the Haltech ECU, it saves the map with a Haltech specific file extension. The File extension can be broken down as follows: Example File : xxxx.hz Later map versions cannot be loaded into ECU's with earlier firmware versions. ECU Manager will upgrade earlier map versions when loading into ECU's with later firmware versions. ECU Manager upgrades maps between versions where equivalent settings are available. However, new settings not in the original map, will be substituted with values from the new version's default map. WHENEVER ECU MANAGER CONVERTS YOUR ECU MAP, YOU SHOULD ALWAYS CHECK YOUR MAP SETTINGS TO ENSURE THAT ALL THE APPROPRIATE SETTINGS HAVE BEEN CONVERTED CORRECTLY.

10 Rear Auxiliary Connector The Platinum Pro Plugin Series allows further expansion of your ECU by the Rear Auxiliary Connector. The Rear Auxiliary connector allows you access to: 1 Additional Digital Pulsed Input ( DPI ) 2 Additional Digital Pulsed Outputs ( DPO ) 2 Additional Digital Switched Outputs ( DSO ) 4 Additional Analogue Voltage Inputs ( AVI ) 2 Additional +13.8V Sensor Power Outputs (Limited to 500mA Per output pin) 2 Additional +5V Sensor Power Output (Limited to 50mA Per output pin) Additional Sensor Power and Signal Grounds These extra Inputs / Outputs can be used to: Fit additional sensors. (eg MAP,Temperature and Flex Fuel ) Control additional devices via relays Control additional solenoids directly (eg Aftermarket Boost Control solenoid) The Rear Auxiliary harness is available as an optional extra. ( HT ) Pin # Wire Colour Connection 1 O +5V (50mA Max) 2 Y AVI1 (MAP) 3 O/B AVI2 4 B/W SIGNAL GROUND 5 V/B DPO1 6 V/BR DPO2 7 GY<SHD> DPI1 8 R +13.8V (500mA Max) 9 O +5V (50mA Max) 10 GY AVI 3 11 GY/B AVI 4 12 B/W SIGNAL GROUND 13 V/R DSO1 14 V/O DSO R +13.8V (500mA Max) <SHD> Denotes shielded cable Figure 8 - Rear Auxiliary Harness Connector and Pinout

11 Digital Pulsed Outputs ( DPO ) Digital Pulsed Outputs are capable of producing pulsed waveforms with varying duty and frequency. DPO's can be used to control various devices such as thermo-fans, shift lights, bypass air control valves, boost control solenoids etc. When a Digital Pulsed output is activated by the ECU the output will switch to ground. Solenoid valves and shift lights etc can be run directly from the output, however high current devices such as thermo-fans and additional fuel pumps must be activated through a relay. This way the DPO is only switching a relay and not a high current draw device. Two additional outputs can be connected using the Optional Rear Auxiliary Harness ( HT ) Digital Pulsed Outputs are limited to 800mA Max current draw. Digital Switched Outputs ( DSO ) Digital Switched Outputs are capable of switching to ground DSO's can be used to control relays in an on / off state only. Two additional outputs can be connected using the Optional Rear Auxiliary Harness ( HT ) Digital Switched Outputs are limited to 800mA Max current draw. Analogue Voltage Inputs ( AVI ) Analogue Voltage Inputs accept variable voltage inputs from 0V to 5V. These inputs can also accept switch inputs that change between two different voltage levels. The On Voltage and Off Voltage define what the thresholds are between the On and Off states. The Voltage can be viewed as a channel in the software to determine the thresholds for a switched input. Two additional sensors or switched inputs can be connected using the Optional Rear Auxiliary Harness ( HT ) Analogue Temperature Inputs ( ATI ) Analogue Temperature Inputs accept variable resistance sensors. These inputs have a pull up resistor connected to them to allow them to be used with most automotive temperature senders ( Variable resistance thermistor types ). Two additional sensors can be connected using the Optional Rear Auxiliary Harness ( HT ) Wire connections When using crimp connectors ensure that the correct crimping tool is used if in doubt do a pull test on a crimp connector, the wire should break before the wire pulls out of the crimp. Terminal soldering can weaken a connection and should only be used as a last resort. If solder joints are used, ensure joints are well isolated from movement as solder joints are prone to fracture. When splicing 2 wires it is preferable to use a crimp splice again if using a solder joint, ensure joint is limited in its range of possible movement as solder joints are prone to fracture. Always use heat-shrink sleeving to insulate wires.

12 The Haltech CAN Network The Haltech CAN network allows for simple and effective expansion in ECU capability and functionality without having to go to the trouble of wiring in a whole new computer. Expansion is made possible by the addition of multiple expansion devices that communicate to the main ECU via a Control Area Network (CAN). Installation time and costs are kept to a minimum as all expansion devices are powered up from the main ECU via the pre-terminated connection cable that comes with each expansion device. Simply connect the device directly to the 8 pin CAN connector on the rear of the ECU or connect using an optional Haltech CAN Hub (order as part # HT ) if multiple expansion devices are required). Each expansion device is pre-programmed with a unique ID code which allows it to be recognised on the network and work correctly first time every time. Figure 9 Haltech ECU connected to a Racepak Dash Figure 10 Haltech ECU connected to 5 Auxiliary CAN based devices

13 ECU Pinout Figure 11 Platinum Pro Plugin Z32 / 300ZX ECU Pinout Discover other performance engine management systems on our website.

PLATINUM PRO PLUG-IN Nissan Z32 300ZX

PLATINUM PRO PLUG-IN Nissan Z32 300ZX PLATINUM PRO PLUG-IN Nissan Z32 300ZX (HT-055107) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the

More information

PLATINUM PRO PLUG-IN HONDA CIVIC (EP3)

PLATINUM PRO PLUG-IN HONDA CIVIC (EP3) PLATINUM PRO PLUG-IN HONDA CIVIC (EP3) 2002-2005 (HT055047) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com

More information

PLATINUM SPORT GM (HT051100) QUICK START GUIDE. Version

PLATINUM SPORT GM (HT051100) QUICK START GUIDE.   Version PLATINUM SPORT GM (HT051100) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the Haltech Website for

More information

PLATINUM. Sport Haltech 13B Terminated Engine Harness QUICK START GUIDE

PLATINUM. Sport Haltech 13B Terminated Engine Harness QUICK START GUIDE PLATINUM Sport 1000 Haltech 13B Terminated Engine Harness QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com

More information

PLATINUM Sport Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE

PLATINUM Sport Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE PLATINUM Sport 2000 Haltech GM LS1 / LS6 Terminated Engine Harness (HT045650) QUICK START GUIDE LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the Haltech TM Programmable Fuel Injection System

More information

PLATINUM SERIES. Haltech. High Power Igniter Module QUICK START GUIDE. 4 Channel - # HT Channel - # HT Channel - # HT020040

PLATINUM SERIES. Haltech. High Power Igniter Module QUICK START GUIDE. 4 Channel - # HT Channel - # HT Channel - # HT020040 PLATINUM SERIES Haltech High Power Igniter Module QUICK START GUIDE 4 Channel - # HT020032 6 Channel - # HT020036 8 Channel - # HT020040 HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL:

More information

PLATINUM Series Haltech

PLATINUM Series Haltech PLATINUM Series Haltech Thermocouple Amplifier TCA 2 (HT059920 / HT059921) ( A / B ) TCA 4 (HT059940 / HT059921) ( A / B ) QUICK START GUIDE LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants

More information

PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 QUICK START GUIDE (HT & HT059980) Version 4

PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 QUICK START GUIDE (HT & HT059980)   Version 4 PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 (HT059970 & HT059980) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH:

More information

ELITE 1000/1500 Dodge SRT QUICK START GUIDE HT

ELITE 1000/1500 Dodge SRT QUICK START GUIDE HT E N G I N E M A N A G E M E N T S Y S T E M S ELITE 1000/1500 Dodge SRT4 03-05 QUICK START GUIDE HT-140940 LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the HaltechTM Programmable Fuel Injection

More information

MaxxECU quickstart guide ( )

MaxxECU quickstart guide ( ) Be a tuning mastermind. Like us. MaxxECU quickstart guide (2019-02-01) Online help! maxxecu.com/support Wiring diagrams Installation help Pinout Support maxxecu.com/support Legal disclaimer All performance

More information

MSD Boost Control Module PN 7763

MSD Boost Control Module PN 7763 MSD Boost Control Module PN 7763 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

MSD Boost Control Module PN 77631

MSD Boost Control Module PN 77631 MSD Boost Control Module PN 77631 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD

More information

USER GUIDE 1 USER GUIDE

USER GUIDE 1 USER GUIDE USER GUIDE 1 USER GUIDE 1 TABLE OF CONTENTS IN THE BOX...3 NAVIGATING THE MENUS...3 MENU LAYOUT...3 UPDATE YOUR PROGRAMMER...4 CONNECT WITH THE MOTORCYCLE...5 TUNE YOUR MOTORCYCLE...6 ADDITIONAL FEATURES...8

More information

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink.

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink. Quick Start Guide This is only a quick start guide. A full wiring and installation manual is included in PCLink. Installer I/O Table Wire Description Installer Connection Typical Application Trigger 1

More information

PLATINUM SPORT 1000/2000 QUICK START GUIDE. Version

PLATINUM SPORT 1000/2000 QUICK START GUIDE.   Version PLATIUM SPORT 1000/2000 QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the Haltech Website for your

More information

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink.

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink. Quick Start Guide This is only a quick start guide. A full wiring and installation manual is included in PCLink. Installer I/O Table Wire Description Installer Connection Typical Application Trigger 1

More information

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with

More information

MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012

MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012 MSD 6LS-2 Ignition Controller for Carbureted and EFI LS 2/LS 7 Engines PN 6012 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty

More information

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011

MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 MSD 6-Mod Controller for Carbureted and EFI Gen III Engines PN 6011 Parts Included 1 - Ignition Controller, PN 6011 1 - Pro-Data+ Software CD 1 - Harness 1 - Parts Bag 1-2-Bar MAP Sensor Optional Accessories

More information

MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013

MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013 MSD 6-Hemi Controller for Carbureted and EFI Hemi Engines PN 6013 Parts Included: 1 - Ignition Controller, PN 6013 1 - Pro-Data+ Software CD 1 - Parts Bag 1 - Mounting Template Optional Accessories: Hand

More information

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink.

Quick Start Guide. This is only a quick start guide. A full wiring and installation manual is included in PCLink. Quick Start Guide This is only a quick start guide. A full wiring and installation manual is included in PCLink. Installer I/O Table Wire Description Installer Connection Typical Application +14V Bat Full

More information

MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010

MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 MSD LS-1/LS-6 Controller for Carbureted and EFI Gen III Engines PN 6010 Parts Included 1 Ignition Controller, PN 6010 1 Pro-Data+ Software CD 1 Harness 1 Parts Bag 6 Timing Modules Optional Accessories

More information

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219

MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 INSTALLATION INSTRUCTIONS MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 Parts Included: 1 - Ignition 1 - Wiring Harness 1 - Parts Bag 1 - CD ROM WARNING: When installing the SB6, disconnect

More information

Lingenfelter ECSS-001 Ethanol Content Sensor Signal Simulator Installation & Operating Instructions

Lingenfelter ECSS-001 Ethanol Content Sensor Signal Simulator Installation & Operating Instructions Lingenfelter ECSS-001 Ethanol Content Sensor Signal Simulator Installation & Operating Instructions PN: L460350085 Revision - 1.6 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733

More information

MSD Single Cylinder Programmable Ignition PN 4217

MSD Single Cylinder Programmable Ignition PN 4217 MSD Single Cylinder Programmable Ignition PN 4217 Parts Included: 1 - PN 4217 1 - PN 4217 Wire Harness 1 - CD Rom 9609 1 - Parts Bag 1 - Serial Cable WARNING: During installation, disconnect the battery

More information

MSD Circle Track LS Ignition Control PN 6014CT

MSD Circle Track LS Ignition Control PN 6014CT MSD Circle Track LS Ignition Control PN 6014CT ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and

More information

Stratified Aux fuel system ecoboost 2.0

Stratified Aux fuel system ecoboost 2.0 Stratified Aux fuel system ecoboost 2.0 Additional Fuel Injection System Installation and User Guide Stratified Aux Fuel System Installation and User Guide -1-0204-0021.1 Thank you and congratulations

More information

MSD Programmable Shift Controller PN 7559

MSD Programmable Shift Controller PN 7559 MSD Programmable Shift Controller PN 7559 WARNING: During installation, disconnect the battery cables. When Disconnecting, always remove the Negative cable first and install it last. Parts Included: 1

More information

Stratified Aux fuel system ecoboost 2.0/2.3

Stratified Aux fuel system ecoboost 2.0/2.3 Stratified Aux fuel system ecoboost 2.0/2.3 4-Port Fuel Injection System Installation and User Guide Stratified 4-Port Aux Fuel System Installation and User Guide -1-0204-0024.1 Thank you and congratulations

More information

Electronic Over-Boost Protection System With Vent-to-Atmosphere Valve Control And 4 Bar Map Sensor Output Installation and User Guide

Electronic Over-Boost Protection System With Vent-to-Atmosphere Valve Control And 4 Bar Map Sensor Output Installation and User Guide Stratified guardian angel v3 Electronic Over-Boost Protection System With Vent-to-Atmosphere Valve Control And 4 Bar Map Sensor Output Installation and User Guide Guardian Angel V3 Installation and User

More information

INSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE

INSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE INSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE 2650-1846-77 Rev. B Details: Temperature Rating: -40 C to 85 C/-40 F to 185 F Vibration Specification: 20 g continuous, 50 g shock Inputs: o 4 EGT

More information

Mazda RX-7 Series 6-7

Mazda RX-7 Series 6-7 Mazda RX-7 Series 6-7 Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others.

More information

HOW TO INSTALL YOUR BOV

HOW TO INSTALL YOUR BOV Product Name: BOV Smart SP Supersonic 2015+ 2.7/3.5 F150/Raptor Ecoboost Product Description: 2015+ 2.7/3.5L Ford Ecoboost OEM Replacement BOV Product Number: TS-0215-1371 ------------------------------------------------------------------------------------------------------------------------

More information

Link G4 Plug-In ECU. Mitsubishi VR4 4G63-t. G4 Plug-In Installation and Configuration Manual. Mitsubishi VR4 4G63-t. Copyright 2010 Link

Link G4 Plug-In ECU. Mitsubishi VR4 4G63-t. G4 Plug-In Installation and Configuration Manual. Mitsubishi VR4 4G63-t. Copyright 2010 Link Link G4 Plug-In ECU Mitsubishi VR4 4G63-t G4 Plug-In Installation and Configuration Manual Mitsubishi VR4 4G63-t Copyright 2010 Link Installation Manual Copyright 2010 Link ElectroSystems Ltd PCLink Notice

More information

OPERATION AND MAINTENANCE

OPERATION AND MAINTENANCE Table of Contents GENERAL INFORMATION INTRODUCTION... 1 Operating Specifications... 1 FEATURES... 1 SAFETY PRECAUTIONS... 2 SET-UP... 2 OPERATION AND MAINTENANCE TESTING AN IGNITION MODULE OR IGNITION

More information

Lingenfelter TMR-001 Timer Delay Control Module

Lingenfelter TMR-001 Timer Delay Control Module Lingenfelter TMR-001 Timer Delay Control Module PN: L460290000 Revision - 1.1 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761 fax www.lingenfelter.com

More information

Getting Started HONDA

Getting Started HONDA Getting Started HONDA Product Introduction Congratulations on the purchase of your new AccessPORT handheld programmer. This quick start guide explains how to install the AP on your vehicle. Refer to the

More information

Matson Jump Starter Operator s Manual

Matson Jump Starter Operator s Manual Matson Jump Starter Operator s Manual RA3800 SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for the RA3800 Jumpstart. Read through this owner s manual carefully

More information

Dodge Cummins 5.9L 24 Valve Edge Products EZ Module Installation Instructions & Manual

Dodge Cummins 5.9L 24 Valve Edge Products EZ Module Installation Instructions & Manual 1998.5-2002 Dodge Cummins 5.9L 24 Valve Edge Products EZ Module Installation Instructions & Manual OLD P/N s: EZD1000 / EZD1000A / EZD1000B NEW P/N s: 30200 / 30201 2007 Edge Products All rights reserved.

More information

3-Stage Retard PN 8970

3-Stage Retard PN 8970 3-Stage Retard PN 8970 IMPORTANT: Read the instructions before attempting the installation. Parts Included: 1-3-Stage Retard Control 4 - Mounting Screws 4 - Mounting Grommets 6 - Retard Modules, 2, 3,

More information

Product Warranty Statement

Product Warranty Statement Honda Civic Gen 5 Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others. For

More information

Infinitybox Express Road Race Car Kit Installation Guide

Infinitybox Express Road Race Car Kit Installation Guide Table of Contents Infinitybox Express Road Race Car Kit Installation Guide Overview... 2 Warnings... 3 J1939 POWERCELL Technical Details... 4 IOX Input/Output Module Technical Details... 4 Kit Contents...

More information

Mitsubishi VR4 4G63-t

Mitsubishi VR4 4G63-t Mitsubishi VR4 4G63-t Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others.

More information

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue

More information

V8 Gen. V Ford Mustang 2010 Update

V8 Gen. V Ford Mustang 2010 Update V8 Gen. V Ford Mustang 2010 Update There were several updates to the Ford Mustang in the 2010 model year. This document outlines the differences between the installation steps necessary for the 2010 Mustang

More information

Installation Instructions for: EMS P/N Acura Integra Acura 2.3CL Honda Accord Honda Civic

Installation Instructions for: EMS P/N Acura Integra Acura 2.3CL Honda Accord Honda Civic Installation Instructions for: EMS P/N 30-6050 00-01 Acura Integra 98-99 Acura 2.3CL 98-02 Honda Accord 99-00 Honda Civic Thank you for purchasing an AEM Engine Management System. The AEM Engine Management

More information

MSD Start/Retard Control PN 8982

MSD Start/Retard Control PN 8982 MSD Start/Retard Control PN 8982 IMPORTANT: Read the instructions before attempting installation. Parts Included: 1 - Start/Retard Control, PN 8982 4 - Retard Modules, 0, 2, 3, 4 1 - Wiring Kit 4 - Mounting

More information

Installation Instructions for the Lingenfelter Fan and Pump Manual Override Kit

Installation Instructions for the Lingenfelter Fan and Pump Manual Override Kit Installation Instructions for the Lingenfelter Fan and Pump Manual Override Kit PN: L300180000 v1.1 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761

More information

Product Warranty Statement

Product Warranty Statement Arctic Cat M800 Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others. For

More information

Getting Started Guide Racing Supplement EXTREME CONTENTS INSIDE

Getting Started Guide Racing Supplement EXTREME CONTENTS INSIDE Getting Started Guide Racing Supplement EXTREME CONTENTS INSIDE Table of Contents What is a Superchips Racing tuner? Activating your Superchips Racing tuner Power Levels & Features Racing Features Definitions

More information

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor

More information

MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740

MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 MSD Coil Power Booster for Ford 4.6L/5.4L Mod Motors 99-On PN 8740 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issued with

More information

HOW TO INSTALL YOUR BOV

HOW TO INSTALL YOUR BOV Product Name: Product Description: Product Number: BMW Kompact BOV Kit Model specific BOV Kit TS-0203-1050/TS-0203-1250 ------------------------------------------------------------------------------------------------------------------------

More information

BMW Mini Cooper S R53

BMW Mini Cooper S R53 BMW Mini Cooper S R53 Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others.

More information

Link G4 Plug-In ECU. Subaru Impreza WRX V5-6. G4 Plug-In Installation and Configuration Manual. Subaru Impreza WRX V5-6. Copyright 2010 Link

Link G4 Plug-In ECU. Subaru Impreza WRX V5-6. G4 Plug-In Installation and Configuration Manual. Subaru Impreza WRX V5-6. Copyright 2010 Link Link G4 Plug-In ECU Subaru Impreza WRX V5-6 G4 Plug-In Installation and Configuration Manual Subaru Impreza WRX V5-6 Copyright 2010 Link Installation Manual Copyright 2010 Link ElectroSystems Ltd PCLink

More information

Overview of operation modes

Overview of operation modes Overview of operation modes There are three main operation modes available. Any of the modes can be selected at any time. The three main modes are: manual, automatic and mappable modes 1 to 4. The MapDCCD

More information

Link ElectroSystems Ltd. Limited Warranties Statement Effective April 5, p.m.

Link ElectroSystems Ltd. Limited Warranties Statement Effective April 5, p.m. Link ElectroSystems Ltd. Limited Warranties Statement Effective April 5,1992 5 p.m. All products manufactured or distributed by Link ElectroSystems Ltd. are subject to the following, and only the following,

More information

4-Port Aux Fuel Injection System Installation and User Guide

4-Port Aux Fuel Injection System Installation and User Guide Stratified Aux Fiesta ST 4-Port Aux Fuel Injection System Installation and User Guide Stratified 4-Port Aux Fuel System Installation and User Guide -1-0204-0025 Thank you and congratulations on the purchase

More information

Nissan 300ZX Z32 Installation Manual

Nissan 300ZX Z32 Installation Manual Nissan 300ZX Z32 Installation Manual Product Warranty Statement LINK ENGINE MANAGEMENT LTD LIMITED LIFETIME WARRANTY All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management

More information

SUPRA JZA80 TWIN TURBO BLOW-OFF VALVE ADAPTOR INSTRUCTIONS

SUPRA JZA80 TWIN TURBO BLOW-OFF VALVE ADAPTOR INSTRUCTIONS IMPORTANT NOTES ON FITTING YOUR SUPRA TWIN TURBO ADAPTOR Turbosmart recommends that your Blow Off Valve (BOV) and Adaptor kit is fitted by an appropriately qualified technician. ADAPTOR KIT CONTENTS Please

More information

MSD LS Ignition Control PN 6014/60143

MSD LS Ignition Control PN 6014/60143 MSD LS Ignition Control PN 6014/60143 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the

More information

Product Warranty Statement

Product Warranty Statement Toyota Supra Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others. For a

More information

MSD 7AL-3, Ignition Control PN 7230

MSD 7AL-3, Ignition Control PN 7230 MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,

More information

MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020

MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 INSTALLATION INSTRUCTIONS 1 MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 Important: Read these instructions before attempting this installation! Parts Included: 1 - MSD Stacker Ignition

More information

MAXIMIZER-II Progressive Nitrous Controller INSTALLATION AND USER MANUAL. MAXIMIZER-II rev A

MAXIMIZER-II Progressive Nitrous Controller INSTALLATION AND USER MANUAL. MAXIMIZER-II rev A MAXIMIZER-II Progressive Nitrous Controller INSTALLATION AND USER MANUAL i Table of Contents Page 1. Installation Overview...1 1.1 MAXIMIZER-II Power Input...1 1.2 SOLENOID DRIVER Ground...1 1.3 Arming

More information

60 PSI Boost Gauge. For Product Numbers: MT-DV01_60, MT-WDV01_60

60 PSI Boost Gauge. For Product Numbers: MT-DV01_60, MT-WDV01_60 60 PSI Boost Gauge For Product Numbers: MT-DV01_60, MT-WDV01_60 Red: 12v Constant (un-switched) Source (+) Orange: 12v Dimmer (switched) Source (+) (optional) White: 12v Ignition (switched) Source (+)

More information

Getting Started Guide Racing Supplement EXTREME CONTENTS INSIDE

Getting Started Guide Racing Supplement EXTREME CONTENTS INSIDE Getting Started Guide Racing Supplement EXTREME CONTENTS INSIDE Table of Contents What is a Superchips Racing tuner? Activating your Superchips Racing tuner Power Levels & Features Racing Features Definitions

More information

Installation Instructions for the Lingenfelter TBRC-001 Temperature Based Relay Controller

Installation Instructions for the Lingenfelter TBRC-001 Temperature Based Relay Controller Installation Instructions for the Lingenfelter PN: L460220000 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761 fax www.lingenfelter.com Revision

More information

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent

MSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor 1 - Rotor,

More information

Toyota MR2 Rev2-3 and Celica ST205

Toyota MR2 Rev2-3 and Celica ST205 Toyota MR2 Rev2-3 and Celica ST205 Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES,

More information

Subaru Impreza WRX V1-2

Subaru Impreza WRX V1-2 Subaru Impreza WRX V1-2 Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others.

More information

Adaptronic esel015 Select ECU for Nissan R32/R33/R34GTR Skyline and Z32 300ZX / Fairlady

Adaptronic esel015 Select ECU for Nissan R32/R33/R34GTR Skyline and Z32 300ZX / Fairlady 1 P a g e Adaptronic esel015 Select ECU for Nissan R32/R33/R34GTR Skyline and Z32 300ZX / Fairlady Applicable vehicles / engines: Nissan Skyline R32 (GTST and GTR) RB20DET and RB26DETT Nissan Skyline R33

More information

Honda Civic Gen 6 Installation Manual

Honda Civic Gen 6 Installation Manual Honda Civic Gen 6 Installation Manual Product Warranty Statement LINK ENGINE MANAGEMENT LTD LIMITED LIFETIME WARRANTY All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management

More information

For questions or technical support, 1. Wiring Reference:

For questions or technical support,  1. Wiring Reference: Warning: Before proceeding you are obligated to read and agree to the terms and conditions attached to this manual. Misuse of this product may cause injury or death. Incorrect installation may cause damage

More information

(R86049) WARNING: To reduce the risk of injury, the user must read and understand the operator s manual before using this product.

(R86049) WARNING: To reduce the risk of injury, the user must read and understand the operator s manual before using this product. OPERATOR S MANUAL 12 VOLT LITHIUM-ION BATTERY CHARGER 140446001 (R86049) Your charger has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety.

More information

BMWLink - BMW E36 M50TUB25

BMWLink - BMW E36 M50TUB25 - BMW E36 M50TUB25 Product Warranty Statement LINK ENGINE MANAGEMENT LTD LIMITED LIFETIME WARRANTY All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management Ltd are subject

More information

Product Warranty Statement

Product Warranty Statement POLARIS RZR Product Warranty Statement All products manufactured or distributed by Electronz Ltd are subject to the following, and only the following, LIMITED EXPRESS WARRANTIES, and no others. For a period

More information

PLEASE READ BEFORE CALLING OR RETURNING PRODUCT. EXTREMELY IMPORTANT!!!

PLEASE READ BEFORE CALLING OR RETURNING PRODUCT. EXTREMELY IMPORTANT!!! Thank you for your purchase of WeaponX Smart Direct Fire Ignition Coil System for your vehicle. The following are the instruction manuals for your ignition system kit. Please read carefully and enjoy your

More information

The function of this Dynamic Active Probe has divided into three preferences on the screen main Menus:

The function of this Dynamic Active Probe has divided into three preferences on the screen main Menus: 1.0 Introduction: This probe is designed to provide an additional help to automotive technicians in trouble shooting of electrical circuits problems in the car. Apart from using the normal multi tester,

More information

MSD Blaster Ignition PN 5900

MSD Blaster Ignition PN 5900 MSD Blaster Ignition PN 5900 Note: Read these instructions completely before attempting any installation. Parts Included: 1 - Blaster Ignition, PN 5900 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground

More information

12/05/2012 Lockup Co-Pilot Instructions INST. Installation Manual v1.6: Dodge 68RFE Automatic Transmission

12/05/2012 Lockup Co-Pilot Instructions INST. Installation Manual v1.6: Dodge 68RFE Automatic Transmission Installation Manual v1.6: 2007.5-09 Dodge 68RFE Automatic Transmission Please read all instructions before the installation of the ATS Co-Pilot Thank you for purchasing the ATS Co-Pilot transmission management

More information

Audi TT (1.8l Turbo) Installation Manual

Audi TT (1.8l Turbo) Installation Manual Audi TT (1.8l Turbo) Installation Manual Product Warranty Statement LINK ENGINE MANAGEMENT LTD LIMITED LIFETIME WARRANTY All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management

More information

Link G4 Plug-In ECU. Subaru Impreza WRX V7-9. G4 Plug-In Installation and Configuration Manual. Subaru Impreza WRX V7-9. Copyright 2010 Link

Link G4 Plug-In ECU. Subaru Impreza WRX V7-9. G4 Plug-In Installation and Configuration Manual. Subaru Impreza WRX V7-9. Copyright 2010 Link Link G4 Plug-In ECU Subaru Impreza WRX V7-9 G4 Plug-In Installation and Configuration Manual Subaru Impreza WRX V7-9 Copyright 2010 Link Installation Manual Copyright 2010 Link ElectroSystems Ltd PCLink

More information

Link G4 Plug-In ECU. Toyota MR2 Rev2-3 and Celica ST205. G4 Plug-In Installation and Configuration Manual. Copyright 2010 Link. Installation Manual

Link G4 Plug-In ECU. Toyota MR2 Rev2-3 and Celica ST205. G4 Plug-In Installation and Configuration Manual. Copyright 2010 Link. Installation Manual Link G4 Plug-In ECU Toyota MR2 Rev2-3 and Celica ST205 G4 Plug-In Installation and Configuration Manual Toyota MR2 Rev2-3 and Celica ST205 Copyright 2010 Link Installation Manual Copyright 2010 Link ElectroSystems

More information

Installation Instructions for: EMS P/N Eclipse Turbo, Talon Tsi, Laser RS Galant VR4

Installation Instructions for: EMS P/N Eclipse Turbo, Talon Tsi, Laser RS Galant VR4 Installation Instructions for: EMS P/N 30-6300 1990-1994 Eclipse Turbo, Talon Tsi, Laser RS Galant VR4 Thank you for purchasing an AEM Engine Management System. The AEM Engine Management System (EMS) is

More information

INSTRUCTIONS: JOEY 30 CART (MK2)

INSTRUCTIONS: JOEY 30 CART (MK2) INSTRUCTIONS: JOEY 30 CART (MK2) Congratulations on your purchase. Follow these instructions for easy and fast set-up of your Joey 30 Cart. For video instructions, go to https://vimeo.com/144317620 Warranty:

More information

Tractor Applications Rapid Power Model Number

Tractor Applications Rapid Power Model Number INSTALLATION Manual Tractor Applications Rapid Power Model Number John Deere 8130 to 8530 40605 John Deere 8230 (T) to 8430 (T) 40605 TABLE OF CONTENTS TROUBLESHOOTING: If you have questions during the

More information

LU27 Series Quick Start

LU27 Series Quick Start Ultrasonic Liquid Level Transmitter LU27 Series Quick Start 2016 Flowline, Inc. All Rights Reserved Made in USA Flowline, Inc. 10500 Humbolt Street, Los Alamitos, CA 90720 p 562.598.3015 f 562.431.8507

More information

Boost Sensor Kit Instructions. Table of Contents

Boost Sensor Kit Instructions. Table of Contents V 1.5, 18 Jan, 2012 FW 1.01 Boost Sensor Kit Instructions Table of Contents 1. Introduction 2. Assembly 3. Installation 4. Set up 5. Launch 6. Operation 7. Fault Indications 1. Introduction. Thanks for

More information

RECOMMENDATIONS Turbosmart recommends that your Blow off valve (BOV) is fitted by an appropriately qualified technician

RECOMMENDATIONS Turbosmart recommends that your Blow off valve (BOV) is fitted by an appropriately qualified technician Product Name: Product Description: Product Number: BOV Kompact Hyundai Veloster BOV Kompact DP/PB Hyundai Veloster TS-0203-1X31 ------------------------------------------------------------------------------------------------------------------------

More information

DFS-1000 Wiring Diagrams and PC Software Installation.

DFS-1000 Wiring Diagrams and PC Software Installation. DFS-1000 Wiring Diagrams and PC Software Installation. For Technical Support Please contact your dealer or email seellc@mchsi.com 1 Important Information - When using a conventional style ignition coil

More information

E24/E28 M30 Mass Air Flow Conversion System Instruction Manual Version 2.0

E24/E28 M30 Mass Air Flow Conversion System Instruction Manual Version 2.0 E24/E28 M30 Mass Air Flow Conversion System Instruction Manual Version 2.0 Miller Performance Ltd. Tel 855.BMW.TUNER 2009 Abbotsford Way, Abbotsford BC, V2S 6Y5 Millerperformancecars.com Table of Contents:

More information

Holden VL (RB30) Installation Manual

Holden VL (RB30) Installation Manual Holden VL (RB30) Installation Manual Product Warranty Statement LINK ENGINE MANAGEMENT LTD LIMITED LIFETIME WARRANTY All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management

More information

MFI Pro - Instructional Manual (Toyota 1uzfe) Version 06.01

MFI Pro - Instructional Manual (Toyota 1uzfe) Version 06.01 Tel: 011 3971953 - Fax: 011 3978197 - info@gotech.co.za www.got e ch.c o.za MFI Pro - Instructional Manual (Toyota 1uzfe) Version 06.01 Index: Introduction 1 Before You Begin 1 Basic Tools Required 2 Basic

More information

Prop-Tech Vacuum Analyzer

Prop-Tech Vacuum Analyzer Electronic Carburettor / Injector Balancing Tool 1. WARNING THIS PRODUCT IS A PROFESSIONAL TOOL WHICH SHOULD ONLY BE OPERATED BY A COMPETENT TRAINED TECHNICIAN AND ONLY FOR THE PURPOSE WHICH IT WAS DESIGNED

More information

Installation Manual v1.0: Dodge 68RFE Automatic Transmission. Please read all instructions before the installation of the ATS Co-Pilot

Installation Manual v1.0: Dodge 68RFE Automatic Transmission. Please read all instructions before the installation of the ATS Co-Pilot 09/30/11 601-900-2356-INST Installation Manual v1.0: 2010-11 Dodge 68RFE Automatic Transmission Please read all instructions before the installation of the ATS Co-Pilot Thank you for purchasing the ATS

More information

3-Stage Retard PN 8970

3-Stage Retard PN 8970 3-Stage Retard PN 8970 IMPORTANT: Read the Instructions before attempting the installaiton. Parts Included: 1-3-Stage Retard Control 4 - Mounting Screws 4 - Mounting Grommets 6 - Retard Modules, 2, 3,

More information

MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595

MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark

More information

Nissan R34 25GT-T Installation Manual

Nissan R34 25GT-T Installation Manual Nissan R34 25GT-T Installation Manual Product Warranty Statement LINK ENGINE MANAGEMENT LTD LIMITED LIFETIME WARRANTY All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management

More information

Mazda RX7 Series 7-8 Installation Manual

Mazda RX7 Series 7-8 Installation Manual Mazda RX7 Series 7-8 Installation Manual Product Warranty Statement LINK ENGINE MANAGEMENT LTD LIMITED LIFETIME WARRANTY All Engine Control Units (ECUs) manufactured or distributed by Link Engine Management

More information